Manhole covers Gully gratings and Surface Boxesakartabet.com/pdf/Municipal Castings.pdf ·...
Transcript of Manhole covers Gully gratings and Surface Boxesakartabet.com/pdf/Municipal Castings.pdf ·...
Municipal castingsDuctile iron
Manhole coversGully gratings
and Surface Boxes
General contents
Key benefits 4/5Selection criteria for manhole covers 6/7Manhole covers - contents 8Installation guide for manhole covers and gratings 28/29Telecom covers and sealed covers 30/32Tree grates 33Gully gratings - contents 34Selection criteria for gratings 35/36Surface Boxes 54/55
Pages
2
t the interface between thecar r iageway and sewersystems, municipal castingsmust satisfy the multiple perfor-mance and quality criteria ofsewer system managers withregard to :• resistance to traffic stresses :
safety, stability, silence.• easy access and operation of
sewer systems : simple,q u i c k and e r gonom i chandling, maximum flowcapacity of surface waterand filtering of debris, ifrequired.
• s i m p l e e m b e d m e n t :reliable installation in all siteconditions.
Combining performance andinnovation as well as qualityand durability, the SAINT-GOBAIN CANALISATIONranges of manhole covers andduct covers, gratings and gullyunits all benefit from thespecific mechanical propertiesof ductile iron and the designknowledge of the marketleader in municipal castings inEUROPE.
A
SAINT-GOBAIN CANALISATION
3
4
Key benefits
For more than 40 years, the SAINT-GOBAIN CANALI-SATION Municipal Casting ranges have been drawingbenefit from the unmatched qualities of ductile iron :impact strength, resistance to specific mechanicalstresses, high breaking strength and very high safetyfactors.
Thanks to the knowledge built up over many years indesign and castings techniques, SAINT-GOBAINCANALISATION’s latest generations of gratings andmanhole covers have been designed with new perfor-mances.
The elasticity of ductile iron allows the linking and loc-king of AUTOLINEA and SQUADRA gratings and theSELECTA gully unit as well as the automatic locking ofthe new REXEL carriageway manhole cover, without theuse of accessories.
In ductile iron, the graphite particles, which looklike small spheres, provide high tensile strength
eliminating any risk of cracking.
REXEL : the spring bar, integrated in the cover, allows automatic locking of the REXEL cover without accessories.
The spring-lock device guarantees:• Stable seating in the frame• Complete silence when trafficked• Secure locking
DUCTILE IRON
5
Quality
ELASTOMERSManufacturer of sewer mains renow-ned for tight sealing, SAINT-GOBAINCANALISATION has built up outs-tanding mastery in the field of elasto-mer materials. For some 20 years,SAINT-GOBAIN CANALISATIONhas chosen to apply this skill to munici-pal castings where the quality of therings used and their specific shapesensure perfect stability of covers, safetyfor traffic and complete silence.
And for many years, as the elastomerrings are tested by the passing ofseveral million vehicles.
SERVICE
Through Head Offices, its salesnetwork in France and everywherethroughout the world, SAINT-GOBAINCANALISATION and engineeringteams are responsive to customerrequirements and offer advice andtraining.
Quick deliveries are ensured byefficient logistics based on a stock of200,000 items.
A close-knit network of stockists anddistributors ensures that all ranges areavailable on all European markets andpromotes the SAINT-GOBAINCANALISATION image of quality andservice.
What you need to know about the EN 124 standard,certification, and quality...
2 : Manufacturer identification4 : Resistance class
5 : Reference standard6 : Mark of approval of the certification third-party body
Additional markings:1 : Ductile iron quality marking 3 : Product identification
In compliance with EN 124, all products bearing the mark for municipal castings mustalso bear the following markings:
The following information is supplied in compliance with Article 10 of the French Decree dated 30 March1995 concerning the certification of industrial products:• The mark for municipal castings certifies that compliance with Regulation NF-110 and themanufacturer's specifications via continuous inspection procedures carried out by AFNOR.• The following table lists the main certified specifications. For all figures, please refer to the relevant paragra-
ph EN 124 or to the regulations.Caractéristiques § de EN 124 B125 C250 D400 E600 F900Ventilation area 7,2 • • • • •Clear opening 7,3 • • • • •Depth of insertion 7,4 • • • •Cover/frame securing 7,8 • • • •Frame bearing area 7,15 • • • •Frame depth 7,16 • • • •Opening angle 7,17 • • • • •Waterway area 7,9 • • • • •Test load 8,3,2 • • • • •Material Mark rules • • • • •Trap seal depth Mark rules •Road trials Mark rules • • •Access for disabled people Mark rules •Gratings & Gully gratings slip resistance Mark rules • •Study of design files of hinges, locking devices & gaskets
• Euronorm EN 124 * : is a standard approved by CEN in Brussels relating to municipal castings, which has beenadopted in all European countries. Under this, compulsory certification must be carried out by a third-party body. Itslogo is mandatory cast on both cover/grate and frame.
• The Quality mark * : for municipal castings was introduced by AFNOR (French standards authority). Products bearing the stamp meet the specifications of EN 124, as well as additional quality criteria. Thecredibility of this approval is backed by the renown and expertise of the inspection and verification testing housesacting on behalf of AFNOR.
13
24
5
6
*Extract form AFNOR 1999 brochure.
The mark for municipal Castings guarantees a complete Quality AssuranceManagement covering all stages of production,
The mark for municipal Castings guarantees that strict product safety and performan-ce have been carried out,
The mark for municipal Castings guarantees product tracability and origin,
The mark for municipal Castings guarantees customer service,
The mark for municipal Castings guarantees clear and precise information.
• AFNOR-Certification - 11, avenue Francis de Pressensé - 93571 Saint-Denis la Plaine Cedex
6
Selection criteria for manhole covers
PLACES OF INSTALLATION
Standard EN 124 divides products into minimum level groups and classes according to their intended place ofinstallation :
TRAFFIC STRESSES
The following three parameters :- number of vehicles,- speed,- type of vehicles - cars or heavy vehicles using the carriageway,are combined and contribute to the definition of the concept of the type of traffic.
Some manhole covers are capable of passing a test load which exceeds that specified for their class. Othersare fitted with a reinforced frame in order to ensure stability in especially severe traffic conditions, while remai-ning in compliance with the installation conditions considered in the standard.
In addition to the group and class concepts specified in EN 124, it is recommen-ded that specific traffic and operating stresses should also be taken into accountin order to select the most suitable product.
TYPE OF TRAFFIC NUMBER OF VEHICLES SPEED TYPE OF VEHICLES
Intense High Speed authorizedon large urban roads
Regular use byheavy vehicles
Low Low Limited speed Occasional truck traffic(deliveries, etc.)
Normal Irregular Stabilized urban speed - Essentially light vehicles- Transit of heavy vehicles
TYPE OF TRAFFIC STABILITY / BEARING INSERTION DEPTH (I)
Intense Weight of cover Elastomer ring I 80 mm
Normal - Locking- Metal seating PE ring Locking or I 50 mm
FRAME DEPTH (F)
F = 100 mm
F = 100 mm or F = 75 mmwith anchoring means
SAINT-GOBAIN CANALISATION designs its manhole covers in accordance with traffic stresses in terms of : stability,safety and silence. The type of technical solutions implemented depends on the intended use of the casting.
SECURING OF COVER /GRATING IN FRAME
NOTE : Standard EN 124 specifies that, where there is any doubt on the class to be used, the higher classmust be selected.
• Group 6 : (class F 900) : Areas imposing particularly high wheel loads, such as aircraft pavements, etc..
• Group 5 : (class E 600 mini) : Areas imposing high wheel loads, such as docks, port areas, aircraft pavements,airports, factory yards, etc..
• Group 4 : (class D 400 mini) : Carriageways of roads - including pedestrian streets, hard shoulders and parkingareas for all types of road vehicles.
• Group 3 : (class C 250 mini) : For gully tops installed in the area of kerbside channels of roads which, whenmeasured from the kerb edge, extend to a maximum of 0.50 m into the carria-geway and a maximum of 0.20 m into the footway.
• Group 2 : (class B 125 mini) : Footways, pedestrian areas and comparable areas, car parks and car parkingdecks.
7
Selection criteria for manhole covers
Efficient management of sewer systems requires more frequent inspections and checks. The handling ofmunicipal castings designed without due care can lead to damage in the lumbar region of the back and spine.All SAINT-GOBAIN CANALISATION manhole covers are designed to facilitate opening and closing operationswith a minimum of force and to provide service teams with more ergonomic working conditions.
OPERATING STRESSES
INSPECTIONS OPENING ASSISTANCESYSTEM USER SAFETY OPENING ERGONOMICS
Frequent Hinge 90° locking Opening to 130°
1 single movementStanding position
Occasional None Cover positioningmarker
Bending of back andpulling / lifting effort
Periodic - Hinged mechanism- Pins
Device ensuring holdingof tool and guidance
of coverHandling in two steps
SAINT-GOBAIN CANALISATION offers a very wide range of carriageway manhole covers in accordance with allthe requirements of standards and satisfying the specific criteria of each place of installation.
RANGE
CLASS F 900
CLASS E 600
CLASS C 250
CLASS B 125
Intense traffic
Normal traffic
Low traffic
Car parksKerbsides
Pedestrian streets
Pavements andpedestrian streets
Specific areas(airport, docks,
plants yards, etc...)
Infrequent inspections Periodic inspections Frequent inspections
CLASS D 400
URBAMAX 900
URBAMAX 600
AKSESS and PAVEMENT RANGES
PAYSAGE and PARXESS RANGES
Operatering stresses
Traf
ficstr
esse
s
RC 40
REXELGTS
PAMREXKORUM
8
Manhole covers - contents
URBAMAX 9PAMREX 10PAMREX 700, PAMREX 800 11/13PAMTIGHT - Double-triangular manhole covers 14KORUM 15REXEL 16/17GTS - RC 40 18Various manhole covers 19Manhole covers for pavement and car parks - PARXESS 20/21AKSESS covers 22/24Pavement covers 25
Pages
9
URBAMAX
HIGH STRENGTH
Ductile ironClass E 600 / F 900Elastomer ringPush-in central padSealed handling boxEN 124
Intense traffic
Designed to withstand all types of traffic, URBAMAX can be installed onroads subjected to super heavy duty loading in addition to airports anddock areas, etc..
STRENGTH ++++URBAMAX, class E 600 andF 900, has a high tensilestrength.
STABILITY +++The weight of the cover (63 kgin the non-ventilated version)and the addition of an elasto-mer ring and a double skirtdampens vibrations caused bytraffic, ensuring total stability.
OPERATION ++A handling box allowsURBAMAX to be handled withtraditional site tools : such as apointed or flat end pick-axe, orcrowbar. The cover is speciallydesigned to ease closing.
URBAMAX E 600 URBAMAX F 900
Frame ReferenceTotal Cover Clear opening Frame depth
round CFUR60AF 9363
600 100square CFUR60KF 105
round CFUR60BF 8861,5
square
Type
Non-ventilated
VentilatedCFUR60LF 97
round CEUR60AF 9362
600 100square CEUR60KF 102
round CEUR60BF 8660,5
square
Non-ventilated
VentilatedCEUR60LF 95
Mass (kg) Dimensions (mm)
Clas
s F
900
Clas
s E
600
10
PAMREX
Ductile ironClass D400 for heavy traffichingedElastomer ringSealed handling boxOptional anti-theft cover lockLifting rings integral with the frame
Intense traffic
� NEW HANDLING BOXRaising the PAMREX cover to make a visual ins-pection while standing is effortless: place a crow-bar at 35° in the brand new handling box inser-tion point and nothing could be easier.Conventional means of opening are also possible.
