MAINTENANCE & REPAIR GUIDE - BuildSite · ShapeShift pitch pans are approved for installation on...
Transcript of MAINTENANCE & REPAIR GUIDE - BuildSite · ShapeShift pitch pans are approved for installation on...
MAINTENANCE
& REPAIR GUIDE ROOFING PRODUCTS & SYSTEMS
See page 39
Product Spotlight
2
The ShapeShift® line consists of three primary products: ShapeShift Straight or Corner Pitch Pans and MP Liquid Sealant.
ShapeShift Pitch PansShapeShift pitch pans consist of straight and outside corner sections snap together to create an endless number of pitch
pan sizes to seal around roof projections. The radius corner pieces measure approximately 2" x 2". The straight sections
measure approximately 3" long. The high-strength polymer pieces have a 2-1/2" base lange with a 1-3/4" high side. The
pieces snap together with interlocking joints.
ShapeShift pitch pans are approved for installation on Mule-Hide warranted projects when installed on vertical surfaces if
illed with JTS 1 sealant instead of MP Liquid Sealant.
MP Liquid SealantA 100% solids, non-shrink, one-part semi-selleveling polyurethane pourable sealer seals:
• Metal roof seams and fasteners
• Gutters
• Damaged polyurethane foam
• Roof projections on PVC, EPDM, primed TPO, primed Mod Bit and primed
BUR rooing systems
See page 17
3
See page 38
RGA 1 is a rubberized flashing cement used to seal: • SBS mod bit seams, laps and perimeter edges
• Splits, cracks, blisters, metal langes and punctures in asphalt-based roof
membranes and lashings
• Sealing tabs, edges, step lashings and valleys in shingled roofs
• Sealing seams and edges in rubberized waterprooing projects
• Sealing concrete or brick at chimney lashings
During Application
Mortar Sentry Water Seal is designed for use on brick, mortar, concrete
block, cultured stone, sandstone and concrete. It is not recommended for use on
non-silicate natural stone such as limestone or dolomite.
Mortar Sentry is a silane/siloxane based waterprooing treatment consisting of two
products. Mortar Sentry Water Seal 10 is for vertical surfaces and Mortar Sentry
Water Seal 15 is for horizontal surfaces.
TABLE OF CONTENTS
Product Spotlight 2-3
M&R Selling Staion 5
End Caps 6-7
EPDM Accessories 8-11
TPO Accessories 12-13
No-Weld TPO 14-15
Sealants & Caulkings 16-17
White Coatings
Silicone 19-21
Elastomeric Acrylic 22-25
SEBS 26-29
Asphalt Cements & Coatings 30-34
Seal-Fast Tapes 35-37
Waterproofing 38
Accessories 39
4
M&R SELLING STATION
Maintenance & Repair Plan-o-gram
(15) 121
Asphalt Primer
(4) Seal-Fast® Fabric Tape
(9) EPDM Tape Primer
Quart Cans
(8) EPDM Uncured Flashing Tape
(8) EPDM Cured Cover Tape
(6) Seal-Fast® Temporary Low-Slope
Roof Sealer
(4)
Sea
l-Fa
st
Spr
ay P
rim
er
(18) 271 Mod Bit
Sealant
Items in yellow will ship with display
(50) Single-Ply
Accessories Catalogs
(30) Maintenance
& Repair Slide Charts
(1) Aluminator Roof Drain
A
16"
10"
9"
10-1/2"
11-1/2"
(10) EPDM 1”-6” Black Pipe boot w/tape
(15) EPDM In-Seam
Tape 3” x 25’
(6) Seal-Fast
Tape Black
4”x 50’
(4)
Seal-Fast
Tape
Black
6”x 50’
(80) Pre-Cut Inside/Out-
side Corners(20 per box)
(24) 4” Pourable Sealer Pockets
(6) Tape Primer
(25)
Water Cut Off
(25) Black Lap Sealant
(4) Acrylic Water Base Bonding Adhesive
(4) Weathered Membrane
Cleaner
B
15"
12-1/2"
8-1/2"
13"
12-1/2"
8"
(15) Seal-Fast®
Tape White
3” x 50’
(6) Seal-Fast®
Tape White
6”x 25’
(6) Seal-Fast®
Tape White
6”x 50’
(20) TPO Universal Corner
White
(5) Molded Pourable Sealant Pocket
(100) TPO
T-Joint(1 box)
(8) TPO Cut
Edge Sealant
(12) Seam Probe
(6) TPO Primer
(24) Universal Single-Ply
Sealant
(8) TPO 3/4”-8” Pipe
Boot White
(4) EPDM One-Part
Pourable Sealer Black (4-per container)
(4) Thermo Pourable
Sealant White
(4-per container)
C
14-1/2"
13-1/2"
9"
13"
6-1/2"
10"
(4) 100% Silicone Roof Coating
(4) 100% Silicone Sealant
(4) A-300 Finish
Elastomeric Acrylic Coating
(4) A-200 Flashing
Elastomeric Acrylic Coating
(2) TieTex® 325 12” x 300’
(1)
211 Plastic Cement
(1) 241 Premium Modified
Flashing Cement
(1)
221 Wet/Dry Plastic
Cement
(1) 421 Mod Bit
Flashing Adhesive
(4) TieTex® 325
6” x 300’
D
18"
14"
9"
9"
9"
9"
***Approximate Measurements
This side of display can have empty pails upon request. If that is the case we will have
additional products from Silicone Coatings and Elastomeric Acrylic Coating represented
**The products shown on this display are recommended by Mule-Hide but can easily be changed out with products that are more specific for your location.
5
END CAPS
6
End Caps are a great way to add to your showroom. We have several available: M&R, EAC, Silicone & Drains. For details about these programs please contact your local Territory
Manager or Customer Service at 800-786-1492.
NOTES
7
EPDM ACCESSORIES
LOW-VOC BONDING ADHESIVE A high strength solvent-based contact
adhesive that allows bonding of EPDM and
TPO to various porous and non-porous
substrates. Specially formulated using a
blend of VOC exempt and non-exempt
solvents to be meet the < 250 g/L VOC
content requirements of the OTC Model Rule
for adhesives and sealants.
Product Code Description Coverage Shelf Life
08MHETBLV1 1-Gallon Pail (6/ctn) 60 sq.ft. per gallon 1 year
EPDM TPO
EPDM IN-SEAM TAPE A black or white, butyl rubber-based adhesive
in tape form. Formulated to provide high green
strength in both shear and peel. May be used
on ballasted, mechanically attached and fully
adhered EPDM rooing systems.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Shelf Life
08MHINSMT2 Black 3" x 25' 12 per 1 year
EPDM
Product Code Description Size Carton Weight Shelf
Life
08MHLAT625 Black 6" x 25'
roll4 per 25 lbs. 1 year
08MHLAT62W White
CURED COVER TAPE A nominal 60 mil, cured EPDM membrane
strip laminated to nominal 30 mil cured
butyl rubber tape and rolled onto a release
liner, for a total nominal thickness of 90 mil.
Commonly used to strip in metal edging.
Requires the use of Tape Primer
or Low VOC Tape Primer.
EPDMEPDM
UNCURED FLASHING TAPE May be used in conjunction with the Mule-
Hide Tape Primer to lash inside and outside
corners, pipes, pitch pockets or other
penetrations that require the lashing to be
molded or conform to an irregular shape.
Not permitted for use in lashing gravel
stops, drip aprons or stripping seams or
batten bars.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Weight Shelf Life
08MHUT062B 6" X 25' Black 8 per 38 lbs. 6-9 months
8
WATER CUT-OFF MASTIC Used to seal rooing membranes to stop
water penetration into the rooing system.
Common uses are at drain terminations and
behind Mule-Hide All Purpose Bars at wall
terminations.
EPDM TPO PVC
Product Code Description Weight Coverage Shelf Life
08MHWTRC11-oz Tube
(25 per carton)27 lbs.
10 Ln.ft.
with 1/2" bead1 year
PRE-CUT INSIDE/OUTSIDE CORNERS Ideal for installing inside and outside corners.
