MAGSEAL8 Magnetic seal Pack 8mm Corner Entry V04.09.2014...magnet seal pack,to form 8mm v04/09/2014...
Transcript of MAGSEAL8 Magnetic seal Pack 8mm Corner Entry V04.09.2014...magnet seal pack,to form 8mm v04/09/2014...
MAGNET SEAL PACK,TO FORM 8MM
V04/09/2014
ASSEMBLY INSTRUCTIONS
CORNER ENTRY ENCLOSUREHINGED
T HESE INSTRUCTION REPLACE THE SET SUPPLIED
W ITH THE SHOWER DOORS.
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Addition notes
Please inspect this product upon delivery. any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage of defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS-AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note--alumimium is a soft metal, and undergoes a series of extrusion.
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
TOOLS REQUIRED
This product is heavy and may require two people to install.
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Hammer
Silicone Sealant
1
ASSEMBLY INSTRUCTIONS-DRAWING
2
(1)
(2)
(3)
(4)(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15) (16) (17) (18)(19)
(20)
(1) 2. x Wall Bracket
(2) 2. x Cover Cap (Wall Post A)
(3) 2. x Cover Cap (Vertical Profile)
(4) 2. x Wall Post
(5) 2. x Vertical Profile
(6) .
(7)
2
.
x Vertical Seal
(8) .
(9)
2
.
x Moving Door
(10).
8x Wall Plugs
8x Screws 4x30mm
2x Handle
(11) .
(12) .
(13) .
(14) .
(15) .
(16) .
(17) .
(18)
6
.
x Screw Cover caps
(19)
(20)
6
.
.
x Screws 4x12mm
6x Screw Cover Cap Washers
2x Top Hinge2x Bottom Hinge
2x Curved End Cover Cap
(LH+RH)
2x Bottom Seal
2x Drip Strip
1x End Cover Cap
2x Magnet Seal (Moving Door)
3
ASSEMBLY INSTRUCTIONSIf you require help, we advise you firstly contact a competent plumberInstallation Steps
Step 1THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
20
20 20
760/800/900760/800/900
1020
10
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER PANEL / DOOR,
Step 2
Step 3
6mm
4x30
x4
x4
x4
x4
4
20
MOVING DOORFIXED PANEL
Step 4
Step 5
5
INSIDE VIEW INSIDE VIEW
MOVING DOOR
FIXED PANEL
Step 6
Step 7
6
INSIDE VIEW INSIDE VIEW
x6
x6
x6
3.0mm
Step 8
Step 9
INSIDE VIEW
!
!
How to adjust the width of the
hinged door
Minimum 10mm internal overlap required
Glass panel
Glass panel
Vertical profile
Vertical profile
Wall profile
Wall profile
Wall
Wall
Maximum adjustment
Minimum adjustment
7
Sil icone
Sil i
cone
Silicone (outside edge only) where the vertical profiles meet the wall, and the
glass panels meet the tray.
6mm
x2
x2
x2
Step 10
Step 11
8
CARE AND MAINTENANCE
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
COMMITMENT TO QUALITY
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact out customer services quoting
the following:
Product name: 8mm Hinged Corner door
Customer help line number:0344 804 48 48
Product code: MAGSEAL8
9
INSTALLERS NOTES
10
/2014612
/14
Shower enclosures with aluminium profiles and safety glass
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.