M9000 SERIES IN-GRADE LIGHTING · The M9000 has a range of32Watts to400Watts in a variety of lamp...

M9000 SERIESIN-GRADE LIGHTING

The Hydrel M9000 The Best Solution to In-grade Lighting

M9000 Series Three sizes cover a wide range ofin-grade lighting applications.

The versatility of the M9000 Series makes it perfect forilluminating everything from hightraffic pedestrian areas to grovesof tall trees.

Soft, even lightpenetrates to the top

branches of thismajestic oak.

A single M9000Series wall washplaced under an

open structured treecan effectively

highlight the highestoutermost foliage

without hot spots.

1

A row of M9400 Series with 70Wattmetal halide lamps illuminates patioseating and surrounding shrubberyat a college art gallery. Low lenstemperatures and rugged constructionare key M9400 Series attributes.

At the exclusive Venetian Hotel in Las Vegas M9400s,M9700s, and M9800s are employed to illuminate avariety of statues, columns, and arches. Spots are thedistribution of choice with 70 Watt metal halide in theM9400s and 100 Watt metal halide in the M9700s.

Safety First !Low surfacetemperaturesgenerated byM9000 double lensmodels make themideal for safelylighting areas withhigh pedestrianactivity.

A series of M9700100 Watt metalhalide fixtures

illuminate a row ofpanels in a park.

Medium spotdistribution, low

profiles, and coollens temperatures

are required.

This county courthouse uses M9700s with175Watt metal halide wall wash on the buildingsand 100 Watt metal halide floods on the trees.

Support columns and arches at this Californiaretail center are lighted with100 Watt metalhalide fixtures with spot distribution. High pedestrian traffic requires low profileunits with low lens temperatures.

Hydrel was chosen as the preferred in-gradefixture because of its advanced aiming capabilities, low lens temperatures, and pleasing aesthetics.

M9000 Seriesdouble lens

models providean insulating layer

of air foradditional cooling.

Door

Lens

Door

Pin (keys intoSupportRing)

LensLampModule

ModuleSupportRing(rotates &locks)

LampModule

Lens

Lens

Tilt Ring(holds

module )

SwivelRing

( rotates& locks )

TiltSetting( locks)

Key(fits intomodulesupportring)

Rough-in-Section

The M9000 Series singlelens models offer highlighting efficiency withsimple, optical aiming.

Rough-in-Section

Double Lens Technology The M9000Series double lens models provide aninsulating layer of air for additional cooling.When the potential exists for direct humancontact with lenses, care is required to protectpedestrians from injury. The M9000 SeriesDouble Lens models ensure lower surface

temperatures by usingtwo separate lenseswith cool air circulatingbetween them.

Double lens technology - upper lens is cooled by aninsulating layer of aircirculating between thetwo lenses.

M9000 Series - Best for a Reason

Convective Cooling Conventional sealed fixtures depend onlyupon conduction and radiation for cooling. The 9000Series with itsvented doors pioneered convection cooling as well.

The M9000Series improves on theconvective cooling process by addingair-flow channels in the wall of therough-in section. Air-flow channels greatlyimprove ambient air circulation around thepower and lamp modules, delivering coolair deep into the rough-in section. Whencool ambient air draws heat from themodules, the warmed air escapes throughdoor vents at the top of the rough-insection.

Typically, M9000s operate 30° to40° coolerthan competitive products.

Cool Operation / Cool LensA major challenge in the design of in-grade fixtures is the removal ofheat to protect components and provide lower lens temperatures.

Patented Modular Flo-Thru Technology

The chimney effect - Rising warm air escaping out the door vents draws cool airdown air-flow channels in the rough-in section.

VENTEDDOOR

AIR FLOWCHANNEL

COOLAIR

WARM AIR

Today’s M9000Series is the result of constant improvement and refinement of the original9000Series. Below, several reasons why the M9000 Series is an industry standard.

Single lens lamp module Double lens lamp module

Modules withinthe rough-insection areimpervious tomoisture.

2

Hydrel’s M9000Series are the only in-grade lightsnot dependent upon sealing the outer housing toprotect lighting components inside.

M9000 lighting component modules are so impervious to water that it’sunnecessary to seal the rough-in section. Lens doors on all M9000s areeasy to open and close, never need sealing, and are vented for air coolingwithin the container. The lamp module lifts out and unplugs -relampoffsite, away from the dirt. Installation and maintenance become simplertasks.

Modular - M9000lighting components

are self-containedwatertight modules.

Flo-thru - in groundcontainers (rough-in

sections) are designed tolet water flow through

and run out the bottom.

Mechanical components are keyed,allowing maintenance and relamping to beaccomplished without reaiming.

Single lens, optically aimed.

Double lens, mechanically andoptically aimed.

Spread lens flattens distributionpattern. Dash line indicates beamwithout spread lens.

Easy AimingThe M9000Series refines both the mechanical and optical aimingprocess. Keyed components allow maintenance and relamping tobe accomplished without reaiming.

Fixture aiming is a critical element to many projects and designers are concernedwith the methods to accomplish it. The original 9000Series combined optical andmechanical aiming. The new M9000 refines the process by introducing an aimablemodule along with keyed components to lock-in or reproduce settings.

The original 9000Series offered simple aiming by the use of active lenses (opticalaiming) and module rotation. In addition to the standard rotational indexing andlocking feature, the new M9000Series offers the option of aiming the lamp moduleitself with a locking tilt mechanism. The lamp module is located below a secondsealed lens in the rough-in section.

In summary, the M9000 Series offers two lockable aiming options:

• Optically Aimed – active lenses and lamp module rotation

• Mechanically Aimed – lamp module tilting and lamp module rotation

Both options include Aim-Lock® indexed and locking components to allowrelamping and maintenance without reaiming.

