manual - La Marzocco USA · 3 eN 1. Introduction 2. Components Verify that all parts are included...
Transcript of manual - La Marzocco USA · 3 eN 1. Introduction 2. Components Verify that all parts are included...
manualswift epsbThe Swift grinder is the only grinder that grinds and tamps on demand, with no waste and no mess, to an accurate volumetric dose. Swift’s clever engineering and design guarantee level and consistent coffee beds, time after time. Flat ceramic burrs ensure minimal heat buildup during the grinding process. Compatible with all La Marzocco espresso machines. Swift is ideal for high volume locations where consistency is key. Swift technology maintains quality in the cup, shot after shot, no matter who is using it.
ENswift epsb
certifications available:
Operating Manual V2.1 - 11/2014
La Marzocco S.r.l.
Via La Torre 14/HLocalità La Torre50038 Scarperia e San Piero (Firenze) - ITALIA
T: +39 055 849 191F: +39 055 849 1990
EN
Chapters1. Introduction2. Components 3. Specifications4. Installation5. EngagingthePortafilter6. OperatingtheSwift epSb
6.1 Swift epSb6.2 Swift S/D
7. AdjustingCoffeeGrind8. AdjustingDoseQuantity
8.1 Swift epSb 8.2 Swift S/D
9. DailyCleaning10. impeller11. burr Change-Out 12. Chute Clean-Out tool 13. fuse Replacement and Reset Switches 14. TipsandTroubleshooting15. electrical Diagrams 16. Cleaning procedure 17. Recycling
page 3page 3page 4page 5page 6page 7page 7page 7page 9page 10page 10page 11page 15page 18page 20page 24page 25page 27page 29page 31page 32
EN3
1. Introduction
2. Components
Verify that all parts are included when you receive your new Swift EPSB.
a. Grinderb. two bean hoppers and lidsc. Driptrayd. fuse pulling toole. Screwdriverf. Cleaning brushg.22mm.Portafilterbasketsh. tamper cover lidi. fuses (inside tamper cover lid)j. Long-armL-key3/32hexsizek.Grinderdischargeclean-outtoolManualWarrantyandregistrationcard
Espresso Preparation SystemCongratulations on choosingthe Swift epSb from La Marzocco. Your applicationof this new product in yourcafé or home will result in a numberofimportantbenefitstoyou.
Quality, Consistency, Conservation, and Speed.YournewSWIFTEPSb grinds, doses and tamps coffeedirectly into the portafilter,eliminating the need to dothis manually. It measuresand doses by volume, not
time, so waste and productinconsistencyarereduced.Atthesametime,theSWIFTEPSb enhancescoffeefreshnessbygrinding coffee by dose, notbybulk.Thismanualincludesinformation about how tomaintain and troubleshoot
your SWIFTEPSb foroptimalperformance.Please review it carefully.
a.
b.
b.
c.
d.
e.
g.
f.
h.
j.
d, e, i, j, k . Inside tamper cover
k.
EN 4
3. Specifications
Height 65.5 cm/25.8 in.width 35 cm/13.8 in.Depth 36 cm/14 in.ShippingWeight 31kg/68lbs.Voltage Single phase 220 VAC or Single phase 110 VACAmperage 7.5 amps, 220 VAC or 15 amps, 110 VACBeanHopperCapacity 1.8kg/4lbs.eachWatts 780W
360 mm14 in
655 mm25,8 in
285 mm11,2 in
350 mm13,8 in
EN5
the Swift epSb is easy toinstall. However, there are several important considerationsto keep in mind. The SWIFT
epSb requires a grounded 110v, 15 amp (or 220v, 7.5 amp) power supply. It alsorequires a minimum 16” x16” (406 mm x 406 mm)
space on the counter. Since the unit is 26” (660 mm) in height,allow at least 30” (762 mm) of vertical clearance sothere is sufficient space to
allowtheeasyremovalofthebean hoppers and lids. the Swift epSb weighs about 75 lbs(34kg),somakesureyourcounter will support this.
