Material Pumps PARTS LIST · 21010-00 nylon washer 4 21011-00 standoff 4 21014-00 round handle 2...
Transcript of Material Pumps PARTS LIST · 21010-00 nylon washer 4 21011-00 standoff 4 21014-00 round handle 2...
PA
RT
S LI
STGuardian VR-SeriesMaterial Pumps
Section 1 General Information
1:0 Technical Information ......................................................................................................................................... 11:1 Assembly Drawings ........................................................................................................................................... 51:2 Sub Assembly Drawings .................................................................................................................................... 161:3 Maintenance ....................................................................................................................................................... 29
Section 2 Technical & Warranty Information
2:1 Notes .................................................................................................................................................................. 302:2 Limited Warranty Policy ............................................................................................................ 322:3 Technical Assistance ................................................................................................................ 33For Your Reference ............................................................................................. INSIDE BACK COVER
N/A = Non Applicable
Table Of Contents
1
Section 1 - General Information: Technical Information
Sec.
1:0 VR Material Pump Technical Information
A5-6000 VR A5-12000 VR A7-6000 VR A7-12000 VR
Fluid Sections1.0 (18175-01)1.5 (19975-01)2.0 (19950-01)
1 (22350-00)2 (22370-00) 3 (20366-01)
Pneumatic Motor 5in. 5in. 7in. 7in.
Maximum / MinimumFluid Section Displacement
1.01.5 See #23860-5XX2.0
(21270-00) (22102-00) See #23860-7XX(20366-00)
Maximum Pump Stroke Length 3.1in. / 7.9 cm 5.36in. / 13.6 cm 5.36in. / 13.6 cm
Minimum Pump Stroke Length 1.21in. / 3. cm 2.12in. / 5.4 cm 2.12in. / 5.4 cm
Air Requirement at maximum output
30 cycle min. = 20 cfm/60 cycle min. = 41 cfm @ 100 psi
30 cycle min. = 71 cfm/60 cycle min. = 143 cfm @ 100 psi
Summery Sheet23860-7XX Output PSI Ratio Range21000-7XX GPC CC’s PC
711 0.084 318.662 2500 1:1 - 2.53:1
712 0.070 267.000 3000 .59:1 - 3.69:1
713 0.090 370.000 2000 .53:1 - 3.31:1
722 0.057 215.720 3200 1:1 - 2.53:1
723 0.080 319.000 2500 .78:1 - 4.88:1
733 0.111 421.603 1850 1:1 - 2.53:1
23860-5XX Output PSI Ratio Range20290-5XX GPC CC’s PC
511 0.033 125 3200 1:1 - 2.6:1
512 0.024 93.75 3200 2:1 - 5.2:1
513 0.021 83.3 3200 3:1 - 7.8:1
2
Section 1 - General Information: Technical Information
Sec.
1:0 VR Material Pump Technical Information
(XXX
XX-7
12) 1
.5:1
& 1
:1G
PCC
CPC
Max
O
utpu
t:0.
0726
7
TYP
PSI:
1740
2125
0-00
2127
0-00
B-S
ide
A-S
ide
10.
950.
90.
850.
80.
750.
70.
660.
60.
550.
50.
450.
4
10.
677
0.71
30.
752
0.79
60.
846
0.90
30.
960
1.02
61.
128
1.23
11.
354
1.50
51.
693
0.95
0.64
30.
677
0.71
50.
757
0.80
40.
858
0.91
20.
974
1.07
21.
169
1.28
61.
429
1.60
8
0.9
0.60
90.
641
0.67
70.
717
0.76
20.
812
0.86
40.
923
1.01
61.
108
1.21
91.
354
1.52
4
0.85
0.57
50.
606
0.63
90.
677
0.71
90.
767
0.81
60.
872
0.95
91.
046
1.15
11.
279
1.43
9
0.8
0.54
20.
570
0.60
20.
637
0.67
70.
722
0.76
80.
821
0.90
30.
985
1.08
31.
204
1.35
4
0.75
0.50
80.
534
0.56
40.
597
0.63
50.
677
0.72
00.
769
0.84
60.
923
1.01
61.
