Manual Fixed Pulverizer
-
Upload
yousef-alipour -
Category
Documents
-
view
224 -
download
0
Transcript of Manual Fixed Pulverizer
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 1/24
MYUNGSAN HYDRAULIC PULVERIZER
OPERATION AND PARTS MANUAL
MYUNGSAN SAN
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 2/24
1
Congratulations on your joining as a
MYUNG SAN customer Myungsan pulverizer have been developed based on the long year’ s accumulatedexcellent design technologies. Several years field test ensures its durability and high
performance. However, the customer is kindly requested to read this manual and tounderstand necessary instructions for the safe and long life usage. Any troubles caused
by improper maintenance, abnormal usage and repairs using non-genuine spare parts
can not be covered by warranty claims.
WARRANTY INFORMATION
WARRANTY is provided as part of the Myungsan support program for customerswho operate and maintain their equipment as described in this manual. Should theequipment be abused or modified to alter its performance beyond original
specifications, the warranty will become void. Setting the carrier hydraulicpressure above specification or changing the size of the attachment cylinder toincrease performance will also void warranty.
SAFETY FIRST
It is the responsibility of the operator
and service technician to read rules andinstructions for safe and proper
operation and maintenance.
A cautious worker using common sense
is the greatest safety device.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 3/24
2
CONTENTS
CHAPTER 1. PRECAUTIONS AND SAFETY SYMBOLS ………. ………. …...3
1.1 PRECAUTIONS
1.2 SAFETY SYMBOLS
1.3 LABEL LOCATIONS
CHAPTER 2. SPECIFICATIONS …………………………………………………..9
CHAPTER 3. EXTERNAL DIMENSIONS ……………………………………….10
3.1 MS850F
3.2 MS1000F
CHAPTER 4. INSTALLATION …………………... ……………………. ………..11
4.1 GENERAL VIEW OF PULVERIZER
4.2 HYDRAULIC CIRCUIT
4.3 PULVERIZER MOUNTING PROCEDURE
4.4 PULVERIZER REMOVAL PROCEDURE
CHAPTER 5. OPERATION AND MAINTENANCE ………. ……………. ……15
5.1 PRECAUTIONS FOR SAFE OPERATION
5.2 MAINTENANCE
CHAPTER 6. TROUBLE CAUSE AND REMEDY………. ……………….. …..20
CHAPTER 7. EXPLODED VIEW AND PARTS LIST ……. …………….. ……2 1
7.1 EXPLODED VIEW
7.2 PARTS LIST
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 4/24
3
CHAPTER 1. PRECAUTIONS AND SAFETY SYMBOLS
1.1 PRECAUTIONS
The Myungsan Hydraulic Pulverizer can operate safely and normally if it is operated in
accordance with instruction given in this manual. Read this manual thoroughly beforeoperation. If operator do not understand necessary instructions completely serious
personal injury or equipment damage can occur.
(1) Observe all laws and regulations that affect you and your equipment when youoperate the pulverizer.
(2) Read the excavators operation manual and understand the safety and operation
instructions completely.
(3) Check all the necessary maintenance procedures are completed.
(4) The operator should quit the operation immediately if anyone moves in the working area which is much larger than that of excavator due to the risk of flying debris.
(5) Before leaving the excavator, set the boom lower position and insure the excavator is
stable. Never leave the excavator while the engine is running. Fasten the parking brake.
(6) Stop the engine when you want to repair or adjust the pulverizer.
(7) Keep temperature of the working fluid of excavator between 20 oC ~ 80 oC for
proper performance.
(8) To avoid personal injury and crusher damage genuine parts of Myungsan should be used. Also, only the authorized person or well trained person should repair the
pulverizer.
(9) Keep this manual near operator.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 5/24
4
(10) Do not operate this pulverizer when you are under the influence of drug or alcohol.
(11) Detach pulverizer from excavator during transport.
(12) Observe the excavator manufacturer’ s safety regulations.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 6/24
5
1.2 SAFETY SYMBOLS
Your safety and the safety of others is a result of how you operate and maintain your
equipment. Read and understand this manual and other safety information providedwith the carrier machine. Carefully read all safety messages in this manual and on your
equipment safety signs. Keep safety signs in good condition, replace missing or damaged safety signs.
Understand signal words
Indicates immediate hazards which will results in severe personal injury and death.
Indicates hazards or unsafe practices which could result in severe personal injury or
death.
Indicates hazards or unsafe practices which could result in damage to the machine or
personal injury.
