1

Contents1. intended use 2

2. warnings 2

3. tips 2

4. laser pointer warning 2

5. You have received 3

6. assembling and connecting 4

7. operation 7

8. technical specifications 9

9. sYstem requirements 11

10. maintenance 12

11. warrantY 12

12. ergonomical recommendations 12

13. declaration of conformitY 13

version: 1.1.2 | 2017-10-30

manual | TaGaRnO FHD zap

2

1. Read the manual before you use the product2. Use the product only as specified, or the protection supplied by the product can

be compromised3. If fluids are spilled on the product, turn the system off immediately by pulling the power

supply out of the electrical outlet4. In case of fire close to the microscope, please turn off and disconnect the system5. Do not touch the light source. It gets hot when using the product6. Do not look directly into the light source7. You must not discard this electrical/electronic product in domestic household waste

Please dispose at your local recycling centre8. Avoid subjecting the lens to sharp or hard objects9. Please do not connect the microscope, if visible damages appear10. When applicable connect the power plug to a grounded power outlet11. Do not dismantle any parts of the microscope, except where noted in the manual12. Never disassemble or clean internal optical surfaces13. Use only the power supply provided from TAGARNO14. Always turn off the system before unplugging, when possible

WARNINGS Read all safety information before you use the productPlease pay attention when you see the warning label on the product

The product is a digital magnifying system consisting of a camera unit, PCBs, mechanical parts and a power supply. The product is intended for marketing worldwide and is designed for manual visual inspection

INteNded uSe

Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take appropriate measures.

tIPS1. When applicable, use both hands to move the XY Table2. When applicable use both hands to adjust the height of the product3. Avoid touching the lens glass4. Place the microscope near a wall outlet where the plug can be easily unplugged

WARNING! Laser radiation when turned onPower must always be turned off during maintenanceUse the product only as specified or hazardous laser radiation exposure can occur

Radiation specifications:Class ll laser pointer with 1mW max output at 650-660nm.The label is placed on the product.

3. Tips

1. inTenDeD use

2. waRninGs

4. laseR pOinTeR waRninG

3

manual camera head power supply handles

5. YOu Have ReceiveD

XKeY control box

OpTiOns

angle bracket

4

mount the handles on the vesa bracket.

connect the power supply to the microscope

6. assemblinG anD cOnnecTinGassemblinG anD cOnnecTinG (1/3)

connect hdmi cable from the microscope to a monitor

5

esd

connect usb 3.0 cable from the microscope to a pc warning! do not connect the hdmi cable to a pc.

hdmi cable

assemblinG anD cOnnecTinG (2/3)

connect grounding cable to grounding point, to ensure esd of the microscope

6

connect the microscope to the XKeY control box. detach vesa mount and handles. mount the angle bracket to the microscope. several options.

assemblinG anD cOnnecTinG | OpTiOns (3/3)

7

short push switches between iris, gain and preset mode.

increase iris/gain or switch between zoom preset 1, 2 or 3.

decrease iris/gain or switch between zoom preset 1, 2 or 3.

to change and save a zoom preset, use zoom buttons to select a zoom level and simultaneously press left/right buttons. osd will show stored: pre(X)

hold for 3 sec. to use auto exposure mode

ReseT TO FacTORY seTTinGs

follow this procedure to change back to factory setting 1080p60. 1. turn the microscope off2. press and hold the center button down while turning the power on3. Keep holding the center button down for 25 seconds4. release the center button and turn the power off5. turn the power back on and the microscope is set to factory

setting 1080p60

turn off/on

laser on/off (warning! laser rediation when turned on)

Zoom in

Zoom out

push both plus and minus to change from auto focus to manual focus. You can now adjust the focus manually by using the plus/minus buttons

if you wish to focus on something close

if you wish to focus on something further away

7. OpeRaTiOn

XKeY control box for tagarno fhd functions. do only connect equipment distributed by tagarno.

control buttons for tagarno fhd functions. do only connect equipment distributed by tagarno.

cOnTROl OpTiOnXKeY cOnTROl bOX

OpeRaTiOn (1/2)OpeRaTiOn (1/2)

8

1. open the osD menuto open the tagarno on screen display menu, press and hold the center button for approximately 5 seconds.

2. Choose lens set the current close-up lens by using the left/right arrows on the control boX XKeY. on a tagarno full hd system, the choice naturally is between lens +3, +4, +5 or +10. lens +4 is factory default. continue using the down arrow.