128
1.27
0
0.7
0.47
70.
502
0.53
00.
561
0.59
70.
636
0.67
70.
723
0.79
60.
868
0.95
51.
061
1.19
3
0.66
0.44
70.
470
0.49
60.
526
0.55
90.
596
0.63
40.
677
0.74
50.
812
0.89
40.
993
1.11
7
0.6
0.40
60.
428
0.45
10.
478
0.50
80.
542
0.57
60.
615
0.67
70.
739
0.81
20.
903
1.01
6
0.55
0.37
20.
392
0.41
40.
438
0.46
50.
496
0.52
80.
564
0.62
10.
677
0.74
50.
827
0.93
1
0.5
0.33
80.
356
0.37
60.
398
0.42
30.
451
0.48
00.
513
0.56
40.
615
0.67
70.
752
0.84
6
0.45
0.30
50.
321
0.33
80.
358
0.38
10.
406
0.43
20.
461
0.50
80.
554
0.60
90.
677
0.76
2
0.4
0.27
10.
285
0.30
10.
318
0.33
80.
361
0.38
40.
410
0.45
10.
492
0.54
20.
602
0.67
7
2127
0-00
3.29
03.
126
2.96
12.
797
2.63
22.
468
2.32
02.
172
1.97
41.
809
1.64
51.
480
1.31
6
2125
0-00
4.86
14.
618
4.37
44.
131
3.88
83.
645
3.42
73.
208
2.91
62.
673
2.43
02.
187
1.94
4
3
Section 1 - General Information: Technical Information
Sec.
1:0 VR Material Pump Technical Information
(XXX
XX-7
13) 2
:1 &
1.5
:1G
PCC
CPC
Max
O
utpu
t:0.
0937
0
TYP
PSI:
1260
2036
6-01
2125
0-00
B-S
ide
A-S
ide
10.
950.
90.
850.
80.
750.
70.
660.
60.
550.
50.
450.
4
10.
756
0.79
60.
840
0.88
90.
945
1.00
81.
072
1.14
51.
260
1.37
41.
512
1.68
01.
890
0.95
0.71
80.
756
0.79
80.
845
0.89
80.
957
1.01
91.
088
1.19
71.
306
1.43
61.
596
1.79
6
0.9
0.68
00.
716
0.75
60.
800
0.85
00.
907
0.96
51.
031
1.13
41.
237
1.36
11.
512
1.70
1
0.85
0.64
20.
676
0.71
40.
756
0.80
30.
857
0.91
10.
973
1.07
11.
168
1.28
51.
428
1.60
7
0.8
0.60
50.
636
0.67
20.
711
0.75
60.
806
0.85
80.
916
1.00
81.
100
1.21
01.
344
1.51
2
0.75
0.56
70.
597
0.63
00.
667
0.70
90.
756
0.80
40.
859
0.94
51.
031
1.13
41.
260
1.41
7
0.7
0.53
30.
561
0.59
20.
627
0.66
60.
711
0.75
60.
807
0.88
80.
969
1.06
61.
184
1.33
2
0.66
0.49
90.
525
0.55
40.
587
0.62
40.
665
0.70
80.
756
0.83
20.
907
0.99
81.
109
1.24
7
0.6
0.45
30.
477
0.50
40.
533
0.56
70.
605
0.64
30.
687
0.75
60.
825
0.90
71.
008
1.13
4
0.55
0.41
60.
438
0.46
20.
489
0.52
00.
554
0.59
00.
630
0.69
30.
756
0.83
10.
924
1.03
9
0.5
0.37
80.
398
0.42
00.
445
0.47
20.
504
0.53
60.
572
0.63
00.
687
0.75
60.
840
0.94
5
0.45
0.34
00.
358
0.37
80.
400
0.42
50.
453
0.48
20.
515
0.56
70.
618
0.68
00.
756
0.85
0
0.4
0.30
20.
318
0.33
60.
356
0.37
80.
403
0.42
90.
458
0.50
40.
550
0.60
50.
672
0.75
6
2125
0-00
4.86
14.
618
4.37
44.
131
3.88
83.
645
3.42
73.
