m geneRal InfoRmaTIon e CH Bt (BlUe-tiP) Screw Bolt...
Transcript of m geneRal InfoRmaTIon e CH Bt (BlUe-tiP) Screw Bolt...
www.DEWALT.com/anchors50
GeneRal InfoRMaTIon
TecH ManUal – M
ecHanIcal ancHoRs ©2013 D
eWalT PRInTeD 6/13
meC
Han
iCal a
nCHo
rS
geneRal InfoRmaTIon
Bt (BlUe-tiP)Screw Bolt
ProDUCt DeSCriPtion
The blue-Tip is a heavy duty screw anchor with a finished hex head. The one piece design makes it easy to install and the preferred choice for fast, reliable anchoring and is also fully removable. This anchor is designed to resist structural and non-structural loading in cracked and uncracked concrete.
General aPPliCationS anD USeS
featUreS anD BenefitS
•consistent performance in high and low strength concrete
•nominal drill bit size is same as anchor denomination
•Quick and easy installation with a powered impact wrench
•special dust relief thread
•approved for two embedment depths
aPProValS anD liStinGS
ETAG 001 Option 1 F120
loaDinG ConDitionS
STATIC QUASI-STATIC
SUitaBle BaSe materialS
secTIon conTenTsGeneral Information
Installation Information
Design Information
Material Information
ordering Information
assembly
Hex Head With formed Washer
screw With Dual Thread
Taper Tip
VeRsIonsHex Head
carbon steel, Zinc Plated
stainless steel (no eTa approval)
Mechanically Galvanized (no eTa approval)
appRoVals• eTa-12/0607
DEWALT DESIGN ASSISTReal-Time anchor Design software
www.DeWalTdesignassist.com
www.DEWALT.com/anchors 51
InsTallaTIon InfoRMaTIon
TecH
Man
Ual
– M
ecHa
nIca
l an
cHoR
s ©
2013
DeW
alT
PRI
nTeD
6/1
3m
eCHan
iCal
an
CHo
rSInsTallaTIon InfoRmaTIon
inStallation Data
notation UnitbT
bT10 bT12 bT16
anchor diameter d [mm] 9.7 11.6 15.2
nominal drill bit diameter d0 [mm] 10 12 16
Diameter of hole clearance in fixture df [mm] 12 14 19
nominal embedment depth 1 nominal embedment depth 2
hnom,1 hnom,2
[mm] [mm]
55 75
70 85
80 110
effective embedment depth 1 effective embedment depth 2
hef,1 hef,2
[mm] [mm]
40 57
51 64
57 83
Drill hole depth for hef,1 Drill hole depth for hef,2
h1,1 h1,2
[mm] [mm]
65 85
60 95
90 125
Minimum member thickness for hef,1 Minimum member thickness for hef,2
hmin,1 hmin,2
[mm] [mm]
105 115
125 125
145 165
Minimum spacing smin [mm] 60 90 110
Minimum edge distance cmin [mm] 60 90 110
Torque wrench socket size sw [mm] 17 19 23
hmin
hnom
d0
df
Sw
h1
tfix
L
inStallation inStrUCtionS
1.) Using the proper drill bit size, drill a hole into the base material to the required depth.
2.) Remove dust and debris from the hole using a hand pump or compressed air.
3.) Select impact wrench and mount the screw anchor head into the hex socket.
4.) Drive the anchor through the fixture into the hole at least to the minimum required embedment depth and until the head of the anchor comes into contact with the fixture.
for complete installation instructions, see technical approval.
