MARK IV VERTICAL SLIDING DOOR REPLACEMENT PARTS...

ECN CS-2582 AFTER INSTALLING THE DOOR PLEASE FORWARD TO H4406581 Rev N JAMISON DOOR COMPANY THE MAINTENANCE DEPARTMENT OR OWNER. P/N H4406581

MARK IV VERTICAL SLIDING DOOR

REPLACEMENT PARTS BOOK

JAMISON DOOR COMPANY

P.O. BOX 70 HAGERSTOWN, MARYLAND 21740

1-800-532-3667 301-733-3100

INTERNET: http://www.JamisonDoor.com E-MAIL: [email protected]

http://www.jamisondoor.com/

ECN CS-2582 2 H4406581 Rev N

JAMISON DOOR COMPANY Phone: (USA & Canada) 1-800-532-3667 (Int.) 301-733-3100 P/N H4406581

THIS PAGE LEFT BLANK

ECN CS-2582 3 H4406581 Rev N


CONTENTS 1. ORDERING INSTRUCTIONS ........................................................................................................... 4

2. CABLE AND COUNTERWEIGHT ASSEMBLY ................................................................................ 5

3. CHAIN DRIVE AND SUPPORT SYSTEM ........................................................................................ 6

4. CHAIN LOCK ASSEMBLY ON DOOR (BUILT AFTER 1/2002) ........................................................ 7

5. CONTROL PANEL POWERTRON ON DOOR (BUILT BEFORE 1/2006) ........................................ 8

6. CONTROL PANEL POWERTRON (ON DOOR BUILT AFTER 1/2006) ......................................... 10

7. CONTROL PANEL POWERTRON 575 VOLT (ON DOOR BUILT AFTER 1/2006) ........................ 12

8. COUNTERWEIGHT BOX ............................................................................................................... 14

10. LIMIT SWITCH .............................................................................................................................. 18

11. LOCKING PROVISIONS............................................................................................................... 19

12. LOCKING PROVISIONS: CYLINDER AND BACK RELEASE ...................................................... 20

13. MISCELLANEOUS DOOR PARTS ............................................................................................... 21

14. PNEUMATIC REVERSING EDGE ASSEMBLY ........................................................................... 22

15. POWER UNIT ASSEMBLY ........................................................................................................... 24

16. JAMECO CONTROL BOX ............................................................................................................ 26

17. PULL CORD SWITCH .................................................................................................................. 28

18. ROLLERS AND BRACKETS ........................................................................................................ 29

19. SHEAVE ASSEMBLY: STANDARD ............................................................................................. 30

20. SHEAVE ASSEMBLY: STANDARD UPGRADED ........................................................................ 31

21. TOP LATCH ASSEMBLY .............................................................................................................. 32

22. TRACK .......................................................................................................................................... 33

22. DIN RAIL TERMINAL STRIPS (FOR CONTROL PANELS BUILT AFTER 10/09/2020) ............... 34

ECN CS-2582 4 H4406581 Rev N


1. ORDERING INSTRUCTIONS

ECN CS-2582 5 H4406581 Rev N


2. CABLE AND COUNTERWEIGHT ASSEMBLY

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 * Counterweight Assembly (Specify Total Door Weight) 4406-161 4406-161 2 Cable Clamp (3/16”) 204-306 2 ** Cable Clamp (5/16”) 204-312 3 ** Cable W/Terminal End for Counterweight Side Special 4 ** Cable W/Terminal End for Side W/O Counterweight Special 3&4 ** Pair Cables 4406-054-01 4406-054 5 Sleeve Nut 486-053 6 Lock Nut 752-205 7 Synthane Roller 931-010 8 Clevis Pin 754-211 9 Cotter Pin 754-303 10 Thimble 204-309 11 Additional Weight (1/4” 1.5 Pound) 4318-497-01 4318-497 12 Hex Head Bolt (1/2” X13) (Specify Length) Special * Specify Left Hand or Right Hand Counterweight and Total Door Weight Complete with Hardware and Gasket. ** Specify Width-in-Clear and Height-in-Clear, Referance shop order for correct diamitor and length.

Note: See instruction sheet for ordering parts.