A double lens M9420, mechanically aimedfixture uses a 360° keyed swivel ring and asingle surface tilt adjustment to aim the fixture.No lamp module entrance is required for aimingany M9000 Series fixture.

M9000 Series specificationsheets are available at our web site:http://www.hydrel.com

Rugged Construction/Superior Drive-over CapabilityThe M9000Series incorporates the best materialsavailable for each function. Lamp modules are constructed of high grade stainless steel andcovered with a high emissivity coating. Lenses are tempered

borosilicate glass for toughness and clarity.Ballasts and transformers are encapsulated ina heat dissipating epoxy withstrengthened ribs. Non-corrosive polymericjunction boxes are molded in place fortrouble-free operation.

Rugged materials andconstruction for superior drive-over capability.Rough-in sections use strong, heat resistantpolymeric material. Lamp module supportrings allow for drive-over strength in excessof normal auto, truck, and tractor weightrequirements.

Modular support ringand computer-designedstructural layout providestrength exceeding thatrequired for drive-overapplications.

Wide RangeAt 400Watts HID, the M9000 is the mostpowerful in-grade light in the industry.The M9000 has a range of 32Watts to400Watts in avariety of lamp types from fluorescent to HID. Thelargest of the M9000 Family, the M9800 Series, isthe only in-grade fixture in the industry toaccept mogul and E40 base 400Watt HIDlamps. As the most powerful in-grade light ever,the M9800 Series provides a new alternative for

floodlightingarchitecturalstructures with in-gradeconcealment.

A single M9800wallwash floodsan eighty footwide, eight-storyhigh wall.

3

4

M9000Series - A Family of In-grade Performers

At just 9 inches in diameter, theM9400 is the smallest in-grademodular fixture accepting colorcorrected metal halide lamps.

Up to70W, MH in spot, flood, and wallwash distributions. With a footprint only9 inches (230mm) in diameter.

The M9400 IP67

70Watts, 9”Diameter

M9000SeriesThe M9000 Series is an advanced versionof the original9000 Series introduced byHydrel in1990. Below is a brief overviewof its features and benefits.

* See page 8 for a more complete story of Modular / Flo-thru. Design and other original Hydrel 9000Series innovations.

The M9400 offers a unique rough-in section thatincludes an integral power supply compartmentin an “L” configuration designed to accommodateencapsulated power supplies for color correctedmetal halide lamps.

• Patented Modular / Flo-thru Design*exclusive to Hydrel Hydrel’s M9000 is the only in-grade line that does not require resealing at ground level. The patented modular design provides a removable module which can be relamped in a dry, controlled atmosphere.

• Increased Range - A family of three in-grade lights, 9 to18 inches in diameter, with lighting capacities spanning 32 to 400Watts.

• Cooler Operating - Convection cooling is made possible by air circulation within the container.30°- 40° cooler operation is achieved through improved convective cooling and the double lens option.

• Highest IP Rating - Hydrel offers the highest protection against moisture intrusion in the industry.

• Simpler Installation - Pre-installed rough-in sections, plug together modules, and a two-fastener locking door make installation 50% faster.

• Easy Maintenance - Lamp modules are easily removable to off-site locations for relamping and thereby are easily purged of moist air to end condensation problems.

• Easy Aiming - Indexed and locked components allow relamping without reaiming. Aim mechanicallyand optically without entering the lamp module.

• Architectural Aesthetics - Smaller footprint and more door choices.

• Rugged Construction - Improved design and materials to surpass drive-over requirements.

9229

9229

15.9405

9229

9229

12.2310 14.4

365

19.4494

19.4494

A cylindrical rough-insection accepts lamps up to32 Watt fluorescent or up to75 Watt incandescent andquartz for wall wash, spot,and flood applications.

Please refer to page18 for M9400 ordering information.

5

The workhorse of the group, thepopularsized M9700 features a wide variety ofdistributions with internal glare controland filtering plus an assortment of safetyand light control accessories.

Up to175W, MH in spot, flood, and wallwashdistributions with a12 inch (305mm)diameterfootprint.

The M9700 IP68

175Watts, 12”Diameter

The M9800 is the only in-grade fixture to acceptmogul and E40 based 400 Watt HID lamps.

Up to 400W, MH, HPS in spot, flood, and wall washdistributions, with an18 inch (460mm) footprint.

The M9800 IP67400Watts, 18”Diameter

The mid-size M9700 HID with keyed modularcomponents: door, rough-in section, lampmodule, and power supply.

The M9700 covers the midrange of this versatile familyof in-grade lights and promises to be the most versatile.Rated at 175 Watt maximum HID, it will handle a widerange of lighting tasks.

The M9800 accepts mogul and E40 based lamps to 400 Wattsfor wall wash, spot, and flood applications. It opens the door tonew options for floodlighting architectural structures by greatlyreducing the visibility of the fixture, an aspect often objectionableto designers.

12305

12305

20508

12305

12305

16407

27.5700

18460

16.7425

18460

Please refer to page19 for M9700 ordering information.Please refer to page 20 forM9800 ordering information.

6

M9000 Series – Wide Range Performance Test lighting on an eight-story wall (below),demonstrates the wide range ofM9000Series capabilities ranging from32Watts fluorescent to400Watts HID.

A 9 inch (230mm) footprint M9420,MH70 tight spot, provides highillumination from a low wattage fixturewith excellent color for a variety ofapplications.

The M9410, FL32 fluorescent,medium flood is an efficientfixture for rows of bushes, smalllandscapes, and multiple smallarchitectural features.

A single M9810, MH400 wall wash illuminates a fulleight-story wall 80 feet (25m) wide. Setback is less than6 feet (2m). Excellent for large buildings and wallillumination.

An M9810, MH400tight spot pattern on

an eight-story wall( this configuration is

capable of illuminatingto15 stories).

7

The M9400 Series is ideal forsmall landscapes, rows of smalltrees or shrubs, and smallarchitectural features.

