Manual MB ION 330 Mainboard

IPX7A-IONMotherboard Reference Guide

2 IPX7A-ION Motherboard Reference Guide

ContentsContents ....................................................................................2

Notices.......................................................................................3

Safety information ....................................................................4

Specifications summary ..........................................................5

Hardware Installation1 Before you proceed ............................................................................... 8

Package contents .........................................................................82 Motherboard layout ............................................................................... 9

Top view .......................................................................................9Rear panel connectors .................................................................9

4 System memory ................................................................................... 10Memory type ...............................................................................10Qualified Vendors List (QVL) ......................................................10Installing a SO-DIMM ................................................................. 11Removing a SO-DIMM ............................................................... 11

5 Expansion slot ..................................................................................... 12Installing an expansion card .......................................................12

6 Selectors ............................................................................................... 137 Connectors ........................................................................................... 148 BIOS Setup reference .......................................................................... 20

Main ............................................................................................20Advanced ...................................................................................21Power .........................................................................................24Boot ............................................................................................28Exit .............................................................................................30

IPX7A-ION Motherboard Reference Guide 3

NoticesFederal Communications Commission StatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and• This device must accept any interference received including interference that

may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter-ference by one or more of the following measures:

• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

NOTE: The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Canadian Department of Communications StatementThis digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Cana-dian Department of Communications.

This class B digital apparatus complies with Canadian ICES-003.


Safety informationElectrical safety• To prevent electrical shock hazard, disconnect the power cable from the electri-

cal outlet before relocating the system.• When adding or removing devices to or from the system, ensure that the power

cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These devices could interrupt the grounding circuit.

• Make sure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.

Operation safety• Before installing the motherboard and adding devices on it, carefully read all

the manuals that came with the package.• Before using the product, make sure all cables are correctly connected and the

power cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from con-nectors, slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.

• Place the product on a stable surface.• If you encounter technical problems with the product, contact a qualified ser-

vice technician or your retailer.

IMPORTANT: This symbol of the crossed out wheeled bin indicates that the product (electrical and electronic equipment) should not be placed in mu-nicipal waste. Check local regulations for disposal of electronic products.


CPU Supports : ATOM Serial CPU FSB : 533 MHz

Chipset MCP7A-ION

Memory Dual channel, Non-ECC, Unbuffered DDR2 Supported, Two 200 pin DDR2 SO-DIMM slots, Max. to 8GB Types: PC2-5400 (DDR2-667), PC2-6400 (DDR2-800)

Expansion slots

1x PCI Express Graphic slot (x16)

Audio Realtek ALC662 (6-channel)

LAN Gigabit Realtek RTL8211CL

Graphic Integrated Graphic in Chipset

Storage MCP7A-ION built-in: 4x SATA connectors, SATA300/150

USB 8x USB 2.0 ports

Rear panel I/O ports

1x Keyboard (PS/2) port 1x Mouse (PS/2) Mouse port 1x Display (D-SUB) port 1x Display (DVI-I) port 1x Display (HDMI) port 1x SPDIF output port 2x USB 2.0 ports 1x LAN (RJ-45) port + 2x USB 2.0 ports 3x Audio jacks (6-channel)

Internal connectors

1x ATX power connector 2x System fan connectors 4x SATA connectors 1x Front panel audio connector 1x COM port connector 1x CD in connector 1x ROM recovery connector 1x Front panel connector 2x USB connectors

BIOS SPI 8Mb (AMI)

Form factor mini-ITX (170 mm x 170 mm)

Specifications summary


Hardware InstallationThis manual provides descriptions of each component on the motherboard and how to setup necessary items.


1 Before you proceedTake note of the following precautions before you install motherboard components or change any motherboard settings.

• Unplug the power cord from the wall socket before touching any compo-nent.

• Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.

• Hold components by the edges to avoid touching the ICs on them.• Whenever you uninstall any component, place it on a grounded antistatic

pad or in the bag that came with the component.• Before you install or remove any component, ensure that the ATX power

supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.

• Before you install the motherboard, study the configuration of your chas-sis to ensure that the motherboard fits into it.

• Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components.

Package contentsCheck your package for the following items.