208
2.91
62.
673
2.43
02.
187
1.94
4
2036
6-01
6.43
16.
109
5.78
85.
466
5.14
44.
823
4.53
44.
244
3.85
83.
536
3.21
52.
893
2.57
2
4
Section 1 - General Information: Technical Information
Sec.
1:0 VR Material Pump Technical Information
(XXX
XX-7
23) 2
:1 &
1:1
GPC
CC
PCM
ax
Out
put:
0.08
319
TYP
PSI:
1460
2036
6-00
2127
0-00
B-S
ide
A-S
ide
10.
950.
90.
850.
80.
750.
70.
660.
60.
550.
50.
450.
4
10.
512
0.53
90.
569
0.60
20.
640
0.68
20.
726
0.77
50.
853
0.93
01.
024
1.13
71.
280
0.95
0.48
60.
512
0.54
00.
572
0.60
80.
648
0.68
90.
736
0.81
00.
884
0.97
21.
080
1.21
6
0.9
0.46
00.
485
0.51
20.
542
0.57
60.
614
0.65
30.
698
0.76
80.
837
0.92
11.
024
1.15
2
0.85
0.43
50.
458
0.48
30.
512
0.54
40.
580
0.61
70.
659
0.72
50.
791
0.87
00.
967
1.08
8
0.8
0.40
90.
431
0.45
50.
482
0.51
20.
546
0.58
10.
620
0.68
20.
744
0.81
90.
910
1.02
4
0.75
0.38
40.
404
0.42
60.
451
0.48
00.
512
0.54
40.
581
0.64
00.
698
0.76
80.
853
0.96
0
0.7
0.36
10.
380
0.40
10.
424
0.45
10.
481
0.51
20.
547
0.60
10.
656
0.72
20.
802
0.90
2
0.66
0.33
80.
355
0.37
50.
397
0.42
20.
450
0.47
90.
512
0.56
30.
614
0.67
60.
751
0.84
5
0.6
0.30
70.
323
0.34
10.
361
0.38
40.
409
0.43
50.
465
0.51
20.
558
0.61
40.
682
0.76
8
0.55
0.28
10.
296
0.31
30.
331
0.35
20.
375
0.39
90.
426
0.46
90.
512
0.56
30.
625
0.70
4
0.5
0.25
60.
269
0.28
40.
301
0.32
00.
341
0.36
30.
388
0.42
60.
465
0.51
20.
569
0.64
0
0.45
0.23
00.
242
0.25
60.
271
0.28
80.
307
0.32
70.
349
0.38
40.
419
0.46
00.
512
0.57
6
0.4
0.20
50.
215
0.22
70.
241
0.25
60.
273
0.29
00.
310
0.34
10.
372
0.40
90.
455
0.51
2
Section 1 - General Information: Assembly Drawings
5REVISION A
Sec.
1:1 23860-7XX Big VR Material Pump Assembly
6
Sec.
1:1
Section 1 - General Information: Assembly Drawings
REVISION A
23860-7XX Big VR Material Pump Assembly
7
Sec.
1:1
Section 1 - General Information: Assembly Drawings
REVISION A
23860-7XX Big VR Material Pump Assembly
8
Sec.
1:1
Section 1 - General Information: Assembly Drawings
REVISION A
23860-7XX Big VR Material Pump Assembly
9
Sec.
1:1
Section 1 - General Information: Assembly Drawings
REVISION A
23860-7XX Big VR Material Pump Assembly
Part Number Description Qty.