ECN CS-2582 6 H4406581 Rev N


3. CHAIN DRIVE AND SUPPORT SYSTEM

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Lower spreader Angle 4406-063-01 4406-063 2* Lower spreader Angle Bracket 4406-182-## 4406-182 3 Lower Idler Base 4406-065-01 4406-065 4 Support Tube Subassembly 4406-064-01 4406-064 5* Support Tube Wall Bracket 4406-061-## 4406-061 6 Top Support Angle 4406-062-01 4406-062 7 Brass Washer (2-1/4” X 1-1/32” X .128”) 4406-067-23 4406-067 8 Idler Sprocket 4318-430-01 4318-430 9 Oilite Bearing (A-1149-1) 481-033 10 Steel Washer (1-3/4” X 13/32” X 1/8”) 753-022 11 Lockwasher (3/8” Medium Split) 753-503 12 Hex Head Machine Bolt (3/8”-16 X ¾”) 751-419 13 Hex Head Machine Bolt (3/8”-16 X 1-1/4”) 751-421 14 Locknut Hex (3/8” –16) 752-205 15 Steel Washer (13/16” X 13/32” X 13Ga.) 753-006 16 Machine Bolt (3/8”-16 X 2-3/4”) 751-427 17 Hex Nut (3/8”-16) 752-107 18 Drive Link 4370-255-01 4370-255 19 Connecting Link (2040 1” Pitch) 202-011 20 Drive Chain (#40-1/2” Pitch) 202-004 *Size will vary: Need to know Door thickness & with or without Wicket door


ECN CS-2582 7 H4406581 Rev N


4. CHAIN LOCK ASSEMBLY ON DOOR (BUILT AFTER 1/2002)

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Chain Lock Assembly 4406-067-01 4406-067 1 Chain Lock Mounting Bracket 4406-262-01 4406-262 2 Bolt, Taptite Washer Head (3/8”-16 x 1”) 769-102 3 Hex Nut (5/16”-18) 752-105 4 Screw, Pan Head (#8-18 x ¾”) 765-324 5 Chain Lock Spacers 4406-057-01 4406-057 6 Chain Lock Base 4404-046-01 4406-046 7 Bushing 191-163 8 Bushing Mounting Plate 4404-186-01 4404-186 9 Screw, Button Head (3/8”-16 x ¾”) 761-310 10 Chain Lock Guide Block 486-134 11 Cable 204-321 12 Cable Crimp 204-322 13 Machine Bolt (3/8”-16 x ½”) 751-425 14 Pull Ring (5/16 X 3”) 489-020 15 Guide Plate 4404-290-01 4404-290 16 Spring 482-029 17 Set Screw (1/4”-20 x5/8”) 767-119 18 Plunger 486-135


ECN CS-2582 8 H4406581 Rev N


5. CONTROL PANEL POWERTRON ON DOOR (BUILT BEFORE 1/2006)

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Control Panel Assy. (Give Model Number & Serial Numbers) (Specify NEMA 1, 3, 4, 4X or 12) 4390-238-XX 4390-238 *1 Housing – NEMA 3, 4 or 12 191-037 1 Housing – NEMA 1 486-117 1 Housing – NEMA 4X 191-040 2 Mounting Plate 4390-237-01 4390-237 3 Baffle 4390-122-01 4390-122 4 Transformer (240/480 Primary – 24 Volt Secondary) 115-106 5 Transformer (120/208/380 Primary – 24 Volt Secondary) 115-107 6 Fuse FNM-2 116-103 7 Reversing Contactor 111-037 8 Brass Cup Washer 753-905 9 Marker Strip 191-508 10 Terminal Strip 191-505 11 Stop Switch 113-108 12 Relay 111-029 13 Pilot Light (120V or 240V) 4290-073-01 4290-73 13 Pilot Light with Resister –(480V) 4290-073-03 4290-73 14 Time Delay 111-227 15 Termostst (80°) Optional 114-005 16 Heater (20 Watt) Optional 4369-044-01 4369-44 *17 Rubber Washer 11/16” X 9/32” X 1/16” 559-026 18 Self Tapping Screw #6-32 X 3/8” 765-303 19 Self Tapping Screw #6-32 X 1/2” 765-304 20 Self Tapping Screw #6-32 X 5/8” 765-305 21 Self Tapping Screw #8-32 X 3/8” 765-306 22 Round Head Machine Screw #10-32 X 3/8” 764-136 23 Self Tapping Screw #10-24 X 1/2” 765-310