(1) install the bean hoppers and tighten the safetyscrews.
(2) plug the Swift epSb into a grounded 110v or 220v single phase power supply.
4. Installation
(4) Open the bean gates.
(3)Pourcoffeeintothebeanhoppers.
Leave space above the Swift EPSB.
EN 6
The portafilter engagesdirectly to the SWIFT EPSb. Since the Swift epSb has no watertight seal, it is
not necessary to force theportafilter intoplace.Engagethe portafilter with only alight amount of force. if the
grinder shiftson the countertop, you are using toomuchforce.
5. Engaging the Portafilter
there is no need to force it intoposition.
Engageportafiltergently.
(5) Turn on the grinder byengaging the main power switch. the red light will come on.
EN7
6. Operating the SWIFT EPSB6.1 Swift EPSBOnce the portafilter isengaged, press one of the start buttons located at thefront of the Swift epSb. The right and left buttonscorrespond to the right and leftbean hoppers. Coffeewill
be ground, dosed, and tamped from one of these locations,depending on which buttonyou press.The red indicatorlights located above the start buttons are illuminatedwhen the Swift epSb is grinding and tamping. Once
the red light corresponding to the button selected is nolonger illuminated, you mayremove the portafilter fromthe Swift epSb and engage it into the espresso machine.the Swift epSb tamps the coffee as it is ground.When
the volumeof ground coffeein the portafilter reachesthe set level, the grinding motorturnsoff.Thetampingmotor continues to run for1-3 seconds, “polishing” the tampedcoffee.
6.2 Swift S/Dthe Swift is now available in a Single/Double dose version which permits dosing and tamping into specific filtersfor either single or double doses.
Selecttherightorleftbeanhopper.
Removepreparedportafilter.
SiNGLE L116/A/SDOUBLE L115/A/S
Externallythismodelappearslikethestandardversion,butthe internal impeller, which deposits and presses the coffee, issmaller indiameterso that it does not get stuckinsideasinglefilter.
EN 8
flashing indicator lightsthe red indicator lights will flashforanumberofreasons.Thesearesummarizedbelow:• You attempted to start
the process with a full portafilter.
• The safety timer has runout due to an emptybeanhopper, a closed bean gate, or a plugged bean hopper chute.
• There is no portafilterengaged in the Swift epSb.
standardfiltersthatare normally supplied withespresso coffee machines orwith standard Swift models(doubleonly).
The filters designed for thisspecific model of the SWIFThave a different placementofholesthanstandardfilters.This difference makes itpossible to obtain an elevated qualityintheconsistencyofbrewing in spite of a grinder-doser with automatictamping.
Todoseandpresscoffeewhenusing a double filter, thereis a cushioning cylindricalring next to the externalcircumference of the impeller (see image here below).
Using the S/D Swift The S/D Swift grinder isactivatedbypressing the“S”switch ONCe to prepare a singlefilter(L115/A/S),and twiCe in a row to prepare adoublefilter(L116/A/S).As previously explained, thefilters used for the SWIFTEPSB are different from the
Blinkingindicatorlightsrelayinformation.
Swift S/D- in version Swift S/D the red indicator lights will flashwhen working the grinderfor a double doses.
EN9
7. Adjusting Coffee GrindToachieveyourdesiredbrewtime and coffee consistency,a manual adjustment can be made to the grinder to modify the grind of thecoffee.(Thetampingpressureis not adjustable and remains constant). Rotate the adjustor knobsasdescribedbelow.(1) Locate the grinder adjustor
knobthatcorresponds totheleftorrightsideofthegrinder.
(2)Grindingthecoffeemorefinely will result in aslower pour. to achieve a slower pour, adjust the knobsasfollows:
Leftbeanhopper: turn the knob counter-clockwise.Right bean hopper: turn theknobclockwise.
(3)Grindingthecoffeemorecoarsely will result in afaster pour. to achieve a faster pour, adjust the knobsasfollows:
Left bean hopper: turn theknobclockwise.