52
TecH ManUal – M
ecHanIcal ancHoRs ©2013 D
eWalT PRInTeD 6/13
DesIGn InfoRMaTIon
www.DEWALT.com/anchors
meC
Han
iCal a
nCHo
rS
DesIgn InfoRmaTIon
tenSion loaD CaPaCitieS - ParameterS for CalCUlation of DeSiGn StrenGtHAccording to ETAG 001 Annex C Method A.
notation UnitbT
bT10 bT12 bT16
steel failure
characteristic resistance nRk,s [kn] 56.0 78.5 140.4
Partial safety factor gMs [-] 1.4
pullout failure
Cracked concrete
characteristic resistance (hef,1) nRk,p [kn] 3 4 7.5
characteristic resistance (hef,2) nRk,p [kn] 6 5 12
Partial safety factor gMp
1) [-] 2.12) 1.83)
Uncracked concrete
characteristic resistance (hef,1) nRk,p [kn] 7.5 12 16
characteristic resistance (hef,2) nRk,p [kn] 12 16 25
Partial safety factor gMp
1) [-] 2.12) 1.83)
Increasing factor for concrete strength
c30/37 cc [-] 1.15
c40/50 cc [-] 1.27
c50/60 cc [-] 1.36
concrete failure
Concrete cone failure
characteristic spacing (hef,1) scr,n,1 [mm] 120 154 172
characteristic spacing (hef,2) scr,n,2 [mm] 171 192 248
characteristic edge distance (hef,1) ccr,n,1 [mm] 60 77 86
characteristic edge distance (hef,2) ccr,n,2 [mm] 86 96 124
Partial safety factor gMc
1) [-] 2.12) 1.83)
Splitting failure
characteristic spacing (hef,1) scr,sp,1 [mm] 120 154 172
characteristic spacing (hef,2) scr,sp,2 [mm] 171 192 248
characteristic edge distance (hef,1) ccr,sp,1 [mm] 60 77 86
characteristic edge distance (hef,2) ccr,sp,2 [mm] 86 96 124
Partial safety factor gMsp
1) [-] 2.12) 1.83)
Increasing factor for concrete strength
c30/37 cc [-] 1.15
c40/50 cc [-] 1.27
c50/60 cc [-] 1.36
1) In absence of other national regulations
2) The partial safety factor g2 = 1.4 is included
3) The partial safety factor g2 = 1.2 is included
DEWALT DESIGN ASSIST
The DeWalT Design assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWalT anchor products is readily available. To download this software for free, go to www.DeWalTdesignassist.com
www.DEWALT.com/anchors 53
TecH
Man
Ual
– M
ecHa
nIca
l an
cHoR
s ©
2013
DeW
alT
PRI
nTeD
6/1
3
DesIGn InfoRMaTIon
meC
Han
iCal
an
CHo
rSSHear loaD CaPaCitieS - ParameterS for CalCUlation of DeSiGn StrenGtH
According to ETAG 001 Annex C Method A.
notation UnitbT
bT10 bT12 bT16
steel failure
Steel failure without lever arm
characteristic resistance VRk,s [kn] 27.0 35.8 55.1
Partial safety factor gMs
1) [-] 1.5
Steel failure with lever arm (bending)
characteristic resistance M0Rk,s [nm] 77 128 306
Partial safety factor gMs
1) [-] 1.5
concrete failure
Pry-out failure
factor in equation (5.6) of eTaG 001 annex c for hef,1 k1 [-] 1 1 2
factor in equation (5.6) of eTaG 001 annex c for hef,2 k2 [-] 1 2 2
Partial safety factor gMc
1) [-] 1.5
Edge failure
effective length of anchor for hef,1 lf,1 [mm] 40.0 51.4 57.2
effective length of anchor for hef,2 lf,2 [mm] 57.0 64.1 82.7
outside diameter of anchor dnom [mm] 10 12 16
Partial safety factor gMc
1) [-] 1.52)
1) In absence of other national regulations
2) The partial safety factor g2 = 1.0 is included
PreCalCUlateD tenSion anD SHear CaPaCitieS According to ETAG 001 Annex C Method A.
•Thefollowingtablesaremeanttogivethedesigneraidinthepreliminarydesignprocess.Noresponsibilityistakenforthecorrectness of these data.
•ThegivenvaluesarevalidfornormalconcreteC20/25andstatic/quasi-staticloadswiththeexactdimensionalinformationgiven. for any other conditions, the use of DDa is recommended.