16028-01 HITCH PIN 6
16028-03 HITCH PIN 4
1625-02 PIPE PLUG 1
18318-02 AIR GAUGE 1
19814-08 CLEVIS PIN 2
19814-09 CLEVIS PIN 2
19814-10 CLEVIS PIN 4
19814-11 CLEVIS PIN 2
20053-12C SCREW 3
20084-03 WASHER 4
20084-04 WASHER 4
20084-05 WASHER 4
20221-00 BALL VALVE 1
20296-00 PINCH POINT DECAL 4
20368-00 SWIVEL CASTER 4
20735-01 ELBOW FITTING 1
20735-03 ELBOW FITTING 1
20735-03 ELBOW FITTING 1
20895-00 CABLE 6
21001-00 V.R. FRAME 1
21002-00 YOKE & GUIDE ROD 1
21003-00 DRIVE LINK 2
21004-00 PUMP ADAPTER 2
21005-00 PIVOT BRACKET 2
21006-00 LINKAGE GUARD 1
21007-00 MOUNTING BRACKET 1
21008-00 ADJUSTMENT SCREW 2
21009-00 SHAFT COLLAR 10
21010-00 NYLON WASHER 4
21011-00 STANDOFF 4
21014-00 ROUND HANDLE 2
21021-00 RIGHT CALIBRATION DECAL 2
21022-00 LEFT CALIBRATION DECAL 2
21023-00 HAND WHEEL 2
21024-00 LIMIT SWITCH 1
21025-00 HANDLE 2
21027-00 STUD 2
21053-02 WASHER 4
21232-00 EXHAUST SILENCER 2
21291-00 POPPET VALVE 1
21308-40C SCREW 4
21340-02 AIR HOSE 1
Part Number Description Qty.
21395-00 REGULATOR 1
21666-00 BALL VALVE 1
21925-00 PILOT VALVE 1
22069-00 SPACER 2
22086-04 RETRACT SWITCH KIT 1
22310-00 AIR MOTOR 1
22312-00 VARIABLE RATIO DECAL 1
2253-01 LUBE FITTING 6
2253-02 LUBE FITTING 1
22956-00 HOLE COVER 1
23487-01 ELECTRICAL PLUG 1
23862-00 CONNECTION KIT 1
3344-07 FITTING 2
3800-08 COPPER WIRE
6792-05 COUPLE FITTING 2
7486-04 WASHER 4
7486-05 FENDER WASHER 4
7486-07 WASHER 3
7486-13 WASHER 4
7486-28 WASHER 2
7733-32 HEX NUT 1
7733-42 HEX NUT 8
7734-04 LOCK WASHER 4
7734-06 LOCK WASHER 10
7734-10 LOCK WASHER 8
7734-15 LOCK WASHER 1
7959-24F SCREW 2
8115-02 FITTING 1
8212-16F SCREW 4
8301-08C SCREW 2
8462-10 FITTING 1
8462-11 FITTING 2
8560-11 FITTING 2
9944-24C SCREW 4
9955-208C SCREW 4
RS-141-02 CORD GRIP 1
10
Sec.
1:1
Section 1 - General Information: Assembly Drawings
REVISION A
23860-5XX Small VR Material Pump Assembly
11
Section 1 - General Information: Assembly Drawings
REVISION A
23860-5XX Small VR Material Pump Assembly
Sec.
1:1
12
Section 1 - General Information: Assembly Drawings
REVISION A
23860-5XX Small VR Material Pump Assembly
Sec.
1:1
13
Section 1 - General Information: Assembly Drawings
REVISION A
23860-5XX Small VR Material Pump Assembly
Sec.
1:1
14
Section 1 - General Information: Assembly Drawings
REVISION A
23860-5XX Small VR Material Pump Assembly
Sec.
1:1
Part Number Description Qty.
16028-01 HITCH PIN 10
18154-00 PIVOT BRACKET 2
18158-00 PUMP ADAPTER 2
1880-00 ADAPTER FITTING 1
19814-04 CLEVIS PIN 6
19814-06 CLEVIS PIN 4
20084-02 WASHER 12
20221-00 BALL VALVE 1
20291-00 V.R. FRAME 1
20292-00 GUIDE ROD&YOKE 1
20293-00 DRIVE LINK 2
20296-00 PINCH POINT DECAL 2
20368-00 SWIVEL CASTER 4
20735-01 ELBOW FITTING 1
20735-08 ELBOW FITTING 3
20895-00 CABLE 6
21007-00 MOUNTING BRACKET 1
21024-00 LIMIT SWITCH 1
21308-40C SCREW 4
21585-01 SOLVENT VALVE 1
22042-00 LINKAGE GUARD 1
22054-00 HANDLE 2
22086-04 RETRACT SWITCH KIT 1
22312-00 VARIABLE RATIO DECAL 1
2253-02 LUBE FITTING 1
22807-00 AIR-ACTUATED VALVE 1
23487-01 ELECTRICAL PLUG 1
23861-00 CONNECTION KIT 1
4342-01 ELBOW FITTING 1
4342-04 ELBOW FITTING 2
6792-13 FITTING 1
7486-03 WASHER 2
7486-05 WASHER 4
7486-14 WASHER 4
15
Section 1 - General Information: Assembly Drawings
REVISION A
23860-5XX Small VR Material Pump Assembly
Sec.