Motherboard • Cables • Accessories • Drivers & Utilities Support Disc • This Motherboad Reference Guide•


2 Motherboard layout

ATXPOWER

F_P

AN

EL

F_U

SB

1F_

US

B2

SYS_FAN1SYS_FAN2

LAN + USB

USB

BATTERY

SPDIF_out

AUDIO

DVI VGA

KB + MS

SATA

2 3SATA

0 1

HDMI

F_AUDIO PCIE X16

ROMRECOVERY

CDIN1

CMOS + PW

XM

M1

XM

M3

COM1

USB 2.0connectors

ROM recoveryconnector

COM portconnector

ATX powerconnector

Memorysockets

System fan connectors

Front panelconnector

SATAconnectors

SATAconnectors

USBconnectors

LAN & USBconnectors

Audioports

PCIE16connector

Front panel audio connector

CD inconnector

SPDIF audiooutput

Display(DVI & D-SUB)ports

Keyboard & mouse(PS/2) ports

Northbridge/

ATOM CPU

Southbridge

Display (HDMI)port

Clear CMOS &Password

Rear panel connectors

Top view

Mouse (PS/2) port

Display (D-SUB) port

Keyboard (PS/2) port

LAN (RJ-45) port

Display (DVI-I) port

Display (HDMI) port

Blue: Line In

Lime: Front-L/R out

Pink: Mic In

SPDIF output port

USB 2.0 ports


4 System memoryMemory typeThe motherboard comes with two Double Data Rate 2 (DDR2) Small Outline Dual In-line Memory Modules (SO-DIMM) sockets.

The figure illustrates the location of the DDR2 SO-DIMM sockets:

XMM1 XMM3

Size Vendor Model CL Brand SS/DS Component

DIMM socket support (Optional)

A* B*DDR2 667/512MB NANYA NT512T64UH8B0FN-3C N/A NANYA DS NT5TU32M16BG-3C Pass Pass

DDR2 667 1GB MICRON MT16HTF12864HY-667D3 5 MICRON DS 7WD22 D9GMH Pass Pass

DDR2 667 1GB HYNIX HYMP512S64CP8-Y5 AB N/A HYNIX DS HYP5PS12821C FP-Y5 702A Pass Pass

DDR2 667 1GB KINGSTON KY9530-HYC N/A HYNIX DS HY5PS12821C FP-Y5 730AA Pass Pass

DDR2 667 1GB SAMSUNG M470T2864DZ3-CE6 N/A SAMSUNG DS K4T1G164QD-ZCE6 Pass Pass

DDR2 667 2GB KINGSTON KVR667D2S5 N/A KINGSTON DS AD9330.02 0841 PTGC D1288TPFCGL3U Pass Pass

DDR2 800 1GB QIMONDA HYS64T128020EDL-2.5 C2 N/A QIMONDA DS HYB18T1G160C2F-2.5 FSS25181 Pass Pass

DDR2 800 1GB MICRON MT8HTF12864HDY-800E1 6 MICRON DS 7QE22D9MPF Pass Pass

DDR2 800/1GB HYNIX HYMP112S64CP6-S6 AB N/A HYNIX DS HY5PS1G1G31C Pass Pass

DDR2 800 1GB SAMSUNG M470T2864EH3-CF7 N/A SAMSUNG DS K4T1G164QE-HCF7 Pass Pass

DDR2 800 1GB NANYA NT1GT64UH8C0FN-AD N/A NANYA DS NT5TU64M16CG-AD 73606800CP Pass Pass

DDR2 800 2GB HYNIX HMP125S6EFR8C-S6 AB N/A HYNIX DS H5PS1G83EFR S6C R26A Pass Pass

DDR2 800/2GB SANMAX SMD-N1G88HP-8E N/A HYNIX DS HY5PS1G832C Pass Pass

DDR2 800 2GB QIMONDA HYS64T256020EDL-2.5 C2 N/A QIMONDA DS HYB18T1G8020C2F-2.5 FSS12 Pass Pass

DDR2 800 2GB SAMSUNG M470T5663EH3-CF7 N/A SAMSUNG DS 852 HCF7 K4T16084QE Pass Pass

DDR2 800 2GB MICRON MT16HTF25664HY-800G1 6 MICRON DS 8WG22 D9JWB Pass Pass

DDR2 800 2GB KINGSTON HP5189-2822-HYC N/A HYNIX DS HY5PS1G831C FP-S6 C 837E Pass Pass

DDR2 800/2GB ADATA A70-8C0039 N/A ADATA DS AD20908A8D-25EGE0839 Pass Pass

Remark:A* : Supports one module inserted in any slot as Single-channel memory con-

figuration.