The low surface temperature generated in a doublelens M9700 or M9800 using a100Watt HID lampmakes it an excellent option for an area high inpedestrian activity.

Above, M9700s equipped with 70Watt HPS lamps inwide flood distribution illuminate the sandstonefacades of the famous Royal and Ancient Golf Club atSt Andrews, Scotland. These Hydrel double lensluminaires were chosen for their low lens temperatureand excellent pedestrian protection capabilities.

8

Hydrel In-grade Lighting

UNDERWATER LIGHTING TECHNOLOGYMost in-grade fixtures depend upon a watertight shell toprotect vulnerable lighting components within. Keepingwater out is a formidable task, especially when the shellhas to be accessed regularly for maintenance. Moisturewithin the shell means disaster when corrosionattacks electrical components.

Hydrel solved the moisture problem by drawing on itsnearly forty-year experience in underwater lighting. Anew kind of in-grade fixture was conceived – the M9000Series, based on underwater lighting technology.

IMPROVED PHOTOMETRICSSmaller more efficient lamps combine with an array of precision reflectors andoptically active lenses. The M9000Series reaches photometric performancelevels never before achieved by in-grade lighting fixtures.

A trio of Hydrel underwater lights

Underwater modular designapplied to in-grade lightingwas truly a radical approach in1990. But to Hydrel engineerssuch underwater lightingtechniques were anything butradical. At Hydrel they werethoroughly tested, reliable,everyday procedures.

UNDERWATER DESIGN AND THE MODULAR CONCEPTSealed lighting components, similar to those used in pools and fountains,inspired the idea behind the M9000 in-grade light. A polymeric, non-corroding,in-grade container features a built-in watertight junction box, sealedwatertight lamp module, and an epoxy-encapsulated watertight power supplymodule, all linked by plug-together underwater-rated cables and connectors. Everything within the container is watertight!

MODULAR DESIGN AND THE FLOW-THRU CONCEPTOnce the lighting component modules are totally watertight, a watertight shell to protect them is no longer necessary. Flow-thru design means that no attempt is made to keep water out ofthe container. If water runs in, it flows through to drain out the bottom, or simply evaporates.

Even today, Hydrel M9000Series are the only in-grade fixtures that do not depend on awatertight shell to protect lighting components.

How the unique and innovative 9000 Series in-grade lights came into being.Why they remain unmatched even today!

In 1990, Hydrel revolutionized in-grade lighting design bycombining underwater lighting technology and modular

design to create flow-thru, in-grade containers featuring easilyremoved, sealed lamp modulesand newly developed smallefficient lamps – thus launching acutting edge series of in-gradelights: the celebrated 9000 Series.

Underwater testing

An early Model 9000 operates while totally submerged in water.Patented encapsulation technology employing Hydreseal™– aheat dissipating resin, and time tested sealing methods, preventmoisture from penetrating lighting components.

An early Model9000 cut-awaydemonstratesthe innovativeconcept of aflo-thru rough-in sectionholdingwatertightlightingcomponentmodules.

Low temperature testing

An early Model 9000HID operates completely

encased in ice. Thefreezing and thawing

process producestremendous pressures

on in-grade fixtures.

Watertight moduleswithin the rough-insection are imperviousto moisture.

Sealed Acralume™

lamp modules,developed speciallyfor the original 9000Series, contributedastonishing newphotometricperformance.

9

Cooler OperationVented door allows air toflow into the rough-in sectionto cool the sealed modularlighting components. Otherin-grade fixtures must betightly sealed and cannottake advantage of cool airventilation.

Rough-in SectionA major development withflow-thru technology is therough-in section. The ruggedcorrosion-resistant section canbe set in place duringconstruction and await finalinstallation of sensitive lightingcomponents.

Double Lens TechnologyDouble lens models provide aninsulating layer of air for additionalcooling. Two separate lenses withcool air circulating between themensure lower surface temperatures.

Significant Hydrel Innovations

Lamp Module / Goodbye CondensationRelamp at your work station, notout on site, in the dirt. The sealedlamp housing can easily be takenfrom the container to a clean,accessible area for relamping ormaintenance. High-performanceseals and dry air purgingeliminate condensation.

Easy Aiming and Aim-Lock™ TechnologyUse both mechanical andoptical aiming techniques foraiming versatility. Aim-Lock™

technology featurescomponents indexed andlocked to allow relamping andmaintenance without reaiming.

Light Where You Want ItSmaller, efficient lamps oftoday combined withHydrel’s advanced precisionreflectors offer state-of-the-art performance. Increasedreflector-to-source area

ratios provide increased light control, and I.T.L. reportsefficiencies to 85%.

Flow-thru TechnologySealed modules inside thecontainer are impervious tomoisture penetration. There isno concern for water entry. If water runs in, it simplyevaporates or drains out thebottom of the rough-in section.

Hydrel’s innovations have created a world of difference in architectural andlandscape lighting. New photometric performance levels, modular flow-thrutechnology, and watertight lighting components combine to provide in-gradelighting users with remarkable performance. Listed below are some of the mostimportant innovations.

Better Optical PerformanceHigh performance wall washlenses give a wide, even,ovallight pattern. Before the 9000Series, effective wall washtook nearly twice the numberof fixtures.

10

Simple MaintenanceDifficult to seal -Other in-grade fixturesdepend on multiplescrews to seal lightingcomponents againstthe elements.

Relampingin an airconditionedspace ensuresthat dry air issealed insidethe lampmodule,eliminatingcondensation.

Removelocking door.

1 Lift lamp modulefrom rough-insection.

2 Unplug lampmodule. 3 Take to a clean, dry place.

Replace lamp.4Relamping Made Simple:

Relamping may be done away from hostile on-site conditions in a clean,dry environment.

Most in-gradefixtures must be

relamped on site -Relamping outside

invites condensationand moisture.