•Thevaluesinthetablesbelowaredesignlevelloads.Thisassumesasafetyfactorisincludedbothontheloading and the resistance.
•Forcrackedconcrete,splittingfailureisnotconsideredassumingthatareinforcementispresentwhichlimitsthecrack width to 0.3 mm.
•Forfurtherdetailsandbackgroundinformationpleaseseetheintroductionofthismanual.
N
V
F
sh
c
bT10Embedment Depth 1
c20/25
anchoring located far from any edge anchoring located close to an edge
embedment depth hef [mm] 40.0
Member thickness h [mm] 105
edge distance c [mm] - - - - - 60 60 60 60 60
anchor spacing s [mm] - 60 120 60 120 - 60 120 60 120
nRd [kn] 1.4 2.9 2.9 5.7 5.7 1.4 2.9 2.9 5.7 5.7
fRd45° [kn] 2.0 3.7 3.9 6.8 7.9 1.8 3.2 3.4 4.7 5.3
VRd [kn] 6.1 9.1 12.1 13.7 24.3 4.1 5.5 6.9 5.5 6.9
nRd [kn] 3.6 7.1 7.1 13.7 14.3 3.6 7.1 7.1 13.7 14.3
fRd45° [kn] 4.3 7.8 8.5 13.5 17.1 3.8 6.3 7.0 8.4 9.8
VRd [kn] 8.5 12.8 17.0 19.1 34.0 5.8 7.7 9.7 7.7 9.7
n - steel strengths controls n - concrete strength controls n - anchor pullout strength controls
DEWALT DESIGN ASSIST
The DeWalT Design assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWalT anchor products is readily available. To download this software for free, go to www.DeWalTdesignassist.com
54
TecH ManUal – M
ecHanIcal ancHoRs ©2013 D
eWalT PRInTeD 6/13
DesIGn InfoRMaTIon
www.DEWALT.com/anchors
meC
Han
iCal a
nCHo
rS
bT10Embedment Depth 2
c20/25
anchoring located far from any edge anchoring located close to an edge
embedment depth hef [mm] 57.0
Member thickness h [mm] 115
edge distance c [mm] - - - - - 60 60 60 60 60
anchor spacing s [mm] - 60 171 60 171 - 60 171 60 171
nRd [kn] 2.9 5.7 5.7 11.4 11.4 2.9 5.7 5.7 10.9 11.4
fRd45° [kn] 3.8 6.9 7.6 12.1 15.2 2.9 4.9 5.8 6.4 8.3
VRd [kn] 10.3 14.0 20.7 18.8 41.3 4.4 5.8 8.5 5.8 8.5
nRd [kn] 5.7 11.4 11.4 18.8 22.9 5.7 10.8 11.4 15.3 22.9
fRd45° [kn] 7.0 12.2 13.9 18.7 27.8 5.0 7.9 9.9 9.1 13.4
VRd [kn] 14.5 19.5 28.9 26.4 57.8 6.2 8.2 12.0 8.2 12.0
n - steel strengths controls n - concrete strength controls n - anchor pullout strength controls
bT12Embedment Depth 1
c20/25
anchoring located far from any edge anchoring located close to an edge
embedment depth hef [mm] 51.0
Member thickness h [mm] 125
edge distance c [mm] - - - - - 90 90 90 90 90
anchor spacing s [mm] - 90 153 90 153 - 90 153 90 153
nRd [kn] 1.9 3.8 3.8 7.6 7.6 1.9 3.8 3.8 7.6 7.6
fRd45° [kn] 2.7 5.1 5.3 9.6 10.6 2.6 4.6 4.8 7.3 7.8
VRd [kn] 8.7 13.8 17.4 21.9 34.7 7.3 9.7 11.4 9.7 11.4
nRd [kn] 5.7 11.4 11.4 21.9 22.9 5.7 11.4 11.4 21.9 22.9
fRd45° [kn] 6.6 12.2 13.2 21.7 26.4 6.2 10.6 11.4 14.3 16.1
VRd [kn] 12.2 19.4 24.4 30.7 48.6 10.3 13.7 16.1 13.7 16.1
n - steel strengths controls n - concrete strength controls n - anchor pullout strength controls
bT12Embedment Depth 2
c20/25
anchoring located far from any edge anchoring located close to an edge
embedment depth hef [mm] 64.1
Member thickness h [mm] 125
edge distance c [mm] - - - - - 90.0 90 90 90 90