ECN CS-2582 9 H4406581 Rev N



ECN CS-2582 10 H4406581 Rev N


6. CONTROL PANEL POWERTRON (ON DOOR BUILT AFTER 1/2006)

ECN CS-2582 11 H4406581 Rev N


Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Rev. Contactor 60 Hz. 111-037 3 4 Floor Loop Socket 11-Pins, Octal Style 111-049 5 Time Delay 111-227 4390-216 6 Switch, Stop 113-108 4390-138 7 Thermostat 114-005 4290-69 8 Transformer Class 2 115-109 4390-434 9 Fuse 3AG, 1/4 Amp 116-107 10 Fuse, 3 Amp FNQ-R-3 600 VAC 116-108 11 Counter ENM #E4B74D 119-013 12 Floor Loop Unit 326SF24A-7, Harness 802A-4 119-014 13 Radio Control Multi-Code 1090 119-015 14 End Stop 170-004 15 Fuse Block 2 Poles 191-166 16 Fuse Block 1 Pole 191-167 17 Grounding Lug 191-355 18 Terminal Blocks 2-142 191-501 19 Marker, Number 191-508 4390-231 20 Enclosure, NEMA 4 191-514 4395-197 21 Enclosure, NEMA 4x 191-515 4395-197 22* Terminal Block 8 Rowes 191-518 23 24 25 Enclosure, NEMA 1 486-204 4390-416 26 Base Plate #16 GA. x 11” x 11” 486-205 4390-423 27 Din Rail 35mm x 5.25” 4390-406-02 4390-406 28 Bracket, Fuse Block #16 GA. 4390-417-01 4390-417 29 Baffle Plate #16 GA. 4390-418-01 4390-418 30 Bracket #16 GA. 4390-420-01 4390-420 31 Retainer #16 GA. 4390-422-01 4390-422 32 Heater Assy. 50W.120V. 4390-426-01 4390-426 33 Pilot Light Assy. NEMA 1 120V / 240V 4390-432-01 4390-432 34 Pilot Light Assy. NEMA 1 480V 4390-432-02 4390-432 35 Pilot Light Assy. NEMA 4 480V (STD) 4390-433-01 4390-433 36 Pilot Light Assy. NEMA 4 240V 199-016 37 Grounding Wire, Control Panel 14 AWG 13” Lg. 4390-470-02 4390-470 38 Ferrule 9/16 O.D. x 5/16 I.D. x 7/16 931-011 4277-359 39 Rnd Hd Mach Screw #10-32 x 3/8” lg 764-136


Complete control panel assembly (active model numbers) (also specify nema 1, 4, or 4x) ▪ Standard speed…………………………………………… 4390-436-xx

Optional Kits Available

▪ Control Panel Heater…………………………………………….439044401 H4390-444 ▪ Gearbox and Motor Heater with Hardware……………………439504601 H4395-046 ▪ Gearbox and Motor Heater No Hardware……………………..439520401 H4395-204 ▪ Travel Limit Switch Heater………………………………………439511201 H4395-112 ▪ Floor Loop……………………………………………………….. H4390-425 ▪ Radio Control…………………………………………………… H4390-424 ▪ Time Delay ……………………………………………………… H4390-227

*FOR CONTROL PANELS SHIPPED AFTER 10/09/2020 SEE SECTION 22

ECN CS-2582 12 H4406581 Rev N


7. CONTROL PANEL POWERTRON 575 VOLT (ON DOOR BUILT AFTER 1/2006)

ECN CS-2582 13 H4406581 Rev N


Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Rev. Contactor 60 Hz. 111-037 3 4 Floor Loop Socket 11-Pins, Octal Style 111-049 5 Time Delay 111-227 4390-216 6 Switch, Stop 113-108 4390-138 7 Thermostat 114-005 4290-69 8 Transformer 575 Volts 115-113 9 Fuse 3AG, 1/4 Amp 116-107 10 Fuse, 3 Amp FNQ-R-3 600 VAC 116-108 11 Counter ENM #E4B74D 119-013 12 Floor Loop Unit 326SF24A-7, Harness 802A-4 119-014 13 Radio Control Multi-Code 1090 119-015 14 End Stop 170-004 15 Fuse Block 2 Poles 191-166 16 Fuse Block 1 Pole 191-167 17 Grounding Lug 191-355 18 Terminal Blocks 2-142 191-501 19 Marker, Number 191-508 4390-231 20 Enclosure, NEMA 4 191-514 4395-197 21 Enclosure, NEMA 4x 191-515 4395-197 22* Terminal Block 8 Rowes 191-518 23 24 25 Enclosure, NEMA 1 486-204 4390-416 26 Base Plate #16 GA. x 11” x 11” 486-205 4390-423 27 Din Rail 35mm x 5.25” 4390-406-02 4390-406 28 Bracket, Fuse Block #16 GA. 4390-417-01 4390-417 29 Baffle Plate #16 GA. 4390-418-01 4390-418 30 Bracket #16 GA. 4390-420-01 4390-420 31 Retainer #16 GA. 4390-422-01 4390-422 32 Heater Assy. 50W.120V. 4390-426-01 4390-426 33 34 Pilot Light Assy. NEMA 1 480V 4390-432-02 4390-432 35 Pilot Light Assy. NEMA 4 575V (STD) 4390-433-03 4390-433 36 Grounding Wire, Control Panel 14 AWG 13” Lg 4390-470-02 4390-470 37 Fuse Holder Din Rail Mtg. 170-020 38 Fuse FNM-3 3 Amp 116-105