The Hydrel wayCondensation, the bane

of in-grade lighting foryears, is not a problem. Seals developed for

underwater lighting and dry air purgingensure that the presealed watertight lamp

modules contain only dry air–dry air doesnot support condensation.

The Hydrel wayThe Hydrel M9000

lamp module is easy toremove and take to a

controlled environmentfor service. No need

to relamp and resealM9000 fixtures under

difficult conditions.

The Hydrel way - prevents condensationDry air purge is maintained during relamping byremoving the lamp module to a low humiditylocation for lamp changing. The Lamp Module issealed by a clamp ringwhich is easily releasedto access the lamp. Resealing the lampmodule in the lowhumidity of the airconditioned spaceprevents condensationin the module when itis returned to theoutdoor site.

Hydrel lamp module - easy toopen, relamp, and reseal.

Hydrel lamp module - based onunderwater lighting technology.

No condensation-the result of dry airpurge eliminatingmoisture in the lampcompartment.

The end result -Condensation in thefixture, which leadsto failure.

Our competitor’s way

11

Easy Installation

Rough-in sections preventconstruction site abuse ofcritical lighting componentsA major benefit of the modular,flow- thru technology is therough- in section.The rugged corrosion-resistantcontainer can be set in place duringconstruction to await laterinstallation of lighting componentmodules.

Installation timereduced by halfOnce construction isfinished, the temporarycover is removed. Thesealed lamp and powermodules are installed.The door attaches withtwo simple fasteners.

Rough-in sections ready to be placedon site during construction.

Installation time is reduced by 50% as compared to the competition. Operating components are protected from construction site damage.

Return lamp module tosite and reconnect lampmodule.

Replace lampmodule in rough-insection.

Secure withlocking door.

Replace lens andgasket. Hand tightenclamp ring.

5 6 7 8

Pre-shipped rough-in sectioninstalled on-siteThe innovative rough-in sectionoffers installation simplicity.

Above, wired in place in a concretepour form, a rough-in section withconduit connections completed andtemporary cover in place awaitsconcrete pouring.

Trim rings are available tofacilitate clean installations incut-tile or granite floors.

Hydrel’s M9000 Series are the only in-grade fixtures that donot require sealing at ground level.The patented modular design provides a removable modulewhich can be relamped in a controlled atmosphere.

12

Rough-in section Installation

As illustrated, the rough-in section is retainedin-grade by various methods in a variety ofsubstructures.

Rough-in section - How it works

During the construction phase of a project,the rough-in section can be preinstalled onsite. Lens, lamp, and power modules, whichcould be vulnerable to construction damageare not installed at this time. Wrapped inprotective plastic, the tough engineeredpolymer rough-in section is placed flush tograde over the conduit in base materialwhich has been prepared for drainage. Whenconstruction is completed and wiring pulled,the rough-in section sheds its protectiveshrink wrap and stands ready to receive itslighting modules.

Soils

The M9000 Series eliminates the normalconcern of burying metal fixtures in alkalineand acidic soils, in areas of heavy fertilizeruse, or in salt air environments. Hydrel’sadvanced polymer materials provide for along life in all environments.

Safety

All fixtures must be grounded in accordancewith local electrical codes and the NationalElectric Code. It is recommended that thejunction box splice compartment be sealedwith re-enterable potting compound. Consultwith Hydrel’s technical support for applicationideas and safety recommendations for in-grade products.

IN SOIL IN SOIL WITH CONCRETE ANCHOR

IN SOIL WITH PROTECTIVE COLLAR CONCRETE IN SOIL

GRAVEL

SAND

BORDER BARRIER

OPTIONAL CONVEX LENS



OPTIONAL PROTECTIVECOVER

DRAINHOLES

DRAINHOLES

DRAINHOLES

DRAINHOLES

DRAINHOLES

DRAINHOLES

DRAINHOLES

NODRAINHOLES

DRAINHOLES

DRAINHOLES

TRIM RING MARBLE

PEA GRAVEL PEA GRAVEL

PEA GRAVEL PEA GRAVEL

PEA GRAVEL

PEA GRAVEL

PEA GRAVELTRENCHCOVEREDWITHTAR PAPER

PEA GRAVELCONCRETE CEILING OF SPACE BELOW

DRAINAGE SYSTEM

DRILLEDAT BASEFORREBAR

IN CONCRETE

IN MARBLE WITH TRIM RING

IN CONCRETE WITH FRENCH DRAIN

IN CONCRETE WITH DRAIN TILE SUMPIN CONCRETE ABOVE NO DRAIN AREA

IN CONCRETE OVER DRAINAGE SYSTEM

In applications where flow-through drainage is notpermitted, as in a multi-

level parking structure, theflo-thru drain holes in the

bottom of the rough-in-section can be sealed.

Consult Hydrel technicalsupport for details.

Rough-In Installation

13

Accessories/OptionsInstallation Accessories Safety Accessories

Light Control Accessories

Door Material Options

BTR Trim Ring, Polished Brass STR Trim Ring, Stainless Steel RG Rock Guard,Bronze or Aluminum

GS Glare Shield,Bronze or Aluminum

A Aluminum Door

ASP Perforated Door - stainlessperforations on aluminum

BSP Perforated Door - stainlessperforations on bronze

BBP Perforated Door - brassperforations on bronze

WWL Wall Wash LouverIHL Honey Comb Louver ISS Internal Source Shield

FLC10 10°Tilt LensFLC 5 5°Axial Spread Lens FLC20 20°Tilt Lens

LC Polycarbonate Protective Cover

SS Stainless Steel Door**listed under “Accessories”

B Bronze Door

20'

10'

30'

40'

14

Medium Flood,Wide Flood

Spots

Spot

NarrowFloods

Application

M9400 SERIES

WALLS and BUILDINGSFor light colored, smooth concrete walls:

Wall height 4' 6' 10'