STRENGTH ++++PAMREX has a high safety factor witha breaking strength margin wellabove the requirements of EN 124.
Designed to withstand the stresses ofintense traffic, in terms of largenumbers of vehicles, regular use byvery heavy vehicles and high speeds,PAMREX is the absolute reference interms of performance and durabilityin France and Europe.
STABILITY ++++PAMREX is silent : there is no metal-to-metal contact. Its frame is fitted withan elastomer ring which ensures :
� damping of mechanical stressescaused by the repeated passage ofvehicles,� self-centering and stability of thecover : the ring pinches the lower skirtand works against the suction pheno-menon caused by vehicles’ tyres.
OPERATION ++++The PAMREX hinge ensures easy openingand operating safety :� The PAMREX hinge does not come intocontact with the frame when the cover isclosed and it is, therefore, not subjected totraffic stresses. It is only placed understress during opening and closing opera-tions,� in the event of the sewer system beingaccidentally pressurized, the PAMREXcover opens without coming out of itshousing and recloses under its ownweight.
HIGH RESISTANCE TO TRAFFIC, ENHANCED ERGONOMIC DESIGNDesigned to cope with the heaviest traffic but quiet thanks to its elastomer seal, PAMREX is a reliable manholethat has withstood the test of time.PAMREX’s new enhanced ergonomics now make it even easier to carry out works on systems while alsoimproving operator safety.In hundreds of towns and cities, even after millions of vehicles have driven over it, PAMREX continues todemonstrate its qualities of endurance and reliability.
ERGONOMICS ++++
The “extrasthat makelife easier”
Safety / Operationidentification
Option of fitting ananti-theft system
New surface design
Anti-fouling design
Lifting eyes
Identification of frameshape from markings,visible after embedment Lifting eyes
11
PAMREX
PAMREX WITH APPARENTFRAMEFrame designed for easycobbles and paving installation, (height= 160 mm)� for paved and pedestrian
streets
THE PAMREX RANGE
• The PAMREX grating is interchangeable with any cover of PAMREX 600 series• The PAMREX grating is interchangeable with the cover. (see page 37)• Special versions of PAMREX fitted with a water-tightness plug are also available. Please consult.PAMREX accessories, see page 14.
Easy installation A manhole cover designed to match perfectly into its environment.
Opens to 130°, blocks at 90°when closing� for sewage pipeworks� cover appearance matches
paved surrounding areas� operation conditions identical
to any other PAMREX versions
PAMREX SAFETY WITHCONCRETE INFILLEDCOVER Type of frame Reference
Total Cover O H
Round
Square
CDPA60GL
CDPA60WF
108
117
75
75
610
610
100
100
Type
Non-ventilated
Non-ventilated
Mass (in kg) Dimensions mm
Type of frame ReferenceTotal Cover O H
apparent
apparent
CDPA603F
CDPA604F
132
131
55
54
610
610
160
160
Type
Non-ventilated
Safety
ventilated
Mass (in kg) Dimensions mm
Opens to 130°, blocks at 90°when closing� for sewage pipeworks
PAMREX SAFETY
Opens to 130°, without bloc-king at 90° when closing� for pipeworks inspection from
road surface
PAMREX OPERATION
Type of frame ReferenceTotal Cover O H
Round
Square
CDPA60EF
CDPA60MF
88
97
55
55
610
610
100
100
Type
Non-ventilated
Non-ventilated
Round
Square
CDPA60FF
CDPA60PF
87
96
54
54
610
610
100
100
ventilated
ventilated
Mass (in kg) Dimensions mm
Type of frame ReferenceTotal Cover O H
Round
Square
CDPA60AF
CDPA60KF
88
97
55
55
610
610
100
100
Type
Non-ventilated
Non-ventilated
Round
Square
CDPA60BF
CDPA60LF
87
96
54
54
610
610
100
100
ventilated
ventilated
Mass (in kg) Dimensions mm
12
Wide clear-opening manhole covers
PAMREX 700 Safety Ductile ironClass D400 heavy trafficHingedClear opening: 700 mmElastomer ringSealed handling boxOptional anti-theft cover lockLifting rings integral with frameEN 124
Intense traffic
PAMREX 800 Safety
PAMREX 700 has the same functional features as PAMREX 600 (see pages 10 and 11). Access is made through awide 700-mm opening specifically designed for systems requiring special safety conditions for operators.
Ductile ironClass D 400 heavy trafficClear opening : 800 mmOpens to 130°, blocks at 90° when closingElastomer ringSealed handling boxOptional anti-theft cover lockLifting rings integral with frameEN 124
� Pamrex 800 provides easy opening,while continuing to offer the high perfor-mance levels of the successful Pamrex600 mm and 700 mm clear openingdesigns.
� The 800 mm clear opening enablesmaintenance personnel to enter themanhole with their safety equipment,or to lower bulky equipment into thebelow ground network.
PAMREX accessories, see page 14.
Intense traffic
NEW
Type of frame ReferenceCover O H
Round
Square
CDPA80EFX37
CDPA80MFX37
121
131
73
73
800
800
125
125
Type
Non-ventilated
Non-ventilated
Round
Square
CDPA80FFX37
CDPA80PFX37
121
131
73
73
800
800
125
125
ventilated
ventilated
Dimensions mm
Total
Mass (in kg)
PAMREX 800 Safety with opening assisted - closing with SCS locking kit (key not-provided)
This version has the same features as the PAMREX 800 standard version. The liftingeffort and the stresses transmitted to the chamber are reduced with its assistance stainless steel gas arm. This product is systematically fitted with a SCS locking system.
EN 124
Type of frame ReferenceTotal Cover Clear opening Frame depth
Round
Square
CDPA70EF
CDPA70MF
108
118
71
71
700
700
100
100
Type
Non-ventilated
Non-ventilated
Round
Square
CDPA70FF
CDPA70PF
108
118
71
71
700
700
100
100
Ventilated
Ventilated
Mass (in kg) Dimensions mm
Type of frame ReferenceTotal Cover O H
Round
Square
CDPA80EF
CDPA80MF
121
131
73
73
800
800
125
125
Type
Non-ventilated
Non-ventilated
Round
Square
CDPA80FF
CDPA80PF
121
131
72
72
800
800
125
125
ventilated
ventilated
Mass (in kg) Dimensions mm
13
VIATOP NIVEAU
VIATOP NIVEAU Ductile iron manhole coverAdjustableIntense trafficClass D400, EN 124Height adjustableClear opening 610 mm
Intense traffic
Type of frame ReferenceTotal Cover D
Round
Round
CDVT60QGX40
CDVT60RGX40
83
84
49
51
610
610
AD
815
815
H
140
140
Type
Ventilated
Non-ventilated
Mass (in kg) Dimensions mm
• Designed forventilated coversand grating
• 4 suspensionlegs rest on elastomer ring
• High resistance to load of sandand mud
• Mudpans do not impair manholecovers or gratings normal functioning
References
C1
Model
GALVANISED STEEL MUDPAN FOR PAMREX
STEEL MUDPAN FOR COVER AND GRATING PAMREX 600
References
C4
Model
STEEL MUDPAN FOR VIATOP NIVEAU
STEEL MUDPAN FOR COVER AND GRATING VIATOP NIVEAU
C2
STEEL MUDPAN FOR PAMREX 700
C3
STEEL MUDPAN FOR PAMREX 800
VIATOP NIVEAU 140
Type of frame ReferenceTotal Cover D
Round
Round
Round
Round
CDVT60RG
CDVT60QG
CDVT60TG
CDVT60SG
98
99
122
123
49
51
72
73
610
x
x
610
610
610
AD
815
815
815
815
H
200
200
200
200
Type
Ventilated
Ventilated
Non-ventilated
Non-ventilated
Mass (in kg) Dimensions mm ConcreteInfilledCover
VIATOP NIVEAU 200
• Cover always perfectly lined up with the surface of the carriageway after compacting.
• An adaptation concrete ring is supplied with each Viatop Niveau.• No load applied directly on the concrete chamber.• 90° Blocking.• Elastomer noise damper ring.
14
PAMTIGHT
Square opening manhole cover
Ductile ironClass D 400Two rings : - polyethylene seating ring
- elastomer sealing ringFastened by 6 bolts and clamping clawsSealed handling boxEN 124
PAMTIGHT is sealed to prevent the ingress or escape of water to a 1 barpositive or negative pressure rating.
STRENGTH +++By design, PAMTIGHT com-bines resistance to trafficstresses and tight sealing.STABILITY +++The cover is fastened by sixclamping claws held by stain-less steel bolts. Provisionshould also be made foranchoring the frame to thecover of the shaft in addition toensuring the bedding is sea-led.OPERATION +The clamping device can berotated and the cover openedsimply by loosening the bolts.Easy handling is facilitated bythe relative low cover weight(52.5 kg) and the presence ofa handling box (sealed).
Frame ReferenceTotal Cover Clear opening Frame depth
Round CDPE60AF 102 52,5 610 100
Type
Non-ventilated
Mass (in kg) Dimensions mm
HIGH-PERFORMANCE SEALING
Ductile ironClass D 4002 triangular half coversWidened-angles frameSquare clear opening :600 x 600 mmMetal seatingEN 124
Normal trafficDOUBLE TRIANGULAR MANHOLE COVERS
Non-rock 3-point suspension on each cover.
Frame ReferenceTotal Cover Clear opening Frame depth
Square CDIA60KF 77,9 2 x 30 600 x 600 100
Type
Non ventilated
Mass (in kg) Dimensions mm
Normal traffic
Important The kit Trafex (Reference : C49) was developed to improve the exploitation of the manhole cover Pamtight in conditions ofextreme service : under strong and violent vibrations from traffic or as result of handling operation and maintenance carriedout without the necessary precautions. It consists of anti-rotation clips, clamps, screws and washers as well as detailednotices. Its installation is the responsability of the usual sanitation teams’ services or road ones, according to the commentsthey have made on the site. In case of doubt as to its use, contact the Regional Directorate of Saint-Gobain Pam. Themanhole cover Pamtight is now offered for sale equipped with the kit Trafex.
15
KORUM
STRENGTH : ++++New frame and ribs design prevent the deformation of the KORUM under intense traffic conditions
STABILITY : ++++The spring locking mechanism underconstant tension locks the KORUM coverin place in its frame in complete safety.
OPERATION : ++++The hinge blocks at 90° when closing andensures operating safety..
Ductile ironClass D400HingedComposite ringSealed handling boxSpring barOptional anti-theft spline / Optional anti-intrusion lock
ERGONOMICS ++++Safe and effortless handling thanks to the ball-joint hinge.Effortless unlocking and opening of cover with pickaxe point
LocktypeD50
ReferenceTotal Cover O H
no CDKO60EF 62 38 606 104
Mass (in kg) Dimensions mmSpline
no
Type offrame
round
Type
Non ventilated
no CDKO60MF 69 38 606 104nosquareNon ventilated
no CDKO60FF 62 38 606 104noroundventilated
no CDKO60PF 69 38 606 104nosquareventilated
no CDKO60EFX17 62 38 606 104yesroundNon ventilated
no CDKO60MFX17 69 38 606 104yessquareNon ventilated
no CDKO60FFX17 62 38 606 104yesroundventilated
no CDKO60PFX17 69 38 606 104yessquareventilated
yes CDKO60EFX15* 62 38 606 104noroundNon ventilated
yes CDKO60MFX15* 69 38 606 104nosquareNon ventilated
yes CDKO60FFX15* 62 38 606 104noroundventilated
yes CDKO60PFX15* 69 38 606 104nosquareventilated
yes CDKO60EFX31* 62 38 606 104yesroundNon ventilated
yes CDKO60MFX31* 69 38 606 104yessquareNon ventilated
yes CDKO60FFX31* 62 38 606 104yesroundventilated
yes CDKO60PFX31* 69 38 606 104yessquareventilated
Ductile iron anti-theft spline Prevent the coverfrom being extractedand stolen. It can beinstalled after thebedding of theframe.