Consists of .060 inch (1.5 mm) thick uncured
EPDM lashing material laminated to cured butyl
rubber tape and rolled onto a poly release liner
providing .090 mils (2.25 mm) of total thickness.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Weight Shelf Life
08MHPCC20 7” x 9” 20 per 5 lbs. 9 months
EPDM
POURABLE SEALER POCKETS Ideal for sealing irregular, hard to lash
penetrations through the membrane.
Prefabricated pockets consisting of a 2" (50
mm) wide plastic support strip with attached
Uncured EPDM Flashing Tape.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Weight Shelf Life
08MHPSP4 4” Black12 per
4 lbs.9 months
08MHPSP6 6” Black 5 lbs.
EPDM
PREMOLDED EPDM PIPE BOOTS Accommodates single pipe sizes from 1"
to 6" in diameter. Conical-shaped steps
securely seal all single pipe penetrations. The
large, double-thick, molded rib at the top of
each step offers superior tear-resistance and
reinforcement, as well as a cutting guide.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Size Weight Shelf Life
08MHPBTB6TBlack with clamps
and tape rings10 per 1"- 6" 8 lbs. 1 year
EPDM
BLACK ONE-PART POURABLE SEALER Designed for use with EPDM Pourable
Sealant Pockets. The sealant’s one-part,
pourable consistency allows for quick
pocket illing without mixing.
Product Code Description Weight Coverage Shelf Life
08MHPSOPBK1/2-Gallon Pouches
(4 per carton)26 lbs. 200 cu.in. 1.5 years
EPDM
EPDM BLACK LAP SEALANT Required for sealing EPDM seams and
lashings against the effects of weathering
when seamed with Splice Adhesive or All
Purpose Single Seal Adhesive. Refer to the
Mule-Hide EPDM Manual for appropriate use
of Lap Sealant when seams and lashings are
completed with Mule-Hide tape products.
EPDM
Product Code Description Carton Coverage Shelf Life
08MHLPCB 11-oz Tube 25 per22 Ln.ft. with
5/16" bead1 year
9
10
EPDM ACCESSORIES
UNIVERSAL SINGLE-PLY SEALANT A 100% solids, solvent free, one-part,
polyether sealant that provides a weather
tight seal to a variety of building substrates.
Provides excellent adhesive to substrates
such as stone, masonry, ceramic, marble,
wood, steel, aluminum, most plastics and
composites. Not recommended as a glass-
glazing sealant.
Product Code Description Weight Coverage Shelf Life
08MHUSPSWH10.1-oz Tube
(24 per carton)24 lbs.
25 Ln.ft.
with 1/4" bead1 year
TAPE PRIMER A solvent-based product designed for one-
step cleaning and priming of EPDM surfaces
to be bonded with In-Seam Tapes, Uncured
Flashing Tapes, Cured Cover Tapes and Pre-
Taped membranes.
EPDM
Product Code Description Carton Coverage Shelf Life
08MHTAPR1 1-Gallon Pail 6 per 250 sq. ft. per
gallon9 months
08MHTAPRQ 1-Quart Can 8 per
LOW VOC PRIMER A low-VOC product designed for one-step
cleaning and priming of EPDM and TPO
surfaces prior to the application of In-Seam
Tapes and other taped products. Specially
formulated using a blend of VOC exempt and
non-exempt solvents to be meet the < 250 g/L
VOC content requirements of the OTC Model
Rule for adhesives and sealants.
EPDM TPO
Product Code Description Carton Coverage Shelf Life
08MHEPLV1 1-Gallon Pail 6 per 250 sq. ft. per
gallon9 months
08MHEPLVQ 1-Quart Can 8 per
11
NOTES
TPO ACCESSORIES
12
TPO
TPO PIPE SEALS Designed as an economical lashing for
single pipe penetrations on Mule-Hide TPO
Membrane roof systems. TPO Pipe Seals
can be used wherever the TPO Pipe Seals
may be slipped over the top of the pipe.
Product Code Description Size Carton Weight
08MHTP348W White 3/4” to 8” OD 8 per 8 lbs.
TPO
T-JOINT COVER Used to seal step-offs at splice
intersections. Installation is mandatory on
all 60 mil and 80 mil TPO systems and on
45 mil systems where step-offs have not
been properly sealed.
Product Code Description Size Carton Weight
08MHTTJPWH White 4.5” circle 100 per 3 lbs.
13
THERMOPLASTIC ONE-PART POURABLE SEALER (WHITE) Designed for use with TPO, PVC & EPDM
Pourable Sealer Pockets. The sealant’s one-
part, pourable consistency allows for quick
pocket illing without mixing.
Product Code Description Weight Coverage Shelf Life
08MHTPSWHE1/2-Gallon Pouches
(4 per carton)29 lbs. 122 cu.in. 1 year
EPDM TPO PVC
TPO
MOLDED SEALANT POCKETS Interlocking, two-piece prefabricated
pockets of non-reinforced TPO material
used to seal pipe clusters or other
irregular shaped penetrations. Pockets
length can be adjusted from 7-1/2" to
11-1/2" by following the pre-molded
cutting lines.
Product Code Description Size Carton Weight
08MHTMSAPW White 7-1/2" to 11-1/2" 5 per 4 lbs.
TPO
UNIVERSAL CORNERS Uniform in shape and size and provide
water tightness at corners formed by
TPO coated metal and/or TPO lashing
membrane. Provides a neat, inished look
to building corners, curbs and parapet
lashings with no cutting or stretching
required.
Product Code Description Carton Weight
08MHTUCWHE White 20 per 5 lbs.
TPO
TPO TAPE PRIMER A solvent-based product designed for
one-step cleaning and priming of TPO
surfaces to be bonded with In-Seam
Tapes, Uncured Flashing Tapes, Cured
Cover Tapes, and Pre-Taped membranes.
It is specially formulated using a blend of
VOC exempt and non-exempt solvents
to be meet the < 250 g/L VOC content
requirements of the OTC Model Rule for
adhesives and sealants.
Product Code Description Carton Coverage Shelf Life
08MHTMP1 1-Gallon Pail 6 per 250 F2 per gallon 1 year
Product Code Description Coverage Carton Shelf Life
08MHTCESCE 16-oz Bottle250 -275 lf
1/8” bead8 per 1 year
08MHTCELVE 16-oz Bottle250 -275 lf
1/8” bead8 per 1 year
TPO CUT-EDGE SEALANT A thermoplastic compound designed for use
at the edge of cut Mule-Hide TPO membrane
seams after the membrane has been welded
to itself or to Mule-Hide TPO Coated Metal.
LOW-VOC CUT-EDGE SEALANT *Meets California & Utah VOC regulations
TPO
WEATHERED MEMBRANE CLEANER Used to clean in-service EPDM membrane that
has been exposed to the weather and clean
TPO membrane prior to the welding process.
Helps to loosen and remove dirt and other
contaminants from the surface of the EPDM and
TPO membranes and leaves a suitable surface
for welding or the subsequent application of
Tape Primer. LOW-VOC WEATHERED MEMBRANE CLEANER *Meets California & Utah VOC regulations
Product Code Description Carton Coverage
08MHTWMC1 1-Gallon Pail 2 per
400 sq.ft. (1-side)
per gallon
08MHTWMC5 5-Gallon Pail 1 per
08MHTLVMC1 1-Gallon Pail / Low-VOC* 2 per
08MHTLVMC5 5-Gallon Pail / Low-VOC* 1 per
EPDM TPO
NO-WELD TPO PRODUCTS
WHITE UNCURED FLASHING TAPE May be used in conjunction with the Mule-
Hide Tape Primer to lash inside and outside
corners, pipes, pitch pockets or other
penetrations that require the lashing to be
molded or conform to an irregular shape.
Not permitted for use in lashing gravel
stops, drip aprons or stripping seams or
batten bars.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Weight Shelf Life
08MHUT095W 9" x 50' White 1 per 15 lbs.6-9 months
08MHUT125W 12" x 50' White 1 per 20 lbs.
