M~.£~ 94-017 10_20_94 Order.pdfILLINOIS POLLUTION CONTROL BOARD October 20, 1994 IN THE MATTER OF:)...
107
ILLINOIS POLLUTION CONTROL BOARD October 20, 1994 IN THE MATTER OF: ) R94—17 RCRA UPDATE, USEPA REGULATIONS ) (Identical in Substance Rules) (1—1—94 THROUGH 6—30—94) ) Adopted Rule. Final Order. ORDER OF THE BOARD (by E. Dunham): Pursuant to Section 22.4(a) of the Environmental Protection Act (Act), the Board adopts amendments to the RCRA hazardous waste (RCRA) regulations. Section 22.4(a) provides for quick adoption of regulations that are “identical in substance” to federal regulations adopted by U.S. EPA to implement Sections 3001 through 3005 of the Resource Conservation and Recovery Act of 1976 (RCRA, 42 U.S.C. §S 6921—6925) and that Title VII of the Act and Section 5 of the Administrative Procedure Act (APA) shall not apply. Because this rulemaking is not subject to Section 5 of the APA, it is not subject to first notice or to second notice review by the Joint Committee on Administrative Rules (JCAR). The federal RCRA Subtitle C regulations are found at 40 CFR 260 through 268, 270 through 271, and, more recently, 279. This order is supported by an opinion adopted on the same day. The Board will file the adopted amendments 30 days after the date of this order. The complete text of the adopted rules follows. IT IS SO ORDERED. I, Dorothy N. Gunn, Clerk of the Illinois Pollution Control Board, do hereby certify that the ab ye or er was adopted by the Board on the c~°~ day of ____________, 1994, by a vote of ~—O. ~ M~. £~ Dorothy N. çifinn, Clef~k Illinois Pocflution Control Board
Transcript of M~.£~ 94-017 10_20_94 Order.pdfILLINOIS POLLUTION CONTROL BOARD October 20, 1994 IN THE MATTER OF:)...
ILLINOIS POLLUTION CONTROLBOARDOctober 20, 1994
IN THE MATTER OF: )R94—17
RCRA UPDATE, USEPA REGULATIONS ) (Identical in Substance Rules)(1—1—94 THROUGH6—30—94) )
Adopted Rule. Final Order.
ORDEROF THE BOARD (by E. Dunham):
Pursuant to Section 22.4(a) of the Environmental ProtectionAct (Act), the Board adopts amendments to the RCRAhazardouswaste (RCRA) regulations.
Section 22.4(a) provides for quick adoption of regulationsthat are “identical in substance” to federal regulations adoptedby U.S. EPA to implement Sections 3001 through 3005 of theResource Conservation and Recovery Act of 1976 (RCRA, 42 U.S.C.§S 6921—6925) and that Title VII of the Act and Section 5 of theAdministrative Procedure Act (APA) shall not apply. Because thisrulemaking is not subject to Section 5 of the APA, it is notsubject to first notice or to second notice review by the JointCommittee on Administrative Rules (JCAR). The federal RCRASubtitle C regulations are found at 40 CFR 260 through 268, 270through 271, and, more recently, 279.
This order is supported by an opinion adopted on the sameday. The Board will file the adopted amendments 30 days afterthe date of this order. The complete text of the adopted rulesfollows.
IT IS SO ORDERED.
I, Dorothy N. Gunn, Clerk of the Illinois Pollution ControlBoard, do hereby certify that the ab ye or er was adopted by theBoard on the c~°~ day of ____________, 1994, by a voteof ~—O.
~ M~.£~Dorothy N. çifinn, Clef~kIllinois Pocflution Control Board
2
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE G: WASTE DISPOSAL
CRAPPER I: POLLUTION CONTROLBOARDSUBCHAPTER b: PERMITS
PART 704UIC PERMIT PROGRAM
SUBPART A: GENERALPROVISIONSSection704.101 Content704.102 Scope of the Permit or Rule Requirement704.103 Identification of Aquifers704.104 Exempted Aquifers704.105 Specific Inclusions arid Exclusions704.106 Classification of Injection Wells704.107 Definitions
SUBPART B: PROHIBITIONSSection704.121 Prohibition of Unauthorized Injection704.122 Prohibition of Movement of Fluid into USDW704.123 Identification of USDWand Exempted Aquifers704.124 Prohibition of Class IV Wells
SUBPART C: AUTHORIZATION OF UNDERGROUNDINJECTION BY RULESection704.141 Existing Class I and III Wells704.142 Existing Class IV Wells, not into USDW(Renumbered)704.143 Expiration of Authorization704.144 Requirements704.145 Existing Class IV Wells704.146 Class V Wells704.147 Requiring a Permit704.148 Inventory Requirements704.149 Requiring other Information704.150 Requirements for Class I and III Wells authorized by Rule704.151 RCRA Interim Status for Class I Wells
SUBPARTD: APPLICATION FOR PERMITSection704.161 Application for Permit; Authorization by Permit704. 162 Area Permits704.163 Emergency Permits704.164 Signatories to Permit Applications
SUBPART B: PERMIT CONDITIONSSection704.181 Additional Conditions704. 182 Establishing UIC Permit Conditions704.183 Construction Requirements704.184 Corrective Action704.185 Operation Requirements704.186 Hazardous Waste Requirements704.187 Monitoring and Reporting704. 188 Plugging and Abandonment704.189 Financial Responsibility704.190 Mechanical Integrity704.191 Additional Conditions704.192 Waiver of Requirements by Agency704.193 Corrective Action
3
SUBPART F: REQUIREMENTSFOR WELLS INJECTING HAZARDOUSWASTESection704.201 Applicability704.202 Authorization704.203 Requirements
SUBPART G: FINANCIAL RESPONSIBILITY FOR CLASS IHAZARDOUSWASTE INJECTION WELLS
Section704.210 Applicability704.211 Definitions704.212 Cost Estimate for Plugging and Abandonment704.213 Financial Assurance for Plugging and Abandonment704.214 Trust Fund704.215 Surety Bond Guaranteeing Payment704.216 Surety Bond Guaranteeing Performance704.217 Letter of Credit704.218 Plugging and AbandonmentInsurance704.219 Financial Test and Corporate Guarantee704.220 Multiple Financial Mechanisms704.221 Financial Mechanism for Multiple Facilities704.222 Release of the Owner or Operator704.230 Incapacity704.240 Wording of the Instruments
SUBPART H: ISSUED PERMITSSection704.260 Transfer704.261 Modification704.262 Causes f or Modification704.263 Well Siting704.264 Minor Modifications
AUTHORITY: Implementing Sections 13 and 22.4 and authorized by Section 27 ofthe Environmental Protection Act (Ill. Roy. Stat. 1987, oh. ill 1/2, parc.1013, 1022.4 and 1027)1415 ILCS 5/13. 22.4, and 271.
SOURCE: Adopted in R81—32, at 47 PCB 95, at 6 Ill. Reg. 12479, effective asrioted in 35 Ill. Adm. Code 700.106; amended in R82-19, at 7 Iii. Reg. 14402,effective as noted in 35 Ill. Adni. Code 700.106; amended in R83-39, at 55 PCB319, at 7 Ill. Reg. 17338, effective December 19, 1983; amended in R85—23 at10 Ill. Reg. 13290, effective July 29, 1986; amended in R87—29 at 12 Iii. Reg.6687, effective March 28, 1988; amended in R88—2 at 12 Ill. Reg. 13700,effective August 16, 1988; amended in R88—17 at 13 Ill. Reg. 478, effectiveDecember 30, 1988; amended in R89—2 at Ill. Reg. 3116, effective February 20,1990; amended in R94—17 at Ill. Req. , effective
SUBPART G: FINANCIAL RESPONSIBILITY FOR CLASS I
HAZARDOUSWASTE INJECTION WELLS
Section 704.240 Wording of the Instruments
The Board incorporates by reference 40 CFR 144.70 (198S22j. as amended at 59Fed. Req. 29959 (June 10. 1994~. This incorporation includes no futureamendments or editions. The Agency will promulgate standarized forms based on40 CFR 144.70 with such changes in wording as are necessary under Illinoislaw. Any owner or operator required to establish financial assurance underthis Subpart shall do so only upon the standarized forms promulgated by theAgency. The Agency may reject any financial assurance document whichthat isnot submitted on such standardized forms.
4
~BoardOARD Ne~eO~: SeeDerived from 40 CFR 144.70 (1992), as amendedat 59Fed. Req. 29959 (June 10, 1994).-)-
(Source: Amended at Ill. Req. _________, effective
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE G: WASTE DISPOSAL
CHAPTER I: POLLUTION CONTROLBOARDSUBCHAPTER C: HAZARDOUSWASTEOPERATING REQUIREMENTS
PART 720HAZARDOUSWASTE MANAGEMENTSYSTEM: GENERAL
SUBPARTA: GENERALPROVISIONSSect ion720.101 Purpose, Scope and Applicability720.102 Availability of Information; Confidentiality of Information720.103 Use of Number and Gender
SUBPART B: DEFINITIONSSect ion720.110 Definitions720.111 References
SUBPART C: RULEMAKINGPETITIONS AND OTHER PROCEDURESSection720 • 120 Rulemaking720.121 Alternative Equivalent Testing Methods720.122 Waste Deliating720.130 Procedures for Solid Waste Determinations720.131 Solid Waste Determinations720.132 Boiler Determinations720.133 Procedures for Determinations720.140 Additional regulation of certain hazardous waste Recycling
Activities on a case-by—caseBasis720.141 Procedures for case—by—caseregulation of hazardous waste
Recycling Activities
72O.Appondix A Overview of 40 CFR, Subtitle C Regulations
AUTHORITY: Implementing Section 22.4 and authorized by Section 27 of theEnvironmental Protection Act (Ill. Rov~ Stat. 1991, oh. 111½, parc.- 1022.4 and1027 (415 ILCS 5/22.4 and 271+.
SOURCE: Adopted in R81—22, 43 PCB 427, at 5 Ill. Req. 9781, effective asnoted in 35 Ill. Adm. Code 700.106; amended and codified in R81-22, 45 PCB317, at 6 Ill. Req. 4828, effective as noted in 35 Ill. Adxn. Code 700.106;amended in R82—19 at 7 Iii. Reg. 14015, effective October 12, 1983; amended inR84—9, 53 PCB 131 at 9 Ill. Req. 11819, effective July 24, 1985; amended inR85—22 at 10 Xli. Req. 968, effective January 2, 1986; amended in R86—1 at 10Ill. Reg. 13998, effective August 12, 1986; amended in R86—19 at 10 Ill. Reg.20630, effective December 2, 1986; amended in R86—28 at 11 Ill. Req. 6017,effective March 24, 1987; amended in R86—46 at 11 Ill. Reg. 13435, effectiveAugust 4, 1987; amended in R87—5 at 11 Ill. Req. 19280, effective November 12,1987; amended in R87—26 at 12 Ill. Reg. 2450, effective January 15, 1988;amended in R87—39 at 12 Ill. Reg. 12999, effective July 29, 1988; amended inR88—l6 at 13 Ill. Reg. 362, effective December 27, 1988; amended in R89—1 at13 Ill. Rag. 18278, effective November 13, 1989; amended in R89—2 at 14 Ill.Reg. 3075, effective February 20, 1990; amended in R89—9 at 14 Ill. Req. 6225,effective April 16, 1990; amended in R90—10 at 14 Ill. Req. 16450, effective
5
September 25, 1990; amended in R90-17 at 15 Ill. Reg. 7934, effective May 9,1991; amended in R90—11 at 15 Ill. Reg. 9323, effective June 17, 1991; amendedin R91—1 at 15 Ill. Req. 14446, effective September 30, 1991; amended in R9l—13 at 16 Ill. Reg. 9489, effective June 9, 1992; amended in R92—1 at 16 Iii.Req. 17636, effective November 6, 1992; amended in R92-10 at 17 Iii. Reg.5625, effective March 26, 1993; amended in R93—4 at 17 Ill. Req. 20545,effective November 22, 1993; amended in R93—16 at 18 Ill. Req. 6720, effectiveApril 26, 1994; amended in R94-7 at 18 ILl. Req. 12160, effective July 29,1994; amended in R94—17 at Ill. Req. , effective
SUBPART B: DEFINITIONS
Section 720.111 References
a) The following publications are incorporated by reference:
ANSI. Available from the American National StandardsInstitute, 1430 Broadway, New York, New York 10018, +2123—~354—33O0:
ANSI 831.3 and B31.4. See ASME/ANSI 831.3 and B31.4
ACI. Available from the American Concrete Institute, Box19150, Redford Station, Detroit, Michigan 48219:
ACI 318-83: “Building Code Requirements forReinforced Concrete”, adopted September, 1983.
API. Available from the American Petroleum Institute, 1220L Street, N.W., Washington, D.C. 20005, .f2O2-)—~682—8OOO:
“Guide for Inspection of Refinery Equipment, ChapterXIII, Atmospheric and Low Pressure Storage Tanks,” 4thEdition, 1981, reaffirmed December, 1987.
“Cathodic Protection of Underground Petroleum StorageTanks and Piping Systems,” API Recommended Practice1632, Second Edition, December, 1987.
“Installation of Underground Petroleum StorageSystems,” API Recommended Practice 1615, FourthEdition, November, 1987.
APTI. Available from the Air and Waste ManagementAssociation, Box 2861, Pittsburgh, PA 15230, +412-)---232—3444:
APTI Course 415: Control of Gaseous Emissions, U.S.EPA Publication EPA—450/2—8l—005, December, 1981.
ASME. Available from the American Society of Mechanical.Engineers, 345 East 47th Street, New York, NY 10017, +212+~705—7722:
“Chemical Plant and Petroleum Refinery Piping”, ASME/ANSI B31.3—1987, as supplemented by B31..3a—1988 andB31.3b-1988. Also available from ANSI.
“Liquid Transportation Systems for Hydrocarbons,Liquid Petroleum Gas, Anhydrous Ammonia, and
6
Alcohols”, ASME/ANSI B31.4-1986, as supplemented byB31.4a—1987, Also available from ANSI.
ASTM. Available from American Society for Testing andMaterials, 1916 Race Street, Philadelphia, PA 19103, +215+—.~299—5400:
ASTM C94-90, Standard Specification for Ready-MixedConcrete, approved March 30, 1990.
ASTK D88-87, Standard Test Method for SayboltViscosity, April 24, 1981, reapproved January, 1987.
ASTM D93—85, Standard Test Methods for Flash Point byPensky—Martens Closed Tester, approved October 25,1985.
ASTM D1946—90, Standard Practice for Analysis ofReformed Gas by Gas Chromatography, Approved March 30,1990.
ASTM D2161-87, Standard Practice for Conversion ofKinematic Viscosity to Saybolt Universal or to SayboltFurol Viscosity, March 27, 1987.
ASTM D2267-88, Standard Test Method for Aromatica inLight Naphthas and Aviation Gasolines by GasChromatography, approved November 17, 1988.
ASTM D2382—88, Standard Test Method for Heat ofCombustion of Hydrocarbon Fuels by Bomb Calorimeter(High Precision Method), approved October 31, 1988.
AST4 D2879-86, Standard Test Method for VaporPressure-Temperature Relationship and InitialDecomposition Temperature of Liquids by Isoteniscope,approved October 31, 1986.
ASTMD3828-87, Standard Test Methods for Flash Pointof Liquids by Setaf lash Closed Tester, approvedDecember 14, 1988.
ASTM E168—88, Standard Practices for GeneralTechniques of Infrared Quantitative Analysis, approvedMay 27, 1988.
ASTM E169—87, Standard Practices for GeneralTechniques of Ultraviolet—Visible QuantitativeAnalysis, approved February 1, 1987.
ASTM E260—85, Standard Practice for Packed Column GasChromatography, approved June 28, 1985.
ASTM E926-88 C, Standard Test Methods for PreparingRefuse-Derived Fuel (RDP) Samples for Analysis ofMetals, Bomb—Acid Digestion Method, approved March 25,1988.
ASTM Method G21—70 (l984a) —- Standard Practice forDetermining Resistance of Synthetic Polymer Materialsto Fungi
7
ASTMMethod G22—76 (l984b) —- Standard Practice forDetermining Resistance of Plastics to Bacteria.
GPO. Available from the Superintendent of Documents, U.S.Government Printing Office, Washington, D.C. 20402, +202-783—3238-)-:
Standard Industrial Classification Manual (1972), and1977 Supplement, republished in 1983
“Test Methods for Evaluating Solid Waste, Physical!Chemical Methods,” U.S. EPA Publication number SW-846(Third Edition, Scpt~Q~ember~1986), as amended byUpdate~ I and IIA (July 1~-92) (Document Number 955—001—00000—1) (contact U.S. EPA, Office of Solid Waste,or MICE. as indicated below, for Update hA).
MICE. Available from Methods Information CommunicationService, at 703—821—4789:
“Test Methods for Evaluating Solid Waste. Phvai.cal/Chemical Methods,” U.S. EPA Publication number SW—846(Third Edition, November, 1986), Update hA (Document
Number 955—001—00000—1) (contact GPO, as indicatedabove, for SW—846 and Update I’j.
NACE. Available from the National Association of CorrosionEngineers, 1400 South Creek Dr., Houston, TX 77084, +713+—~492—0535:
“Control of External Corrosion on Metallic Buried,Partially Buried, or Submerged Liquid StorageSystems”, NACE Recommended Practice RP0285—85,approved March, 1985.
NFPA. Available from the National Fire ProtectionAssociation, Batterymarch Park, Boston, MA 02269, -(-617-)--z770-3000 or +800-)--344—3555:
“Flammable and Combustible Liquids Code” NFPA 30,issued July 17, 1987. Also available from ANSI.
NTIS. Available from the U.S. Department of Commerce,National Technical Information Service, 5285 Port RoyalRoad, Springfield, VA 22161, -�7O3+—z487—4600:
“Generic Quality Assurance Project Plan for LandDisposal Restrictions Program”, EPA/530—SW—87—011,March 15, 1987. (Document number PB 88—170766.)
“Guidance on Air Quality Models”, Revised 1986.(Document number PB86-245—248 (Guideline) and PB88—150—958 (Supplement>).
“Methods for Chemical Analysis of Water and Wastes”,Third Edition, March, 1983. (Document number PS 84-128677).
“Methods Manual for Compliance with BIF Regulations”,December, 1990. (Document number PB91—120-006).
“Petitions to Delist Hazardous Wastes —— A Guidance
8
Manual”, EPA/530—SW—85-003, April, 1985. (DocumentNumber PB 85—194488).
“Procedures Manual for Ground Water Monitoring atSolid Waste Disposal Facilities”, EPA—530/SW—611,1977. (Document number PB 84—174820).
“Screening Procedures for Estimating the Air QualityImpact of Stationary Sources”, October, 1992,Publication Number EPA—450/R—92—019.
STI. Available from the Steel Tank Institute, 728 AnthonyTrail, Northbrook, IL 60062, (312)- 708—498—1980:
“Standard for Dual Wall Underground Steel StorageTanks” (1986).
U.S. EPA. Available from United States EnvironmentalProtection Agency, Office of Drinking Water, State ProgramsDivision, WH 550 E, Washington, D.C. 20460:
“Technical Assistance Document: Corrosion, ItsDetection and Control in Injection Wells”, EPA 570/9-87—002, August, 1987.
U.S. EPA. Available from U.S. EPA, Office of Solid Waste(Mail Code 5304), 401 N Street SW, Washington, D.C. 20460:
“Test Methods for Evaluating Solid Waste, Physical!Chemical Methods,” U.S. EPA Publication number SW—846(Third Edition. November, 1986), Update hA (DocumentNumber 955—001—00000--i) (contact GPO, as indicatedabove, for SW—846and Update IL.
U.S. EPA. Available from U.S. EPA, Number F-90-WPWF-FFFFF,Room M2427, 401 M Street SW, Washington, D.C. 20460, +202+z475—9327:
“Test Method 8290: Procedures for the Detection andMeasurement of PCDDGand PCDFe”, EPA/530—SW—91—019(January, 1991)
U.S. EPA. Available from Receptor Analysis Branch, U.S. EPA(MD—14), Research Triangle Park, NC 27711:
“Screening Procedures for Estimating the Air QualityImpact of Stationary Sources, Revised”, October, 1992,Publication Number EPA—450/R—92’-019.
b) Code of Federal Regulations. Available from the Superintendent ofDocuments, U.S. Government Printing Office, Washington, D.C.20401, +2O2-)—~783—3238:
10 CFR 20, Appendix B (1992)
40 CFR 51.100(u) (1992)
40 CFR 51, Subpart W, as added at 58 Fed, Reg. 38822 (July20, 1993)
40 CPA 60 (1993)
9
40 CPA 61, Subpart V (1993)
40 CPA 136 (1993)
40 CPA 142 (1993)
40 CFR 220 (1992)
40 CPA 260.20 (1992)
40 CPA 264 (1992)
40 CPA 268.Appendix IX (1992)
40 CFR 302.4, 302.5 and 302.6 (1992)
40 CPA 761 (1993)
C) Federal Statutes
Section 3004 of the Resource Conservation and Recovery Act (42U.S.C. 6901 et seq.), as amended through December 31, 1987.
d) This Section incorporates no later edi.tions or amendments.
(Source: Amended at _____ Ill. Reg. _________, effective
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE G: WASTE DISPOSAL
CHAPTER I: POLLUTION CONTROL BOARDSUBCHAPTER c: HAZARDOUS WASTE OPERATING REQUIREMENTS
PART 721IDENTIFICATION AND LISTING OP HAZARDOUS WASTE
SUBPART A: GENERAL PROVISIONSSection721.101 Purpose and Scope721.102 Definition of Solid Waste721.103 Definition of Hazardous Waste721.104 Exclusions721.105 Special Requirements for Hazardous Waste Generated by Small
Quantity Generators721.106 Requirements for Recyclable Materials721.107 Residues of Hazardous Waste in Empty Containers721.108 PCB Wastes Regulated under TSCA
SUBPART B: CRITERIA FOR IDENTIFYING THE CHARACTERISTICSOP HAZARDOUS WASTE AND FOR LISTING HAZARDOUSWASTES
Section721.110 Criteria for Identifying the Characteristics of Hazardous Waste721.111 Criteria for Listing Hazardous Waste
SUBPART C: CHARACTERISTICS OF HAZARDOUSWASTESection721.120 General721.121 Characteristic of Ignitability721.122 Characteristic of Corrosivity721.123 Characteristic of Reactivity721.124 Toxicity Characteristic
10
SUBPARTU: LISTS OF HAZARDOUSWASTESect ion721.130 General721.131 Hazardous Wastes From Nonspecific Sources721.132 Hazardous Waste from Specific Sources721.133 Discarded Commercial Chemical Products, Off—Specification Species,
Container Residues4~ and Spill Residues Thereof721.135 Wood Preserving Wastes
721.Appendix A Representative Sampling Methods721.Appendix B Method 1311 Toxicity Characteristic Leaching Procedure
(TCLP)72l.Appendix C Chemical Analysis Test Methods
Table A Analytical Characteristics of Organic Chemicals (Repealed)Table B Analytical Characteristics of Inorganic Species (Repealed)Table C Sample Preparation/Sample Introduction Techniques (Repealed)
721Appendix G Basis for Listing Hazardous Wastes721.Appendix H Hazardous Constituents721.Appendix I Wastes Excluded under Section 720.120 and 720.122
Table A Wastes Excluded from Non—Specific SourcesTable B Wastes Excluded from Specific SourcesTable C Wastes Excluded Prom Commercial Chemical Products, Of f—
Specification Species, Container Residues, and Soil ResiduesThereof
Table U Wastes Excluded by Adjusted Standard721.Appendix .1 Method of Analysis for Chlorinated Dibenzo-p-Dioxins and
Dibenzofurans (Repealed)721.Appendix Z Table to Section 721.102
AUTHORITY: Implementing Section 22.4 and authorized by Section 27 of theEnvironmental Protection Act (Ill. Rev. Stat. 1991, oh. 11i~, parc. 1022.4 and1027 (415 ILCS 5/22.4 and 27]+.
SOURCE: Adopted in R81—22, 43 PCB 427, at 5 Ill. Req. 9781, effective asnoted in 35 Ill. Adm. Code 700.106; amended and codified in R81—22, 45 PCB317, at 6 Ill. Reg. 4828, effective as noted in 35 Ill. Adm. Code 700.106;amended in R82—18, 51 PCB 31, at 7 Ill. Req. 2518, effective February 22,1983; amended in R82—19, 53 PCB 131, at 7 Ill. Req. 13999, effective October12, 1983; amended in R84—34, 61 PCB 247, at B Ill. Req. 24562, effectiveDecember 11, 1984; amended in R84—9, at 9 Ill. Req. 11834, effective July 24,1985; amended in R85—22 at 10 Ill. Req. 998, effective January 2, 1986;amended in R85—2 at 10 Ill. Reg. 8112, effective May 2, 1986; amended in R86—1at 10 Ill. Req. 14002, effective August 12, 1986; amended in R86—19 at 10 Ill.Reg. 20647, effective December 2, 1986; amended in R86—28 at 11 Ill. Aeg.6035, effective March 24, 1987; amended in R86—46 at 11 Ill. Reg. 13466,effective August 4, 1987; amended in R87—32 at 11 Ill. Req. 16698, effectiveSeptember 30, 1987; amended in R87-5 at ii. Ill. Reg. 19303, effective November12, 1987; amended in R87—26 at 12 Ill, Reg. 2456, effective January 15, 1988;amended in R87-30 at 12 Ill. Reg. 12070, effective July 12, 1988; amended inR87—39 at 12 Ill. Reg. 13006, effective July 29, 1988; amended in R88—16 at 13Ill. Req. 382, effective December 27, 1988; amended in R89—1 at 13 Ill. Req.18300, effective November 13, 1989; amended in R90—2 at 14 Ill. Req. 14401,effective August 22, 1990; amended in R90—1Oat 14 Ill. Reg. 16472, effectiveSeptember25, 1990; amended in R90—17 at 15 Ill. Reg. 7950, effective Nay 9,1991; amended in R90—11 at 15 Ill. Req. 9332, effective June 17, 1991; amendedin R91—1 at 15 Iii. Req. 14473, effective September 30, 1991; amended in R91—12 at 16 Ill. Req. 2155, effective January 27, 1992; amended in R91—26 at 16Ill. Reg. 2600, effective February 3, 1992; amended in R91—13 at 16 Ill. Reg.9519, effective June 9, 1992; amended in R92—1 at 16 Iii. Reg. 17666,effective November 6, 1992; amended in R92—10 at 17 Ill. Req. 5650, effectiveMarch 26, 1993; amended in R93—4 at 17 Ill. Req. 20568, effective November 22,1993; amended in R93—16 at 18 Ill. Reg. 6741, effective April 26, 1994;
11
:nded in R94-7 at 18 Ill. Req. 12175, effective July 29. 1994; amended in
R94—17 at Ill. Rep. , effective
SUBPARTA: GENERALPROVISIONS
Section 721.104 Exclusions
a) Materials whichthat are not solid wastes. The following materialsare not solid wastes for the purpose of this Part:
1) Sewage:
A) Domestic sewage; and
8) Any mixture of domestic sewage and other waste thatpasses through a sewer system to publicly—ownedtreatment works for treatment. “Domestic sewage”means untreated sanitary wastes that pass through asewer system.
2) Industrial wastewater discharges that are point sourcedischarges with NPDES permits issued by the Agency pursuantto Section 12(f) of the Environmental Protection Act and 35Ill. Adxn. Code 309.
BOARD NOTE: This exclusion applies only to the actual pointsource discharge. It does not exclude industrialwastewatere while they are being collected, stored~ ortreated before discharge, nor does it exclude sludges thatare generated by industrial wastewater treatment.
3) Irrigation return flows.
4) Source, special nuclear2 or by—product material as definedby the Atomic Energy Act of 1954, as amended (42 U.S.C. 2011et seq.)
5) Materials subjected to in-situ mining techniques wh4~ehthatare not removed from the ground as part of the extractionprocess.
6) Pulping liquors (i.e., black liquor) that are reclaimed in apulping liquor recovery furnace and then reused in thepulping process, unless accumulated speculatively as definedin Section 721.1Ol(c)-t-~.
7) Spent sulfuric acid used to produce virgin sulfuric acid,unless it is accumulated speculatively as defined in Section721.101(c).
8) Secondary materials that are reclaimed and returned to theoriginal process or processes in which they were generatedwhere they are reused in the production process, provided:
A) Only tank storage is involved, and the entire processthrough completion of reclamation is closed by beingentirely connected with pipes or other comparableenclosed means of conveyance;
B) Reclamation does not involve controlled flamecombustion (such as occurs in boilers, industrial
12
furnaces or incinerators);
C) The secondary materials are never accumulated in suchtanks for over twelve months without being reclaimed;and
U) The reclaimed material is not used to produce a fuel,or used to produce products that are used in a mannerconstituting disposal.
9) Wood preserving wastes.
A) Spent wood preserving solutions that have been usedand are reclaimed and reused for their originalintended purpose; and
B) Wastewaters from the wood preserving process that havebeen reclaimed arid are reused to treat wood.
10) Hazardous waste number 1(060, 1(087, 1(141, 1(142, 1(143, 1(144,1(145, K147, and 1(148, and any wastes from the coke by-products processes whichthat are hazardous only because theyexhibit the toxicity characteristic specified in Section721.124, when, subsequent to generation, these materials arerecycled to coke ovens, to the tar recovery process as afeedatock to produce coal tar~ or are mixed with coal tarprior to the tar’s sale or refining. This exclusion isconditioned on there being no land disposal of the wastesfrom the point they are generated to the point they arerecycled to coke ovens or tar recovery or the tar refiningprocesses, or mixed with coal.
11) Nonwastewater splash condenser dross residue from thetreatment of 1(06]. in high temperature metals recovery units,provided it is shipped in drums (if shipped) and not landdisposed before recovery.
b) Solid wastes whichthat are not hazardous wastes. The followingsolid wastes are not hazardous wastes:
1) Household waste, including household waste that has beencollected, transported, stored, treated, disposed, recovered(e.g., refuse—derived fuel)4, or reused. “Household waste”
means any waste material (including garbage, trash~, andsanitary wastes in septic tanks) derived from households(including single and multiple residences, hotels4, andmotels, bunkhouses, ranger stations, crew quarters,campgrounds, picnic grounds4, and day—use recreation areas).A resource recovery facility managing municipal solid wasteshall not be deemed to be treating, storing, disposing of4,or otherwise managing hazardous wastes for the purposes ofregulation under this Part, if such facility:
A) Receives and burns only:
i) Household waste (from single and multipledwellings, hotels, motels4, and other residentialsources) and
ii) Solid waste from commercial or industrialsources that does not contain hazardous waste;and
13
B) Such facility does not accept hazardous waste and theowner or operator of such facility has establishedcontractual requirements or other appropriatenotification or inspection procedures to assure thathazardous wastes are not received at or burned in suchfacility.