Note: accessoriesare painted yellowfor illustration purpose
Anti-intrusionlock :The new locks D50,Penta+ and SCS+features a ductile castiron bar, with highresistance tovandalism attempts.
* for the locked version, please ordered the locking key (ref: C46) separatly
Intense traffic
KIT D50 FOR KORUMReference
C47
C46
ModelKit without handling key
Handling key
KIT PENTA+ FOR KORUMReference
C54
C17
ModelKit without handling key
Handling key
KIT SCS+ FOR KORUMReference
C101
C18
ModelKit without handling key
Handling key
Penta and SCS kits (with steel bar) available page 17
16
REXEL
Ductile ironClass D 400Automatic locking by ductile iron spring bar (patented system)Optional anti-theft cover lockHingeUnlocking boxEN 124
A
E
F
G
B C D
Photo A : opening to 130°, cover with seven-sided pot andreminder of site safety instructions.
Photo B : quick, simple releasing without requiringaccessories.
Photo C : press-down central key way for lifting withcrowbar, optional plastic plug available.
Photo D : reliable locking in all circumstances.
Photo E : spring locking bar integrated in cover.
Photo F : the spring locking bar is compressed under thecover plate.
Photo G : easy opening hinge, green sound-proofing ringfor stability and silence.
CAPTIONS :
Frame
Spring bar integral withcover
17
REXEL
KIT “PENTA” FOR REXEL KIT “SCS” FOR REXEL
Reference
C9
C17
Model
Kit without handling key
Handling key
Reference
C11
C18
Model
Kit without handling key
Handling key
Normal traffic
Representing a new generation of carriageways manhole covers, REXELcombines the innovation of its spring locking mechanism requiring noaccessories with easy opening, stability, safety and silence.
STRENGTH +++The completely new design ofREXEL gives a double guarantee ofperformance and long service life.Optimized geometry of the cover :rigidity and strength to withstandthe stress of usual carriageway’straffic.Fully mastered frame profiles : per-fect seating on shafts, effective anddurable bedding.
STABILITY +++The spring locking mechanism provides REXEL with remarkabledynamic stability :3 contact points : the hinge, the locking mechanism and the ringensure vertical stability of the coverin the frame.Permanent contact between the loc-king mechanism and the cover positioning lugs ensure horizontalstability.The locking mechanism keeps thecover held against the sound-proo-fing ring : the cover is preventedfrom rocking and complete silenceis ensured.
OPERATION +++• Easy opening : using suggestedtools, a lever effect in the handling boxfrees the spring locking mechanismand releases the manhole cover.• Easy lifting once unlocked : thehinge reduces the force required toopen the cover by half. For completelyergonomic handling, the central padin the cover can be pushed in, andreclosed using the special plug(optional).• Easy locking when closing : thecover can be locked without requiringany accessories, by simply pressingwith the foot. If it is left unlocked, REXELis locked automatically as soon as thefirst vehicle crosses it.
THE BEST OF EXPERIENCE
THE REXEL RANGE
ROUND FRAMEReferences
Total Cover Clear opening Frame depth
Non-ventilated CDRX60AF 57 32
31600 100
Ventilated CDRX60BF 56
Mass (in kg) Dimensions mm
SQUARE FRAMEReferences
Total Cover Clear opening Frame depth
Non-ventilated CDRX60KF 65 32
31600 100
Ventilated CDRX60LF 64
Mass (in kg) Dimensions mm
Blanking plastic plug, for push-in central pad : C19
18
GTS
RC 40
Ductile iron + concreteClass D 400Supplied with concrete infillPolyethylene ringSealed handling boxEN 124
Low traffic
Lightweight concrete infilled manhole cover suitablefor areas with low traffic density.
Ductile ironClass D 400Locking by 3 lugs and 1 keyPolyethylene ringEN 124
Normal traffic
STRENGTH ++With a breaking safety factor,GTS is intended for use on roadswith normal traffic loadings.
STABILITY ++GTS is equipped with an originalcover locking system : rotation ofthe cover, cast iron key and poly-ethylene seating ring.
OPERATION ++Handling efforts are reducedthanks to the light-weight cover.
GTS RANGE
Mass (in kg)
Type
Non-ventilated
Ventilated
Round
Square
Round
Square
CDGT60AF
CDGT60KF
CDGT60BF
CDGT60LF
Frame Reference Total
64
72
63
71
34
600 100
33
Cover
GTS MANHOLE COVER
Frame depth
GTS ACCESSORIES
Type Depth Reference
1 - levelling insert50 mm C20
C21
C22
C17
60 mm
-
-
2 - security lock
3 - handling key
Dimensions mm
1
23
Frame ReferenceTotal Cover Clear opening Frame depth
Round
Square
CDRC60CF
CDRC40KF
78
84,559,5 600 75
Type
Non-ventilated
Mass (in kg) Dimensions mm
NB: The frames are supplied with grouting holes in compliance with EN124 functional requirements.
Clear opening
19
Accessories for all PAMREX manholes and gratings ranges
INSPECTION MANHOLE STEPSDUCTILE IRON
-1- -2- -3- -4- -5-
Reference
C25C26C27C28C29
Dimensıons mm Mass
in kgd C B A2
2,42,52,55,3
25252525
153300300300
365200200200
I60606060
1533503503501200
Type
1/ BS1247 galvanized2/ Standard3/ with handbar cross4/ with handbar holder5/ handbar
*Complies with EN 124 functional requirements
• 1/4 turn lock actuated by an asymetrical five-sided bolthead.
• On site installation takes 5 minutes :� Punch out the centre of the locking bolt position.� Install the kit in compliance with the instructions supplied
• Lock must be operated with the handling key supplied withthe kit or separately.
References
C14
Model
Kit without handling key
C17Handling key
References
C6
Model
Kit without handling key
C17Handling key
LOCKING KITS "PENTA"
KITS PENTA FOR COVER AND GRATINGPAMREX 600 AND COVER PAMREX 700
KITS PENTA FOR PAMREX 800
References
C16
Model
Kit without handling key
C18Handling key
References
C8
Model
Kit without handling key
C18Handling key
KITS SCS FOR COVER AND GRATINGPAMREX 600 AND COVER PAMREX 700
KITS SCS FOR PAMREX 800
• 1/4- turn lock is activated by a bolt which has a unique notched cylindrical headdesign, this feature improves security by ensuring that the SCS locking key can onlybe removed once the manhole cover has been returned to the locked position.
• SCS key with an internal trigger-operated lug that releases the key from the headof the bolt.� The key can only be released once the manhole cover is locked, thus
making it impossible to forget to lock the cover.• On site installation takes 5 minutes :
� Punch out the centre of the locking bolt area.� Install the kit in compliance with the instructions supplied.
• Requires use of the SCS key included in the complete kit� It is recommended the SCS key not be used to open the covers. Covers should
only be opened using standard tools and the lifting points provided.
"SCS" LOCKING KITS NEW
20
Cover for traffic-bearing pedestrian zone
PARXESS
Ductile ironClass C 250 Polyethylene ringSealed handling boxEN 124
The PAYSAGE C 250 manhole cover canbe installed in parking areas, at roadsides,in kerbside channels or on pedestrianfootways.
The new PARXESS hydraulic range is designed to provide an innovative, reliable andefficient response to new needs for access covers located in pavements and similarlocations, where they may have to withstand the occasional load of passing vehicles.PARXESS offers the same benefits as AKSESS. (See p 22 and 23)
PAYSAGE
Identification of underground networks: four different caps are provided, each markedwith a symbol representing an underground network, are available as an option.- Plate of 4 identification caps: C42- Locking kit without operating key: C41- Locking kit with operating key: C40- Operating key: C17
ReferenceTotal Cover Clear opening Frame depth
CBPK40HF
CBPK50HF
CBPK60HF
CBPK70HF
23,4
32
39
54
15,6
21,5
31
45,4
300
400
500
600
56
Mass (in kg) Dimensions mm
ERGONOMICS Convenient, easy opening andhandling of cover
STABILTY New cover seatings system with improveddynamic cover location within the frame
STRENGTH Frames and covers are designed toprovide rigidity, resistance to deflectionand durability
EASY Wide flanged frames give optimal INSTALLATION seating and efficient, durable bedding
on square concrete boxes
Frame ReferenceTotal Cover Clear opening Frame depth
Round
Square
CCPY60RF
CCPY60CF
53
6035 600 75
Type
Non-ventilated
Mass (in kg) Dimensions mm
NEW
21
Manhole covers for parking areas
HEIGHT ADJUSTABLE INSPECTION COVERS
Ductile ironClass C 250EN 124
These manhole covers are fitted on DN 400, DN 300 and DN 250extensions installed on DN 300 and DN 250 inspection chambers. Thehinged cover is tamper-proof once sealed. The cover, sliding insideelastomer ring, is height adjustable up to 95 mm. Tightness is obtainedby means of a sealing ring (supplied) for either:
• cast iron DN 300/DN 250• PVC DN 300/DN 250• PVC DN 400
SQUARE FRAME
Cover Reference Total Cover Clearopening Adjustability
Mass in kg Dimension mm
FrameFrame
dimension
Round CCBR40BF 30,6 10 303 80450 Square
Shape
MaterialSize
PVC400
Round
CCBR30AF
20 6 225 95360 Square
castIron
300
CCBR30BFPVC
Round
CCBR25AF
16 4 181 95318 Square
castIron
250
CCBR25BFPVC
Box
ROUND FRAME
Cover Reference Total Cover Clearopening Adjustability
Mass in kg Dimension mm
FrameFrame
dimension
Round CCBR40SFX27 26,3 8,7 303 80460 Round
Shape
MaterialSize
PVC400
Round
CCBR30SFX26
19,5 6 225 95380 Round
castIron
300
CCBR30SFX27PVC
Round
CCBR25SFX26
15 4,3 181 95330 Round
castIron
250
CCBR25SFX27PVC
Box
22
AKSESS : pavement hydraulic manhole cover
STABLE, QUIET AND STRONGThanks to their perfect stability, AKSESS (water) manhole covers ensure quiet, trouble-free use for pedestrians andresidents alike.• 3-point non-rock system ensures the cover remains firmly seated in its frame• Rigid and stable frames incorporating the LTS® system• The underside of the wide seating pads located at each corner of the frame have a unique corrugated design that
improves embedment and increases resistance to lateral shear by upto 5 times more than conventional designs
APPEARANCEAKSESS is a range of attractive and functional manhole covers for pavementapplications featuring:• A new dynamic non-skid surface pattern,• A universal lifting point with integral usage indicator• A specific diagram for the locked versions
� Ductile ironHydraulic manhole coverB 125 classNew black varnish coatingEN 124
AKSESS, FOLLOW THE STAR OF MANHOLE COVERS
LOCKED AKSESS COVERS
SECURITY AND THEFT DETERRENCEThe locked version of Aksess covers meets specific requirements for theprevention of theft, vandalism and intrusion• Protection of appliances and equipment installed under pavements• Deterrent against cover theft • Locked AKSESS covers have a special opening that can only be operatedusing the AKSESS key, which operates the special 1/4-turn lockGuaranteed protection of your equipment.