3. Choose monitor widthpress the center button to set up the width of the monitor. You need to measure the horizontal width of the monitor panel on your monitor, select one digit at a time by using the left/right arrows and adjust the digits with the up/down arrows. switch between millimeters and inches via the up/down buttons. monitor 22” fhd is factory default. to store change in settings press the center button.

4. Set start magnificationSelect which magnification level you need your FHD system to use as start up level. press the center button and select one digit at a time in the bottom of the page, by using the left/right arrows and adjust the digits with the up/down arrows. by pressing the center button one more time, you have selected the values chosen. press the down arrow to choose format.

when turning on your full hd system, you are informed of the given units, serial number (sn), version and resolution.

On scReen DisplaY (OsD)

OpeRaTiOn (2/2)

5. Choose format You have the option to switch between different video formats, 1080p 60fps being the highest quality. select the required format by pressing the center button, and use arrow keys left/right to select between 6 different formats.

6. Select OSD presetsYou need to choose between respectively alwaYs on, off or timeout using the left/right arrows in order to have the osd menu displayed continuously, never or for 3 seconds at the time. continue by pressing the down arrow.

7. Color boostthe osd menu gives you the possibility to choose between two color settings; color boost on or off, by using the left/right arrows. which setting chosen, is a matter of individual preferences and the object projected on screen. continue by pressing the down arrow.

8. Flip picturein the menu you have the possibility to rotate the screen image 180 degrees, or choose the standard view by using the left/right arrows. choose between the two views by pressing the left/right buttons. continue by pressing the down arrow. press the down button one time to mark the save and exit option.

9. save presetsto save your presets and exit the menu, press the center button and thereby return to the image displayed on the monitor, using your recently saved presets.

if you have changed the various formats, your full hd system needs to be restarted. this will be indicated in the bottom if needed.

9

8. TecHnical speciFicaTiOns

Dimensions h: 121mm/4.76” d: 100mm/3.94”

Weight 1.5 kg/3.3 lbs

Camera resolutionfhd 1080p, 1920x1080p at 59,94/50/29,97/25hzhd 720p, 1280x720p at 59,94/50hz

Camera zoom 30x optical

Autofocus Yes

Power consumption 7,4 w

Standby consumption 0.5w

storage -5 - +60ºc / +23 - +140ºf, 20 - 90% rh

operation +5 - +40ºc / +41 - +104ºf, 20 - 80% rh

Work height min: 95mm/3.74” max: 360mm/14.17”

Work depth adjustable

Auto Monitor Detect no

Plug connection HDMI, USB 3.0 & ESD (fixed cables)

TecHnical speciFicaTiOns (1/2)

d

d

h

10

TecHnical speciFicaTiOns (2/2)

FeaTuRes

auto & manual focus choose monitor width flip picture

iris, gain and preset mode Set start magnification image capture, pc (with third-party software)

osd menu choose format

choose lens select osd presets

laser pointer (on/off) color boost

lens

Dimensions 58 mm/2.3”

Included lens +4

lens Lens to object distance Magnification on 22" monitor

+3 333mm/13.22” 1.2x - 36.0x

+4 250mm/9.84” 1.6x - 48.0x

+5 200mm/7.87” 2.0x - 60.0x

RecOmmenDeD mOniTOR FORmaT

Panel format 16:9 (widescreen)

How to link hdmi input

Response time 2 ms

signal format fhd 1920x1080

accessORies

XKeY control box light Kit

hd 22” and 24” widescreen monitor angle brackets

flexarm cleaning kit

foot switch

11

FULL HD 1080p @ 59,94/50Hz

OS Desktop Laptop

Windows 7, 8 or 10 (with DirectX 11)

Memory 8GB

CPU Intel® Core™ i5 or i7 @2.4GHz, (3rd or 4th generation named 3xxx or 4xxx)

CPU: Intel® Core™ i5 or i7 @2.4GHz (4th generation named 4xxx)

Hard Disc Space 1GB required (SSD type recommended)

Connections USB 3.0 xHCI host controller (Intel chipset recommended)

Integrated Graphics Intel® HD Graphics 4000 Intel® HD Graphics 4400

Dedicated graphics card AMD Radeon™, HD 7xxx Series with 2GB RAM

nVidia GeForce GT 740M with 2GB RAM

Monitor resolution 1920x1080 (recommended)

