Material Safety Data SheetMSDS Number: 23 -16

24 Hour Emergency Assistance: CHEMTREC -Domestic: (800) 424-930024 Hour Emergency Assistance: CHEMTREC -International: (703) 527-3887General Assistance Number: (713) 241-4819

MATERIAL IDENTITY: EPON@ Resin 828

COMPANY ADDRESS: Resolution Performance Products, P. O. Box 4500, Houston, TX 77210, USA

CAS#25068-38-6

CONCENTRATION100 %weight

COMPONENTSBisphenol A/Epichlorohydrin Based Epoxy Resin

Health Effects

Inhalation:This material does not normally present an inhalation hazard, however, in applications where vapors (caused byhigh temperature) or mists (caused by mixing) are created, breathing may cause a mild burning sensation in thenose, throat and lungs.

Eye Contact:May cause temporary discomfort or irritation to the eye. Contact with hot material can cause thermal burns whichmay result in permanent damage or blindness.

Skin Contact:May be slightly irritating to the skin. Repeated skin contact may result in an allergic skin reaction causing itching,burning, redness and swelling. Contact with hot material can cause thermal burns which may result in permanent

damage.

Inhalation:Move victim to fresh air.

Eye:Cool the exposed area by flushing with large amounts of water. Flush eyes with water while holding eyelids open.Rest eyes for 30 minutes. If redness, burning, blurred vision or swelling persist, consult a physician. Transport tonearest medical facility for additional treatment. .

Ingestion:Not expected to be a relevant route of exposure.

Skin:If contact with hot material, cool the burn area by flushing with large amounts of water. Wipe off excess materialfrom exposed area. Flush exposed area with water and follow by washing with soap if available. DO NOi ~tte'mptto remove anything from the burn area or apply burn creams or ointments. Cover the burn area loosely v .th "sterile dressing, if available. Transport to nearest medical facility for additional treatment.

Flash Point: 480°F /248.89°C

Extinguishing Media:Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.

Fire Fighting Instructions:Material will not burn unless preheated. Clear fire area of all non-emergency personnel. Do not enter confined firespace without full bunker gear (helmet with face shield, bunker coats, gloves and rubber boots), including apositive pressure, NIOSH approved, self-contained breathing apparatus. Cool surrounding equipment, fire-exposed containers and structures with water. Container areas exposed to direct flame contact should be cooledwith large quantities of water (500 gallons water per minute flame impingement exposure) to prevent weakening ofcontainer structure.

May burn although not readily ignitable.

Protective Measures:Wear appropriate personal protective equipment (refer to Section 8) when responding to spills.

Spill Management:Use cautious judgment when cleaning up large spills. Shut off source of leak if safe to do so. Dike and containspill. Remove with vacuum trucks or pump to storage/salvage vessels. Soak up residue with an absorbent suchas clay, sand or other suitable material and dispose of properly. Flush area with water to remove trace residue.Contain run-off from residue flush and dispose of properly. Place in container for proper disposal. Prevent entryinto waterways, sewer. basements or confined areas. Remove contaminated soil to remove contaminated traceresidues. Dispose of in same manner as material. For small spills: Soak up residue with an absorbent such asclay, sand or other suitable material. Place in non-leaking container and seal tightly for proper disposal.

Disposal:Proper disposal should be evaluated based on regulatory status of this material (refer to Section 13), potentialcontam!nation from subsequent use and spillage, and regulations governing disposal in the local area.

Reporting:Notify authorities if any exposures to the general public or environment occurs or is likely to occur.

Avoid prolonged or repeated contact with eyes, skin and clothing. Avoid contact, with eyes, skin and clothing. Donot get in eyes, on skin or on clothing. Wash thoroughly after handling.

Handling:This resin may be handled, shipped and stored at elevated temperature in bulk.temperature is 1800 F.

The recommended pumping

EPON@ Resin 828 MSDS# 23 Pace 2 of 5

Ingestion:DO NOT induce vomiting. Have victim rinse mouth out with water, then drink sips of water to remove taste frommouth. In general no treatment is necessary unless large quantities are swallowed, however, get medical advice.If vomiting occurs spontaneously, keep head below hips to prevent aspiration.