Complete Control Panel Assembly (Active Model Numbers) (Also Specify NEMA 1, 4, or 4X) ▪ Standard Speed 575 Volt …………………………………………… 4390-457-XX

Optional Kits Available

▪ Control Panel Heater…………………………………………….439044401 H4390-444 ▪ Gearbox and Motor Heater with Hardware……………………439504601 H4395-046 ▪ Gearbox and Motor Heater No Hardware……………………..439520401 H4395-204 ▪ Travel Limit Switch Heater………………………………………439511201 H4395-112 ▪ Floor Loop……………………………………………………….. H4390-425 ▪ Radio Control…………………………………………………… H4390-424 ▪ Time Delay ……………………………………………………… H4390-227

*FOR CONTROL PANELS SHIPPED AFTER 10/09/2020 SEE SECTION 22

ECN CS-2582 14 H4406581 Rev N


8. COUNTERWEIGHT BOX

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1* Cover / Front 4406-163-XX 4406-163 2* Box / Rear 4406-163-XX 4406-163 3 Self Drill Screw (#8-18 X1/2”) 765-327

*Reference Numbers

(Prepainted) (Galvanized) Length Piece 1 Piece 2 Piece 1 Piece 2 6’0” 4406-163-21 XX 4406-163-31 XX 7’0” 4406-163-22 4406-163-01 4406-163-32 4406-163-11 8’0” 4406-163-23 4406-163-02 4406-163-33 4406-163-12 9’0” XX 4406-163-03 XX 4406-163-13 10’0” 4406-163-25 4406-163-04 4406-163-34 4406-163-14 *Please specify finish (galv, stainless, or pre-painted), the door model #, serial #, HIC, and left or right hand counterweight.


ECN CS-2582 15 H4406581 Rev N



ECN CS-2582 16 H4406581 Rev N


9. FRAME GASKET ASSEMBLY

ECN CS-2582 17 H4406581 Rev N


Ref # Group Finish Offset Name of Part Stock No. Drawing 1* Gasket Sub-Assembly Horiz. (White) 1* 5’0” 4404-010-01 4404-10 1* 6’0” 4404-010-02 4404-10 1* 7’0” 4404-010-03 4404-10 1* 8’0” 4404-010-04 4404-10 1* 9’0” 4404-010-05 4404-10 1* 10’0” 4404-010-06 4404-10 2* Gasket Sub-Assy. Vert. (White) (Specify Hand) 2* 6’0” 4404-010-11 4404-10 2* 7’0” 4404-010-12 4404-10 2* 8’0” 4404-010-13 4404-10 2* 9’0” 4404-010-14 4404-10 2* 10’0” 4404-010-15 4404-10 2* 12’0” 4404-010-16 4404-10 2* 14’0” 4404-010-17 4404-10 3* Gasket Retainer 3* SST 5’0” LH 4404-016-21 4404-16 3* SST 5’0” RH 4404-016-71 4404-16 3* SST 6’0” LH 4404-016-22 4404-16 3* SST 6’0” RH 4404-016-72 4404-16 3* SST 7’0” LH 4404-016-23 4404-16 3* SST 7’0” RH 4404-016-73 4404-16 3* SST 8’0” LH 4404-016-24 4404-16 3* SST 8’0” RH 4404-016-74 4404-16 3* SST 9’0” LH 4404-016-25 4404-16 3* SST 9’0” RH 4404-016-75 4404-16 3* SST 10’0” LH 4404-016-26 4404-16 3* SST 10’0” RH 4404-016-76 4404-16 3A Head Gasket Retainer (Order Reference 3, RH) 4 SST Pan Head Screw #14 x 2” 765-361 5* Gasket Outer Wrapper .04 x 5” 552-165 6* Flat Gasket Retainer for Doors w/Jambs (Not Shown) 4404-422-xx 4404-422 7 Screw (for Flat Gasket Retainer) 765-359 8 Gasket Heat Wire (Call Factory w/Serial Number) xxx-xxx *Please specify the HIC and WIC of the door that the item is to be used on.


