P.O. Box 755 Ennis, TX 75120 PH: (214) 515-5000 FX: (972) 875-9425

The information contained in this document is based on data and knowledge considered to be true and accurate and is offered for the users’ consideration, investigation and verification. Polyguard Products, Inc. cannot be held liable for errors made as a result of information herein. Changes and modifications can be made to this document without prior notice. No statement, recommendation or suggestion is intended for use which would infringe on patents or copyrights held by Polyguard Products, Inc. Airlok®, Airlok Flex®, Deckguard®, Polyflow®, Proban®, and Underseal® are Registered Trademarks of Polyguard Products, Inc.

www.Polyguard.com Materials List R3.10.17

MATERIALS CHECKLIST POLYGUARD® SPECIALTY SHEET MEMBRANES

WATERPROOFING SYSTEM: SPECIALTY SHEET MEMBRANES Polyguard NW-75 Membrane NW-75 Membrane is an asphalt overlay material for new and remedial bridge deck and pavement work. Mechanical and adhesive bond protects asphalt substrates from moisture and reflective cracking. Designed to be topped with a minimum 2” thickness of 280°F (138ºC) to 300°F (149ºC) asphalt.

Check Polyguard NW-75 Membrane *Accessories may be required – contact Polyguard Products

Part Number Unit Size Units/pallet Wt/unit

NW7548 48” x 50’ roll (1 roll/ctn) 25 ctns/pallet 65#/ctn

Polyguard Deckguard® HT Deckguard® HT is designed as a high temperature underlayment (260°F) for under shingles, tile, or standing seam metal roofing.

Check Polyguard Deckguard® HT *Accessories may be required – contact Polyguard Products

Part Number Unit Size Units/pallet Wt/unit

DGHT36 36” x 75’ roll (1 roll/ctn) 36 ctns/pallet 65#/ctn

Polyguard Tileguard™ Tileguard™ is designed as a reflective crack underlayment for ceramic tile.

Check Polyguard Tileguard™*Accessories may be required – contact Polyguard Products

Part Number Unit Size Units/pallet Wt/unit

TI37 37” x 63.3’ roll (1 roll/ctn) 36 ctns/pallet 65#/ctn

Weights listed are estimates.

Product Data Sheet NW-75 MEMBRANE Pavement Membrane PRODUCT NAME NW-75 Membrane MANUFACTURER Polyguard Products, Inc. Ennis, TX 75119 (214) 515-5000 www.polyguard.com PRODUCT DESCRIPTION NW-75 Membrane is designed for use prior to an asphalt overlay on parking garages and parking lots. PRODUCT FEATURES • The non-woven geotextile fabric used as backing on the

NW-75 Membrane has an advantage in that its open woven fibers will provide a mechanical bond to the asphalt overlay.

• Flexible at low temperatures. • Impermeable to moisture.

COMPOSTION & MATERIALS NW-75 Membrane is comprised of a rubberized-asphalt waterproofing sealant with a non-woven, pavement-reinforcing-grade polypropylene fabric laminated to the outer surface. A peel-off silicone-treated release liner keeps the rubberized asphalt from sticking to the membrane when rolled up. TECHNICAL DATA See physical properties table. INSTALLATION SURFACE PREPARATION Pavement surfaces must be clean and dry prior to application. A surface profile of 3-to-5 must be maintained to obtain complete adhesion. Surfaces must be free of voids, sharp projections and debris or aggregate. New concrete must be cured a minimum of 7 days, and surfaces must be free of curing agents and other contaminants. Do not use curing compounds containing oil, wax, silicone, or pigments. Apply LM-95 fillet or cant strip to clean, dry deck and curb to avoid a sharp angle. Do not apply 650 LT Liquid Adhesive or California Sealant prior to LM-95. PRIMING Prepare substrate with 650 LT Liquid Adhesive or California Sealant at a rate of 250 - 300 square feet per gallon to clean, dry concrete. Allow to dry tacky to touch.