Wash with soap and water before eating, drinking, smoking, applying cosmetics, or using toilet facilities. Laundercontaminated clothing before reuse. Contaminated leather articles including shoes cannot be decontaminatedand should be destroyed to prevent reuse. Keep containers closed when not in use. Store in a rool, dr;." placf"with adequate ventilation. Keep away from open flames and high temperatures.

Exposure Controlssure controls are ordinarii re uired under normal conditions of use.

Personal Protective E ui ment

Eye Protection:Chemical goggles, if liquid contact is likely, or Safety glasses

Skin Protection:Use protective clothing which is chemical resistant to this material. Selection of protective clothing depends onpotential exposure conditions and may include gloves, boots, suits and other items. The selection(s) should takeinto account such factors as job task, type of exposure and durability requirements.

Published literature, test data and/or glove and clothing manufacturers indicate protection is provided by:Butyl, or EVAL-Laminate

Appearance & Odor: Clear viscous liquid.

REACTNITY AN D

Stability:Material is stable under normal conditions.

Conditions to Avoid:Avoid high temperatures

Acute ToxicitMaterial Tested EffectsBADGE Resin Dermal -LD50

EPON@ Resin 828 MSDS# 23 Page 3 of 5 -

Storage:Avoid contact with hot liquid to prevent thermal burns.

Respiratory Protection:No respiratory protection is ordinarily required under normal conditions of use.

Materials to Avoid:Can react vigourously with strong oxidizing agents, strong Lewis or mineral acids, and strong mineral and organicbases. Avoid contact with water or liquids. Do not allow molten material to contact water or liquids as this cancause violent eruptions, splatter hot material, or ignite flammable material. Reaction with some curing agents mayproduce considerable heat and possible violent decomposition.

BADGE Resin Oral -LD50

Eye ~;:ritatio~:Dr ..'ze -2 [Rabbit]

Skin Irritation:Draize -1.6 [Rabbit]

Carcinogenicity:Recent 2-year bioassays in rats and mice exposed by the dermal route to the diglycidyl ether of bisphenol A(BADGE) yielded no evidence of carcinogenicity to the skin or any other organs. This study clarifies priorequivocal results from a 2-year mouse skin painting study, which were suggestive, but not conclusive, for weakcarcinogenic activity. Note: BADGE is a component in all BPA/ECH based liquid epoxy resins.

The International Agency for Research on Cancer (IARC) concluded that digylcidyl ether of bis-phenol A is notclassifiable as a carcinogen (IARC group 3), that is human and animal evidence of carcinogenicity is inadequate.

CarcinoQenicitv ClassificationChemical Name NTP IARC ACGIH

!

OSHA Table Z

I BADGE Resin Group 3-NotClassifiable

Mutagenicity:Resins of this type, liquid resins based on diglycidly ether of bisphenol A, have proved to be inactive when testedby in vivo mutagenicity assays. These resins have shown activity in in vitro microbial mutagenicity screening andhave produced chromosomal aberrations in cultured rat liver cells. The significance of these tests to man isunknown.

This section will be updated as ecological reviews are completed.

General Recommendations:If this material becomes a waste, it would not be a hazardous waste by RCRA criteria (40 CFR 261). Place in anappropriate disposal facility in compliance with local regulations.

~

US Department of Transportation Classification:This material is not subject to DOT regulations under 49 CFR Parts 171-180.

International Air Transportation Association Classification:This material is not classified as hazardous under lATA regulations.

The regulatory information provided is not intended to be comprehensiveregulations may apply to this material.

Other federal, state and local

I Federal Regulatory Status I

International Maritime Organization:This material is not classified as hazardous under IMO regulations.

Superfund Amendment & Reauthorization Act (SARA) Title III:

SARA Hazard Categories(311/312):Delayed (Chronic) Health Hazard.

Toxic Substances Control Act (TSCA) Inventory Status:This material is listed on the EPA TSCA Inventory of Chemical Substances.

