OPERATORS MANUAL

HEAVY DUTY TABLESAW by INVICTA

ModelRT-40

INVICTA USA English Version (877) 308-6423 - East (800) 499-4682 - West

1

Table Saw Mod. RT-40

General Instructions Thank you for purchasing this quality machine from INVICTA. As with all equipment, safety is to be the priority. The operator should understand the safety features as well as apply good safety habits in transportation, adjustment, maintenance and operation of the machine. Practice and teach others the safe operating procedures of this machine and help to prevent the possibility of accidents. Safety Rules

1. For your own safety, read carefully the Instruction Manual before attempting to operate the machine. 2. If you are not thoroughly familiar and comfortable with the adjustment and operation of the machine, ask for

instruction from your supervisor or a fully qualified person. You may also contact Invicta USA. 3. Before the initial operation of the machine, remove all packaging, shipping grease and fully assemble the

machine. Pay special attention to the assembly of safety components. 4. Wear proper apparel while operating the machine. Never wear loose fitting clothing, gloves or ties. Always

remove rings or other jewelry before operating the machine. It is strongly suggested the operator wear shoes with non-slip soles and also wear a protective hair net to prevent hair entanglement in moving parts.

5. Always wear personal safety equipment. Follow the safety regulations of your country and your company. 6. Have a certified person make all wiring connections to power source and properly ground the machine. 7. Always disconnect the machine from the power source and use lockout procedures before servicing,

changing cutting tools and during cleaning of the machine. 8. Before starting the machine, have the work area clean and free of debris. Cluttered areas are invitations for

accidents to occur. 9. Keep the safety guard(s) of the machine in place and in proper working condition. Never operate

machinery without safety equipment in place. Report any damage to your supervisor. 10. Keep children and visitors a safe distance from the working area. 11. Never leave the machine running while unattended. Turn off the power source during breaks. The machine

should come to a complete stop before walking away. 12. Do not operate the machine under the influence of drugs or alcohol. Consult your physician when taking

medications. 13. Do not force the machine beyond its limitations. It will produce a nicer and safer job at the rate it was

designed to operate. Additional Safety Rules for the Operation of Table Saws 1) Avoid Kickbacks. “Kickback” can occur when the workpiece is forced back by the saw blade during improper operation. When “Kickback” occurs injury can result. Some causes of Kickback are: A- Dull blades or an improperly adjusted fence in relation to the blade.

B- Knots, Nails or Imperfections in the workpiece. C- Heavier cutting than the machine was designed for.

D- Failure to use a pusher block when cutting thin or narrow workpieces. 2) Never start the work-piece into the blade before allowing it to reach full operation speed. 3) Use the correct tooth style and rake for the material you plan to cut. 4) Keep the Blade sharp and free of rust and pitch 5) Use good safety habits when using dado blades. 6) Support and control the workpiece properly all times during the operation. 7) Never reverse the direction of the workpiece after beginning operation. Kickback can occur. 8) Definitions of ripping, crosscutting and dadoing of the workpiece:

A- Ripping operations: Cutting the material in the same direct as the flow of the grain. B- Crosscutting operations: Cutting the material across the grain. This may produce heavy splintering. C- Dado operations: Cutting a flat-wide bottom grove in the material.

2

Table Saw Mod. RT-40

Loading and Unloading

Fig.01 Never load or unload the machine by any component that could be damaged. Transporting the machine by the directions in Fig.01 is the recommended procedure. After placement has been completed, remove all the protective grease or varnish from the machined surfaces using kerosene or a similar solvent. Installing the machine On a solid surface, level the machine (Fig.02) then add all attachments such as the blade guard and fences. Connecting Electricity Each machine is provided with a reference plate that indicates the requirements for electrical service needed for the machine to operate property. Before you call a certified electrician to make the wiring connections, be sure that the voltage and cycle (phase) stated on this reference plate are the same as provided in your building. (Electrician) Remove the electrical box cover and connect the electrical supply wires to the proper terminals. Rapidly turn on and off the machine and then visibly check the rotation direction of the saw blade. It should rotate so as the top of the exposed blade travels toward the operator’s position while sawing. See page 7 For changing blade direction for three-phase machines: invert two wires of the power source without changing the internal connections of the machine. Should further information be needed please contact Invicta USA. IMPORTANT: If your machine is equipped with a star-triangle switch (Y∆), first turn it to the start position and when the motor reaches its maximum speed turn it immediately to the triangle position. Never operate the machine with the swich in the start position or damage may occur. Lubrication