ECN CS-2582 18 H4406581 Rev N


10. LIMIT SWITCH

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Complete Limit Switch Assy (NEMA 1) 4395-026-01 4395-026 Assy Complete Limit Switch Assy (NEMA 4) 4395-026-03 4395-026 1 Housing (NEMA 4) 4395-199-01 4395-199 1 Housing (NEMA 1) 486-118 1 Housing (NEMA 4X) 4395-199-02 4395-199 2 Label 995-423 3 Base 4395-012-01 4395-012 4 Limit Switch Mounting Block 934-003 5 Actuator Block 934-004 6 Flange Bearing 481-018 7 Pillow Block Bearing 481-250 8 Shaft 486-133 9 Sprocket (for HIC up to 12’) 4395-018-01 4395-018 9 Sprocket (for HIC over 12’) 4395-125-01 4395-125 10 * Gasket (NEMA 3,4,4X or 12) 4395-019-01 4395-019 11 * Gasket (NEMA 3,4,4X or 12) 4395-020-01 4395-020 12 Switch 113-009 13 Round Head Bolt (1/4”-20 X 6”) 764-137 15 Hex Head Bolt (1/4”-20 X ¾”) 751-402 16 Hex Lock Nut (1/4”-20) 752-203 17 Self Tapping Screw (6-32 X 1”) 765-102 18 Flat Washer (1/2” X 9/32” X 16 Ga.) 753-151 19 Rubber Mounting Plate 4395-124-01 4395-124 20 Flat Washer (5/8” X 9/32 X 16 Ga.) 753-002 21 Compression Spring 482-056 *Use No. 20 for Items 10 and 11 with NEMA 1.


ECN CS-2582 19 H4406581 Rev N


11. LOCKING PROVISIONS

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Manual Door Front Locking Sub-Assembly 4243-537-XX 4243-537 3 Pop Rivet (5/32” X 3/8”) 755-358 4A Eyebolt (Steel Doors Only) (Specify if Washer Required) 751-210 4B Eyebolt (Plastic Doors Only) (Specify if Washer and Nut Required) 751-213 5 Hasp Blade (Galvanized) 4243-490-01 4243-490 5 Hasp Blade (Chrome) 4243-490-02 4243-490 6 Cover Plate (with 1/2” hole) 4406-078-05 4406-078 7 Cam 4243-378-01 4243-378 8 Set Screw (Cup Point) (1/4’-20 X ¼” Lg.) 767-126 9 Switch 113-007 10 Machine Screw, Round Head (#6-32 X 1”) 764-102 11 Nut, Standard Hex (#6-32) 752-101 12 Screw (Type “F”, #10-24 NC X 1/2” Lg.) 765-318 13 Hasp Blade with Cam 4243-462-01 4243-462 14 Retaining Nut (Cooler) 4243-302-01 4243-302 14 Retaining Nut (Freezer) 4243-302-02 4243-302 15 Cover Plate (with 1-3/8” hole) 4406-078-04 4406-078 16 Staple Loop 486-112 17 Recessed Cup (without hole) 4038-008-01 4038-008 18 Galv Escutcheon 4243-352-01 4243-352 18 SST Escutcheon 4243-352-02 4243-352 19 Rivet (5/32 x 3/8”) 755-361 21 SST Tee Handle 4243-662-01 4243-662 22 SST Roll Pin (1/8” X 5/8”) 754-050 23 Shaft 931-001 ** Tee Handle Assembly (Items 21,22,23) (4” Door) 4243-644-01 4243-644