anchor spacing s [mm] - 90 192 90 192 - 90 192 90 192
nRd [kn] 2.4 4.8 4.8 9.5 9.5 2.4 4.8 4.8 9.5 9.5
fRd45° [kn] 3.4 6.7 6.7 13.5 13.5 3.1 5.5 5.9 8.3 9.3
VRd [kn] 23.9 35.9 47.7 52.7 95.5 7.6 10.1 13.0 10.1 13.0
nRd [kn] 7.6 15.2 15.2 26.4 30.5 7.6 15.2 15.2 24.9 30.5
fRd45° [kn] 9.8 19.6 19.6 33.0 39.2 7.6 12.5 14.1 15.4 19.4
VRd [kn] 23.9 47.7 47.7 73.8 95.5 10.7 14.3 18.3 14.3 18.3
n - steel strengths controls n - concrete strength controls n - anchor pullout strength controls
DEWALT DESIGN ASSIST
The DeWalT Design assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWalT anchor products is readily available. To download this software for free, go to www.DeWalTdesignassist.com
www.DEWALT.com/anchors 55
TecH
Man
Ual
– M
ecHa
nIca
l an
cHoR
s ©
2013
DeW
alT
PRI
nTeD
6/1
3
MaTeRIal InfoRMaTIon
meC
Han
iCal
an
CHo
rS
bT16Embedment Depth 1
c20/25
anchoring located far from any edge anchoring located close to an edge
embedment depth hef [mm] 57.2
Member thickness h [mm] 145
edge distance c [mm] - - - - - 110 110 110 110 110
anchor spacing s [mm] - 110 171 110 171 - 110 171 110 171
nRd [kn] 4.2 8.3 8.3 16.7 16.7 4.2 8.3 8.3 16.7 16.7
fRd45° [kn] 5.9 11.4 11.8 21.8 23.6 5.0 8.7 9.1 12.5 13.4
VRd [kn] 20.8 34.1 41.5 55.9 83.1 9.9 13.1 15.0 13.1 15.0
nRd [kn] 8.9 17.8 17.8 32.6 35.6 8.9 17.8 17.8 32.6 35.6
fRd45° [kn] 11.6 22.0 23.1 39.1 46.2 9.2 15.4 16.4 20.1 22.5
VRd [kn] 29.1 47.7 58.1 78.3 116.3 13.9 18.6 21.1 18.6 21.1
n - steel strengths controls n - concrete strength controls n - anchor pullout strength controls
bT16Embedment Depth 2
c20/25
anchoring located far from any edge anchoring located close to an edge
embedment depth hef [mm] 83.0
Member thickness h [mm] 165
edge distance c [mm] - - - - - 110 110 110 110 110
anchor spacing s [mm] - 110 248 110 248 - 110 248 110 248
nRd [kn] 6.7 13.3 13.3 26.7 26.7 6.7 13.3 13.3 26.7 26.7
fRd45° [kn] 9.4 18.0 18.9 33.5 37.7 7.1 12.0 13.5 16.3 19.2
VRd [kn] 36.3 52.4 72.7 75.6 145.1 11.2 15.0 19.7 15.0 19.7
nRd [kn] 13.9 27.8 27.8 44.1 55.6 13.9 27.7 27.8 40.8 55.6
fRd45° [kn] 17.1 34.2 34.2 52.8 68.4 12.6 20.4 23.6 23.6 31.5
VRd [kn] 36.7 73.3 73.5 105.9 146.9 15.9 21.1 27.8 21.1 27.8
n - steel strengths controls n - concrete strength controls n - anchor pullout strength controls
DEWALT DESIGN ASSIST
The DeWalT Design assist is a powerful anchor design software which helps you to design simple and complex anchorages.The design data of all DeWalT anchor products is readily available. To download this software for free, go to www.DeWalTdesignassist.com
maTeRIal InfoRmaTIon
material SPeCifiCation
1
part no. Designation material protection
1 screw bolt special hardened c-steel Zinc plated 5 µm
56
TecH ManUal – M
ecHanIcal ancHoRs ©2013 D
eWalT PRInTeD 6/13
oRDeRInG InfoRMaTIon
www.DEWALT.com/anchors
meC
Han
iCal a
nCHo
rS
oRDeRIng InfoRmaTIon
art. no. Type Dia. length
[mm]box qty.