1:1
Part Number Description Qty.
7729-10 HEX NUT 4
7730-12F SCREW 4
7733-08 HEX NUT 2
7733-34 HEX NUT 4
7733-40 HEX NUT 1
7733-42 HEX NUT 4
7734-03 LOCK WASHER 8
7734-04 LOCK WASHER 6
7734-06 LOCK WASHER 6
7734-10 LOCK WASHER 4
7735-12C SCREW 8
7783-48C SCREW 2
7818-22 DOWEL PIN 2
7959-24F SCREW 2
8115-03 FITTING 1
8115-04 FITTING 1
9672-12 FITTING 1
AM-500-01 AIR MOTOR 1
P33-19 EXHAUST SILENCER 2
RS-141-02 CORD GRIP 1
16
Sec.
1:1
REVISION D
22350-00 Fluid Section Assembly
Section 1 - General Information: Sub Assembly Drawings
17REVISION D
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
22350-00 Fluid Section Parts List
Part Number Description Qty.
1005-26 SNAP RING 1
13867-30 O-RING 1
13867-56 O-RING 3
19633-00 COMPRESSION SPRING 1
20448-00 TIE ROD 4
20484-48C SCREW 4
21255-01 SUPPORT WASHER 1
21256-00 PUMP HEAD 1
21257-00 PUMP CYLINDER 1
21258-00 PUMP SHAFT 1
21260-00 SPRING 1
21261-00 SST BALL 1
21263-00 PISTON GUIDE 1
21264-00 TRANSFER HOUSING SEAT 1
21265-00 FOOT VALVE BALL HOUSING 1
21267-00 FOOT VALVE SEAT 1
21268-00 PUMP BASE 1
21269-00 FOOT VALVE BALL 1
21327-01 ELBOW FITTING 1
21397-01 SHAFT EXTENSION 1
21555-00 LOWER PUMP SEAL 1
21556-00 UPPER PUMP SEAL 1
21557-00 TRANSFER HOUSING 1
21731-00 SOLVENT CUP ADAPTER 1
21896-03 PACKING RETAINER 1
21897-03 FELT WIPER 4
7733-43 HEX NUT 4
7734-08 LOCK WASHER 8
7959-24F SCREW 1
8560-05 FITTING 1
8560-07 FITTING 1
Repair Kit - 21277-00Part
Number Description Qty.
13867-14 O-RING 2
13867-30 O-RING 1
13867-56 O-RING 3
21263-00 GUIDE 1
21555-00 LOWER PUMP SEAL 1
21556-00 UPPER PUMP SEAL 1
21897-03 FELT WIPER 4
18REVISION B
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
22370-00 Fluid Section Assembly
REVISION B19
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
22370-00 Fluid Section Parts ListPart
Number Description Qty.
1005-02 SNAP RING 1
13867-43 O-RING 3
13867-44 O-RING 1
18219-00 PUMP CYLINDER 1
18227-00 PUMP HEAD 1
18289-00 TIE ROD 4
18295-01 UPPER SUPPORT WASHER 1
19633-00 COMPRESSION SPRING 1
19634-00 VALVE,FOOT HOUSING 1
21271-00 PUMP BASE 1
21327-01 ELBOW FITTING 1
21397-01 SHAFT EXTENSION 1
21440-00 SOLVENT CUP ADAPTER 1
21595-00 PUMP SEAL 2
21597-00 TRANSFER HOUSING 1
21598-00 TRANSFER SEAT HOUSING 1
21599-00 PUMP SHAFT 1
21896-01 PACKING RETAINER 1
21897-01 FELT WIPER 4
7733-17 HEX NUT 4
7734-07 LOCK WASHER 4
7734-12 LOCK WASHER 4
7959-24F SCREW 1
8560-04 FITTING 1
8560-07 FITTING 1
9945-48C SCREW 4
APS-119 FOOT VALVE SEAT 1
APS-128 CHROME BALL 1
APS-133 SST BALL 1
FS-110 PISTON GUIDE 1
P33-16 REDUCING FITTING 1
SM-1430 PARTS LIST 1
Repair Kit - 21845-00Part
Number Description Qty.