ECN CS-2582 20 H4406581 Rev N


12. LOCKING PROVISIONS: CYLINDER AND BACK RELEASE

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Front Handle Base (with Latch Plate Assembly) 4406-247-01 4406-247 3 Flat Washer (1-3/8” X 41/64” X 13 Ga.) 753-020 4 Front Escutcheon 4318-437-01 4318-437 5 Back Recessed Cup 4318-211-03 4318-211 6 Back Escutcheon 4318-052-01 4318-052 7 Thru Shaft (4” Door) 4406-245-01 4406-245 8 Back Handle Assembly 4318-547-01 4318-547 9 Roll Pin (3/16” X 7/8”) 754-006 10 Screw, Pan Head Type “F” #10-24 X ½”) 765-310 11 Rivet (5/32” x ¼” long) 755-365 12 Set Screw (Cup Point ¼-20 X ¼”) 767-126 13 Dead Lock Cylinder 483-049 14 Screw, Round Head Machine (#10-24 X 1”) 764-112 15 Shoulder Bolt (5/16” X ½”) 769-106


ECN CS-2582 21 H4406581 Rev N


13. MISCELLANEOUS DOOR PARTS

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Gasket Retainer 512-028 2 Gasket 512-037 3 Gasket End Plug 559-037 4 Screw 765-352 5 Door Stop (Power) 4406-438-01 4406-438 6 Screw, Pan Head (#6 X ½”) 765-108 7 Door Stop (Manual) 934-012 8 Taptite Bolt (1/4”-20 X 1”) 769-103 9 Screw (¼-20 X 1-1/4) 764-209 10 Alum Door Pull 251-010 10 Chr Door Pull 4038-001-02 4038-001 12 Rear Door Pull Cup (Optional) 4318-211-01 4318-211 13 Rear Door Pull Bar (Optional) 4038-029-01 4038-029 14 Pop Rivet (1/4” X 5/8”) 755-365 15 Pop Rivet (5/32” X 3/8”) 755-358 16 Spacer Block 559-040 17 Galv Screw, Sheet Metal 763-439 17 SST Screw, Sheet Metal 765-322 18 SST Hinge, 3” Butt 439-016


ECN CS-2582 22 H4406581 Rev N


14. PNEUMATIC REVERSING EDGE ASSEMBLY

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Pneumatic Reversing Edge Assembly Special 1 Gasket Insert (Width-in-Clear + 4”) 512-037 2 End Plugs H4409-237 4409-237 3 Hose (Width-in-Clear + 2-1/2”) 559-100 4 Vent Plug (Glue in place) 4390-166-01 4390-166 5 End Plug (Glue in place) 4390-167-01 4390-167 7 Air Duct 759-034 8 Hose (4” Long) 999-030 10 Gasket Retainer 512-028 11 Screw, Pan Head (#8-32 NC x 1/8” long) 765-307 12 Switch 113-113


ECN CS-2582 23 H4406581 Rev N



ECN CS-2582 24 H4406581 Rev N


15. POWER UNIT ASSEMBLY

ECN CS-2582 25 H4406581 Rev N


Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Gear Box 201-102 2 Collar 486-151 3 Roll Pin (3/16” X 2”) 754-010 4 Friction Disc 991-200 5 Sprocket Assembly 4395-056-01 4395-056 6 Tongued Disc 4395-008-01 4395-008 7 Spring 753-908 8 Retainer 4395-009-01 4395-009 9 Lock-washer Split (1/2”) 753-505 10 Machine Bolt (with Locktite) (1/2”-13 X 1-1/2”) 751-440 11 Mounting Plate 4395-028-01 4395-028 12 Motor (115/230 Volt 1 Phase) 133-308 12 Motor (208-230/460 Volt 3 Phase) 133-306 13 Key (1/8” X 1”) 4277-329-01 4277-329 14 Machine Bolt (3/8”-16 X 1”) 751-420 15 Lock-washer Split (3/8”) 753-503 16 Clip Angle 4395-027-01 4395-027 17 Rubber Grommet 559-029 18 Limit Switch Assembly (See Limit Switch Assy) XXX-XXX 19 Control Panel (See Control Panel) XXX-XXX 20 Support Angle 4318-519-01 4318-519 21 Machine Bolt (3/8”-16 X 1-1/2”) 751-422 22 Lock-nut, Hex (3/8”-16) 752-205 24 Machine Bolt (3/8”-16 X 2”) 751-422 25 Flat Washer (13/16” X 13/32” X 16 Ga.) 753-006 26 Machine Bolt (3/8”-16 X 2”) 751-424 27 Machine Bolt (1/4”-20 X ¾”) 751-402 28 Flat Washer (1-1/4” X 9/32 X 16 Ga.) 753-015 29 Lock-nut, Hex (1/4”-20) 752-203 30 Flat Washer (5/8” x 9/32” X 16 Ga.) 753-002 31 Rubber Washer (11/16” x 9/32” x 1/16”) 559-026 32 Limit Switch Chain (Specify Quantity) 202-004 33 Connecting Link (#40 ½” Pitch) 202-005


