MASTERBATCHES AND COMPOUNDS - PolyFiller · MASTERBATCHES AND COMPOUNDS 1 SECURITY FORM: 2....
Transcript of MASTERBATCHES AND COMPOUNDS - PolyFiller · MASTERBATCHES AND COMPOUNDS 1 SECURITY FORM: 2....
MASTERBATCHES AND COMPOUNDS
1
SECURITY FORM:
2. Composition / information on ingredients
3. Identification of hazards
Use of the product
Product code
Product name PE Filler Master Batch
F 35
use as filler for plastic processes such as extrusion, blow molding, film, yarn, stamping, injection, tubes, plates, etc.
1. Chemical identification of the product
Composition of the material Ingredients Composition(% w/w)
CaCO3 80
LLDPE
Additive
Percentage of hazardous ingredients This product contains no hazardous ingredients
18
2
Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - [email protected] - tel.+ 39 0382766373
Product hazard This product contains no hazardous ingredientsIt is not classified as dangerous.
health risk
environmental risk
Not risk
Not risk
MASTERBATCHES AND COMPOUNDS
2
SECURITY FORM:
4. First aid measures
5. Fire-fighting measures
6. Measures in the event of accidental spillage
7. Manipulation/Storage
Accidental exposure
Inhalation
contact with the skin
Contact with eyes
Ingestion
Rinse immediately with water, seek medical advice.
No effect after use, but wash your hands with soap and water
Solutions
Move to fresh air if discomfort persists, consult a doctor
Sciacquare la bocca. Consultare il medico
Recommended extinguishing media Avoid areas of high temperature and sparks Electric
Special precautions Do not release contaminated water into drains or surface waters
Special protective equipment Respiratory drive recommended
Procedures for the issuance or pour out Take up mechanically and collect in a suitable container. Dispose of according to local regulations.Do not release contaminated water into drains or surface waters
Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - [email protected] - tel.+ 39 0382766373
Manipulation managed according to good industry practiceprevent the formation of dust and spillage of the product.
Storage Store in tight containers in a dry, cool and windy. Keep away from strong oxidizing agents and sources of heat.
MASTERBATCHES AND COMPOUNDS
3
SECURITY FORM:
9. Chemical and physical properties
Cleaning the workplace
Personal protection:
Eyes protection
Hand Protection
Follow the good practice of good industrial hygien
Utilize gloves approved
Wear glasses
8. Personal protection / exposure control
Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - [email protected] - tel.+ 39 0382766373
Appearance look
Odor
Physical state
Steam pressure / temperature
Boiling Point
Melting point
Degree of liquefaction (190°C/5Kg)
Evaporation rate
Viscosity
Solubility in water
Flammability
Explosive properties
White granule
Odorless
Solid
Not evaluable
Not evaluable
105 - 115 deg.C
23g/10 mins
Not evaluable
Not evaluable
Insoluble
Fuel
Not explosive
MASTERBATCHES AND COMPOUNDS
4
SECURITY FORM:
10. Stability and reactivity
11. Toxicological information
Conditions to avoid
Material to avoid
Hazardous decomposition products
Hazardous polymerization
Avoid exposure to open flame or high temperature
Avoid contact with strong oxidizing agents
Thermal decomposition puàò release carbon dioxide, mono oxides or nitrogen oxides.
Not polymerize
Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - [email protected] - tel.+ 39 0382766373
Effects of exposure Short-term
Oral toxicity
Acute oral toxicity
Toxicity by inhalation
Effects exposure long-term
Irritation
Sensitization
Carcinogenic characteristics
Reproductive toxicity
Teratogenic
Mutagenesis
Toxicologically synergistic product name
Data not available
Data not available
Data not available
not irritable
Data not available
Data not available
Data not available
Data not available
Data not available
Data not available
MASTERBATCHES AND COMPOUNDS
5
SECURITY FORM:
13. Ecological considerations
14. Transportation information
12. Ecological considerations
Ecological information
Eco toxicity data
The release into the environment should be avoided. The product is not soluble in water.
No data are available on the toxicity to aquatic life or other microorganisms.
Waste / unused product
Icontaminated packaging Contaminated packaging contaminated packaging should betreated as the product
Incinerate or dispose of in accordance with local regulations
transportation information
Rail transport Free unrestricted
Air transport
Maritime transport Free unrestricted
Free unrestricted
Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - [email protected] - tel.+ 39 0382766373
MASTERBATCHES AND COMPOUNDS
6
SECURITY FORM:
15. Regulatory information
16. More Information
Regulatory information This product is suitable for food contact
reference for this document Technical details F35
Original
Date of preparation / revision
Revision number
Polyfiller - Via San Mauro snc - 27013 Chignolo Po (Pv) - www.polyfiller.eu - [email protected] - tel.+ 39 0382766373