B* : Supports one pair of modules inserted into either the blue slots or the black slots as one pair of Dual-channel memory configuration.

Qualified Vendors List (QVL)


TIP: Support the SO-DIMM lightly with your fingers when pressing the re-taining clips. The SO-DIMM might get damaged when it flips out with extra force.

Installing a SO-DIMMWARNING: Unplug the power supply before adding or removing SO-DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components.

To install a SO-DIMM:1. Firmly insert a SO-DIMM into the

socket at a 30˚ angle with the notch on the SO-DIMM matching the break on the socket.

2. Push down on the SO-DIMM until the retaining clips click into place.

1. Simultaneously press the retaining clips outward to unlock the SO-DIMM. The SO-DIMM will automati-cally pop up.

2. Remove the SO-DIMM from the socket.

NOTE: A SO-DIMM is keyed with a notch so that it fits in only one direction. Do not force a SO-DIMM into a socket to avoid damaging the SO-DIMM.

4 System memory

Removing a SO-DIMM

Follow these steps to remove a SO-DIMM:

(This is only an example.)

(This is only an example.)


5 Expansion slotIn the future, you may need to install expansion cards. The following shows the slot and the expansion card that it supports.

Installing an expansion cardIMPORTANT: Make sure to unplug the power cord before adding or remov-ing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.

To install an expansion card:1. Before installing the expansion card, read the documentation that came with it

and make the necessary hardware settings for the card.2. Remove the system unit cover (if your motherboard is installed in a chassis).3. Remove the bracket opposite the slot that you intend to use. 4. Align the card connector with the slot and press firmly until the card is com-

pletely seated on the slot.5. Secure the card to the chassis with the screw you removed earlier.6. Replace the system cover.

PCI Express card (x16)


6 SelectorsClear CMOS and passwordThis selector allows you to clear the Real Time Clock (RTC) RAM and password in CMOS. You can clear the CMOS memory of date, time, system setup param-eters, and passwords by erasing the CMOS RTC RAM data.

To clear the password and setting:1. Turn OFF the computer.2. Move the cap to Clear.3. Turn ON the computer to POST screen.4. Turn OFF the computer.5. Move the cap back to Default.6. Enter BIOS setup to verify or configure new settings.

IMPORTANT: Except when using this function, do not remove the jumper cap from the default position or else there may be a system boot failure!

(Default)123

123

Clear CMOS and password

CMOS+PW


ATX power connectorThis connector is for the ATX power supply plug. The power supply plug is de-signed to fit this connector in only one orientation. Find the proper orientation and push down firmly until the connector completely fits.

NOTE: Use of a power supply unit (PSU) with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. NOTE: Make sure that your PSU can provide at least the minimum power required by your system. NOTE: If you intend to use an older PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin power plug can provide at least 15A on +12V and that the PSU has a minimum power rating of 350 W. The system may become unstable or may not boot up if the power is inadequate.NOTE: You must install a PSU with a higher power rating if you intend to install additional devices.

7 Connectors

+3 V

olts

Pow

er O

KG

roun

d

Gro

und

Gro

und

Gro

und

Gro

und

Gro

und

Gro

und

Gro

und

PS

ON

#

+5 V

olts

+5 V

olts

+5 V

olts

5 V

olts

12

Volts

+3 V

olts

+12

Volts

+12

Volts

+5V

Sta

ndby

+5 V

olts

+5 V

olts

+3 V

olts

+3 V

oltsATXPOWER


System fan connectorsConnect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.

7 Connectors

SY

S_F

AN

_TA

CH

+12V

GN

D

SY

S_

FAN

_ P

WM

SYS_ FAN2 SYS_ FAN1

Gro

und

+12V

Rot

atio

n

Serial ATA connectorsThese connectors are for the Serial ATA signal cables for Serial ATA devices.

SATA0 SATA1

Ground

Ground

GroundSATA_RX(+)SATA_RX(-)

SATA_TX(-)SATA_TX(+)

SATA2 SATA3


7 ConnectorsFront panel audio connectorThis connector is for a chassis-mounted front panel audio I/O module that supports HD Audio.

