Material testing & Q - ICH - Environmental Simulation Test - Temperature & Humidity Control
10
© BINDER GmbH 1 Dynamic Temperature &Climate Simulation Measurement April 2016 ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
-
Upload
analis -
Category
Technology
-
view
54 -
download
1
Transcript of Material testing & Q - ICH - Environmental Simulation Test - Temperature & Humidity Control
© BINDER GmbH 1
Dynamic Temperature &Climate Simulation Measurement
April 2016
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 2
Content
► Introduction
► Determination of the cooling rate acc. To IEC 60068-3-5
► Test Norms
► Temperature Distribution
► Humidity
► Systems & Solutions
► Applications ► Various sectors for climatic and testing chambers
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 3
Dynamic Temperature and Climate Simulation Chambers
BINDER environmental chambers are perfectly suited to material testing under dynamic conditions. The standard rapid alternation speeds of around 5 K/min make standard-compliant testing possible.
An environmental simulation chamber of the MK and MKT Series is suitable for complex temperature profiles in the range of -40 °C (MK) or -70 °C (MKT) to 180 °C.
MKF & MKFT suitable for rapide temperature and humidity control
INTRODUCTION
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 4
Determination of the cooling rate acc. To IEC 60068-3-5
► E.g. MK: ► Tmin = -40 °C ► Tmax = 180 °C Temperature span is 220 °C Maintain Tmax ( here 180°C ) - set point is Tmin
► Start measuring the time 158 °C when 90% of the temperature span are achieved (here 158 °C )► Stop time measurement when 10% of the temperature span are
reached ( here -18 °C ) To determine the cooling time Δt (min) Temperature differential ΔT is known► Unit of the cooling rate is ΔT/Δt °C/min
ΔT80% of the temperature span
Δt
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 5
Test Norms
► International and national test norms specify under which conditions constant and dynamic testing shall be performed
► The IEC (International Electrotechnical Commission) is a platform for industry and authorities
► The IEC is developing worldwide recognized International Standards for devices containing electro technology
► The IEC 60068 Standard specifies the conditions for environmental testing
► It is transformed into national and regional standards by the member committees (countries)
► The implementation in the EU is entitled EN 60068
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 9
Dynamic Temperature and Climate Simulation Chambers MK | Dynamic climate chambers for rapid temperature changes Temperature range: -40 °C to 180 °C
MKF | Dynamic climate chambers for rapid temperature changes with humidity control Temperature range: -40 °C to 180 °C - Humidity range: 10 % to 98 % RH -
MKT | Dynamic climate chambers for rapid temperature changes with extended low temperature range
Temperature range: -70 °C to 180 °C - 4 zero-voltage relay contacts that can be activated via MCS controller - Programmable condensation protection for test material
Heated viewing window with LED interior lighting
MKFT | Dynamic climate chambers for rapid temperature changes with humidity control and extended low temperature range
Temperature range: -70 °C to 180 °C - Humidity range: 10 % to 98 % RH
SYSTEMS & SOLUTION SEE MORE CLICK HERE
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 10
Applications : Automotive – Test Cycle for Adhesive Bonded Joints
0 1 3 4 5 6 7 8 9 10 11 12
-40
-20
0
20
40
60
80
100Temperature / °C Humidity / %
Time / h
Humidity offHumidity on
Duration per cycle: 12 hNumber of cycles: 20
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 11
Why is the extended climate range needed?
► Because various automotive test norms specify challenging temperature / humidity profiles where a fast dehumidification is mandatory
Humidity without controlled compresdry air purge
Humidity with controlled dry air purge see more
Temperature
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
© BINDER GmbH 12
Applications : BINDER MKF SYSTEMS in Polymer Research
► Technical University, located in Germany► Basic polymer research
► The Polymer Institute examines the Aging behavior Lower and upper destruct limits
of newly developed materials in order to validate the intended operation range referring to temperature and humidity
► The institute uses a BINDER MKF 240
► Stress testing polymer for several cyclic stress tests: Temperature cycle from -30 - 150 °C at different relative humidities between 30 – 98 % RH
More information click here
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
DOWNLOAD BINDER Artificial aging
© BINDER GmbH 13
Various sectors for climatic and testing chambers
Automotive Electro Components Test Laboratories Aviation Defense
Electronic devices Nano Technology Fine mechanics Construction materialsAuthorities
ANALIS SA/NV IS DISTRIBUTOR FOR BINDER ON BELGIUM AND LUXEMBOURG MARKET WWW.ANALIS.BE [email protected]