I State Regulatory Status I

The following chemicals are specifically listed by individual states; other product specific health and safety data inother sections of the MSDS may also be applicable for state requirements. For details on your regulatoryrequirements you should contact the appropriate agency in your state.

California Safe Drinking Water and Toxic Enforcement Act (Proposition 65):Phenyl glycidyl ether (122-60-1 ) CA_65 C

CA_65 C = The chemical identified with this code is known to the state of California to cause cancer.

Product Codes: K122F, K122K

The information contained herein is based on data considered accurate. However, no warranty is expressed orimplied regarding the accuracy of these data or the results to be obtained from the use thereof.

27258-10680-101 R-12/21/2000

READ AND UNDERSTAND MATERIAL SAFETY DATA SHEET BEFORE HANDUNG OR DISPOSINGOF PRODUCT

PRODUCT CODE AND NAME : JAD230 JEFFAMIN~ D-230ISSUE DA TE 5/21/2001MSDS CD DA TE 1/1/2002

1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

MATERIAL IDENTITY

PRODUCT CODE AND NAME

JAD230 JEFF AMINE- Dm230

Chemical Name and/or Family or Description:

Polyoxypropylenediamine

COMPANY INFORMA nON

Huntsman Petrochemical CorporationP.O. Box 27707Houston, TX 77227-7707

TELEPHONE NUMBERSTransportation Emergency

Company: (409) 727-0831CHEMTREC: (BOO) 424-9300

Medical Emergency: (409) 722-9673 (24 Hour)General MSDS Assistance: (713) 235-6432Technical Information: (512) 459-6543

2. COMPOSITION AND INFORM A TION ON INGREDIENTS

THE CRITERIA FOR LISTING COMPONENTS IN THE COMPOSITION SECTION ARE AS FOLLOWS: CARCINOGENS ARE LISTED WHENPRESENT AT 0.1 % OR GREATER; COMPONENTS WHICH ARE OTHERWISE HAZARDOUS ACCORDING TO OSHA ARE LISTED WHENPRESENT AT 1.0 % OR GREATER; NON.HAZARDOUS COMPONENTS ARE LISTED AT 3.0 % OR GREATER. THIS IS NOT INTENDEDTO BE COMPLETE COMPOSITIONAL DISCLOSURE. REFER TO SECTION 14 FOR APPLICABLE STATES' RIGHT TO KNOW ANDOTHER REGULATORY INFORMATION.Product and/or Component(s) Carcinogenic According to:

OSHA IARC NTP OTHER NONE X

Range in %

100.00

Composition:

Chemical Name CAS Number Exposure Limits

Poly( oxy(methyl-1 ,2-ethanediyl».alpha-(2- 9046-10-0am i nomethylethyl)omega-(2 -aminomethylethoxy)-

THIS PRODUCT IS CONSIDERED HAZARDOUS ACCORDING TO OSHA (1910.1200).

1

PRODUqT CObE AND NAMEISSUE DA TE

MSDS CD DA TECOMPANY

JAD230 JEFFAMIN£iI D-2305/21/20011/1/2002HUNTSMAN

3. HAZARD IDENTIFICA TION

EMERGENCY OVERVIEW

Appearance:Colorless to slightly yellow liquid with a slight haze

Odor:

Ammonia-like

WARNING STATEMENT

CORROSIVE -CAUSES EYE AND SKIN BURNSHARMFUL OR FATAL IF SWALLOVVEDASPIRATION HAZARD IF SWALLOVVED-

CAN ENTER LUNGS AND CAUSE DAMAGECAUSES RESPIRATORY TRACT IRRITATION AND CAN CAUSE DAMAGE

DANGER

Hazardous MaterialInfonnation System(United States)

National Fire ProtectionAssociation NFP A(United States) Health

POTENTIAL HEALTH EFFECTS

Primary Route of Exposure

Eye X Skin X Inhalation X ingestion

Effects of Overexposure

Acute:

Inhalation:

Ingestion:

Sensitization Properties:

Causes irritation, experienced as pain, with excess blinking and tear production, and seen asextreme redness and swelling of the eye and chemical burns of the eye. Severe eye damagemay cause blindness.