FULL HD 1080p @ 29,97/25Hz anD HD 720p @ 59,94/50/30/25Hz

OS Desktop Laptop

Windows 7, 8 or 10 (with DirectX 11)

Memory 4GB

CPU Intel® Core™ Dual@3.0GHz or i3@2.4GHz, (3rd generation named 3xxx)

Intel® Core™ i3 @ 3.2GHz, (3rd generation named 3xxx)

Hard Disc Space 1GB required (SSD type recommended)

Connections USB 3.0 xHCI host controller (Intel chipset recommended)

Integrated Graphics Intel® HD Graphics

Dedicated graphics card AMD Radeon™, 1GB ram nVidia GeForce GT 1GB RAM

Monitor resolution 1920x1080 (recommended)

SoFtware recommenDeDWindows 7 Youcam 6 + Youcam 7 (Youcam 7 is only compatible with video format FULL HD 1080P @ 25/30Hz)Windows 8 Windows 8 Camera App Windows 10 Windows 10 Camera App

9. sYsTem RequiRemenTs

12

• Storeandusethemicroscopeinadry,cleanandventilatedroom.• Donotplacetheproductindirectsunlight,nexttoaradiator/heaterorsomeplacewhere

thesystemmaybesubjectedtoliquids.• Allplugsaredesignedtobeusedinonewayonly.Therefore,youshouldneveruseforce

whenyouconnectthesystem.• Remembertodisconnectallelementsifyouintendtomovethemicroscope.• Ifyoumovetheproductfromacoldtoahotroom,youmustwaitatleastanhourbeforeyou

turniton,toavoidshortcircuitsduetocondensation.• Removethecablesbypullingtheplugitself-neverbypullingthecable.• IftheTAGARNOneedsrepair,neverdoityourself,contactyourdistributor.• Whencleaningtheproduct,pleaseturnoffthesystemandwaituntillthesystemhas

cooledoff.• Cleantheproductwithadampcloth.Neverusestrongcleaningagentsorchemicals

-thesemaydamagethemicroscope.• CleanthelensregularlywithisopropylalcoholandamicrofiberclothorwithourTAGARNO

cleaningkit.

Maintenance

WarrantyWarranty terms for the product shall be as follows:

TAGARNOwarrantsthattheproductwillcorrespondwiththespecificationatthetimeofdeliveryandwillbefreefromdefectsinmaterialandworkmanshipforaperiodof24months(2years)fromdateofinvoicefromSupplier.

This warranty shall cover:

a.Thereplacementofdefectiveparts.b.Alllabourcoststoexchangedefectivepartsinproduct.c.Completefunctionstestofproductbeforereturntoenduser’ssite.d.ReturntransportcostsofproductfromTAGARNOtoenduser’ssite.

Thewarrantyonlyappliesiftheproductispacked,shipped,stored,handledandmaintainedcorrectly.Failuresduetoimproperpackingandtransportarenotcovered.Failuresduetodropsandsuddenblowsarenotcovered.Failuresduetostorageandhandlinginextremehighorlowtemperaturesarenotcovered.Failuresduetostorageorhandlinginextremehighhumidityarenotcovered.

ergonoMical recoMMendationsPleasebecarefulwhencarryingtheproductfromoneplacetoanother.Pleasedonotliftthemicroscopebygrabbingthecameraarm.

AllTAGARNOproductsaremarkedwithaproductlabel:

Values marked with X varies from product to product and are replaced by specific numbers and letters.

10. mainTenance

11. waRRanTY

12. eRGOnOmical RecOmmenDaTiOns

13

PRODUCTMODEL ART Inspection camera unit

MANUFACTURERNAME TAGARNO A/SADRESS Sandøvej 4ZIPCODE/CITY 8700 HorsensCOUNTRY DenmarkPHONE +45 76251111

DESCRIPTION TAGARNO A/S hereby declares that the product listed above, consisting of a camera unit and a 12V power supply, is in compliance with the following European directive:

EMC DIRECTIVE 2014/30/EU

By conforming to the following harmonised standards:

EN 61010-1:2010EN 61326-1:2013

The declaration is issued by: MANUFACTURER TAGARNO A/S

TAGARNO A/SSandøvej 4

8700 HorsensDenmark

+45 76251111 mail@tagarno.com

www.tagarno.com

tagarno fhd Zap | type no.: 690600

13. DeclaRaTiOn OF cOnFORmiTY