Fixture M9410 M9410 M941018TRT WWD 26TRT WWD 32TRT WWD

Spacing 6' 6' 6'

Set back 1' 2' 3'

COLUMNSFor light colored, smooth concrete columns:Column height 4' 6' 10'

Fixture * M9410 M9410 M941035CMT6 SP 35CMT6 SP 70CMT6 SP

Set back 1' 1'-2' 1'-2'

SIGNSFor Small to medium ground mounted signs:Sign dimensions

(square) 2'-3' 3'-4' 4'-5'

Fixture ** M9410 M9410 M9410P3035CM MFL P3035CM MFL P3075CM MFL

Set back 1' 1'-2' 2'-3'

M9700 SERIES



Fixture * M9710 M9710 M971070M WWD 100M WWD 175M WWD

Spacing 10' 10' 10'

Set back 1' 1'-2' 1'-2'

COLUMNSFor light colored, smooth concrete columns:Column height 10' 20' 30'

Fixture ** M9710 M9710 M971035CMT6 SP 35CMT6 SP * 70CMT6 SP *

Set back 1'-2' 2'-3' 4'-5'

SIGNSFor small to medium ground mounted signs:Sign dimensions

(square) 3'-4' 6'-8' 10'-12'

Fixture ** M9710 M9710 M971050M WFL 70M WFL 175M WFL

Set back 1'-2' 2'-3' 4'-5'

FLAGSFor flag sizes 5' - 10' in width: **

Pole height SINGLE FIXTURE TWO FIXTURES THREE FIXTURESplaced up to 2' placed placed in triangledirectly 180° apart pattern 120° apartin front of pole

15' M9710 M9710 M9710100M SP 70M SP 70M SP

25' M9710 M9710 M9710150M SP 100M SP 100M SP

40' M9710 M9710 M9710175M SP 175M SP 150M SP

50' M9710 M9710 M9710175M SP 175M SP 175M SP

* M9730 can also be used

** M9720, M9730, & M9740 can also be used

15

Wall Wash

Narrow Flood,Medium Flood

NarrowFloods

Spot

Spots

Narrow Flood,Medium Flood

Spot

M9800 SERIES



Fixture M9810 M9810 M9810250ME WWD 250ME WWD 400ME WWD

Spacing 20' 20' 20'

Set back 8' 10' 12'

COLUMNSFor light colored, smooth concrete columns:

Column height 40' 20' 60'

Fixture * M9810 M9810 M9810250ME SP 250ME SP 400ME SP

Set back 2'-3' 2'-4' 2'-4'

M9800 SERIES

SIGNSFor large ground mounted signs:Sign dimensions

(square) 15' 20' 30'

Fixture ** M9820 M9820 M9820250ME MFL 250ME MFL 250ME MFL

Set back 5' 6'-8' 6'-8'

FLAGSFor flag sizes 10' - 15' in width: *

Pole height SINGLE FIXTURE TWO FIXTURES THREE FIXTURESplaced up to placed 180° apart placed / triangle 2' directly in located 1/10 pattern 120° apartfront of pole pole height located 1/10

from base pole height from base

40' M9810 M9810 M9810250ME SP 250ME SP 250ME SP




*M9820 can also be used

20'

10'

30'

40'

20'

10'

50'

40'

30'

70'

60'

16

Application TREES M9000 SeriesLamp selection according to size, structure, color enhancement:

Tree size SMALL (10-20 ft.) MEDIUM (20-40 ft.) LARGE (over 40 ft.)

Structure Open Tight Open Tight Open Tight

LAMP Fixture Fixture Fixture Fixture Fixture Fixture

MV (enhances blue) M9710 75H MFL M9710 75H SP M9710 100H MFL M9710 100H SP M9710 175H MFL M9710 175H SP

MH (enhances green) M9710 70M MFL M9710 70M SP M9710 100M MFL M9710 100M SP M9710 175M WW M9710 175M SP

QTZ (enhances white) M9410 M75 FL M9410 M75 NSP M9710 150Q MFL M9710 150Q SP M9710 250Q MFL M9710 250Q NFL

INCAN (enhances M9410 P3075 FL M9410 P3075 NSP M9710 P38250 FL M9710 P38250 SP M9710 P38250 FL M9710 P38250 SPred / yellow)

Setback 4' 2' 8'-10' 4'-7' 8'-15' 7'-16'

NOTE: When installed in areas of debris build-up use Polycarbonate protective cover LC

Medium Floods

Spot

Floods

Y

X

x = Distance of y Height x Distancesetback of fixture of object of setbackfor beam center tohit height desired. 10 ft 2.0 ft

20 ft 3.5 fty = Height of 30 ft 5.2 ftobject where 40 ft 7.0 ft beam center is 50 ft 9.0 ft desired. 60 ft 10.5 ft

70 ft 12.2 ft80 ft 14.0 ft

M9000 Series spot adjustment ranges

internal opticaladj. adj. total

Incan. units (T-4) 25º 10º 35ºHID units (E17/A23) 12º 10º 22º

PAR38 units 15º 10º 25º

Optical aiming of M9000 Series10° tilt lens for Spot Applications

A pair of 175 Watt M9700 metalhalides effectively wash a groveof seventy-foot-tall pine treeswith a soft even glow.

18

Ordering and Specification Guide

Model

Material

Wattage & LampAll fixtures ship w/ lamp installed.Not all lamp types available with all distributions.For MR16, PAR lamps, consult lamp manufacturer.

VoltageNot all Voltage / Lampcombinations areavailable, consultfactory for moreinformation.

DistributionSee Lamp Type for availabledistributions.

LensDouble lens (M9420,M9440) always ship w/FLC on lower lampmodule and specified lens onupper finishing section.

Conduit Entries

Accessories

EXAMPLE

M9410 Round Single LensM9420 Round Double LensM9430 Square Single LensM9440 Square Double Lens

A AluminumB BronzeSS Stainless Steel

ASP 1 Alum. w/ Stainless Perf. BBP 1 Bronze w/ Brass Perf. BSP 1 Bronze w/ Stainless Steel Perf.