MEMBRANE APPLICATION Apply a 12” flashing strip of NW-75 Membrane to curb, placing the membrane equally 6” in both directions of the joint. Keep the flashing strip just below the planned height of asphalt. Press firmly to eliminate any fishmouths or gaps. Then apply the field membrane straight and wrinkle free, with no curled edges, and from low to high pitch to provide tight seal. Side laps should be a minimum of 3”. End laps should be a minimum of 6”. Pressure roll all membrane with a 75 – 100 lb roller. Any wrinkles over 3/8” in width should be slit and folded down. For all non-moving joints or cracks over 3/16” width, apply a 12” flashing strip of NW-75 Membrane first then continue with the full width membrane. Address expansion joints using the appropriate expansion joint material. Apply a bead of 650 Mastic to the top termination of the NW-75 Membrane on the curb. PAVING Apply a tack coat of AC20 over the installed membrane prior to asphalt overlay. A minimum compacted thickness of less than 1-1/2” is not recommended. Paving temperatures at compaction must be 290°F – 340°F. Use of vibratory rollers during paving is not recommended. INSPECTION Inspect all membrane for tears, wrinkles, air blisters and damage from other trades prior to asphalt application and repair as needed. REPAIR Remove all damaged membrane so that only bonded membrane remains. Reprime any exposed concrete and apply a new sheet of membrane over the concrete and over the previously applied membrane a minimum of 6 inches in all directions. STORAGE AND HANDLING Material Handling Unload and store NW-75 Membrane and accessories carefully. Protect cartons and containers from weather, sparks, flames, excessive heat, cold and lack of ventilation. DO NOT stack membrane material higher than 5 feet vertically, nor double stack pallets. Store cartons on pallets and cover to prevent water damage. For best results, store membrane above 50°F (10ºC) prior to application. PRECAUTIONS • DO NOT use this product when parking garage is over

occupied living or working space. • The 650 LT Liquid Adhesive and California Sealant are

considered industrial coatings and would be harmful or

P.O. Box 755 Ennis, TX 75120 PH: (214) 515-5000 FX: (972) 875-9425

The information contained in this document is based on data and knowledge considered to be true and accurate at time of printing and is offered for the users’ consideration, investigation and verification. Polyguard Products, Inc. cannot be held liable for errors made as a result of information herein. Changes and modifications can be made to this document without prior notice. No statement, recommendation or suggestion is intended for use which would infringe on patents or copyrights held by Polyguard Products, Inc.

www.Polyguard.com

X:/ArchDiv/ArchProdDoc/NW-75 Membrane R05.19.15

fatal if swallowed. It is marked as red label from the stand-point of flash point.

• Prohibit flames, sparks, welding and smoking during application.

• Refer to product label for handling, using and storage precautions.

• Solvents could be irritating to the eyes; flush with water and contact physician.

• Avoid prolonged contact with skin and breathing of vapor or spray mist from liquid adhesive. In confined areas, use adequate forced ventilation, fresh air masks, explosion-proof equipment and clean clothing.

• Avoid solvent contact with light bulbs or other high- temperature surfaces.

Ultraviolet Protection NW-75 Membrane is adversely affected by ultraviolet light. Cover the waterproofing system as soon as possible; DO NOT leave exposed to sunlight for over 30 days. SAFETY SDS documents for all Polyguard products can be obtained at our website www.polyguard.com. Call Polyguard Products, Inc. at (214) 515-5000 with questions.