730

600±

2100

760

630±265

100

LEVELM12 x 1,7515

0 70

3525

Fig.02

Your machine requires periodic lubrication as follows: Points “A” (pgs 07 and 08) should be cleaned with kerosene and lubricated with common grease as required. The saw shaft bearings do not required lubrication as they are sealed for life.

3

Table Saw Mod. RT-40

Controls 1. ELECTRIC SWITCH (pag. 07) 2. SAW TILT ADJUSTMENT HANDWHEEL (pag. 07) This handwheel is used to adjust the tilt angle of the saw from 0º to 45º. To adjust this feature, loosen lock knob nº 4 then turn the handwheel nº 2 until the desired angle is obtained, relock. The angle is read on scale nº 5 3. SAW BLADE HEIGHT ADJUSTING HANDWHEEL (pag. 07) This handwheel is used to adjust the amount of blade that protrudes through the top of the material. Before moving the handwheel, loosen lock knob nº 6, then relock after the adjustment is completed. Rip Fence Alignment The relationship between the rip fence and the blade assembly has been aligned from the factory. Should the fence require adjustment due to shipment, please follow the procedure below. First loosen or tighten nuts nº 11 as needed until the desired parallel relationship is obtained between the saw blade and the rip fence. Never adjust the rip fence so that the distance between the blade and fence on the output end is less than on the input end. This slightly greater distance at the output side of the blade will decrease the possibility of pinching or binding of the material. Rip Fence Width Adjustment Proceed as follows: First loosen lock lever nº 7 and turn knob nº 8 until the desired adjustment is obtained. Relock by lever nº 7. The width of the cut is read on scale nº 9. To obtain the longitudinal adjustment of the guide it is necessary to loosen the two knobs nº 10, retightening after adjustment. Scale Pointer Adjustment (page 07) The scale pointer may need occasional adjustment due to variations in saw blade kerfs. When adjustment is necessary, proceed as follows: First, disconnect power supply then slide the rip fence gently against the saw blade. Loosen knob nº 13 and adjust the pointer to zero on scale nº 9 to zero. Complete the adjustment by locking nº 13. Adjustment of the tilt limit stops (page 07) These stops are designed to give the blade an exact locator for 0º and 45º. These stops have been adjusted at the factory. If later adjustment is necessary: place a precision square against the blade and adjust to 0º, loosen nut nº 14, and adjust acrew nº 15 until the blade stops at the correct position. Tighten nut nº 14. Follow the same procedure for the 45º adjustment. Vertical Saw Blade Adjustment (page 07)

Stops nº 16 limits the maximum and minimum height travel of the blade. These stops have been adjusted at the factory. If future adjustment is necessary, loosen nuts nº 17 and adjust screw nº16 to increase or decrease the blade travel. Once positioned, tighten nº 14 nuts. Do Not use a blade that is larger than specified.

4

Table Saw Mod. RT-40

Saw Guard Adjustment (page 07) Saw guard/blade slitter adjustment is by handle nº 18. The saw guide/blade slitter support is adjusted by nuts nº19, and should be readjusted according to the saw blade diameter each time the blade is changed. Belt Tension Adjustment (page 08) To adjust belt tension or change belts, loosen screw nº 20 and adjust as necessary. Tighten screws. Procedure for Changing the Saw Blade (page 08) Remove the saw guard by loosening the lock handle nº 18. Remove the table blade insert (item nº 21) and depress the blade locking pin (item nº22). Loosen nut nº 23 with the special wrench supplied with the machine. Change to the desired blade. Keep all collars clean and free from burrs. Reassemble all components. (Note spindle has LH thread.) Table Insert Adjustment (page 07) The table insert is adjusted at the factory for perfect flush alignment with the top of the table. Should future adjustment be needed, make adjustments by screws nº 24. Miter Fence (page 08) The miter gauge is designed to control the angle of the wood material as it is sawn. The angle is adjusted as follows: Loosen locking handle nº 25 and turn the guide to the desired angle and retighten the locking handle. The cutting angle can be read on scale nº 26. Electrical Protection equipment (page 09) The machine can be optionally supplied with electrical overload protection. This equipment disconnects the motor automatically when there is an electrical overload that could damage it. When the motor is disconnected, it is necessary to reset the therrmal relay by pressing the reset button (point nº 02). Continue by pressing the start button. On pages 9 thru 12 are electrical diagrams for special motorization. Machine Identification and Replacement Parts Every INVICTA machine has a serial number which enables the manufacturer to identify the exact type and date of its manufacture. At the end of this manual you will find a list of parts which compose your machine with their names and numbers. Use only genuine INVICTA parts and on your order always mention the serial number, part number and quantity desired.