FS-110 PISTON GUIDE 1
13867-43 O-RING 3
13867-44 O-RING 1
21595-00 PUMP SEAL 2
21896-01 PACKING RETAINER 1
21897-01 FELT WIPER 4
20REVISION A
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
20366-01 Fluid Section Assembly
21REVISION A
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
20366-01 Fluid Section Parts List
Part Number Description Qty.
13867-14 O-RING 1
13867-57 O-RING 1
13867-58 O-RING 2
20443-00 PISTON GUIDE 1
20444-00 TRANSFER HOUSING SEAT 1
20445-00 FOOT VALVE BALL 1
20447-00 FOOT VALVE SEAT 1
20448-00 TIE ROD 4
20450-00 PUMP HEAD 1
20451-01 PUMP BASE 1
20452-00 PUMP SHAFT 1
20453-00 FOOT VALVE BALL HOUSING 1
20454-00 PUMP CYLINDER 1
20484-48C SCREW 4
20494-00 SPRING 1
21255-02 UPPER SUPPORT WASHER 1
21327-01 ELBOW FITTING 1
21397-01 SHAFT EXTENSION 1
21713-00 COMPRESSION SPRING 1
22194-00 SOLVENT CUP & SEAL HOUSING 1
22197-00 UPPER PUMP SEAL 1
22198-00 TRANSFER HOUSING 1
22199-00 LOWER PUMP SEAL 1
7733-43 HEX NUT 4
7734-08 LOCK WASHER 8
7959-24F SCREW 1
8560-05 FITTING 1
8560-07 FITTING 1
APS-128 CHROME BALL 1
Repair Kit - 22196-00Part
Number Description Qty.
20443-00 PISTON GUIDE 1
13867-57 O-RING 1
13867-58 O-RING 2
22197-00 UPPER PUMP SEAL 1
22199-00 LOWER PUMP SEAL 1
22REVISION K
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
18175-01 Fluid Section Assembly
23REVISION K
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
18175-01 Fluid Section Parts List
Part Number Description Qty.
APS-119 FOOT VALVE SEAT 1
APS-128 CHROME BALL 1
APS-133 SST BALL 1
FS-110 PISTON GUIDE 1
UF-118 FOOT VALVE HOUSING 1
1005-02 SNAP RING 1
13867-43 O-RING 3
13867-44 O-RING 1
18215-00 PUMP BASE 1
18219-00 PUMP CYLINDER 1
18227-00 PUMP HEAD 1
18289-00 TIE ROD 4
18295-01 UPPER SUPPORT WASHER 1
20295-00 SHAFT EXTENSION 1
21440-00 SOLVENT CUP ADAPTER 1
21595-00 PUMP SEAL 2
21597-00 TRANSFER HOUSING 1
21598-00 TRANSFER HOUSING SEAT 1
21599-00 PUMP SHAFT 1
21803-00 COMPRESSION SPRING 1
21896-01 PACKING RETAINER 1
21897-01 FELT WIPER 4
2594-43 ROLL PIN 1
7733-17 HEX NUT 4
7734-07 LOCK WASHER 4
7734-12 LOCK WASHER 4
9943-16F SCREW 1
9945-32C SCREW 4
Repair Kit - 21845-00Part
Number Description Qty.
FS-110 PISTON GUIDE 1
13867-43 O-RING 3
13867-44 O-RING 1
21595-00 PUMP SEAL 2
21896-01 PACKING RETAINER 1
21897-01 FELT WIPER 4
24REVISION E
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
19975-01 Fluid Section Assembly
25REVISION E
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
19975-01 Fluid Section Parts List
Part Number Description Qty.