WARRANTY We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product are beyond our control; such as weather, workmanship, equipment utilized and prior condition of the substrate. We will replace at no charge product proved to be defective within twelve (12) months of purchase, provided it has been applied in accordance with our written directions for uses we recommended as suitable for this product. Proof of purchase must be provided. A five (5) year material or system warranty may be available upon request. Contact Polyguard Products, Inc. for further details. TECHNICAL SERVICES Technical assistance, information and Polyguard’s products are available through a nationwide network of distributors and architectural representatives, or contact Polyguard Products, Inc. P.O. Box 755, Ennis, TX 75120-0755 Sales: (615) 217-6061•Tech Support: (214) 515-5000•Fax: (615) 691-5500 Email: archtech@polyguard.com Website: www.polyguard.com

PROPERTY TEST METHOD TYPICAL VALUE MEMBRANE THICKNESS ASTM D 1777 65 mils TENSILE BREAKING STRENGTH ASTM D 882 41 lbs./in. width TENSILE ELONGATION STRENGTH ASTM D 882 127% GRAB TENSILE STRENGTH ASTM D 4632 187 lbs. PUNCTURE RESISTANCE ASTM E 154 281 lbs. WATER VAPOR TRANSMISSION ASTM E 96 Method B 0.0316 perm ADHESION TO CONCRETE ASTM D 903 6.35 lbs./in. width PLIABILITY ASTM D 146 Pass

PACKAGING PART NUMBER UNIT SIZE NW-75 MEMBRANE NW7548 48” x 50’ Accessories: 650 LT LIQUID ADHESIVE 650-5 LIQ ADH 5 GA 5 gallon pail 650 LT LIQUID ADHESIVE 650-5 LIQ ADH 1 GA 4 – 1 gal pails/ctn CALIFORNIA SEALANT CALSEAL5 5 gallon pail LM-95 LM952 2 gallon pail 650 MASTIC 650-5-MASTIC 5 gallon pail 650 MASTIC 650-QTUBES-MASTIC 12/30 oz. tubes

P.O. Box 755 Ennis, TX 75120 PH: (214) 515-5000 FX: (972) 875-9425

The information contained in this document is based on data and knowledge considered to be true and accurate at time of printing and is offered for the users’ consideration, investigation and verification. Polyguard Products, Inc. cannot be held liable for errors made as a result of information herein. Changes and modifications can be made to this document without prior notice. No statement, recommendation or suggestion is intended for use which would infringe on patents or copyrights held by Polyguard Products, Inc.

www.Polyguard.com

X:/ArchDiv/ArchProdDoc/ 650 LT Liquid Adhesive R09.14.15

Product Data Sheet 650 LT LIQUID ADHESIVE Waterproofing Adhesive PRODUCT NAME 650 LT Liquid Adhesive

MANUFACTURER Polyguard Products, Inc. Ennis, TX 75119 (214) 515-5000 www.polyguard.com

PRODUCT DESCRIPTION BASIC USES 650 LT Liquid Adhesive is an integral part of the Polyguard Waterproofing System and sufficient liquid adhesive must be used on dry surfaces to condition them to be dust free so the substrate is suitable for the application of Polyguard Waterproofing Membranes. 650 LT Liquid Adhesive will be a red color in appearance. PRODUCT FEATURES • Used to prime all structural concrete, masonry, or wood

surfaces on which Polyguard Membranes will be applied. • Designed to be used on applications down to 25°F (-4ºC). • Used on all concrete block and brick wall conditions. COMPOSITION & MATERIALS 650 LT Liquid Adhesive is a rubber-based, tacky adhesive which is specifically formulated to provide excellent adhesion. TECHNICAL DATA Polyguard Products, Inc. provides design data and installation instructions to architects, engineers, specifiers, and contractors. INSTALLATION APPLICATION 650 LT Liquid Adhesive may be applied with roller or brush. A roller with a heavy nap should be used to carry sufficient material to the area being primed. Apply 650 LT Liquid Adhesive to a clean, dry, dust free, and frost free surface at a coverage rate of approximately 250 to 300 square feet per gallon on concrete. Exterior gypsum sheathing board products will vary in texture, performance and porosity. The coverage rate for Polyguard Adhesive/Sealants will be less than over concrete substrates. Specific testing for coverage is recommended. Other substrates may vary in coverage, please test according. The liquid adhesive should be spread sufficiently to avoid areas of excess material. Areas