Rightbeanhopper: Turn the knob counter-
clockwise.When makingthis adjustment, remember to turn the knob in a minimum ofhalf-turn increments.brew one or two shots to test the adjustment.
Note: There are manyvariables that can affectcoffee,includingtemperature,humidity, and freshness ofthe roast. All of these can causeslightvariationsinshottimes.
Adjustcoffeegrind
SLOweRpOUR
fASteRpOUR
SLOweRpOUR
Leftbean
hopper
Rightbean
hopper
fASteRpOUR
EN 10
8. Adjusting Dose Quantity8.1 Swift EPSBthe Swift epSb is set to dose approximately16to18gramsof coffee in 22mm basket
provided with the grinder. it is possible to change the dosage quantity by raisingor lowering the height of the impeller. Additionally, the
Swift epSb is able to dose different quantities usingother baskets, availablethroughyourretailer.
Loosen set screw
(2) Using the long-arm 3/32 hex-sizeL-key,loosentheset screw in the collar of the tamper shaftcoupling.
(1) Remove the tamper cover as described on page 19.
Liftoffcover
(3) Holding the tamper shaft coupling in place,rotate the impeller in the directiondesired.
Holdtampershaftcouplerand rotate
impeller
WARNINGHAZARDOUS VOLTAGE
DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
EN11
(4) to increase the dosage amount, turn the impeller clockwise, as viewedfrom below. to decrease the dosage amount, turn the impeller counter-
clockwise,asviewedfrombelow.
Note: One 360° turn is equal to approximately 1 gram ofcoffee.
8.2 Swift S/D
increase the dosage Decrease the dosage(5) ensure that the set screw
is against the flat sideof the tamper shaft.Retightenthesetscrewinthe collar of the tamper shaftcoupling.
(6) Reassemble.
Key to performance:The3figureshereshowhowthe Single/Double Swift operates. Coffee drops through thechannels linked to the burrsinside the dosing chamber where it is deposited and tamped in layers by theimpelleruntilobtaining,onelayer at a time, the requiredamount. Single filter:The coffee is deposited andpushed downward, therefore tamped in a uniform manner bytheimpeller.The setting of the time forgrinding will determine the amount of ground coffeereadyforextraction.
Retightensetscrew
EN 12
Double filter:
The coffee is deposited andthen tamped in a uniform fashion by the impeller and
the cushioning cylindricalring, whose springs push downwards with the same force as the impeller.The quantity in this case is
determinedbythevolumeofgroundcoffeethatpushestheshaft upwards,which, at theend of the process, will arrest the motors of the grinder
and tamper through a switch connected to an electronic board.
EN13
Setting up the Swift Grinder S/DRegulation of single anddouble doses: to establishthe doses on this specificgrinderitisnecessarytoreadthrough the procedures for the standard Swift under the section “Regulation of quantity for dosing” as well as follow these procedures.BOtH MOtORS AND HOPPERS CAN DELiVER SiNGLE AND DOUBLE DOSESItismandatorytoproceedasfollows:Double dose:1)Turn off the machine and
remove the front tower cover to access to the screwsthatfixtheshaftofthe impeller.
2)Set the quantity of thecoffeinthefilterasonthestandard Swift model.(see image A)
3) Adjust the grind (double):
adjust thegrind toextract60ml in 25 seconds.
4) Set the height of the cylindrical ring: thecylindrical ringnext totheimpeller should be at a height that allows to obtain a coffeepuck surface thatiscompletelyeven.
NOtE: The regulation of theheight of the cylindrical ring(moveable part or tamper) is carried out by rotatingthe part clockwise to lift thering and rotating it counterclockwisetolower.
The cylindrical ring is heldinplaceby twobrass screws(see image b) so that the vibrations caused by therotation of the impellers donotalteritsposition.
Remove the two screws and manually rotate the part,graspingitfromthebottom.the distance between the impeller and the cylindricalringcanvaryfromaminimumof 4 mm to 6 mm, a length that permits to obtain a perfectly even coffee puck(see picture below).