EASY OPERATION AKSESS, the fast and ergonomic solution for access to networks ins-talled under pavements• Opens effortlessly and remains stable in the vertical position in its frame;• Slides effortlessly for practical handling;• The lifting point for non-locked AKSESS covers is ergonomic and
designed for use with standard tools
standard Aksess
23
AKSESS : pavement hydraulic manhole cover
OPTIONAL NETWORK IDENTIFICATION
Specific AKSESS caps:• Protect the locking system against the ingress of debris• Identify the type of network installed under the pavement
The AKSESS caps symbolise four of the most common services forwhich manholes are used:• Wastewater• Storm water• Water meters• Lighting/Traffic lights
Each locked Aksess manhole cover is supplied with four identification caps.
ReferenceOutside of frame Clear opening Frame height
CBAK30HFX16
CBAK40HFX16
CBAK45HFX16
CBAK50HFX16
310 x 310 220 37 8,2
12,8
15,3
18,2
Type
AKSESS 300
410 x 410 300 37AKSESS 400
460 x 460 350 38AKSESS 450
510 x 510 400 38AKSESS 500
Dimensions mmMass kg
LOCKED VERSION
ReferenceOutside of frame Clear opening Frame height
CBAK30HF
CBAK40HF
CBAK45HF
CBAK50HF
CBAK60HF
CBAK70HF
CBAK80HF
310 x 310 220 37 8,2
12,8
15,3
18,2
29,4
38,8
52,7
Type
AKSESS 300
410 x 410 300 37AKSESS 400
460 x 460 350 38AKSESS 450
510 x 510 400 38AKSESS 500
610 x 610 500 38AKSESS 600
720 x 720 600 38AKSESS 700
820 x 820 700 41AKSESS 800
Dimensions mmMass kg
STANDARD VERSION (NON LOCKED)
CBAK60HFX16
CBAK70HFX16
CBAK80HFX16
29,4
38,8
52,7
610 x 610 500 38AKSESS 600
720 x 720 600 38AKSESS 700
820 x 820 700 41AKSESS 800
ReferenceType
C17Aksess handling key
Locking with “SCS” solution : please consult
CBAK55HF
CBAK75HF
22,0
32,0
550 x 580 450 38AKSESS 550
560 x 710 450 x 600 38AKSESS 550 x 700
CBAK55HFX16
CBAK75HFX16
22,0
32,0
550 x 580 450 38AKSESS 550
560 x 710 450 x 600 38AKSESS 550 x 700
24
Other B125 Manhole covers
SQUARE HYDRAULICMANHOLE COVERS
CIRCULAR HYDRAULICMANHOLE COVERS
CBHY25HF
CBHY30HF
CBHY40HF
CBHY50HF
CBHY60HF
CBHY70HF
CBHY80HF
Frame Cover
Shape
Reference Total Cover Clear opening Frame depth
Square Square
6,3
8,1
3,4
5
188
233
29
29
Dimensionsof frame
250
300
12,9 8,3 329 30415
26,5 15,5 404 48520
37,3 23 500 48,5600
50,3 33 601 48,5700
69 48 700 50830
Mass (in kg) Dimensions mm
CBHY40SF
CBHY50SF
Frame Cover
Shape
Reference Total Cover Clear opening Frame depth
Round Round11,6
20,9
7,3
12
340
407
30
48
Dimensionsof frame
437
CBHY36SF 9,4 5,6 250 30360
537
CBHY70SF 40 27,4 600 60700
Mass (in kg) Dimensions mm
Other B125 Manhole covers
25
PAVEMENT MANHOLECOVERS WITH SQUARE FRAME
PAVEMENT MANHOLECOVERS WITH CIRCULAR FRAME
MEDIUMCLASS B125
Based on the same design principle as the PAYSAGE, the MEDIUM manholecover is the ideal solution for areas subjected to occasional, light traffic. Its poly-ethylene ring ensures stability and prevents rocking.
NB: references available in C250 class page 20, “PAYSAGE”
Ductile ironPolyethylene ring EN 124
Frame Cover
Shape
Reference
CBTB25RF
CBTB30RF
CBTB40RF
CBTB50CF
CBTB60RF
CBTB70RF
CBTB80CF
Total Cover Clear opening Frame depth
Square Round
4,1
5,7
1,1
1,8
150
175
17
17
Dimensionsof frame
250
300
10 3,8 250 18400
18,5 6,7 350 30500
25,5 9,5 425 30600
36,4 13,4 500 35700
54,5 26 610 35800
Mass (in kg) Dimensions mm
CBTB50RF
CBTB80RF
Frame Cover
Shape
Reference Total Cover Clear opening Frame depth
Round Round13,2
38,5
6,7
26
350
610
30
35
Dimensionsof frame
500
800
Mass (in kg) Dimensions mm
Frame Reference Total Cover Clear opening Frame depth
Round
Square
CBTC60RFX24
CBTC60CFX24
50
5730 600 75Non-ventilated
Mass (in kg) Dimensions mm
26
Technical characteristics of manhole covers
D 400
PAMREX “600” 10 610 INTENSE ��� � � � �Circular andsquare 850/840
PAMREX “700” 12 700 INTENSE ��� � � � �Circular andsquare 900/950
PAMREX apparent frame 11 610 INTENSE ��� � � � �square 850
REXEL 16 600 NORMAL � � � �Circular andsquare 850/850
GTS 18 600 NORMAL � � �Circular andsquare 850/850
RC 40 18 600 LOW � � �Circular andsquare 850/815
PAMTIGHT 15 600 NORMAL �� � � �Circular 850
DOUBLE-TRIANGULAR 15 600x600 NORMAL � � � �square 800x800
DÉCOR 19 400/610 NORMAL � � � �Circular 840/640
C 250
PAYSAGE 20 600 - � � � �Circular andsquare 850/850
PARXESS 20 300 to 600 - ��� � � � �square 450 to 730
MANHOLE COVERS FORINSPECTION CHAMBERS 21 225/180 - � � � �Circular and
square 360/318
PAMREX “800” 12 800 INTENSE ��� � � � �Circular andsquare 1000/1000
VIATOP NIVEAU 13 930 INTENSE ��� � � � �Circular 1135/1138
KORUM 15 606 INTENSE �� � � � �Circular andsquare 841
Strengthclass
F 900
Type ofmanhole cover
URBAMAX 900
Pages
9
FRAME COVER
Clear openingmm
600
STRENGTH
Type of traffic
INTENSE
strengthmargin
���
Strengthfactor
� � � �
Shape
Circular andsquare
Dimensionsmm
850
E 600 URBAMAX 600 9 600 INTENSE ��� � � � �Circular andsquare 850
B 125 MEDIUM 25 600 - ��� � � Circular andsquare 850/815x815
AKSESS 22 220 to 700 - ��� � �square 310 to 820
Various pavement covers 25 -
27
SAINT-GOBAIN PAM
100 Elastomer ring Ball-joint � � � � 85 � � � �
100 Elastomer ring Ball-joint � � � � 85 � � � �
160 Elastomer ring Ball-joint � � � � 85 � � � �
100 PE ring Spring barhinge � � � Locked � � �
100 PE ring � � Locked � �
75 PE ring � � 55 �
100 Elastomerand PE ring � Bolted � � �
100 Metal/metal � � Fastened � � �
130 Neoprene ring � 80 � � �
75 PE ring � � � Not applicable(EN 124) � � �
56 Non-rock system � � � �Not applicable(EN 124) � � � �
180/154 Metal/metal For chambersø 300 and 250 � � � � Not applicable
(EN 124) � � �
STRENGTH, STABILITY ANDOPERATING FACTORS=Multiple-criteria comparison betweenproducts within the same class only(Class D 400, for example).
BREAKING STRENGTH MARGIN=Comparison between average brea-king strength of the product and theEN 124 requirement.
� = Average breaking strength up to20% higher than EN 124 require-ment.
�� = Average breaking strength upto between 20% and 30% higherthan EN 124 requirement.
��� = Average breaking strengthmore than 30% higher than EN 124requirement.
NOTE- Strength margins are specified withregard to the classes of utilization towhich the respective products corres-pond.
- The field of application of products islimited to their utilization class by design.
125 Elastomer ring � � �76 � � � �
150 Elastomer ring Hinge � � � �72 � � � �
96 Composite ring Ball-joint � � � �63 � � � �
STABILITY
Frame depthmm
100
Frame/coverseating
Elastomer ring
OPERATING-FACTORS
Specialdevice
Operatingfactor
� �
Depth ofinsertion mm
85
Stabilityfactor
� � � �
100 Elastomer ring � �85 � � � �
75 PE ring � � Not applicable (EN 124) � � �
37 à 41 Non-rock system Two openingmodes � � � �Not applicable
(EN 124) � �� �
28
Requirements for installation of manhole covers and gratings with frame
EXPERTISE AT THE SERVICE OF DESIGN
EXPERTISE AT THE SERVICE OF RELIABILITY
All the frames for SAINT-GOBAIN CANALISATION municipal castingsare designed to ensure easy and reliable implementation and toguarantee long service life :• complete compatibility with standardized concrete shafts,• surrounding slots to ensure effective bedding,• frame depth (generally 100 mm) allowing the application of
bedding mortar and the road surface coating level with the frame,• optimization of resistance to traffic loading.
D 40EN 124
NF P 29
0- 31-8
NF
F e r m éO u v e r t
NF
D400
EN
124N
FP2
9 -31
8
The following advice on fitting is taken from the sewerage reference catalogue.
1 - REMOVING A MANHOLE COVER OR GRATING ON AN EXISTING SEWER MAIN
• Make a cavity, staying asclose as possible to the bed-ding flange of themanhole cover.
• Remove debris.• Extract the cover from the
frame.• Carefully extract the frame.• Avoid debris falling into the
manhole.
* Additional precautions • Inspect and check for a sound seating surface.• Allow for a seating layer at least 30 millimetres
thick under the bedding flange frame.• Never reinstall the frame sole directly on the top
of the manhole or on the rim.• Prick the seating surface to ensure adhesiveness
of mortar.• Remove the dust and hose the cavity.
2 - FITTING THE FRAME
Trying to level a frame before applying theasphalt layer is a difficult and unreliableoperation. The frame must therefore belevelled after applying the asphalt layer.
The resistance of the manhole cover and ofthe bedding depend on this phase. Thetechnique using cross-beams (or battens) isthe most commonly used :
• It allows the frame to be levelled regardless of the slopeor camber.
• It avoids the settling of the manhole cover when the beddingmaterial sets (subsidence of the frame under its own weightbefore setting).
* Operating procedure :• Secure the frame onto two
crossbeams or battens with wire.• Place this assembly across the cavity.• Centre the assembly vertically with
respect to the manhole.• Leave a space of approximately 3
cm between the frame and the top ofthe manhole.
3 - PROTECTING THE SHAFTBefore placing the bedding material :
• Protect the manhole against any accidental introduction of mortar into the network.The formworks allow the filling of mortar under the bedding flange.
Inner tube form
There are two methods
Wooden form
29
Requirements for installation of manhole covers and gratings with frame
5 - DIAGRAM OF TYPE OF BEDDING
• Steady the frame by packing with bedding mortar until it emerges through the slotsin the bedding flange.
• Continue bedding in order to lock the frame in place.• 30 to 40 kg of cement type CPA 55 + sand/frame.• Do not fill the cavity completely.• Leave approximately 3 cm for surfacing.• Protect the wet bedding with damp sacks and/or a curing agent applied as soon
as the mixture starts to set.• Avoid excessive drying which results in cracking of the bedding.
7 - CLEANING AND FINISHING
3 cm = surfacing bituminous finish
2 to 3 cm = bedding material
Carriageway and formation level
Shaft
NBWhen mixing the bedding mortar, please respect the recommended doses, and the water-to-cement ratio. Carefully follow the manufacturer's recommendations (instructions onpackaging). The setting time must be complied with before reopening to traffic. Thesetting time will vary according to the ambient temperature and relative humidity.