carton qty.
BT (M6-M8)
BT (M10-M16)
Blue-Tip (BT) Screw anchor - zinc plated
DfM1410000 5x50 Hex head screw bolt - zinc plated M5 50 100 800
DfM1410030 6x30 Hex head screw bolt - zinc plated M6 30 100 800
DfM1410050 6x50 Hex head screw bolt - zinc plated M6 50 100 800
DfM1410070 6x60 Hex head screw bolt - zinc plated M6 60 100 800
DfM1410090 6x80 Hex head screw bolt - zinc plated M6 80 50 400
DfM1410110 6x100 Hex head screw bolt - zinc plated M6 100 100 400
DfM1410130 6x120 Hex head screw bolt - zinc plated M6 120 100 400
DfM1410150 6x140 Hex head screw bolt - zinc plated M6 140 50 200
DfM1410180 8x50 Hex head screw bolt - zinc plated M8 50 50 400
DfM1410210 8x75 Hex head screw bolt - zinc plated M8 75 50 200
DfM1410240 8x100 Hex head screw bolt - zinc plated M8 100 50 200
DfM1410280 10x60 Hex head screw bolt - zinc plated M10 60 50 200
DfM1410320 10x75 Hex head screw bolt - zinc plated M10 75 50 200
DfM1410360 10x100 Hex head screw bolt - zinc plated M10 100 50 200
DfM1410400 10x110 Hex head screw bolt - zinc plated M10 110 25 100
DfM1410430 10x120 Hex head screw bolt - zinc plated M10 120 25 100
DfM1410450 10x140 Hex head screw bolt - zinc plated M10 140 25 100
DfM1410480 10x160 Hex head screw bolt - zinc plated M10 160 20 80
DfM1410510 10x200 Hex head screw bolt - zinc plated M10 200 20 80
DfM1410540 10x240 Hex head screw bolt - zinc plated M10 240 50 200
DfM1410580 10x280 Hex head screw bolt - zinc plated M10 280 50 200
DfM1410620 10x320 Hex head screw bolt - zinc plated M10 320 50 200
DfM1410650 12x75 Hex head screw bolt - zinc plated M12 75 25 100
DfM1410680 12x100 Hex head screw bolt - zinc plated M12 100 25 100
DfM1410710 12x150 Hex head screw bolt - zinc plated M12 150 20 80
DfM1410740 12x200 Hex head screw bolt - zinc plated M12 200 20 80
DfM1410770 16x100 Hex head screw bolt - zinc plated M16 100 20 80
DfM1410800 16x130 Hex head screw bolt - zinc plated M16 130 10 40
DfM1410830 16x150 Hex head screw bolt - zinc plated M16 150 10 40
DfM1410860 16x200 Hex head screw bolt - zinc plated M16 200 10 40
DfM1410890 16x240 Hex head screw bolt - zinc plated M16 240 20 80
DfM1410920 16x280 Hex head screw bolt - zinc plated M16 280 20 80
DfM1410950 16x320 Hex head screw bolt - zinc plated M16 320 25 100
www.DEWALT.com/anchors 57
TecH
Man
Ual
– M
ecHa
nIca
l an
cHoR
s ©
2013
DeW
alT
PRI
nTeD
6/1
3
oRDeRInG InfoRMaTIon
meC
Han
iCal
an
CHo
rSart.
no. Type Dia. length [mm]
box qty.
carton qty.