Raisering(counterclockwise)
Lowerring(clockwise)
EN 14
Single dose:Thequantityofcoffeeforthesingle dose is regulated bytime.By turning the screw at theleft blue trimmer positionedatthebackofthekeypaditispossible to vary the grindingtime. Turningthescrewsclockwise,thetimeincreases,increasingthe dose.
turning them counter clockwise, the timedecreases,decreasing the dose.this model of the grinder supplies a double dose that can be set between 15 and 17 gr and a single dose that can be set between 7,5 and 8,5 gr.
1)Beforesettingup, test thesingledose:
a) if extraction timing of 30ml of espresso is less than 25 seconds, increase gram dose by rotating trimmerclockwise.
b) if extraction timing of 30ml of espresso is more than 25 seconds, decrease gram dose by rotating trimmercounterclockwise.
EN15
Daily cleaning of theSwift epSb is important to the quality of yourcoffee beverages and tothe mechanical life of the equipment. when the
cleaning instructions arecarried out each day, therewill be little chance of oldcoffee residue spoiling theflavor of your espressodrinks,orinterferingwiththe
mechanicaloperationofyourmachine. there are three areas that must be cleaned:the bean hoppers, the burr chamber, and the impeller.
9. Daily Cleaning
Close the bean gate Disconnect
(1) to clean the bean hoppers, close the bean gate to stop the flow of coffee beansto the grinding burrs.
(2)Grind coffee into theportafilter to clearthe remaining coffee.
Thismayrequiretwodoses.
(3) Disconnect the Swift epSb from its power supply.
Bean hoppers and burr chamber
WARNINGHAZARDOUS VOLTAGE
DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
EN 16
Loosensafetyscrew
(4) the bean hoppers are locked into position bysafetyscrew.Loosenthesafety screwand lift thebean hopper from its mount.
(5)Lift the bean hopperfrom its position. (Holdthe bean gate closed while removing the bean hopper.)
Remove bean hoppers
(6) with a small brush, clean the burr chamber.
Vacuum
(7)Vacuumcoffeefragmentsand loose grounds from the burr chamber.
EN17
Strofinare
(8) wipe the inside of the beanhopperwithasoftcloth to remove coffeeoils.
(9) Repeat for both right andleftbeanhoppers.
(10) Reassemble unit. Do not operate without
bean hoppers in place and safety screwstightened.
WARNINGDO NOT OPERATE WITHOUT
BEAN HOPPERS IN PLACE AND SAFETY SCREWS TIGHTENED
EN 18
Holdshaftlockfirmly
(3)Press and hold the shaftlock to prevent the shaftfrom turning.
(4) With your thumb andforefinger, press againstthe impeller flats. Turnthe impeller clockwise,as viewed from below, to remove.
Remove the reverse-threaded
impeller
tamper cover lid removal
(2)Liftoffthetampercover lid.
(1) Disconnnect the Swift epSb from its power sup-ply.
10. impeller
HAZARDOUS VOLTAGE DISCONNECT FROM POWER
SUPPLY BEFORE SERVICING
WARNING
EN19
Clean impeller Cleanportafilterengagement
(5) with the impeller out, clean around the bayonet ring with thebrush and wipe loose grounds from this area. insert the cleaning brush intothecoffeecollectionarea above the impeller and again wipe loose groundsaway.Cleantheimpellerwith a soft,drycloth.
(6) Reinstall the impeller by turning counterclockwise.
(7) Reconnect the Swift epSbtoitspowersupply.
EN 20
11. Burr Change-Outperiodic burr replacement is required. while the ceramic burrs used in the Swift epSb have a much longer life expectancy than normal
steelburrs,itisstillnecessaryto watch your coffee forthe tell-tale signs of burr wear. these signs include inconsistent shot extraction
times, and the absence ofnoticeablechange in yourespresso when adjustments are made to the grinder.