THERMOPLASTIC ONE-PART POURABLE SEALER (WHITE) Designed for use with TPO, PVC & EPDM
Pourable Sealer Pockets. The sealant’s one-
part, pourable consistency allows for quick
pocket illing without mixing.
Product Code Description Weight Coverage Shelf Life
08MHTPSWHE1/2-Gallon Pouches
(4 per carton)29 lbs. 122 cu.in. 1 year
Product Code Description Carton Weight Shelf Life
08MHMLW061 6" x 100' roll 2 per 45 lbs.
1 year08MHMLW126 12" x 65' roll1 per
27 lbs.
08MHMLW121 12" x 100' roll 45 lbs.
MATE-LINE TAPE Speciically developed for use with EPDM
single-ply membrane rooing systems. May
be used in conjunction with the Mule-Hide
Tape Primer to strip gravel stops, drip
aprons, seams or batten bars, and can be
used to make repairs.
Requires the use of Tape Primer
or Low VOC Tape Primer.
EPDM
UNIVERSAL SINGLE-PLY SEALANT A 100% solids, solvent free, one-part,
polyether sealant that provides a weather
tight seal to a variety of building substrates.
Provides excellent adhesive to substrates
such as stone, masonry, ceramic, marble,
wood, steel, aluminum, most plastics and
composites. Not recommended as a glass-
glazing sealant.
Product Code Description Weight Coverage Shelf Life
08MHUSPSWH10.1-oz Tube
(24 per carton)24 lbs.
25 Ln.ft.
with 1/4" bead1 year
14
TPO
EPDM TPO
WHITE POURABLE SEALER POCKETS Prefabricated pockets consisting of a 2" (50
mm) wide plastic support strip with attached
Uncured EPDM Flashing Tape ideal for sealing
irregular, hard to lash penetrations through
the membrane. Use Mule-Hide Thermoplastic
One-Part Pourable Sealer as a white iller.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Weight Shelf Life
08MHPSP6WH 6" White 12 per 6 lbs. 6 months
15
WHITE PREMOLDED EPDM PIPE BOOTS Accommodates single pipe sizes from 1"
to 6" in diameter. Conical-shaped steps
securely seal all single pipe penetrations. The
large, double-thick, molded rib at the top of
each step offers superior tear-resistance and
reinforcement, as well as a cutting guide.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Size Weight Shelf Life
08MHPBTW6TWhite with clamps
and tape rings10 per 1"- 6" 10 lbs. 1 year
EPDM TPO
WHITE PRE-CUT INSIDE/OUTSIDE
CORNERS Ideal for installing inside and outside corners.
Consists of .060 inch (1.5 mm) thick uncured
EPDM lashing material laminated to cured butyl
rubber tape and rolled onto a poly release liner
providing .090 mils (2.25 mm) of total thickness.
Requires the use of Tape Primer
or Low VOC Tape Primer.
Product Code Description Carton Weight Shelf Life
08MHCPSWH2 7” x 9” 20 per 8 lbs. 9 months
EPDM TPO
WEATHERED MEMBRANE CLEANER Used to clean in-service EPDM membrane that
has been exposed to the weather and clean
TPO membrane prior to the welding process.
Helps to loosen and remove dirt and other
contaminants from the surface of the EPDM and
TPO membranes and leaves a suitable surface
for welding or the subsequent application of
Tape Primer. LOW-VOC WEATHERED MEMBRANE CLEANER *Meets California & Utah VOC regulations
Product Code Description Carton Coverage
08MHTWMC1 1-Gallon Pail 2 per
400 sq.ft. (1-side)
per gallon
08MHTWMC5 5-Gallon Pail 1 per
08MHTLVMC1 1-Gallon Pail / Low-VOC* 2 per
08MHTLVMC5 5-Gallon Pail / Low-VOC* 1 per
EPDM TPO
EPDM TPO
TPO
TPO TAPE PRIMER A solvent-based product designed for
one-step cleaning and priming of TPO
surfaces to be bonded with In-Seam
Tapes, Uncured Flashing Tapes, Cured
Cover Tapes, and Pre-Taped membranes.
It is specially formulated using a blend of
VOC exempt and non-exempt solvents
to be meet the < 250 g/L VOC content
requirements of the OTC Model Rule for
adhesives and sealants.
Product Code Description Carton Coverage Shelf Life
08MHTMP1 1-Gallon Pail 6 per 250 F2 per gallon 1 year
Product Code Description Size Carton Weight Shelf Life
08MHLAT62WWhite
6" x 25'
roll4 per 25 lbs. 1 year
CURED COVER TAPE A nominal 60 mil, cured EPDM membrane
strip laminated to nominal 30 mil cured
butyl rubber tape and rolled onto a release
liner, for a total nominal thickness of 90 mil.
Commonly used to strip in metal edging.
Requires the use of Tape Primer
or Low VOC Tape Primer.
EPDM
JTS 1 SEBS 1 Si Sealant
Ideal Application
Large joints & termination bars for concrete, masonry, EPDM,
PVC, TPO (primed), wood, vinyl and most other common
building materials
Metal repair & restoration, for use with the SEBS Roof
Coating System
Single-ply membrane, modiied restoration, metal, SPF, for use with the Silicone Roof Coating
System
Common UsesSealing penetrations for
residential rooing; adheres to wet and underwater surfaces
Multipurpose use on all types of roofs including EPDM, TPO,
ModBit, Kynar®, shingles, asphalt, concrete, masonry, tile
General waterprooing and mildew-resistant applications; seams, fasteners, windows,
doors, gutters, siding
Colors *Reference p.17 for color chart
8 - Colors
White, Black, Bronze, Medium Bronze, Gray, Limestone, Wicker/Tan, Terra Cotta
13 - Colors
Pure Clear, White, Black, Bronze, Medium Bronze,
Gray, Dark Gray, Limestone, Sandstone, Wicker/Tan, Musket Brown, Royal Brown, Aluminum
2 - Colors
White, Clear
Packaging Plastic Tubes, 12 per box
Type Moisture-cure urethane sealant made with 100% solids
Thermoplastic elastomer-based, solvent-based terpolymer
sealant
High-solid, non-shrinking, oxime silicone sealant
Elongation & Tensile Strength 400%, 400 psi
1,000%, 700 psi (700%, 700 psi – Pure Clear)
500%, 200 psi
Max. joint size 2-inch 3/8-inch 1-inch
Skin time 30 minutes 30 minutes 10 minutes
Tack-free 2 hours 3 hours 1 hour
VOC 8 g/L, less than 1.5% Less than 300 g/L 10 g/L, less than 3%
Shelf Life 2 years 5 years 1 year
Viscosity 1,500,000 cps 1,800,000 cps 700,000 cps
Tensile Strength The maximum stress the material will sustain before fracture. The tensile strength is calculated by dividing the maximum load by the original cross-sectional area of the test specimen.
Elongation The increase in the gauge length, measured after fracture of the specimen within the gauge length, usually expressed as a percentage of the original gauge length.
SEALANTS & CAULKINGS
16
Product Code Color Coverage Carton Shelf Life
30MHJTS1WH White
25 LF/Tube(12) 10 oz
tubes/ctn2 years
30MHJTS1BK Black
30MHJTS1MB Medium Bronze
30MHJTS1BZ Bronze
30MHJTS1GY Gray
30MHJTS1LS Limestone
30MHJTS1WT Wicker/Tan
30MHJTS1TC Terra Cotta
JTS 1 JOINT & TERMINATION SEALANT JTS 1 is a moisture-cure urethane
sealant made with 100% solids. JTS 1
seals large joints, roof termination bars
and adheres to concrete, masonry,
EPDM, PVC, TPO (primed), wood,
vinyl and most other common building
materials.
SEBS 1 Is a high-performance, multipurpose thermoplastic elastomer-based rooing sealant. Provides excellent adhesion to most surfaces including the list above. Use to seal seams, lashings and penetrations on all types of roofs. Ideal for rooing applications where appearance is important.