AAS 1 Alum. Door, Solid Alum. Insert ASS 1 Alum. Door, Solid Stainless Steel InsertBBS 1 Bronze Door, Solid Bronze InsertBSS 1 Bronze Door, Solid Stainless Steel Insert

VNSP Very Narrow Spot NSP Narrow Spot SP Spot NFL Narrow FloodFL FloodMFL Medium FloodWFL Wide FloodVWFL Very Wide FloodWWD 5 Wall Wash ASY 6 Asymmetric Flood

CLC Convex, ClearCLF Convex, FrostedFLC Flat, ClearFLC5 Flat, Clear, 5° axial spreadFLC10 Flat, Clear, 10° tiltFLC20 Flat, Clear, 20° tiltFLCAS Flat, Clear, Anti-slipFLC10AS Flat, Anti-slip, 10° tilt FLF Flat, FrostedFLF5 Flat, Frosted, 5° axial spreadFLFAS Flat, Frosted, Anti-slip

U.S. 12B 1/2" NPT bottom12S 1/2" NPT side34B 3/4" NPT bottom34S 3/4" NPT side

EUROPEAN16B PG16 bottom16S PG16 side20B M20 bottom20S M20 side25B M25 bottom

INTERNAL 7

IHL Internal Honeycomb LouverISS 8 Internal Source Shield WWL Wall Wash LouverLSF Linear Spread FilterCFAMB Color Filter AmberCFBLU Color Filter BlueCFGRN Color Filter GreenCFRED Color Filter Red

EXTERNAL DOOR 9, 10

RG Rockguard GS Glare Shield LC Polycarbonate Protective Cover

EXTERNAL TRIM 9

STR 11 Stainless Steel Trim Ring, Round STS 12 Stainless Steel Trim Ring, SquareBTR 11 Brass Trim Ring, Round BTS 12 Brass Trim Ring, Square

Options

Lamping

Finish 17

M9410 A 70CMT6 120 SP FLC 34B ISS STR SF LP

Listing

BL BlackBZ BronzeDDB Dark BronzeDNA Natural AluminumGN GreenGR GraySND SandSTG Steel GrayTVG Terra Verde greenWH WhiteCF Custom

SF13 Single fuseDF14 Double FuseGEB15 Electronic Ballast MLEBAD16 Electronic Ballast

Analog Dimming

LP Lamp Installed IEC InternationalElectrotechnical Commission

VOLTAGE (60HZ) 120 220277 208240 347MVOLT(120-277) 3

VOLTAGE (50HZ) 22050HZ 23050HZ24050HZ

LOW VOLTAGE(60 HZ & 50 HZ) 12 4

1 Not available for M9430, M9440 Models. Available with unpainted finish only.2 Available with GEB ballasts only.3 Standard on fluorescent lamps and MH lamps with GEB Ballasts.4 Low voltage transformer required. Sold separately.5 FLC5 (fluorescent) or FLF5 (HID) lens included standard. WWD available with fluorescent and T4 (Incan, HID) lamps only.6 ASY available with fluorescent lamps only.7 Not available with ASY distribution. 8 Not available with WWD distribution.9 Not available with SS material.10 Mutually exclusive, choose one only.11 Available with M9410, M9420 only.12 Available with M9430, M9440 only.13 Available with 120V, 277V, and 347V only.14 Available with 208V, 220V, and 240V only.15 Available with MVOLT(120V-277V) voltage only for Metal Halide lamps to 150Watt maximum.16 For use with 0V to 10V analog dimmer (by others). Additional electrical conductors are required. Consult Hydrel for details.17 Standard finish is unpainted unless specified.

FLUORESCENT (U.S. & EUROPEAN)18TRT 18W Triple Tube Gx24q-2 26TRT 26W Triple Tube Gx24q-3 32TRT 32W Triple Tube Gx24q-3Distributions ASY, MFL, WWD

LAMP TYPE HID color correctedU.S. EUROPEAN

20CMT4 2 20W (MH) T4 G8.5 G8.535CMT4 35W (MH) T4 G8.5 G8.570CMT4 70W (MH) T4 G8.5 G8.535CMT6 35W (MH) T6 G12 G1270CMT6 70W (MH) T6 G12 G12P2035CM 35W (MH) PAR20 MED E27P3035CM 35W (MH) PAR30 MED E27P3070CM 70W (MH) PAR30 MED E27Distributions SP, FL, WFL

LAMP TYPE INCANDESCENT (U.S.)P1645I 45W PAR16 MED P1660I 60W PAR16 MED P1675I 75W PAR16 MED P2050I 50W PAR20 MED P3050I 50W PAR30 MED P3075I 75W PAR30 MED 75Q 75W T4 Mini-can 100Q 100W T4 Mini-can Distributions SP, NFL, FL, WFL

LAMP TYPE INCANDESCENT (EUROPEAN)P1640I 40W PAR16 E27P2050I 50W PAR20 E27P3050I 50W PAR30 E27P3075I 75W PAR30 E27100QB 100W T4 B15d Distribution NSP, SP, FL, MFL

LAMP TYPE LOW VOLTAGE (U.S. & EUROPEAN)M20 20W MR16 GU5.3M50 50W MR16 GU5.3M75 75W MR16 GU5.3P3635ILV 35W PAR36 SCREWP3636ILV 36W PAR36 SCREWP3650ILV 50W PAR36 SCREWP3675ILV 75W PAR36 SCREWDistributions VNSP, NSP, NFL, FL, WFL

U.L. and C.U.L. Listedfor wet locations.NEMKO IP67 Rating

CE N

Hydrel is a ISO9001Registered Quality SystemCompany

For more information, contact the factory orvisit the Hydrel website:www.hydrel.com

To order, use a single master catalog number: Example: M9410 A 70CMT6 120 SP FLC 34B ISS STR SF LP

Fixture ships as multiplecomponents:

(1) MRIS94RL 34B (Housing)(1) MFS94R A STR (Finishing Section)(1) MACS 70CMT6 SP FLC ISS LP (Lamp Module)(1) MHSL94 70CMT6 120 (Ballast Power Module)

19


Lamping

Finish 18

LP


LP Lamp Installed

Listing

IEC InternationalElectrotechnical Commission

Model

Material

Wattage & LampAll fixtures ship w/ lamp installed.Not all lamp types available with all distributions.For MR16, PAR lamps, consult lamp manufacturer.