BOARD NOTE: The U.S. Supreme Court determined, inCity of Chicago v. Envronmental Defense Fund, Inc.,no. 92—1639 (May 2, 1994~. that this exclusion andRCRA section 3001(il (42 U.S.C. S 6921(ifl do notexclude the ash from facilities covered by thissubsection from regulation as a hazardous waste. At59 Fed. Req. 29372 (June 7, 1994~, U.S. EPA arantedfacilities managing ash from such facilities that isdetermined a hazardous waste under 721.Subpart C untilDecember 7, 1994 to file a Part A permit applicationpursuant to 35 Ill. Adm. Code 703.181.
2) Solid wastes generated by any of the following and whiohthatare returned to the soil as fertilizers:
A) The growing and harvesting of agricultural crops.
8) The raising of animals, including animal manures.
3) Mining overburden returned to the mine site.
4) Ply ash waste, bottom ash waste, slag waste4, and flue gasemission control waste generated primarily from thecombustion of coal4, or other fossil fuels, except asprovided in 35 Ill, Adm. Code 726.212 for facilities thatburn or process hazardous waste.
5) Drilling fluids, produced waters, and other wastesassociated with the exploration, development, or productionof crude oil, natural gas4, or geothermal energy.
6) Chromium wastes:
A) Wastes ~.~ihichthat fail the test for the toxicitycharacteristic (Sections 721.124 and 721.Appendix B)because chromium is present or which are are listed inSubpart U of this Part due to the presence ofchromium, whichthat do not fail the test for thetoxicity characteristic for any other constituent orwhich are not listed due to the presence of any otherconstituent, and uhiohthat do not fail the test forany other characteristic, if it is shown by a wastegenerator or by waste generators that:
i) The chromium in the waste is exclusively (ornearly exclusively) trivalent chromium; and
ii) The waste is generated from an industrialprocess whichthat uses trivalent chromiumexclusively (or nearly exclusively) and theprocess does not generate hexavalent chromium;and
iii) The waste is typically and frequently managed innon—oxidizing environments.
14
B) Specific wastes whiohthat meet the standard insubsections (b)(6)(A)(i), (b)(6~(A)(ii)4, and(b~(6~(A~(iii),- above,- (so long as they do not failthe test for the toxicity characteristic for any otherconstituent and do not exhibit any othercharacteristic) are:
i) Chrome (blue) trimmings generated by thefollowing subcategories of the leather tanningand finishing industry; hair pulp/chrometan/retan/wet finish; hair save/chrometan/retari/wet finish; retan/wet finish; nobeanthouse; through—the—blue; and shearling.
ii) Chrome (blue) shavings generated by thefollowing subcategories of the leather tanningand finishing industry; hair pulp/chrometan/retan/wet finish; hair save/chrometan/retan/wet finish; retan/wet finish; nobeambouse; through—the—blue; and shearling.
Lii) Buffing dust generated by the followingsubcategories of the leather tanning andfinishing industry: hair pulp/chrometan/retan/wet finish; hair save/chrometan/retan/wet finish; retan/wet finish; nobeamhouse; through—the-blue.
iv) Sewer screenings generated by the followingsubcategories of the leather tanning andfinishing industry: hair pulp/chrometan/retan/wet finish; hair save/chrometan/retan/wet finish; retan/wet finish; nobeaxnhouse;through—the—blue; and shearling.
v) Wastewater treatment sludges generated by thefollowing subcategories of the leather tanningand finishing industry: hair pulp/chrometan/retan/wet finish; hair save/chrometan/retan/wet finish; retan/wet finish; nobeanthouse; through-the-blue; and shearling.
vi) Wastewater treatment sludges generated by thefollowing subcategories of the leather tanningand finishing industry: hair pulp/chrometan/retan/wet finish; hair save/chrometan/retan/wet finish; and through—the—blue.
vii) Waste scrap leather from the leather tanningindustry, the shoe manufacturing industry, andother leather product manufacturing industries.
viii) Wastewater treatment sludges from the productionof titanium dioxide pigment using chromium—bearing ores by the chloride process.
7) Solid waste from the extraction, beneficiation4, andprocessing of ores and minerals (including coal, phosphaterock4, and overburden from the mining of uranium ore), exceptas provided by 35 Ill. Adm. Code 726.212 for facilities thatburn or process hazardous waste. For purposes of thissubsection, beneficiation of ores and minerals is restricted
15
to the following activities: crushing, grinding, washing,dissolution, crystallization, filtration, sorting, sizing,drying, siritering, pelletizing, briquetting, calcining toremove water or carbon dioxide, roasting, autoclaving orchlorination in preparation for leaching (except where theroasting or autoclaving or chlorination.)-t arid leachingsequence produces a final or intermediate product that doesnot undergo further beneficiation or processing), gravityconcentration, magnetic separation, electrostaticseparation, floatation, ion exchange, solvent extraction,electrowinning, precipitation, amalgamation, and heap, dump,vat tank4, and in situ leaching. For the purposes of thissubsection, solid waste from the processing of ores andminerals includes only the following wastes:
A) Slag from primary copper processing;
B) Slag from primary lead processing;
C) Red and brown muds from bauxite refining;
D) Phosphogypsum from phosphoric acid production;
E) Slag from elemental phosphorus production;
F) Gasifier ash from coal gasification;
G) Process wastewater from coal gasification;
H) Calcium sulfate wastewater treatment plant sludge fromprimary copper processing;
I) Slag tailings from primary copper processing;
Fluorogypsum from hydrofluoric acid production;
K) Process wastewater from hydrofluoric acid production;
L) Air pollution control dust7~ or sludge from iron blast
furnaces;
N) Iron blast furnace slag;
N) Treated residue from roasting~ and leaching of chromeore;
0) Process wastewater from primary magnesium processingby the anhydrous process;
P) Process wastewater from phosphoric acid production;
Q) Basic oxygen furnace and open hearth furnace airpollution control dust~L or sludge from carbon steelproduction;
H) Basic oxygen furnace and open hearth furnace slag fromcarbon steel production;
S) Chloride processing waste solids from titaniumtetrachloride production; and,
T) Slag from primary zinc smelting.
16
8) Cement kiln dust waste, except as provided by 35 Ill. Mm.Code 726.212 for facilities that burn or process hazardouswaste.
9) Solid waste whichthat consists of discarded arsenical—treated wood or wood products which fails the test for thetoxicity characteristic for hazardous waste codes D004through D017 and whiohthat is not a hazardous waste for anyother reason if the waste is generated by persons whoutilize the arsenical—treated wood and wood products forthese materials’ intended end use.
10) Petroleum-contaminated media and debris that fail the testfor the toxicity characteristic of Section 721.124(hazardous waste codes 0018 through D043 only) and aresubject to corrective action regulations under 35 Ill. Mm.Code 731.
11) Injected groundwater that is hazardous only because itexhibits the toxicity characteristic (U.S. EPA hazardouswaste codes D018 through D024 only) in Section 721.124 thatis reinjected through an underground injection well pursuantto free phase hydrocarbon recovery operations undertaken atpetroleum refineries, petroleum marketing terminalspetroleum bulk plants, petroleum pipelines4, and petroleumspill sites until January 25, 1993. This extension appliesto recovery operations in existence, or for which contractshave been issued, on or before March 25, 1991. Forgroundwater returned through infiltration galleries fromsuch at petroleum refineries, marketing terminals4, and bulkplants, until October 2, 1991. New operations involvinginjection wells (beginning after March 25, 1991) willqualify for this compliance date extension (until January25, 1993) only if:
A) Operations are performed pursuant to a “free productremoval report” pursuant to 35 Iii. Mm. Code 731.164;and
B) A copy of the “free product removal report” has beensubmitted to:
Characteristics Section (08-333)U.S. EPA401 M Street, SWWashington, D.C. 20460
12) Used chlorofluorocarbon refrigerants from totally enclosedheat transfer equipment, including mobile air conditioningsystems, mobile refrigeration, and commercial and industrialair conditioning and refrigeration systems, whi-chthat usechlorofluorocarbons as the heat transfer fluid in arefrigeration cycle, provided the refrigerant is reclaimedfor further use.
13) Non—terne plated used oil filters whiohthat are not mixedwith wastes listed in Subpart D of this Part, if these oilfilters have been gravity hot—drained using one of thefollowing methods:
A) Puncturing the filter anti-drain back valve or thefilter dome end and hot-draining;
17
B) Hot-draining and crushing;
C) Dismantling and hot-draining; or,
D) Any other equivalent hot-draining method whichthatwill remove used oil.
14) Used oil re-refining distillation bottoms that are used asfeedstock to manufacture asphalt products.
C) Hazardous wastes whiahthat are exempted from certain regulations.A hazardous waste whichthat is generated in a product or rawmaterial storage tank, a product or raw material transport vehicleor vessel, a product or raw material pipeline, or in amanufacturing process unit4, or an associated non—waste—treatmentmanufacturing unit, is not subject to regulation under 35 Ill.Adm. Code 702, 703, 7054, and 722 through 725 and 728 or to thenotification requirements of Section 3010 of RCHA until it exitsthe unit in which it was generated, unless the unit is a surfaceimpoundment, or unless the hazardous waste remains in the unitmore than 90 days after the unit ceases to be operated formanufacturing, or for storage or transportation of product or rawmaterials.
d) Samples
1) Except as provided in subsection (d)(2) below, a sample ofsolid waste or a sample of water, soil4, or air,- whichthat iscollected for the sole purpose of testing to determine itscharacteristics or composition,- is not subject to anyrequirements of this Part or 35 Ill. Mm. Code 702, 703,7054, and 722 through 728. The sample qualifies when:
A) The sample is being transported to a laboratory forthe purpose of testing; or
B) The sample is being transported back to the samplecollector after testing; or
C) The sample is being stored by the sample collectorbefore transport to a laboratory for testing; or
D) The sample is being stared in a laboratory beforetesting; or
E) The sample is being stored in a laboratory for testingbut before it is returned to the sample collector; or
F) The sample is being stored temporarily in thelaboratory after testing for a specific purpose (forexample, until conclusion of a court case orenforcement action where further testing of the samplemay be necessary).
2) In order to qualify for the exemption in aubsection~(d)(1)(A) and (d)(1)(B) above, a sample collector shippingsamples to a laboratory and a laboratory returning samplesto a sample collector mu~tshall:
A) Comply with U.S. Department of Transportation (DOT),U.S. Postal Service (USPS)4, or any other applicableshipping requirements; or
18
B) Comply with the following requirements if the samplecollector determines that DOT, USFS4, or other shippingrequirements do not apply to the shipment of thesample:
i) Assure that the following informationaccompanies the sample: The sample collector’sname, mailing address4, and telephone number; thelaboratory’s name, mailing address4, andtelephone number; the quantity of the sample;the date of the shipment; and a description ofthe sample.
ii) Package the sample so that it does not leak,spill4, or vaporize from its packaging.
3) This exemption does not apply if the laboratory determinesthat the waste is hazardous but the laboratory is no longermeeting any of the conditions stated in subsection {d)(1)above.
e) Treatability study samples.
1) Except as is provided in subsection (e)(2) below, personswho generate or collect samples for the purpose ofconducting treatability studies, as defined in 35 Ill. Adm.Code 720.110, are not subject to any requirement of 35 Ill.Adm. Code 721 through 723 or to the notificationrequirements of Section 3010 of the Resource Conservationand Recovery Act. Nor are such samples included in thequantity determinations of Section 721.105 and 35 Ill. Adm.Code 722.134(d) when:
A) The sample is being collected and prepared fortransportation by the generator or sample collector;or,
B) The sample is being accumulated or stored by thegenerator or sample collector prior to transportationto a laboratory or testing facility; or
C) The sample is being transported to the laboratory ortesting facility for the purpose of conducting atreatability study.
2) The exemption in subsection (e)(1) above is applicable tosamples of hazardous waste being collected and shipped forthe purpose of conducting treatability studies providedthat:
A) The generator or sample collector uses (in“treatability studies”) no more than 10,.QOO kg ofa~ymedia contaminated with non—acute hazardous waste,1000 kg of non—acute hazardous waste other thancontaminated media, 1 kg of acute hazardous waste4, or250Q kg of coilo, uatcr or dobriomedia contaminatedwith acute hazardous waste for each process beingevaluated for each generated wastestream; and
B) The mass of each shipment does not exceed 1O4,Q00 kgj.the 10,000 ka cruantity may be all media contaminatedwith e#.—non—acute hazardous waste, or may include 2500
19
kg of media contaminated with acute hazardous waste,1000 kg of hazardouswaste, and 1 kg of acutehazardous waste or 250- kg-of coilo, wator -or dobriaoontaminatod with ziouto hazardouc waoto and
C) The sample must be packagedso that it does not leak,spill4, or vaporize from its packaging during shipmentand the requirements of subsections (e)(2)(C)(i) or(eI(2I(C~(ii), below, are met.
I) The transportation of each sample shipmentcomplies with U.S. Department of Transportation(DOT), U.S. Postal Service (USFS)4, or any otherapplicable shipping requirements; or
ii) It the DOT, USFS4, or other shipping requirementsdo not apply to the shipment of the sample, thefollowing information must accompany the sample:The name, mailing address4, and telephone numberof the originator of the sample; the name,address4, and telephone number of the facilitythat will perform the treatability study; thequantity of the sample; the date of theshipment; and, a description of the sample,including its U.S. EPA hazardous waste number.
U) The sample is shipped to a laboratory or testingfacility whichthat is exempt under subsection (f)below, or has an appropriate RCRA permit or interimstatus.
B) The generator or sample collector maintains thefollowing records for a period ending 3 years aftercompletion of the treatability study:
i) Copies of the shipping documents;
ii) A copy of the contract with the facility
conducting the treatability study;
iii) Documentation showing: The amount of wasteshipped under this exemption; the name, address4,and U.S. EPA identification number of thelaboratory or testing facility that received thewaste; the date the shipment was made; and,whether or not unused samples and residues werereturned to the generator.
F) The generator reports the information required insubsection (e)(2)(E)(iii) above in its report under 35Ill. Adm. Code 722.141.
3) The Agency may grant requests on a case—by-case basis for upto an additional two years for treatability studie~involving bioremediation. The Agency may grant requests, ona case—by—case basis, for quantity limits in excess of thosespecified in subsection (e)(2)(A) and (e~(2~(B) above and(fI(4~ below, for up to an additional 5000 kg of mediacontaminated with non—acute hazardous waste, 500 kg of e~ynon—acute hazardous waste, 2500 ka of media contaminatedwith acute hazardous waste, and 1 kg of acute hazardous
20
~j In response to requests for authorization to ship,store, and conduct further treatability atudyiea inadvance of commencing treatability studies. Factorsto be considered in reviewing such requests includethe nature of the technology, the type of process(e.g., batch versus continuous), the size of the unitundergoing testing I narticularly in relation to scale—u~ considerations), the time or quantity of materialrequired to reach steady—state operating conditions,or test design considerations, such as mass balancecalculations.
~j In response to requests for authorization to ship,store, and conduct treatability studies on additionalquantities after initiation or completion of initialtreatability studiesevaluation when: There has beenan equipment or mechanical failure during the conductof the treatability study; there is need to verify theresults of a previously~conducted treatability study;there is a need to study and analyze alternativetechniques within a previously~evaluated treatmentprocess; or,- there is a need to do further evaluationof an ongoing treatability study to determine finalspecifications for treatment..—
çj~. The additional quantities allowed and timefrainesallowed in subsections (eI(3’~(A1 and (eI(3)(B) aboveare subject to all the provisions in subsections(e)(1) and (e)(2)(B) through (e)(2)(F)’,- above. Thegenerator or sample collector muctshall apply to theAgency and provide in writing the followinginformation:
A~) The reason why the generator or sample collectorrequires additional time or quantity of samplefor the treatability study evaluation and theadditional time or quantity needed;
au) Documentation accounting for all samples ofhazardous waste from the wastestream w~e~thathave been sent for or undergone treatabilitystudies, including the date each previous samplefrom the waste stream was shipped, the quantityof each previous shipment, the laboratory ortesting facility to which it was shipped, whattreatability study processes were conducted oneach sample shipped, and the available resultsof each treatability study;
Gjjj) A description of the technical modifications orchange in specifications whichthat will beevaluated and the expected results;
~ii) If such further study is being required due toequipment or mechanical failure, the a.pplicantmuatshall include information regarding thereason for the failure or breakdown and alsoinclude what procedures or equipmentimprovements have been made to protect: againstfurther breakdowns; and,-
21
av) Such other information as the Agency determinesis necessary.
4) Final Agency determinations pursuant to this subsection maybe appealed to the Board.
f) Samples undergoing treatability studies at laboratories or testingfacilities. Samples undergoing treatability studies and thelaboratory or testing facility conducting such treatabilitystudies (to the extent such facilities are not otherwise subjectto RCRA requirements) are not subject to any requirement of thisPart, or of 35 Ill. Mm. Code 702, 703, 705, 722 through 726, and728, or to the notification requirements of Section 3010 of theResource Conservation and Recovery Act, provided that therequirements of subsections (f)(1) through (f)(11), below, aremet. A mobile treatment unit may qualify as a testing facilitysubject to subsections (f)(1) through (f)(11), below. Where agroup of mobile treatment units are located at the same site, thelimitations specified in subsections (f)(1) through (f)(1l),below, apply to the entire group of mobile treatment unitscollectively as if the group were one mobile treatment unit.
1) No less than 45 days before conducting treatability studies,the facility notifies the Agency in writing that it intendsto conduct treatability studies under this subsection.
2) The laboratory or testing facility conducting thetreatability study has a U.S. EPA identification number.
3) No more than a total of ~-S-10,000 kg of “as received” mediacontaminated with non—acute hazardous waste, 2500 kg ofmedia contaminated with acute hazardous waste, or 250 kg ofother “as received” hazardous waste is subjected toinitiation of treatment in all treatability studies in anysingle day. “As received” waste refers to the waste asreceived in the shipment from the generator or samplecollector.
4) The quantity of “as received” hazardous waste stored at thefacility for the purpose of evaluation in treatabilitystudies does not exceed 104,QO0 kg, the total of which caninclude 10,000 kg of media contaminated with non-acutehazardous waste. 2500 kg of agile, wator or dcbriamediacontaminated with acute hazardous waste, 1000 kg of non—acute hazardous wastes other than contaminated media, e*artd1 kg of acute hazardous waste. This quantity limitationdoes not include.-
Treatabiiity otuay r~eo~auco; rind.
B) Ttreatment materials (including nonhazardous solidwaste) added to “as received” hazardous waste.
5) No more than 90 days have elapsed since the treatabilitystudy for the sample was completed, or no more than one year(two years for treatability studies involvingbioremediation) has elapsed since the generator or samplecollector shipped the sample to the laboratory or testingfacility, whichever date first occurs. tip to 500 kg oftreated material from a particular waste stream fromtreatability studies may be archived for future evaluationup to five years from the date of initial receint.
22
Quantities of materials archived are counted against thetotal storage limit for the facility.
6) The treatability study does not involve the placement ofhazardous waste on the land or open burning of hazardouswaste.
7) The facility maintains records for 3 years followingcompletion of each study that show compliance with thetreatment rate limits and the storage time and quantitylimits. The following specific information must be, includedfor each treatability study conducted:
A) The name, address4, and U.S. EPA identification numberof the generator or sample collector of each wastesample;
B) The date the shipment was received;
C) The quantity of waste accepted;
U) The quantity of “as received” waste in storage eachday;
B) The date the treatment study was initiated and theamount of “as received” waste introduced to treatmenteach day;
F) The date the treatability study was concluded;
G) The date any unused sample or residues generated fromthe treatability study were returned to the generatoror sample collector or, if sent to a designatedfacility, the name of the facility and the U.S. EPAidentification number.
8) The facility keeps, on—site, a copy of the treatabilitystudy contract and all shipping papers associated with thetransport of treatability study samples to and from thefacility for a period ending 3 years from the completiondate of each treatability study.
9) The facility prepares and submits a report to the Agency byMarch 15 of each year that estimates the number of studiesand the amount of waste expected to be used in treatabilitystudies during the current year, and includes the followinginformation for the previous calendar year:
A) The name, address4,and U.S. EPA identification numberof the facility conducting the treatability studies;
B) The types (by process) of treatability studiesconducted;
C) The names and addresses of persons for whom studieshave been conducted (including their U.S. EPAidentification numbers);
D) The total quantity of waste in storage each day;
B) The quantity and types of waste subjected totreatability studies;
23
F) When each treatability study was conducted; and
G) The final disposition of residues and unused sample
from each treatability study.~
10) The facility determines whether any unused sample orresidues generated by the treatability study are hazardouswaste under Section 721.103 and, if so, are subject to 35Ill. Adm. Code 702, 7034, and 721 through 728, unless theresidues and unused samples are returned to the sampleoriginator under the subsection (e) exemption above.
Il) The facility notifies the Agency by letter when the facilityis no longer planning to conduct any treatability studies atthe site.
(Source: Amended at Ill. Reg. _________, effective
Section 721.133 Discarded Commercial Chemical Products, Off—SpecificationSpecies, Container Residues4, and Spill Residues Thereof
The following materials or items are hazardous wastes if and when they arediscarded or intended to be discarded as described in Section721.102(a) (2) (A), when they are mixed with waste oil or used oil or othermaterial and applied to the land for dust suppression or road treatment, whenthey are otherwise applied to the land in lieu of their original intended useor when they are contained in products that are applied to land in lieu oftheir original intended use, or when, in lieu of their original intended use,they are produced for use as (or as a component of) a fuel, distributed foruse as a fuel, or burned as a fuel.
a) Any commercial chemical product, or manufacturing chemicalintermediate having the generic name listed in subsections (e) or(f) below.
b) Any off—specification commercial chemical product or manufacturingchemical intermediate which, if it met specifications, would havethe generic name listed in subsections (e) or (f) below.
C) Any residue remaining in a container or inner liner removed from acontainer that has held any commercial chemical product ormanufacturing chemical intermediate having the generic name listedin subsection (e) or (f) below, unless the container is empty asdefined in Section 721.107(b) (3).
BOARD NOTE: Unless the residue is being beneficially used orreused, or legitimately recycled or reclaimed, or beingaccumulated, stored, transported4, or treated prior to such use,reuse, recycling4, or reclamation, the Board considers the residueto be intended for discard, and thus a hazardous waste. Anexample of a legitimate reuse of the residue would be where theresidue remains in the container and the container is used to holdthe same commercial chemical product or manufacturing chemicalintermediate it previously held. An example of the discard of theresidue would be where the drum is sent to a drum reconditionerw~ethat reconditions the drum but discards the residue.
d) Any residue or contaminated soil, water4, or other debris resultingfrom the cleanup of a spill, into or on any land or water of anycommercial chemical product or manufacturing chemical intermediatehaving the generic name listed in subsection (e) or (f)below, or
24
any residue or contaminated soil, water4, or other debris resultingfrom the cleanup of a spill, into or on any land or water, of anyoff—specification chemical product or manufacturing chemicalintermediate which, if it met specifications, would have thegeneric name listed in subsection (e) or (f) below.
BOARD NOTE: The phrase “commercial chemical product ormanufacturing chemical intermediate having the generic name listedin ...“ refers to a chemical substance whichthat is manufacturedor formulated for commercial or manufacturing use which consistsof the commercially pure grade of the chemical, any technicalgrades of the chemical that are produced or marketed, and allformulations in which the chemical is the sole active ingredient.It does not refer to a material, such as a manufacturing processwaste, that contains any of the substances listed in subsections(e) or (f) below. Where a manufacturing process waste is deemedto be a hazardous waste because it contains a substance listed insubsections (e) or (f) below, such waste will be listed in eitherSections 721.131 or 721.132 or will be identified as a hazardouswaste by the characteristics set forth in Subpart C.
e) The commercial chemical products, manufacturing chemicalintermediates4, or off—specification commercial chemical productsor manufacturing chemical intermediates referred to in subsections(a) through (d) above, are identified as acute hazardous waste (H)and are subject to the small quantity exclusion defined in Section721.105(e). These wastes and their corresponding EPA HazardousWaste Numbers are:
BOARDNOTE: For the convenience of the regulated community theprimary hazardous properties of these materials have beenindicated by the letters T (Toxicity), and R (Reactivity). A~~bsence of a letter indicates that the compound only is listed foracute toxicity.