of excess material will lengthen the curing time on the application of the 650 LT Liquid Adhesive. For best results apply 650 LT Liquid Adhesive and allow to become tacky to touch. Porosity of substrates could affect the tackiness of the adhesive; timing may vary due to atmospheric conditions. At this point the membrane overlay should be applied. LIMITATIONS Limit the application of liquid adhesive to what can be covered with Polyguard Membranes in one working day. Any areas not covered with membrane during the day must be recoated, and be sure to cover all open containers when not applying liquid adhesive. If adhesive dries and is no longer tacky, then reapply the adhesive. When used on horizontal surfaces, the liquid adhesive’s tacky nature may cause adhesion/bond to unwanted materials; so precautions must be used in this application. SAFETY SDS documents for all Polyguard products can be obtained at our website www.polyguard.com. Call Polyguard Products, Inc. at (214) 515-5000 with questions. WARRANTY We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product are beyond our control; such as weather, workmanship, equipment utilized and prior condition of the substrate. We will replace at no charge product proved to be defective within twelve (12) months of purchase, provided it has been applied in accordance with our written directions for uses we recommended as suitable for this product. Proof of purchase must be provided. A five (5) year material or system warranty may be available upon request. Contact Polyguard Products, Inc. for further details. TECHNICAL SERVICES Technical assistance, information and Polyguard’s products are available through a nationwide network of distributors and architectural representatives, or contact Polyguard Products, Inc. P.O. Box 755, Ennis, TX 75120-0755 Sales: (615) 217-6061•Tech Support: (214) 515-5000•Fax: (615) 691-5500 Email: archtech@polyguard.com Website: www.polyguard.com

PACKAGING PART NUMBER UNIT SIZE

650 LT LIQUID ADHESIVE 650-5 LIQ ADH 5 GA 5 gallon pail 650 LT LIQUID ADHESIVE 650-5 LIQ ADH 1 GA 4 – 1 gal pails/ctn

P.O. Box 755 Ennis, TX 75120 PH: (214) 515-5000 FX: (972) 875-9425

The information contained in this document is based on data and knowledge considered to be true and accurate at time of printing and is offered for the users’ consideration, investigation and verification. Polyguard Products, Inc. cannot be held liable for errors made as a result of information herein. Changes and modifications can be made to this document without prior notice. No statement, recommendation or suggestion is intended for use which would infringe on patents or copyrights held by Polyguard Products, Inc.

www.Polyguard.com

X:/ArchDiv/ArchProdDoc/California Sealant R09.03.15

Product Data Sheet CALIFORNIA SEALANT Adhesive/Sealant PRODUCT NAME California Sealant MANUFACTURER Polyguard Products, Inc. Ennis, TX 75119 (214) 515-5000 www.polyguard.com PRODUCT DESCRIPTION BASIC USES California Sealant is an integral part of Polyguard Membrane systems and sufficient liquid sealant must be used on dry surfaces to condition them to be dust free so that the substrate is suitable for the application of Polyguard Membranes. California Sealant is used to seal overlap areas of Underseal® Underslab and Underseal® Blindside where geotextile fabric comes in contact with polyethylene backing. The function of the sealant is to seal all porous portions of the geotextile surface. PRODUCT FEATURES • Used to prime all structural concrete, masonry, or wood