VoltageNot all Voltage / Lamp combinations are available, consult factory for more information.

DistributionSee Lamp Type foravailable distributions.

LensDouble lens (M9720,M9740) alwaysship w/FLC on lower lamp moduleand specified lens on upper finishingsection.

Conduit Entries

Accessories

EXAMPLE

M9710 Round Single LensM9720 Round Double LensM9730 Square Single LensM9740 Square Double Lens

A AluminumB BronzeSS Stainless Steel

ASP 1,2 Alum. w/ Stainless Steel Perf. BBP 1,2 Bronze w/ Brass Perf. BSP 1,2 Bronze w/ Stainless Steel Perf.

AAS 1,2 Alum. Door, Solid Alum. Insert ASS 1,2 Alum. Door, Solid Stainless Steel InsertBBS 1,2 Bronze Door, Solid Bronze Insert BSS 1,2 Bronze Door, Solid Stainless Steel Insert

NSP Narrow Spot SP Spot NFL Narrow FloodMFL Medium FloodFL FloodWFL Wide FloodWWD 4, Wall Wash

CLC Convex, ClearCLF Convex, FrostedFLC Flat, ClearFLC5 5 Flat, Clear, 5° axial spreadFLC10 Flat, Clear, 10° tiltFLC20 Flat, Clear, 20° tiltFLCAS Flat, Clear, Anti-slipFLC10AS Flat, Anti-slip, 10° tiltFLF Flat, FrostedFLF5 Flat, Frosted, 5° axial spreadFLFAS Flat, Frosted, Anti-slip



INTERNALIHL Internal Honeycomb Louver ISS 6 Internal Source Shield WWL 7 Wall Wash LouverLSF Linear Spread FilterCFAMB Color Filter AmberCFBLU Color Filter BlueCFGRN Color Filter GreenCFRED Color Filter Red

EXTERNAL DOOR 8

RG 9 Rockguard GS Glare Shield LC 10 Polycarbonate Protective Cover

EXTERNAL TRIM STR 11,13 Stainless Steel Trim Ring, Round STS 12,13 Stainless Steel Trim Ring. SquareBTR 11.13 Brass Trim Ring, Round BTS 12,13 Brass Trim Ring. SquarePRR 11 Protective Ring, Round PRS 12 Protective Ring, Square GM Grout Mask

Options

M9710 A 150CMT6 120 NSP FLC 34B ISS STR SF

SF14 Single FuseDF15 Double FuseGEB16 Electronic BallastMLEBAD16,17 Electronic Ballast

Analog Dimming

VOLTAGE (60HZ) 120 220277 208240 347MVOLT (120-277) 3


LAMP TYPE INCANDESCENT PAR38 U.S. EUROPEAN

P38100I 100W MED. E27P38150I 150W MED. E27P38250I 250W MED. NADistribution SP, FL

LAMP TYPE QUARTZ U.S. EUROPEAN

100Q 100W T4 Mini-can 100QE 100W E27150Q 150W T4 Mini-can 100QB 150W BA15D250Q 250W T4 Mini-can 150QE 150W E27

250QB 250W BA15D250QE 250W E27

Distribution NSP, SP, NFL, MFL, WFL, WWD

LAMP TYPE FLUORESCENT (U.S. & EUROPEAN)18TRT 18W Triple Tube Gx24q-2 26TRT 26W Triple Tube Gx24q-332TRT 32W Triple Tube Gx24q-342TRT 42W Triple Tube) Gx24q-4Distributions SP, NFL, MFL, WFL, WWD

LAMP TYPE HIDU.S. EUROPEAN

50S 50W (HPS) E17, MED. Ellip., E2770S 70W (HPS) E17, MED. Ellip., E27100S 100W (HPS) E17, MED. E26 only150S 150W (HPS) E17, MED. E26 only50H 50W (MV) E17, MED. Ellip., E2775H 75W (MV) E17, MED. NA80H 80W (MV) NA Ellip., E27100H 100W (MV) E17, MED. NA125H 125W (MV) NA Ellip., E27175H 175W (MV) E17, MED. NA50M 50W (MH) E17, MED. NA70M 70W (MH) E17, MED. Ellip., E27100M 100W (MH) E17, MED. Ellip., E27150M 150W (MH) E17, MED. Ellip., E27175M 175W (MH) E17, MED. NADistributions SP, NFL, MFL, WFL, WWD

LAMP TYPE HID PAR38 (U.S. only)P38100H 100W (MV) MED.P3870M 70W (MH) MED.P38100M 100W (MH) MED.P38150M 150W (MH) MED.Distributions SP, FL, VWFL

LAMP TYPE HID color corrected70CM 70W (MH) E17, MED. NA100CM 100W (MH) E17, MED. NA150CM 150W (MH) E17, MED. NA35CMT6 35W (MH) T6, G12 T6, G1270CMT6 70W (MH) T6, G12 T6, G12150CMT6150W (MH) T6, G12 T6, G12Distributions NSP, NFL, MFL, WFL, WWD

LAMP TYPE HID color corrected (U.S. only)P3870CM 70W (MH) MED.P38100CM100W (MH) MED.Distributions SP, FL, WFL