ChemicalHazardous AbstractsWaste No. No. Substance
P023 107—20—0 Acetaldehyde, chloro—P002 591-08—2 Acetamide, N—(axninothioxomethyl)P057 640—19—7 Acetamide, 2-f luoro—P058 62—74—8 Acetic acid, fluoro—, sodium saltP002 591—08—2 1—Acetyl—2—thioureaP003 107—02—8 AcroleinP070 116—06—3 AldicarbP004 309—00—2 AldrinP005 107—18—6 Allyl alcoholP006 20859—73—8 Aluminum phosphide (R,T)P007 2763—96—4 5—(Aminomethyl )—3—iaoxazololP008 504—24—5 4—AminopyridineP009 131—74—8 Ammonium picrate (R)P119 7803-55—6 .Ammonium vanadateP099 506—61—6 Argentate(l—), bis(cyano—C)—, potassiumP010 7778—39—4 Arsenic acid HAsO4P012 1327—53-3 Arsenic oxide As203P011 1303—28—2 Arsenic oxide As2O5POll 1303—28—2 Arsenic pentoxideP012 1327-53—3 Arsenic trioxideP038 692—42—2 Arsine, diethyl—P036 696—28—6 Arsonous dichioride, phenyl—P054 151—56—4 Aziridine
25
P067 75—55—8 Aziridine, 2—methylP013 542—62—1 Barium cyanideP024 106—47-8 Benzenamine, 4—chioro—P077 100—01-6 Beazenamine, 4-nitro—P028 100-44-7 Benzene, (chioromethyl)—P042 51—43-4 1, 2—Benzenediol, 4—(1—hydroxy—2—
(methylamino)ethyl)—, (R)—P046 122-09-8 Benzeneethanamine, alpha,alpha-di—
methyl-P014 108—98-5 BenzenethiolP001 P81-81-2 2H—1—Benzopyran—2—one, 4-hydroxy-3- (3-
oxo—1—phenylbutyl)—, and salts, whenpresent at concentrations greater than0.3%
P028 100—44-7 Benzyl chlorideP015 7440—41—7 Beryllium powderP017 598—31—2 BromoacetoneP018 357—57—3 BrucineP045 39196—18-6 2—Butanone, 3, 3-dimethyl-1- (methyl—
thio) -, O-(methylaniino ) carbonyl) oximeP021 592—01—8 Calcium cyanideP021 592—01-8 Calcium cyanide Ca(CN)2P022 75—15—0 Carbon disulfideP095 75—44—5 Carbonic dichiorideP023 107—20-0 ChloroacetaldehydeP024 106—47—8 p—ChloroanilineP026 5344—82-i. l—(o—Chlorophenyl)thioureaP027 542—76—7 3—ChloropropionitrileP029 544—92-3 Copper cyanideP029 544—92—3 Copper cyanide CuCNP030 Cyanides (soluble cyanide salts), not
otherwise specifiedP031 460-19-5 CyanogenP033 506-77—4 Cyanogen chlorideP033 506-77-4 Cyanogen chloride CNC1P034 131-89—5 2—Cyclohexyl—4, 6—dinitrophenolP016 542-88—1 Dichioromethyl etherP036 696—28—6 DichlorophenylarsineP037 60—57—1 DieldrinP038 692—42—2 DiethylarsineP041 311—45-S Diethyl—p-nitrophenyl phosphateP040 297—97—2 0,0—Diethyl 0—pyrazinyl
phosphorothioateP043 55—91-4 Diisopropylfluorophosphate (DFP)P004 3 09-00—2 1,4,5, 8-Dimethanonaphthalene,
1,2,3,4,10, 10—hexachloro—1,4,4a,5,8,Ba—hexahydro—,(lalpha, 4alpha, 4abeta, Salpha,8alpha, 8abeta) —
P060 4 65—73-6 1, 4,5, 8—Di—methanonaphthalene,1,2, 3,4, 10, 10—hexachloro—1, 4, 4a, 5, 8, 8a—hexahydro—,(lalpha, 4alpha, 4abeta,Sbeta,8beta, 8abeta)—
P037 60—57—1 2,7:3, ,3—b)oxirene,3, 4, 5, 6,9 , 9—hexachloro—la, 2, 2a,3, 6, 6a, 7, 7a—octahydro—,(laalpha, 2beta, 2aalpha, 3beta,6beta, 6aalpha, 7beta, 7aalpha)—
26
P051 P72—20—8 2,7:3,6-Dimethanonaphth(2,3—b]oxirene,3,4,5, 6,9,9—hexachloro—la, 2, 2a, 3,6, 6a, 7, 7a—octahydro—,(laalpha, 2beta,2abeta,3alpha,6alpha, 6abeta, 7beta, 7aalpha) —, andmetabolites
P044 60—51—5 DimethoateP046 122-09-8 alpha, alpha—DimethylphenethylamineP047 534—52—1 4,6-Dinitro—o—creaol and saltsP048 51—28—5 2,4—DinitrophenolP020 88—85—7 DinosebP085 152—16—9 Diphosphoramide, octamethyl—P111 107—49—3 Diphosphoric acid, tetraethyl esterP039 298—04—4 DisulfotonP049 541-53—7 DithiobiuretP050 115—29—7 EndosulfanP088 145—73—3 EndothallP051 72—20—8 EndrinP051 72—20-8 Endrin, and metabolitesP042 51—43-4 EpinephrineP031 460—19—5 EthanedinitrileP066 16752—77—5 Ethanimidothioic acid, N—[((methyl—
amino)carbonyl)oxy]—, methyl esterP101 107-12—0 Ethyl cyanideP054 151—56—4 EthylenimineP097 52—85—7 FamphurP056 7782—41—4 FluorineP057 640-19-7 FluoroacetamideP058 62—74—8 Fluoroacetic acid, sodium saltP065 628—86—4 Fulminic acid, mercury (2+) salt (R,T)P059 76—44—8 Heptachlor.P062 757-58—4 Hexaethyl tetraphosphateP116 79—19—6 HydrazinecarbothioamideP068 60—34—4 Hydrazine, methyl-P063 74—90—8 Hydrocyanic acidP063 74-90—8 Hydrogen cyanideP096 7803—51—2 Hydrogen phosphideP060 465—73—6 IsodrinP007 2763—96—4 3(2H)—Isoxazolone, 5—(aminomethyl)—P092 62—38—4 Mercury, (acetato-O)phenyl—P065 628—86—4 Mercury fulminate (R,T)P082 62—75—9 Methanamine, N—methyl—N—nitroso-P064 624—83—9 Methane, isocyanato—P016 542—88—1 Methane, oxybis(chloro-P112 509—14—B Methane, tetranitro— (R)P118 75—70—7 Methanethiol, trichloro—P050 115—29-7 6, 9-Methano—2, 4, 3-benzodioxathiepen,
6,7,8,9,10,10—hexachloro—1,S,5a,6,9,9a—hex ahydro—, 3-oxide
P059 76—44—8 4,7—Methano—1H—indene, 1,4,5,6,7,8,8—heptachloro—3a, 4,7, 7a-tetrahydro—
P066 16752—77—5 MethomylP068 60—34—4 Methyl hydrazineP064 624—83—9 Methyl isocyanateP069 75—86—5 2—MethyllactonitrileP073. 298—00—0 Methyl parathionP072 86—88—4 alpha—NaphthylthioureaP073 13463—39—3 Nickel carbony].P073 13463—39—3 Nickel carbonyl Ni(C0)4, (T—4)—P074 557—19—7 Nickel cyanideP074 557—19—7 Nickel cyanide Ni(CN)2P075 54—11—5 Nicotine, and salts
27
P076 10102—43—9 Nitric oxideP077 100-01—6 p-NitroanilineP078 10102—44—0 Nitrogen dioxideP076 10102—43—9 Nitrogen oxide NOP078 10102—44—0 Nitrogen oxide NO2P081 55—63—0 Nitroglycerine (R)P082 62—75—9 N—NitrosodimethylamineP084 4549-40-0 N-Nitrosomethy].vinylamineP085 152-16—9 Octaxnethy].pyrophosphoramideP087 20816—12—0 Osmium oxide 0804f (T—4)—P087 20816—12—0 Osmium tetroxideP088 145—73—3 7—Oxabicyclo(2.2. 1]heptane—2,3—di—
carboxylic acidP089 56—38—2 ParathionP034 131—89—5 Phenol, 2—cyclohexyl—4,6—dinitro—P048 51—28—5 Phenol, 2,4—dinitro—P047 P534-52—i Phenol, 2—methyl—4,6—dinitro—, and
saltsP020 88—85—7 Phenol, 2—(1—methylpropyl)--4, 6—dinitro—P009 131—74—8 Phenol, 2,4,6—trinitro—, axnmonium salt
(R)P092 62—38—4 Phenylmercury acetateP093 103—85—5 PhenyithioureaP094 298—02—2 PhorateP095 75-44-5 PhosgeneP096 7803—51—2 PhosphineP04]. 311—45—5 Phosphoric acid, diethyl 4—nitrophenyl
esterP039 298—04-4 Phosphorodithioic acid, 0,0—diethyl S—
[2— (ethylthio ) ethyl] esterP094 298—02-2 Phosphorodithioic acid, 0,0—diethyl S-
((ethylthio)methyl) esterP044 60-51—5 Phosphorodithioic acid, 0,0—dimethyl S—
[2— (methylamino )—2—oxoethyl ]esterP043 55—91—4 Phosphorofluoridic acid, bis(1—methyl—
ethyl) esterP089 56—38—2 Phosphorothioic acid, O,0-diethyl O-(4—
nitrophenyl) esterP040 297—97—2 Phosphorothioic acid, 0,0-diethyl 0—
pyrazinyl esterP097 52-85—7 Phosphorothioic acid, O—[4-[(dimethyl-
amino)sulfonyl)]phenylj 0,0—dirnethylester
P071 298—00—0 Phosphorothioic acid, O,O—dimethyl 0—(4-nitrophenyl) ester
P110 78-00—2 Plumbane, tetraethyl—P098 151—50—8 Potassium cyanideP098 151—50—8 Potassium cyanide KCNP099 506—61—6 Potassium silver cyanideP070 116—06-3 Propanal, 2—methyl—2—(methylthio)—, 0—
((methylamino)carbonyl)oximeP101 107—12—0 PropanenitrileP027 542—76-7 Propanenitrile, 3—chloro-P069 75-86-5 Propanenitrile, 2—hydroxy-2-methyl—P081 55—63—0 1,2,3—Propanetriol, trinitrate— (A)P017 598—31—2 2—Propanone, l-bromo—P102 107—19—7 Propargyl alcoholP003 107-02—8 2—PropenalP005 107—18—6 2—Propen—1—olP067 75—55—8 1,2—PropylenimineP102 107—19—7 2—Propyn—1—o1P008 504—24—5 4—Pyridinamine
28
P075 P54—11—5 Pyridine, 3—(1—rnethyl—2—pyrrolidinyl)—,(S)— and salts
P114 12039—52—0 Selenious acid, dithallium (1+) saltP103 630-10—4 SelenoureaP104 506—64—9 Silver cyanideP104 506—64—9 Silver cyanide AgCNP105 26628—22—8 Sodium azideP106 143—33—9 Sodium cyanideP106 143-33—9 Sodium cyanide NaCMP108 P57-24—9 Strychnidin-lO—one, and saltsP018 357-57—3 Strychnidin—lO—one, 2,3—dimethoxy—P108 P57-24—9 Strychnine and saltsP115 7446—18—6 Sulfuric acid, dithalliuxn (1+) saltP109 3689—24-5 TetraethyldithiopyrophosphateP110 78—00—2 Tetraethyl leadP111 107-49—3 TetraethylpyrophosphateP112 509—14—8 Tetranitromethane (A)P062 757—58—4 Tetraphosphoric acid, hexaethyl esterP113 1314—32—5 Thallic oxideP113 1314—32—5 Thallium oxide Tl20,P114 12039—52—0 Thallium (I) seleniteP115 7446—18—6 Thallium (I) sulfateP109 3689—24—5 Thiodiphosphoric acid, tetraethyl esterP045 3919 6—18—4 ThiofanoxP049 541—53—7 Thioimidodicarbonic diamide
[(H2N)C(S)]2NHP014 108—98—5 ThiophenolP116 79—19—6 ThiosemicarbazideP026 5344-82—1 Thiourea, (2-chlorophenyl)-P072 86-88—4 Thiourea, 1—naphthalenyl-P093 103—85—5 Thiourea, phenyl—P123 8001-35—2 ToxapheneP118 75-70-7 TrichloromethanethiolP119 7803—55—6 Vanadie acid, ammonium saltP120 1314—62—1 Vanadium oxide V205P120 1314—62—1 Vanadium pentoxideP084 4549-40—0 Vinylamine, N—methyl-M—nitroso—P001 P81—81-2 Warfarin, and salts, when present at
concentrations greater than 0.3%.P121 557—21—1 Zinc cyanideP121 557—21—1 Zinc cyanide Zn(CN)2P122 1314—84—7 Zinc phosphide Zn3?,, when present at
concentrations greater than 10% (R,T)
f) The commercial chemical products, manufacturing chemicalintermediates4, or off—specification commercial chemical productsreferred to in subsections (a) through (d) above, are identifiedas toxic wastes (T) unless otherwise designated and are subject tothe small quantity exclusion defined in Section 721.105(a) and(g). These wastes and their corresponding EPA Hazardous WasteNumbers are:
BOARD NOTE: For the convenience of the regulated community, theprimary hazardous properties of these materials have beenindicated by the letters T (Toxicity), R (Reactivity), I(Ignitability)4, and C (Corrosivity). AThe_absence of a letterindicates that the compound is only listed for toxicity.
29
ChemicalHazardous AbstractsWaste No. No. Substance
U001 75—07—0 Acetaldehyde (I)U034 75—87—6 Acetaldehyde, trichloro—U187 62—44-2 Acetamide, N—(4—ethoxyphenyl)-U005 53—96—3 Acetamide, N—9H—fluoren—2—yl—U240 P 94—75—7 Acetic acid, (2,4—dichlorophenoxy)—,
salts and estersU112 141—78—6 Acetic acid, ethyl ester (I)U144 301—04—2 Acetic acid, lead (2+) saltU214 563—68—8 Acetic acid, thallium (1+) saltSee F027 93—76—5 Acetic acid, (2,4,5—trichlorophenoxy)—U002 67—64—1 Acetone (I)tJOO3 75—05—8 Acetonitrile (I,T)U004 98-86-2 AcetophenoneU005 53—96—3 2—AcetylaminofluoreneU006 75—36—5 Acetyl chloride (C,R,T)U007 79—06—1 AcrylamideU008 79—10—7 Acrylic acid (I)U009 107—13—1 AcrylonitrileU011 61—82—5 AmitroleU012 62—53—3 Aniline (I,T)U136 75—60—S Arsinic acid, dimethyl—U014 492-80—8 AuraxnineU015 115—02—6 AzaserineU010 50—07—7 Azirino(2’,3’:3,4]pyrrolo(1,2—a]indole—
4,7—dione, 6—amino—8—[ (aminocarbonyl)—oxy]methyl ]—1, la, 2,8, 8a, 8b—hexahydro—8a—methoxy-5—methyl—, [1a—S—(laalpha, Sbeta, Saalpha, 8balpha) 1—
Ul57 56—49—5 Benz[j ]aceanthrylene, 1, 2—dihydro—3—methyl—
U016 225—51—4 Benz(c)acridine13017 98—87—3 Benzal chlorideUl92 23950—58—5 Benzainide, 3,5—dichloro—N—(l,1—di—
methyl-2-propynyl) —
13018 56—55—3 Benz[a]anthracene13094 57—97—6 Benz(a)anthracene, 7, l2—dimethyl—U012 62—53—3 Benzenamine (I,T)13014 492—80—8 Benzenamine, 4,4’ -carbonimidoylbis[N,N—
dimethyl—13049 3165-93—3 Benzenamine, 4—chloro—2-methyl—,
hydrochlorideU093 60—11—7 Benzenamine, N,N-dimethyl-4—(phenyl—
azo)—t1328 95—53—4 Benzenaxnine, 2—methyl—U353 106—49-0 Benzenaznine, 4-methyl—13158 101—14-4 Benzenamine, 4,4’—methylenebis[2-
chloro—13222 636—21—5 Benzenainine, 2-methyl-, hydrochlorideU181 99-55—8 Senzenamine, 2—methyl—5—nitro—U019 71-43—2 Benzene (I,T)U038 510—15—6 Benzeneacetic acid, 4—chloro—alpha—(4—
chlorophenyl) -alpha—hydroxy-, ethylester
13030 101-55-3 Benzene, 1—bromo-4—phenoxy—17035 305—03-3 Benzenebutanoic acid, 4—(bis(2—chloro—
ethyl) amino]—17037 108—90-7 Benzene, chloro—17221 25376—45—8 Benzenediamine, ar—methyl—
30
0028 117—81—7 1,2—Benzanedicarboxylic acid, bis(2—ethylhexyl) ester
13069 84—74—2 l,2—Benzenedicarboxylic acid, dibutylester
17088 84—66—2 1,2-’Benzenedicarboxylic acid, diethylester
U102 131—11—3 1,2—Benzenedicarboxylic acid, dimethylester
U107 117—84—0 1,2—Benzenedicarboxylic acid, dioctylester
U070 95—50—1 Benzene, 1,2—dichloro—U071 541—73—1 Benzene, 1,3—dichloro—13072 106—46—7 Benzene, 1,4—dichioro—13060 72—54-8 Benzene, 1, 1’—(2,2—dichloroethylidene)—
bis[ 4—chioro—U017 98—87—3 Benzene, (dichioromethyl)—0223 26471—62—5 Benzene, l,3—diisocyanatornethyl— (R,T)U239 1330—20—7 Benzene, dimethyl— (I,T)17201 108—46—3 1,3—Benzenediol13127 118—74—1 Benzene, hexachloro—17056 110-82—7 Benzene, hexahydro— (I)13220 108—88—3 Benzene, methyl-13105 121—14—2 Benzene, 1—methyl—2,4—dinitro—13106 606-20—2 Benzene, 2-methyl—1,3-dinitro—13055 98—82—8 Benzene, (1—methylethyl)— (I)17169 98—95—3 Benzene, nitro—13183 608-93—5 Benzene, pentachloro—U185 82-68-8 Benzene, pentachioronitro—0020 98—09—9 Benzenesulfonic acid chloride (C,R)0020 98—09—9 Benzenesulfonyl chloride (C,R)17207 95—94—3 Benzene, 1,2,4,5—tetrachloro—U06]. 50—29—3 Benzene, 1,1’—(2,2,2—trichloroethyl—
idene) bis [4—chloro—13247 72—43—5 Benzene, 1,1’—(2,2,2—trichloroethyl—
idene) bis [4—methoxy-U023 98-07—7 Benzene, (trichloromethyl)—17234 99—35—4 Benzene, 1,3,5—trinitro—13021 92—87—5 Benzidene13202 P 81-07—2 1,2—Benzisothiazol—3(2H)—one, 1,1—di-
oxide, and salts13203 94—59—7 1,3—Benzodioxole, S—(2—propenyl)-13141 120—58—1 1, 3—Benzodioxole, 5—(l—propenyl)—17090 94—58—6 1,3—Benzodioxole, 5—propyl—U064 189—55—9 Benzo[rst)pentaphene0248 P 81—81—2 2H—1—Benzopyran-2—one, 4—hydroxy—3—(3—
oxo—1-phenylbutyl)—, and salts, whenpresent at concentrations of 0.3% orless
U022 50—32—8 ~enzo(a3pyreneU197 106—51—4 p—Benzoquinone0023 98—07—7 Benzotrichloride (C,R,T)13085 1464-53—5 2,2’—Bioxirane13021 92—87—5 (1,1 ‘—Biphenyl]—4,4 ‘—diamineU073 91—94—1 •(1,1’—Biphenyl]—4,4’—diamine, 3,3’—di—
chloro—U09l 119—90—4 (1,1’—Biphenyl)—4,4’—diamine, 3,3’—di—
methoxy—13095 119—93—7 [1,1’—Biphenyl]—4,4’—diamine, 3,3’—di—
methyl—U225 75-25—2 BromoformU030 101-55—3 4—Bromophenyl phenyl etherU128 87—68—3 1,3—Butadiene, 1,l,2,3,4,4—hexachloro—
31
17172 924—16—3 1—Butanamine, N-butyl—N—nitroso—U031 71—36—3 l—Butanol (I)U159 78—93—3 2—Butanone (I,T)11160 1338—23-4 2—Butanone, peroxide (R,T)U053 4170—30—3 2—ButenalU074 764-41—0 2—Butene, 1,4-dichloro— (I,T)0143 303—34—4 2—Butenoic acid, 2—methyl—, 7—[(2,3—di—
hydroxy-2— ( 1-methoxyethyl) -3-methyl-i-oxobutoxy ]methyl) —2,3,5, 7a—tetrahydro-1H—pyrrolizin—1—yl ester, [iS—(lalpha(Z), 7(2S*,3R*), 7aalphaj)—
13031 71—36—3 n—Butyl alcohol (I)13136 75—60—S Cacodylic acid13032 13765—19—0 Calcium chromateU238 51-79—6 Carbamic acid, ethyl ester17178 615—53—2 Carbamic acid, methylnitroso—, ethyl
ester0097 79—44—7 Carbamic chloride, dimethyl—13114 P 111—54—6 Carbamodithioic acid, 1,2—ethanediyl-
bis—, salts and esters0062 2303—16-4 Carbamothioic acid, bis(1—methyl—
ethyl)-, 5— (2 , 3-dichloro—2-propenyl)ester
17215 6533—73—9 Carbonic acid, dithallium (1+) salt17033 353—50—4 Carbonic difluoride13156 79-22—1 Carbonochioridic acid, methyl ester
(I,T)0033 353—50-4 Carbon oxyfluoride (R,T)0211 56—23—5 Carbon tetrachloride13034 75—87—6 ChloralU035 305—03—3 Chlorambucil0036 57-74—9 Chlordaneaipha and gamma isomers17026 494—03—1 ChiornaphazinU037 108—90—7 Chlorobenzene0038 510—15—6 Chlorobenzilate13039 59-50—7 p—Chloro-m—cresol0042 110—75—8 2—Chloroethyl vinyl ether0044 67—66—3 Chloroform13046 107—30-2 Chloromethyl methyl ether13047 91—58—7 beta—Chloronaphthalene0048 95—57—8 o—Chlorophenol13049 3165—93—3 4—Chloro—o-toluidine, hydrochloride13032 13765—19—0 Chromic acid H2CrO4, calcium saltU050 218—01—9 Chrysene13052. CreosoteU052 1319—77—3 Cresol (Cresylic acid)13053 417 0—30-3 CrotonaldehydeU055 98—82—8 Cumeme (I)0246 506—68—3 Cyanogen bromide CNBrU197 106—51—4 2, 5—Cyclohexadiene-l, 4—dione0056 110—82—7 Cyclohexane (I)13129 58—89—9 Cyclohexane, 1,2,3,4,5,6—hexachioro—,
(lalpha, 2alpha, 3beta, 4alpha,Salpha, 6beta) -
0057 108—94—1 Cyclohexanone (I)17130 77—47—4 1,3—Cyclopentadiene, 1,2, 3,4,5,5—hexa—
chloro—13058 50—18-0 Cyclophosphamide11240 P 94—75—7 2,4—D, salts and esters0059 20830—81—3 Daunornycin17060 72—54--8 DDD13061 50—29—3 DDT
32
Dial lateDibenz[a, h) anthraceneDibenzo[a, i)pyrene1, 2—Dibromo—3—chloropropaneDibutyl phthalateo—Dichlorobenzenem—Dichlorobenzenep—Dichlorobenzene3,3 ‘—Dichlorobenzidine1, 4—Dichloro-2—butene (I, T)Dichlorodif luoromethane1, 1—Dichloroethylene1, 2—DichioroethyleneDichloroethyl etherDichloroisopropyl etherDichloromethoxy ethane2, 4-Dichiorophenol2, 6-Dichlorophenol1, 3-.Dichloropropene1,2:3,4—Diepoxybutane (I,T)1,4-Diet hyleneoxideDiethylhexyl phthalateN, N’ —Diethylhydrazine0, 0-Diethyl S-methyl dithiophoaphateDiethy]. phthalateDiethylstilbeetroi.Dihydrosafrole3,3’ -DimethoxybenzidineDimethylamine (I)p—Ditnethylaminoazobenzene7, 12—Dimethylbenz (a] anthracene3,3’ —Dimethylbenzidinealpha, alpha—Dimethyl—benzylhydroperoxide (A)Diniethylcarbamoyl chloride1, 1—Dimethylhydrazine1, 2-Dimethyihydrazine2, 4—DimethyiphenolDimethyl phthalateDirnethyl sulfate2, 4-Dinitrotoluene2, 6-DinitrotolueneDi—n—octyl phthalate1, 4—Dioxane1 ,2-DiphenylhydrazineDipropylamine (I)Di—n-propylnitrosaxnineEpichlorohydrinEthanal (I)Ethanamine, N-ethyl-N-nitroso-1,2—Ethanediamine, N,N—dimethyl-M’ —2-pyridinyl—N’ — (2—thienylmethyl) —
Ethane, 1, 2—dibromo—Ethane, 1, 1—dichloro-Ethane, 1,2—dichloro—Ethane, hexachloro—Ethane, 1,l’—(methylenebis(oxir) ]bis(2—ch loro—Ethane, 1,1’—oxybis— (I)Ethane, 1,1’ -oxybis(2—chloro—Ethane, pentachloro—Ethane, 1,1, 1, 2—tetrachloro—
U062110631106413066110690070130710072U073007411075U078007900251302711024130810082(1084U0851710813028U08613087130881308917090130911309200931309400950096
U09700981709915101131021310301051110613107151080109Ui 10111111704117001U174
2303—16—453—70—3189—55—996—12—884—74—295—50—1541—73—1106—46—791—94—1764—41—075—71—875—35—4156—60—5111—44—4108—60—1111—91—1120—83—287—65—0542—75—61464—53—5123—91—1117—81—71615—80-13288—58—284—66-256—53—194—58—6119—90—4124—40—360—11—757—97—6119—93—780—15—9
79—44—757—14—7540—73—8105—67—9131—11—377—78—1121—14—2606—20—2117—84—0123—91—1122—66—7142—84—7621—64—7106—89—875—07—05 5—18—5
17155 91—80—5
00671307615077U13 111024
13117002501840208
106—93—475—34—3107—06—267—72—i111—91—1
60—29—7111—44—476—01—7630—20—6
33
11209 79—34—5 Ethane, 1,l,2,2—tetrachloro—U218 62—55—S EthanethioamideU226 71—55—6 Ethane, l,l,1—trichloro—U227 79—00—S Ethane, 1,1,2—trichloro—13359 110—80—5 Ethanol, 2—ethoxy-U173 1116—54—7 Ethanol, 2,2 ‘—(nitrosoimino)bis—11004 98-86—2 Ethanone, l—phenyl—U043 75—01—4 Ethene, chloro—U042 110—75-8 Ethene, (2-chloroethoxy)—17078 75—35—4 Ethene, 1,1—dichloro—13079 156—60—5 Ethene, 1,2—dichloro—, (B)—U210 127—18—4 Ethene, tetrachloro—11228 79-01—6 Ethene, trichloro-(1112 141—78—6 Ethyl acetate (I)0113 140—88—5 Ethyl acrylate (I)U238 51—79-6 Ethyl carbamate (urethane)U117 60—29—7 Ethyl etherU114 P 111—54—6 Ethylenebiadithiocarbamic acid, salts
and esters13067 106—93—4 Ethylene dibromide13077 107-06—2 Ethylene dichlorideU359 110—80—S Ethylene glycol monoethyl ether13115 75-21—8 Ethylene oxide (I,T)U1l6 96—45—7 Ethylenethiourea11076 75-34—3 Ethylidene dichloride13118 97—63—2 Ethyl methacrylateUl19 62-50-0 Ethyl methanesulfonate17120 206—44—0 Fluoranthene13122 50—00-0 Formaldehyde(1123 64—18—6 Formic acid (C,T)0124 110—00—9 Furan (I)U125 98—01—i 2—Furancarboxaldehyde (I)13147 108—31—6 2,5—Furandione13213 109—99—9 Furan, tetrahydro— (I)11125 98—01—1 Furfural (I)U124 110—00—9 Furfuran (I)15206 18883—66-4 Glucopyranose, 2—deoxy—2—(3—methyl—3—
nitrosoureido ) —,
U206 18883—66—4 D-Glucose, 2—deoxy—2--( [ (methylnitroso—amino) -carbonyl] amino] —
U126 765—34—4 Glycidylaldehyde15163 70—25—7 Guanidine, N-methyl-N’ —nitro-N—nitroso-U127 118-74—1 Hexachlorobenzene17128 87—68—3 Hexachiorobutadiene13130 77—47—4 Hexachlorocyclopentacliene0131 67—72—1 HexachloroethaneU132 7 0-30—4 Hexachlorophene0243 1888—71—7 Hexachioropropene15133 302—01—2 Hydrazine (R,T)13086 1615—80—1 Hydrazine, 1,2—diethyl—11098 57—14—7 Hydrazine, 1,1—dimethyl—0099 540—73—8 Hydrazine, 1,2-dimethyl—11109 122—66—7 Hydrazine, 1,~2—dipheny1—15134 7664—39—3 Hydrofluoric acid (C,T)15134 7664—39—3 Hydrogen fluoride (C,T)13135 7783—06—4 Hydrogen sulfideU135 7783—06—4 Hydrogen sulfide H2SU096 80—15-9 Hydroperoxide, 1—methyl—i -phenylethyl-
(A)0116 96—45—7 2—Imidazolidinethione0137 193—39—5 Indeno[1, 2, 3—cd]pyreneU190 85—44—9 1, 3—Isobenzofurandione
34
0140 78—83—1 Isobutyl alcohol (I,T)15141 120—58—1 Isosafrole0142 143—50—0 Xepone15143 303—34—4 Lasiocarpene0144 301—04—2 Lead acetate13146 1335—32—6 Lead, bis(acetato—O)tetrahydroxytri—15145 7446—27—7 Lead phosphate(1146 133 5—32—6 Lead subacetate0129 58—89—9 Lindane0163 70—25—7 MNNGU147 108—31—6 Maleic anhydride11148 123—33—1 Maleic hydrazide0149 109—77—3 Malononitrile15150 148—82—3 Melphalan0151 7439—97-6 Mercury0152 126—98—7 Methacrylonitrile (I ,T)U092 124—40—3 Methanamirie, N—methyl— (I)U029 74—83-9 Methane, bromo—U045 74—87—3 Methane, chloro— (I,T)U046 107—30-2 Methane, chloromethoxy—0068 74-95—3 Methane, dibromo—13080 75-09—2 Methane, dichloro—0075 75—71—8 Methane, dichlorodifluoro—17138 74-88—4 Methane, iodo—U119 62-50—0 Methanesulfonic acid, ethyl ester0211 56-23—5 Methane, tetrachloro—U153 74—93—1 Methanethiol (I,T)U225 75—25—2 Methane, tribromo—13044 67-66—3 Methane, trichloro—U12l 75-69—4 Methane, trichiorofluoro—(1036 57—74—9 4,7—Methano—1R—indene, 1,2,4,5,6,7,8,8—
octachloro—2, 3, 3a, 4,7, 7a—hexahydro—U154 67—56—1 Methanol (I)13155 91—80-5 MethapyrileneU142 143—50—0 1,3, 4—Metheno—2H—cyclobuta(cd]pentalen—
2—one, 1, la, 3,3a,4, 5,5,Sa, 5b,6—decachlorooct ahydro—
13247 72-43-5 MethoxychlorU154 67—56—1 Methyl alcohol (I)13029 74—83—9 Methyl bromideU186 504—60—9 1—Methylbutadiene (I)13045 74—87—3 Methyl chloride (I,T)Ul56 79—22—1 Methyl chiorocarbonate (I,T)~J226 71—55—6 Methylchloroform0157 56—49—5 3-Methylcholanthrene13158 101—14—4 4,4’ —Methylenebie(2—chloroaniline)U068 74—95—3 Methylene bromide13080 75—09—2 Methylene chloride13159 78—93-3 Methyl ethyl ketone (HEX) (I,T)U160 1338—23-4 Methyl ethyl ketone peroxide (R,T)17138 74—88-4 Methyl iodideUl61 108—10—i Methyl isobutyl ketone (I)13162 80—62-6 Methyl methacrylate (I,T)11161 108—10—i 4—Methyl—2—pentartone (I)U164 56—04—2 MethylthiouracilUOlO 50—07-7 Mitomycin C0059 20830-81—3 5,12—Naphthacenedione, 8—acetyl—10—((3—
amino—2 , 3, 6—trideoxy) -alpha-L-lyxo—hexapyranosyl )oxyl 3—7,8,9, 10-tetra—hydro-6, 8, 11—trihydroxy—1-methoxy-,(BS—cis)—
13167 134—32—7 1—Naphthalenamine
35
13168 91—59—8 2—Naphthalenamine0026 494—03—1 Naphthaleneamine, N,N’—bis(2—chloro—
ethyl)—11165 9 1—20—3 Naphthalene13047 91—58—7 Naphthalene, 2—chloro—11166 130—15—4 1, 4-Naphthalenedione17236 72—57—i 2,7—Naphthalenediaulfonic acid, 3,3’—
[(3,3’—dimethyl—(1,1’—biphenyl]—4,4’—diyl)bis(azo)bis[5—antino—4-hydroxy)—,tetrasodium salt
13166 130—15—4 1,4—Naphthoquinone13167 134—32—7 alpha—Naphthylainine13168 91—59-8 beta-Naphthylamine15217 10102—45—1 Nitric acid, thallium (1+) salt(1169 98—95—3 Nitrobenzene (I,T)U170 100—02—7 p—Nitrophenol15171 79—46—9 2—Nitropropane (I,T)13172 924—16—3 N—Nitrosodi—n—butylamine11173 1116—54—7 N—Nitrosodiethanolamine0174 55—18—5 N—NitrosodiethylamineU176 759-73-9 N—Nitroso—N-ethylureaU17 7 684-93—5 N—Nitroso—N-methylurea13178 615—53—2 N—Nitroso—N—methylurethsne15179 100-75—4 N—Nitrosopiperidine13180 930-55—2 N—Nitrosopyrrol. idine0181 99—55-8 S—Nitro—o-toluidineU193 1120—71-4 1,2—Oxathiolane, 2,2—dioxideU058 50-18-0 2H—1, 3, 2—Oxazaphosphorin—2-arnine, N,N-
bis(2-chloroethyl)tetrahydro-, 2-oxide11115 75—21—8 Oxirane (I,T)0126 765—34—4 Oxiranecarboxyaldehyde0041 106-89—8 Oxirane, (chloromethyl)—0182 123—63—7 ParaldehydeU183 608—93—5 Pentachlorobenzene11184 7 6—01—7 Pentachloroethar~e0185 82—68—8 Pentachloronitrobenzene (PCNB)See F027 87—86—5 Pentachlorophenol13161 108—10—1 Pentanol, 4—methyl—13186 504—60—9 1,3—Pentadiene (I)0187 62-44—2 PhenacetinU188 108—95—2 PhenolU048 95—57-8 Phenol, 2—chloro—U039 59—50—7 Phenol, 4—chloro—3—methyl—13081 120—83—2 Phenol, 2,4—dichioro—15082 87—65—0 Phenol, 2,6—dichloro—11089 56-53—1 Phenol, 4,4’—(1,2-diethyl—l,2—ethenedi-
yl)bis—, (E)—13101 105—67—9 Phenol, 2,4—dimethyl—13052 1319—77—3 Phenol, methyl—11132 70—30—4 Phenol, 2,2’ —methylenebis[3, 4, 6—tn—
chioro—15170 100—02—7 Phenol, 4—nitro—See F027 87-86—5 Phenol, pentachloro-See F027 58—90—2 Phenol, 2,3,4,6—tetrachloro-~See F027 95—95—4 Phenol, 2,4,5—tnichloro-See F027 88—06—2 Phenol, 2,4,6—trichloro—U150 148-82—3 L—Phenylalanine, 4—[bis(2-chloroethyl)-
amino]-(1145 7446—27—7 Phosphoric acid, lead (2+) salt (2:3)0087 3288—58—2 Phosphorodithioic acid, O,0—diethyl S—
methyl ester0189 1314—80—3 Phosphorus sulfide (A)
36