surfaces on which Polyguard Membranes will be applied. • Designed to be used on applications down to 25°F (-4ºC). • Used on all concrete block and brick wall conditions. COMPOSITION & MATERIALS California Sealant is a rubber-based sealant which is specifically formulated to provide excellent adhesion. The VOC (Volatile Organic Compound) content meets the South Coast Air Quality Management District regulations established under the February 1, 1991 version of Rule 1168 ©) (2) Adhesion and Sealant Applications. California Sealant is classified as an Architectural Sealant Primer Porous, with VOC of 527 g/L. Current SCAQMD regulations for this type sealant primer are 775 g/L. California Sealant will be orange color in appearance. TECHNICAL DATA Polyguard Products, Inc. provides design data and installation instructions to architects, engineers, specifiers, and contractors. INSTALLATION California Sealant may be applied with roller or brush. A roller with a heavy nap should be used to carry sufficient material to the area being coated. Apply California Sealant to a clean, dry, dust free, and frost free surface at a coverage rate of approximately 250 to 300 square feet per gallon on concrete. Exterior gypsum

sheathing board products will vary in texture, performance and porosity. The coverage rate for Polyguard Adhesive/Sealants will be less than over concrete substrates. Specific testing for coverage is recommended. Other substrates may vary in coverage, please test according. The liquid sealant should be spread sufficiently to avoid areas of excess material. Areas of excess material will lengthen the curing time on the application of the California Sealant. For best results California Sealant should be applied and allowed to become tacky to touch. Porosity of substrates could affect the tackiness of the adhesive; timing may vary due to atmospheric conditions. At this point membrane should be applied. LIMITATIONS The application of liquid sealant should be limited to what can be covered with Polyguard Membranes in one working day. Any areas not covered with membrane during the day must be recoated, and be sure to cover all open containers when not applying liquid sealant. If liquid sealant dries and is no longer tacky, then reapply liquid sealant. When used on horizontal surfaces, the sealant remains tacky, and precautions must be used in this application. SAFETY SDS documents for all Polyguard products can be obtained at our website www.polyguard.com. Call Polyguard Products, Inc. at (214) 515-5000 with questions. WARRANTY We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product are beyond our control; such as weather, workmanship, equipment utilized and prior condition of the substrate. We will replace at no charge product proved to be defective within twelve (12) months of purchase, provided it has been applied in accordance with our written directions for uses we recommended as suitable for this product. Proof of purchase must be provided. A five (5) year material or system warranty may be available upon request. Contact Polyguard Products, Inc. for further details. TECHNICAL SERVICES Technical assistance, information and Polyguard’s products are available through a nationwide network of distributors and architectural representatives, or contact Polyguard Products, Inc. P.O. Box 755, Ennis, TX 75120-0755 Sales: (615) 217-6061•Tech Support: (214) 515-5000•Fax: (615) 691-5500 Email: archtech@polyguard.com Website: www.polyguard.com

PACKAGING PART NUMBER UNIT SIZE

CALIFORNIA SEALANT CALSEAL5 5 gallon pail

Product Data Sheet LM-95 Two-Component Fast Cure Urethane Waterproofing Membrane PRODUCT NAME LM-95

MANUFACTURER Polyguard Products, Inc. Ennis, TX 75119 (214) 515-5000 www.polyguard.com

PRODUCT DESCRIPTION LM-95 is a two-component, asphalt-modified, urethane material. BASIC USES LM-95 is designed to be used with Polyguard Membranes for several different types of detailing applications. It may be used as a fillet at the junction of the footing and foundation, a collar around drain detailing area, and a termination flashing material for protrusions through the waterproofing system. It can also be used for terminations and flashings to curbs and parapets on plaza decks or other similar horizontal applications. COMPOSITION AND MATERIALS LM-95 is a two-component, asphalt-modified, urethane material.

TECHNICAL DATA See physical properties table.

