MBU-12/P Oxygen Mask - transaeroinc.com · The MBU-12/P mask is designed to replace the MBU-5/P and...
Transcript of MBU-12/P Oxygen Mask - transaeroinc.com · The MBU-12/P mask is designed to replace the MBU-5/P and...
MBU-12/P Oxygen Mask
The MBU-12/P meets or exceeds the requirements
of U.S. Air Force Specification MIL-M-87163.
The MBU-12/P mask is designed to replace the
MBU-5/P and offers substantial improvement in
comfort and efficiency when compared to the older
mask. The MBU-12/P features a gray silicone rubber
faceseal integrally bonded to a high strength gray
polysulfone plastic hardshell.
The shape of the MBU-12/P mask provides excellent
downward vision. The low profile design brings the
mask close to the face and provides excellent stability
during high G maneuvers. Anti-roll webs at the nose
seal prevent downward roll off. The inherent rigidity
of the integral faceseal/hardshell allows adjustment
to provide superior sealing during pressure breathing.
Four mask sizes are available to assure proper fit and
comfort.
The unique design of the Gentex developed
combination breathing valve distinguishes the
Gentex Model of the MBU-12/P. Using concepts
developed during the space program, this valve offers
greatly reduced exhalation resistance during pressure
breathing. Additionally, the rolling diaphragm reduce
the potential for valve sticking caused by residue
accumulation. The combination valve meets or
exceed all performance requirements of MIL-V-27296.
FSC# 27541
Transaero, inc.
35 Melville Park Road, Suite 100
Melville, NY, USA 11747
T 631.752.1240 F 631.752.1242
transaeroinc.com
12/09
631.752.1240
transaeroinc.com
Standard configuration
Weight
The weight of each size does not exceed 17.64 ounces
(0.5 kg) when the mask assembly includes all major
components listed in MIL-M-87163.
Hardshell/Facepiece
Consists of a gray silicone rubber faceseal bonded
to a gray polysulfone hardshell.
Combination Valve
Pressure compensation combination inhalation/exhalation
type valve with silicone elastomers.
Hose Assembly
Convoluted silicone rubber hose with 3/4 inch internal
diameter.
3-Pin Bayonet Hose Connector
Standard MS27796 type three pin locking bayonet hose
connector designed to mate with CRU-60/P or similar
connectors.
Offset Bayonet Connectors
Double eyelet, oxygen mask connector conforming
to Gentex Drawing No. 78B3595.
Communications Cord and Plug
CX-4707C/AIC cord terminal at branched (mask) end
with U-173/U connectors and with U-174/U plug at the
aircraft interface end.
Microphone (Standard USAF Mask)
Military Type M-101/AIC noise cancelling dynamic
microphone with 7 ohms impedance (+2 ohms)
and a frequency response of 400-5000 Hz.
Accessories and options
AM-7067A Audio Amplifier
A carbon compatible audio frequency preamplifier
to permit use of dynamic mask microphone with
carbon-type radio systems. Suitable for use with the
MBU-12/P oxygen mask subassembly to interface with
an M-94B/A or M-101/AIC dynamic microphone with the
US Navy intercommunications system. The amplifier is in
accordance with MIL-M-23595 and in general accordance
with 765AS287.
Gentex carries all of the necessary tools to support
maintenance of the MBU-12/P oxygen mask. Each
is available for individual purchase.
Performance
Tear Resistance
The silicone rubber used in the manufacture of the
MBU-12/P has a minimum tear resistance of 26269
newtons per meter (150 pounds per inch).
Toxicity
The silicone rubber used in the mask assembly does
not contain any chemicals or materials that have toxic
properties.
Dielectric Strength
The microphone connector withstands without flashover
or breakdown, the application of a 250-volt alternating
potential of commercial line frequency.
Combination Valve
Meets or exceeds the requirements of MIL-V-27296.
Superior exhalation resistance compared to requirements
as follows:
Test Specification Gentex valve
requirements (max) performance (average*)
Exhalation Resistance
@ 50 LPM
pressure demand 1.50 inches H20 .97 inches H20
@ 50 LPM
pressure demand 1.50 inches H20 .68 inches H20
@ 100 LPM
pressure demand 2.60 inches H20 1.18 inches H20
*Valves shown are average of laboratory tests and are for comparison only.
Product information
P/N NSN Size
G012-1001-01 1660-01-140-9399 Short
G012-1001-02 1660-01-140-9400 Regular
G012-1001-03 1660-01-140-9401 Long
G012-1001-04 1660-01-140-9402 X-Long