U190 85—44-9 Phthalic anhydride0191 109—06—8 2—Picoline0179 100—75—4 Piperidine, l—nitroso—U192 23950—58—5 Pronamide17194 107—10—8 1—Propanamine (I,T)13111 621-64-7 1-Propanamine, N—nitroso-N-propyl-U110 142—84—7 1—Propanamine, N—propyl— (I)11066 96-12-8 Propane, 1,2-dibromo—3-chloro—U083 78—87—S Propane, 1,2—dichloro-U149 109—77—3 Propanedinitrile15171 79-46—9 Propane, 2—nitro— (I,T)13027 108—60-1 Propane, 2,2 ‘—oxybis[2-chloro—See P027 93—72—1 Propanoic acid, 2—(2,4,5—trichloro—
phenoxy) -
17193 1120—71—4 1,3—Propane sultoneU235 126-72-7 1-Propanol, 2,3—dibromo—, phosphate
(3:1)U140 78—83—1 1-Propanol, 2—methyl— (I,T)U002 67—64—1 2—Propanone (I)13007 79-06—1 2—ProperiamideU084 542—75—6 1—Propene, 1,.3—dichloro—17243 1888—71—7 1—Propene, 1,1,2, 3,3,3—hexachloro—U009 107—13—i 2—PropenenitrileU152 126—98—7 2-Propenenitrile, 2—methyl— (1,1’)U008 79—10—7 2—Propenoic acid (I)Uli3 140—88—5 2—Propenoic acid, ethyl ester (I)13118 97—63—2 2—Propenoic acid, 2—methyl—, ethyl
ester0162 80—62—6 2—Propenoic acid, 2—methyl—, methyl
ester (I,T)See P027 93—72—i Propionic acid, 2—(2,4,5—trichloro—
phenoxy)—0194 107—10—8 n—Propylamine (I,T)0083 78-87—5 Propylene dichioride11148 123—33—1 3, 6—Pyridazinedione, 1, 2—dihydro—U196 110—86—1 Pyridine13191 109—06—8 Pyridine, 2—methyl—U237 66—75—1 2,4—(1H,3H)—Pyrimidinedione, 5—(bis(2—
chloroethyl )amino] -
0164 58—04—2 4(1H)-Pyrimidinone, 2, 3-dihydro-6-methyl -2 —thioxo—
0180 930—55—2 Pyrrolidine, 1—nitroso—13200 50—55—5 Reserpine13201 108-46—3 Resorcinol(1202 P 81—07—2 Saccharin and salts13203 94—59—7 Safrole0204 7783—00—8 Selenious acid11204 7783—00—8 Selenium dioxideU205 7488—56—4 Selenium sulfide13205 7488—56—4 Selenium sulfide SeS2 (R,T)13015 115—02—6 L—Serine, diazoacetate (ester)See F027 93—72—1 Silvex (2,4,5—TP)U206 18883—66—4 StreptozotocinU103 77—78—1 Sulfuric acid, dimethyl esterU189 1314—80—3 Sulfur phosphide (A)See P027 93—76—5 2,4,5—T0207 9 5—94—3 1,2,4, 5—Tetrachlorobenzene13208 630—20—6 1,1,1, 2—Tetrachioroethane0209 79—34—5 1,1,2, 2—Tetrachloroethane13210 127—18—4 TetrachloroethyleneSee F027 58—90—2 2,3,4, 6—Tetrachlorophenol0213 109—99—9 Tetrahydrofuran (I)
37
13214 563—68—8 Thallium (I) acetate13215 6533—73-9 Thallium (I) carbonate13216 7791—12—0 Thallium (I) chlorideU216 7791—12—0 Thallium chloride TIC1U2i7 10102—45—1 Thallium (I) nitrateU218 62—55-S Thioacetamide13153 74—93-1 Thiomethanol (I,T)U244 137-26-8 Thioperoxydicarbonic diamide
[(H2N)C(S) )2S2, tetramethyl—U219 62—56-6 Thiourea11244 137—26—8 Thiram11220 108—88—3 Toluene0221 25376—45-8 ToluenediamineU223 26471—62—5 Toluene diisocyanate (R,T)0328 95—53-4 o—Toluidine13353 106—49—0 p—ToluidineU222 636—21-S o-Toluidine hydrochlorideu011 61—82—S 1H—1, 2, 4—Triazol—3—amine0227 79—00—5 1, 1,2-TrichloroethaneU228 79—01-6 Trichioroethylene0121 75—69—4 TrichloromonofluoromethaneSee F027 95—95—4 2,4,5—TrichlorophenolSee P027 88-06—2 2,4,6—TrichlorophenolU234 99—35—4 1,3,5—Trinitrobenzene (R,T)(1182 123—63—7 1, 3,5—Trioxane, 2,4,6—trimethyl—0235 126—72-7 Tris(2,3—dibromopropyl) phosphateU236 72-57-1 Trypan blue15237 66—75—1 Uracil mustard13176 759—73—9 Urea, N—ethyl—N—nitroso-0177 684—93-5 Urea, N-methyl—N—nitroso—0043 75—01-4 Vinyl chloride0248 P 81—81-2 Warfarin, and salts, when present at
concentrations of 0.3% or less0239 1330—20—7 Xylene (I)13200 50—55—5 Yohimban—16—carboxylic acid, 11,17—di—
methoxy-18—[ (3,4, 5—trimethozybenzoyl) —
oxy]—, methyl ester,(3beta, l6beta, i7alpha, l8beta, 20aipha) —
0249 1314—84—7 Zinc phosphide Zn3P2, when present atconcentrations of 10% or less
(Source: Amended at _____ Ill. Reg. _________, effective _________
Section 721.Appendix H Hazardous Constituents
Common Name Chemical Abstracts Name Chemical Hazard-Abstracts ousNumber Waste
Number
Acetonitrile Same 75—05—8 13003Acetophenone Ethanone, 1—phenyl— 98—86—2 00042-Acetylaminofluorene Acetamide, N-9H—fluoren—2— 53—96—3 11005
yl-Acetyl chloride Same 75—36—5 0006l-Acetyl—2—thiourea Acetamide, N— 591—08—2 P002
(aminothioxomethyl )—
Acrolein 2—Propenal 3.07—02 —8 P003Acrylainide 2—Propenamide 79—06—1 U007Acrylonitrile 2-Propenenitrile 107—13—1 U009Aflatoxina Same 1402—68—2
38
Allyl alcoholAllyl chlorideAluminum phosphide
4—Aminobiphenyl5—(Aminomethyl )—3—isoxazolol
4—ArninopyridineArnitroleArnmonium vanadate
AnilineAntimonyAntimony compounds, N.0.S.(not otherwise specified)Aramite
ArsenicArsenic compounds, N.0.S.Arsenic acidArsenic pentoxideArsenic trioxideAur amine
Azaserine
BariumBarium compounds, N.0.S.Barium cyanideBenz(c]acridineBenz(a]anthraceneBenzal chlorideBenmeneBenzerzearsonic acidBenzidine
Benzo(b] fluorantheneBenzo[ j ) fluorantheneBenzo ( k) fluorantheneBenzo(a]pyrenep—Benzoquinone
Benzotrichloride
Benzyl chlorideBeryllium powderBeryllium compounds, N.0S.BromoacetoneBromoform
Propanal, 2-methyl—2—(methylthio)—, 0—[(methylamino) carbonyl ] *
oxime1,4,5, 8-Dimethanonaph—thalene, 1,2,3,4,10,10—hexachloro—1, 4, 4a, 5,8, 8a—hexahydro—, j1—alpha, 4—alpha, 4a—beta, S-alpha, 8—alpha, 8a-beta)—2-Propen—1-ol1—Propene, 3—chioro—Same
[1,1 ‘—Biphenyl]—4—amine3(2H)—Isoxazolone, 5-(aminomethyl) -
4-Pyridinamine1H—1, 2, 4—Triazol—3—amineVanadic acid, ammoniumsaltBenzenamineSame
Sulfurous acid, 2—chloroethyl—, 2—(4—(l, 1—dimethylethyl ) phenoxy 3—1-methylethyl esterArsenic
Arsenic acid Ha3As044Arsenic oxide As2.20S~Arsenic oxide As2.20~Benzenamine, 4,4’—carbon—imidoylbis (N, N—dimethyl—L—Serine, diazoacetate(ester)Same
SameSameSameBenzene, (dichioromethyl) —
SameArsonic acid, phenyl—[1,l’—Biphenyl]—4, 4’—diaxnineBenz (e]acephenanthryleneSameSameSeine2, S—Cyclohexadiene—1, 4—dioneBenzene,(trichloromethyl)—Benzene, (chioromethyl ) —
Same
2 —Propanone, 1 —bromo—Methane, tribromo—
107—18—6107—18—620859—73—892—67—12763—96—4
62—53—3 0012
7440—36—0
140—57—8
115—02—6 13015
7440—39—3
542—62—1225—51—456—SS—398—87—371—43—298—OS—S92—87—S
205—99—2205—82—3207—08—950—32—8106—51—4
98—07—7 (1023
598—31—2 P01775—25—2 U225
Aldicarb
Aldrin
116—06—3 P070
309—00—2 P004
P005
P006
P007
P008U011U119
504—24—561—82—57803—55—6
7440—38—2
7778—39—41303—28—21327—53—3492—80—8
POlOPollP02.213014
P013U01600181301713018
U02 1
002213197
100—44—77440—41—7
P028P015
39
4—Bromophenyl phenyl ether Benzene, 1-bromo-4-- 101-55—3 13030phenoxy-
Brucine Strychnidin—10—one, 2,3— 357—57—3 P018dimethoxy-
Butyl benzyl plzthalate 1,2—Benzenedicarboxylic 85—68—7acid, butyl phenylmethylester
Cacodylic acid Arsenic acid, dimethyl— 75—60—5 Ul36Cadmium Seine 7440-43-9Cadmium compounds, N.0.S.Calcium chromate Chronic acid H2CrO4, 13765—19— U032
calcium salt 0Calcium cyanide Calcium cyanide Ca(CN)2 592—01—8 P021Carbon disulfide Same 75—15—0 P022Carbon oxyf].uoride Carbonic difuoride 353—50-4 11033Carbon tetrachloride Methane, tetrachloro— 56—23—5 0211Chloral Acetaldehyde, trichloro— 75—87—6 13034Chlorambucil Benzenebutanoic acid, 305—03—3 U035
4(bis—(2—chloroethyl)—amino]—
Chlordane 4,7-Methano—1H—indene, 57-74-9 00361,2, 4, 5, 6, 7, 8, 8—octa—chloro—2 , 3,3a,4, 7, la—hexa—hydro-
Chlordane, alpha and gamma 13036isomersChlorinated benzenes, N.O.S.Chlorinated ethane, N.O.S.Chlorinated fluorocarbons,N.0.S.Chlorinated naphthalene,N.o.S.Chlorinated phenol, N.O.S.Chlornaphazine Naphthalenaxnine, N,N’- 494—03-1 U026
bis (2—chloroethyl ) —
Chioroacetaldehyde Acetaldehyde, chloro— 107—20-0 P023Chloroalkyl ethers, N.0.S.p-Chloroaniline Benzenaxnine, 4—chloro- 106-47—8 P024Chiorobennene Benzene, chloro- 108—90—7 13037Chlorobenzi].ate Benzeneacetic acid, 4— 510—15—6 U038
chloro—alpha— (4-chlorophenyl ) —alpha—hydroxy—, ethyl ester
p-Chloro—m-cresol Phenol, 4—chloro—3—methyl- 59—50—7 U0392—Chloroethyl vinyl ether Ethene, (2—ch].oroethoxy)— 110—75—8 15042Chloroform Methane, trichioro— 67-66—3 11044Chloromethyl methyl ether Methane, chloromethoxy— 107—30—2 U046beta—Chloronaphthalene Naphthalene, 2-chioro- 91—58-7 11047o—Chlorophenol Phenol, 2—chloro— 95—57-8 U0481-(o—Chlorophenyl)thiourea Thiourea, (2—chloro— 5344—82—1 P026
phenyl)-Chloroprene l,3—Butadiene, 2-chioro— 126—99—83—Chioropropionitrile Propanenitrile, 3—chloro- 542—76—7 P027Chromium Same 7440—47—3Chromium compounds, N.O.S.Chrysene Same 2 18—01—9 (3050Citrus red No. 2 2—Naphthalenol, 1—[(2,5— 6358—53—8
dmmethoxyphenyl) azo 3—Coal tar creosote Same 8007—45—2Copper cyanide Copper cyanide CuCN 544-92-3 P029Creosote Same (1051Cresols (Cresylic acid) Phenol, methyl— 1319—77—3 U052
40
CrotonaldehydeCyanides (soluble salts andcomplexes), N.0.S.CyanogenCyanogen bromideCyanogen chlorideCycasin
2—Cyclohexyl—4, 6—dinitrophenol
Cyclophosphamide
2,4—D
2,4—D, salts and esters
Dibenz(a,h )acridineDibenz (a, j 3 acridineDibenz( a, h) anthracene7H—Dibenzo f c, g 3 carbazoleDibenzo( a, e]pyrene
Diberizo[a, h]pyreneDibenzo(a, i]pyrene2., 2—Dibromo—3—chloropropane
Dibutyl phthalate
o—Dichlorobenzenem—Dichlorobenzenep—Dich 1 orobenzeneDichlorobenzene, N.O.S.
3,3’ -Dichlorobenzidine
1, 4-Dichloro—2—buteneDichlorodifluoromethaneDichloroethylene, N.0. S.
1, 1-Dichloroethylene1, 2—Dichloroethylene
EthanedinitrileCyanogen bromide (CN)BrCyanogen chloride (CN)ClBeta—D—glucopyranoside,(methyl-ONN-azoxy) methyl-Phenol, 2—cyciohexyl—4,6—dinitro—2H-i, 3, 2-Oxazaphosphorin—2—amine, N,N—bis (2—chioro-ethyl ) tetrahydro—, 2—oxideAcetic acid, (2,4—dichlorophenoxy) —
Acetic acid, (2,4—dichlorophenoxy) —, saltsand esters5, 12-Naphthacenedione, 8-acetyl—10—[ (3—amino—2, 3,6—trideoxy—alpha—L-lyxo-hexopyranosyl)oxy]—7,8, 9, 10—tetrahydro—6,8, 11—trihydroxy—l-meth-oxy—, 8S—cis)—Benzene, 1,1’—(2,2—dichloroethylidene)bis [4-chioro—Benzene, 1,1 ‘—(dichloro—ethenylidene)bis(4-chloro-Benzene, i,1’—(2,2,2—tri—chloroethylidene)bis (4-chioro—Carbaxnothioic acid, bis(1—methylethyl)—, S—(2 , 3—dichloro—2-propenyl) esterSameSeineSameSameNaphtho(l,2,3,4—def]—chryseneDibenzo(b, def 3 chryseneBenzo [ rst ] pentaphenePropane, 1,2-dibromo—3—chloro—1, 2—Benzenedicarboxylicacid, dibutyl esterBenzene, 1, 2—dichloro—Benzene, 1, 3—dichloro—Benzene, 1, 4-dichioro-Benzene, dichloro—
(1,1’—Biphenyl)—4,4’—diamine, 3,3 ‘-dichloro-2—Butene, 1, 4—dichloro-Methane, dichlorodifluoro-Dichloroethylene
Ethene, 1, 1-dichioro—Ethene, 1, 2-dichloro—,(E)—
4170—30—3 U053P030
460—19—5506—68—3506—77—414901-08—7131—89—S
50—18-0
94—75—7 13240
U240
20830—81— 130593
72—55—9
50—29—3 13061
2303—16—4 13062
226—36—8224—42—053—70—3194—59—2192—65—4
189—64—0189—55—996—12—B
84—74—2 (1069
95—50—1541—73—1106—46—725321—22—691—94—i
764—41—075—71—825323—30—275—35—4156—60—S
2-Butertal
P031U246P033
P034
U058
Daunornyc in
DDD
DDE
DDT
Diallate
72—54—8 13060
13063
U064UO66
007013071U072
0073
1307411075
1307813079
4].
Dichloroethyl ether
Dichioroisopropyl ether
Dichloromethoxyethane
Dichloromethyl ether2, 4—Dichlorophenol2, 6—DichiorophenolDichiorophenyl arsine
Dichloropropane, N.0.S.
Dichloropropanol, N.0.S.
Dichioropropene, N.0. S.
1, 3—Dichloropropene
Dieldrin
1,2:3, 4—DiepoxybutaneDiethylarsine1, 4-DiethyleneoxideDiethyihexyl phthalate
N, N’ —Diethyihydrazine0, 0-Diethyl-S-methyl dithio—phosphateDiethyl-p-nitrophenylphosphateDiethyl phthalate
0, 0—Diethyl 0-pyrazinylphosphorothioateDiethylstilbestrol
Dihydrosaf role
Diisopropylfluoropho eph ate(DFP)D imethoate
3,3 ‘—Dimethoxybenzidine
p—Dimethylaminoazobenzene
7, 12-Dimethylbena (a] anthracene
3,3 ‘-Dimethylbenzidine
Dimethylcarbanloyl chloride
1, 1—Diiuethylhydrazine1, 2-Dimethylhydrazine
Ethane, 1,1’-oxybis(2—chloro—Propane, 2,2’-oxybis[2-chioro—Ethane, 1,1’ - (methylene—bis(oxy)bis[2—chloro-Methane, oxybis(chloro-Phenol, 2,4-dichloro-Phenol, 2, 6—dichloro—Arsonous dichioride,phenyl-Propane, dichloro—
Propanol, dichioro-
1—Propene, dichioro-
1—Propene, 1, 3—dichloro—2,7:3, 6—Dimethanonaphth[2,3—b]oxirene,3,4,5,6,9,9—hexachloro—1a, 2,2a, 3,6,6a, 7, 7a-octahydro-,(laalpha, 2beta, 2aalpha,3beta,6beta,6aalpha,7beta,7aalpha) -
2,2’ —BioziraneArsine, diethyl—1 ,4—Dioxane1, 2—Benzenedicarboxy1~cacid, bis (2—ethylhexyl)esterHydrazine, 1, 2—diethyl—Phosphorodithioic acid,0,0—diethyl S—methyl esterPhosphoric acid, diethyl4-nitropheny]. ester1, 2—Benzenedicarboxylicacid, diethy]. esterPhosphorothioic acid, 0,0-diethyl O-pyrazinyl esterPhenol, 4,4’—(1,2—diethyl—1,2—ethenediyl)bis—, (B)—1, 3-Benzodioxole, 5—propyl-Phosphorofluoridic acid,big ( 1-methylethyl) esterPhoaphorodithioic acid,0, 0-dimethyl 5- (2-(methyl—amino)—2-oxoethylj ester(l,1’—Biphenyl)—4,4’—diaxnine, 3,3’ —dimethoxy—Benzenamine, N,N-dimethyl—4—(phenylazo) —
Benz[a]anthracene, 7,12—dimethyl—(l,1’—Biphenyl3—4,4’—diamine, 3,3’ -dimethyl-Carbamic chloride,dimethyl—Hydrazine, 1, 1—dimethyl—Hydrazine, 1, 2—dimethyl-
26638—19—726545—73—326952—23—8542—75—6 U08460—57—1 P037
1615—80—1 13086
3288—58—2 13087
311—45—5 P041
84—66—2 0088
297—97—2 P040
56—53—1 15089
94-58—6 11090
55—91—4 P043
60-51—5 P044
119—90—4 U091
119—93—7 11095
79—44—7 U097
57—14—7 0098540—73—8 13099
111—44—4
108—60—i
11025
U02 7
111—91—1 0024
542—88—1120—83—287—65—0696—28—6
P016U0810082P036
1464—53—5692—42—2123—91—1117—81—7
U08 5P038Ul0813028
60—11—7
57—97—6
U093
13094
42
alpha,alpha-Dimethylphen- Benzeneethanamine, alpha, 122—09-8 P046ethylamine alpha-dimethyl—2,4-Dimethylphenol Phenol, 2,4-dimethyl— 105—67—9 0101Dimethylphthalate 1, 2-Benzenedicarboxylic 131—11—3 11102
acid, dimethyl esterDimethyl sulfate Sulfuric acid, dimethyl 77—78—1 U103
esterDinitrobenzene, N.0.S. Benzene, dinitro— 25154—54—
54,6—Dinitro—o—cresol Phenol, 2—methyl—4,6— 534—52—1 P047
dinitro—4,6—Dinitro—o—cresol salts P0472,4-Dinitrophenol Phenol, 2,4—dinitro- 51-28—5 P0482,4—Dinitrotoluene Benzene, l—methyl-2,4— 121—14—2 13105
dinitro-2,6-Dinitrotoluerie Benzene, 2—methyl-1,3- 606—20—2 0106
dinitro—Dinoseb Phenol, 2—(i— 88—85—7 P020
methylpropyl)-4, 6—dinitro—Di—ri-octyl phthalate 1,2—Benzenedicarboxylic 117—84—0 0107
acid, dioctyl esterDiphenylamine Benzenamine, N-phertyl- 122-39-41,2—Diphenylhydrazine Hydrazine, 1,2-diphenyl- 122—66—7 U109Di—n—propylnitrosamine 1—Propanamine, N—nitroso— 621—64—7 17111
N—propyl-IJisulfoton Phospharodithioic acid, 298—04—4 P039
0,0-diethyl S—(2—(ethyl-thio)ethyl] ester
Dithiobiuret Thioimidodicarbonic 541—53—7 P049diamide ((H~2N)C(S))~NH
Endosulfan 6, 9—Methano—2,4,3—benzo— 115—29—7 P050dioxathiepen,6, 7,8,9,10,1O—hexachloro—l, 5, Sa, 6,9,9a-hexahydro-, 3-oxide,
Endothal 7— 145—73—3 P088Oxabicyclo (2.2 • 1] heptane—2, 3—dicarboxylic acid
Endrin 2,7:3, 6—Dimethanonaphth— 72—20—8 P051(2,3—b]oxirene, 3,4,5,6,9,9—hexachioro-la, 2, 2a, 3,6,6a, 7, 7a—octahydro—, (1aalpha, 2beta, 2abeta, 3alpha,Galpha,Gabeta,7beta,7aalpha)—,
Eadrin metabolites P051Epichlorohydrin Oxirane, (chloromethyl)— 106-89—8 (1041Epinephrine l,2—Benzenediol, 4-(1— 51—43-4 P042
hydroxy—2- (methylamino ) -
ethyl]—, (R)—Ethyl carbamate (urethane) Carbamic acid, ethyl ester 51—79—6 U238Ethyl cyanide Propanenitrile 107—12-0 P101Ethylenebisdithiocarbamic acid Carbamodithioic acid, 1,2— 111—54—6 11114
ethanediy].bis—Ethylenebisdithiocarbamic 11114acid, salts and estersEthylene dibromide Ethane, i,2-dibromo— 106—93—4 13067Ethylene dichloride Ethane, 1,2-dichloro— 107—06-2 13077Ethylene glycol monoethyl Ethanol, 2—ethoxy- 110-80-5 13359etherEthyleneimine Aziridine 151—56-4 POS4Ethylene oxide Oxirane 75—21—8 13115Ethylenethiourea 2—Imidazolidinethione 96—45—7 U1l6
43Ethylidine dichloride
Ethyl methacrylate
Ethyl methanesulfonate
Famphur
PluorantheneFluorineFluoroacetamidePluoroacetic acid, sodium salt
FormaldehydeFormic acidGlycidylaldehydeHalomethanee, N.O.S.Heptachlor
Heptachlor epoxide
Heptachlor epoxide (alpha,beta4 and gamma isomers)HeptachlorodibenzofuransHeptachlorodibenzo—p-diox insHexachlorobenzeneHexachlorobutadiene
Hexachlorocyclo-pentadiene
Hexachlorodibenzo-p-dioxinsHexachlorodibenzofuransHexachloroethaneHexachlorophene
Hexachloropropeae
Hexaethyltetraphosphate
BydrazineHydrogen cyanideHydrogen fluorideHydrogen sulfideIndeno[1,2 , 3-cd]pyreneIsobutyl alcoholIsodrin
Ethane, 1, 1-dichioro—2—Propenoic acid, 2—methyl-, ethyl esterMethaneaulfonic acid,ethyl esterPhosphorothioc acid, 0—[4-[(dimethylamino) sulfonyl]—phenyl] 0,0-dimethyl esterSameSameAcetamide, 2—f luoro—Acetic acid, fluoro—,sodium saltSameSeineOxiranecarboxaldehyde
4,7—Met hano—1H—indene, 1,4,5,6, 7,8,8-heptachloro—3a,4,7, 7a—tetrahydro—2, 5—Methano-2H-indeno[ 1,2bjoxirene, 2,3,4,5,6, 7,7—heptachloro—1a, ib, 5, 5a, 6,6a-hexahydro—, (laalpha, lbbeta, 2alpha, 5alpha, Sabeta,6beta, 6aalpha) —
Ethane, hexachioro—Phenol, 2,2 ‘—methylene—bis[3, 4, 6—trichioro—1—Propene, 1,1,2,3,3,3—hexachloro—Tetraphosphoric acid,hexaethyl esterSameHydrocyanic acidHydrofluoric acidHydrogen sulfide H2SSamei—Propanol, 2—methyl—1,4:5, 8—Dimethanonaph—thalene, 1,2,3,4,10, 10—hexachloro—1, 4, 4a, 5,8, 8a—hexahydro—, (lalpha,4alpha, 4abeta, Sbeta, Bbeta,8abeta)—,1, 3—Benzodioxole, 5—(1—propenyl) —
1,3, 4-Hetheno—2H—cyclo—butafcd]pentalen—2—one,1, Ia, 3, 3a, 4, 5,5, Sa, Sb, 6—decachlorooctahydro—,
75—34—3
97—63—2
62—50—0
52—85—7 P097
12.8—74—1 Ul2787—68—3 11128
77—47—4 13130
67—72—1 U131
70—30—4 11132
1888—71.-7 0243
757—58—4 P062
13076
U118
13119
206—44—07782—41—4640—19—762—74—8
50—00—064—18—16765—34—4
U120P056P057P058
0122(3123U12 6
76—44—8 P059
1024—57—3
Benzene, hexachloro—1, 3—Butadiene,1,1,2,3,4, 4—hexachloro—1, 3-Cyclopentadiene,1,2,3,4, 5,5—hexachioro—
302—01—274—90—87664—39—37783—06—4193—39—578—83—1465—73—6
Isosaf role
Kepone
U133P063131341113501370140P060
120—58-1 0141
143—50”0 U142
44
Lasiocarpine 2-Butenoic acid, 2-methyl— 303—34—1 U1437-([2,3—dihydroxy-2—(1-
methoxyethyl) -3—methyl—i—oxobutoxy]methyl]—2 ,3,5,7 a-tetrahydro-1H-pyrrol—izin—l—yl ester, (1S—(1—alpha(Z),7(2S*,3R*),laalpha] 3—
Lead Same 7439—92—1Lead and compounds, N.0.S.Lead acetate Acetic acid, lead (2+) 301—04—2 (1144
saltLead phosphate Phosphoric acid, lead (2+) 7446—27-7 13145
salt (2:3)Lead eubacetate Lead, bis(acetato-0)tetra— 1335—32—6 13146
hydroxytri-Lindane Cyclohexane, 1,2,3,4,5,6— 58—89—9 U129
hexachloro—, ialpha,2alpha, 3beta, 4alpha,Salpha, 6beta)—
Maleic anhydride 2,5—Purandione 108—31-6 13147Maleic hydrazide 3,6—Pyridazinedione, 1,2— 123—33—1 13148
dihydro-Malononitrile Propanedinitrile 109—77-3 Ul49Melphalan L—Phenylalanine, 4-(bis(2— 148—82—3 0150
chloroethyl) amino] -
Mercury Same 7439—97-6 UlSlMercury compounds, N.0.S.Mercury fulminate ~‘ulminic acid, mercury 628—86—4 P065
(2+) saltMethacrylonitrile 2—Propenenitrile, 2— 126—98—7 Ul52
methyl—Methapyrilene 1,2—Ethanediamine, N,N— 91—80-5 Ul55
dimethyl—N’ —2-pyridinyl—N’ - (2-thienylmethyl ) -
Metholniyl Ethanimidothioic acid, N— 16752—77— P066(((methyl— 5amino)carbonyl]oxy]—,methyl ester
I.lethoxychlor Benzene, 1,l’—(2,2,2— 72—43—5 11247trichloroethylidene)bis [4—methaxy—
Methyl bromide Methane, bromo- 74-83—9 13029Methyl chloride Methane, chloro— 74—87—3 13045Methylchlorocarbonate Carbonochloridic acid, 79-22—1 11156
methyl esterMethyl chloroform Ethane, 1,1,l—trichloro— 71—55-6 112263—Methyloholanthrene Benz[j]aceanthrylene, 1,2— 56—49—S 11157
dihydro—3 —methyl—4,4’—Methylenebis(2—chloro— Beazenarnine, 4,4’— 2.01—14—4 U158aniline) methylenebis (2-chloro—Methylene bromide Methane, dibromo- 74-95—3 13068Methylene chloride Methane, dichloro— 75—09—2 0080Methyl ethyl ketone (MEK) 2-Butanone 78—93—3 0159Methyl ethyl ketone peroxide 2-Butanone, peroxide 1338—23-4 (1160Methyl hydrazine Bydrazine, methyl— 60—34—4 P068Methyl iodide Methane, iodo— 74—88—4 11138Methyl isocyanate Methane, isocyanato— 624—83—9 P0642-I4ethyllactonitrile Propanenitrile, 2-hydroxy- 75—86—5 P069
2-methyl—Methyl rnethacrylate 2-Propenoic acid, 2— 80—62-6 0162
methyl—, methyl ester
45
Methyl methanesulfonate Methanesulfonic acid, 66—27-3methyl ester
Methyl parathion Phosphorothioic acid, 0,0— 298—00-0 P071dimethyl 0- (4—nitrophenyl)ester
Methylthiouracil 4—(1R)—Pyrimidinone, 2,3— 56—04—2 11164dihydro— 6—methyl—2-thioxo-
Mitomycin C Azirino(2’, 3’:3, 50—07—7 U0i04 ]pyrrolo( 1, 2—a] indole—4,7—dione, 6-amino-8—(~aminocarbonyl)oxy)-znethyl]—i, la,2,8,8a,8b—hexahydro-8a-methoxy—5 —
methyl—, [la—S— (laalpha,Sbeta, 8aalpha, 8balpha) 3—,
MNNG Guanidine, N-methyl—N’- 70-25—7 11163nitro—N—nitroso—
Mustard gas Ethane, i,1’-thiobis[2- 505—60—2 132.65chioro—
Naphthalene Same 9 1—20—3 01651, 4-Naphthoquinone 1, 4-Naphthalenedione 130—15-4 0166alpha-Naphthylaniine 1-Naphthaleaainine 134—32-7 U167beta—Naphthylamine 2-Naphthalenaxnine 91-59—8 13168alpha—Naphthylthiourea Thiourea, 1—naphthalenyl— 86—88—4 P072Nickel Same 7440-02—0Nickel compounds, N.0.S.Nickel carbonyl Nickel carbonyl Ni(C0)4, 13463—39— P073
(T—4)— 3Nickel cyanide Nickel cyanide Ni(CN)2 557—19—7 P074Nicotine Pyridine, 3—(1—methyl—2— 54—11—5 P075
pyrrolidinyl)—, (S)—Nicotine salts P075Nitric oxide Nitrogen oxide NO 10102—43— P076
9p-Nitroaniline Benzenamine, 4—nitro- 100-01—6 P077Nitrobenzene Benzene, nitro- 98—95—3 P078Nitrogen dioxide Nitrogen oxide NO2 10102—44— P078
0Nitrogen mustard Ethanamine, 2-chloro-N—(2- 51—75-2
chloroethyl) —N—methyl—Nitrogen mustard, hydro-chloride saltNitrogen mustard N-oxide Ethanamine, 2-chloro—N--(2— 126-85—2
chloroethyl) -N-methyl-, N-oxide
Nitrogen mustard, N-oxide,hydrochloride saltNitroglycerin 1,2,3—Propanetriol, 55—63—0 P081
trinitratep—Nitrophenol Phenol, 4—nitro— 100—02—7 111702—Nitropropane Propane, 2—nitro— 79—46—9 0171Nitrosarninea, N.O.S. 35576—91—
1N—Nitrosodi—n-buty].arnine 1—Butanamine, N-butyl-N— 924—16—3 Ul72
nitroso—N—Nitrosodiethanolaxnine Ethanol, 2,2’—(nitroso— 1116—54—7 0173
ixnino)bis—N—Nitrosodiethylamine Ethanainine, N—ethyl-N— 55—18—5 Ui74
nitroso—N—Nitrosodimethylamine Nethanamine, N—methyl-N- 62-75—9 P082
nitroso—N-Mitroao-N—ethylurea Urea, N—ethyl-N-nitroao- 759—73—9 13176
46
N-Nitrosomethylethylamine Ethanarnine, N-methyl-N- 10595—95—nitroso— 6
N—Nitroso—N-methylurea Urea, N—methyl—N-nitroso— 684—93—S U177N—Nitroso—N-methylurethane Carbamic acid, 615—53—2 15178
methylnitroso-, ethylester
N-Nitroaomethylvinylamine Vinylamine, N—methyl-N- 4549—40-0 P084nitroso-
N—Nitrosomorpholine Morpholine, 4-nitroso— 59—89—2N—Nitroaonornicotine Pyridine, 3- ( 1—nitroso-2— 3.6543—55—
pyrrolidinyl)—, (5)— 8N—Nitrosopiperidine Piperidine, 1-nitroso— 100—75—4 0179N—Mitrosopyrrolidine Pyrrolidine, 1—nitroso- 930-55-2 (1180N—Nitrososarcosine Glycine, N—methyl—N- 13256—22-
nitroso— 95—Nitro-o-toluidine Benzenamine, 2-methyl—5— 99—55—8 U181
nitro-Octamethylpyrophosphoramide Diphosphoramide, 152 -16—9 P08S
octamethyl—Osmium tetroxide Osmium oxide 0s04, (T-4) 20816—12- P087
0Paraldehyde 1,3,5—Trioxane, 2,4,6—tn— 123-63—7 U1B2
methyl—Parathion Phosphorothioic acid, 0,0- 56—38-2 P089
diethyl 0- (4-nitrophenyl)ester
Pentachlorobenzene Benzene, pentachloro— 608—93—S U183Pentachlorodibenzo-p-dioxinsPentachlorodibenzofuransPentachloroethane Ethane, pentachloro- 76—01—7 U184Pentachloronitrobenzene (PCNB) Benzene, pentachioronitro— 82—68—8 13185Pentachiorophenol Phenol, pentachloro— 87—86—S See
P027Phertacetin Acetainide, N—(4— 62—44—2 15187
ethoxyphenyl ) —
Phenol Same 108—95—2 11188Phenylenediamine Benzenediamine 25265—76—
3Phenylxnercury acetate Mercury, (acetato- 62—38—4 P092
O)phenyl—Phenylthiourea Thiourea, phenyl— 103—85—5 P093Phoagene Carbonic dichloride 75—44—5 P095Phosphine Same 7803—51—2 P096Phorate Phosphorodithioic acid, 298—02—2 P094
O,O-diethyl S—((ethylthio)methyl) ester
Phthalic acid esters, N..O.S.Phthalic anhydride 1,3—Isobenzofurandione 85—44—9 Ul902—Picoline Pyridine, 2-methyl— 109—06—8 U191Polychlorinated biphenyls,N.O.S.Potassium cyanide Same 151—50—8 P098Potassium silver cyanide Argentate(1—), bis(cyano— 506—61—6 P099
C)—, potassium)Potassium i,entachlorophenate Peritachlorophenol, 7778736 None
i~otassium saltPronamide Benzamide, 3,5—dichloro—M— 23950—58— 112.92
(1, l—dimethyl-2-propynyl) - S1,3—Propane aultone 1,2—Oxathiolane, 2,2— 1120—71—4 13193
dioxiden-Propylamine 1—Propanarnine 107—10—8 13194Propargy]. alcohol 2—Propyn-1—ol 107—19—7 P102
47
Propylene dichloride1, 2-PropyleniminePropylthiouracil
Pyrid meReserpine
ResorcinolSaccharin
Saccharin saltsSaf role
SeleniumSelenium compounds,Selenium dioxideSelenium sulfideSelenoureaSilverSilver compounds, N.O.S.Silver cyanideSilvex (2,4,5—TP)
Sodium cyanideSodium ientachloronhenate
Streptozotoc in
StrychnineStrychnine saltsTCDD
1,2,4, 5—Tetrachlorobenzene
Tetrachlorodibenzo—p-dioxinsTetrachlorodibenzofuransTetrachioroethane, N.O. S.