INSTALLATION Apply LM-95 in ambient and surface temperatures of 40°F (5ºC) and rising. Coverage of one gallon of LM-95 is approximately: • Flashings: 17 square feet • Fillet & Reinforcement: 14 linear feet • Fillet Only: 65 linear feet

When working with materials in these cold temperatures, store the LM-95 in a warm area or warm-up before the mixing and application. All surfaces to receive LM-95 must be free of contaminants and dry for the application. Areas to receive LM-95 should not be primed for the membrane. For best results and lower viscosity, warm-up both LM-95 components A and B between 50°F (24°C) to 95°F (35°C) prior to mixing. To mix the two pre-measured components of the LM-95, using a 1/2-inch drill with an all-steel 2 1/2-gallon spiral mixer: mix component A thoroughly for 3 minutes, add component B to component A; thoroughly mix for an additional 2 minutes. DO NOT APPLY ANY MATERIAL IF STREAKS CAN BE SEEN DUE TO INSUFFICIENT MIXING. Once LM-95 is mixed, it may be applied with a trowel or a bulk caulking gun within 45 minutes. Curing time may be accelerated at high temperatures. Once the material has started to thicken, it must be discarded. The material will cure to a very flexible, rubber like material. Potable life at 75°F (24ºC) and 50% relative humidity is approximately 45 minutes, longer for cooler temperatures

and higher humidity and shorter for hotter temperatures and lower humidity. Discard material that won’t flow freely. The 650 Waterproofing Membrane may be applied directly over LM-95 before it is cured. LM-95 must be applied in a minimum of 90 mils of coverage, unless otherwise noted on any details. In a reinforcing or fillet application at footing and wall junction, under the 650 Waterproofing System, it should be applied with a minimum of 3/4-inch face. LM-95 may also be applied as a waterproofing detailing material in this junction, 6-inches in all directions from the corner. When used as a flashing at membrane terminations, LM-95 must be applied a minimum of 2-inches over the water-proofing membrane and a minimum of 1-inch onto the surface being waterproofed. LM-95 will adhere to primed or unprimed concrete but unprimed concrete is preferred. Before any flood testing should occur, a minimum cure of 3 hours must be allowed for LM-95. STORAGE Store LM-95 in temperatures between 40°F (5°C) and 80°F (27°C). If at any time in storage the Part B has been frozen, it must be discarded and replaced. Clean material from tools and application equipment with mineral spirits before the LM-95 material residue cures. Clean skin with a citrus-based cleaner. Refer to SDS document for further handling information.

SAFETY SDS sheets for all Polyguard products can be obtained at our website www.polyguard.com. Call Polyguard Products, Inc. at 214.515.5000 with questions.

WARRANTY We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product are beyond our control; such as weather, workmanship, equipment utilized and prior condition of the substrate. We will replace at no charge product proved to be defective within twelve (12) months of purchase, provided it has been applied in accordance with our written directions for uses we recommended as suitable for this product. Proof of purchase must be provided. A five (5) year material or system warranty may be available upon request. Contact Polyguard Products, Inc. for further details.

TECHNICAL SERVICES Technical assistance, information and Polyguard’s products are available through a nationwide network of distributors and architectural representatives, or contact Polyguard Products, Inc. P.O. Box 755, Ennis, TX 75120-0755 Sales: (615) 217-6061•Tech Support: (214) 515-5000•Fax: (615) 691-5500 Email: archtech@polyguard.com Website: www.polyguard.com

P.O. Box 755 Ennis, TX 75120 PH: (214) 515-5000 FX: (972) 875-9425

The information contained in this document is based on data and knowledge considered to be true and accurate at time of printing and is offered for the users’ consideration, investigation and verification. Polyguard Products, Inc. cannot be held liable for errors made as a result of information herein. Changes and modifications can be made to this document without prior notice. No statement, recommendation or suggestion is intended for use which would infringe on patents or copyrights held by Polyguard Products, Inc.

www.Polyguard.com

X:/ArchDiv/ArchProdDoc/LM-95 R09.25.15

PROPERTY TEST METHOD TYPICAL VALUE PART A

COLOR Black SPECIFIC GRAVITY ASTM D 70 1.29 FLASH POINT (C.O.C.) ASTM D 92 > 500°F

PART B COLOR Brown SPECIFIC GRAVITY ASTM D 70 1.20 FLASH POINT (S.C.C.) ASTM D 3278 > 375°F MIXTURE VISCOSITY @ 80°F BROOKFIELD @ 20 RPM ASTM D 2196 61 SOLIDS CONTENT ASTM D 1754 100%