NOTE: It is recommended that you connect a high-definition front panel audio module to this connector to utilize this motherboard’s high-definition audio capability.

USB connectors (dual ports)These connectors are for USB 2.0 ports. Connect a USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specifications which support up to 480 Mbps connection speed.

WARNING: Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!

USB*(-)USB*(+) USB*(+)

USB*(-)

Ground Ground

SBV SBV

NC

F_USB1

F_USB2

MIC

*_L

MIC

*_R

LIN

E*_

RG

roun

d

Gro

und

LIN

E*_

LJD

_LIN

E*

JD_M

IC*

FP_P

RE

S#

F_AUDIO


7 ConnectorsInternal serial port connectorThis connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to the system chassis.

COM1

DD

C*#

TTX

D*

Gro

und

RR

TS*#

RR

XD

*D

DTR

*#

DD

SR

*#C

CTS

*#R

RT*

#

ROM RECOVERY

Ground3VSB

SPI_CS#SPI_CS#SPI_MOSISPI_MISOSPI_CLK

ROM recovery connectorThis connector allows qualified technicians to reload firmware into the SPI boot flash in case there is problem with the data.


7 ConnectorsCD Audio input connectorThis connector allows you to receive stereo audio input from sound sources such as an optical disc drive, a TV tuner, or a specialized audio/sound-processing card.

CD IN

Left Audio ChannelGround

Right Audio ChannelGround


7 ConnectorsSystem panel connectorThis connector supports several chassis-mounted functions.

System power LED (2-pin PLED)This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power.

Hard disk drive activity LED (2-pin +HDLED)This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD.

ATX power button/soft-off button (2-pin PWRBTN)This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.

Reset button (2-pin RESET)This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.

Ground

HDLED(+)HDLED(-)

+HDL

EDRE

SET

PWRGround Reset

PW

RB

TNP

LED PLED(-)

PLED(+)

FPA_DET#

F_PANEL


8 BIOS Setup referenceBIOS setup programWhen the computer first starts up (before entering Windows), press and hold the <Del> key to enter the BIOS setup program. (Press <Ctrl+Alt+Delete> to restart if you missed the opportunity.)

NOTE: Default BIOS settings apply for most conditions to ensure optimum performance. If this system becomes unstable after changing any BIOS set-tings, load the default settings to ensure system compatibility and stability. Find the load default options under the Exit Menu.

AMIBIOSDisplays the auto-detected BIOS information.

System MemoryDisplays the auto-detected system memory information.

System Time [xx:xx:xx]This item allows you to set the system time.

System Date [Day xx/xx/xxxx]This item allows you to set the system date.

Main

The BIOS setup screens shown in this section are for reference purposes only, and may not exactly match what you see on your screen.

BIOS SETUP UTILITY

Main

FieldField

AMIBIOS

Use [ENTER], [TAB]

or [SHIFT-TAB] to

select a field.

Use [+] or [-] to

configure system Time.

Select ScreenSelect ItemChangeSelectGeneral HelpF1Save and ExitF10ExitESC

Tab

Version :0800

:05/14/09

:2048MB

Build Date

Size

System Overview

System Memory

System TimeSystem Date

[19:43:50][Fri 05/22/2009]

BootSecurity ExitPowerAdvanced

v02.61 (C) Copyright 1985-2009, American Megatrends, Inc.


8 BIOS Setup referenceAdvanced

BIOS SETUP UTILITY

Advanced

F1

Configure CPU.

Select ScreenSelect ItemGo to Sub ScreenGeneral HelpSave and ExitF10ExitESC

Enter

Advanced Settings

Main

CPU ConfigurationSATA ConfigurationUSB ConfigurationHardware Health ConfigurationOnboard Device Settings


BootSecurity ExitPower

CPU ConfigurationThis item provides the auto-detected CPU specifications.

SATA ConfigurationThe items in this menu allow you to set or change the configurations for the SATA devices installed in the system. Select an item then press <Enter> if you wish to configure the item.