1,1,1, 2—Tetrachioroethane
1,1,2, 2—Tetrachloroethane
Tetrachloroethylene
2,3,4, 6—Tetrachlorophenol
2,3,4, 6—Tetrachiorophenol,potassium salt2,3,4, 6—Tetrachlorophenol,sodium saltTetraethyldithiopyrophosphate
Tetraethyl leadTetraethylpyrophosphate
TetranitromethaneThalliumThallium compounds
Propane, 1, 2-dichioro-Aziridine, 2—methyl—4 (1H)—Pyrimidinone, 2,3—dihydro- 6-propy 1. -2—thioxo-SameYohimban—l6—carboxyl icacid, 11, i7—dimethoxy—l8—((3,4,5-trimethoxy—benzoyl )oxy3-, methylester, (3beta, l6beta,l7alpha, l8beta, 2oalpha)—,1,3—Benzenediol1, 2—Benzisothiazol—3 (2H) -
one, 1,1—dioxide
1,3—Benzodioxole, 5—(2—propenyl)—Same
Se].enioua acidSelenium sulfide SeS2SameSame
Silver cyanide AgCNPropanoic acid, 2—(2,4,5—trichlorophenoxy) —
Sodium cyanide NaCNPentachiorophenol, sodiumsaltD—Glucose, 2—deoxy—2—[~methylnitrosoamino)ca—rbonyljamino]—Strychnidin—lO-one
Dibenzo(b,e][l,4]dioxin,2,3,7, 8—tetrachloro—Benzene, 1,2,4,5—tetrachloro—
Ethane, tetrachloro—,NO.5.Ethane, 1,1,1,2—tetrachioro—Ethane, 1,1,2,2—tetrachloro—Ethene, tetrachloro—Phenol, 2,3,4,6—tetrachloro—Same
Same
Thiodiphosphoric acid,tetraethy]. esterPlumbane, tetraethyl-Diphosphoric acid,tetraethyl esterMethane, tetranitro—Same
0083P067
108—46—3 1120181—07—2 15202
1120294—59—7 0203
7782—49—2
7783—00—87488—56—4630—10—47440—22—4
57—24—9 P108P108
1746—01—6
95—94—3 11207
25322—20—7630—20—6 U208
79—34—5 13209
127—18—4 U21058—90—2 See
P02753535276 None
25567559 None
3689—24—5 P109
78—00—2 P110107—49—3 P111
509—14—8 P1127440—28—0
78—87—575—55—851—52—S
110—86—150—55—S
U1960200
N.O.S.020413205P103
P104SeeF02 7P106None
U206
506—64—993—72—1
143—33—9131522
18883—66—4
48Thallic oxide
Thallium (I) acetate
Thallium (I) carbonate
Thallium (I) chlorideThallium (I) nitrate
Thallium selenite
Thallium (I) sulfate
Thioacetarnide
Thiofanox
ThiomethanolThiophenolThiosemicarbazideThioureaThirain
Toiuene
Toluenediamine
Toluene—2 , 4-diamine
Toluene—2 , 6—diamine
Toluene—3, 4—diamine
Toluene diisocyanate
o—Toluidineo-Toluidine hydrochloride
p-ToluidineToxaphene1,2, 4—Trichlorobenzene1,1, 2—TrichioroethaneTrichloroethyleneTr ichloromethanethiolTr ichloromonofluoromethane2,4, 5—Trichiorophenol
2,4, 6-Trichlorophenol
2,4,5—T
Trichioropropane, N ~0. S.
1,2, 3-Tnichloropropane0,0, O—Triethylphosphorothioate
1,3, 5—TrinitrobenzeneTris ( l—aziridinyi ) phosphinesulfideTria (2, 3—dibromopropyl)phosphate
Thallium oxide Tl203Acetic acid, thallium (1+)saltCarbonic acid, dithallium(1+) saltThallium chloride T1C1Nitric acid, thallium (1+)saltSelenious acid, dithallium(1+) saltSulfuric acid, dithallium(1+) saltEthanethioamide2—Butanone, 3, 3-dimethyl—1—(methylthio) —, 0—[(methylamino) carbonyl) -
oximeMethanethiolBenzenethiolHydraziriecarbothioamideSameTh ioperoxydicarbonicdiamide ((H2N)C(S) 12S2,tetramethyl-Benzene, methyl—Benzenediamine, ar—methyl—
1, 3’-Benzenediaxnine, 4—methyl-1,3—Benzenediamirie, 2—methyl-1, 2—Benzenediarnine, 4—methyl-Benzene, 1, 3—diisocyanato—methyl—Benzenamine, 2—methyl—Benzeneamine, 2—methyl—,hydrochlorideBenzenaxnine, 4—methyl-SameBenzene, 1,2, 4—trichioro—Ethane, 1, l,2—trichloro—Ethene, trichloro—Methanethiol, trichioro—Methane, trichlorof2.uoro—Phenol, 2,4, 5—trichloro—
Phenol, 2,4, 6—trichloro—
Acetic acid, (2,4,5—
trichlorophenoxy) —
Propane, 1,2, 3—trichloro—Phosphorothioic acid,O,O,O-triethy]. esterBenzene, 1,3, 5—trinitro—Azinidine, 1,1’, 1”—phos—phinothioyl idynetris—l—Propanol, 2, 3—dibromo—,phosphate (3:1)
6533—73—9 U2l5
7791—12—010102—45—112039—52—07446—18—6
62—55—S39196—18—4
108—88—325376—45—895—80—7
823—40—5
496—72—0
26471—62—59S—53—4636—21—5
106—49—08001—35—2120—82—179—00—S U22779—01—6 1122875—70—7 P11875—69—4 1112195—95—4 See
P02788—06—2 See
P02793—76—5 See
P02725735—29—996—18—4126—68—1
99—35—4 1523452—24—4
126—72—7 (3235
1314—32—S563—68—8
P11311214
74—93—1108—98—S79—19—662—56—6137—26—8
U216
0217
P114
P2.15
11218
P045
13153P014P116P2190244
U22 013221
U2 23
1132813222
17353P123
49
Vanadium pentoxideVinyl chlorideWart arm
Warfarin salts, when presentat concentrations less than0.3%.Warfarin salts, when presentat concentrations greater than0.3%.Zinc cyanideZinc phosphide
Zinc phosphide
(Source: Amended at
2, 7—Naphthalenedisulfonicacid, 3,3’—((3,3’—dimethyl [ 1,1’ —biphenyl] -
4, 4’—diyl)bis(azo}]bis[5—axnino-4-hydroxy-,tetrasodium salt2,4—(lH,3H)—Pyrimidinedione, 5-(bis(2-chloroethyl) amino)-Vanadium oxide V205Ethene, chloro—2H-1-Benzopyran—2—one, 4—hydroxy-3- (3-oxo-1-phenyl-butyl)-, when present atconcentrations less than0.3%.2H—2.-Benzopyran—2—one, 4—hydroxy-3— ( 3-oxo—1--phenyl—butyl)-, when present atconcentrations greaterthan 0.3%.
Zinc cyanide Zn(CN)2Zinc phosphide P2Zn:, whenpresent at concentrationsgreater than 10%.Zinc phosphide P2Zn3, whenpresent at concentrationsof 10% or less.
Ill. Reg. _________, effective
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE 3: WASTEDISPOSAL
CHAPTER I: POLLUTION CONTROLBOARDSUBCHAPTERC: HAZARDOUSWASTE OPERATING REQUIREMENTS
PART 724STANDARDSFOR OWNERSAND OPERATORSOF HAZARDOUSWASTE
TREATMENT, ST0RAGE~AND DISPOSAL FACILITIES
SUBPARTA: GENERALPROVISIONS
Purpose, Scope and ApplicabilityRelationship to Interim Status Standards
Trypan blue
Uracil mustard
72—57—1 13236
66—75—1 U237
War farm
1314—62—175—01—481—81—2
P12011043U248
81—81—2 P001
U248
Pool
P121P122
557—21—1132.4—84—7
1314—84—7 U249
Section724.101724.103
Sect ion724. 110724.111724.112724.113724.114724. 115724. 116
SUBPART B: GENERAL FACILITY STANDARDS
ApplicabilityIdentification NumberRequired NoticesGeneral Waste AnalysisSecurityGeneral Inspection RequirementsPersonnel Training
50
724.2.17 General Requirements for Ignitable, Reactive or IncompatibleWastes
724.118 Location Standards724.119 Construction Quality Assurance Program
SUBPART C: PREPAREDNESSAND PREVENTIONSection724.130 Applicability724.131 Design and Operation of Facility724.132 Required Equipment724.133 Testing and Maintenance of Equipment724.134 Access to Communications or Alarm System724.135 Required Aisle Space724.137 Arrangements with Local Authorities
SUBPART D: CONTINGENCYPLAN AND EMERGENCYPROCEDURESSection724.150 Applicability724.151 Purpose and Implementation of Contingency Plan724.152 Content of Contingency Plan724..153 Copies of Contingency Plan724.154 Amendment of Contingency Plan724.155 Emergency Coordinator724.156 Emergency Procedures
SUBPART E: MANIFEST SYSTEM, RECORDKEEPINGAND REPORTINGSection724. 170 Applicability724.171 Use of Manifest System724.172 Manifest Discrepancies724.173 Operating Record724.174 Availability, Retention and Disposition of Records724.175 Annual Report724.176 Unmanifeated Waste Report724.177 Additional Reports
SUBPART F: RELEASES PROMSOLID WASTE MANAGEMENTUNITSSect ion724.190 Applicability724.191 Required Programs724.192 Groundwater Protection Standard724.193 Hazardous Constituents724.194 Concentration Limits724.195 Point of Compliance724.196 Compliance Period724.2.97 General Groundwater Monitoring Requirements724.198 Detection Monitoring Program724.199 Compliance Monitoring Program724.200 Corrective Action Program724.201 Corrective Action for Solid Waste Management Units
SUBPART C: CLOSUREAND POST-CLOSURESection724.210 Applicability724.211 Closure Performance Standard724.22.2 Closure Plan; Amendment of Plan724.213 Closure; Time Allowed For Closure724.22.4 Disposal or Decontamination of Equipment, Structures and Soils724.215 Certification of Closure724.216 Survey Plat724.217 Post-closure Care and Use of Property724.218 Post-closure Plan; Amendment of Plan
51
724.219 Post—closure Notices724.220 Certification of Completion of Post—closure Care
SUBPART H: FINANCIAL REQUIREMENTSSection724.240 Applicability724.241 Definitions of Terms As Used In This Subpart724.242 Cost Estimate for Closure724.243 Financial Assurance for Closure724.244 Cost Estimate for Post—closure Care724.245 Financial Assurance for Post—closure Care724.246 Use of a Mechanism for Financial Assurance of Both Closure and
Post—closure Care724.247 Liability Requirements724.248 Incapacity of Owners or Operators, Guarantors or Financial
Institutions724.251 Wording of the Instruments
SUBPART I: USE AND MANAGEMENTOF CONTAINERSSection724.270 Applicability724.271 Condition of Containers724.272 Compatibility of Waste With Container724.273 Managementof Containers724.274 Inspections724.275 Containment724.276 Special Requirements for Ignitable or Reactive Waste724.277 Special Requirements for Incompatible Wastes724.278 Closure
SUBPARTJ: TANK SYSTEMSSection724.290 Applicability724.291 Assessment of Existing Tank System’s Integrity724.292 Design and Installation of New Tank Systems or Components724.293 Containment and Detection of ReleaBes724.294 General Operating Requirements724.295 Inspections724.296 Response to Leaks or Spills and Disposition of Leaking or unf it—
for—use Tank Systems724.297 Closure and Post—Closure Care724.298 Special Requirements for Ignitable or Reactive Waste724.299 Special Requirements for Incompatible Wastes724.300 Special Requirements for Hazardous Wastes P020, P021, P022, P023,
F026 and F027
SUBPART K: SURFACEIMPOUNDMENTSSection724.320 Applicability724.321 Design and Operating Requirements724.322 Action Leakage Rate724.323 Response Actions724.326 Monitoring and Inspection724.327 Emergency Repairs; Contingency Plans724.328 Closure and Post-closure Care724.329 Special Requirements for Ignitable or Reactive Waste724.330 Special Requirements for Incompatible Wastes724.331 Special Requirements for Hazardous Wastes F020, F021, F022, P023,
F026 and F027
SUBPART L: WASTE PILESSection
52
724.350 Applicability724.351 Design and Operating Requirements724.352 Action Leakage Rate724.353 Response Action Plan724.354 Monitoring and Inspection724.356 Special Requirements for Ignitable or Reactive Waste724.357 Special Requirements for Incompatible Wastes724.358 Closure and Post-closure Care724.359 Special Requirements for Hazardous Wastes P020, P021, P022, F023,
F026 and P027
SUBPART M: LAND TREATMENTSection724.370 Applicability724.371 Treatment Program724.372 Treatment Demonstration724.373 Design and Operating Requirements724.376 Food—chain Crops724.378 Unsaturated Zone Monitoring724.379 Recordkeeping724.380 Closure and Post-closure Care724.381 Special Requirements for Ignitable or Reactive Waste724.382 Special Requirements for Incompatible Wastes724.383 Special Requirements for Hazardous Wastes F020, F021, P022, P023,
P026 and P027
SUBPART N: LANDFILLSSection724.400 Applicability724.401 Design and Operating Requirements724.402 Action Leakage Rate724.403 Monitoring and Inspection724.404 Response Actions724.409 Surveying and Recordkeeping724.410 Closure and Post—closure Care724.412 Special Requirements for Ignitable or Reactive Waste724.413 Special Requirements for Incompatible Wastes724.414 Special Requirements for Bulk and Containerized Liquids724.415 Special Requirements for Containers724.416 Disposal of Small Containers of Hazardous Waste in Overpacked
Drums (Lab Packs)724.417 Special Requirements for Hazardous Wastes P020, F021, F022, F023,
P026 and F027
SUBPART0: INCINERATORSSection724.440 Applicability724.441 Waste Analysis724,442 Principal Organic Hazardous Constituents (POHCS)724.443 Performance Standards724.444 Hazardous Waste Incinerator Permits724.445 Operating Requirements724.447 Monitoring and Inspections724.451 Closure
SUBPART S: CORRECTIVE ACTION FOR SOLID WASTE MANAGEMENTUNITSSection724.652 Corrective Action Management Units724.653 Temporary Units
SUBPART W: DRIP PADSSect ion
53
ApplicabilityAssessment of existing drip pad integrityDesign and installation of new drip padsDesign and operating requirementsInspectionsClosure
SUBPART X: MISCELLANEOUSUNITS
ApplicabilityEnvironmental Performance StandardsMonitoring, Analysis, Inspection, Response, Reporting andCorrective ActionPost—closure Care
SUBPART AR: AIR EMISSION STANDARDSFOR PROCESSVENTS
Control Devices
SUBPART BB: AIR EMISSION STANDARDSFOR EQUIPMENTLEAKS
ApplicabilityDefinitionsStandards:Standards:Standards:Standards:Standards:Standards:Standards:ConnectorsStandards: Delay of RepairStandards: Closed—vent Systems and Control DevicesAlternative Percentage Standard for ValvesSkip Period Alternative for ValvesTest Methods and ProceduresRecordkeeping RequirementsReporting Requirements
ApplicabilityDesign and operating standardsClosure and post—closure care
Recordkeeping InstructionsEPA Report Form and Instructions (Repealed)Cochran’s Approximation to the Behrens—FisherTestExamples of Potentially Incompatible WasteGroundwater Monitoring List
AUTHORITY: Implementing Section 22.4 and authorized by Section 27 of theEnvironmental Protection Act (Ill. Rcv. Ctat. 1901, ch. 111½, pars. 1022.4- and1027- (415 ILCS 5/22.4 and 27)-).
ApplicabilityDefinitionsStandards: Process VentsStandards: Closed-vent Systems andTest methods and proceduresRecordkeeping requirementsReporting Requirements
724. 670724. 671724. 672724, 673724. 674724. 675
Section724.700724. 701724. 702
724. 703
Section724. 930724.931724. 932724. 933724. 934724. 935724. 936
Section724. 9 50724. 951724. 952724. 953724. 954724. 955724. 9 56724. 9 57724. 958
724. 959724. 960724. 961724. 962724. 963724. 964724. 965
Section724.1100724.3.101724.1102
Pumps in Light Liquid ServiceCompressorsPressure Relief Devices in Gas/Vapor ServiceSampling Connecting SystemsOpen—ended Valves or LinesValves in Gas/Vapor or Light Liquid ServicePumps, Valves, Pressure Relief Devices and Other
SUBPART DD: CONTAINMENTBUILDINGS
724.Appendix A724.Appendix B724.Appendix 13
724.Appendix B724.Appendix I
Student’s T-
54
SOURCE: Adopted in R82—19, 53 PCB 131, at 7 Ill. Reg. 2.4059, effectiveOctober 12, 1983; amended in R84—9 at 9 Ill. Reg. 11964, effective July 24,1985; amended in R85—22 at 10111. Reg. 1136, effective January 2, 2.986;amended in R86—l at 10 Ill. Reg. 14119, effective August 12, 1986; amended inR86—28 at 11 Ill. Reg. 6138, effective March 24, 1987; amended in R86—28 at 11Ill. Reg. 8684, effective April 21, 1987; amended in R86—46 at 11 Ill. Reg.13577, effective August 4, 1987; amended in R87—5 at 11 Ill. Reg. 19397,effective November 12, 1987; amended in R87—39 at 12 Iii. Reg. 13135,effective July 29, 1988; amended in R88—16 at 13 Ill. Reg. 458, effectiveDecember 28, 1988; amended in R89—1 at 13 Ill. Reg. 18527, effective November13, 1989; amended in R90—2 at 14 Ill. Reg. 14511, effective August 22, 1990;amended in R90—1Oat 14 Ill. Reg. 16658, effective September 25, 1990; amendedin R90—11 at 15 Ill. Reg. 9654, effective June 17, 1991; amended in R91-1 at15 Ill. Req. 14572, effective October 1, 1991; amended in R91—13 at 16 Ill.Req. 9833, effective June 9, 1992; amended in R92—1 at 16 Ill. Req. 17666,effective November 6, 1992; amended in R92—lO at 17 Ill. Reg. 5806, effectiveMarch 26, 1993; amended in R93—4 at 17 Ill. Req. 20830, effective November 22,1993; amended in R93—16 at 18 Ill. Reg. 6973, effective April 26, 1994;amended in R94—7 at 18 Ill. Reg. 12487, effective July 29, 1994; amended inR94—17 at Ill. Req. , effective
SUBPART 0: CONTINGENCYPLAN AND EMERGENCYPROCEDURES
Section 724.152 Content of Contingency Plan
a) The contingency plan must describe the actions facility personnelmust take to comply with Section~ 724.151 and Scotion- 724.156 inresponse to fires, explosions~ or any unplanned sudden ornon—sudden release of hazardous waste or hazardous wasteconstituents to air, soil~ or surface water at the facility.
b) If the owner or operator has already prepared a Spill PreventionrControl and Countermeasures (SPCC) Plan in accordance with 40 CFRPart 112 or 15103.QQ, or some other emergency or contingency plan,the owner or operator need only amend that plan to incorporatehazardous waste management provisions that are sufficient tocomply with the requirements of this Part.
C) The plan must describe arrangements agreed to by local policedepartments, fire departments, hospitals, contractors~ and stateand local emergency response teams to coordinate emergencyservices pursuant to Section 724.137.
d) The plan must list names, addresses~ and phone numbers (office andhome) of all persons qualified to act as emergency coordinator(see Section 724.155), and this list must be kept up to date.Where more than one person is listed, one must be named as primaryemergency coordinator and others must be listed in the order inwhich they will assume responsibility as alternates. For newfacilities, this information must be supplied to the Agency at thetime of certification, rather than at the time of permitapplication.
e) The plan must include a list of all emergency equipment at thefacility [such as fire extinguishing systems, spill controlequipment, communications and alarm systems (internal andexternal) and decontamination equipment], where this equipment isrequired. This list must be kept up to date. In addition, theplan must include the location and a physical description of eachitem on the list, and a brief outline of its capabilities.
55
f) The plan must include an evacuation plan for facility personnelwhere there is a possibility that evacuation could be necessary.This plan must describe signal(s) to be used to begin evacuation,evacuation routes and alternate evacuation routes (in cases wherethe primary routes could be blocked by releases of hazardous wasteor fires).
(Source: Amended at _____ Ill. Req. ________, effective
Section 724.156 Emergency Procedures
a) Whenever there is an imminent or actual emergency situation, theemergency coordinator (or the designee when the emergencycoordinator is on call) muctshall immediately:
1) Activate internal facility alarms or communication systems,where applicable, to notify all facility personnel; and
2) Notify appropriate state or local agencies with designatedresponse roles if their help is needed.
b) Whenever there is a release, fire4, or explosion, the emergencycoordinator muatshall immediately identify the character, exactsource, amount4, and areal extent of any released materials. Theemergency coordinator may do this by observation or review offacility records or manifests, and, if necessary, by chemicalanalysis.
C) Concurrently, the emergency coordinator muatahall assess possiblehazards to human health or the environment that may result fromthe release, fire4, or explosion. This assessment must considerboth direct and indirect effects of the release, fire.,, orexplosion (e.g., the effects of any toxic, irritating,, orasphyxiating gases that are generated, or the effects of anyhazardous surface water run—off from water or chemical agents usedto control fire and heat—induced explosions).
d) If the emergency coordinator determines that the facility has hada release, fire,, or explosion whichthat could threaten humanhealth, or the environment, outside the facility, the emergencycoordinator muct-shall report the findings as follows:
1) If the assessment indicates that evacuation of local areasmay be advisable, the emergency coordinator muctshal~immediately notify appropriate local authorities. Theemergency coordinator must be available to help appropriateofficials decide whether local areas should be evacuated;and
2) The emergency coordinator muctshall immediately notifyeither the government official designated as the on—scenecoordinator for that geographical area7~ (in the applicableregional contingency plan under 40 CFR Part -l5-lO~,QQ).,, or theNational Response Center (using their 24—hour toll freenumber 800f~424—8802). The report must include:
A) Maine and telephone number of reporter;
B) Name and address of facility;
C) Time and type of incident (e.g., release, fire);
56
13) Name and quantity of material(s) involved, to theextent known;
E) The extent of injuries, if any; and
F) The possible hazards to human health, or theenvironment, outside the facility.
e) During an emergency, the emergency coordinator muatshall take allreasonable measures necessary to ensure that fires, explosions,,and releases do not occur, recur, or spread to other hazardouswaste at the facility. These measures must include, whereapplicable, stopping processes and operations, collecting andcontaining release waste, and removing or isolating containers.
f) If the facility stops operations in response to a fire, explosionor release, the emergency coordinator mustshall monitor for leaks,pressure buildup, gas generation,,, or ruptures in valves, pipes, orother equipment, wherever this is appropriate.
g) Immediately after an emergency, the emergency coordinatormuatshall provide for treating, storing, or disposing of recoveredwaste, contaminated soil or surface water, or any other materialthat results from a release, fire, or explosion at the facility.
BOARD NOTE: Unless the owner or operator can demonstrate, inaccordance with 35 Ill. Adxn. Code 721.103(c) or (d), that therecovered material is not a hazardous waste, the owner or operatorbecomes a generator of hazardous waste and muatshall manage it inaccordance with all applicable requirements of 35 Ill. Adm. Code722, 723, and 724.
h) The emergency coordinator muotahall ensure that, in the affectedarea(s) of the facility:
1) No waste that may be incompatible with the released materialis treated, stored,,, or disposed of until cleanup proceduresare completed; and
2) All emergency equipment listed in the contingency plan iscleaned and fit for its intended use before operations areresumed.
i) The owner or operator muotshall notify the Agency, and appropriatestate and local authorities, that the facility is in compliancewith paragraph (h) before operations are resumed in the affectedarea(s) of the facility.
j) The owner or operator muctshall note in the operating record thetime, date, and details of any incident that requires implementingthe contingency plan. Within 15 days after the incident, theowner or operator muotehali. submit a written report on theincident to the Agency. The report must include:
1) Name, address, and telephone number of the owner or
operator;
2) Name, address, and telephone number of the facility;
3) Date, time, and type of incident (e.g., fire, explosion);
4) Maine and quantity of material(s) involved;
57
5) The extent of injuries, if any;
6) An assessment of actual or potential hazards to human health
or the environment, where this is applicable; and
7) Estimated quantity and disposition of recovered material
that resulted from the incident.