5

Table Saw Mod. RT-40

Technical Data Standard saw blade diameter……………………………….………………………………… mm 350 (14”) Maximum saw blade diameter………………………………………………………………… mm 400 (16”) Shaft diameter…………………………………………………………………………………… mm 30 Maximum cut (350 mm diameter saw)………………………………………………………... mm 115 (4-1/2”) Maximum cut (400 mm diameter saw)…………………………..…………………………… mm 140 (5-1/2”) Maximum height of cut at 45º (350 mm diameter saw)…………………………………….. mm 80 (3-1/8”) Maximum height of cut at 45º (400 mm diameter saw)……….……………………………… mm 105 (4-1/8”) Motor 3 / phase…………………………………....……………………………………………… HP 7,5 Shaft speed………………………………………………………………………………………. RPM 3000 Maximum dado capacity………………………………………………………………………... mm 40 (1-9/16”) Maximum rip capacity……………………………………………………………………………. mm 850 (33-7/16”) Distance from front of the table to center of the saw blade saw…………………………… mm 580 (22-13-16”) Distance from front of table to the edge of a Ø 350 mm saw at maximum height………… mm 435 (17-1/8”) Height from floor to table top………………………………………………………………….. mm 850 (33-7/16”) Table dimensions……………………………………………………………………………….. mm

inch 1000 x 1000

39-3/8” x 39 – 3/8”

Table dimensions including 2 extensions…………………………………………………… mm 1500 x 1100

59” x 43-5/16” Saw tilt to the right………………………………………………………………………………. º 45º Approx. net weight with motor…………………………………………………………………. kg 543 (1195 Lbs) Accessories 1 Special wrench 1 Instruction Manual

6

Table Saw Mod. RT-40

Instructions for replacing the Sawdust Guard Your machine is equipped with a wooden guard (ballast) that helps to prevent sawdust from being blown up through the table insert. This is a very important feature when dust collection is absent or very poor. Due to normal wear it becomes necessary to change this guard, proceed as follows: Raise the saw blade to its maximum height, remove the table insert. Replace the wooden guard with a new one of the same dimensions. Next, mount the new piece of wood in the guard, and reassemble table insert. Turn the saw on and slowly lower it to its minimum height, executing the cut in the wood. (Always lockout the power supply when doing blade maintenance)

A

7

Table Saw Mod. RT-40

Controls (Adjustment Features #1)

1924

1718

1615

1411

1209 13 08 0710

0306

0502

0401

8

Table Saw Mod. RT-40

Controls (Adjustment Features #2)

2625

2318

2221

A

20

9

Table Saw Mod. RT-40

ELECTRICAL BOX

71

0201 03 04

A1

1 L1

A1

1-2-

2 T1

05 06

A2

96 N

C

PAR

T. N

°

11-2

8-00

230

11-3

4-00

120

11-0

7-00

690

11-3

1-00

070

8NA

E-K

205-

0

11-2

0-00

090

3 L2

A2 5 L3

3NO

4NO

3-

4 T2

4-

6 T3

A2 95 N

C97

NO

98 N

O

5 6

21

ITEM 3

4 13 2

4 5 6S

ingl

e ph

ase

trans

form

er

NA

ME

Ele

ctric

al b

ox

Dis

junt

or C

6A 5

SX1

-1

Con

tact

or C

WM

25

1

QTY

.