Removable Tip
Product Code Color Coverage Carton Shelf Life
30MHSEB1WH White
See Product
Data Sheet
(12) 10 oz
tubes/ctn5 Years
30MHSEB1BK Black
30MHSEB1GY Gray
30MHSEB1DG Dark Gray
30MHSEB1CY Clay
30MHSEB1SA Sandstone
30MHSEB1WT Wicker/Tan
30MHSEB1MB Medium Bronze
30MHSEB1MU Musket Brown
30MHSEB1RB Royal Brown
30MHSEB1BZ Bronze
30MHSEB1AL Aluminum
30MHSEB1PC Pure Clear
Product Code Color Description Coverage Shelf Life
16MHSISECL Clear 1 tube (12/ctn) See Product
Data Sheet1 Year
16MHSISEWH White 1 tube (12/ctn)
SILICONE ROOF SEALANT Is a high solids non-shrinking moisture
cure silicone sealant that has minimal
odor, contains no solvents and has less
than 10 grams per liter VOC. Provides
excellent adhesion to concrete, masonry,
polyurethane foam, EPDM, TPO, aged
PVC, aged acrylic coatings, granular cap
sheet, wood, metals, Kynar® Finishes and
most other common building materials.
Mule-Hide Si TPO Primer is required for
TPO roof membranes. Removable Tip
White
Black Bronze Medium Bronze
Gray
Limestone Wicker/Tan
Terra Cotta Aluminum
Sandstone
ClayDark GrayRoyal BrownMusket Brown
Color Options: * Colors shown are matched as accurately as possible, but may vary slightly from finished product.
Pure ClearClear17
Product Code Color Description Coverage Shelf Life
16MHRGA1BT Black 1 tube (12/ctn) See Product
Data Sheet2 Years
RGA 1 Flashing Cement is the highest quality,
most versatile asphalt based roof cement
ever developed. This distinctive product is
intended for use by quality driven rooing
professionals who demand that their
materials meet the highest performance
standards. Its outstanding adhesion to wet,
dry and even underwater surfaces allows
application in any conditions. With wider
usable temperature ranges, RGA1 applies
easily at seasonal temperature extremes. Removable Tip
WHITE COATINGS
Roof CoatingsComparison Chart
18
EAC SEBS Silicone
Ideal Application Metal, EPDM restoration Metal repair, restorationSingle-ply membrane, modiied
restoration, metal
Colors
Standard Colors - White, Dark Gray, Light Gray,
Tan, Beige
Standard Special Order - Medium Bronze, Royal Brown, Dark Gray,
Sandstone,Terra Cotta
Custom colors are available
SEBS - White
SEBS+ Made-to-Order- White, Gray, Black, Dark Gray,
Base Coat Gray
Standard Colors - White, Gray, Tan, Black
Standard Special Order - Medium Bronze, Royal Brown, Dark
Gray, Sandstone,Terra Cotta
Custom colors are available
Drying Time to Re-Coat
12 Hours 4-6 Hours 2-4 Hours
% Solids by Volume
52% SEBS+: 45% SEBS: 44%
97%
Type
Water Based – must be installed above 40°F and cannot freeze. Drying time is prolonged in higher humidity. Not to be
installed when rain is imminent.
Solvent Based – high odor, VOC restricted in parts of the country. Not susceptible to freezing. Rain will not wash away or affect
proper cure of the coating.
Silicone (inorganic)-based, moisture-cure with low odor. Not susceptible to freezing, can be installed in low
temperatures.
Elongation & Tensile Strength
Excellent elongation (325%) but low tensile strength (270 psi) –
accommodates excessive movement but will not withstand increased foot trafic.
Excellent elongation (800%) and high tensile strength (1100 psi) – accommodates excessive movement, withstands increased
foot trafic.
Good elongation (235%) but medium tensile strength (478 psi) –
accommodates movement but will not withstand increased foot trafic.
Permeability
Permeable (breathable) – will let moisture vapor pass through product. Permeable coatings have poor resistance to algae
and fungi growth.
Non-permeable (non-breathable) – coating will not breathe and moisture trapped
below the coating will cause blistering over time. Low permeability provides excellent
resistance to algae and fungi growth.
Permeable (breathable) – will let moisture vapor pass through product. Permeable coatings have poor resistance to algae
and fungi growth.
Ponding Water
Not resilient to ponding water and will delaminate when applied over wet substrates. Since it is water based, re-emulsiication is possible during
prolonged ponding exposure.
Excellent in ponding water applications. Coating is solvent based and will not re-emulsify during prolonged ponding
exposure.
Touted as excellent in ponding water because it is not water based and will not re-emulsify in prolonged ponding. However, it is permeable and loss of adhesion is possible if the substrate
becomes wet.
VOC Low or no VOCHigh, strong odor, lammable; Cannot be
shipped to Southern CaliforniaLow or no VOC
PrimerA-125, a rust inhibiting primer required
over rusting metal surfaces.SEBS Primer is required over severe or solid
rust surfaces only.
Si 2-Part Epoxy Primer is required over asphalt roofs, aged PVC and Hypalon
roofs, rusted metal and areas of ponding water. Si TPO Primer is required over
TPO roofs.
Warranty
Commercial Metal Roof Projects Only: 5- or 10-year system warranties or
material warranties
Residential Roof Projects or Other Approved Substrates:
5- and 10-year material warranties
Commercial Metal Roof Projects Only: 10- or 15-year system warranties or material
warranties
Residential Metal Roof Projects Only:10- and 15-year material warranties
Commercial Roof Projects Only: 10, 15- or 20-year system warranties or
material warranties
Available over metal, concrete, aged PVC, aged Hypalon, EPDM, aged Mod
Bit, aged smooth BUR, aged TPO.
Asphalt StainingMust use different mixture to prevent
asphalt staining
Use SEBS+ Two coats are needed over asphalt
substrates. The irst may stain but the second coat will cover.
Must use Si 2-Part Epoxy Primer to prevent staining
Shelf Life 1 year
Tensile Strength The maximum stress the material will sustain before fracture. The tensile strength is calculated by dividing the maximum load by the original cross-sectional area of the test specimen.
Elongation The increase in the gauge length, measured after fracture of the specimen within the gauge length, usually expressed as a percentage of the original gauge length.
SILICONE ROOF COATING
With the Silicone Roof Coating System from Mule-Hide Products, contractors can offer an environmentally friendly restoration option with:
• Superior Resistance to Ponding Water • Same Day Recoating • Low Odor • Energy Savings • Years of Durable, Low-maintenance Seamless Protection • Cost Savings • Tax Relief Restore and repair the following roof types:
• EPDM • Asphalt • Aged TPO • Aged Modiied Bitumen
• Aged PVC • Concrete • Metal • Aged Hypalon
19
SILICONE ROOF COATING
20
Product Code Color Description Coverage Shelf Life
16MHSIRC1
White
1 Gallon Pail
1 Gallon Sq Ft 1 Year
16MHSIRC5 5 Gallon Pail
16MHSIRC55 55 Gallon Pail
16MHSIRC1G
Gray
1 Gallon Pail
16MHSIRC5G 5 Gallon Pail
16MHSIR55G 55 Gallon Pail
16MHSIRC5T Tan 5 Gallon Pail
16MHSIRC5B Black 5 Gallon Pail
SILICONE ROOF COATING Single part roof coating that creates a
barrier that is resistant to weathering,
is durable, breathable, watertight and
weatherproof.
Product Code Description Coverage Shelf Life
16MHSISC1 1 Gallon Pail
1 Gallon Sq Ft 1 Year16MHSISC5 5 Gallon Pail
16MHSISC55 55 Gallon Pail
SILICONE SKYLIGHT COATING A single part roof coating
manufactured from durable
inorganic silicone elastomers,
reinforcing pigments and silane
adhesions promoters. It is a
oxime neutral chemistry that is not
corrosive to metals.