APS-119 FOOT VALVE SEAT 1
APS-128 CHROME BALL 1
P33-14 SOLVENT CUP 1
UF-118 FOOT VALVE HOUSING 1
13867-43 O-RING 4
13867-44 O-RING 1
18215-00 PUMP BASE 1
18227-00 PUMP HEAD 1
18289-00 TIE ROD 4
18295-03 UPPER SUPPORT WASHER 1
19839-02 SST BALL 1
19956-00 PUMP CYLINDER 1
19960-00 TRANSFER HOUSING SEAT 1
19961-00 PUMP SHAFT END 1
21716-00 TRANSFER HOUSING 1
21717-00 PUMP SHAFT 1
21718-00 SOLVENT CUP ADAPTER 1
21719-00 PISTON GUIDE 1
21720-00 UPPPER PUMP SEAL 1
21725-00 LOWER PUMP SEAL 1
2594-43 ROLL PIN 1
7733-17 HEX NUT 4
7734-07 LOCK WASHER 4
7734-12 LOCK WASHER 4
9943-16F SCREW 1
9945-32C SCREW 4
Repair Kit - 22052-00Part
Number Description Qty.
21719-00 PISTON GUIDE 1
13867-43 O-RING 4
13867-44 O-RING 1
21720-00 UPPER PUMP SEAL 1
21725-00 LOWER PUMP SEAL 1
26REVISION F
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
19950-01 Fluid Section Assembly
27REVISION F
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
19950-01 Fluid Section Parts List
Part Number Description Qty.
APS-119 FOOT VALVE SEAT 1
APS-128 CHROME BALL 1
P33-14 SOLVENT CUP 1
UF-118 FOOT VALVE HOUSING 1
13867-43 O-RING 4
13867-44 O-RING 1
18215-00 PUMP BASE 1
18227-00 PUMP HEAD 1
18289-00 TIE ROD 4
19901-00 SST BALL 1
19904-00 TRANSFER SEAT 1
19949-00 PUMP CYLINDER 1
19961-00 PUMP SHAFT END 1
21591-00 PUMP SEAL 2
21592-00 TRANSFER HOUSING SEAL 1
21593-00 SOLVENT CUP ADAPTER 1
21594-00 PUMP SHAFT 1
21699-00 PISTON GUIDE 1
21726-00 SUPPORT WASHER 1
2594-43 ROLL PIN 1
7733-17 HEX NUT 4
7734-07 LOCK WASHER 4
7734-12 LOCK WASHER 4
9943-16F SCREW 1
9945-32C SCREW 4
Repair Kit - 22053-00Part
Number Description Qty.
21699-00 PISTON GUIDE 1
13867-43 O-RING 4
13867-44 O-RING 1
21591-00 PUMP SEAL 2
28
Sec.
1:2
Section 1 - General Information: Sub Assembly Drawings
AM-500 Air Motor Assembly
29
Fluid Section Maintenance & Overhaul Procedure
Daily Routine Maintenance 1. Visually inspect the system for leaks.
2. Check desiccant dryer beads to insure they are still purple and have not changed to pink. 3. Check and lube top of the fluid section.
Wipe off residual material and add a tablespoon of DOP,DBP
Weekly Maintenance 1. Place a small amount of grease on the air motor shaft.
2. See related manuals.
Sec.
1:3
Section 1 - General Information: Maintenance
30
Section 4 - Technical & Warranty Information: Notes
Sec.
2:1
31
Section 2 - Technical & Warranty Information: Notes
Sec.
2:1
GLASCRAFT, INC. (“GlasCraft”) warrants to the original Purchaser of GlasCraft manufactured equipment and parts, that all GlasCraft manufactured equipment and parts will conform to their published written specifications and be free of defects in workmanship and material for a period of one (1) year from the original date of installation. GlasCraft makes no warranty to anyone other than the original Purchaser.