Remove upper screws (2)Remove lower screws (2) Liftoffcover
(1) Close the bean gates and grind out remaining coffee.
(2) Remove both bean hoppers (see pages 13-15).
(3) Remove the four screws holding the tamper cover in place, and lift off thetamper cover.
(4) Slide the two grind adjustor knobs from theshafts.
WARNINGHAZARDOUS VOLTAGE
DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
EN21
Remove screws
Liftoffcover
(6) Remove adjustor clamp from grinder head and remove adjustingmechanism.
Loosen adjustor clamp
Removeadjustingmechanism
(5) Remove the four perimeter grinder cover screws.Liftoffcover.
EN 22
(7) Rotate burr collar severalrevolutionscounterclockwise,untilfree.
Liftoff
Rotate
(8) Remove the three burr mounting screws fromboth upper and lower burrs.
Remove upper screws
Remove lower screws
EN23
wipe clean
(9) Clean burr engagement surface with a towel or brush.
Positionburr
Vacuum
(11) install new burrs. Do not over-tighten screws, andbe sure no debris is leftunder the burrs.
(12) Reassemble. Use a small amount of food grade grease on the upper burr mount threads when reinstalling.
(10) Vacuum the burr chamber.
EN 24
12. Chute Clean-Out toolOccasionally the chutebetween the grinders and tamping chamber maybecome clogged, causing thefuse (resettable orreplacable)totrip.Inaddition
to replacing or resettingthe fuse, it is important to remove the clogged grounds. On machines with serial numbers above 656, a chute clean-out tool is included.
this tool is used to loosen compacted grounds and alleviate clogging.
(1) Clean out the hoppers and burr chambers as described on pages 13-15.
(2) Remove tamper cover as described on p. 18.
(3) find the holes located on either side of the lower grounds chamber.
(4) insert the long end of the clean-out tool into the hole. Repeat on other side.
(5) Reassemble machine.
WARNINGHAZARDOUS VOLTAGE
DISCONNECT FROM POWER SUPPLY BEFORE SERVICING
Liftoffcover insert tool into chute hole
EN25
Remove screws (2) pull outpull down
(1) Disconnect the Swift epSbfrom its power supply.
(2) Access the fuse area byremoving the two screws located at the lower part of the rear panel door. Do not remove the ground wire screw on the rear panel door.
(3) pull the panel door down and away, thenunplug the ground wire, to expose the controlelectronics.
The Swift EPSbhas fourfuses located at the rear of the machine behind the removable panel. these correspond to each of the grinder motors, the tamping motor, and the electronic controls.Occasionally itmaybe necessary to replace afuse. when switching fuses
besuretouseonlycorrectlyrated replacement fuses. electronics = 1 ea. @ 125m amps (normal); motor, grinder = 2 ea. @ 10 amps GDC;motor, tamper = 1 [email protected] machines with serial numbers 656 and higher, the 10 amp motor fuses are
replaced with reset switches ontheexterorofthegrinder.the head of the switch will protrude when it needs to be reset.Note: See page 31-32 for fuse sizesandlocations.
13. fuse Replacement and Reset Switches
WARNINGHAZARDOUS VOLTAGE
DISCONNECT FROMPOWER SUPPLY BEFORE
SERVICING
EN 26
Replace cover(5) Replace the damaged
fuse with the correctlyrated fuse. (See electrical schematic,page31-32)
(4) Remove the fuse using thetoolprovided.Note:Adamagedfuseisidentifia-ble by a broken filamentand discoloration of thefuse glass.
(6) Replace cover andscrews.
(7) Reconnect power. turn on and resume use.
EN27
14. Tips and TroubleshootingWhat is the ideal shot time?Shottimevarieswithallroastsand brew temperatures used tobrewespresso.Mostlikely,a minimum shot time is 18seconds and a maximumis somewhere in the 30 to 35 second range. the ideal brew time for your coffeedependsthecoffeeroastanddose size. It is a relationshipof bean solids and oils plus tamping pressure and brew water temperature. Most ofall, personal taste preference shouldcontrolshottime.After brewing, re-engagethe portafilter in the group.Temperature stability at theportafilterwill result inmore
consistent pour times. Theportafilter mounting area isa source of heat which can benefit the brewing processwhen used to keep theportafilterattemperature.