Product Code Color Description Coverage Shelf Life
09MHSIGRGY Gray 5 Gallon Pail 15 lbs per
Sq Ft5 Years
09MHSIGRYW Yellow 5 Gallon Pail
WALKWAY GRANULES Colored EPDM granules specially
formulated to provide a non-slip surface
over a Mule-Hide Silicone Roof Coating.
Product Code Color Description Coverage Shelf Life
16MHSISECL Clear 1 tube (12/ctn)
See Product
Data Sheet1 Year
16MHSISEWH
White
1 tube (12/ctn)
16MHSISEA1 1 Gallon Pail
16MHSISEA3 3.5 Gallon Pail
SILICONE ROOF SEALANT Is a high solids non-shrinking moisture
cure silicone sealant that has minimal
odor, contains no solvents and has less
than 10 grams per liter VOC. Provides
excellent adhesion to concrete, masonry,
polyurethane foam, EPDM, TPO, aged
PVC, aged acrylic coatings, granular cap
sheet, wood, metals, Kynar® Finishes and
most other common building materials.
Mule-Hide Si TPO Primer is required for
TPO roof membranes.
Product Code Description Coverage Shelf Life
16MHSISOL1 1 Gallon PailN/A 2 Years
16MHSISOL5 5 Gallon Pail
SI CLEANING SOLVENT (For Equipment Clean-up) Is a high lash aromatic solvent that may be used to clean tools and equipment.
21
Product Code Description Coverage Shelf Life
16MHSIRC1 1 Gallon Pail 1 gallon per 800-1,000
Sq Ft 2 Years16MHSITPR5 5 Gallon Pail
SI TPO PRIMER Is a primer used to promote adhesion with
our Mule-Hide 100% Silicone Roof Coating
to new and aged TPO rooing membranes.
It is manufactured from a fast evaporating
solvent carries and adhesive resins. Primer
has a blue tint to allow applicator to better
guage application rates.
Product Code Description Coverage Shelf Life
16MHA1155 5 Gallon Pail 1/4-1/5 Gallon Sq Ft1 Year
16MHA11555 55 Gallon Drum
115 CLEANER Is a ready-to -use, environmentally friendly
cleaner that is excellent at removing dirt, oil,
and grease from a variety of surfaces.
Product Code Description Coverage Shelf Life
16MHSIEPK
Kit =
1 - 2.5 gal Pt. A
1 - 2.5 gal Pt. B
1/2 Gallon Sq Ft 1 Year
SI 2-PART EPOXY PRIMER KIT Is a water-based primer used to promote adhesion and prevent asphalt staining with our Mule-Hide 100% Silicone Roof Coating. Also used over areas of rusted metal to encapsulate rust.
TPO
TIETEX 325 & 272 POLY FABRIC Tietex 272 and Tietex 325 are 100% polyester stitch-bonded fabrics made without the use of adhesives. They provide outstanding physical strength, unique elongation, quick wet-out and saturation, and ease of application.
Product Code Description Weight
Tietex 325 Poly Fabric
09MHTT3043 1 roll - 4"X300' 1.5 lbs
09MHTT3063 1 roll - 6"X300' 3 lbs
09MHTT3123 1 roll - 12"X300' 6 lbs
09MHTT3203 1 roll - 20"X300' 11 lbs
09MHTT3403 1 roll - 40"X324' 22 lbs
Tietex 272 Poly Fabric
09MHTT2063 1 roll - 6"X300' 3 lbs
09MHTT2123 1 roll - 12"X300' 6 lbs
09MHTT2403 1 roll - 40"X324' 22 lbs
NOTES
22
ACRYLIC ROOF COATING
LASTING RESTORATION OR REPAIR KEEPS EXISTING ROOFS OPERATING EFFICIENTLY. Every year that a building owner can keep the existing roof operating eficiently, keeps money in their pocket. Comprising nearly one-third of operating costs, energy consumption is the single biggest expense to commercial building owners today. Investing in an energy eficient roof can reap substantial savings. • Energy Eficient Roofs • Compare the lifetime cost of re-rooing • Extends Roof Lifecycle • Easy to repair • Flexibility • Encapsulates Rust • Tax relief
23
A-200 FLASHING GRADE Highly lexible sealant for seams, penetrations, lashings, metal roof fasteners, and other areas to ill voids in the substrate. Application of product can be brushed or
extruded.
Product Code Description Coverage Shelf Life
16MHA2001 1 Gallon Pail
1-3 Gallons Sq Ft 1 Year16MHA2003 3.5 Gallon Pail
16MHA2005 5 Gallon Pail
Product Code Description Coverage Shelf Life
16MHA1155 5 Gallon Pail 1/4-1/2 Gallon Sq Ft1 Year
16MHA11555 55 Gallon Drum
115 CLEANER Is a ready-to -use, environmentally friendly
cleaner that is excellent at removing dirt, oil,
and grease from a variety of surfaces.
A-125 METAL ROOF PRIMER Zinc-rich, dark yellow color for easy to see
coverage. Improves adhesion of inish
coating while it encapsulates rust and inhibits
development of new rust. Apply by brush,
roller, or airless sprayer.
Product Code Description Coverage Shelf Life
16MHA1255 5 Gallon Pail
1/2 Gallon Sq Ft 1 Year16MHA12555 55 Gallon Drum
16MHA125TO 275 Gallon Tote
24
ACRYLIC ROOF COATING
A-300 BASE TPO (For Coating Aged TPO Membrane with Acrylics) An all-acrylic polymer based coating designed for improved adhesion to the surface of suitably cleaned, weathered (minimum 4 years) TPO (Thermoplastic PolyOlein) rooing membranes and lashings. When applied to a properly cleaned, weathered TPO roof, A-300 BASE TPO will provide a well bonded surface for the application of A-300 FINISH coat.
Product Code Description Coverage Shelf Life
16MHA3BT5 5 Gallon Pail
1.5 Gallons Sq Ft 1 Year16MHA3BT55 55 Drum
16MHA3BTTO 275 Tote
A-300 FINISH CRRC® rated and ENERGY STAR® listed highly elastomeric coating. Exceptional durability and UV stability extends roof life. Attractive bright white reduces energy consumption. Apply by brush, roller, or airless sprayer. *Additional colors available in 5 Gallon, 55 Drum and 275 Tote.
Product Code Description Coverage Shelf Life
16MHA3001 1 Gallon Pail
2 Gallons Sq Ft 1 Year16MHA3005 5 Gallon Pail
16MHA30055 55 Drum
16MHA300TO 275 Tote
A-301 SKYLIGHT FINISH Coats weathered skylight panels. Milky white in pail, it dries to a translucent, lexible ilm for a watertight seal that allows light to pass through.
Product Code Description Coverage Shelf Life
16MHA3011 1 Gallon Pail2 Gallons Sq Ft 1 Year
16MHA3015 5 Gallon Pail
9
A-320 FINISH (For use on Asphaltic Substrates) For coating over asphaltic substrates and where periodic ponded water occurs. CRRC® rated and ENERGY STAR® listed. Areas where ponded water remains for more than 48 hours may require the installation of new drains to provide proper drainage or tapered insulation and new, compatible rooing materials to create positive drainage to the existing drain system.
Product Code Description Coverage Shelf Life
16MHA3201 1 Gallon Pail
See Product Data Sheet 1 Year16MHA3205 5 Gallon Pail
16MHA32055 55 Drum
16MHA320TO 275 Tote
A-300 BASE For application to uncorroded metal, modiied bitumen, asphalt BUR, PVC, EPDM, Hypalon polyurethane foam and concrete roofs. A high degree of rubber-like elasticity allows this product to accommodate wide swings in temperature and signiicant building movement. A-300 Base will provide a well bonded surface for the application of A-300 FINISH coat.
Product Code Description Coverage Shelf Life
16MHA3BC5 5 Gallon Pail
1.5 Gallons Sq Ft 1 Year16MHA3BC55 55 Drum
16MHA3BCTO 275 Tote
25
NOTES
26
SEBS (Styrene Ethylene/Butylene Styrene) Roof Coating System is a solvent-based coating that is both tough and elastic. SEBS Roof Coating System is designed to be used primarily for repair and restoration of metal roofs but can be used over other systems.