1 Not available w/ M9730, M9740 Models. Available with unpainted finish only.2 Available to 100 Watt max only.3 Standard on fluorescent lamps and MH lamps with GEB Ballasts.4 FLF5 lens recommended for 70 watt HID and lower. FLC5 lens recommended for 100 Watt HID and higher.5 Default lens for WWD distribution Quartz, Fluorescent, and 100 Watt HID and higher.6 ISS not available with PAR or fluorescent lamps, or WWD distribution.7 Not available with PAR lamps.8 Not available with SS material. Accessories are mutually exclusive, choose one only.9 RG not available with CLC or CLF convex lens.10 LC not available for M9710, M9730.11 Available with M9710, M9720 only.12 Available with M9730, M9740 only.13 Not available with SS material.14 Available with 120V, 277V, and 347V only.15 Available with 208V, 220V, and 240V only.16 Available with MVOLT (120V-277V) voltage only for Metal Halide lamps to 150Watt maximum. 17 For use with 0V to 10V analog dimmer (by others). Additional electrical conductors are required. Consult Hydrel for details.18 Standard finish is unpainted unless specified.


CE N



To order, use a single master catalog number: Example: M9710 A 150CMT6 120 SP NSP FLC 34B ISS STR SF LP


(1) MRIS97RL 34B (Housing)(1) MFS97R A STR (Finishing Section)(1) MACL 150CMT6 NSP FLC ISS LP (Lamp Module)(1) MHSL97 150CMT6 120 (Ballast Power Module)

20


Model

Material

Wattage & LampAll fixtures ship w/ lamp installedNot all lamp types available with all distributions.For MR16, PAR lamps, consult lamp manufacturer.

VoltageNot all Voltage / Lampcombinations areavailable, consult factory for more information.

DistributionSee Lamp Type foravailable distributions.

LensDouble lens (M9820) alwaysship w/FLC on lower lampmodule and specified lenson upper finishing section.

Conduit Entries

Accessories

EXAMPLE

M9810 Round Single LensM9820 Round Double Lens

A AluminumB Bronze

AAS 1 Alum. Door, Solid Alum. Insert ASS 1 Alum. Door, Solid Stainless Steel InsertBBS 1 Bronze Door, Solid Bronze Insert BSS 1 Bronze Door, Solid Stainless Steel Insert

NSP Narrow Spot SP Spot MFL Medium FloodWFL Wide FloodWWD 2,3 Wall Wash

FLC Flat, ClearFLC5 Flat, Clear, 5° axial spreadFLC10 4 Flat, Clear, 10° tiltFLC20 4 Flat, Clear, 20° tilt



INTERNAL IHL Internal Honeycomb LouverISS 5 Internal Source Shield WWL 3 Wall Wash Louver

EXTERNAL DOOR 6

RG Rockguard GS Glare Shield

EXTERNAL TRIMSTR Stainless Steel Trim Ring, Round BTR Brass Trim Ring, Round

M9810 B 400ME 120 SP FLC 34B ISS BTR

VOLTAGE (60HZ) 120 220277 208240 347


1 Available to 250 Watt max only. Available with unpainted finish only.2 FLC5 lens included standard.3 Not available with PAR lamps.4 FLC10 and FLC20 not available on M9810.5 ISS not available with PAR lamps or WWD distribution.6 Mutually exclusive, choose one only.7 Available with 120V, 277V, and 347V only.8 Available with 208V, 220V, and 240V only.9 Standard finish is unpainted unless specified.

LAMP TYPE INCANDESCENT (U.S.)P56300I 300W PAR56 Ext.Mogul End Prong P64500I 500W PAR64 Ext.Mogul End Prong Distributions NSP, SP, MFL, WFL

LAMP TYPE INCANDESCENT (EUROPEAN)P56300I 300W PAR56 GX16D P64500I 500W PAR64 GX16D Distributions SP, MFL, WFL

LAMP TYPE HID (U.S.)250ST 250W (HPS)E18 Mogul 400ST 400W (HPS)E18 Mogul 175ME 175W (MH) E231/2 Mogul 250ME 250 (MH) E28 Mogul 400ME 400W (MH) E37 Mogul Distributions SP, MFL, WWD

LAMP TYPE HID (EUROPEAN)250ST 250W (HPS)Tubular E40 400ST 400W (HPS)Tubular E40 250MT 250W (MH) Tubular E40 400MT 400W (MH) Tubular E40 Distributions SP, MFL, WWD

A number of M9700s with 175 Watt

metal halide lampsilluminate the facade of

the famous landmarkChicago Water Tower.


CE N



To order, use a single master catalog number: Example: M9810 B 400ME 120 SP FLC 34B ISS BTR SF LP STG


(1) MRIS98RL 34B (Housing)(1) MFS98R B BTR (Finishing Section)(1) MACXL 400ME SP FLC ISS LP (Lamp Module)(1) MHSL98 400ME 120 (Ballast Power Module)

Options

Lamping

Finish 9

SF LP

Listing


SF 7 Single FuseDF 8 Double Fuse

LP Lamp Installed IEC InternationalElectrotechnical Commission

Hydrel Website: www.hydrel.comVisit our website for specification sheets, installationinstructions, and a comprehensive selection ofphotometric data for the products in this catalog,as well as for most other Hydrel products.

HYDRELAcuity Lighting Group, Inc.12881 Bradley Avenue, Sylmar, CA 91342Phone 818-362-9465, Fax 818-362-6548Visit our website at www.hydrel.com

Hydrel is ISO9001 Certified

©2005 Acuity Brands 6/05 Form U. 106.3

M9000 SERIES IN-GRADE LIGHTING · The M9000 has a range of32Watts to400Watts in a variety of lamp...

Documents

Transcript of M9000 SERIES IN-GRADE LIGHTING · The M9000 has a range of32Watts to400Watts in a variety of lamp...