SATA ControllerDefault: [Enabled] / Options: [Disabled] [Enabled]

SATA Controller ModeDefault: [SATA Mode] / Options: [SATA Mode]

1st, 2nd, 3rd, 4th DriveWhile entering Setup, the BIOS automatically detects the presence of SATA devices. There is a separate sub-menu for each SATA device. Select a device item then press <Enter> to display the SATA device information.


8 BIOS Setup referenceAdvanced

USB ConfigurationUSB FunctionsThis item allows you to enable or disable the USB Functions.

Default: [Enabled] / Options: [Disabled] [Enabled]

USB 2.0 ControllerThis item allows you to change the USB 2.0 Controller setting.


Hardware Health ConfigurationCPU TemperatureThe onboard hardware monitor automatically detects and displays the CPU tem-perature.

Display field only: [xxxºC/xxxºF]

System TemperatureThe onboard hardware monitor automatically detects and displays the System temperature.

Display field only: [xxxºC/xxxºF]

System Fan1/Fan2 SpeedThis item shows how fast your system fan is running. The fields for unconnected connectors will read “N/A”.

Display field only: [xxxx RPM]

System Fan1/Fan2 CheckThis item alllows your system to detect if the fan is faulty.

Default: [Disabled] / Options: [Disabled] [Enabled]


8 BIOS Setup referenceAdvancedFan ControlThis item allows you to enable or disable the Fan Control feature that automatically adjusts the fan speeds for more efficient system operation.


Initial/Idle Fan Voltage Display field only [x.xxx V]Acceleration Starts at Display field only [xxxºC/xxxºF]PWM Ramp Range Display field only [xxx ºC]Switches to Full Speed at Display field only [xxxºC/xxxºF]Fan Control ModeThis item allows you to choose how your fan is controlled.

Default: [Auto] / Options: [Auto]

Onboard Device ConfigurationOnboard VGA ConfigurationThis item allows you to configure your VGA settings.

Primary Graphics AdapterDefault: [PCIE VGA Card First] / Options: [Internal VGA First] [PCIE VGA Card First]

iGPU Frame Buffer SizeDefault: [256MB] / Options: [256MB]

High Definition AudioThis item allows you to enable or disable High Definition Audio.


Onboard LAN SettingsThis item allows you to enable or disable the Onboard LAN settings.


PXE rom boot supportThis item allows you to enable or disable PXE rom boot support.



8 BIOS Setup referencePower

The Power menu items allow you to change the settings for the ACPI Con-figuration. Select an item then press <Enter> to display the configuration options.

ACPI Configuration

Suspend ModeThis item allows you to select the Advanced Configuration and Power Interface (ACPI) state to be used for system suspend.

Default: [Auto] / Options: [S1 (POS)] [S3 (STR)] [Auto]

APM ConfigurationPower On By PME#This item allows you to enable or disable Power On By PME#.


Resume On By RTC AlarmThis item allows you to enable or disable Resume On RTC Alarm.


BIOS SETUP UTILITY

Main BootPower Exit

Select the ACPI

state used for

System Suspend.

F1

Select ScreenSelect ItemChange OptionGeneral HelpSave and ExitF10ExitESC

+-

ACPI Configuration

APM Configuration

Suspend mode [Auto]

Power on By PME#Power on By RTC Alarm

Power on By RingEUP Mode

Restore on AC Power Loss

[Disabled][Disabled]

[Disabled][Enabled]

[Power Off]

SecurityAdvanced



8 BIOS Setup referencePower

Restore On AC Power LossWhen set to [Power Off], the system goes into off state after an AC power loss. When set to [Power On], the system goes on after an AC power loss. When set to [Last State], the system goes into either off or on state, whatever the system state was before the AC power loss.

Default: [Power off] / Options: [Power Off] [Power On] [Last State]

Power On By RingThis item allows you to enable or disable Power On By Ring.


EUP ModeThis item allows you to enable or disable the EUP mode.



8 BIOS Setup referenceSecurity

BIOS SETUP UTILITY

Advanced

F1

Install or Change the

password.

Select ScreenSelect ItemChangeGeneral HelpSave and ExitF10ExitESC

Enter

Security Settings

Main

Supervisor Password

Change Supervisor Password

:Not Installed:Not InstalledUser Password


Boot ExitPower Security

Enter New Password

Change Supervisor PasswordSelect this item to set or change the supervisor password. The Supervisor Pass-word item on the top of the screen shows the default Not Installed. After you set a password, this item shows Installed.

