MARVEL CROCHET CHAIR TOPPER - Spotlight Australia
Transcript of MARVEL CROCHET CHAIR TOPPER - Spotlight Australia
SHOW US WHAT YOU’RE MAKING
/spotlightstores
@spotlightstores
MARVEL CROCHET CHAIR TOPPERNº 13.19.24 PROJECT SHEET
MARVEL CROCHET CHAIR TOPPER
INTERMEDIATE
WHAT YOU’LL NEED• ‘4 Seasons’ Marvel 8ply and Marvel 8ply
Prints 100g balls: 1 x Main Colour (print) (M),1 x Contrast 1 (C1), 1 x Contrast 2 (C2), 1 x Contrast 3 (C3), 1 x Contrast 4 (C4), 1 x Contrast 5 (C5).
• 4mm crochet hook or size required to give correct tension
• Scissors, yarn needle, tape measure, stitch marker, sewing or safety pins
MEASUREMENTS
Woven Section (approx) cm 43 square
Edges (approx) cm 7.5 deep
TENSION
18 sts x 10 rows to 10cm over treble fabric using 4mm hook.
Note – This project is made by crocheting the individual strips and then weaving them together. The ends of the strips are then anchored by crocheting the edges along the strip ends.
INSTRUCTIONS
STRIPS
Using 4mm hook and M, make 79ch.
1st row – Miss 3ch, 1tr in next ch and each ch to end ...77 sts.
2nd row – 3ch (counts as 1tr throughout), 1tr in each st to end.
3rd row – Rep 2nd row until strip measures 43cm from beg. Fasten off.
Make a total of 6 strips in M and 4 strips each in C1, C2, C3 and C4 in same manner … 22 strips in all.
FIRST EDGE
Join C5 to end of one M strip and using 4mm hook, work 7dc evenly across end. Without breaking yarn, cont to work 7dc evenly across the ends of strips in the following order: C1, C2, C3, C4, M, C1, C2, C3, C4 and M, turn ...77 sts.
2nd row – 3ch, 1tr in each st across.
3rd – 7th rows – Rep 2nd row.
At end of 7th row, make 75ch. Place a stitch marker in last ch and set aside.
BEG TASSEL
Using M and piece of cardboard 10cm wide, make 30 wraps around cardboard. Cut along one edge to make a bundle of yarn about 20cm long.
Join To Tie – Remove stitch marker and reinsert hook into ch loop. Work a ch around centre of yarn bundle and pull tightly to secure.
8th row – Work 1dc in ch closest to tassel, then in each ch to end, 1dc in each tr of edge piece and then make 75ch. Make a second tassel (as before) and join to tie in the same way.
9th row – Work 1dc in ch closest to tassel and in each ch to end, sl st through top of first tr below dc row. Fasten off.
SECOND EDGE
Work as for first edge on opposite ends of strips, making sure the strips aren’t twisted or crossed over. Put aside.
THIRD EDGE
Join rem 11 strips as for first edge. Weave the loose ends of the strips under and over the strips of the first piece. Pin the ends of each strip to the last strip of the first piece to keep the strips in order.
The information on this project sheet is presented in good faith, but no warranty is given, nor results guaranteed. Quantities and selections may vary at each store. Copyright Spotlight 2018.
FOURTH EDGE
Using C5 and 4mm hook, work 7dc evenly across each rem strip end (removing the pins as you go) … 77sts. Finish in the same way as the other three edges.
FINISHING
DO NOT PRESS. Use lengths of M to complete tassels by winding and tying them firmly about 2cm below the join to the ties. Trim tassels.
Use C5 to catch the inner corners of the edges tog so the woven section is fastened in each corner. Sew in ends.
The information on this project sheet is presented in good faith, but no warranty is given, nor results guaranteed. Quantities and selections may vary at each store. Copyright Spotlight 2018.