ECN CS-2582 26 H4406581 Rev N


16. JAMECO CONTROL BOX

ECN CS-2582 27 H4406581 Rev N


Ref # Group Finish Offset Name of Part Stock Stock No. No. Drawing 1 Toggle Switch 113118 2 Humidity based fan control 113119 3 Receptacle cover 113120 4 Wire SO18/3 123120 5 Fork Terminal 170067 6 Ring Terminal 170068 7 3C Compact Splice 170069 8 5C Compact Splice 170070 9 2-Gang Lug Box 191549 10 Liquidtight Cord Grip 191550

ECN CS-2582 28 H4406581 Rev N


17. PULL CORD SWITCH

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Complete WPS Switch Assembly (Without Heat) 113-218 Assy Complete WPS Switch Assembly (With Heat) 113-219 1 Pull Cord Rope W/ Tassel (Not Shown) 4285-059-02 4285-59 1 Pull Cord Rope Vinyl 60’ (Not Shown) 4285-049-01 4285-49


ECN CS-2582 29 H4406581 Rev N


18. ROLLERS AND BRACKETS

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Galv Bottom Roller Bracket 4406-222-01 4406-222 1 SST Bottom Roller Bracket 4406-257-01 4406-257 2 Galv Top Roller Bracket 4406-223-01 4406-223 2 SST Top Roller Bracket 4406-256-01 4406-256 3 Roller 481-067 4 ZN Taptite Washer Head Bolt (3/8”-16 X 1”) 769-102 4 SST Taptite Washer Head Bolt (3/8”-16 X 1”) S60678102 5 Galv Top Roller Bracket For Split Door 4406-295-01 4406-295 6 SST Top Roller Bracket For Split Door 4406-536-01 4406-536

Please specify the door model, serial #, and door thickness. Note: See instruction sheet for ordering parts.

ECN CS-2582 30 H4406581 Rev N


19. SHEAVE ASSEMBLY: STANDARD (Used on 4” Doors less then 96 sq ft / 400 bls. Or

on 6” Door less then 64 sq ft / 400 lbs.)

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Complete Assy with double groove sheave 4406-167-01 4406-167 Assy Complete Assy with single groove sheave 4406-168-01 4406-168 1 Base (Includes welded colar – 5/16”X18 set screw) 4406-166-01 4406-166 1A Shaft 4406-164-01 4406-164 2 Support Bracket 4406-015-01 4406-015 3 * Double Groove Sheave 205-018 4 ** Single Groove Sheave 4318-041-01 4318-041 5 Spacer 4406-016-01 4406-016 6 Washer –(2” od X 1-1/16” id X 9/64” Lock) 753-043 7 Needle Bearing 481-153 8 Door Stop 4406-018-01 4406-018 9 Machine Bolts (3/8” nc X 1-1/4” lg.) 751-421 10 Lock Nut (3/8” nc) 752-205 11 Grease Fitting (Alemite # 1641B) 489-026 12 Machine Bolts (3/8” X 1” lg.) 751-420 * Counterweight side ** Opposite counterweight side


ECN CS-2582 31 H4406581 Rev N


20. SHEAVE ASSEMBLY: STANDARD UPGRADED (Used On 4” Doors greater then 96 sq ft / 400 Lbs and less then 144 sq ft / 600 Lbs. Or

Use On 6” Door greater then 64 sq ft / 400 Lbs and less then 100 sq ft / 600 Lbs.)

Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Complete Assy W/Double Groove Sheave 4479-065-01 4479-065 Assy Complete Assy W/Single Groove Sheave 4479-064-01 4479-064 1 Hex Head Bolt (3/8-16 NC x 1) 751-420 2 Hex Head Nylock Nut (3/8-16 NC) 752-205 3 Zn Washer Flat (2 x 1-1/16 x 9/64) 753-043 4 Set Screw Dog Point (5/16-18 NC X 1-3/8) 767-304 5 Support Bracket 4406-015-01 4406-015 6 Spacer (1.315 OD x 1.049ID x 5/8 long) 4406-016-01 4406-016 7 Sheave Bracket Base 4406-166-01 4406-166 8 Shaft Assembly (1” dia) 4479-061-01 4479-061 9 Single Sheave Assy (6” PD) 4479-062-01 4479-062 10 Door Stop 4406-018-01 4406-018 11 Machine Bolts (3/8” NC X 1-1/4” lg.) 751-421 * Counterweight side ** Opposite counterweight side