1 1

Trac

k

Ove

rload

rela

y R

W27

D

1 2 1

07

1 2

5 6

08

11-0

3-00

150

11-0

3-00

090

11-0

2-00

490

9 10

13 14

17 18

21 22

25 26

87

9

8 9

09

Pre

ss c

able

PG

13.5

Pre

ss c

able

PG

21

Bor

ne te

rmin

al

2 1 1

10

10

11-0

4-00

750

Sw

itch

elec

trica

l

10

Table Saw Mod. RT-40

Three – Phase Motor With overload Protection – 7,5HP – 230 / 460V

11

Table Saw Mod. RT-40

Single – Phase Motor with Overload Protection

12

Table Saw Mod. RT-40

Select Switch – 230 / 460 V

IMPORTANTSELECT THE VOLTAGE (230/460V) OF YOUR INTERNAL ELECTRIC NETWORK.THE VOLTAGE SELECTION KEY IS LOCATED ON THE ELECTRICAL BOX.FOR YOU SAFETY THE VOLTAGE SELECTION KEY IS ON NEUTRAL POSITION.

13

Table Saw Mod. RT-40

Replacement Parts (Blade Guard)

26 25 19

01 02 03 04

10

07 0809

1112

1413

1516

17

05 06

24 23 22 21 20

18

3536

3433

3228

3130

2927

14

Table Saw Mod. RT-40

Replacement Parts (Miter Fence)

37

38

39

40

41

42

43

44 45 46 47 48 49

50

51

52

53

54

55

5657585960

Items 42-60 Assembly Part Number 82SB-K039-0

15

Table Saw Mod. RT-40

Replacement Parts (Saw Arbor)

626185

83

63

79

8280

81

78

6869

70

7677

7172

7375

7473

16

Table Saw Mod. RT-40

Replacement Parts (Saw Cabinet)

86 87 88 89 90 91 9293

9495

9697

9899

105

106

107

108

109

110

111

112

113

104

103

102

101

100

17

Table Saw Mod. RT-40

Replacement Parts (Saw Trunion and Motor)

125

165

119

124

122

123

120

121

117

118

114

115

116

127

126

128

129

130

131

132

133

163

164

162

161

160

159

158

157

134

135

136

137

138

139

142

140

141

143

144

152

154

155

156

153

145

146

147

151

148

149

150

18

Table Saw Mod. RT-40

Replacement Parts (Saw Table Top and Rip Fence)