Causes severe irritation with pain, severe excess redness and swelling with chemical burns,blister formation, and possible tissue destruction. Other than the potential skin irritationeffects noted above, acute (short term) adverse effects are not expected from brief skincontact; see other effects, below, and Section 11 for information regarding potential long termeffects.

Vapors or mist, especially as generated from heating the material or as from exposure inpoorly ventilated areas or confined spaces, are irritating and cause nasal discharge,coughing, and discomfort in nose and throat. Prolonged or repeated overexposure may resultin lung damage.

Causes burning of mouth, throat, and stomach with abdominal and chest pain, nausea,vomiting, diarrhea, thirst, weakness, and collapse. Aspiration may occur during swallowing orvomiting, resulting in lung damage.This product is not expected to be a human skin sensitizer based on animal data.

Chronic:Repeated skin contact may cause a persistent irritation or dermatitis. Repeated inhalation may cause lung damage.

Medical Conditions Aggravated by Exposure:

Skin contact may aggravate an existing dermatitis (skin condition). Overexposure to vapor, dust or mist may aggravateexisting respiratory conditions, such as asthma, bronchitis, and inflammatory or fibrotic respiratory disease.

2

PRODUC7:CODEANDNAMEISSUE DA TEMSDS CD DA TECOMPANY

JAD230 JEFFAM1N~ D-2305/21/20011/1/2002HUNTSMAN

Other Remarks:

This product contains one or more amines which may produce temporary and reversible hazy or blurred vision. Symptomsdisappear when exposure is terminated.

4. FIRST AID MEASURES

Eyes:Immediately flush eyes with large amounts of running water for at least 15 minutes. Hold eyelids apart while flushing to rinse entire

surface of eye and lids with water. Do not attempt to neutralize with chemical agents. Obtain medical attention immediately. Continueflushing for an additional 15 minutes if medical attention is not immediately available.

Skin:

Immediately remove contaminated clothing and shoes. Under a safety shower, flush skin thoroughly with large amounts of runningwater for at least 15 minutes. Do not attempt to neutralize with chemical agents. Get medical attention immediately. Discard ordecontaminate clothing and shoes before reuse.

Ingestion:If person is conscious and can swallow, immediately give two glasses of water (16 oz.), but do not induce vomiting. This material is

corrosive. If vomiting occurs, give fluids again. Have a physician determine if condition of patient will permit induction of vomiting orevacuation of stomach. Do not give anything by mouth to an unconscious or convulsing person.

Inhalation:

If inhaled, remove to fresh air. If not breathing or in respiratory distress, clear person's airway and start artificial respiration. VVith aphysician's advice, give supplemental oxygen using a bag-valve mask or manually triggered oxygen supply.

Other Instructions:

Swallowing of this corrosive material may result in severe ulceration, inflammation, and possible perforation of the upperalimentary tract, with hemorrhage and fluid loss. Aspiration of this product during induced emesis can result in severe lunginjury. If evacuation of stomach is necessary, use method least likely to cause aspiration, such as gastric lavage afterendotracheal intubation. Contact a Poison Control Center for additional treatment information.

5. FIRE-FIGHTING MEASURES

Ignition Temperature -AIT (degrees C):

Not determined.

Flash Point (degrees C):

121.1 (250°F) (PMCC)

Flammable Limits % (Lower-Upper):

Lower: Not determined.Upper: Not determined.

Recommended Fire Extinguishing Agents And Special Procedures:

Use water spray, dry chemical, foam or carbon dioxide to extinguish flames. Use water spray to cool fire-exposed containers. Wateror foam may cause frothing.

Unusual or Explosive Hazards:

None

Special Protective Equipment for Firefighters:

Wear special chemical protective clothing and positive pressure self-contained breathing apparatus. Approach fire from upwind toavoid hazardous vapors and toxic decomposition products. Decontaminate or discard any clothing that may contain chemical residues.