Cleangroupsandportafiltersdaily.Clean espresso contact surfaces (screens and inserts) will result in better flavoredcoffee.
Limit rinsing from the grouphead to one second or less. Excessively rinsingthe portafilter reduces theamount of hot water available for brewing. An infusion of cold water into the brewing
vesselmaytemporarilylowerwater temperature below the desired level. Since rinsing is usuallyundertakenasawaytocleantheportafilter,considerwipingtheportafilterinstead.Ifyoumustrinse,dosowithaslittlewateraspossible.Watch the espresso youare brewing. Although making espresso is partlya mechanical process, the outcome is determined byorganicfactorslikethecoffee,the weather, the water, and yourabilitytobalancethese.Defining and adhering to aset of fixed parameters likebrewtimeandshotsizehelpsto ensure a beautiful shot.
However, ultimately the lookand taste of the espresso is the final arbiter of ashot’sacceptability. You mustdeterminewheneverythingisjust right.
EN 28
Message SolutionMessage- Checkthattheelectricalplugisfullyinserted- Switchtheon/offswitchtotheonposition(thelightshouldbelit)*Checkfuses.
- Theportafilterisnotfullyengaged-Theportafilterisalreadyfull- Thetamperisstuckinthefullorupposition(seetampercleaninginstructions)- Thesafetytimerhasrunoutduetoandemptybeanhopper,closedbeangate,orapluggedbean
hopper chute.*Safetymicro-switchfaulty*Safetymicro-switchrodisnotcontactingtheswitchproperly.
- Checkthatthebeanhoppergateisfullyopen- Grindcoarsenessmaybetoofine- Checkpassagebelowbeanhopperforobstructions*Adjustgrindtimereostat.
- Checkforblownfuse(seemanualunderfusereplacement)- Ifagrindermotorfuseisblownreplaceitwitha10ampGDCfuse- Beforestartingthegrindermotorremovethebeanhopper(seemanual)andensurethatthemotor
spinsfreely.Ifitdoesnotspinfreelyfollowtheburrchambercleaninginstructionsandlookforforeignobjects:nail,paperclip,rock,penny,etc.
- Presstheresetbuttonthatcorrespondswiththemotorthatdoesnotrun- Iftheresetbuttonpopsoutagain,turnthegrindadjustknob4rotationsinthefasterpourdirection,
insert the clean out rod (see manual) remove the clean out rod, and restart the grinder.- Iftheresetbuttonpopsoutagain,removethebeanhopper(seemanual)andensurethatthemotor
spinsfreely.Ifitdoesnotspinfreelyfollowtheburrchambercleaninginstructionsandlookforforeignobjects:nail,paperclip,rock,penny,etc.
- Donotattempttoresetthebreakermorethantwiceasthisactionmayoverheatanddamagethetriacon the main power board.
*Swap the power leads between the two motors to troubleshoot motor and triac.
Adjustfinishheightofimpeller.
Adjustfinishheightofimpeller.Change worn burrs.
PushstartbuttonsandNOTHINGhappens.
PushthestartbuttonandtheLIGHTSFLASH
GrindTIMEOUTisreachedbeforebasketisfull.
OneGRINDINGMOTORdoesnotrun(serial numbers 0-655)
OneGRINDINGMOTORdoesnotrun(serialnumbersafter656)
Shotgushesoutatfirstandthenslowsdown
Inconsistentshottimes
tROUBLESHOOtiNG GUiDE (* items are for techs)
EN29
1ON/OFFSWITCH
GREE
N
CAP.
GRIND
ERMO
TOR
BLACK
WHITEWHITE
RED
YELL
OW/G
REEN
YELLOW/GREEN
WHITE
RED
WHITE
BLACK
MOTO
RTA
MPER
CAP.