(Source: Amended at _____ Ill. Reg. ________, effective____________________________ )
SUBPARTH: FINANCIAL REQUIREMENTS
Section 724.251 Wording of the Instruments
The Board incorporates by reference 40 CFR 264.151 (198.8~), as amended at 52.Fed. Reg. 4-2~3229960, DcptcmberJune lGQ, 199~. This Section incorporates nolater amendments or editions. The Agency willehall promulgate standardizedforms based on 40 CFR 264.151 with such changes in wording as are necessaryunder Illinois law. Any owner or operator required to establish financialassurance under this Subpart shall do so only upon the standardized formspromulgated by the Agency. The Agency shall reject any financial assurancedocument wh-ic-hthat is not submitted on such standardized forms.
(Source: Amended at _____ Ill. Reg. , effective
Section 724.Appendix A Recordkeeping Instructions
seeThe Board hereby incorporates by reference 40 CFR 264, Appendix I ~1992I,as amended at 59 Fed. Req. 13891 (Mar. 24, 1994~. This incorporation includesno later amendments or editions.
(Source: Amended at _____ Ill. Reg. ________, effective _________
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE C: WASTE DISPOSAL
CHAPTER I: POLLUTION CONTROLBOARDSUBCHAPTERc: HAZARDOUSWASTE OPERATINGREQUIREMENTS
PART 725INTERIM STATUS STANDARDSFOR OWNERSAND OPERATORSOF HAZARDOUS
WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES
SUBPARTA: GENERALPROVISIONSSect ion725.101 Purpose, Scope and Applicability725.104 Imminent Hazard Action
SUBPART 8: GENERALFACILITY STANDARDSSection725.2.10 Applicability725.2.11 USEPA Identification Number725.112 Required Notices725.2.13 General Waste Analysis725.114 Security725.115 General Inspection Requirements725.116 Personnel Training725.117 General Requirements for Ignitable, Reactive or Incompatible
Wastes
58
725.118 Location Standards725.119 Construction Quality Assurance Program
SUBPART C: PREPAREDNESSAND PREVENTIONSection725.130 Applicability725.131 Maintenance and Operation of Facility725.132 Required Equipment725.133 Testing and Maintenance of Equipment725.134 Access to Communications or Alarm System725.135 Required Aisle Space725.137 Arrangements with Local Authorities
SUBPART D: CONTINGENCYPLAN AND EMERGENCYPROCEDURESSection725 • 150 Applicability725.151 Purpose and Implementation of Contingency Plan725.152 Content of Contingency Plan725.153 Copies of Contingency Plan725.154 Amendment of Contingency Plan725.155 Emergency Coordinator725.156 Emergency Procedures
SUBPART E: MANIFEST SYSTEM, RECORDKEEPIMGAND REPORTINGSect ion725.170 Applicability725.171 Use of Manifest System725.172 Manifest Discrepancies725.173 Operating Record725.174 Availability, Retention and Disposition of Records725.175 Annual Report725.176 Unmanifested Waste Report725.177 Additional Reports
SUBPART F: GROUNDWATERMONITORINGSection725. 190 Applicability725.191 Groundwater Monitoring System725.192 Sampling and Analysis725.193 Preparation, Evaluation and Response725.194 Recordkeeping and Reporting
SUBPART G: CLOSUREAND POST-CLOSURESect ion725.210 Applicability725.211 Closure Performance Standard725.212 Closure Plan; Amendment of Plan725.213 Closure; Time Allowed for Closure725.214 Disposal or Decontamination of Equipment, Structures and Soils725.215 Certification of Closure725.216 Survey Plat725.217 Post—closure Care and Use of Property725.218 Post—closure Plan; Amendment of Plan725.219 Post—Closure Notices725.220 Certification of Completion of Post-Closure Care
SUBPART H: FINANCIAL REQUIREMENTSSect ion725.240 Applicability725.242. Definitions of Terms as Used in thia Subpart725.242 Cost Estimate for Closure725.243 Financial Assurance for Closure
59
725.244 Cost Estimate for Post-closure Care725.245 Financial Assurance for Post—closure Monitoring and Maintenance725.246 Use of a Mechanism for Financial Assurance of Both Closure and
Post—closure Care725.247 Liability Requirements725.248 Incapacity of Owners or Operators, Guarantors or Financial
Institutions725.251 Promulgation of Forms (Repealed)
SUBPART I: USE AND MANAGEMENTOF CONTAINERSSection725.270 Applicability725.271 Condition of Containers725.272 Compatibility of Waste with Container725.273- Management of Containers725.274 Inspections725.276 Special Requirements for Ignitable or Reactive Waste725.277 Special Requirements for Incompatible Wastes
SUBPART J: TANK SYSTEMSSect ion725.290 Applicability725.291 Assessment of Existing Tank System’s Integrity725.292 Design and Installation of New Tank Systems or Components725.293 Containment and Detection of Releases725.294 General Operating Requirements725.295 Inspections725.296 Response to leaks or spills and disposition of Tank Systems725.297 Closure and Post-Closure Care725.298 Special Requirements for Ignitable or Reactive Waste725.299 Special Requirements for Incompatible Wastes725.300 Waste Analysis and Trial TestB725.301 Generators of 100 to 1000 kg/mo.
SUBPARTK: SURFACE IMPOUNDMENTSSect ion725.320 Applicability725.321 Design and Operating Requirements725.322 Action Leakage Rate725.323 Response Actions725.324 Containment System725.325 Waste Analysis and Trial Tests725.326 Monitoring and Inspections725.328 Closure and Post-Closure Care725.329 Special Requirements for Ignitable or Reactive Waste725.330 Special Requirements for Incompatible Wastes
SUBPARTL: WASTEPILESSection725.350 Applicability725.352. Protection from Wind725.352 Waste Analysis725 • 353 Containment725.354 Design and Operating Requirements725.355 Action Leakage Rates725.356 Special Requirements for Ignitable or Reactive Waste725.357 Special Requirements for Incompatible Wastes725.358 Closure and Post—Closure Care725.359 Response Actions725.360 Monitoring and Inspection
SUBPARTN: LAND TREATMENT
60
Section725.370 Applicability725.372 General Operating Requirements725.373 Waste Analysis725.376 Food Chain Crops725.378 Unsaturated Zone (Zone of Aeration) Monitoring725.379 Recordkeeping725.380 Closure and Post—closure725.381 Special Requirements for Ignitable or Reactive Waste725.382 Special Requirements for Incompatible Wastes
SUBPART N: LANDFILLSSection725.400 Applicability725.401 Design Requirements725.402 Action Leakage Rate725.403 Response Actions725.404 Monitoring and Inspection725.409 Surveying and Recordkeeping725.410 Closure and Post-Closure725.412 Special Requirements for Ignitable or Reactive Waste725.413 Special Requirements for Incompatible Wastes725.414 Special Requirements for Liquid Wastes725.415 Special Requirements for Containers725.416 Disposal of Small Containers of Hazardous Waste in Overpacked
Drums (Lab Packs)
SUBPART0: INCINERATORSSection725. 440 Applicability725.441 Waste Analysis725.445 General Operating Requirements725.447 Monitoring and Inspection725.451 Closure725.452 Interim Status Incinerators Burning Particular Hazardous Wastes
SUBPARTP: THERMALTREATMENTSection725.470 Other Thermal Treatment725.473 General Operating Requirements725.475 Waste Analysis725.477 Monitoring and Inspections725.481 Closure725.482 Open Burning; Waste Explosives725.483 Interim Status Thermal Treatment Devices Burning Particular
Hazardous Waste
SUBPART Q: CHEMICAL, PHYSICAL AND BIOLOGICAL TREATMENTSection725.500 Applicability725.501 General Operating Requirements725.502 Waste Analysis and Trial Tests725.503 Inspections725.504 Closure725.505 Special Requirements for Ignitable or Reactive Waste725.506 Special Requirements for Incompatible Wastes
SUBPART R: UNDERGROUNDINJECTIONSection725.530 Applicability
SUBPART W: DRIP PADS
61
Sect ion725 • 540 Applicability725.541 Assessment of existing drip pad integrity725.542 Design and installation of new drip pads725.543 Design and operating requirements725. 544 Inspections725.545 Closure
SUBPARTAR: AIR EMISSION STANDARDSFOR PROCESSVENTSSect ion725. 930 Applicability725.931 Definitions725.932 Standards: Process Vents725.933 Standards: Closed-vent Systems and Control Devices725.934 Test methods and procedures725.935 Recordkeeping Requirements
SUBPART BB: AIR EMISSION STANDARDSFOR EQUIPMENTLEAKSSection725. 950 Applicability725.951 Definitions725.952 Standards: Pumps in Light Liquid Service725.953 Standards: Compressors725.954 Standards: Pressure Relief Devices in Gas/Vapor Service725.955 Standards: Sampling Connecting Systems725.956 Standards: Open-ended Valves or Lines725.957 Standards: Valves in Gas/Vapor or Light Liquid Service725.958 Standards: Pumps, Valves, Pressure Relief Devices, Flanges and
Other Connectors725.959 Standards: Delay of Repair725.960 Standards: Closed-vent Systems and Control Devices725.961 Percent Leakage Alternative for Valves725.962 Skip Period Alternative for Valves725.963 Test Methods and Procedures725.964 Recordkeeping Requirements
SUBPART DD: CONTAINMENTBUILDINGS
Section725.1100 Applicability725.12.01 Design and operating standards725.1102 Closure and post—closure care
725.Appendix A Recordkeeping Instructions725.Appendix B EPA Report Form and Instructions (Repealed)725.Appendix C EPA Interim Primary Drinking Water Standards725.Appendix D Teats for Significance725.Appendix E Examples of Potentially Incompatible Waste
AUTHORITY: Implementing Section 22.4 and authorized by Section 27 of theEnvironmental Protection Act (Ill.- Roy. Stat. 1991, oh. 111~, parc. 1022.4 and1027 (415 ILCS 5/22.4 and 273)-.
SOURCE: Adopted in R81—22, 43 PCB 427, at 5 11.1. Reg. 9781, effective asnoted in 35 Ill. Adm. Code 700.106; amended and codified in R81-22, 45 PCB317, at 6 Ill. Reg. 4828, effective as noted in 35 Iii. Adm. Code 700.106;amended in R82—2.8, Si. PCS 831, at 7 Ill. Reg. 2618, effective February 22,1983; amended in R82—19, 53 PCB 131, at 7 Il].. Reg. 14034, effective October12, 1983; amended in R84—9, at 9 Ill. Reg. 11869, effective July 24, 1985;amended in R85—22 at 10 Ill. Reg. 1085, effective January 2, 1986; amended inR86—1 at 10 Ill. Reg. 14069, effective August 12, 1986; amended in R86—28 at11 Ill. Reg. 6044, effective March 24, 1987; amended in R86—46 at 11 Ill. Reg.
62
13489, effective August 4, 1987; amended in R87—5 at 11 Ill. Reg. 19338,effective November 10, 1987; amended in R87-26 at 12 Iii. Reg. 2485, effectiveJanuary 15, 1988; amended in R87—39 at 12 Ill. Reg. 13027, effective July 29,1988; amended in R88—16 at 13 Ill. Reg. 437, effective December 28, 1988;amended in R89—1 at 13 Ill. Reg. 18354, effective November 13, 1989; amendedin R90—2 at 14 Ill. Reg. 14447, effective August 22, 1990; amended in R90—10at 14 Ill. Reg. 16498, effective September 25, 1990; amended in R90—11 at 15Ill. Reg. 9398, effective June 17, 1991; amended in R91-l at 15 Ill. Reg.14534, effective October 1, 1991; amended in R91—l3 at 2.6 Ill. Reg. 9578,effective June 9, 1992; amended in R92—2. at 16 Ill. Reg. 17672, effectiveNovember 6, 1992; amended in R92—lO at 17 Ill. Reg. 5682., effective March 26,1993; amended in R93—4 at 2.7 Ill. Reg. 20620, effective November 22, 1993;amended in R93—16 at 18 Ill. Reg. 6771, effective April 26, 1994; amended inR94-7 at 18 Ill. Reg. 122.90, effective July 29, 1994; amended in R94—17 at
Ill. Rep. , effective
SUBPART D: CONTINGENCYPLAN AND EMERGENCYPROCEDURES
Section 725.152 Content of Contingency Plan
a) The contingency plan must describe the actions facility personnelmust take to comply with Sections 725.151 and 725.156 in responseto fires, explosions,~ or any unplanned sudden or non—suddenrelease of hazardous waste or hazardous waste constituents to air,soi1~ or surface water at the facility.
b) If the owner or operator has already prepared a Spill PreventionTControl and Countermeasures (SPCC) Plan in accordance with 40 CFRPart 112 or 1510300, or some other emergency or contingency plan,he~j~need~ only amend that plan to incorporate hazardous wastemanagement provisions that are sufficient to comply with therequirements of this Part.
c) The plan must describe arrangements agreed to by local policedepartment, fire departments, hospitals, contractors~~ and stateand local emergency response teams to coordinate emergencyservices, pursuant to Section 725.137.
d) The plan must list names, addresses~ and phone numbers (office andhome) of all persons qualified to act as emergency coordinator(see Section 725.2.55)~. and this list must be kept up to date.Where more than one person is listed one must be named as primaryemergency coordinator and others must be listed in the order inwhich they will assume responsibility as alternates.
e) The plan must include a list of all emergency equipment at thefacility (such as fire extinguishing systems, spill controlequipment, communications and alarm systems (internal andexterna1)~ and decontamination equipment) where this equipment isrequired. This list must be kept up to date. In addition, theplan must include the location and a physical description of eachitem on the list and a brief outline of its capabilities.
f) The plan must include an evacuation plan for facility personnelwhere there is a possibility that evacuation could be necessary.This plan must describe signal(s) to be used to begin evacuation,evacuation routes and alternate evacuation routes (in cases wherethe primary routes could be blocked by releases of hazardous wasteor fires).
(Source: Amended at Ill. Reg. _________, effective
63
Section 725.156 Emergency Procedures
a) Whenever there is an imminent or actual emergency situation, theemergency coordinator (or his designee when the emergencycoordinator is on call) muctshall immediately:
1) Activate internal facility alarms or communication systems,where applicable, to notify all facility personnel; and
2) Notify appropriate state or local agencies with designatedresponse roles if their help is needed.
b) Whenever there is a release, fired. or explosion, the emergencycoordinator muotshall immediately identify the character, exactsource, amount~ and a real extent of any released materials. Heor she may do this by observation or review of facility records ormanifests and, if necessary, by chemical analysis.
c) Concurrently, the emergency coordinator muctahal]. assess possiblehazards to human health or the environment that may result fromthe release, fire~ or explosion. This assessment must considerboth direct and indirect effects of the release, fire,., orexplosion (e.g., the effects of any toxic, irritating~ orasphyxiating gases that are generated,,, or the effects of anyhazardous surface water runoffs from water or chemical agents usedto control fire and heat—induced explosionB).
d) If the emergency coordinator determines that the facility has hada release, fire,, or explosion whiohthat could threaten humanhealth or the environment outside the facility, he or shemt~wtshall report his findings as follows:
1) If his assessment indicates that evacuation of local areasmay be advisable, he or she muotehall immediately notifyappropriate local authorities. He or she must be availableto help appropriate officials decide whether local areasshould be evacuated; and
2) He or she mu~tshall immediately notify either the governmentofficial designated as the on—scene coordinator for thatgeographical area (in the applicable regional contingencyplan under 40 CFR Part 1-5101Q2),, or the National ResponseCenter (using their 24—hour toll free number 8OO~~424—8802).The report must include:
A) Name and telephone number of reporter;
B) Name and address of facility;
C) Time and type of incident (e.g., release, fire);
D) Name and quantity of material(s) involved, to the
extent known;
E) The extent of injuries, if any; and
F) The possible hazards to human health or theenvironment outside the facility.
e) During an emergency the emergency coordinator muotshall take all
64
reasonable measures necessary to ensure that fires, explosions,,and releases do not occur, recur, or spread to other hazardouswaste at the facility. These measures must include, whereapplicable, stopping processes and operations, collecting andcontaining released waste, and removing or isolating containers.
f) If the facility stops operations in response to a fire, explosionor release, the emergency coordinator muotshall monitor for leaks,pressure buildup, gas generation, or ruptures in valves, pipes, orother equipment, wherever this is appropriate.
g) Immediately after an emergency, the emergency coordinatormuotshall provide for treating, storing, or disposing of recoveredwaste, contaminated soil, or surface water, or any other materialthat results from a release, fire, or explosion at the facility.
Comment: Unless the owner or operator can demonstrate, inaccordance with Section 721.103(c) or (d) that the recoveredmaterial is not a hazardous waste, the owner or operator becomes agenerator of hazardous waste and muotahall manage it in accordancewith all applicable requirements of Parts 722, 723,, and 725.
h) The emergency coordinator muctshall ensure that, in the affectedarea(s) of the facility:
1) No waste that may be incompatible with the released materialis treated, stored, or disposed of until cleanup proceduresare completed; and
2) All emergency equipment listed in the contingency plan iscleaned and fit for its intended use before operations areresumed.
i) The owner or operator muotshall notify the Director and otherappropriate state and local authorities that the facility is incompliance with paragraph (h) of this section before operationsare resumed in the affected area(s) of the facility.
j) The owner or operator muotehall note in the operating record thetime, date, and details of any incident that requires implementingthe contingency plan. Within 15 days after the incident, ~iej~,muotahall submit a written report on the incident to the Director.The report must include:
1) Name, address, and telephone number of the owner or
operator;
2) Name, address, and telephone number of the facility;
3) Date, time, and type of incident (e.g., fire, explosion);
4) Name and quantity of material(s) involved;
5) The extent of injuries, if any;
6) An assessment of actual or potential hazards to human health
or the environment, where this is applicable; and
7) Estimated quantity and disposition of recovered material
that resulted from the incident.
(Source: Amended at Ill. Reg. ________, effective
65
Section 725.Appendix A Recordkeeping Instruction~
SeeThe Board hereby incorporates by reference 40 CFR 265, Appendix I to 40 CFRPart 265(1992~. as amended at 59 Fed. Req. 13892 (Mar. 24 1994~. Thisincorporation includes no later amendments or editions.
(Source: Amended at Ill. Reg. , effective _________
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE C: WASTE DISPOSAL
CHAPTERI: POLLUTION CONTROLBOARDSUBCHAPTER c: HAZARDOUSWASTE OPERATING REQUIREMENTS
PART 728LAND DISPOSAL RESTRICTIONS
SUBPARTA: GENERALSection728.101 Purpose, Scope and Applicability728.102 Definitions728.103 Dilution Prohibited as a Substitute for Treatment728.104 Treatment Surface Impoundment Exemption728.105 Procedures for case—by—case Extensions to an Effective Date728.106 Petitions to Allow Land Disposal of a Waste Prohibited under
Subpart C728.107 WaBte Analysis and Recordkeeping728.108 Landfill and Surface Impoundment Disposal Restrictions (Repealed)728.109 Special Rules for Characteristic Wastes
SUBPART B: SCHEDULEFOR LAND DISPOSAL PROHIBITIONAND ESTABLISHMENT OF TREATMENTSTANDARDS
Section728.2.10 First Third728.12.1 Second Third728.112 Third Third728.113 Newly Listed Wastes728.114 Surface Impoundment exemptions
SUBPARTC: PROHIBITION ON LAND DISPOSALSection728.130 Waste Specific Prohibitions —— Solvent Wastes728.131 Waste Specific Prohibitions -— Dioxin—Containing Wastes728.132 Waste Specific Prohibitions —— California List Wastes728.133 Waste Specific Prohibitions -— First Third Wastes728.134 Waste Specific Prohibitions —— Second Third Wastes728.135 Waste Specific Prohibitions -— Third Third Wastes728.136 Waste Specific Prohibitions —* Newly Listed Wastes728.137 Waste Specific Prohibitions —— Ignitable and Corrosive
Characteristic Wastes Whose Treatment Standards Were Vacated728.139 Statutory Prohibitions
SUBPARTD: TREATMENTSTANDARDSSection728.140 Applicability of Treatment Standards728.141 Treatment Standards Expressed as Concentrations in Waste Extract728.142 Treatment Standards Expressed as Specified Technologies728.143 Treatment Standards expressed as Waste Concentrations728.144 Adjustment of Treatment Standard
66
Treatment Standards for Hazardous DebrisAlternative Treatment Standards Based on HTMR
SUBPART E: PROHIBITIONS ON STORAGESection728.150 Prohibitions on Storage of Restricted Wastes
728.Appendix A728.Appendix B
728.Appendix C728.Appendix D728.Appendix E728.Appenclix F728.Appendix 0728.Appendix H728.Appendix I
728.Table A728.Table B728.Table C
728..Table D728.Table E728.Table F728.Table 0728.Table H
Toxicity Characteristic Leaching Procedure (TCLP)Treatment Standards (As concentrations in the TreatmentResidual Extract)List of Halogenated Organic CompoundsOrganometallic Lab PacksOrganic Lab PacksTechnologies to Achieve Deactivation of CharacteristicsFederal Effective DatesNational Capacity LDR Variances for UIC WastesEP Toxicity Test Method and Structural Integrity Test
Constituent Concentrations in Waste Extract (CCWE)Constituent Concentrations in Wastes (CCW)Technology Codes and Description of Technology—BasedStandardsTechnology—BasedStandardsby RCRA Waste CodeStandards for Radioactive Mixed WasteAlternative Treatment Standards for Hazardous DebrisAlternative Treatment Standards Based on HMTRWastes Excluded from CCWTreatment Standards
AUTHORITY: Implementing Section 22.4 and authorized by Section 27 of theEnvironmental Protection Act (Ill. Rev. Stat. 1991, ch. 111½, pars. 1022.4 and1027 (415 ILCS 5/22.4 and 5/27]).
SOURCE: Adopted in R87—5 at 11 Ill. Reg. 19354, effective November 12, 1987;amended in R87—39 at 12 Ill. Reg. 13046, effective July 29, 1988; amended inR89—1 at 13 Ill. Reg. 18403, effective November 13, 1989; amended in R89—9 at14 Ill. Reg. 6232, effective April 16, 1990; amended in R90—2 at 14 Ill. Reg.14470, effective August 22, 1990; amended in R90—10 at 14 Ill. Reg. 16508,effective September 25, 1990; amended in R90—11 at 15 Ill. Reg. 9462,effective June 17, 1991; amended in R92—2.0 at 2.7 Ill. Reg. 5727, effectiveMarch 26, 1993; amended in R93—4 at 17 Ill. Reg. 20692, effective November 22,1993; amended in R93—2.6 at 18 Ill. Reg. 6799, effective April 26, 1994;amended in R94—7 at 18 Ill. Reg. 12203, effective July 29, 1994; amended inR94—17 at Ill. Req. , effective
SUBPART D: TREATMENTSTANDARDS
Section 728.142 Treatment Standards Expressed as Specified Technologies
a) The following wastes in subsections (ay(1) and J~(2) below andSections 728.Table D and 728.Table B must be treated using thetechnology or technologies specified in subsections (a)(1) andJA.l(2) below and Section 728.Table C.
1) Liquid hazardous wastes containing PCBs at concentrationsgreater than or equal to 50 ppm but less than 500 ppm mustbe incinerated in accordance with the technical requirementsa#~ 40 CFR 761.70, incorporated by reference in 35 Ill.Adm. Code 720.111, or burned in high efficiency boilers inaccordance with the technical requirements of 40 CFR 761.60.Liquid hazardous wastes containing PCBs at concentrationsgreater than or equal to 500 ppm must be incinerated in
728.145728. 146
67
accordance with the technical requirements of 40 CFR 761.70.Thermal treatment in accordance with this Section must be incompliance with applicable regulations in 35 Ill. Adm. Code724, 725, and 726.
2) Nonliquid hazardous wastes containing halogenated organiccompounds (HOCs) in total conc~ntrationa greater than orequal to 1000 mg/kg and liquid HOC—containing wastes thatare prohibited under Section 728.132(e)(1) must beincinerated in accordance with the requirements of 35 Ill.Adm. Code 724.Subpart 0 or 35 Ill. Adm. Code 725.Subpart 0.These treatment standards do not apply where the waste issubject to a Cubpart C-of this Part treatment standardcodified in Subpart C of this Part for a specific HOC (suchas a hazardous waste chlorinated solvent for which atreatment standard is established under Section 728.141(a)).
3) A mixture consisting of wastewater, the discharge of whichis subject to regulation under 35 Ill. Adm. Code 309 or 310,and de minimis losses of materials from manufacturingoperations in which these materials are used as rawmaterials or are produced as products in the manufacturingprocess, and that meets the criteria of the DOOl ignitableliquids containing greater than 10% total organicconstituents (TOC) subcategory, is subject to the DEACTtreatment standard described in Table C. For purposes ofthis subsection, “de minimis losses” include:
A) Those from normal material handling operations (e.g.,spills from the unloading or transfer of materialsfrom bins or other containers, ~.leaks from pipes,valves, or other devices used to transfer materials);
B) Minor leaks from process equipment, storage tanks, or
containers;
C) Leaks from well—maintained pump packings and seals;
D) Sample purgings; and
E) Relief device discharges.
b) Any person may submit an application to the Agency demonstratingthat an alternative treatment method can achieve a level ofperformance equivalent to that achievable by methods specified insubsections (a) above and (c) and (d) below for wastes orspecififed in Section 728.Table F for hazardous debris. Theapplicant shall submit information demonstrating that theapplicant’s treatment method is in compliance with federal andstate requirements, including this Part, 35 Ill. Adm. Code 709,724, 725, 726, and 729 and Sections 22.6 and 39(h) of theEnvironmental Protection Act (Ill. Roy. Stat. 1987, oh. 1l1~,parc. 1022.6 and 1039(h) (415 ILCS 5/22.6 and S’/’39(h))-~, and thatj~is protective of human health or the environment. On the basisof such information and any other available information, theAgency shall approve the use of the alternative treatment methodif the Agency finds that the alternative treatment method providesa measure of performance equivalent to that achieved by methodsspecified in subsections (a) above and (c) and (d) below and inSection 728.Table F, for hazardous debris. Any approval must bestated in writing and may contain such provisions and conditionsas the Agency determines to be appropriate. The person to whom
68
such approval is issued shall comply with all limitationscontained in such determination.
c) As an alternative to the otherwise applicable treatment standardsof Subpart D of this Part, lab packs are eligible for landdisposal provided the following requirements are met:
1) The lab packs comply with the applicable provisions of 35Ill. Adm. Code 724.416 and 725.416;
BOARDNOTE: 35 Ill. Adm. Code 729.301 and 729.312 includeadditional restrictions on the use of lab packs.
2) All hazardous wastes contained in such lab packs arespecified in Section 728.Appendix D or Section 728.Appendix
3) The lab packs are incinerated in accordance with therequirements of 35 Ill. Mm. Code 724.Subpart 0 or 35 Ill.Acim. Code 725.Subpart 0; and
4) Any incinerator residues from lab packs containing D004,D005, D006, P007, D008, DOlO, and DOll are treated incompliance with the applicable treatment standards specifiedfor such wastes in Subpart P.
d) Radioactive hazardous mixed wastes with treatment standardsspecified in Section 728.Table B are not subject to any treatmentstandards specified in Section 728.141, Cection 728.143, orGcctipn 728.Table D. Radioactive hazardous mixed wastes notsubject to treatment standards in Section 728 .Table E remainsubject to all applicable treatment standards specified inSection~ 728.141, Cection 728.143, and Ccction 728.Table P.Hazardous debris containing radioactive waste is not subject tothe treatment standards specified in Section 728.Table F but issubject to the treatment standards specified in Section 728.145.
(Source: Amended at Ill. Reg. _________, effective
Section 728.Table D Technology-Based Standards by RCRA Waste Code
Technology TechnologyCode, Code, Non—
Waste Waste— waste— Waste Descriptions orCodes See Also CAS No. waters waters Treatment Subcategory
DOOl Tables A NA DEACT, and DEACT, and All descriptions based& B meet P039; meet P039; on 35 Ill. Adm. Code
or PSUBS; or FSUBS; 721.121, except for theRORGS; or RORGS; or Section 721.121(a) (1)INCIN INCIN High TOC subcategory,
managed in non-CWA/non—CWA-equivalent/ non-ClassI SDWAsystems
69
DOOl NA NA DEACT DEACT All descriptions basedon 35 Ill. Adxn. Code721.121, except for theSection 261.121(a)(1)High TOC subcategory,managed in CWA, CWA-equivalent, or Class ISDWAsystems
POOl NA NA NA FSUBS; Al]. descriptions basedRORGS; or on 35 Ill. Adm. CodeINCIN 721.121(a) (1)—High TOC
Ignitable Liquids Sub—category——Greater thanor equal to 10% totalorganic carbon
P002 Tables A NA DEACT and DEACT and Acid, alkaline, and& B meet P039 meet F039 other subcategory based
on 35 Ill. Adm. Code721.122 managed in non-CWA/non-CWA-equ ivalent/non-Class I SDWAsystems
D002 NA NA DEACT DEACT Acid, alkaline, andother subcategory basedon 35 Ill. Adm. Code721.122 managed in CWA,CWA-equivalent, or ClassI SDWAsystems
P003 NA NA DEACT (but DEACT (but Reactive sulf ides basednot in- not in— on 35 Ill. Adm. Codecluding cluding 721.123(a) (5)dilution dilutionas a sub— as a sub-stitute stitutefor ade— for ade-quate quatetreatment) treatment)
P003 NA NA DEACT DEACT Explosives based on 35Ill. Adm. Code 721.2.23(a)(6), j~J.(7), andIa.)~ (8)
P003 NA NA NA DEACT Water reactives based on35 Ill. Adm. Code72l.123(a)(2), .Lal(3),,and ~j.(4)
D003 NA NA DEACT DEACT Other reactives based on35 Ill. Adm. Code721.123(a) (1)
P006 NA 7440-43—9 NA RTHERM Cadmium—containing bat-teries
70
D008 NA 7439—92—1 NA RLEAD Lead acid batteries(Note: This standardonly applies to leadacid batteries that areidentified as RCRAhazardous wastes andthat are not excludedelsewhere fromregulation under theland disposal re-strictions of this Partor exempted under otherregulations (see 35 Ill.Adm. Code 726.180).)