3

PRODUCT.CODE AND NAMEISSUE DA TEMSDS CD DA TECOMPANY

: JAD230 JEFFAMIN~ D-230: 5/21/2001: 1/1/2002:

HUNTSMAN

6. ACCIDENTAL RELEASE MEASURES (Transportation Spills: CHEMTREC (800)424-9300).

Procedures in Case of Accidental Release, Breakage or Leakage:

Ventilate area. Avoid breathing vapor. Wear appropriate personal protective equipment, including appropriate respiratory protection.Contain spill if possible. Wipe up or absorb on suitable material and shovel up. Prevent entry into sewers and waterways. Avoidcontact with skin, eyes or clothing.

7. HANDLING AND STORAGE

Precautions to be Taken in

Handling:

Minimum feasible handling temperatures should be maintained. Eye wash and safety shower should be available nearby when thisproduct is handled or used.

Storage:Periods of exposure to high temperatures should be minimized. Water contamination should be avoided. If stored above 1 OO"F, a

nitrogen atmosphere is recommended.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Protective Equipment (Type)

Eye/Face Protection:

Avoid eye contact. Chemical type goggles with face shield must be worn. Do not wear contact lenses.

Skin Protection:

Protective clothing such as coveralls or lab coats should be worn. launder or dry-clean when soiled. Gloves resistant to chemicalsand petroleum distillates required. Wlen handling large quantities, impervious suits, gloves, and rubber boots must be worn.Remove and dry-clean or launder clothing soaked or soiled with this material before reuse. Dry cleaning of contaminated clothing may

be more effective than normal laundering. Inform individuals responsible for cleaning of potential hazards associated with handlingcontaminated clothing.

Respiratory Protection:

Airborne concentrations should be kept to lowest levels possible. If vapor, mist or dust is generated and the occupationalexposure limit of the product, or any component of the product, is exceeded, use appropriate NIOSH approved air purifying orair supplied respirator after determining the airborne concentration of the contaminant. Air supplied respirators should alwaysbe worn when airborne concentration of the contaminant or oxygen content is unknown.

Ventilation:

Local exhaust ventilation recommended if generating vapor, dust, or mist. If exhaust ventilation is not available or inadequate, useNIOSH approved respirator as appropriate.

Exposure Limit for the Total Product:

None established for product.

9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance:Colorless to slightly yellow liquid with a slight haze

Odor:Ammonia-like

4

PRODUC1;-CODEANDNAMEISSUE DA TEMSDS CD DATECOMPANY

JA0230 JEFFAMIN~ 0-2305/21/2001

1/1/2002HUNTSMAN

Boiling Point (degrees C):

260 (500.F)

Melting/Freezing Point (degrees C):

Not determined.

Specific Gravity (water=l):0.948 @ 20/20.C

pH:11.7 (5% aqueous)

Vapor Pressure:

1 mmHg at 100°C (212°F)

Viscosity:9.5 cSt at 25"C (77"F)

VOC Content:

25% by ASTM D 2369

Vapor Density (Air:!):>1

Solubility in Water (%):

>10

Otller:None

10. STABILITY AND REACTIVITY

This Material Reacts Violently With:

Air Water Heat Strong Oxidizers Others X None of these

Comments:

This material reacts violently with acids.

Products Evolved When Subjected to Heat or Combustion:

Toxic levels of ammonia, combustion products of nitrogen, carbon monoxide, carbon dioxide, irritating aldehydes and ketones may beformed on burning in a limited air supply.

Hazardous Polymerizations:

DO NOT OCCUR

11. TOXICOLOGICAL INFORM A TION

TOXICOLOGICAL INFORMATION (ANIMAL TOXICITY DATA)

Oral:lD50 2.88 g/kg (rat) slightly toxicDermal:LD50 2.98 g/kg (rabbit) practically non-toxic

Inhalation:Not determined.