If any GlasCraft manufactured part or equipment is found to be defective in workmanship or material within the one-year period from the date of installation, as determined solely by GlasCraft, GlasCraft, in its sole discretion, will either repair or replace the defective part or equipment at GlasCraft’s cost, including freight charges both ways, or credit or refund the purchase price for the defective equipment or part.
A warranty claim will be honored only when:
1. GlasCraft has been informed, in writing, of any such defect in workmanship or material within ten (10) days after discovery by the original Purchaser;
2. An official of GlasCraft has issued a return authorization number; and
3. The claimed defective equipment or part has been returned to GlasCraft by the original Purchaser, freight prepaid (with proper return authorization number(s) attached), to: GlasCraft, Inc., 5845 West 82nd Street, Suite 102, Indianapolis, IN 46278, U.S.A.
This warranty shall not apply to any equipment or parts that have been altered or repaired by anyone other than GlasCraft or to defects or damage resulting from improper installation, misuse, negligence, accident, or use not specified by GlasCraft. This warranty shall not apply to any equipment where any parts or components were replaced by any parts or components not manufactured or supplied by GlasCraft. The decision by GlasCraft shall be conclusive and binding on Purchaser.
GlasCraft does not warrant that any equipment or parts sold to Purchaser meet or comply with any local, state, federal, or other jurisdiction’s regulations or codes. GlasCraft does not warrant that any equipment or part sold to Purchaser,
when used individually or in concert with any other part, equipment, device, component or process, does not infringe on any patent rights of any third party. GlasCraft only warrants that it has no specific knowledge of any such infringement.
GlasCraft makes no warranty as to any parts or equipment manufactured by others. Purchaser shall look solely and only to the manufacturer of such parts or equipment with respect to any warranty claims. GlasCraft hereby assigns to Purchaser the original manufacturer’s warranties to all such equipment and parts, to the full extent permitted.
THE AFORESAID WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IM-PLIED. SPECIFICALLY THERE ARE NO WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH WARRANTIES ARE SPECIFICALLY DISCLAIMED.
GlasCraft shall not be liable for any loss or expense resulting from damage or accidents caused by improper use or ap-plication of materials manufactured or sold by GlasCraft or its distributors or agents.
UNDER NO CIRCUMSTANCES SHALL GLASCRAFT’S LIABILITY EXCEED THE AMOUNT PUR-CHASER PAID FOR THE CLAIMED DEFECTIVE EQUIPMENT OR PART. UNDER NO CIRCUM-STANCES SHALL GLASCRAFT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAM-AGES OR FOR LOST PROFITS.
No action arising from or relating to any goods manufactured by or purchased from GlasCraft may be brought more than one (1) year after the cause of action accrues.
Section 2 - Technical & Warranty Information: Limited Warranty Policy
Sec.
2:2
32
33
Section 2 - Technical & Warranty Information: Technical Assistance............
Thank You for selecting GlasCraft spray equipment
Should you have any questions or need technical assistance, contact your factory authorized GlasCraft distributor.
Distributor: _________________________
Phone: ____________________________
Contact: ___________________________
For any issues your distributor cannot address, the GlasCraft technical service department is always available to assist you with the operation of your spray equipment. To help our technical representatives expedite your call and better address your questions, please have the following information ready and available when you phone GlasCraft.
* If your questions are not urgent, You can e-mail all correspondence to [email protected]
Model: _____________________________ Air compressor size: __________________ Compressor to system supply line: _______ Spray gun: __________________________ Serial number: _______________________ Pressure at the system: _______________ Material pump: _______________________ Main air line volume: __________________ Serial number: _______________________ System gauge pressures Catalyst pump: _______________________ AAC pressure: _____________________ Chopper: ____________________________ Serial number: _______________________ Atomizing air pressure: ________________ (external mix) Type of material: ______________________ Material pump pressure: _______________ Type of catalyst: ______________________ Solvent flush pressure: ________________ Catalyst percentage: __________________
Sec.
2:3
Quality and Performance…GENUINE GLASCRAFT
www.glascraft.com
SM-1431REVISION March 2008
5845 WEST 82nd STREETINDIANAPOLIS, INDIANA 46278 U.S.A.
Phone (317) 875-5592Fax (317) 875-5456E-Mail [email protected]