To Set A Supervisor Password:1. Select the Change Supervisor

Password item and press <Enter>.2. From the password box, type a

password composed of at least six letters and/or numbers, then press <Enter>.

3. Confirm the password when prompted.

The message “Password Installed” appears after you successfully set your pass-word. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message “Password Uninstalled” appears.

NOTE: If you forget your BIOS password, you can clear it by erasing the CMOS Real Time Clock (RTC) RAM. See your hardware documentation for information on how to erase the RTC RAM.


8 BIOS Setup referenceSecurityChange User PasswordSelect this item to set or change the user password. The User Password item on the top of the screen shows the default Not Installed. After you set a password, this item shows Installed.

To Set A User Password1. Select the Change User Password item and press <Enter>.2. On the password box that appears, type a password composed of at least six

letters and/or numbers, then press <Enter>. 3. Confirm the password when prompted.

The message “Password Installed” appears after you set your password success-fully. To change the user password, follow the same steps as in setting a user password.

Clear User PasswordSelect this item to clear the user password.

Password CheckWhen set to [Setup], BIOS checks for user password when accessing the Setup utility. When set to [Always], BIOS checks for user password both when accessing Setup and booting the system.

Default: [Setup] / Options: [Setup] [Always]

Boot Sector Virus ProtectionThis item allows you to enable or disable the Boot Sector Virus Protection.



8 BIOS Setup referenceBoot

Boot Settings Configuration Quick BootThis item allows you to enable or disable the system quick boot feature. When Enabled, the system skips certain tests while booting.


Quiet BootThis item allows you to enable or disable the full screen logo display feature. When disabled, normal POST messges are displayed.


Bootup Num-LockThis item allows you to select the power-on state for the NumLock.

Default: [On] / Options: [Off] [On]

PS2/Mouse SupportThis item allows you to select the PS2/Mouse setting.

Default: [Auto] / Options: [Auto]

BIOS SETUP UTILITY

Boot Settings Configuration

Main Boot Exit

Configure Settings

during System Boot.

F1


Enter

Boot Setting Configuration

SecurityPowerAdvanced



8 BIOS Setup referenceBoot

Keyboard Error Message DisplayThis item allows you to enable or disable the “Keyboard Error” message during bootup.


Hit ‘DEL’ Message DisplayThis item allows you to enable or disable the “Press DEL to run Setup” message during bootup.



The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.

Save Changes and ExitOnce you are finished making your selections, choose this option from the Exit menu to ensure the values you selected are saved to the CMOS RAM. An onboard backup battery sustains the CMOS RAM so it stays on even when the PC is turned off. When you select this option, a confirmation window appears. Select Ok to save changes and exit.

NOTE: If you attempt to exit the Setup program without saving your changes, the program prompts you with a message asking if you want to save your changes before exiting. Press <Enter> to save the changes while exiting.

Discard Changes and ExitSelect this option only if you do not want to save the changes that you made to the Setup program. If you made changes to fields other than System Date, System Time, and Password, the BIOS asks for a confirmation before exiting.

Exit

8 BIOS Setup reference

BIOS SETUP UTILITY

Main Boot Exit

Exit system setupafter saving thechanges.

F1


Enter

Exit Options

Save Changes and ExitDiscard Changes and ExitDiscard Changes

Load Optimal DefaultsLoad Failsafe Defaults

F10 key can be usedfor this operation.

SecurityPowerAdvanced



Discard ChangesThis option allows you to discard the selections you made and restore the previ-ously saved values. After selecting this option, a confirmation appears. Select Ok to discard any changes and load the previously saved values.

Load Optimal DefaultsThis option restores BIOS fields to their factory defaults to run the system at “op-timal performance”. When you select this option, a confirmation window appears. Select Y to load defaults. Make sure you save changes before exiting.

Load Failsafe Defaults If you made changes to this BIOS setup utility and your system becomes unstable as a result, select this option to restore BIOS fields to their “low performance” settings to troubleshoot BIOS setting problems. When you select this option, a con-firmation window appears. Select Y to load defaults. Make sure you save changes before exiting.

Exit

8 BIOS Setup reference

Manual MB ION 330 Mainboard

Documents

Transcript of Manual MB ION 330 Mainboard