• Ideal solutions for rusty roofs
• High elasticity conforms to building movement
• Ultra-low moisture permeability prevents corrosion
• High tensile strength withstands roof trafic
• Antioxidants and light stabilizers ensure durability
• Excellent adhesion to metal
SEBS ROOF COATING
27
SEBS ROOF COATING
SEBS BASE COAT Is an elastomeric solvent based coating intended for the repair and restoration of metal roofs. Use on barns, warehouses, metal trailers and shipping containers. Ultra-low moisture permeability prevents corrosion while high elasticity allows conformation to building movement.
Product Code Description Coverage Shelf Life
16MHSEB5G 5 Gallon Pail1.25-1.5 gallons / sq ft 1 Year
16MHSEB55G 55 Gallon Tote
SEBS ROOF COATING Is intended for the repair and restoration of metal roofs. Use on barns, warehouses, metal trailers and shipping containers. Ultra-low moisture permeability prevents corrosion while high elasticity allows conformation to building movement.
Product Code Description Coverage Shelf Life
16MHSER5W 5 Gallon Pail1.25-1.5 gallons / sq ft 1 Year
16MHSER55W 55 Gallon Tote
SEBS+ ROOF COATING Is intended for the repair and restoration of metal roofs. Use on barns, warehouses, metal trailers and shipping containers. Ultra-low moisture permeability prevents corrosion while high elasticity allows conformation to building movement.
Product Code Description Color Coverage Shelf Life
16MHSE1WH 1 Gallon (4/ctn) White
See Product
Data Sheet1 Year
16MHSE1BG 1 Gallon (4/ctn) Base Coat Gray
16MHSE1BK 1 Gallon (4/ctn) Black
16MHSE1DG 1 Gallon (4/ctn) Dark Gray
16MHSE1GY 1 Gallon (4/ctn) Gray
16MHSE5WH 5 Gallon White
16MHSE5BG 5 Gallon Base Coat Gray
16MHSE5BK 5 Gallon Black
16MHSE5DG 5 Gallon Dark Gray
16MHSE5GY 5 Gallon Gray
16MHSE55WH 55 Gallon White
16MHSE55BG 55 Gallon Base Coat Gray
16MHSE55BK 55 Gallon Black
16MHSE55DG 55 Gallon Dark Gray
16MHSE55GY 55 Gallon Gray
28
SEBS 1 Is a high-performance, multipurpose thermoplastic elastomer-based rooing sealant. Provides excellent adhesion to most surfaces including the list above. Use to seal seams, lashings and penetrations on all types of roofs. Ideal for rooing applications where appearance is important. *Refer to p.17 for color chart
Product Code Color Coverage Carton Shelf Life
30MHSEB1WH White
See Product
Data Sheet
(12) 10 oz
tubes/ctn1 Year
30MHSEB1BK Black
30MHSEB1GY Gray
30MHSEB1DG Dark Gray
30MHSEB1CY Clay
30MHSEB1SA Sandstone
30MHSEB1WT Wicker/Tan
30MHSEB1MB Medium Bronze
30MHSEB1MU Musket Brown
30MHSEB1RB Royal Brown
30MHSEB1BZ Bronze
30MHSEB1AL Aluminum
30MHSEB1PC Pure Clear
SEBS SEAM SEALER It is intended for lashing, sealing and repairing metal roofs and trailers.
Product Code Description Coverage Shelf Life
16MHSESS3 3 Gallon PailSee Product Data Sheet 1 Year
16MHSESS5 28oz can - 12/ctn
SEBS PRIMER Is intended for priming rusty roofs prior to application of SEBS Roof Coating and SEBS+ Roof Coatings. SEBS Primer is also ideal for coating rusty metal roof decks prior to installation of new rooing systems.
Product Code Description Coverage Shelf Life
16MHSEPR5 5 Gallon Pail1.25 gallon / sq ft 1 Year
16MHSEPR55 55 Gallon Tote
929
NOTES
30
Mule-Hide asphalt cements and coatings install quickly, easily and safely with consistent performance both
“On-the-Roof” & “Out-of-Pail”.
• Consistent Performance On-the-Roof & Out-of-the-Pail
• The Products You Need in the Sizes You Need
• Products That Apply Quickly, Easily, Safely
• Economical
• Extended Roof Life
ASPHALT CEMENTS & COATINGS
31
32
ASPHALT CEMENTS & COATINGS
102 FIBRATED ROOF COATING A iber reinforced, non-polymer modiied
asphalt roof coating that forms a lexible,
weather resistant ilm, that has excellent
adhesion to most surfaces.
Product Code Description Coverage Shelf Life
16MH1025 5 Gallon PailSee Product Data Sheet 2 Years
16MH10255 55 Gallon Drum
221 WET/DRY ROOF CEMENT A wet repair of roof leaks in many types of asphalt roof membranes. Its heavy “trowel-grade” consistency makes this product ideal for sealing and patching temporary emergency holes and cracks in roofs, even in standing water. Formulation is non-destructive to asphalt-based rooing materials.
Miami Dade County Approved. Meets ASTM D4586, D3409
Product Code Description Coverage Shelf Life
16MH2213 3 Gallon Pail8 Gallons Sq Ft 2 Years
16MH2215 5 Gallon Pail
211 PLASTIC CEMENT For use as a cold-applied sealing and repair material in many types of asphalt roof membranes. It has a heavy “trowel-grade” consistency which makes this product ideal for lashing details and a variety of waterprooing repairs, such as moving joints and roof penetrations. Has a superior formulation that will not separate. Miami Dade County Approved. Meets ASTM D4586
Product Code Description Coverage Shelf Life
16MH2113 3 Gallon Pail8 Gallons Sq Ft 2 Years
16MH2115 5 Gallon Pail
111 NON-FIBRATED ROOF COATING A professional grade, non-polymer modiied asphalt roof coating that forms a lexible, weather resistant ilm, that has excellent adhesion to most surfaces.
Product Code Description Coverage Shelf Life
16MH1115 5 Gallon Pail See Product Data Sheet 2 Years
231 FLASHING CEMENT For use as a cold-applied lashing cement in many types of asphalt roof membranes. Its heavy “trowel-grade” consistency makes this product ideal for lashing details and a variety of waterprooing repairs, such as moving joints and roof penetrations. Superior formulation will not separate.
Miami Dade County Approved. Meets ASTM D4586, D3409.
Product Code Description Coverage Shelf Life
16MH2313 3 Gallon Pail8 Gallons Sq Ft 2 Years
16MH2315 5 Gallon Pail
121 ASPHALT PRIMER A general purpose penetrating asphalt primer used to promote adhesion prior to the application of hot-mopped, cold-applied and self-adhesive membrane systems, as well as roof cements, mastics, and asphalt-based adhesives. Available in a 5 gallon pail or aerosol can Miami Dade County Approved. Meets ASTM D41
Product Code Description Coverage Shelf Life
16MH12114 15 oz can (12/crtn)1 Gallon Sq Ft 2 Years
16MH1215 5 Gallon Pail
33
241 PREMIUM MODIFIED FLASHING CEMENT Is a high quality formulation for use as a cold-applied bonding agent for SBS modiied bitumen roof system. Heavy, ‘trowel-grade’ consistency which makes it ideal for lashing details, attachment of membrane to steep slopes and parapet walls, and a variety of waterprooing repairs. Its lexibility and elasticity make it superior to standard plastic and lashing cements especially where there are moving joints. Miami Dade County Approved. Meets ASTM D4586, D3409.
Product Code Description Coverage Shelf Life
16MH2413 3 Gallon Pail8 Gallons
Sq Ft2 Years
16MH2415 5 Gallon Pail
251 PREMIUM WET/DRY ELASTOMERIC FLASHING CEMENT Is a high quality formulation for wet repair of roof leaks in many types of asphalt roof membranes and SBS rooing systems. This product is ideal for sealing and patching temporary emergency holes and cracks in roofs, even in standing water. Can be used for emergency repairs on shingles, BUR (Built-up Rooing), concrete,
and general damp prooing.