• Remove the form (planks or inner tube).• Check that the bedding material has not
penetrated between the frame and thecover.
* Additional precautions• Manhole tops equipped with ring :
Check that the ring seating has not been spoiled by any upward flow ofbedding material.
• Secured manhole tops : Clean ramps or seatings to ensure proper fittingof the cover.
• PAMREX : Provide for clearance under the hinge box housing in order tofacilitate cleaning. (See the self-adhesive label on the product).
Note :Cover the manhole cover with sand or kraft paperbefore applying the surfacing.This protection for the cover (against surfacingcoated materials or emulsion) ensures thatoperation of the closing device remainsunhampered.
4 - PLACING THE BEDDING MORTAR
6 - CHARACTERISTICS BEFORE REOPENING TO TRAFFIC
Dirt
Minimum resistance
Material
Low traffic
10 daN/cm2
Cement mortar
Intense traffic
50 daN/cm2
Resinous mortarAluminous mortar
30
Duct cover ranges
The TELECOM DUCT COVERS ranges developed by SAINT GOBAIN PAM offersolutions able to cover most kinds of networks. They are designed in compliancewith main worldwide operators specifications. 6 complementary ranges:• “IRON HINGED COVERS ON IRON FRAMES“ range • “FRANCE TELECOM“ range: Iron covers on steel frames • “BRITISH TELECOM“ range: Iron covers on iron frames• “CABLE and TV“ range: Iron or steel covers on iron frames • “SLIDING DUCT COVER“ range: Sliding iron covers on iron frames• “SEALED DUCT COVER“ range: Iron covers and frames machined and lubricated.
If a specific product development is required SAINT GOBAIN CANALISATION is perfectly well equipped todesign technical solutions that provide a creative response to the problem.
Please consult us for technical sheet or a meeting with a specialist.
HINGED TRIANGULAR COVERS ON IRON FRAMES
TELECOM DUCT COVERS
A
B
Clear opening(mm) Reference Nbr
CoversCovers Frame Total
600 x 630 DDTT66BX 2 31x2 37 99
100
700 x 800 DDTT87BX 2 46x2 41 131
750 x 750 DDTT75GX 2 44x2 38 126
750 x 1200 DDTT12GX 4 35x4 68 208
750 x 1500 DDTT17GX 4 44x4 75 251
750 x 2250 DDTT27JX 6 44x6 94 358
Mass (kg)H ( mm)
� EN 124D400
� Covers security features (option)
Locking system: quarter turn (Ref. C6)
Master cover Slave cover
31
Wide clear opening modular duct covers
PERFORMANCEThe frame rigidity and the flatness of thechamber rim guarantee the duct cover’sdurability.When handling the duct cover unitbefore and during installation, it isadvisable to hold the cover in its frame.
Description :
� The covers are made of ductileiron.
� The frames are of hot-galvanized,welded steel.
CHAMBER
Type Clear opening(mm) Layout
FRAME
Overhall(mm) h (mm) Mass
(kg)
ASSEMBLY
Reference Mass(kg) Pack.
COVERS
Nbr Mass(kg)
Overall dimensions of frame (excluding bedding lugs).
ACCESSORIESReference
D10
D11
Type
France Telecom approved hammer
Standard hammer
L1T 520 x 380 1 36 650 x 510 60 12 DCL153AF 48 5L2T 1160 x 380 2 72 1280 x 510 60 19 DCL213BF 91 5L3T 1380 x 520 3 108 1500 x 650 60 23 DCL315CF 131 5L4T 1870 x 520 4 144 2010 x 650 60 28 DCL415GF 172 5
1/2L4T 850 x 520 2 72 980 x 650 60 19 DC1L85BF 91 5633 x 495 1 36 633 x 495 - - DCL146W - 10
P2T 1160 x 880 2 160 1280 x 1010 60 24 DCP218BF 184 5L5T 1790 x 880 3 240 1920 x 1010 60 32 DCL518CF 272 5L6T 2430 x 880 4 320 2850 x 1010 60 39 DCL628GF 359 3M2T 3060 x 880 5 400 3180 x 1010 60 46 DCM238HF 446 3
990 x 633 1 80 990 x 633 - - DCP269W - 10
C 250
L0T 430 x 250 1 16 510 x 330 60 9 DBL042AF 25 5495 x 316 1 16 495 x 316 - - DBL042W - 10
L1T 520 x 380 1 30 650 x 910 60 12 DBL153AF 42 1L2T 1160 x 380 2 60 1280 x 510 60 19 DBL213BF 79 5L3T 1380 x 520 3 90 1500 x 650 60 23 DBL315CF 113 5L4T 1870 x 520 4 120 2010 x 650 60 28 DBL415GF 148 5
1/2L4T 850 x 520 2 60 980 x 650 60 19 DB1L85BF 79 5633 x 495 1 30 633 x 495 - - DBL146W - 10
P2T 1160 x 880 2 134 1280 x 1010 60 24 DBP218BF 158 5L5T 1790 x 880 3 201 1920 x 1010 60 32 DBL518CF 233 5L6T 2430 x 880 4 268 2550 x 1010 60 39 DBL628GF 307 3M2T 3060 x 880 5 335 3180 x 1010 60 46 DBM238HF 381 3
990 x 633 1 67 990 x 633 - - DB6269W - 10
Other network applications: possible identification by means of a specific logo at the center of cover. Consult us for advice.
Cover : ductile iron, bituminous paint coating. • Frame : steel profile, 120 mm deep, welded and galvanized.
B 125Cover : ductile iron, bituminous paint coating. • Frame : steel angles, 60 x 60 x 6 mm, welded and galvanized. Except LOT = frame : steel corner 60 x 40 x 5 mm.
K1C 750 x 750 2 130 910 x 911 80 41 DDK175BF 171 4K2C 1500 x 750 4 260 1660 x 911 80 57 DDK217GF 317 4K3C 2250 x 750 6 390 2410 x 911 80 75 DDK327JF 465 4L1C 527x389 2 27x2 650 x 510 72 34 DDLD53BX 88 5L2C 1161x389 4 27x4 1280 x 510 72 51 DDLD13GX 159 5L3C 1381x527 6 27x6 1900 x 650 72 67 DDLD15JX 223 5
D 400Cover : ductile iron, bituminous paint coating. • Frame : steel profiles, “L” et “T”, 80 mm, deep-welded and galvanized.
Cover (without frame)
Cover (without frame)
Cover (without frame)
Cover (without frame)
Cover (without frame)
Accessories required for installation (Sold separately)
32
PAMETIC2
DUCT COVERS PAMETIC2
D17 Standard keys Set of 2 standard handling keys + a hexagonal key + a spanner
D18 Set of long handle keys Set of 2 long handle manual lifting keys + a hexagonal key + a spanner
D19 Graphite grease
D20 Set of mechanical keys 4 keys per kit
D21 Plastic plugs Sold per 100 pieces
Please contact us Small clamps Please consult us
AACCESSORIES
Complementary accessories
Specific areas like: airports, bridges, industrial sites, laboratories, … require a high level of sealing on duct coversfor pit and specific chambers
KEY BENEFITS
Stability
Resistance
Sealing
Rigidity
Easy installation •
Security •
Modular system •
Whereever sealing, security and reliability are required is the answer. Ask for the specific catalogue
Reference Designation Detail
D20 D17
D18 D19
3 main fields of application:- Sealed duct covers with 1 to 3 covers on a row- Sealed access covers for technical channels - Sealed multispan duct coversPerformances :• The bearing surface between frames and covers is comple-
tely machined : the precision of the components and the
absence of gap provide sealing, stability and completesilence
• Water and odours tight sealing assisted with specialsealing grease
• Easy and safety opening with handling keys• For multispan duct covers possibility of opening the
selected cover
33
Tree grates
6 - CÉZANNEGrate
Frame
EACE10
E0SE10C
30
4
4
21000 500 17 47
7 - GAUGUINGrate
Frame
EAGA10
E0GA10C
34
5,6
4
41000 500 17 54
“READY-ASSEMBLED” GRATES
1 - DESLANDESGrate
2 - MONETGrate
3 - FANTIN-LATOURGrate
4 - DAUBIGNYGrate
5 - SEURATGrate
6 - GrateCÉZANNE
7 - GrateGAUGUIN
Combining aesthetic appeal and strength,SAINT-GOBAIN CANALISATION tree gratesprotect trees from vandalism and damage byvehicles.The various patterns are designed to fit inwith all styles while providing a largeenough area for the absorption of waterand to allow trees to develop.The grates can be fitted on a galvanizedsteel angle fitting/frame.The opening of Monet, Fantin-Latour andDaubigny grates can be increased to 975mm by cutting the central ring in order to pro-mote tree growth.
1 - DESLANDESGrate
Frame
EADE20
EODE20C
152
6,4
4
42000 600 27 45
2 - MONET*Grate
Frame
EAM014
E0M014C
60
5,4
4
21414 600 17 45
3 - FANTIN-LATOUR*Grate
Frame
EAFL14
E0FL14C
92
8
4
41414 600 17 48
4 - DAUBIGNYGrate
Frame
EADA18
E0DA18C
102
6,8
4
41800 600 17 52
5 - SEURATGrate
Frame
EASE10
E0SE10C
52
4
2
21000 500 20 32
8 - ETNAGrate
Frame
EAET12
E0ET12C
48
4,4
4
41200 460 20 -
9 - SANTORINGrate
Frame
EASA14
E0SA14C
60
5,6
4
41450 740 20 -
10 - KILIMANDJAROGrate
Frame
EAKI17
E0KI17C
72
6,4
4
41720 1000 20 -
Type ReferenceUnitmasskg
Nbrparts
For information
DimensionsVentilated area
%External
mmInternal
mmThickness
mm
(*) Grates can be combined together.
HIGH PROTECTION GRATES
8 - ETNAGrate
9 - SANTORINGrate
10 - KILIMANDJAROGrate
Ductile iron
Nota : References comprises all necessary elements for grate or frame assemblyNota 2 : For spare elements ordering, please contact
34
Gully grates - contents
he collection of run-off water has become a majorconcern : � the development of impermeable surfaces consi-
derably increases the volumes to be drained,� while, at the same time, sewer system operating
constraints are changing user needs, especiallywith regard to the filtering of debris and accessfor maintenance operations.
On the strength of its recognized experience insewerage and its know-how as the leading Europeanmanufacturer of municipal castings, SAINT-GOBAINCANALISATION offers a range of drain gratings thatprovide users with efficient, reliable and durablesolutions. Always attentive to customer needs, SAINT-GOBAIN CANALISATION is constantly seeking toimprove its product ranges to satisfy futurerequirements.
T
PAMREX gratings 37REXEL, PAYSAGE gratings 38DEDRA 39SQUADRA gratings 40/41Square frame gratings 42/43Kerbside gratings 44/45SELECTA gully units 46/47Gully units, Communal Grating 48/49AUTOLINEA channel gratings 50/51Channel gratings 52/53
Pages
35
Selection criteria for gully grates
In order to help customers make their choice among the various gully units, frame gra-tings and channel gratings in the gully grates range, SAINT-GOBAIN CANALISATIONhas prepared a dimensioning and decision-making aid software package.It can be used to determine the following points on the basis of the characteristics ofthe site studied :� the type of grates,� the number of grates to be used,� the spacing between two successive castings,� the quantity of rainwater drained by the sewer system.
Please consult our sales engineering teams.