GREASING
Indicates to fill cavity with recommended grease through the grease nipple before use.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 7/24
6
1.4 LABEL LOCATIONS
ITEM DESCRIPTION
1 GREASE DECAL- one at each grease fitting
2 DANGER DECAL-1-one on front side of body
3 DANGER DECAL-2-one on back side of body
4 LOGO DECAL-one on front side of body
5 MODEL DECAL-one on back side of body
6 MODEL and SERIAL NUMBER plate-one on upper front side of body
7 WARNING DECAL – one on upper back side of body
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 8/24
7
ITEM 1 GREASE DECAL
ITEM 2 DANGER –1 DECAL
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 9/24
8
ITEM 3 DANGER-2 DECAL-2
ITEM 6 MODEL and SERIAL NUMBER PLATE
ITEM 7 WARNING DECAL
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 10/24
9
CHAPTER 2. SPECIFICATIONS
Cylinder
Weight(kg) Max. Working
Pressure(Bar)
Flow Rate
(lpm)
Cylinder Force(tons)
Base Excavator (tons)
MS850F 1,800 320150
~250
100 17~25
MS1000F 2,400 320180
~
300
121 25~40
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 11/24
10
CHAPTER 3. EXTERNAL DIMENSIONS
3.1 MS850F
3.2 MS1000F
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 12/24
11
CHAPTER 4. INSTALLATION
4.1 GENERAL VIEW OF PULVERIZER
No Name
1 Hydraulic Pump
2 Oil Tank
3 Main Control Valve
4 Direction Control Valve for Cylinder
5 Direction Control Valve for Swing Motor
6 Pedal Switch
7
Electric Fuse
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 13/24
12
4.2 HYDRAULIC CIRCUIT
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 14/24
13
4.3 PULVERIZER MOUNTING PROCEDURE
1. Place the pulverizer on the ground(or wood block) with blocking to keep the
pulverizer level for installation.
2. Remove the bucket or other attachment following the manufacturer’ s recommended procedure.Be careful not to contaminate the hydraulic system by plugging the hydraulic hoses.
3.
With the jaws of the crusher facing the excavator, operate the excavator into proper
position, lining the excavator’ s arm(second boom) into the top bracket pivot of the pulverizer.
4.
Pin the excavator’ s arm and crusher top bracket pivot together.
5. Pick the pulverizer up into a proper position where the second linkage pin can beinserted. Insert pin.
5.
Connect the hydraulic hoses to the manifolds(or fitting) located on each side of the top. Tighten the bolts or cap to the proper torque.
When installation is complete, fully extend excavator bucket cylinder to curlcrusher. Check for interference. Contact factory or authorized dealer if any
interference occurs.
7.
Lift the boom and slowly try the pulverizer open and close function. Watch for
hydraulic oil leakage.
Observe flow rate and pressure range or the warranty will become void.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 15/24
14
4.4 PULVERIZER REMOVAL PROCEDURE
1. Position the pulverizer under the boom of the excavator.
Trapped hydraulic pressure may be present after base machine is turned off.
Extreme caution must be taken when removing crusher hydraulic hoses or possibleinjury or death could result.
2.
Disconnect the hydraulic hoses. Be careful not to contaminate the hydraulic system by plugging the hydraulic hoses.
3.
Remove the bucket cylinder pin from the pulverizer mounting bracket.
4.
Remove the arm pin of the excavator from the pulverizer mounting bracket.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 16/24
15
CHAPTER 5. OPERATION AND MAINTENANCE
5.1 PRECAUTIONS FOR SAFE OPERATION
(1) Check the excavator position is stable.
(2) Do not use pulverizer like a lever.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 17/24
16
(3) Do not pull or push object with pulverizer when cylinder is acting.
(3) Do not hit the pulverizer against the object.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 18/24
17
(5) Inadequate operation can cause damage to the cylinder rod.
(6) Operate carefully not to hit the excavator with the pulverizer
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 19/24
18
5.2 MAINTENANCE
Inspection Items Check Points and Remedy
1. Bolts, Nuts, Snap-Ring, etc -Looseness, damage, missing
à Tighten, replace
2.
Cylinder-Rod -Damage on the surface of cylinder rod.
à Surface finishing or replace
3.
Cutter
-Damage, gap more than 1mm due to
wear, breakage, and or bolt loosenessà Replace or tighten the bolts
4.
Pins, Bush
-Gap more than 1mm due to heavy wear or
breakageà Replace
5. Grease -Grease every 4~8 working hours
6. Damage on the structure -Check crack, breakage, damageà Repair
7.
Oil leakage -Check piping and sealsà Tighten, Replace seals
8.
Pressure setting -Check main relief pressureà Adjust relief valve(280~300 bar)
9.
Fluid contamination -Check fluid(oil) contamination regularlyà Replace oil and filter
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 20/24
19
RECOMMENDED LUBRICANTS
For normal operating conditions, periodic lubrication with lithium Grade 2 extreme
pressure grease is recommended. For operation below 0o
C (32 o
F), Grade 0 isrecommended.
Comparable lubricants produced by other reputable manufacturers not referred belowmay also be used.