197

166

167

168

196

195

194

193

192

191

190

189

170

171

172

173

174

175

179

180

181

182

188

187

186

185

183

184

178

177

176

169

198

199

200

201

19

Table Saw Mod. RT-40

Replacement Parts FIG. Nº CODE QTY. NAME FIG. Nº CODE QTY. NAME

01.......... 06-03-0078-0 02…... Allen cap screw M6-1x12 35……... 06-18-0034-0 02….. Snap ring RS9 02.......... 82SB-K200-0 04…... Hinge pin screws 36……... 82SB-K194-0 02….. Kick back finger 03.......... 82SB-K193-0 01…... Guard bar 37……... 27-01-0038-0 01….. Knurled knob 04.......... 82SB-K191-0 04…... Guard arms 38……... 06-02-0053-0 01….. Allen set screw head M6-1,0x10 05……... 26-03-0010-0 01…... Roll pin Ø8x80mm 39……... 8NVL-K181-0 01….. Repeat stop bar 06……... 82SB-K199-0 02…... Hinge pin 40……... 8NVL-K182-0 01….. Repeat stop shaft 07……... 06-02-0068-0 04…... Allen set screw M5-0,8x8 41……... 85SB-K125-0 01….. Repeat stop knuckle 08……... 82SB-K192-0 02…... Side plates * 42…... 82SB-K108-0 01….. Release lever 09……... 8NAR-K134-0 04…... Flat washer Ø30x12x1,9 * 43…... 07-00-0002-0 01….. Spring 10……... 82SB-K198-0 04…... Bushing * 44…... 89SB-KK97-0 01….. Shoulder bolt 11……... 06-06-0029-0 04…... Flat head screw M6-1x12 * 45…... 26-00-0006-0 01….. Roll pin Ø3x16 12……... 06-04-0121-0 02…... Hex head cap screw M10-1,5x30 * 46…... 82SB-KK93-0 01….. Pivot plate 13……... 06-13-0015-0 02…... Flat washer Ø10 mm * 47…... 82SB-K208-0 01….. Miter guide 14……... 82SB-K202-0 01…... Left spacer 3/16” * 48…... 06-03-0056-0 01….. Allen cap screw M5-0,8x12 15……... 82SB-K203-0 03…... Right inner spacer 1,52mm * 49…… 85SB-KK84-0 01….. Indicator bracket 16……... 82SB-K204-0 04…... Right outer spacer 0,9mm * 50…... 06-05-0053-0 02….. Round head screw M4-0,7X10 17……... 06-03-0081-0 02…... Allen cap screw M10-1,5x40 * 51…... 89SB-KK92-0 01….. Miter guide 18……... 82SB-K201-0 01…... Guard block * 52…... 06-17-0002-0 02….. Pop ad 440s rivet 19……... 06-02-0055-0 02…... Allen set screw M8-1,25x20 * 53…... 85SB-KK86-0 01….. Graduated scale 20……... 89SB-K131-0 02…... Washer * 54…... 89SB-KK96-0 01….. Stud 21……... 06-03-0054-0 02…... Allen cap screw M6-1x10 * 55…... 06-13-0026-0 01….. Flat washer Ø10mm 22……... 82SB-K196-0 01…... Guard main shaft * 56…... 89SB-K125-0 01….. Lock knob 23……... 06-09-0019-0 02…... Hex nut M6-1,0 * 57…... 89SB-K106-0 01….. Guide pin 24……... 82SB-K188-0 01…... Shaft support * 58…... 89SB-K107-0 01….. Guide bushing 25……... 06-02-0054-0 01…... Allen set screw M8-1,25x10 * 59…... 89SB-K126-0 01….. Lever pin 26……... 06-13-0002-0 02…... Flat washer 1/4” * 60…... 27-00-0004-0 01….. Knurled knob 27……... 06-04-0096-0 02…... Hex head cap screw M6-1,0x25 61……... 82SB-K116-0 01….. Hex head bolt 28……... 06-09-0019-0 04…... Hex nut M6-1,0 62……... 82SB-K114-0 01….. Shaft end cap 29……... 06-13-0002-0 04…... Flat washer 1/4” 63……... 8NFL-KK34-0 01….. Inner saw flange 30……... 82SB-K197-0 01…... Support bracket 64……... 31……... 06-13-0002-0 04…... Flat washer 1/4" 65……... 32……... 06-04-0095-0 04…... Hex head cap screw M6-1,0x20 66……... 33……... 82SB-K185-0 01…... Guard base 67…….. 34……... 82SB-K195-0 01…... Pin 68…….. 06-18-0017-0 01….. Snap ring I62

* 82SB-K039-0 Miter gauge assembly

20

Table Saw Mod. RT-40

FIG. Nº CODE QTY. NAME FIG. Nº CODE QTY. NAME 69…….. 82SB-K221-0 01….. Blade arbor 105…… 82SB-KKK2-0 01….. Upper saw base 70…….. 82SB-KKK9-0 01….. Bearing housing 106…… 11-28-0021-0 01….. Electrical connection box 71…….. 06-13-0015-0 03….. Flat washer Ø10mm 107…… 06-04-0121-0 04….. Hex head cap screw M10-1,5x30 72…….. 06-04-0098-0 03….. Hex head cap screw M10-1,5x35 108…… 82SB-KK11-0 02….. Saw trunion support 73…….. 03-00-0033-0 02….. Bearing 6206 2RS 109…… 26-02-0001-0 04….. Roll pin Ø6x20 74…….. 8NAR-K104-0 01….. Washer 110…… 8NAR-KK98-0 04….. Washer Ø25x10,5x3,1 75…….. 06-04-0099-0 01….. Hex head cap screw M12-