Miami Dade County Approved. Meets ASTM D4586,
D3409.
Product Code Description Coverage Shelf Life
16MH25111 10.5 oz Tube8 Gallons
Sq Ft2 Years16MH2513 3 Gallon Pail
16MH2515 5 Gallon Pail
311 NON-FIBRATED EMULSION ROOF COATING Is an asphalt-based, clay emulsion roof coating that can be used as a protective coating over smooth surfaced asphalt built-up and modiied bitumen membranes. Can also be used as a base coat for relective coatings. This product does not low when applied in thick coatings. After drying, stays in place even when exposed to elevated temperatures. Miami Dade County Approved. Meets ASTM D1227 Type III Class I.
Product Code Description Coverage Shelf Life
16MH3115 5 Gallon PailSee Product Data Sheet 18 Months
16MH31155 55 Gallon Drum
401 PREMIUM FIBRATED ALUMINUM ROOF COATING Provides premium, high-
performance protection for asphalt-based
roofs. It is a heavy bodied formulation with
special reinforcing ibers that “push” the
aluminum lakes to the surface for long
lasting relectivity and greater durability. In
addition, this formula is non-destructive to
asphalt-based rooing membranes.
Miami Dade County Approved. Meets ASTM D2824
Type III.
Product Code Description Coverage Shelf Life
16MH4015 5 Gallon PailSee Product Data Sheet 2 Years
16MH40155 55 Gallon Drum
301 FIBRATED EMULSION ROOF
COATING Is an asphalt-based, clay emulsion roof coating. Superior formulation provides increased weather resistance and durability. This product does not low when applied in thick coatings and when dry, will stay in place even when exposed to elevated temperatures. In addition, the solvent free formulations are water based and non-combustible, requiring no “red tag” labeling for ire hazard.
Miami Dade County Approved. Meets ASTM D1227
Type III Class I.
Product Code Description Coverage Shelf Life
16MH3015 5 Gallon Pail
See Product Data Sheet 18 Months16MH30155 55 Gallon Drum
406 STANDARD FIBRATED ALUMINUM ROOF COATING Provides high performance protection for asphalt-based roofs. It is a heavy bodied formulation with special reinforcing ibers that “push” the aluminum lakes to the surface for long lasting relectivity and greater durability. In addition, this formula is non-destructive to asphalt-based rooing membranes.
Miami Dade County Approved. Meets ASTM D2824
Type III.
Product Code Description Coverage Shelf Life
16MH4065 5 Gallon Pail
See Product Data Sheet 2 Years16MH40655 55 Gallon Drum
ASPHALT CEMENTS & COATINGS
34
410 PREMIUM NON-FIBRATED ALUMINUM ROOF COATING Provides premium, high-performance protection for asphalt-based roofs. It is easier to spread and provides greater coverage, though it weathers more rapidly. This formula is non-destructive to asphalt-based rooing membranes. Miami Dade County Approved. Meets ASTM D2824 Type I.
Product Code Description Coverage Shelf Life
16MH4105 5 Gallon PailSee Product Data Sheet 2 Years
16MH41055 55 Gallon Drum
416 STANDARD NON-FIBRATED ALUMINUM ROOF COATING Provides
high-performance protection for asphalt-
based roofs. It is easier to spread and
provides greater coverage, though it
weathers more rapidly. This formula is
non-destructive to asphalt-based rooing
membranes.
Miami Dade County Approved. Meets ASTM D2824
Type I.
Product Code Description Coverage Shelf Life
16MH4165 5 Gallon PailSee Product Data Sheet 2 Years
16MH41655 55 Gallon Drum
420 MOD BIT ADHESIVE - BGis a select formulation for use as a cold-applied bonding agent for SBS modiied bitumen base sheets and SBS modiied bitumen cap sheets.
Miami Dade County Approved. Meets ASTM D3019.
Product Code Description Coverage Shelf Life
16MH4205 5 Gallon Pail 1-1.5 Gallons Sq Ft 18 Months
421 MOD BIT ADHESIVE - Trowel Grade is a high quality formulation for use as a cold-applied bonding agent for SBS modiied bitumen roof systems. Heavy, “trowel-grade” consistency makes this product ideal for lashing details, attachment of membrane to steep slopes and parapet walls and a variety of waterprooing repairs, especially at moving joints where its lexibility and elasticity make it superior to standard plastic cements. In addition, the formulation is non-destructive to asphalt based rooing membranes.
Miami Dade County Approved. Meets ASTM D4586,
D3409.Product Code Description Coverage Shelf Life
16MH4213 3 Gallon Pail1-1.5 Gallons Sq Ft 2 Years
16MH4215 5 Gallon Pail
271 MOD BIT SEALANT Is a ibrated, cartridge grade, rubberized adhesive with bonding strength designed speciically for use with modiied bituminous products. It sets by loss of solvent content through evaporation. Because of its ease of application and vertical bonding strength, it is recommended for membrane seaming, lashing and detail work. Also has excellent low temperature lexibility. Miami Dade County Approved. Meets ASTM D4598, D3409.
Product Code Description Coverage Shelf Life
16MH27111 10.3 oz tube See Product Data Sheet 2 Years
35
SEALFAST TAPES & PRODUCTS
SEAL-FAST® TAPES may be used on a wide variety of surfaces including dificult roof materials such as : EPDM, TPO, most PVC, CSPE/Hypalon, CPE, SBS, APP modiied, asphalt BURs, coal tar BURs, all metal roofs, tiles, shingle, aluminum, galvanized steel, gypsum board, wood, polyethylene, propylene, polystyrene, iberglass, brick, concrete, masonry, OSB, etc.. This product may be used to repair gutters, chimney lashings, and metal roofs on mobile homes and transport vehicles. Seal-Fast® Tape makes a permanent watertight seal. Can be installed in temperatures down to -20oF (with our Seal-Fast® Primer). Also available in Seal-Fast Plus, Aluminum, Double Stick and Fabric tapes.
SEALFAST TAPE AND PRODUCTS
.035 SEAL-FAST TAPE May be used on a wide variety of surfaces
including dificult roof materials. This product
may be used to repair gutters, chimney
lashings, and metal roofs on mobile homes
and transport vehicles. Seal-Fast® Tape
makes a permanent watertight seal.
Product Code Color Description Carton Weight Shelf Life
08MHSF250W
White
2" X 50' 12/ctn
24 lbs 1 year
08MHSFT35W 3" X 50' 8/ctn
08MHSFT45W 4" X 50' 6/ctn
08MHSFT62W 6" X 25' 6/ctn
08MHSFT65W 6" X 50' 4/ctn
08MHSFT85W 8" X 50' 3/ctn
08MHSFT25W 12" X 50' 2/ctn
08MHSF245W 24" X 50' 1/ctn
08MHSF250G
Gray
2" X 50' 12/ctn
08MHSFT45G 4" X 50' 6/ctn
08MHSFT65G 6" X 50' 4/ctn
08MHSFT85G 8" X 50' 3/ctn
08MHSFT25G 12" X 50' 2/ctn
08MHSF245G 24" X 50' 1/ctn
08MHSF250B
Black
2" X 50' 12/ctn
08MHSFT35B 3" X 50' 8/ctn
08MHSFT45B 4" X 50' 6/ctn
08MHSFT65B 6" X 50' 4/ctn
08MHSFT85B 8" X 50' 3/ctn
08MHSFT22B 12" X 25' 3/ctn
08MHSFT25B 12" X 50' 2/ctn
08MHSF245B 24" X 50' 1/ctn
SEAL-FAST FABRIC TAPE - WHITE This product may be used to repair gutters,
chimney lashings, metal roofs on mobile
homes and transport vehicles. Seal-Fast®
Fabric Tape makes a permanent watertight
seal.