P009 Tables A 7439—97—6 NA IMERC; or Mercury: (High Mercury& B RMERC Subcategory--greater
than or equal to 260mg/kg total Mercury-—contains mercury and or-ganics (and are notincinerator residues))
P009 Tables A 7439—97—6 NA RMERC Mercury: (High Mercury& B Subcategory--greater
than or equal to 260mg/kg total Mercury-—inorganics (includingincinerator residues ancresidues from RI4ERC))
P012 Table B 72-20—8 BIODG; or NA EadrinINCIN
P013 Table B 58-89—9 CARBN; or NA LindaneINCIN
P014 Table B 72-43—S WETOX; or NA NethoxychlorINCIN
P015 Table B 8001—35—1 BIODG; or NA ToxapheneINCIN
P016 Table B 94—75—7 CHOXD; NA 2,4—PBIODG; orINCIN
D017 Table B 93-72—1 CHOXD; or NA 2,4,5—TPINCIN
F005 Tables A 79-46—9 (WETOX or INCIN 2—Nitropropane& B CHOXD) fb
CARBN; orINCIN
P005 Tables A 110—80—5 BIODG; or INCIN 2—Ethoxyethanol
& B INCIN
F024 Tables A NA INCIN INCIN
71
K025 NA NA LLEXT fb INCIN Distillation bottomsSSTRIP fb from the production ofCARBN; or nitrobenzene by theINCIN nitration of benzene
1(026 NA NA INCIN INCIN Stripping still tailsfrom the production ofmethyl ethyl pyridines
1(027 NA NA CARBN; or FSUBS; or Centrifuge andINCIN INCIN distillation residues
from toluene di—isocyanate production
1(039 NA NA CARBN; or FSUBS; or Filter cake from theINCIN INCIN filtration of diethyl-
phoaphorodithioc acid inthe production of phor—ate
1(044 NA NA DEACT DEACT Wastewater treatmentsludges from the manu-facturing and processingof explosives
1(045 NA NA DEACT DEACT Spent carbon from thetreatment of wastewatercontaining explosives
1(047 NA NA DEACT DEACT Pink/red water from TNToperations
1(069 Tables A NA NA RLEAD Emission control dust/& B sludge from secondary
lead smelting: Non-Calcium Sulfate Sub-category
1(106 Tables A NA NA RNERC Wastewater treatment& B sludge from the mercury
cell process in chlorineproduction: (HighMercury Subcategory-greater than or equal to260 mg/kg total mercury)
1(107 NA NA INCIN; or INCIN. Column bottoms fromCHOXDfb, product separation fromCARBN; or the production of 1,1—BIODG Lb dimethylhydrazine (UDMR)CARBN from carboxylic acid
hydrazides
1(108 NA NA INCIN; or INCIN. Condensed columnCH0XD fb, overheads from productCARBN; or separation and condensedBIOPG Lb reactor vent gases fromCARBN the production of 1,1—
dimethylhydrazine (UDMH)from carboxylic acidhydrazides
72
1(109 NA NA INCIN; or INCIN. Spent filter cartridgesCHOXD fb, from productCARBN; or purification from theBIODG fb production of 1,1—CARBN dimethylhydrazine (UDMH)
from carboxylic acidhydrazides
K110 NA NA INCIN; or INCIN. Condensed columnCHOXDfb, overheads fromCARBN; or intermediate separationBIODG Lb from the production ofCARBN 1, 1-dimethylhydrazine
(UDMH) from carboxylicacid hydrazides
1(112 NA NA INCIN; or INCIN. Reaction by-productCHOXDfb, water from the dryingCARBN; or column in the productionBIODG fb of toluenediamine viaCARBN hydrogenation of
dinitroto luene
1(113 NA NA CARBN; or FSUBS; or Condensed liquid lightINCIN INCIN ends from the
purification oftoluenediamine in theproduction oftoluenediaxnine viahydrogenation of di-nitrotoluene
1(114 NA NA CARBN; or FSUBS; or Vicinals from theINCIN INCIN purification of tol-
uenediamine in theproduction of toluenedi-amine via hydrogenationof dinitrotoluene
1(115 NA NA CARBN; or FSUBS; or Heavy ends from theINCIN INCIN purification of
toluenediamine in theproduction of tol-uenediamine viahydrogenation of di-nitroto luene
1(2.16 NA NA CARBN; or FSUBS; or Organic condensate fromINCIN INCIN the solvent recovery
column in the productionof toluene diisocyanatevia phosgenation oftoluenediamine
K123 NA NA INCIN; or INCIN. Process wastewaterCHOXD Lb (including supernates,(BIODG or filtrates, andCARBN) washwaters) from the
production ofethylenebis-dithiocarbamic acid andits salts
73
1(124 NA NA INCIN; or INCIN. Reactor vent scrubberCHOXDfb water from the(BIODG or production ofCARBN) ethylenebisdi-
thiocarbamic acid andits salts
1(125 NA NA INCIN; or INCIN. Filtration, evaporation,CHOXDLb and centrifugation(BIODG or solids from theCARBN) production of
ethylenebisdi—thiocarbamic acid andits salts
1(126 NA NA INCIN; or INCIN. Baghouse dust and floorCHOXDfb sweepings in milling and(BIODG or packaging operationsCARBN) from the production or
formulation of ethylenebisdithiocarbaniic acidand its salts
P001 NA 81—81—2 (WETOX or FSUBS; or Warfarin (>0.3%)CHOXD) fb INCINCARBN; orINCIN
P002 NA 591—08—2 (WETOX or INCIN 1—Acetyl-2-thioureaCHOXD) lbCARBN; orINCIN
P003 NA 107-02—8 NA FSUBS; or AcroleinINCIN
P005 NA 107—18—6 (WETOX or FSUBS; or Allyl alcoholCHOXD) Lb INCINCARBN; orINCIN
P006 NA 20859-73-8 CHOXD; CHOXD; Aluminum phoephideCHRED; or CHRED; orINCIN INCIN
P007 NA 2763—96-4 (WETOX or INCIN 5—Azninoethyl 3-CHOXD) Lb isoxazololCARBN; orINC IN
P008 NA 504-24-5 (WETOX or INCIN 4—ArninopyridineCHOXD) LbCARBN; orINCIN
P009 NA 131-74—8 CHOXD; FSUBS; CH— Ammonium picrateCHRED; OXD;CAREN; CHRED; orBIODO; or INCININC IN
74
P014 NA 108-95-5 (WETOX or INCIN Thiophenol (BenzeneCHOXD) fb thiol)CARBN; orINCIN
P015 NA 7440-41—7 RMETL or RMETL; or Beryllium duotpowderRTHRM RTHRM
P016 NA 542-88-1 (WETOX or INCIN Bis(chloromethyl)etherCHOXD) lbCAREN; orINCIN
P017 NA 598-31-2 (WETOX or INCIN BromoacetoneCHOXD) LbCAREN; orINCIN
P018 NA 357-57-3 (WETOX or INCIN BrucineCHOXD) LbCARBN; orINC IN
P022 Table B 75—15—0 NA INCIN Carbon disulfide
P023 NA 107-20-0 (WETOX or INCIN ChloroacetaldehydeCHOXD) LbCARBN; orINCIN
P026 NA 5344-82—1 (WETOX or INCIN 1—(o—Chlorophenyl)thio-CHOXD) fb ureaCARBN; orINCIN
P027 NA 542—76—7 (WETOX or INCIN 3—ChloropropionitrileCHOXD) lbCARBN; orINCIN
P028 NA 100-44—7 (WETOX or INCIN Benzyl chlorideCHOXD) lbCARBN; orINCIN
P031 NA 460-19-5 CHOXD; CHOXD; CyanogenWETOX; or WETOX; orINCIN INCIN
P033 NA 506-77—4 CHOXD; CHOXD; Cyanogen chlorideWETOX; or WETOX; orINCIN INCIN
P034 NA 131—89—5 (WETOX or INCIN 2—Cyclohexyl—4,6-di—CHOXD) lb nitrophenolCARBN; orINCIN
P040 NA 297—97—2 CARBN; or FSUBS; or 0,0-Diethyl 0—pyrazinylINCIN INCIN phoaphorothioate
75
P041 NA 311-45-5 CARBN; or FSUBS; or Diethyl—p-nitrophenylINCIN INCIN phosphate
P042 NA 51-43-4 (WETOX or INCIN EpinephrineCHOXD) lbCARBN; orINCIN
P043 NA 55-91-4 CARBN; or FSUBS; or Diisopropylfluorophos-INCIN INCIN phate (DFP)
P044 NA 60-52.-S CARBN; or FSUBS; or DimethoateINCIN INCIN
P045 NA 39196-18—4 (WETOX or INCIN ThiofanoxCHOXD) LbCARBN; orINCIN
P046 NA 122—09—8 (WETOX or INCIN alpha,alpha—Pimethyl-CHOXP) Lb phenethylamineCARBN; orINCIN
P047 NA 534—52—1 (WETOX or INCIN 4,6—Dinitro—o—cresolCHOXD) lb saltsCAREN; orINCIN
P049 NA 541—53—7 (WETOX or INCIN 2,4-DithiobiuretCHOXD) lbCARBN; orINCIN
P054 NA 2.51—56—4 (WETOX or INCIN AziridineCHOXD) fbCARBN; orINCIN
P056 Table B 778241—4 NA ADGAS Lb FluorineNEUTR
P057 NA 640—19-7 (WETOX or INCIN FluoroacetamideCHOXD) fbCARBN; orINC IN
P058 NA 62—74—8 (WETOX or INCIN Fluoroacetic acid,CHOXD) Lb sodium saltCARBN; orINCIN
P062 NA 757-58-4 CARBN; or FSUBS or HexaethyltetraphosphateINCIN INCIN
P064 NA 624-83-9 (WETOX or INCIN Isocyanic acid, ethylCHOXD) Lb esterCARBN; orINCIN
76
P065 Tables A 628-86—4 NA RMERC Mercury fulminate:& B (High Mercury Sub-
category——greater thanor equal to 260 mg/kgtotal Mercury-—eitherincinerator residues orresidues from R14ERC)
P065 Tables A 628-86—4 NA II4ERC Mercury fulminate: (All& B nonwastewaters that are
not incinerator residuesor are not residues fromRNERC; regardless ofMercury Content)
P066 NA 16752-77-5 (WETOX or INCIN MethomylCHOXD) LbCABEN; orINCIN
P067 NA 75-55-8 (WETOX or INCIN 2—NethylaziridineCHOXD) LbCAREN; orINCIN
P068 NA 60-34-4 CHOXD; CM— FSUBS; CM- Methyl hydrazineRED; OXD;CARBN; CHRED; ORBIODG; or INCININCIN
P069 NA 75—86-5 (WETOX or INCIN MethyllactonitrileCHOXD) LbCARBN; orINCIN
P070 NA 116—06-3 (WETOX or INCIN AldicarbCHOXD) LbCAREN; orINCIN
P072 NA 86—88—4 (WETOX or INCIN 1—Naphthyl-2—thioureaCHOXD) fbCARBN; orINC IN
P075 NA 54—11—5 (WETOX or INCIN Nicotine and saltsCHOXD) fbCAREN; orINC IN
P076 NA 10102—43-9 ADGAS ADGAS Nitric oxide
P078 NA 2.0102—44-0 ADGAS ADGAS Nitrogen dioxide
P081 NA 55—63—0 CHOXD; CM— FSUBS; CM— NitroglycerinRED; OXD;CARBN; CHRED; orBIODG; or INCININCIN
P082 Table B 62-75—9 NA INCIN N—Nitrosodimethylamine
77
P084 NA 4549—40-0 (WETOX or INCIN N—Nitrosomethylvinyl-CHOXD) fb amineCARBN; orINCIN
P085 NA 152—16—9 CARBN; or FSUBS; or Octamethylpyrophosphor—INCIN INCIN amide
P087 NA 20816-12—0 BMETL; or RMETL; or Osmium tetroxideRTHEM RTHRM
P088 NA 145—73—3 (WETOX or FSUBS; or EndothallCHOXD) Lb INCINCAREN; orINCIN
P092 Tables A 62-38—4 NA RMERC Phenyl mercury acetate:& B (High Mercury Sub—
category——greater thanor equal to 260 mg/kgtotal Mercury—-eitherincinerator residues orresidues from RNERC)
P092 Tables A 62—38—4 NA IMERC; or Phenyl mercury acetate:& B RMERC (All nonwastewaters that
are not incineratorresidues and are notresidues from RMERC:regardless of MercuryContent)
P093 NA 103-85-5 (WETOX or INCIN PhenylthioureaCHOXD) lbCARBN; orINCIN
P095 NA 75—44-5 (WETOX or INCIN PhosgeneCHOXD) lbCARBN; orINCIN
P096 NA 7803—51—2 CHOXD; CM— CHOXD; CM— PhosphineRED; or RED; orINCIN INCIN
P102 NA 107—19—7 (WETOX or FSUBS; or Propargyl alcoholCHOXD) fb INCINCARBN; orINCIN
P105 NA 26628—22-8 CHOXD; CM— FSUBS; CM— Sodium azideRED; CARBN OX!);BIODG; or CHRED; orINCIN INCIN
P108 NA 57—24—9A (WETOX or INCIN Strychnine and saltsCHOXD) LbCARBN; orINCIN
78
P109 NA 3689-24-5 CARBN; or FSUBS; or Tetraethyldithiopyro—INCIN INCIN phosphate
P112 NA 509-14-8 CMOXD; CM- PSUBS; CM- TetranitromethaneRED; OXD;CARBN; CHRED; orBIODG; or INCININCIN
P113 Table B 1314—32—5 NA RTHRM; or Thallic oxideSTABL
P12.5 Table B 7446-18—6 NA RTHRN; or Thallium (I) sulfateSTABL
P116 NA 79-19—6 (WETOX or INCIN ThiosemicarbazideCHOXD) fbCARBN; orINCIN
P118 NA 75-70—7 (WETOX or INCIN TrichioromethanethiolCHOXD) lbCARBN; orINCIN
P2.19 Table B 7803—55—6 NA STABL Ainmonium vanadate
P120 Table B 1314-62-1 NA STABL Vanadium pentoxide
P122 NA 1314-84-7 CHOX!); CM— CHOXD; CM- Zinc Phosphide (~10%)RED; or RED; orINCIN INCIN
13001 NA 75-07-0 (WETOX or INCIN AcetaldehydeCHOXD) LbCARBN; orINCIN
13003 Table B 75-05—8 NA INCIN Acetonitrile
13006 NA 75—36—5 (WETOX or INCIN Acetyl chlorideCHOXD) fbCARBN; orINCIN
U007 NA 79-06—1 (WETOX or INCIN AcrylamideCHOXD) LbCARBN; orINCIN
U008 NA 79—10—7 (WETOX or FSUBS; or Acrylic acidCHOXD) Lb INCINCARBN; orINC IN
13010 NA 50-07-7 (WETOX or INCIN Mitomycin CCHOXD) fbCARBN; orINCIN
79
U011 NA 61-82—5 (WETOX or INCIN AmitroleCMOXD) LbCARBN; orINCIN
13014 NA 492-80-8 (WETOX or INCIN AuramineCHOXD) LbCARBN; orINCIN
13015 NA 115-02-6 (WETOX or INCIN AzaserineCF!OXD) fbCARBN; orINCIN
U0l6 NA 225-51-4 (WETOX or FSUBS; or Benz(c)acridineCMOXD) lb INCINCARBN; orINCIN
13017 NA 98-87—3 (WETOX or INCIN Benzal chlorideCMOXD) LbCARBN; orINCIN
13020 NA 98—09—9 (WETOX or INCIN Benzenesulfonyl chlorideCHOXD) LbCARBN; orINCIN
1t021 NA 92-87—5 (WETOX or INCIN BenzidineCHOX!)) LbCARBN; orINCIN
U023 NA 98-07—7 CHOXD; CR— FSUBS; CM- BenzotrichlorideRED; OXD;CARBN; CHRED; orBIODG; or INCININCIN
13026 NA 494-03-1 (WETOX or INCIN ChlornaphazinCHOXD) fbCARBN; orINCIN
U033 NA 353—50-4 (WETOX or INCIN Carbonyl fluorideCHOX!)) LbCARBN; orINCIN
U034 NA 75—87—6 (WETOX or INCIN TrichloroacetaldehydeCHOXD) Lb (Chloral)CARBN; orINC IN
13035 NA 305-03—3 (WETOX or INCIN ChlorambucilCHOXD) lbCARBN; orINCIN
13038 Table B 510—15—6 NA INCIN Chlorobenzilate
80
U041 NA 106—89-8 (WETOX or INCIN 1—Chloro—2,3—epoxy—CHOXD) fb propane (Epichloro—CAftaN; or hydrin)INCIN
U042 Table B 110—75-8 NA INCIN 2-Chloroethyl vinylether
13046 NA 107-30-2 (WETOX or INCIN Chloromethyl methylCHOXD) Lb etherCARBN; orINCIN
U049 NA 3165—93—3 (WETOX or INCIN 4-Chloro-o—toluidineCHOX!)) Lb hydrochlorideCARBN; orINCIN
U053 NA 4170—30—3 (WETOX or FSUBS; or CrotonaldehydeCHOXD) fb INCINCARBN; orINCIN
U055 NA 98-82-8 (WETOX or FSUBS; or CumeneCHOXD) Lb INCINCARBN; orINCIN
13056 NA 110—82—7 (WETOX or FSUBS; or CyclohexaneCHOXD) Lb INCINCARBN; orINC IN
U057 Table B 108—94-1 NA FSUBS; or CyclohexanoneINCIN
U058 NA 50-18—0 CARBN; or FSUBS; or CyclophosphamideINCIN INCIN
13059 NA 20830—81-3 (WETOX or INCIN DaunomycinCHOXD) LbCARBN; orINCIN
13062 NA 2303—16—4 (WETOX or INCIN DiallateCHOXD) fbCARBN; orINCIN
U064 NA 189—55—9 (WETOX or FSUBS; or 1,2,7,8—DibenzopyreneCHOXD) Lb INCINCARBN; orINCIN
U073 NA 91-94—1 (WETOX or INCIN 3,3’-Dichloroben~idineCHOXD) lbCARBN; orINCIN
81
U074 NA 1476—11—5 (WETOX or INCIN cis—1,4—Dichloro—2—bu—CHOXD) Lb tene; trans—1,4-Di-CARBN; or chloro-2-buteneINCIN
UO85 NA 1464-53—5 (WETOX or FSUBS; or 1,2:3,4—DiepoxybutaneCHOXD) fb INCINCARBN; orINCIN
13086 NA 2.62.5-80—1 CHOXD; FSUBS; N,N-DiethylhydrazineCHRED; CMOXD;CARBN; CHREP; orBIODG; or INCININCIN
13087 NA 3288-58-2 CARBN; or FSUBS; or 0,0-Diethyl S—methyl-INCIN INCIN dithiophosphate
13089 NA 56—53—1 (WETOX or PSUBS; or Diethyl stilbestrolCHOXD) fb INCINCARBN; orINCIN
U090 NA 94—58—6 (WETOX or FSUBS; or DihydrosafroleCHOXD) Lb INCINCARBN; orINCIN
U091 NA 2.19—90-4 (WETOX or INCIN 3,3’—DimethoxybenzidineCHOXD) lbCARBN; orINCIN
U092 NA 124—40-3 (WETOX or INCIN DimethylamineCHOXD) lbCARBN; orINCIN
U093 Table B 621—90-9 NA INCIN p-Dimethylaminoazo-benzene
13094 NA 57—97—6 (WETOX or FSUBS; or 7,12—Dimethylbenz(a)—CMOXD) Lb INCIN anthraceneCARBN; orINCIN
13095 NA 119-93-7 (WETOX or INCIN 3,3’—DimethylbenzidineCHOXD) lbCARBN; orINCIN
13096 NA 80—15—9 CHOXD; FSUBS; alpha,alpha—Dimethyl-CHRED; CHOXD; benzyl hydroperoxideCARBN; CHRED; orBIODG; or INCININCIN
U097 NA 79—44—7 (WETOX or INCIN Dimethylcarbamoyl chlor-CHOXD) Lb ideCARBN; orINCIN
82
U098 NA 57-14-7 CHOXD; CM- FSUBS; CM- 1,1-DiniethylhydrazineRED; OXD;CARBN; CHRED; orBIODG; or INCININCIN
U099 NA 540—73—8 CHOXD; CM- FSUBS; CM— 1,2-DimethylhydrazineRED; OX!);CARBN; CHRED; orBIODG; or INCININCIN
U103 NA 77-78-1 CHOXD; CM- FSUBS; CH— Dimethyl sulfateRED; OX!);CARBN; CHRED; orBIODG; or INCININCIN
13109 NA 122—66—7 CHOXD; CM- FSUBS; CM— 1,2-DiphenylhydrazineRED; OXD;CARBN; CHRED; orBIODG; or INCININCIN
U110 NA 142—84-7 (WETOX or INCIN DipropylamineCHOXD) LbCARBN; orINCIN
13113 NA 140—88-5 (WETOX or FSUBS; or Ethyl acrylateCHOXD) Lb INCINCARBN; orINCIN
13114 NA 12.1—54-6 (WETOX or INCIN Ethylenebisdithio—CHOXB) fb carbamic acidCARBN; orINCIN
13115 NA 75-21—8 (WETOX or CHOXD; or Ethylene oxideCHOXD) Lb INCINCARBN; orINCIN
13116 NA 96-45-7 (WETOX or INCIN Ethylene thioureaCHOXD) LbCARBN; orINCIN
U119 NA 62-50—0 (WETOX or INCIN Ethyl methanesulfonateCHOXD) LbCARBN; orINCIN
13122 NA 50-00—0 (WETOX or FSUBS; or FormaldehydeCHOXD) Lb INCINCARBN; orINCIN
83
U123 NA 64-18—6 (WETOX or FSUBS; or Formic acidCHOXD) Lb INCINCARBN; orINCIN
U124 NA 110—00-9 (WETOX or FSUBS; or FuranCHOXD) lb INCINCARBN; orINCIN
U125 NA 98-01-1 (WETOX or FSUBS; or FurfuralCHOXD) Lb INCINCARBN; orINCIN
13126 NA 765—34-4 (WETOX or FSUBS; or GlycidaldehydeCMOXD) Lb INCINCARBN; orINCIN
U132 NA 70—30-4 (WETOX or INCIN HexachloropherteCHOXD) lbCARBN; orINCIN
U133 NA 302-01—2 CHOXD; FSUBS; HydrazineCHRED; CHOXD;CARBN; CHRED; orBIODG; or INCININCIN
U134 Table B 7664-39—3 NA ADGAS Lb Hydrogen FluorideNEUTR; orNEUTR
U135 NA 7783-06-4 CHOXD; CM- CMOXD; CM— Hydrogen SulfideRED; or RED; orINCIN INCIN
13143 NA 303-34-4 (WETOX or INCIN LasiocarpineCMOXP) LbCARBN; orINC IN
U147 NA 108-31-6 (WETOX or FSUBS; or l4aleic anhydrideCHOXD) Lb INCINCARBN; orINCIN
13148 NA 123-33—1 (WETOX or INCIN Maleic hydrazideCHOXD) LbCARBN; orINCIN
13149 NA 109—77-3 (WETOX or INCIN l4alononitrileCHOXD) LbCARBN; orINCIN
84
13150 NA 148—82—3 (WETOX or INCIN MelphalanCHOXD) LbCARBN; orINCIN
U151 Tables A 7439-97—6 NA RNERC Mercury: (High Mercury& B Subcategory——greater
than or equal to 260mg/kg total Mercury)
13153 NA 74-93—1 (WETOX or INCIN MethanethiolCHOXD) LbCARBN; orINCIN
U154 NA 67—56—1 (WETOX or FSUBS; or MethanolCHOXD) Lb INCINCARBN; orINCIN
U156 NA 79—22—1 (WETOX or INCIN Methyl chlorocarbonateCHOXD) LbCARBN; orINCIN
U160 NA 1338-23-4 CHOXD; FSUBS; Methyl ethyl ketone per—CHRED; CHOXD; oxideCARBN; CHRED; orBIODG; or INCININCIN
U163 NA 70—25—7 (WETOX or INCIN N—Methyl-N’—nitro-N—CHOXD) Lb NitrosoguanidineCARBN; orINCIN
13164 NA 56—04—2 (WETOX or INCIN MethylthiouracilCHOXD) LbCABBN; orINCIN
U166 NA 130—15—4 (WETOX or FSUBS; or 1,4-NaphthoquinoneCHOXD) lb INCINCARBN; orINCIN
13167 NA 134-32—7 (WETOX or INCIN 1—NaphthylamineCMOXD) lbCARBN; orINCIN
U168 Table B 91—59—8 NA INCIN 2—Naphthylamine
U171 NA 79—46—9 (WETOX or INCIN 2—NitropropaneCHOXD) LbCARBN; orINCIN
U173 NA 1116-54—7 (WETOX or INCIN N—Nitroso—diethanolamineCHOXD) lbCARBN; orINCIN
85
13176 NA 759-73—9 (WETOX or INCIN N-Nitroso—N—ethylureaCHOXD) fbCARBN; orINCIN
13177 NA 684-93—5 (WETOX or INCIN N-Nitroso—N—methylureaCMOXD) LbCARBN; orINCIN
13178 NA 615-53—2 (WETOX or INCIN N-Nitroso-N-methyl-CMOXD) lb urethaneCARBN; orINC IN
13182 NA 123-63—7 (WETOX or FSUBS; or ParaldehydeCHOXD) Lb INCINCARBN; orINCIN
U184 NA 76—01—7 (WETOX or INCIN PentachloroethaneCHOXD) lbCARBN; orINC IN
U186 NA 504-60—9 (WETOX or FSUBS; or 1,3—PentadieneCHOXD) fb INCINCARBN; orINCIN
132.89 NA 1314—80—3 CHOXD; CM— CHOXD; CM- Phosphorus sulfideRED; or RED; orINCIN INCIN
13191 NA 109-06-8 (WETOX or INCIN 2-PicolineCMOXD) LbCARBN; orINCIN
0193 NA 1120-71—4 (WETOX or INCIN 1,3-Propane sultoneCHOXD) LbCARBN; orINCIN
13194 NA 107-10-8 (WETOX or INCIN n-PropylamineCMOXD) LbCARBN; orINCIN
0197 NA 106-51-4 (WETOX or FSUBS; or p-BenzoquinoneCHOXD) Lb INCINCARBN; orINCIN
0200 NA 50-55—5 (WETOX or INCIN ReserpineCHOXD) LbCARBN; orINCIN
86
13201 NA 108—46-3 (WETOX or FSUBS; or ResorcinolCHOXD) Lb INCINCARBN; orINCIN
U202 NA 81-07—2 A (WETOX or INCIN Saccharin and saltsCHOXD) lbCARBN; orINC IN
U206 NA 18883—66-4 (WETOX or INCIN StreptozatocinCHOXD) lbCARBN; orINCIN
13213 NA 109—99—9 (WETOX or PSUBS; or TetrahydrofuranCHOXD) fb INCINCARBN; orINCIN
0214 Table B 563—68—8 NA RTHRM; or Thallium (I) acetateSTABL
13215 Table B 6533—73—9 NA RTMRM; or Thallium (I) carbonateSTABL
0216 Table B 7791—12—0 NA RTHRM; or Thallium (I) chlorideSTABL
U217 Table B 102.02—45—1 NA RTHRM; or Thallium (I) nitrateSTABL
0218 NA 62-55—5 (WETOX or INCIN ThioacetamideCMOXD) LbCARBN; orINCIN
13219 NA 62—56—6 (WETOX or INCIN ThioureaCHOXD) LbCARBN; orINCIN
0221 NA 25376—45—8 CARBN; or FSUBS; or ToluenediamineINCIN INCIN
15222 NA 636—21-5 (WETOX or INCIN o-Toluidine hydro—CMOXD) Lb chlorideCARBN; orINCIN
0223 NA 26471-62—5 CARBN; or FSUBS; or Toluene diisocyanateINCIN INCIN
0234 NA 99—35—4 (WETOX or INCIN sym—TrinitrobenzeneCHOXP) LbCARBN; orINCIN
U236 NA 72-57-1 (WETOX or INCIN Trypan BlueCMOXD) lbCARBN; orINCIN
87
~3237 NA 66-75—1 (WETOX or INCIN Uracil mustardCHOXD) LbCARBN; orINCIN
U238 NA 51-79—6 (WETOX or INCIN Ethyl carbamateCHOX!)) lbCARBN; orINC IN
U240 NA 94_75_7* (WETOX or INCIN 2,4—Dichlorophenoxy-CHOXD) lb acetic acid (salts andCARBN; or esters)INCIM
13244 NA 137—26-8 (WETOX or INCIN ThiramCHOXD) lbCARBN; orINCIN
U246 NA 506-68-3 CHOXD; CHOXD; Cyanogen bromideWETOX; or WETOX; orINCIN INCIN
U248 NA 81-81-2 (WETOX or FSUBS; or Warfarin (0.3% or less)CHOXD) lb INCINCARBN; orINCIN
13249 NA 1314—84—7 CHOXD; CM— CHOXD; CM- Zinc Phosphide (<10%)RED; or RED; orINCIN INCIN
U328 NA 95—53-4 INCIN; or INCIN; or o—toluidineCHOXD fb, Thermal(BIODG or DestructioCARBN); or n.BIODG lbCARBN
U353 NA 106-49—0 INCIN; or INCIN; or p—toluidineCHOXD lb, Thermal(BIODG or DestructioCAREN); or n.BIODG LbCARBN
13359 NA 110-80—5 INCIN; or INCIN; or 2—ethoxy-ethanolCHOXDfb, FSUBS.(BIODG orCARBN); orBIODG LbCARBN
A CAS Number given for parent compound only.
B This waste code exists in gaseous form and is not categorized aswastewater or nonwastewater forms.
NA Not Applicable.
BOARD NOTE: When a combination of these technologies (i.e., a treatment
88
train) is specified as a single treatment standard, the order of applicationis specified in this Table by indicating the five letter technology code thatmust be applied first, then the designation “fb” (an abbreviation for “Fol-lowed by”), then the five letter technology code for the technology that mustbe applied next, and so on. When more than one technology (or treatmenttrain) are specified a alternative treatment standards, the five lettertechnology codes (or the treatment trains) are separated by a semicolon (;)with the last technology preceded by the word “or”. This indicates that anyone of these BDAT technologies or treatment trains can be used for compliancewith the standard. See Section 728..Table C for a listing of the technologycodes and technology—based treatment standards. Derived from 40 CFR 268.42,Table 2 (1992), as amended at 57 Fed. Reg. 37273 (Aug. 18, 1992) and 59 Fed.Req. 32.552 (June 20, 1994).