PACKAGING PART NUMBER UNIT SIZE

LM-95 (A & B yields 1.64 Gallons) LM952 2 gallon pail

P.O. Box 755 Ennis, TX 75120 PH: (214) 515-5000 FX: (972) 875-9425

The information contained in this document is based on data and knowledge considered to be true and accurate at time of printing and is offered for the users’ consideration, investigation and verification. Polyguard Products, Inc. cannot be held liable for errors made as a result of information herein. Changes and modifications can be made to this document without prior notice. No statement, recommendation or suggestion is intended for use which would infringe on patents or copyrights held by Polyguard Products, Inc.

www.Polyguard.com

X:/ArchDiv/ArchProdDoc/650 Mastic R09.14.15

Product Data Sheet 650 MASTIC Adhesive/Sealant PRODUCT NAME 650 Mastic MANUFACTURER Polyguard Products, Inc. Ennis, TX 75119 (214) 515-5000 www.polyguard.com PRODUCT DESCRIPTION BASIC USES 650 Mastic is designed to protect the termination edges, overlaps, patches, and any additional detailing areas. On vertical applications, 650 Mastic must be applied on both the bottom and top terminations of the Polyguard Membrane systems. The 650 Mastic is a topping material only, not for use under a membrane sheet. COMPOSITION & MATERIALS 650 Mastic is a polymer modified, asphalt-based material. TECHNICAL DATA See physical properties table. INSTALLATION 650 Mastic is supplied either in a 5 gallon pail or in a 30 oz. caulking tube. If some material is applied with a caulking gun, the bead must be struck with a trowel to insure the 650 Mastic is worked into the termination edges. If the material is supplied in a pail, it may be applied with either a trowel or by hand using rubber gloves as precautions. When applied as a temporary cut-off, trowel the 650 Mastic over the membrane in a very thin layer and allow to cure a minimum of 12 hours before placement of additional 650 Membrane.

On the bottom edge of any vertical application, 650 Mastic must be applied liberally. Apply 650 Mastic also as a topical seal to the membrane edges after protrusions and drains are detailed properly with Polyguard LM-95 Liquid Membrane and any areas requiring patching. SAFETY SDS documents for all Polyguard products can be obtained at our website www.polyguard.com. Call Polyguard Products, Inc. at 214.515.5000 with questions. WARRANTY We, the manufacturer, warrant only that this product is free of defects, since many factors which affect the results obtained from this product are beyond our control; such as weather, workmanship, equipment utilized and prior condition of the substrate. We will replace at no charge product proved to be defective within twelve (12) months of purchase, provided it has been applied in accordance with our written directions for uses we recommended as suitable for this product. Proof of purchase must be provided. A five (5) year material or system warranty may be available upon request. Contact Polyguard Products, Inc. for further details. TECHNICAL SERVICES Technical assistance, information and Polyguard’s products are available through a nationwide network of distributors and architectural representatives, or contact Polyguard Products, Inc. P.O. Box 755, Ennis, TX 75120-0755 Sales: (615) 217-6061•Tech Support: (214) 515-5000•Fax: (615) 691-5500 Email: archtech@polyguard.com Website: www.polyguard.com

PROPERTY TEST METHOD TYPICAL VALUE Color Black Color Specific Gravity 1.12 Specific Gravity Flash Point (PM Closed Cup) 105°F Flash Point (PM Closed Cup)

PACKAGING PART NUMBER UNIT SIZE

650 MASTIC 650-5-MASTIC 5 gallon pail 650 MASTIC 650-QTUBES-MASTIC 12 – 30oz. tubes