MANTEL - pdf.lowes.com
Transcript of MANTEL - pdf.lowes.com
MANTEL MODEL
X6022-1TEKX6022-1MAHX6022-1BLKX6022-1GRY
X6022-1CHRX6022-1WHTX6022-1WAL
1 REV19-01
3
PACKAGE CONTENTS
Carefully remove all pieces from the carton and make sure that you have all parts listed (refer to parts list on page 2-3).
A Top Panel 1B Left Side Panel 1C Right Side Panel 1D Top Shelf Divider 1E Shelf Rail 1F1
Right Trim Panel 1
F2
Left Trim Panel 1
G1
Right Inner Panel 1
G2
Left Inner Panel 1
H Base 1I Base Back Panel 1J Base Left Panel 1K Base Right Panel 1L
Base
Left
Support1
MBase Right Support
1N Base Middle Support 1O Top Shelf 1P Upper Back Panel 1Q1 Lower Back Panel 1Q2 Lower Back Panel 1R1 Adjustable Shelf
f1
R2 Adjustable Shel 1S Base Middle Panel 1T Left Door 1U Right Door 1
AA Bolt 61BB Metal Connector 61CC Shelf Pin 8DD SPanel crew 24EE Cabinet Door Hinge 4FF Handle 2GG Screw M4X18 2SS 1Safety Chain
4
PACKAGE STEPS
1.
2.
AA
M
N
L
M N L
X6
J
SK
5
PACKAGE STEPS
3.
4.
AA X2
AA
I
M
N
BB
L
X6
I
6
PACKAGE STEPS
5.
6.
BB
X16AA
7
PACKAGE STEPS
7.
8.
H
BB X16
AA X8
8
PACKAGE STEPS
9.
10.
9
PACKAGE STEPS
11.
12.
G2
AA X3 X3AA
G1
G1 GF1 F2
2
10
PACKAGE STEPS
13.
14.
BB X3
CC X4
BB X3
G1
G1
G2
G2
11
PACKAGE STEPS
15.
16.
BB X4
Q1Q2
AA X7
12
PACKAGE STEPS
17.
18.
O
BB X3
E
13
PACKAGE STEPS
19.
20.
O
BB X2BB X2
14
PACKAGE STEPS
21.
22.
X2
B
B
C
C
CC
X2AA X2AA
X2CC
15
PACKAGE STEPS
23.
24.D
X4BB
X4BB
X2BBX2AA
AA X6
A
P
16
PACKAGE STEPS
25.
26.
ABB X6
17
PACKAGE STEPS
27.
28.
R1
R2
18
PACKAGE STEPS
29.
30.
T
EE X2
FF
GG
DD X4
U
EE X2
FF
GG
DD X4
X8DD
19
PACKAGE STEPS
31.
32.
X8DD
T
U
20
PACKAGE STEPS
IMPORTANT - Safety Chain Installation
WARNING:
INSTALLATION:
This mantel is heavy furniture. Please be sure to correctly attach the safety chain to both the mantel and an adjacent wall. Failure to do so can cause serious injury or death.
Assemble the mantel and place it in positionAttach one end of the chain to a wall stud using the screw includedAttach the other screw – through a link in the chain – to the center of the mantel’s top board (you may need to drill a small starter hole). Put the screw through the chain link that allows the least amount of slack in the chain.Carefully test that the installed chain adequately prevents tipping or tilting of the mantel.
NOTE: The chain must be as short as possible to prevent the mantel tipping forward. Do not allow slack in the chain.