Product Code Description Carton Weight Shelf Life
08MHSFF250 2" X 50' 12/ctn
24 lbs 1 year
08MHSFF45W 4" X 50' 6/ctn
08MHSFF62W 6" X 25' 6/ctn
08MHSFF65W 6" X 50' 4/ctn
08MHSFF85W 8" X 50' 3/ctn
08MHSFF25W 12" X 50' 2/ctn
08MHSFF24W 24" X 50' 1/ctn
.065 SEAL-FAST TAPE PLUS This product may be used to repair gutters,
chimney lashings, and metal roofs on mobile
homes and transport vehicles. Seal-Fast®
Tape Plus makes a permanent watertight seal.
Product Code Color Description Carton Weight Shelf Life
08MHSFP42BBlack
4"x25' 6/ctn
24 lbs 1 year08MHSFP62B 6"x25' 4/ctn
08MHSFP42WWhite
4"x25' 6/ctn
08MHSFP62W 6"x25' 4/ctn
SEAL-FAST TEMPORARY LOW-SLOPE
ROOF SEALER Can immediately seal a roof leak when weather
is not permitting for a permanent repair.
Product Code Description Carton Weight Shelf Life
16MHSFE25 25 Pound Jug 2 per 50 lbs. 9 months
36
SEAL-FAST DOUBLE STICK TAPE Used to create a water-tight, conformable
seal or weather proof bond between two
surfaces. Use as a lap seal, under the foot of
an equipment curb or skylight. Can be rolled
into a bead or ball to form a gasket, seal a
gap or seal, as needed.
Product Code Description Carton Weight Shelf Life
08MHSFD150 1" X 50' 24/ctn
24 lbs 1 year08MHSFD250 2" X 50' 12/ctn
08MHSFD350 3" X 50' 8/ctn
SEAL-FAST ALUMINUM TAPE as a protective coating for surfaces where
abrasion and corrosion resistance is required.
The Seal-Fast®Aluminum Tape seals to itself
so that it can be cut and folded around an
object.
Product Code Description Carton Weight Shelf Life
08MHSF250A 2" X 50' 12/ctn
24 lbs 1 year08MHSFT45A 4" X 50' 6/ctn
08MHSFT65A 6" X 50' 4/ctn
SEAL-FAST CLEANER Removes grease, oil, oxidations and other
contaminates from roof surfaces prior to the
application of Seal-Fast® Tapes. Mule-Hide
Seal-Fast® Spray Cleaner leaves no residue,
dries fast, and is non chlorinating so it is
environmentally friendly and legal in all states.
Product Code Description Carton Weight Shelf Life
16MHSFC14 14 oz 12/ctn 12 lbs 1 year
SEAL-FAST PRIMER Used to ensure proper adhesion when
installing Seal-Fast® Tape or Seal-Fast® Fabric
Tape in temperatures below 40°F or when
the surface quality is questionable. Seal-Fast®
Primer is also used on mortar, porous surfaces
and granulated surfaces (granules must be
removed).
Available in a quart can or aerosol can
Product Code Description Carton Weight Shelf Life
16MHSFP1Q quart 12/ctn 24 lbs 1 year
16MHSFP14 14 oz can 12/ctn 6 lbs 1 year
37
WATERPROOFING
38
Product Code Color Description Coverage Shelf Life
16MHSIMC1
White
1 Gallon Pail
1-2 Gallons
Sq Ft1 Year
16MHSIMC5 5 Gallon Pail
16MHSIMC55 55 Gallon Pail
16MHSIMC5GGray
5 Gallon Pail
16MHSIM55G 55 Gallon Pail
16MHSIMC5T Tan 5 Gallon Pail
16MHSIMC5B Black 5 Gallon Pail
16MHSIM5CL Clear 5 Gallon Pail
SILICONE MASONRY WALL COATING Is a single component wall coating that
creates a durable, breathable, watertight
barrier that is resistant to natural weathering.
100% Silicone Masonry Wall Coating is also
grafiti resistant and will not allow adhesion
of most types of water and solvent based
paints. It is manufactured from durable
inorganic silicone elastomers, reinforcing
and relective pigments and silane adhesion
promoters.
A-400-W MASONRY WALL COATING Formulated to provide a lexible, waterprooing, liquid-applied membrane for exterior masonry surfaces.
Product Code Description Coverage Shelf Life
16MH400W5 5 Gallon Pail1 Gallon Sq Ft 1 Year
16MH400W55 55 Drum
MORTAR SENTRY Designed for use on brick, mortar, concrete block, cultured stone, sandstone and concrete. It is not recommended for use on non-silicate natural stone such as limestone or dolomite. Mortar Sentry is a silane/siloxane based waterprooing treatment consisting of two products. Mortar Sentry Water Seal 10 is a 10% active solution and is recommended for vertical surfaces. Mortar Sentry Water Seal 15 is a 15% active solution and is recommended for horizontal surfaces.
Product Code Description Coverage Shelf Life
16MHMSW101 1 Gallon Pail
See Product Data
Sheet1 Year
16MHMSW105 5 Gallon Pail
16MHMSW151 1 Gallon Pail
16MHMSW155 5 Gallon Pail
Treated with Mortar Sentry vs non-treated
Treated Non-Treated
MP LIQUID SEALANT A 100% solids, non-shrink, one-
part polyurethane pourable sealer
can be used with metal roof seams
and fasteners, gutters, damaged
polyurethane foam and roof projections
on PVC, EPDM, primed TPO, primed
Mod Bit and primed BUR rooing
systems.
Product Code Description Carton Shelf Life
08MHMPLS2W White
4 pouches per 1 Year08MHMPLS2B Black
08MHMPLS2G Gray
ACCESSORIES
39
SHAPESHIFT PITCH PAN Consist of straight and outside corner
sections snap together to create an
endless number of pitch pan sizes to seal
around roof projections. The pieces snap
together with interlocking joints.
Product Code Description Carton Weight
08MHSSPC48 Corners 48 per 6 lbs.
08MHSSPC16 Corners 16 per 2 lbs.
08MHSSPS16 Straights 16 per 2 lbs.
TPO
SEAM PROBE Seam Probe is a hand tool used to check
the integrity of heat welded seams on
heat welded rooing systems. The probe
has a heat-treated tip and the handle is
tapped to it standard threaded extension
handles allowing the tool to be used from
the standing position
Product Code Description Carton Weight
08MHSMPRB White 1 per 2 lbs.
Customer Line: 800-786-1492 • www.mulehide.comCheck our website monthly for the latest updates & technical bulletins.National Support Center • 1195 Prince Hall Drive • Beloit, WI 53511 tel. 608.365.3111 • fax. 608.365.7852
The information herein should not be considered all-inclusive and should always be accompanied by a review of the Mule-Hide specifications and guidelines and good application practices.
This information herein is based upon data and knowledge considered to be true and accurate at the time of printing and is provided for the reader’s consideration, investigation and verification. No statement made by anyone may supersede this information, except when done in writing by Mule-Hide Products Co., Inc. Mule-Hide Products Co., Inc. does not warrant any results to be obtained. Statements concerning possible use of Mule-Hide products are made without knowledge of your particular roof and such an application may not be fit for your particular purpose. MULE-HIDE DISCLAIMS ALL WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, except written warranties attached to Mule-Hide products and written warranties signed by an officer of Mule-Hide.
Visit the Mule-Hide website at www.mulehide.com prior to any installation for updated technical specifications and details. Mule-Hide is a U.S. registered trademark. DensDeck is wholly owned registered trademark of Georgia-Pacific Gypsum LLC/Georgia-Pacific Wood Products LLC. SECUROCK is wholly owned registered trademark of USG Corporation. Kynar is wholly owned registered trademark of Arkema Inc. Elvaloy is wholly owned registered trademark of E. I. du Pont de Nemours and Company or its affiliates. All rights reserved.
©2015 Mule-Hide Products Co., Inc. • Printed in USA • MH LIT# LT.BROMR• Rev. 1 05/18
40