TYPE OF COLLECTIONRun-off water can be collected either :
� by gully grates in a road carriageway or in a parking area, or by kerbside gully units.� Linear collection, by channel gratings.
LOCATION OF GULLY POTThe type of grating to be used is generally determined by the location of gully pots and the design of thedrainage network.
� When the gully pot is situated directly under the carriageway, a square flat grating is used.� When the gully pot is positioned to provide kerb and carriageway drainage, either a gully grate
or a SELECTA inlet should be used.� When gully pots are sited under the foot-path, units which incorporate a cover plate and grate are
used.
TRAFFIC RESISTANCE
DECISION-MAKING AID
Like manhole covers, gully grates must be selected according to their place of installation as this determinestheir strength class in accordance with the definition in EN 124 (see page 6).
Multi-directional collection Chanelled drainage
Gully pot positioned undercarriageway
Kerb or carriageway combination Gully pot positioned underpavement
Selection criteria for gully grates
36
CLASSD 400
CLASSC 250
CLASSE 600
RANGEConfronted to the wide diversity of situations encountered, users are increasingly choosingspecific drain inlet devices in order to optimize the collection of rainwater and run-off water.
In response to this demand, SAINT-GOBAIN CANALISATION provides a wide range of productsconstituting suitable technical solutions for each specific configuration.
AUTOLINEAgratings
MECALINEAgratings
Reinforced stability
Standard
Reinforced stability
VBS gulliesSOLE LAZIO ITALIA gratings
SELECTA gully units
SELECTAkerb gratings
SQUADRA Flatsquare gratings
SQUADRA concavesquare gratings
Gully gratings
AT and rectangularflat gratings
Simple gullies andcover plates
Standard
PAYSAGEcircular gratings
Flatsquare gratings
concavesquare gratings
Types of drainage
Traf
fic r
esis
tanc
e
MULTI-DIRECTIONALCollection
KERBSIDECollection
CHANNELLEDDrainage
With spring bar locking
TRANSLINEAgratings
PAMREXcircular gratings
DEDRAgratings
REXELcircular gratings
TRANSLINEAgratings
AUTOLINEAgratings
* for channel application: use gratings with side bars and 2 end plates
Ductile IronMachined and greased seatingfaces2 levelling bolts on each side bar(level setting)
GRATING GATIC FOR AIRPORTS F900 Clear openingReference
850 X 300
EFGR83ZX
EFCL30JX
E14
96
85
5,5
850 X 450
EFGR84ZX 122
EFCL45JX 108
E15 7
850 X 750
700 X 750
Outside framedimension
mm
900 x 570 x 140
850 x 570 x 140
900 x 720 x 140
850 x 720 x 140
900 x 870 x 140
850 x 870 x 140
750 x 1020 x 140
700 x 1020 x 140
Grate with frame
Grate on 2 side bars
End plate*
Grate with frame
Grate on 2 side bars
End plate*
Grate with frame
Grate on 2 side bars
End plate*
Grate with frame
Grate on 2 side bars
End plate*
EFGR86ZX
EFCL60JX
E16
EFGR77ZX
EFCL75JX
E17
227
210
8,5
248
228
10
Mass kg
Frame ReferenceTotal Grating Clear opening Frame depth
Round
Round
EDPA60AF
EDPA60BF
91
9158 610 100
Type
SafetySquare EDPA60 100
OperationSquare EDPA60DF 100
10,75
Mass kg Dimensions mm Waterway areadm2
37
PAMREX gratings
Ductile ironClass D 400 hingedElastomer ring1 handling boxLifting rings integral with the frameOptional anti-theft grate lockingInterchangeable with PAMREX coverEN 124
Completely interchangeable with PAMREX covers, thegrating version withstands the most intense traffic. Silentthanks to its elastomer ring, the PAMREX grating is inno-vative owing to its hinge mechanism which facilitatesopening and allows locking safety. It can be used onan ad hoc basis during sewer inspections or on a per-manent basis to ventilate systems and reduce the risksof hydrogen sulphide formation.
PAMREX GRATING
PAMREX safety : cover opening to 130°, 90° locking on closing.
PAMREX accessories, see page 14
38
Circular gratings
LOCKING KITSSee page 17
Ductile ironClass D 400Automatic locking by ductile iron spring bar(patented system)HingeUnlocking boxOptional anti-theft grate lockingRexel grate is interchangeable with coverEN 124
The REXEL grating is specially designed to withstandmedium-density traffic. Its design ensures perfor-mance, long-life and stability.
REXEL GRATING
Frame ReferenceTotal Grating Clear opening Frame depth
Circular EDRX60BF 57 32 600 100
Square EDRX60DF 65
11,9
32 600 100 11,9
Mass kg Dimensions mm Waterway areadm2
Ductile ironClass C 250Polyethylene ringInterchangeable with PAYSAGE coverEN 124
The PAYSAGE grating is installed on shafts sited intraffic-free locations.The concave shape of the concentric bars optimizesmulti-directional collection.
PAYSAGE GRATING
Frame ReferenceTotal Grating Clear opening Frame depth
Circular ECPY60BF 5536 600 75
Square ECPY60DF 6213,5
Mass kg Dimensions mm Waterway areadm2
39
DEDRA
A new range of gratings designed for all types of traffic stresses, carriageways, parking, kerbside…,thanks to its high performances stability features.Details of the DEDRA product: • Flat square gratings with 4 side-flange frames (street setting) and 3 side-flange frames (kerb setting) • Concave gratings with 4 side-flange frames Two types of frames available:• With standard opening• With round opening
- forming a mud-pan (ref: E4 not supplied) bearing plate and centring studs for pipes and 400 NDplastic extensions
FLAT AND CONCAVE* HINGED GRATINGS DEDRA 400
DEDRA GRATINGS D400
DEDRA 400 flat 4 side-flange frame DEDRA 400 concave 4 side-flange frame
Type of frameGratingshape
Total Grating Frame
Mass kgReference
Clear opening HeightSides Suitable for Mudpan
Waterway area dm2
no
yesflat
51,1
56,8
52,4
58,1
52,3
60
28,7600x550
EDDE40RFX143 Sides
400 102
11,3
28,7 EDDE35RFX14350 102
no 28,7
600x600
EDDE40DFX14
4 Sides
400 102
yes 28,7 EDDE35DFX14350 102
noconcave
28 EDDE40DFX15400 127
yes 28 EDDE35DFX15350 127
Dimensions mm
FLAT HINGED GRATINGS DEDRA 600
Type of frameGratingshape
Total Grating Frame
Mass kgReference
Clear opening HeightSides Suitable for Mudpan
Waterway area dm2
no flat88,2
85
50,6 800X800
800X714
EDDE60DFX144 Sides
3 Sides 600 100 18,7
50,6 EDDE60RFX14
Dimensions mm
*restriction of use according to EN 124 standard
DEDRA 600 4 side-flange frameFrame 3 side-flangeFrame 4 side-flange
DEDRA 400 concave 4 side-flange opened
EN 124
40
Square gratings with frames and automatic locking
SAFETY ++++� Flat SQUADRA gratings can be rotated 90°: the click-in system operates whatever the position of the grating in its frame.This feature means the bars can be placed perpendicular to the flow of traffic, irrespective of the way in which the frame hasbeen sealed into place.
� Concave SQUADRA gratings also provide maximum safety with bi-directional bars ensuring safety forcyclists and pedestrians.
The "T"-frame ensures optimum seating of the grating, andbetter assembly fit on the concrete gully pot.
INSTALLATION AND OPERATION ++++
� flat soled frame for practical and effective embedment
� compatible with prefabricated concrete manholes
� easy to open by system service teams using a crowbar orpickaxe as lever
� easy to close automatically : place the grating into its frame,exert pressure on the grating with foot or tool to lock it safely»
GRATING
FRAME
SPRING BAR
SQUADRA FLAT AND CONCAVE C250Ductile ironClass C 250Secured by patented ductile ironspring-lock mechanismEN 124
Successfully developed with AUTOLINEA gratingsand the REXEL manhole cover, the ductile iron springlocking mechanism equips SQUADRA gratings.Locking of the gratings and a newly designedframe provide maximum stability and more preciseinstallation on the gully pot.
STABILITY ++++SQUADRA gratings incorporate a feature considered by users to be increasingly important: stability.
Flat SQUADRA
concave SQUADRA
for paved areas and pavements, can be fitted with mudpan
41
SQUADRA gratings with frame and automatic locking
ABSORPTION ++++� The bars have been specially developed to optimizeabsorption.In particular, the presence of a range of directional facetsfacilitates the washing away of leaves, and also breaks upthe water sheet.� Flat SQUADRA: rotate the grating in the frame tooptimize absorption.� Concave SQUADRA: dual bar orientation for maximumperformance.
FLAT SQUADRA
ECSQ50LF 35,5 510 350 10019 9,8
E4 7,0 385 325 600
ReferenceTotal Frame Clear opening Depth
ECSQ40PFX11
ECSQ50LFX11
12,2
37,5
410
510
300
400
39
100
Grating
12,25
21
3,9
7,8
ECSQ50PFX11 28,5 510 400 3921 7,8
ECSQ60PFX11 29 620 500 3929 12,8
Mass kg Dimensions mm Waterway areadm2
SQUADRA 500 FLAT GRATING WITH HIGH FRAME
MUDPAN FOR SQUADRA 500 FLAT GRATING WITH HIGH FRAME
- French decree N° 2006-1658 relating to the technical dispositions for accessibility of municipalcastings and public areas.- french order of january 15th, 2007 relating to the application of the decree above.
SQUADRA 500 FLAT GRATING ACCESS FOR DISABLED PEOPLE
ReferenceTotal Frame Clear opening Depth
ECSQ35PF
ECSQ40PF
15,3
20,1
350
410
250
300
39
39
Grating
10
13,6
2,7
5,2
ECSQ50PF 26,5 510 400 3919 9,8
ECSQ60PF 42 620 500 3925,7 15,1
ECSQ70PF 60 720 600 3947 20,6
ECSQ80PF 77 820 700 3963 28,5
Mass kg Dimensions mm Waterway areadm2
SQUADRA CONCAVE WITH FLAT FRAME
HhOA
ReferenceTotal Frame Clear opening Depth
ECSQ40CF
ECSQ50CF
22,7
30,4
410
510
300
400
58/40
63/40
Grating
14,5
19,5
5
9,8
ECSQ60CF 44,8 620 500 68/4031,5 14,8
ECSQ70CF 63,7 720 600 73/4048 20,7
ECSQ80CF 86,6 820 700 78/4065,5 27,4
Mass kg Dimensions mm Waterway areadm2
42
Square gratings for kerbsides and car parks
Ductile ironClass C 250 Surrounding bedding flangeEN 124
Lazio grating
Italia grating
The ITALIA, LAZIO and MILANO gratings have a raisedframe and a surrounding flange which reinforce thestrength of their bedding and provide greater safetyunder traffic load. The absence of ribs on the outerface of the frame facilitates the installation of thegratings on paved roads or areas.
FLAT GRATING : ITALIA
Milano grating
ReferenceBase sizemm
Total Frame Clear opening Depth
ECIT36PF400 x 400 27,3 500 360 80
Grating
13,7 7,7
Mass kg Dimensions mm Waterway areadm2
CONCAVE GRATING : LAZIO
ReferenceBase sizemm
Total Frame Clear opening Depth
ECLZ57CF500 x 500 38,5 570 450 70
Grating
23,5 11,8
Mass kg Dimensions mm Waterway areadm2
FLAT GRATING : MILANO
ReferenceBase sizemm
Total Frame Clear opening Depth
CCMI58CF500 x 500 33,9 580 x 580 440 45
Grating
22 11,8
Mass kg Dimensions mm Waterway areadm2
GRATINGS WITH HIGH FRAME - C 250
43
Square gratings for kerbsides and car parks
SQUARE GRATING WITH FRAME - C 250
Flat square grating
Square concave grating
Ductile ironClass C 250Bedding lugsEN 124
Flat and concave square gratings provide asimple solution for the top of gully pots locatedin traffic-free areas.