IRRITATION INDEX, ESTIMATION OF IRRITATION (SPECIES)

5

JAD230 JEFFAM/N~ D.230

5/21/20011/1/2002HUNTSMAN

PROD.UC1; C9DE AND NAMEISSUE DA TEMSDS CD DATECOMPANY

Eyes:(Draize) Believed to be > 80.00 -110.00/110 (rabbit) extremely irritating

Skin:(Draize) Believed to be > 6.50 -8.00 /8.0 (rabbit) corrosive

Sensitization:(Buehler) Negative -skin (guinea pig)

Other:

None

12. DISPOSAL CONSIDERATIONS:

Waste Disposal Methods:This product has been evaluated for RCRA characteristics and does not meet the criteria of a hazardous waste if discarded in its

purchased form. Under RCRA, it is the responsibility of the user of the product to determine at the time of disposal, whether theproduct meets RCRA criteria for hazardous waste. This is because product uses, transformations, mixtures, processes, etc. mayrender the resulting materials hazardous.

Remarks:

None

13. TRANSPORT INFORM A TION

TransportationDOT:

Proper Shipping Name:Amines, liquid, corrosive, n.o.s. (polyoxypropylene diamine)

Hazard Class:Class 8: Corrosive material

Identification Number:UN2735

Packing Group:III

Label Required:Class 8: Corrosive

IMDGProper Shipping Name:AMINES. LIQUID, CORROSIVE. N.O.S. (polyoxypropylene diamine)

Hazard ClassClass 8

Identification NumberUN2735

Packing GroupIII

Label RequiredClass 8 -Corrosive substances

ICAOProper Shipping Name:

6

PRODUCT c.ODE AND NAMEISSUE DA TEMSDSCDDATECOMPANY

JAD230 JEFFAMIN~ D.2305/21/20011/1/2002HUNTSMAN

Amines, liquid, corrosive, n.o.s. (polyoxypropylene diamine)

Hazard ClassClass 8

Identification NumberUN2735

Packing GroupIII

Label RequiredClass 8 -Corrosive

TDG

Proper Shipping Name:Corrosive liquid, n.o.s. (polyoxypropylene diamine)

Hazard Class:8

Identification Number:UN1760

Packing Group:III

Label Required:Corrosive

14. REGULA TORY INFORM A TION

Federal Regulations:

SARA Title III:

Section 302/304 Extremely Hazardous Substances

Chemical NameNone.

CAS Number Range in % TPQ RQ

Section 311 Hazardous Categorization:

Acute X Chronic Fire Pressure

Section 313 Toxic Chemical

Chemical NameNone.

Reactive N/A

CAS Number Concentration

CERCLAI

ChemicalNone.

CAS Number Range in % RQ

States Right-to-Know Regulations:

Chemical Name

None.

State Right-to-know

State list: CT (Connecticut), FL (Florida), IL (Illinois), MI (Michigan), LA (Louisiana), MA(Massachusetts), NJ (New Jersey), PA (pennsylvania), RI (Rhode Island)

California Prop. 65:The following detectable components of this product are substances, or belong to classes of substances, known to the State ofCalifornia to cause cancer and/or reproductive toxicity.

7

02(a)mOT

Name

HazardousSubstances:

JAD230 JEFFAMIN~ D-230

5/21/20011/1/2002HUNTSMAN

PRODUt:T GODE AND NAME

ISSUE DATEMSDS CD DATE

COMPANY

CAS NumberChemical NameNone.

INTERNATIONAL REGULAllONS:

TSCA Inventory Status:

This product, or its components, are listed on or are exempt from the Toxic Substance Control Act (TSCA) Chemical Substance

Inventory.WHMIS Classification:

Class E: Corrosive

Canadian Inventory Status:This product, or its components, are listed on or are exempt from the Canadian Domestic Substance List (DSL).

EINECS Inventory Status:This product, or its components, are listed on or are exempt from the European Inventory of Existing Chemical Substances (EINECS) orthe European List of Notified Chemical Substances (ELlNCS).

Australian Inventory Status:This product, or its components, are listed on or are exempt from the Australian Inventory of Chemical Substances (AICS).

Japan Inventory Status:This product, or its components, are listed on or are exempt from the Japan Ministry of International Trade and Industry (MITI)

inventory.