Maker Trade Name
For Operation Below
0o C (32 o F), & Forstorage
For Operation Above
0o C (32 o F)
AMOCO
CHEVRONEXXONMOBIL
SHELLSOHIO
SUNTEXACOUNION
Rycon
Dura LithLidok
Mobilux
AlvaniaBearing Guard
PrestigeMultifak Unoba
EP0
EP0EP0EP0
EPR0LT0
740EPEP0EP0
EP2
EP2EP2EP2
EP22
742EPEP2EP2
PULVERIZER STORAGE
1. Block the crusher up off the ground using wood blocking.
2. Grease the pins and machined bores of the mounting bracket of the attachment. Thenapply a generous amount of grease to shear blades, cylinder rod and all other exposedand unpainted surfaces.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 21/24
20
CHAPTER 6. TROUBLE CAUSE AND REMEDY
Trouble Phenomena
Cause Remedy
1. Cylinder do not
operate
1.1 Electric shortage.
1.2 Sticking in solenoid valve.
1.3 Working fluid(oil) do not
flow.
1.4 Damage of seal of Cylinder.
à Check battery or electric wire. Connect wire.
à Repair solenoid spool or replace with new one.à Check the piping(turn on
stop valve).
à Replace damaged seal.
2. Oil leakage fromCylinder
3.1 Seal damage. à Replace with new one.
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 22/24
21
CHAPTER 7. EXPLODED VIEW AND PARTS LIST
7.1 EXPLODED VIEW
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 23/24
22
7.2 PARTS LIST
7.2.1 MS850F
No Name Part No Quantity Remark
1 PIN-TOP MF0100100 1 x 2
2 BUSH-T MF010020A 1 x 4
3 ELBOW MF0100300 1 x 2
4 PLUG-B MF0100400 1 x 6
5 PIN-CYLINDER MF010050A 1
6 BOLT MF0100600 36 M16, L=60 7 BUSH-BC MF010070A 2 x 2
8 BUSH-B MF010080A 1 x 2
9 BUSH-T MF010090A 1 x 2
10 PIN-TOOTH MF010100A 1
11 BUSH-CT MF010110A 1 x 2
12 BEARING MF010120A 1 SB95Α
13 BUSH-C MF010130A 1 x 2
14 CUTTER MF010140A 1 x 2
15 BOLT MF0101500 6 M16, L=40
16 BODY MF0101600 1
17 TOOTH MF010170A 118 CYLINDER MF010180A 1
19 DUST SEAL MF010190A 1
20 DU-BUSH MF010200A 1
21 U- PACKING MF010210A 1
22 BACKUP RING MF010220A 1
23 O-RING MF010230A 1
24 BACKUP RING MF010240A 1
25 BUFFER RING MF010250A 1 x 2
26 PIN-BODY MF0102600 1
27 U- PACKING MF010270A 1 x 228 BACKUP RING MF010280A 1 x 2
29 O-RING MF010290A 1
30 HOSE MF0103000 1 x 2
31 O-RING MF0103100 2
32 FLAGE-HALF MF0103200 2 x 2
33 BOLT MF0103300 8
34 WASHER MF0103400 8
7/25/2019 Manual Fixed Pulverizer
http://slidepdf.com/reader/full/manual-fixed-pulverizer 24/24
7.2.2 MS1000F
No Name Part No Quantity Remark
1 PIN-TOP MF0200100 1 x 2
2 BUSH-T MF0200200 1 x 4
3 ELBOW MF0200300 1 x 2
4 PLUG-B MF0200400 1 x 6
5 PIN-CYLINDER MF020050L 1
6 BOLT MF020060L 36 M16, L=60
7 BUSH-BC MF020070L 2 x 2
8 BUSH-B MF020080L 1 x 2
9 BUSH-T MF020090L 1 x 2
10 PIN-TOOTH MF0201000 1
11 BUSH-CT MF0201100 1 x 2
12 BEARING MF0201200 1 SB100A
13 BUSH-C MF0201300 1 x 2
14 CUTTER MF0201400 1 x 2
15 BOLT MF0201500 6 M16, L=40
16 BODY MF0201600 1
17 TOOTH MF0201700 1
18 CYLINDER MF0201800 1
19 DUST SEAL MF0201900 1
20 WEAR RING MF0202000 1 x 321 ROD PACKING MF0202100 1
22 BACKUP RING MF0202200 1
23 O-RING MF0202300 1
24 BACKUP RING MF0202400 1
25 O-RING MF0202500 1
26 PIN-BODY MF0202600 1
27 PISTON PACKING MF0202700 1 x 2
28 BACKUP RING MF0202800 1 x 2
29 O-RING MF0202900 1
30 HOSE MF0203000 1 x 231 O-RING MF0203100 1 x 2
32 FLAGE-HALF MF0203200 2 x 2
33 BOLT MF0203300 8
34 WASHER MF0203400 8