FLAT GRATINGS
Base sizemm Reference
Total Frame Clearopening
Depth
200 x 200
250 x 250
ECGP20PF
ECGP25PF
6,8
9,6
218
269
165
215
27
27
Grating
3,8
5,8
1,7
2,4
300 x 300 ECGP30PF 13,0 319 255 278,0 4,2
400 x 400 ECGP40PF 21,3 462 x 422 351 2717,7 7,7
500 x 500 ECGP56PF 32,7 563 x 523 450 2720,8 11,8
600 x 600 ECGP60PF 48 664 x 624 549 2736 16,8
700 x 700 ECGP70PF 77 765 x 725 647 2761 20,2
800 x 800 ECGP80PF 94,5 867 x 827 744 2974 27,6
Mass kg Dimensions mmWaterway area
dm2
CONCAVE GRATINGS WITH CONCAVE FRAMES
Base sizemm Reference
Total Frame Clearopening
Depth
400 x 400
500 x 500
ECGC40CF
ECGC50CF
21,8
31,1
462 x 422
563 x 523
351
450
40
40
Grating
14
21
7,7
11,8
600 x 600 ECGP60CF 49,4 664 x 624 549 4037 16,8
700 x 700 ECGP70CF 75,5 765 x 725 647 42,559 20,2
800 x 800 ECGP80CF 96,5 867 x 827 744 42,575 27,6
Mass kg Dimensions mmWaterway area
dm2
44
Rectangular gratings for kerbsides
GRATING AT - FLAT GRATING WITH FRAME- C 250Ductile ironClass C 250EN 124
Flat rectangular gratings with frames are usually instal-led at the kerbside, alone or in addition to a cover plateor a gully.
Grating AT
Flat grating
SOLE GRATING
Ductile ironClass C 250, 400 kN test loadHingeing on lengthwiseHandling boxAnti-theft gratingReinforced frameEN 124
Easy to open, the SOLE grating is designedto allow quick access to sewer systems. Its raised frame is fitted with a three sides beddingflange, allowing solid and durable beddingat the kerbside, opposite a gully forexample.The grating is anti-theft once it has beenbedded.
Base sizemm Reference
Total Frame Clear opening Depth
878 x 518 ECPS16EK 89 1011 x 598 810 x 450 77/65
Grating
64 36,5
Mass kg Dimensions mm Waterway areadm2
PAMELLAS GRATING
Ductile ironClass C 250EN 124
Reinforced frame with flanges on 3-sides 110° openingWithout blocking at 90° on closure
Concave articulatedgrating locked with anelastic spring bar.Specially designed forareas requiringoccasional high waterabsorption.
ReferenceTotal Frame Clear opening Depth
ECCL30DF
ECML30ZF
40
41
776 x 345
776 x 345
746 x 241
746 x 241
41
41
8,7
7,5
Mass kg Dimensions mm Waterway areadm2
750 x 300
750 x 300
Base sizemm
25
20
Grating
AT
Plate
Type
Base sizemm Reference
Total Frame Clear opening Depth
600 x 350 ECSO63EF 37,5 725 x 420 600 x 350 77
Grating
22 9
Mass kg Dimensions mm Waterway areadm2
SELECTA KERB GRATING, ACCESS FOR DISABLED PEOPLE
Rectangular kerb gratings
45
h
HT
H
O
The SELECTA grating with T-profile raisedselector bars is compatible with:- T-profile cover plate, ref.: ECRV80TF,- T-profile gully, ref.: ECAV80TF
SELECTA grating installed alone.
� Reinforced frame for complete stability and effective seating on concrete structures.
Version withflat grating
SELECTA KERB GRATINGSDuctile ironClass C 250Articulated gratingLocking feature due to spring-lock deviceEN 124
Overalldimensions
mmReferences
Opening O Depth H/h
Flat grating version
800 x 340 ECSE80PFX11 35 660 X 205 90/68 6,1
Overall HT
800 x 340
Mass kgDimensions mm Waterway
areadm2
Version with raised selector bar, T profile
Road-side hinged
SELECTA kerb gratings are fully compatible with standard kerb dimensions as defined in French standard NF P 98-302. They are easy to install and are impeccably finished.
- French decree N° 2006-1658 relating to the technical dispositions for accessibility of municipal castings andpublic areas.- french order of january 15th, 2007 relating to the application of the decree above.
Overalldimensions
mmReferences
Opening O Depth H/h
Flat grating version
800 x 340 ECSE80PF 33,8 660 X 205 90/68 9
With selector bar
800 x 340 ECSE80UF 40 660 x 205
Overall HT
800 x 340
800 x 340 90/68 7
Mass kgDimensions mm Waterway
areadm2
� DRAINAGE ++++In the lower section of the gut-ter, the bars are arranged longitu-dinally in order to maximize waterdrainage. Simulations carried out ona test bench show increases of between 10 % and15 % in absorption, in certain circumstances, com-pared with a traditional design consisting of a rec-tangular grating and a gully.
SELECTA - C 250Ductile ironClass C 250Locking of the flaps by the elasticity ofductile iron (patented system)Adjustable to pavement levelEN 124
The result of intense cooperation between SAINT-GOBAIN PAM and sewer system managers,the SELECTA gully unit is the professionals’ solutionto the problem of draining rainwater.
� AUTOMATICLOCKING ++++ductile iron springbar integral with grateand cover.
� SCREENING OF DEBRIS ++++The presence of a raised bar preventsaccess into the gully for debris of too largea size and keeps certain solid objects car-ried by run-off water out of the sewer sys-tem.
� SAFETY FOR CYCLISTS ++++On the carriageway, the bars are
perpendicular to the direction of thetraffic in order to ensure safety for
cyclists.
� SAFETY FOR PEDESTRIANS ++++On the pavement side, the elimination of clearanceon the hinge system and of any roughness on the surface of the cover ensure safety for pedestrians(high heels, walking sticks, crutches, etc.).
� ANTI-OBSTRUCTION ++++The surfaces of the bars are equipped with facetsthat are oriented in such a way as to prevent leavesor litter from blocking the drain.
� ADJUSTABILITY ++++Three bolts allow the
height adjustment (up to50 mm) of the cover frame withrespect to the kerb.
Selecta is available in two versions:(a) SELECTA MAXI height adjustable(b) SELECTA 500
- A or T -profile - with raised selector bar grating - with flat grating
(a) (b)
SELECTA Maxi, A-profile with raisedselector bar grating.
SELECTA 500, T-profile with flatgrating
46
SELECTA gully units
47
SELECTA gully units
SELECTA MAXI level adjustment and maximum capacity
SELECTA 500 compact and high-capacity
� SELECTA Maxi gullies are designed for mixed roadway/pavement installation.� Cover and kerb leveled using 3 adjustment bolts integrated into the frame.� Raised selector grating or flat grating.
SELECTA Maxi, A-profile withraised selector bar grating.
SELECTA Maxi, T-profile with raised selector grating SELECTA Maxi,
T-profile with flat grating
SELECTA 500, T-profile withraised selector bar grating
SELECTA 500, A-profile with raisedselector bar grating
SELECTA 500 with T-profile flat grating
H
296 344
h
250 310
h H
250 310
293 347
T-profile
A-profile
T-profile
A-profile
ReferencesTotal Grating Cover Raised section
and frame
ECSE75SFX11 86 25 22 39 9,4 à 10,7
Mass kg Waterway area dm2
according to heightadjustment
A-profile
Kerbprofile
Overall Depth H/h Effectiveopening
Depthadjustment mm
750 x 640 155/90 540 x 450 20
ECSE75UFX11 94 26 24 44 10,1 à 13T-profile 750 x 640 225/90 540 x 450 50
ECSE75UFX16 90 21,3 24 44 11,6 à 14,5T-profile 750 x 640 225/90 540 x 450 50
Dimensions mm
with raised selector bar grating
with flat grating
ReferencesTotal Grating Cover Frame
ECSE61SF 51 16,5 13 21 7,6
Mass kg Waterway areadm2
A-profile
Kerbprofile
Overall Depth H/h Effectiveopening
610 x 570 125/90 385
ECSE61TF 54,5 16,5 14 24 8,5T-profile 610 x 570 205/90 385
ECSE61UF 53 15 14 24 9,8T-profile 610 x 570 205/90 385
Dimensions mm
with raised selector bar grating
with flat grating
� SELECTA 500 drain gullies are fitted on standardized gully pots (500 mm), and are designed formixed roadway/pavement installation.
� Broad soled frame for effective seating on concrete structures. Dimensions compatible with gra-tings, gullies, bases, and concrete kerbing.
� Raised selector bar grating or flat grating
48
Gully units
GULLY COVER PLATES AND INLETS - C 250 Ductile ironClasse C 250 (frame)B 125 (cover)EN 124
COVER PLATESKerb profile Reference
Depth
Profile A
Profile T
ECRV80AF
ECRV80TF 75,6
800 x 830
800 x 830
610
610
120
20024
4,3
6
Dimensions mm Waterway areadm2Total
72
Cover
24
Mass kg
The cover plates are designed to be fitted on large-sized gully pots under pavements (kerb or carriageway combination).
Inlets are simple versions of cover plates without cover.
GULLY GRATING - C 250Ductile ironClass C 250EN 124
These inlet gratings are fitted on small-gully pots (500mm) of a mixed road/pavement type installation. Thegrating’s profile is specially designed to prevent obstructionby leaves or other debris whilst allowing the maximumdrainage.
Overall Clear opening
INLETSKerb profile Reference
Profile A
Profile T
ECAV80AF
ECAV80TF
21
28
800 x 225
800 x 225
120
200
4,2
6
Profile TDimensions mm Waterway
areadm2Overall Hauteur
INLETS GRATINGKerb profile Reference
Total Depth
Profile A
Profile T
ECGA60AF
ECGA60TF
56
62
605 x 502
605 x 502
405
405
176
233
Cover
31
32
8
9,15
Mass kg Dimensions mm Waterway areadm2Overall Clear opening
Ductile ironClass C 250Sloped reinforced frameAvailable with orwithout centring lugSeating flange on 3 sidesEN 124
The COMMUNAL grating is equipped with asloped frame which automatically ensures acrossways slope. The bedding flange on threesides facilitates fitting along the kerb andensures optimum stability. NB : In case of intense traffic, we recomman-de the installation of the range DEDRA 400.See page 39.
Base sizemmType
With lugs
Without lugs
ReferenceTotal Frame Clear opening Depth
500 x 500 ECGP67PFX20 53670 x 600 405 119
500 x 500 ECGP67PFX19 51,5
Grating
23,5
23,511,8
Mass kg Dimensions mm Waterway areadm2
COMMUNAL GRATING C 250
49
Gully units
VBS 2 GULLY - D 400 Ductile ironClass D400Hinged grateEN 124*
VBS2 gullies are complete units which can be used both assiphon and settling vessels. They are directly connected to thedrainage network, made of cast iron or clay. The hinged gratinghas a specially designed profile to improve drainage andprevent obstruction by leaves or other debris.
This device, fitted inshafts topped with alltypes of gratings, acts asan inlet and prevents the
escape of smells. For shafts with insidedimensions of 500 and 700 mm.