WHITE
WHITERED
BLACK
WHITE
2BL
ACK
GRIND
ERMO
TOR
CAP.
3 4
RIGHTLEFT
P2
TAMPERTIME DELAY OFF
P
TIME-OUTGRINDER
RED
PORTA-FILTER INLIMIT SWITCH
WHITE
FULL LIMIT SWITCH
WHITE
BLUE
FUSE NO.
1
2
34 GRINDER MOTOR
TAMPER MOTOR
GRINDER MOTOR
TRANSFORMER
10A TIME DELAY1A TIME DELAY
10A TIME DELAY
125mA FAST ACTING
FUNCTION CONTROL AMPERAGE
115 VAC 230 VAC
115/230 VAC
15. Electrical DiagramsSerial numbers up to 655
EN 30
1115/230 VAC ON/OFF
SWITCH
GREE
N OR G
REEN
/YELL
OW
CAP.
GRIND
ERMO
TOR
BLACK
REDWHITE
RED
YELL
OW/G
REEN
YELLOW/GREEN
WHITE
RED
RED
BLACK
MOTO
RTA
MPER
CAP.
WHITE
WHITERED
BLACK
WHITE
2
BLAC
K
GRIND
ERMO
TOR
CAP.
RED
PORTA-FILTER INLIMIT SWITCH
WHITE
FULL LIMIT SWITCH
WHITE
BLUE
FUSE NO.
1
2 TAMPER MOTOR
TRANSFORMER
1A TIME DELAY
125mA FAST ACTING
FUNCTION CONTROL AMPERAGE
115 VAC 230 VAC
10 AMPMANUAL
RESET
10 AMP
RESETMANUAL
COUNTER
BLACK
BLAC
K
TIME DELAY OFF
LEFT
P
RIGHT
P2
TIME-OUTGRINDER TAMPER
Serial numbers 655 and above
EN31
Change of grinding discs1.Disconnect power supply
from the coffee machine,stopbeanflowing into thegrinder and if necessarydismantle the grinder.
2. Release clamp [1] and remove it.
3.Turnstationarydiscsflange[3]anti-clockwiseandtakeitoff.
4. Unscrew the grinding discs (3 screws [4]) from the stationary- and rotary discflanges.Dohold/block the
rotarydiscflange[4a]withaplastictool.
CleaningUse a brush to clean the surfaces of the flanges.Removeallcoffeeparticlesordust from the thread and than lubraca-te it with slight film(spray)ofPanolinTEFGREASEH1, prod. 5975, food grade, NSf listed; www.panolin.com
5. insert new grinding discs on the cleaned rotary- /stationarydiscflan-gesandtightenscrewscarefully.
6. Re-install the statonarydisc flange [5] clock-wise(avoid touching of the grinding discs).
7.Connectpowersupply.8. Calibrate grinder.
important: All surfaces of the grinding discs as well as theflangesmustbeproperlycleaned in order to ensure a perfect grinding.
16. Cleaning Procedure
EN 32
17. Recycling1) De-commissioning and demolitionStart by setting themain switch to the“0”orOFFposition.Disconnecting from the power outletDisconnect the Swift epSb from the electrical network by switching off theassociated circuit breaker or circuitprotection device. Remove the powersupplycordfromthepowerconnection.
At this point, the machine may beremovedfromthebar,beingverycarefulnottodropitorsquashyourfingers.
the machine is made out of various materials and therefore, if you do notintend toput it back in service, itmustbe taken to a special disposal companywhich will select the materials which can berecycledanddiscardtheothers.Current regulations make it illegal todiscard such machine by leaving iton public grounds or on any privateproperty.
Recycling notice: Warning for the protection of the environment.Used electrical and electronic waste contains hazardous but also valuableand scarce materials which should be recovered and recycled properly. Wekindly ask that you contribute to theprotection of the environment andnatural resources by delivering usedequipment to the relevant recyclinglocationsifsuchlocationsareavailableinyourcountry.