BT-Mg
Blue-Tip (BT) Screw anchor - mechanically galvanized
DfM1460000 6x50 Hex head screw bolt - mechanically galvanized M6 50 100 800
DfM1460030 6x60 Hex head screw bolt - mechanically galvanized M6 60 100 800
DfM1460060 6x80 Hex head screw bolt - mechanically galvanized M6 80 50 400
DfM1460090 6x100 Hex head screw bolt - mechanically galvanized M6 100 100 400
DfM1460120 6x120 Hex head screw bolt - mechanically galvanized M6 120 100 400
DfM1460150 6x140 Hex head screw bolt - mechanically galvanized M6 140 50 200
DfM1460180 8x50 Hex head screw bolt - mechanically galvanized M8 50 50 400
DfM1460210 8x75 Hex head screw bolt - mechanically galvanized M8 75 50 200
DfM1460240 8x100 Hex head screw bolt - mechanically galvanized M8 100 50 200
DfM1460270 10x60 Hex head screw bolt - mechanically galvanized M10 60 50 200
DfM1460300 10x75 Hex head screw bolt - mechanically galvanized M10 75 50 200
DfM1460330 10x100 Hex head screw bolt - mechanically galvanized M10 100 50 200
DfM1460360 10x110 Hex head screw bolt - mechanically galvanized M10 110 25 100
DfM1460390 10x120 Hex head screw bolt - mechanically galvanized M10 120 20 80
DfM1460420 10x140 Hex head screw bolt - mechanically galvanized M10 140 25 100
DfM1460450 10x160 Hex head screw bolt - mechanically galvanized M10 160 20 80
DfM1460480 10x200 Hex head screw bolt - mechanically galvanized M10 200 20 80
DfM1460510 10x240 Hex head screw bolt - mechanically galvanized M10 240 50 200
DfM1460540 10x280 Hex head screw bolt - mechanically galvanized M10 280 50 200
DfM1460570 10x320 Hex head screw bolt - mechanically galvanized M10 320 50 200
DfM1460600 12x75 Hex head screw bolt - mechanically galvanized M12 75 25 100
DfM1460630 12x100 Hex head screw bolt - mechanically galvanized M12 100 25 100
DfM1460660 12x150 Hex head screw bolt - mechanically galvanized M12 150 20 80
DfM1460690 12x200 Hex head screw bolt - mechanically galvanized M12 200 20 80
DfM1460720 16x100 Hex head screw bolt - mechanically galvanized M16 100 20 80
DfM1460750 16x130 Hex head screw bolt - mechanically galvanized M16 130 10 40
DfM1460780 16x150 Hex head screw bolt - mechanically galvanized M16 150 10 40
DfM1460810 16x200 Hex head screw bolt - mechanically galvanized M16 200 10 40
DfM1460840 16x240 Hex head screw bolt - mechanically galvanized M16 240 10 40
DfM1460870 16x280 Hex head screw bolt - mechanically galvanized M16 280 20 80
DfM1460900 16x320 Hex head screw bolt - mechanically galvanized M16 320 25 100
Blue-Tip (BT) Screw anchor - A4 stainless steel
DfM1430000 6x45 Hex head screw bolt - a4ss M6 45 100 400
DfM1430050 6x60 Hex head screw bolt - a4ss M6 60 100 800
DfM1430100 8x75 Hex head screw bolt - a4ss M8 75 50 200
DfM1430150 8x95 Hex head screw bolt - a4ss M8 95 50 200
DfM1430200 10x85 Hex head screw bolt - a4ss M10 85 50 200
DfM1430250 10x100 Hex head screw bolt - a4ss M10 100 50 200