ODOR-TIGHT INLETS PAG
Kerb profile Reference
PAG n°2
PAG n°3
ECPG452X
ECPG593X 80
540 x 525
738 x 738
456
590-
Dimensions mm
Total
44
Cover
-
Mass kg
Overall Clear opening
Type Reference
GA 2 450 ECGR34EX 535 X 526
535 X 526GA 2 450 ECGR34EX12
Clear openingmm
NO
YES
Locking
100 350
350
250
100
GB 325 EDGP33EK 535 X 403 NO 100
*Complies with EN 124 functional requirements.
Depthmm
Load resistancekN
9
9
6,9
Waterway areadm2
39
39
39
Masskg
Locking key : C17
Ductile ironHinged on lengthwise with 110° openingReinforced frame, 100 mm deepAnti-theft gratingEN 124*
HINGED GRATES
PROGRESS 2Ductile ironClass C 250Load resistance> 400 kN Hinged grate EN 124*
Progress II gullies are complete units which can beused both as siphon and settling vessels. They exist inan unique size 300x600. Thanks to the levellinginsert the range Progress II offers a very easyimplementation.
Diameter connexionType ofoutlet Reference
Total Depth
160
160
Vertical
Horizontal
EDVB63ECX25
EDVB63ECX24
76,2
78665 x 250 624 x 218 568
Grating
13,8 5,87
Mass kg Dimensions mm Waterway areadm2Vessel Clear opening
Levelling InsertGratingtype
Flat
Flat
Concave
ReferenceTotal Vessel Clear opening Depth
NO
Consult us.
86,8 741x300
840x321
840x321
650x285
550
608
608
YES
YES
110
109,6
Grating
16,1
16,1
16,1
8,1
8,1
8,2
Mass kg Dimensions mm Waterway areadm2
50
Longitudinal channel gratings
SIMPLE ! Easy to install.Gratings are simply snapped intoplace through a ductile springlock.With AUTOLINEA, no accessoriesare needed.
SAFE ! AUTOLINEA provides safety inservice :• no danger of accidental
displacement,• limit vandalism,• anti-dilatation effects.
QUICK ! Removal by professionals is instantaneous, using a crowbaras a lever.
AUTOLINEA D 400
Functional diagrams of AUTOLINEA C 250 locking/unlocking
51
Longitudinal channel gratings
FIELD OF APPLICATION :Street channels along pavements, excluding singular points whichmay be subject to crosswise traffic in the field of class C 250 and forwhich the linked MECALINEA grating is required. (See page 53).
AUTOLINEA D 400
AUTOLINEA C 250
Base sizeReferenceThickness
750 x 200
750 x 250
750 x 300
ECAL20PF
ECAL25PF
ECAL30PF
13
18
22
150
200
250
35
50
56
75
80
85
85
30
7,6
9
11,2
15
20,4
24,6
28,4
750 x 400ECAL40PF 24,8 350
750 x 500ECAL50PF 39 450
750 x 600ECAL60PF 49,5 550
750 x 700ECAL70PF 60 650
Mass kgDimensions mm Waterway
areadm2Clear opening* Depth
AUTOLINEA - D 400 and C 250Ductile ironClasses D 400, C 250Automatic ductile iron spring bar,patented systemEN 124
A brand new generation of channel gratings,AUTOLINEA gratings are linked together by aductile iron spring bar. They are usually installedon cast iron T section frames or steel angle fittingswhich protect the concrete channel and maintainthe support level.
FIELD OF APPLICATION :Channels located at the side of motorways and roads carrying intensetraffic, excluding singular points which may be subject to crosswisetraffic, such as : interchanges, lay-bys, and telephone call stations,breaks in central reservations and crossroads, in which case theTRANSLINEA grating designed for crossing carriageway are required.(See page 52).
Cast iron frame pieces : see page 52.
Reference Base sizeThickness
EDAL40PF
EDAL50PF
750 x 400
750 X 500
33
43
350
45085
15
EDAL30PF 750 x 300 22,9 250 60
35
10,8
20
Mass kgDimensions mm Waterway
areadm2Clear opening* Depth
* when using cast iron T section frame
Gratings for crosswise channels
52
CAST IRON T SECTION FRAME FOR AUTOLINEA D 400 AND TRANSLINEA E 600 / D 400
Note : To ensure that channel gratings in classes D 400 and E 600 provide optimum strength and stability whensubjected to traffic stresses, approval is granted to complete units comprising the grating, its cast iron Tsection frame and, where applicable cast iron end pieces.If other types of T section frame or angle fitting are used, i.e. steel in particular, their dimensioning and theiranchoring in the masonry must be ensured by the specifier, taking into account the stresses due to traffic.
TRANSLINEA - E 600 AND D 400Ductile ironClasses E 600, D 400Mechanical chainingSecuring to channelEN 124
Type ReferenceDepth
Length 750 mm E7 10 750 100
Mass kgLength
TRANSLINEA gratings are used, above all, for crossingcarriageways.They must be installed with the chaining devicesjoining the gratings together and the end piecessecuring the gratings to the channel. This complete,modular system ensures optimum safety undertraffic load. Please see the fitting instructions.
TRANSLINEA E 600Field of application : All areas involving high axle loads such as: aircraft and port areas,plants, in particular.
TRANSLINEA D 400Field of application : all carriageway crossing points, roads carrying intense traffic and othersingular points such as : interchanges, lay-bys and telephone call stations, breaks in centralreservation and crossroads.
ReferenceClass Base sizeArea
EETL40PF
EDTL40PF
E 600
D 400
750 x 400
750 x 400
46
47
350
350
85
85
35
35
12,9
12,9
Mass kgDimensions mm Waterway
areadm2Clear opening* Depth
T SECTION FRAME AND ACCESSORIES SPECIFIC TO TRANSLINEA E 600 / D 400T section frame piece
800 mm long
Cast iron end piece (a)
Chaining device (b)
E8
E10
E9
10,6
4,4
800
400
100
85
Dimensions mm
� b
�
a
* when using cast iron T section frame
53
Other gratings for channels
MECALINEADuctile ironClass C 250Chaining of gratingsEN 124
MECALINEA gratings are traditional gratings withmechanical chaining that are installed on cast iron Tsection frame or steel angle fittings.
Field of application : as per class C 250 :street channels along the side of pave-ments and, in particular, singular pointswhich may be subject to crosswise trafficand where chaining is necessary.
Thickness
150
200
250
300
350
450
550
550
40
45
50
60
60
55
60
65
27
5,8
6,8
9
10,2
12,9
15,9
18,9
21,8
Dimensions mm Waterway areadm2Clear opening* Depth
Reference Base sizemm
750 x 200
750 X 250
750 X 300
750 X 350
750 X 400
750 X 500
750 X 600
750 X 700
ECML20PF
ECML25PF
ECML30PF
ECML35PF
ECML40PF
ECML50PF
ECML60PF
ECML70PF
16,1
21,5
26
30
35
42
54
67
750 X 400
750 X 600
ECML40RF
ECML60RF
35
54
350
550
60
6027
11,8
18,6
Mass kg
GRATINGSWITH BARS
GRATINGS WITHROUND HOLES
* when using cast iron T section frame
Type Reference
Frame pieces
Connecting piece
E5
E6
4
0,5
750
-
27
75
Mass kgDimensions mm
Length Depth
ACCESSORIES FORMECALINEA GRATINGS
Surface Boxes
SAINT-GOBAIN CANALISATION proposes four separate product ranges which cater to different requirements.Specific catalogue available on request
54
PAVA EXTENDABLE SURFACE BOXES
Type
PAVA 10PAVA 14PAVA 19
Extendibility
105
184
140
Reference
F1PVAC
F2PVAC
F3PVAC
H1
145
250
192
H2
145
250
222
ø DI
102
102
120
A
240
240
300
C
220
220
282
ø DI’
137
137
148
ø B
114
114
162
D
147
147
216
Weight
8,4
13,1
19
PAVA surface boxes feature built-in extension capabilitiesThe lower base of the body features screw-nut type threads and is desi-gned to allow the unit to be raised during road resurfacing operationsby simply “unscrewing” the assembly.The design includes� A self-locking system which prevents the lid from being removed
by street cleaning equipment or by acts of vandalism � A wide base reduces the risk of subsidence under traffic loads: stabi-
lity and silence of the lid on its seat� Side bonding ribs at the base of the body to prevent rotation during
extension operations
Designed to simplify the extension operation, the lids of the PAVA10 and 14 can be turned over and used as a tool to limit the ope-rating force. Equipped with two studs forming an operating nut, theinside face of the lid can be used to adjust the extension heightusing a plain 30 mm wrench or with a Tee wrench used for valveoperation. The PAVA 19 requires the use of a specific operating lid. Reference: F3PVRC-T
* Other lid versions and options (shape and chain) are available : please contact us for details
30 at installation Seal
LidBody
Base
105 184 140
PAVA
10
PAVA
19
PAVA
14
mm
EXTENSION CHARACTERISTICS
Round
Square
Rectangular
Hexagonal
55
Surface Boxes
Type
SidewalkStreet
Extension
FTTOBB
FRTOBB
FRTO63V
FTTODB
FRTODB
FRTO63W
H
160
160
166
ø A
150
210
74
ø DI
102
102
63
ø E
77
77
63
ø D
120
140
170
Masse
3,3
5,2
3,6
References
Square HexagonalRoundFTTOAB
FRTOAB
FRTO63U
Type
Street roundStreet hexagonal
Street square
H
180
180
180
ø A
250x220
250x220
250x220
ø DI
102
102
102
ø E
84
84
84
ø D
140
140
140
Weight
6,4
6,4
6,5
References
FRXBACT
FRXBDCT
FRXBBCT
Type
RoundSquare
Hexagonal
H
370
370
370
ø A
-
-
-
ø DI
68
68
68
ø E
68
68
68
ø D
200
200
200
Weight
7
6,75
7
References
FRRHACT
FRRHBCT
FRRHDCT
TOTALE SURFACE BOXES RANGE
THE TOTALE MAXI SURFACE BOXES
HEIGHT ADJUSTABLE SURFACE BOXES
Two versions are available: “Sidewalks and streets”. The base of the “street” version offers a wide bea-ring surface for enhanced stability under traffic loads.
Surface boxes with “water” badging have a hook-opener type lid with no through hole, chainless*
*Other lid versions and options are available: please consult us for details
Height adjustable surface boxes (used as Extension for TOTAL MAXI)
H
D
Sidewalk Street Extension
ACCESSORIESReference
162 098
Type
Hammer for surface box
Euro
Dial
og’P
artn
ers •
F-CA
T-01
A-DC
E . 0
1/08
. 300
0 ex
.
The
draw
ings
, illu
stra
tions
and
wei
ghts
giv
en in
this
bro
chur
e ar
e no
n-co
ntra
ctua
l. SA
INT-
GO
BAIN
CAN
ALIS
ATIO
N r
eser
ves
the
righ
t to
chan
ge p
rodu
ct s
peci
ficat
ions
as
a re
sult
of p
rodu
ct im
prov
emen
ts w
ithou
t pri
or n
otic
e.
An international group with facilities throughout the world,Saint-Gobain Pipe Division has a large sales networkthrough its industrial and sales companies and its agents.Our technicians and professional engineers are available toprovide technical assistance to customers throughout theworld :
• Design advice- engineering calculations- hydraulic calculations- water analyses- soil studies
• Site assistance• After-sales service
For any further information about covers and gratings,please contact our Municipal Castings Business Unit
SAINT-GOBAIN PAMHead office91, avenue de la Libération 54076 NANCY CEDEX France
Municipal Castings Business Unit21, avenue Camille Cavallier 54705 PONT À MOUSSON CEDEXTél. : +33 (0) 3 83 80 73 50Fax : +33 (0) 3 83 80 07 08