1,75x30 111…… 06-04-0125-0 04….. Hex head cap screw M10-1,5x20

76…….. 8NPM-K158-0 01….. Driven pulley 112…… 03-00-0060-0 01….. Bearing 51104 77…….. 26-00-0006-0 01….. Roll pin Ø3x16mm 113…… 8NPO-KK55-0 02….. Jam nut 78…….. 82SB-KK49-0 01….. Lock bushing 114…… 06-09-0020-0 02….. Hex nut M8x1,25 79…….. 82SB-K118-0 01….. Nut ** 115.. 82SB-KK22-0 01….. Tilt Adjustment Rack 80…….. 07-00-0030-0 01….. Spring 116…… 06-04-0097-0 02….. Hex head cap screw M10-1,5x25 81…….. 82SB-KK50-0 01….. Saw shaft lock 117…… 26-03-0011-0 02….. Roll pin Ø8x24 82…….. 8NCV-K257-0 01….. Key 118…… 82SB-KK71-0 01….. Saw trunion bracket 83…….. 06-18-0017-0 01….. Snap ring I62 119…… 06-09-0022-0 01….. Hex nut M12x1,75 84…….. 120…… 27-00-0003-0 01….. Handle 85…….. 8NFL-KK36-0 01….. Outer blade collar 121…… 8NPF-KK23-0 01….. Handle shaft 86…….. 06-05-0059-0 08….. Round head screw M6-1x16 122…… 06-18-0018-0 01….. Snap ring RS8 87…….. 10-03-0019-0 01….. Front panel 123…… 8NAR-KK81-0 01….. Washer Ø25x9x3,1 88…….. 82SB-KK32-0 01….. Tilt scale 124…… 06-03-0061-0 01….. Allen cap screw M8-1,25x30 89…….. 06-17-0003-0 02….. Pop AD 3,2 rivet 125…… 82SB-KK16-0 01….. Hand wheel 90…….. 06-05-0062-0 04….. Round head screw M4-0,7X16 126…… 8NPF-K22-0 01….. Lock screw 91…….. 11-27-0001-0 01….. Green ON Button 127…… 06-05-0043-0 02….. Round head screw M5-0,8X10 92…….. 11-27-0012-0 01….. Red OFF Button 128…… 82SB-KK63-0 01….. Saw tilt indicator 93…….. 82SB-KK96-0 01….. Switch box cover 129…… 82SB-KK17-0 01….. Hand wheel hub 94…….. 82SB-KK94-0 01….. Switch box 130…… 03-00-0060-0 02….. Bearing 51104 ** 95…. 84SB-KK99-0 01….. Tilt adjustment shaft * 131... 82SB-KK69-0 01….. Elevation shaft 96…….. 03-00-0060-0 01….. Bearing 51104 132…… 82SB-KK52-0 01….. Pin 97…….. 82SB-K127-0 01….. Hand wheel 133…… 06-03-0033-0 01….. Allen cap screw M8-1,25x70 98…….. 8NPF-KK25-0 01….. Lock screw 134…… 26-03-0011-0 02….. Roll pin Ø8x24 99…….. 06-03-0061-0 01….. Allen cap screw M8-1,25x30 135…… 06-04-0098-0 02….. Hex head cap screw M10-1,5x35 100…… 8NAR-KK81-0 01….. Flat washer Ø25x9x3,1 136…… 06-04-0088-0 01….. Hex head cap screw M8-1,25x40 101…… 06-18-0018-0 01….. Snap ring RS8 137…… 06-09-0020-0 01….. Hex nut M8-1,25 102…… 8NPF-KK23-0 01….. Handle shaft * 138…. 82SB-KK23-0 01….. Vertical movement bracket 103…… 27-00-0003-0 01….. Handle 139……. 06-02-0081-0 01….. Allen set screw M6-1x30 104…… 82SB-KK81-0 01….. Lower saw base 140……. 06-09-0029-0 01….. Hex nut ½” unc

* 82SB-2077-0 Blade height screw/rack assembly (131 & 138) ** 82SB-2078-0 Blade angle screw/rack assembly (95 & 115)