15. ENVIRONMENTAL INFORMA TION

Aquatic Toxicity:Not determined.

Mobility:Not determined.

Persistence and Biodegradability:

Not determined.

Potential to Bioaccumulate:

Not determined.

Remarks:

None

16. OTHER INFORMATION 5/21/2001

The following sections have been revised: 3,9. 13None

Supercedes: 1/13/1999

Print Date: 12/18/2001

8

PRODUCT C;ODE AND NAME

ISSUE "ATEMSDS CD DA TE

COMPANY

JAD230 JEFFAM/NE'" D-230

5/21/20011/1/2002HUNTSMAN

mE INFORMATION IN THIS DATA SHEET IS PROVIDED INDEPENDENTLY OF ANY SALE OF THE PRODUCT. IT IS PROVIDEDFOR THE PURPOSE OF HAZARD COMMUNICATION AS PART OF HUNTSMAN'S PRODUCT SAFETY PROGRAM. IT IS INTENDEDONLY AS A GUWE TO THE APPROPRIATE PRECAUTIONARY HANDLING OF THE PRODUCT BY A PROPERLY TRAINED PERSON.YOU ARE ENCOURAGED AND REQUESTED TO ADVISE THOSE WHO MAY COME IN CONTACT WITH SUCH PRODUCTS OF THEINFORMATION CONTAINED HEREIN. THE DATA RELATES ONLY TO THE SPECIFIC PRODUCT DESIGNATED, AND DOES NOTRELATE TO USE OF THE PRODUCT IN COMBINATION WITH ANY OTHER MATERIAL OR USE OF THE PRODUCT IN ANYPROCESS. THE DATA IS NOT INTENDED TO CONSTITUTE PERFORMANCE INFORMATION CONCERNING THE PRODUCT. NOEXPRESS WARRANTY, OR IMPLIED WARRANTY OF MERCHANTABILITY FOR FITNESS FOR A PARTICULAR PURPOSE IS MADEWITH RESPECT TO THE PRODUCT, ITS COMPOSITION, ITS SAFETY OR THE INFORMATION CONTAINED IN THIS DATA SHEET.

TO DETERMINE THE APPLICABILITY OR THE EFFECTS OF ANY LA W OR REGULATION WITH RESPECT TO THE PRODUCT,THE USER SHOULD CONSULT A LEGAL ADVISOR OR THE APPROPRIATE GOVERNMENT AGENCY. HUNTSMAN DOES NOTUNDERTAKE TO FURNISH ADVICE ON SUCH MATTERS.

CURRENT DATA SHEETS ARE AVAILABLE FOR ALL HUNTSMAN PRODUCTS. YOU ARE URGED TO OBTAIN DATA SHEETS FORALL HUNTSMAN PRODUCTS YOU BUY, USE OR DISTRIBUTE BY CALLING (713) 235-6432 OR DIRECTING YOUR INQUIRIES TO:

HUNTSMANCOORDINATOR, PRODUCT SAFETYP.O. Box 27707HOUSTON, TX77227-7707

NO PERSON OR ORGANIZATION EXCEPT A DULY AUTHORIZED HUNTSMAN EMPLOYEE IS AUTHORIZED TO PROVIDE ORMAKE AVAILABLE DATA SHEETS FOR HUNTSMAN PRODUCTS. DATA SHEETS FROM UNAUTHORIZED SOURCES MAYCONTAIN INFORMATION THAT IS NO LONGER CURRENT OR ACCURATE. NO PART OF THIS DATA SHEET MAY BEREPRODUCED OR TRANSMTITED IN ANY FORM, OR BY ANY MEANS, WITHOUT PERMISSION IN WRITING FROM HUNTSMAN.ALL REQUESTS FOR PERMISSION TO REPRODUCE MATERIAL FROM THIS DATA SHEET SHOULD BE DIRECTED TOHUNTSMAN, COORDINATOR, PRODUCT SAFETY AT THE ABOVE ADDRESS.

COPYRIGHT @ 2001 BY HUNTSMAN CORPORATION. ALL RIGHTS RESERVED.