MAKE OR BUY DECESION FOR FILM COATING MATERIAL 1. Consistency In ColourIn Colour a.Advanced colour...
-
Upload
wesley-freeman -
Category
Documents
-
view
215 -
download
2
Transcript of MAKE OR BUY DECESION FOR FILM COATING MATERIAL 1. Consistency In ColourIn Colour a.Advanced colour...
MAKE OR BUY DECESION
FOR
FILM COATING MATERIAL
1. Consistency1. Consistency1. Consistency1. ConsistencyIn Colour
a. Advanced colour matching system. Once a shade is produced It is stored in the system for reproducibility.b. Over 30 years experience in colour producing and matching.c. Jet Milled Colours. Offering uniform particle size & even distribution of colour.
In uniformity of film thicknessa. Better homogenization of all the constituents of The film coating systems.b. Optimised concentration of Polymers &
Plasticiser
2. Problems in preparation at your2. Problems in preparation at your shop floor shop floor 2. Problems in preparation at your2. Problems in preparation at your shop floor shop floor
a. To many ingredients to be dispensed especially if the product is coated in different lots.
b. Colour uniformity has to be constantly monitored.c. Colloid milling is a must so as to avoid colour variation.d. Skilled workers are always required to be present during all
the steps of the coating operation.e. Prepared coating suspensions once stored beyond 36 hours
have to be colloid milled again before use,could lead to shade variation.
3. Saving in Time3. Saving in Time3. Saving in Time3. Saving in TimeIn Production
a. Higher Reconstitution level up to 20%b. Coating solution preparation is single step stirring process.
In faster introduction of new products
a. Samples of the Coating material and Coated tablets in various shades are made available immediately on request, thereby eliminating the need of spending your R&D time.
b. Your product range can have various colours for brand identification.
44. . Multiple sources vs. single Multiple sources vs. single source of supplysource of supply 44. . Multiple sources vs. single Multiple sources vs. single source of supplysource of supply
a. As against different sources for supply of different ingredients of Film Coating material there is a single source offering many advantages.
5. Fixing Responsibility for quality of Raw materials
• Multiple suppliers are involved and responsibility for bad quality cannot be pinpointed.
• We give technical backup unlike suppliers involved in multiple sourcing
• Being our own formula we take the complete responsibility for your product problems due to bad coating.
6. BENEFITS OF CONTINUOUS R & D6. BENEFITS OF CONTINUOUS R & D Latest polymers and their combinations are thoroughly studied for various properties Optimized plasticizers are selected on the film studies done in our R & D. Latest ingredients are used to improve sheen and gloss. Constantly improving film forming process and materials is the hallmark of our R & D. We build quality in our product by choosing our items from international vendors with superior technical backup.
1 Floating Enquiry 8 Inventory holding space
2 Comparision 9 Maintaining minimum level
3 Ordering 10 Ordering minimum quantity
4 Follow up for delivery 11 Q.C. Analysis
5 Gate Entry 12 Q.C. Reports
6 Preparation of GRN 13 Accounting Entries
7 Entry in Bin Card 14 Payments
RAW MATERIAL IN COATING : PURCHASE TO APPROVALRAW MATERIAL IN COATING : PURCHASE TO APPROVALRAW MATERIAL IN COATING : PURCHASE TO APPROVALRAW MATERIAL IN COATING : PURCHASE TO APPROVAL
1 Identification 15 Dye content 1. pH 2 Assay 16 Free dye content 2.Particle size 3 PH 17 Viscosity 3.Bulk density 4 Particle size 18 Free ethylene oxide and 1,4 dioxane 4.Appearance 5 Heavy Metals 19 Limit test for ethylene glycol 5.Ash content 6 Sulfated ash 20 and diethylene glycol 6.Arsenic 7 Lead 21 Average molecular weight 7.Heavy metals 8 Solubility 22 Acid soluble substances 8. Viscosity 9 Loss on drying 23 Organic volatile impurities
10 Microbiological tests 24 Assay HPMC-- Methoxy and Hydroxy
11 Arsenic 25 IR
12 Monomer test 26 Refractive Index
13 Water soluble subs. 27 Specific Gravity
14 Botanical Characterstics 28 Melting Point
TESTS DONE ON MULTIPLE INGREDIENTSTESTS DONE ON MULTIPLE INGREDIENTSTESTS DONE ON MULTIPLE INGREDIENTSTESTS DONE ON MULTIPLE INGREDIENTS
TESTS ON SINGLE SOURCETESTS ON SINGLE SOURCETESTS ON SINGLE SOURCETESTS ON SINGLE SOURCE
1. pH2. Particle size3. Bulk density4. Appearance5. Ash content6. Arsenic7. Heavy metals8. Viscosity
STEPS IN MULTIPLE SOURCE INHOUSE FORMULA PRODUCTION.
Steps % wastage
Dispensing in stores 0.1Sieving of ingredients 0.4Preparation of pigment suspension 0.6Preparation of Lacquer solution 0.5Mixing of pigment and lacquer solution 0.2Filteration through fine nylon mesh 0.2
Total 2
COST EFFECTIVENESSCOST EFFECTIVENESS
DIRECT COSTRaw Material
Utilities
Labour
IN DIRECT COST Cost of Order Processing& Inventory holding
Cost of Analysis
Cost of Rejections/ Rework
COST EFFECTIVENESSCOST EFFECTIVENESS
OTHER APPORTIONABLE COST
Benefit of Continuous R&D
Single source responsibility& Tech. Service
Avoidance of Problems in manufacturing& Preparation
Faster Introduction ofNewer Products
S.N.Name of the Raw Material
Price per KG*
% used Total Cost % used Total Cost
1 HPMC 6cps 975 60 585 60 5852 PEG 6000 325 13 42.25 13 42.253 TIO2 365 18.4 67.16 11 40.154 Talc 16 7 1.12 5 0.85 Sorbic Acid 100 0.6 0.6 0.6 0.66 Tween 80 80 1 0.8 1 0.87 Lake Quinoline Yellow 4300 9.4 404.2
TOTAL 100 696.93 100 1073.8
* Excludes Excise Duty & sales tax
WHITE LIGHT YELLOW
S.N.Name of the Raw Material
Price per KG*
% used Total Cost % used Total Cost
1 HPMC 15cps 975 60 585 60 5852 PEG 6000 325 13 42.25 13 42.253 TIO2 365 18.4 67.16 8 29.24 Talc 16 7 1.12 7 1.125 Sorbic Acid 100 0.6 0.6 06 Tween 80 80 1 0.8 1 0.87 Lake ALLURA RED 1450 11 159.5
TOTAL 100 696.93 100 817.87
* Excludes Excise Duty & sales tax
WHITE PINK/ ALLURA RED
S.N. Description % Cost White Cost Yellow Other
1 Raw Materials 696.93 1073.80 817.872 Add Wastage 1 6.97 10.74 8.183 Add Cost of Ordering & Inventory holding 8 55.75 85.90 65.434 Cost of Analysis 2 13.94 21.48 16.365 Labour Cost for preparation & Supervision 8 55.75 85.90 65.436 Utility Cost 5 34.85 53.69 40.897 Add Allocation of other indirect overheads 10 69.69 107.38 81.798 Development Cost/ Cost of Technology 0.00 0.00 0
TOTAL 933.89 1438.89 1095.95