21

Table Saw Mod. RT-40

FIG. Nº CODE QTY. NAME FIG. Nº CODE QTY. NAME 141…… 82SB-KK67-0 01….. Pin 177…… 82SB-K220-0 01….. Outer spacer 142…… 82SB-KKK7-0 01….. Saw support 178…… 8NCA-KK34-0 01….. Adjustable lock handle 143…… 06-13-0015-0 03….. Flat washer Ø10mm 179…… 82SB-KK42-0 01….. Stud 144…… 82SB-KK25-0 03….. Support plate 180…… 82SB-K212-0 01….. Bushing 145…… 06-04-0069-0 01….. Hex head cap screw M10-1,5x80 181…… 8NMN-KK79-0 01….. Knob 146…… 29-34-0010-0 01….. Motor 7,5 hp 182…… 26-00-0002-0 01….. Roll pin Ø3x24 147…… 06-09-0021-0 04….. Hex nut M10-1,5 183…… 27-00-0011-0 02….. Adjustable lock handle 148…… 06-13-0015-0 04….. Flat washer Ø10mm 184…… 82SB-K227-0 01….. Rip fence scale 149…… 06-04-0089-0 04….. Hex head cap screw M10-1,5x50 185…… 82SB-K213-0 01….. Rip fence guide bar 150…… 82SB-KK97-0 01….. Motor base plate 186…… 06-17-0002-0 01….. Pop 440S rived 151…… 06-30-0103-0 02….. Allen cap screw M12-1,75x45 187…… 8NVR-K101-0 02….. Threaded rod 152…… 06-13-0024-0 02….. Washer 188…… 06-09-0001-0 04….. Hex nut M16-2 153…… 8NAR-KK85-0 01….. Washer Ø30x13x4 189…… 06-13-0006-0 02….. Flat washer Ø5/8” 154…… 06-02-0054-0 01….. Allen set screw M8-1,25x10 190…… 06-13-0015-0 06….. Flat washer Ø10mm 155…… 8NP-K159-0 01….. Motor pulley 191…… 06-04-0098-0 06….. Hex head cap screw M10-1,5x35 156…… 15-00-0020-0 02….. Correia VA-26 series “V” belt 192…… 06-13-0015-0 02….. Flat washer Ø10mm 157…… 82SB-KKK8-0 03….. Spacer 193…… 06-04-0121-0 02….. Hex head cap screw M10-1,5x30 158…… 06-05-0040-0 02….. Round head screw M8-1,25X20 194…… 82SB-K102-0 01….. Rip fence extension bar 159…… 06-13-0025-0 02….. Flat washer Ø8mm 195…… 82SB-KKK5-0 01….. Table extension 160…… 82SB-KK24-0 01….. Chip duct 196…… 06-02-0053-0 04….. Allen set screw M6-1x10 161…… 06-02-0061-0 02….. Allen set screw M10-1,5x16 197…… 82SB-K210-0 01….. Table insert plate 162…… 82SB-KK79-0 01….. Upper chip deflection plate 198…… 82SB-KKK3-0 01….. Cast table 163…… 06-23-0001-0 02….. Screw 199…… 06-02-0054-0 04….. Allen set screw M8-1,25x10 164…… 82SB-KK62-0 01….. Trunion plate 200…… 82SB-KKK4-0 01….. Table extension 165…… 06-04-0088-0 02….. Hex head cap screw M8-1,25x40 201…… 06-03-0068-0 04….. Allen cap screw M10-1,5x50 166…… 82SB-KK18-0 01….. Rip fence cast base 167…… 8NPW-K501-0 01….. Threaded rod (short) 168…… 82SB-KK41-0 01….. Rip fence lock bar 169…… 21-88-0085-0 02….. Aluminum rip fence caps 170…… 82SB-KK30-0 01….. Aluminum rip fence 171…… 8NPW-K502-0 01….. Threaded rod (long) 172…… 82SB-K215-0 01….. Scale pointer 173…… 06-06-0028-0 02….. Flat head screw M4-0,7x10 174…… 82SB-KK43-0 01….. Support pin 175…… 82SB-K218-0 01….. Rip fence block 176…… 82SB-K219-0 01….. Inner spacer

22

Table Saw Mod. RT-40

Parts and Service

InfoWest@invicta-usa.com InfoEast@invicta-usa.com

www.invicta-usa.com