ECN CS-2582 32 H4406581 Rev N


21. TOP LATCH ASSEMBLY

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Galv Latch Base 4319-018-01 1 Chr Latch Base 4319-018-02 2 Galv Latch Pawl (For 2” Thick Door) 4319-730-03 2 Chr Latch Pawl (For 2” Thick Door) 4319-730-04 2 Galv Latch Pawl (For 4” Thick Door) 4319-730-01 2 Chr Latch Pawl (For 4” Thick Door) 4319-730-02 2 Galv Latch Pawl (For 6” Thick Door) 4319-019-01 2 Chr Latch Pawl (For 6” Thick Door) 4319-019-02 3 Spring 482-032 4 SST Pivot Pin 754-221 5 Cotter Pin (1/8” X 1-1/4” Long) 754-307 6 Eye Bolt with Nut (5/16 X1”) 751-207 7 Sash Chain (No. 50) (H.I.C. minus 6’ 8”) 489-010 8 “S” Hook (3/16” X 1-1/2” Diameter) 489-022 9 Pull Ring (5/16 X 3” Diameter) 489-020 12 Tapetite Bolt (5/16”-18 NC x 1” Long) 759-105 12 SST Tapetite Bolt (5/16”-18 NC x 1” Long) 751-502 13 Galv Latch Strike Plate 4406-250-01 13 SST Latch Strike Plate 4406-250-02 14 Galv Taptite Bolt (3/8”-16 X 1”) 769-102 14 SST Taptite Bolt (3/8”-16 X 1”) 751-505 15 SST Flat Washer (7/8” x 13/32” x .062) 753-164 16 Galv Hex Head Type F Self Tapping Screw (1/4”-20 X ¾”) 765-402 16 SST Pan Head Machine Screw (1/4”-20 X ¾”) 765-332 17 Flat Washer 753-002 18 Eye Bolt with Nut 751-210


ECN CS-2582 33 H4406581 Rev N


22. TRACK

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 3” Track (Specify HIC) 4406-012-XX 4406-012 2 Track Support 4406-172-01 4406-172 3 Carriage Bolt (5/16”nc X ¾” long) 751-007 4 Washer (7/8” X 3/8” X 5/64”) 753-047 5 Lockwasher Shakeproof (5/16”) 753-403 6 Hex Nut (5/16”nc) 752-123 7 Track Bracket (For Split Doors) 4406-311-01 4406-311 8 Drop Loop Support Bracket (Power Doors) 4404-273-01 4404-273 9 Galv Cable Clamp (Single Wire) 4290-579-01 4290-579 9 Chr Cable Clamp (Single Wire) 4290-579-02 4290-579 9 Galv Cable Clamp (Double Wire) 4290-578-01 4290-578 9 Chr Cable Clamp (Single Wire) 4290-578-02 4290-578 10 Locknut (10-24) 752-202 11 Flat Washer (9/16” X ¼” X 18 Ga.) 753-001 12 Hex Head Machine Bolt (10-24 X 1”) 751-460


ECN CS-2582 34 H4406581 Rev N


22. DIN RAIL TERMINAL STRIPS (FOR CONTROL PANELS BUILT AFTER 10/09/2020)

NOTES:

1. Terminal #25 is unique to some door with the pedestrian open feature. 2. 2-Pin jumper may or may not be required depending on options ordered with door, please reference wiring

diagram to confirm.

Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 End Stop 170-004 2* 2-Pin Jumper 170-026 3* Terminal Block (Orange) 170030 4 Terminal Barrier, Block 170-048 5* Identification Tag 996-415 6 DIN Rail 4390-406-01 4390-406 7 Flat Washer, Qty 2 Req’d (Not Shown) 753-100 8 #8-32 x 3/8” PPH Screw, Qty 2 Req’d (Not Shown) 765-306

*When ordering, specify serial number Note: See instruction sheet for ordering parts.

MARK IV VERTICAL SLIDING DOOR REPLACEMENT PARTS...

Documents

Transcript of MARK IV VERTICAL SLIDING DOOR REPLACEMENT PARTS...