(Source: Amended at Ill. Reg. _________, effective
TITLE 35: ENVIRONMENTALPROTECTIONSUBTITLE C: WASTE DISPOSAL
CHAPTER I: POLLUTION CONTROLBOARDSUBCHAPTERc: HAZARDOUSWASTEOPERATINGREQUIREMENTS
PART 739STANDARDSFOR THE MANAGEMENTOF USED OIL
SUBPARTA: DEFINITIONSSection739.100 Definitions
SUBPART B: APPLICABILITYSection739.110 Applicability739.111 Used oil specifications739.112 Prohibitions
SUBPARTC: STANDARDSFOR USED OIL GENERATORSSect ion739.120 Applicability739.121 Hazardous waste mixing739.122 Used oil storage739.123 On-site burning in space heaters739.124 Off—site shipments
SUBPART D: STANDARDSFOR USED OIL COLLECTION CENTERSANDAGGREGATIONPOINTS
Section739.130 Do-it-yourselfer used oil collection centers739.132. Used oil collection centers739.132 Used oil aggregate points owned by the generator
SUBPART E: STANDARDSFOR USED OIL TRANSPORTERAND TRANSFERFACILITIES
Section739.140 Applicability739.141 Restrictions on transporters that are not also processors739.142 Notification739.143 Used oil transportation739.144 Rebuttable presumption for used oil739.145 Used oil storage at transfer facilities739.146 Tracking739.147 Management of residues
89
SUBPART F: STANDARDSFOR USED OIL PROCESSORSSect ion739.150 Applicability739.151 Notification739.152 General facility standards739.153 Rebuttable presumption for used oil739.154 Used oil management739.155 Analysis plan739.156 Tracking739.157 Operating record and reporting739.158 Off—site shipments of used oil739.159 Management of residues
SUBPART G: STANDARDSFOR USED OIL BURNERSTHAT BURNOFF-SPECIFICATION USED OIL FOR ENERGYRECOVERY
Section739.160 Applicability739.161 Restriction on burning739.162 Notification739.163 Rebuttable presumption for used oil739.164 Used oil storage739.165 Tracking739.166 Notices739.167 Management of residues
SUBPART H: STANDARDSFOR USED OIL FUEL MARKETERSSection739.170 Applicability739 • 171 Prohibitions739.172 On—specification used oil Luel739.173 Notification739.174 Tracking739.175 Notices
SUBPART I: STANDARDSFOR USE AS A DUST SUPPRESSANTDISPOSAL OF USED OILSection739. 180 Applicability739.181 Disposal739.182 Use as a duet suppressant
AUTHORITY: Implementing Section 22.4 and authorized by Section 27 of theEnvironmental Protection Act (Ill. flcv. Ctat. 2.~2., ch. 111½, par3. 1022.4 and1027 (415 ILCS 5/22.4 and 5/27]+.
SOURCE: Adopted in R93—4 at 17 Ill. Reg. 20954, effective November 22, 1993;amended in R93—16 at 18 Ill. Reg. 6931, effective April 26, 1994; amended inR94-17 at Ill. Req. , effective
SUBPART A: DEFINITIONS
Section 739.100 Definitions
Terms that are defined in 35 Ill. Adm. Code 720.110, 721.101, and 731.112 havethe same meanings when used in this Part.
“Aboveground tank” means a tank used to store or process used oilthat is not an underground storage tank as defined in 35 Ill. Adm.Code 280.12.BOARD NOTE: This definition is different from the definition for“Aboveground tank” given in 35 Ill. Adm. Code 720.110. Althoughthe meanings are similar, the main distinction is that the
90
definition for this Part limits the tanks to those used to storeor process used oil, whereas the 720.110 definition contemplatestanks whiohthat contain hazardous wastes. The above definition islimited to this Part only.
“Container” means any portable device in which a material isstored, transported, treated, disposed of, or otherwise handled.
“Do—it—yourselfer used oil collection center” means any site orfacility that accepts or aggregates and stores used oil collectedonly from household do—it—yourself ers.
“Existing tank” means a tank that is used for the storage orprocessing of used oil and that is in operation, or for whichinstallation has commenced on or prior to the effective date ofthe authorized used oil program for the State in which the tank islocated. Installation will be considered to have commenced if theowner or operator has obtained all federal, state, and localapprovals or permits necessary to begin installation of the tankand if either:
A continuous on—site installation program has begun, or
The owner or operator has entered into contractualobligations—which that cannot be canceled or modifiedwithout substantial loss—_for installation of the tank to becompleted within a reasonable time.BOARD NOTE: This definition is similar to the definitionfor “Existing tank system” in 35 Ill. Adm. Code 720.110.Although the meanings are similar, the definition givenabove for “existing tank” in this Part limits the tanks tothose used to store or process used oil, whereas the 720.12.0definition contemplates tanks systems whichthat containhazardous wastes. The above definition is limited to thisPart only.
“Household ‘do-it—yourselfer’ used oil” means oil that is derivedfrom households, such as used oil generated by individuals whogenerate used oil through the maintenance of their personalvehicles.BOARD NOTE: Household ‘do—it-yourselfer’ used oil is not subjectto the State’s special waste hauling permit requirements underPart 809.
“Household ~do—it—yourselfer’ used oil generator” means anindividual who generates household “do—it—yourself er” used oil.
“New tank” means a tank that will be used to store or process usedoil and for which installation has commenced after the effectivedate of the authorized used oil program for the State in which thetank is located.BOARD NOTE: This definition is similar to the definition givenfor “New tank system” given in 35 Ill. Adm. Code 720.110.Although the meanings are similar, the definition given above for“new tank” in this Part limits the tanks to those used to store orprocess used oil, whereas the 720.110 definition contemplates newtanks systems which contain hazardous wastes. The abovedefinition is limited to this Part only.
“Petroleum refining facility” means an establishment primarilyengaged in producing gasoline, kerosene. distillate fuel oils,residual fuel oils, and lubricants, throuah fractionation,
91
straight distillation of crude oil, redistillation of unfinishedpetroleum derivatives, cracking, or other processes (i.e.,facilities classified as SIC 2911).
“Processing” means chemical or physical operations designed toproduce from used oil, or to make used oil more amenable forproduction of, fuel oils, lubricants, or other used oil—derivedproduct. Processing includes, but is not limited to: blendingused oil with virgin petroleum products, blending used oils tomeet the fuel specification, filtration, simple distillation,chemical or physical separation4, and re—refining.
“Re—refining distillation bottoms” means the heavy fractionproduced by vacuum distillation of filtered and dehydrated usedoil. The composition of still bottoms varies with columnoperation and feedstock.
“Tank” means any stationary device, designed to contain anaccumulation of used oil which is constructed primarily of non—earthen materials, (e.g., wood, concrete, steel, plastic) whichprovides structural support.
“Used oil” means any oil that has been refined from crude oil, orany synthetic oil, that has been used and as a result of such useis contaminated by physical or chemical impurities.
“Used oil aggregation point” means any site or facility thataccepts, aggregates, or stores used oil collected only from otherused oil generation sites owned or operated by the owner oroperator of the aggregation point, from which used oil istransported to the aggregation point in shipments of no more than55 gallons. Used oil aggregation points may also accept used oilfrom household do—it—yourselfere.
“Used oil burner” means a facility where used oil not meeting thespecification requirements in Section 739.111 is burned for energyrecovery in devices identified in Section 739.161(a).
“Used oil collection center” means any site or facility that isregistered by the Agency to manage used oil and accepts oraggregates and stores used oil collected from used oil generatorsregulated under Subpart C of this Part that bring used oil to thecollection center in shipments of no more than 55 gallons underthe provisions of Section 739.124. Used oil collection centersmay also accept used oil from household do—it-yourselfers.
“Used oil fuel marketer” means any person that conducts either ofthe following activities:
Directs a shipment of off—specification used oil from theirfacility to a used oil burner; or
First claims that used oil that is to be burned for energyrecovery meets the used oil fuel specifications set forth inSection 739.111.
“Used oil generator” means any person, by site, whose act orprocess produces used oil or whose act first causes used oil tobecome subject to regulation.
“Used oil processor” means a facility that processes used oil.
92
“Used oil transfer facility” means any transportation~relatedfacility including loading docks, parking areas, storage areas,and other areas where shipments of used oil are held for more than24 hours during the normal oouroo of transportation and not longerthan 35 days during the normal course of transportation or nriorto an activity performed pursuant to Section 739.120(b) (2).Transfer facilities that store used oil for more than 35 days aresubject to regulation under Subpart F of this Part.
“Used oil transporter” means any person that transports used oil,any person that collects used oil from more than one generator andthat transports the collected oil, and owners and operators ofused oil transfer facilities. Used oil transporters mayconsolidate or aggregate loads of used oil for purposes oftransportation but, with the following exception, may not processused oil. Transporters may conduct incidental processingoperations that occur in the normal course of used oiltransportation (e.g., settling and water separation), but that arenot designed to produce (or make more amenable for production of)used oil derived products or used oil fuel.
(Source: Amended at Ill. Reg. _________, effective
SUBPART B: APPLICABILITY
Section 739.110 Applicability
This Section identifies those materials which are subject to regulation asused oil under this Part. This Section also identifies some materials thatare not subject to regulation as used oil under this Part, and indicateswhether these materials may be subject to regulation as hazardous waste underParts 702, 703, 720 through 7264, and 728.
a) Used oil. U.S. EPA presumes that used oil is to be recycledunless a used oil handler disposes of used oil, or sends used oilfor disposal. Except as provided in Section 739.111, theregulations of this Part apply to used oil, and to materialsidentified in this Section as being subject to regulation as usedoil, whether or not the used oil or material exhibits anycharacteristics of hazardous waste identified in 35 Ill. Adm. Code721.Subpart C.
b) Mixtures of used oil and hazardous waste.
1) Listed hazardous waste.
A) A mixture of used oil and hazardous waste that islisted in 35 Ill. Adm. Code 721.Subpart D iB subjectto regulation as hazardous waste under 35 Ill. Adm.Code 703, 720 through 7264, and 728, rather than asused oil under this Part.
B) Rebuttable presumption for used oil. Used oilcontaining more than 1,000 ppm total halogens iapresumed to be a hazardous waste because it has beenmixed with halogenated hazardous waste listed in 35Ill. Adm. Code 721.Subpart D. Persons may rebut thispresumption by demonstrating that the used oil doesnot contain hazardous waste (for example, by using ananalytical method from SW—846, Edition III, to show
93
that the used oil does not contain significantconcentrations of halogenated hazardous constituentslisted in 35 Ill. Adm. Code 721.Appendix H). U.S. EPAPublication SW—846, Third Edition, is available ~e*the cost of ~110.0O from the Government PrintingOffice, Superintendent of Documents, P.O. Box 371954,Pittsburgh, PA 15250—7954, (202) 783—3238 (documentnumber 955—001—00000—1).
i) The rebuttable presumption does not apply tometalworking oils or fluids containingchlorinated paraf I ins, if they are processed,through a tolling arrangement as described inSection 739.124(c), to reclaim metalworking oilsor fluids. The presumption does apply tometalworking oils or fluids if such oils orfluids are recycled in any other manner, ordisposed.
ii) The rebuttable presumption does not apply toused oils contaminated with chiorofluorocarbons(CFC5) removed from refrigeration units wherethe CFC5 are destined for reclamation. Therebuttable presumption does apply to used oilscontaminated with CFCs that have been mixed withused oil from sources other than refrigerationunits.
2) Characteristic hazardous waste. A mixture of used oil andhazardous waste that exhibits a hazardous wastecharacteristic identified in 35 Ill. Adm. Code 721.Subpart Cand a mixture of used oil and hazardous waste that is listedin Subpart D of this Part solely because it exhibits one ormore of the characteristics of hazardous waste identified in35 Ill. Adm. Code 721.Subpart C is subject to:
A) Except as provided in subsection (b)(2)(C) of thisSection, regulation as hazardous waste under 35 Ill.Adm. Code 703, 720 through 7264, and 728 rather than asused oil under this Part, if the resultant mixtureexhibits any characteristics of hazardous wasteidentified in 35 Ill. Adm. Code 721.Subpart C; or
B) Except as provided in subsection (b)(2)(C) of thisSection, regulation as used oil under this Part, ifthe resultant mixture does not exhibit anycharacteristics of hazardous waste identified under 35Ill. Adm. Code 721.Subpart C.
C) Regulation as used oil under this Part, if the mixtureis of used oil and a waste which is hazardous solelybecause it exhibits the characteristic of ignitabilityand is not liatcd in 35 Ill. Z~.dm. Oodc 721.Cubpart D(e.g., ignitable—only mineral spirits), provided thatthe resultant mixture does not exhibit thecharacteristic of ignitability under 35 Ill. Adin. Code721. 121.
3) Conditionally exempt small quantity generator hazardouswaste. A mixture of used oil and conditionally exempt smallquantity generator hazardous waste regulated under 35 Ill.Adm. Code 721.105 is subject to regulation as used oil under
94
this Part.
c) Materials containing or otherwise contaminated with used oil.-1-
1) Except as provided in subsection (c)(2) of this Section, amaterial containing or otherwise contaminated with used oilfrom which the used oil has been properly drained or removedto the extent possible such that no visible signs of free—flowing oil remain in or on the material:
A) Is not used oil, and thus, it is not subject to thiBPart, and
B) If applicable, is subject to the hazardous wasteregulations of 35 Ill. Adm. Code 703, 705, 720 through726, and 728.
2) A material containing or otherwise contaminated with usedoil that is burned for energy recovery is subject toregulation as used oil under this Part.
3) Used oil drained or removed from materials containing orotherwise contaminated with used oil is subject toregulation as used oil under this Part.
d) Mixtures of used oil with products.
1) Except as provided in subsection (d)(2) below, mixtures ofused oil and fuels or other fuel products are subject toregulation as used oil under this Part.
2) Mixtures of used oil and diesel fuel mixed on—site by thegenerator of the used oil for use in the generator’s ownvehicles are not subject to this Part once the used oil anddiesel fuel have been mixed. Prior to mixing, the used oilis subject to the requirements of Subpart C of this Part.
e) Materials derived from used oil.
1) Materials that are reclaimed from used oil that are usedbeneficially and are not burned for energy recovery or usedin a manner constituting disposal (e.g., re—refinedlubricants) are:
A) Not used oil and thus are not subject to this Part,and
B) Not solid wastes and are thus not subject to thehazardous waste regulations of Parts 35 Ill. Adm. Code703, 720 through 7262. and 728 as provided in 35 Ill.Adm. Code 721.103(c) (2) (A).
2) Materials produced from used oil that are burned for energyrecovery (e.g., used oil fuels) are subject to regulation asused oil under this Part.
3) Except as provided in subsection (e)(4) below, materialsderived from used oil that are disposed of or used in amanner constituting disposal are:
A) Not used oil and thus are not subject to this Part,and
95
B) Are solid wastes and thus are subject to the hazardouswaste regulations of 35 Ill. Adm. Code 703, 720through 7262. and 728 if the materials are listed oridentified as hazardous waste.
4) Used oil re—refining distillation bottoms that are used asfeedstock to manufacture asphalt products are not subject tothis Part.
f) Wastewater. Wastewater, the discharge of which is subject toregulation under either Section 402 or Section 307(b) of the CleanWater Act (including wastewaters at facilities which haveeliminated the discharge of wastewater), contaminated with deminimis quantities of used oil are not subject to the requirementsof this Part. For purposes of this subsection, “de minimis”quantities of used oils are defined as small spills, leaks, ordrippings from pumps, machinery, pipes, and other similarequipment during normal operations or small amounts of oil lost tothe wastewater treatment system during washing or drainingoperations. This exception will not apply if the used oil isdiscarded as a result of abnormal manufacturing operationsresulting in substantial leaks, spills, or other releases, or toused oil recovered from wastewaters.
g) Used oil introduced into crude oil or natural gas pipelines or apetroleum refining facility.—
fl Used oil that is placed dirostlymixed with crude oil ornatural ~as liauids (e.g., in p production separator orcrude oil stock tank) for insertion into a crude oil e*natural gas pipeline is subject to the man~igcxnont standardsof this Part only prior to the point of introduction to thepipeline. Once the used oil is introduced to th~ pipeline,the material is exempt from the requirements of this Part._The used oil is sublect to the reauirements of this Partprior to the mixing of used oil with crude oil or naturalgas lici-uids.
~j Mixtures of used oil and crude oil or natural gag liauidscontaining less than 1% used oil that are being stored ortransported to p crude oil pipeline or petroleum refiningfacility for insertion into the refining process at a pointprior to crude distillation or catalytic cracking are exemptfrom the requirements of this Part.
~j Used oil that is inserted into the Petroleum refiningprocess before crude distillation or catalytic crackingwithout prior mixing with crude oil is exempt from therequirements of this Part, provided that the used oilcontains less than 1% of the crude oil feed to any petroleumrefining facility process unit at any given time. Prior toinsertion into the petroleum refining process, the used oilis sub-ject to the re~irements of this Part.
il Except as provided in subsection (g)(5) below, used oil thatis introduced into a petroleum refining facility processafter crude distillation or catalytic crackin~ is exemptfrom the requirements of this Part only if the used oilmeets the specification of Section 739.111. Prior toinsertion into the ~etro1eum refining facility Process~ theused oil is sublect to the requirements of this Part.
96
j) Used oil.that is incidentally captured by a hydrocarbonrecovery system or wastewater treatment system as part ofroutine process operations at a petroleum refining facilityand inserted into the petroleum refining facility process isexempt from the requirements of this Part. This exemptiondoes not extend to used oil that is intentionally introducedinto a hydrocarbon recovery system (e.g.. by pouringcollected used oil into the wastewater treatment system).
~ Tank bottoms from stock tanks containing exempt mixtures ofused oil and crude oil or natural gas liquids are exemptfrom the requirements of this Part.
h) Used oil on vessels. Used oil produced on vessels from normalshipboard operations is not subject to this Part until it istransported ashore.
i) Used oil containing PCBs. In addition to the requirements of thisPart, a marketer or burner of used oil that markets used oilcontaining any quantifiable level of PCBs is subject to therequirements of 40 CFR 761.20(e).
(Source: Amended at Ill. Reg. _________, effective
SUBPARTC: STANDARDSFOR USED OIL GENERATORS
Section 739.120 Applicability
a) General. This subpart applies to all generators of used oil,except:
1) Household “do—it—yourselfer” used oil generators. Household“do—it—yourself er” used oil generators are not subject toregulation under this Part.
2) Vessels. Vessels at sea or at port are not subject to thisSubpart. For purposes of this Subpart, used oil produced onvessels from normal shipboard operations is considered to begenerated at the time it is transported ashore. The owneror operator of the vessel and the person(s) removing oraccepting used oil from the vessel are co—generators of theused oil and are both responsible for managing the waste incompliance with this Subpart once the used oil istransported ashore. The co—generators may decide among themwhich party will fulfill the requirements of this Subpart.
3) Diesel fuel. Mixtures of used oil and diesel fuel mixed bythe generator of the used oil for use in the generator’s ownvehicles are not subject to this Part once the used oil anddiesel fuel have been mixed. Prior to mixing, the used oilfuel is subject to the requirements of this Subpart.
4) Farmers. Farmers who generate an average of 25 gallons permonth or less of used oil from vehicles or machinery used onthe farm in a calendar year are not subject to therequirements of this Part.
b) Other applicable provisions. U~_gsed oil generators whethatconducts any of the following activities a*ej~ subject to therequirements of other applicable provisions of this Part asindicated in subsections (b)(1) through (5) below:
97
1) G~eneratore whethat transport~ used oil, except under theself—transport provisions of Section 739.124 (a) and (b),rnustshall also comply with 739.Subpart E.
2) G~eneratore whethat process~ or re—ref ine~ used oil4,
~j. Except as provided in subsection (b)(2)(B) below, agenerator that processes or re—refines used oil shallmust also comply with 739.Subpart F.
~j A generator that performs the following activities isnot a used oil processor, provided that the used oilis generated on—site and is not being sent off—site toa burner of on- or off—specification used oil fuel:
fl Filtering, cleaning, or otherwise reconditioningused oil before returning it for reuse by thegenerator
JJJ. Separating used oil from wastewater generatedon—site to make the wastewater acceptable fordischarge or reuse pursuant to Section 402 or307(b) for the federal Clean Water Act (33U.S.C. 1317 or 1342), 40 CFR 403 through 499, or35 Ill. Adrn. Code 310 or 309, governing thedischarge of wastewaters;
iii) Using oil mist collectors to remove smalldroplets of used oil from in-plant air to make~1ant air suitable for continued recirculation
~ Draining or otherwise removing used oil frommaterials containing or otherwise contaminatedwith used oil in order to remove excessive oilto the extent possible pursuant to Section739.110(c); or
~J_ Filtering, seoarating, or otherwisereconditioning used oil before burning it in aspace heater pursuant to Section 739.123.
3) G~generator whethat burn~ off—specification used oil forenergy recovery, except under the on—site space heaterprovisions of Section 739.123, muotshall also comply with739.Subpart G.
4) G~enerator whethat direct~ shipments of off—specificationused oil from their facility to a used oil burner or firstclaim~ that used oil that is to be burned for energyrecovery meets the used oil fuel specifications set forth inSection 739.111 mustshall also comply with 739.Subpart H.
5) G~enerator whethat dispose,~ of used oil, including the useof used oil as a dust suppressant, muotshall also complywith 739.Subpart I.
(Source: Amended at _____ Ill. Reg. _________, effective
SUBPART E: STANDARDSFOR USED OIL TRANSPORTERANDTRANSFERFACILITIES
98
Section 739.141 Restrictions on transporters that are not also processors
a) Used oil transporters may consolidate or aggregate loads of usedoil for purposes of transportation. However, except as providedin subsection (b) of this Section, used oil transporters may notprocess used oil unless they also comply with the requirements forprocessors in Subpart F of this Part.
b) Transporters may conduct incidental processing operations thatoccur in the normal course of used oil transportation (e.g.,settling and water separation), but that are not designed toproduce (or make more amenable for production of) used oil derivedproducts unless they also comply with the processor requirementsin Subpart F of this Part.
~ Transporters of used oil that is removed from oil—bearingelectrical transformers and turbines and which is filtered by thetransporter or at p transfer facility prior to being returned toits original use are not sublect to the processor and re—refinerrequirements in 739.Subpart F.
(Source: Amended at Ill. Reg. _________, effective
Section 739.144 Rebuttable presumption for used oil
a) To ensure that used oil is not a hazardous waste under therebuttable presumption of Section 739.1l0(b)(1)(ii), the used oiltransporter muatshall determine whether the total halogen contentof used oil being transporter or stored at a transfer facility isabove or below 1,000 ppm.
b) The transporter muotshall make this determination by:
1) Testing the used oil; or
2) Applying knowledge of the halogen content of the used oil inlight of the materials or processes used.
c) If the used oil contains greater than or equal to 1,000 ppm totalhalogens, it is presumed to be a hazardous waste because it hasbeen mixed with halogenated hazardous waste listed in 35 Ill. Adm.Code 721.Subpart D. The owner or operator may rebut thepresumption by demonstrating that the used oil does not containhazardous waste (for example, by using an analytical method fromSW—846, Edition III, to show that the used oil does not containsignificant concentrations of halogenated hazardous constituentBlisted in 35 Ill. Adm. Code 721.Appendix H). U.S. EPA PublicationSW—846, Third Edition, is available -for the coot of ~1l0.00 fromthe Government Printing Office, Superintendent of Documents, P0Box 371954, Pittsburgh, PA 15250—7954. (202) 783—3238 (documentnumber 955—001—00000—1).
1) The rebuttable presumption does not apply to metalworkingoils and fluids containing chlorinated paraf fins, if theyare processed, through a tolling arrangement as described inSection 739.124(c), to reclaim metalworking oils and fluids.The presumption does apply to metalworking oils and fluidsif such oils and fluids are recycled in any other manner, ordisposed.
2) The rebuttable presumption does not apply to used oils
99
contaminated with chlorofluorocarbons (CFC5) removed fromrefrigeration units if the CFC are destined for reclamation.The rebuttable presumption does apply to used oilscontaminated with CFCs that have been mixed with used oilfrom sources other than refrigeration units.
d) Record retention. Records of analyses conducted or informationused to comply with subsections (a), (b), and (C) of this Sectionmust be maintained by the transporter for at least 3 years.
(Source: Amended at Ill. Reg. ________, effective
Section 739.146 Tracking
a) Acceptance. Used oil transporters shall keep a record of eachused oil shipment accepted for transport. Records for eachshipment must include:
1) The name and address of the generator, transporter, orprocessor that provided the used oil for transport;
2) The U.S. EPA identification number and Illinois specialwaste identification number (if applicable) of thegenerator, transporter, or processor that provided the usedoil for transport;
3) The quantity of used oil accepted;
4) The date of acceptance; and
5) The signature4,
~j. Except as provided in subsection (a)(SUB) below, thesignature, dated upon receipt of the used oil, of arepresentative of the generator, transporter, orprocessor or re—refiner that provided the used oil fortransport.
~gj~ An intermediate rail transporter is not required tosign the record of acceptance.
b) Deliveries. Used oil transporters shall keep a record of eachshipment of used oil that is delivered to another used oiltransporter, or to a used oil burner, processor, or disposalfacility. Records of each delivery must include:
1) The name and address of the receiving facility ortransporter;
2) The U.S. EPA identification number and Illinois specialwaste identification number of the receiving facility ortransporter;
3) The quantity of used oil delivered;
4) The date of delivery;
5) The signature4,
~j Except as provided in subsection (b)(5)(B) below, thesignature, dated upon receipt of the used oil, of a
100
representative of the receiving facility ortransporter.
flJ. An intermediate rail transporter is not required tosian the record of acceptance.
c) Exports of used oil. Used oil transporters shall maintain therecords described in subsections (b)(1) through (b)(4) of thisSection for each shipment of used oil exported to any foreigncountry.
d) Record retention. The records described in subsections (a), (b),and (c) of this Section must be maintained for at least threeyears.
(Source: Amended at Ill. Reg. _________, effective
SUBPART F: STANDARDSFOR USED OIL PROCESSORS
Section 739.152 General facility standards
a) Preparedness and prevention. Owners and operators of used oilprocessors and re—refiners facilities shall. comply with thefollowing requirements:
1) Maintenance and operation of facility. Facilities must bemaintained and operated to minimize the possibility of afire, explosion, or any unplanned sudden or non—suddenrelease of used oil to air, soil, or surface water whichcould threaten human health or the environment.
2) Required equipment. All facilities must be equipped withthe following, unless none of the hazards posed by used oilhandled at the facility could require a particular kind ofequipment specified in subsections (a)(2)(A) through(a)(2)(D) of this Section:
A) An internal communications or alarm system capable ofproviding immediate emergency instruction (voice orsignal) to facility personnel;
B) A device, such as a telephone (immediately availableat the scene of operations) or a hand—held two—wayradio, capable of summoning emergency assistance fromlocal police departments, fire departments, or Stateor local emergency response teams;
C) Portable fire extinguishers, fire control equipment(including special extinguishing equipment, such asthat using foam, inert gas, or dry chemicals), spillcontrol equipment
4,and decontamination equipment; and
D) Water at adequate volume and pressure to supply waterhose streams, or foam producing equipment, orautomatic sprinklers, or water spray systems.
3) Testing and maintenance of equipment. All facilitycommunications or alarm systems, fire protection equipment,spill control equipment, and decontamination equipment,where required, must be tested and maintained as necessaryto assure its proper operation in time of emergency.
101
4) Access to communications or alarm system.
A) Whenever used oil is being poured, mixed, spread, orotherwise handled, all personnel involved in theoperation must have immediate access to an internalalarm or emergency communication device, eitherdirectly or through visual or voice contact withanother employee, unless such a device is not requiredin subsection (a)(2) of this Section.
B) If there is ever just one employee on the premiseswhile the facility is operating, the employee musthave immediate access to a device, such as a telephone(immediately available at the scene of operation) or ahand—held two—way radio, capable of summoning externalemergency assistance, unless such a device is notrequired in subsection (a)(2) of this. Section.
5) Required aisle space. The owner or operator shall maintainaisle space to allow the unobstructed movement of personnel,fire protection equipment, spill control equipment, anddecontamination equipment to any area of facility operationin an emergency, unless aisle space is not needed for any ofthese purposes.
6) Arrangements with local authorities.
A) The owner or operator shall attempt to make thefollowing arrangements, as appropriate for the type ofused oil handled at the facility and the potentialneed for the services of these organizations:
i) Arrangements to familiarize police, firedepartments, and emergency response teams withthe layout of the facility, properties of usedoil handled at the facility and associatedhazards, places where facility personnel wouldnormally be working, entrances to roads insidethe facility, and possible evacuation routes;
ii) Where more than one police and fire departmentmight respond to an emergency, agreementsdesignating primary emergency authority to aspecific police and a specific fire department,and agreements with any others to providesupport to the primary emergency authority;
iii) Agreements with State emergency response teams,emergency response contractors, and equipmentsuppliers; and
iv) Arrangements to familiarize local hospitals withthe properties of used oil handled at thefacility and the types of injuries or illnesseswhich could result from fires, explosions, orreleases at the facility.
B) Where State or local authorities decline to enter intosuch arrangements, the owner or operator shalldocument the refusal in the operating record.
b) Contingency plan and emergency procedures. Owners and operators
102
of used oil processors and re—refiners facilities shall complywith the following requirements:
1) Purpose and implementation of contingency plan.
A) Each owner or operator shall have a contingency planfor the facility. The contingency plan must bedesigned to minimize hazards to human health or theenvironment from fires, explosions, or any unplannedsudden or non—sudden release of used oil to air, soil,or surface water.
B) The provisions of the plan must be carried outimmediately whenever there is a fire, explosion, orrelease o~ used oil which could threaten human healthor the environment.
2) Content of contingency plan.
A) The contingency plan must describe the actionsfacility personnel muotshall take to comply withsubsections (b)(1) and (b)(6) of this Section inresponse to fires, explosions, or any unplanned suddenor non—sudden release of used oil to air, soil, orsurface water at the facility.
B) If the owner or operator has already prepared a SpillPrevention7- Control.,. and Countermeasures (SPCC) Planin accordance with 40 CFR 112, or 40 CFR 15lO~QQ, orsome other emergency or contingency plan, the owner oroperator need only amend that plan to incorporate usedoil management provisions that are sufficient tocomply with the requirements of this Part.
C) The plan must describe arrangements agreed to by localpolice departments, fire departments, hospitals,contractors, and State and local emergency responseteams to coordinate emergency services, pursuant tosubsection (a)(6) of this Section.
D) The plan must list names, addresses, and phone numbers(office and home) of all persons qualified to act asemergency coordinator (see subsection (b)(5) of thisSection), and this list must be kept up to date.Where more than one person is listed, one must benamed as primary emergency coordinator and others mustbe listed in the order in which they will assumeresponsibility as alternates.
E) The plan must include a list of all emergencyequipment at the facility (such as fire extinguishingsystems, spill control equipment, communications andalarm systems (internal and external), anddecontamination equipment), where this equipment isrequired. This list must be kept up to date. Inaddition, the plan must include the location and aphysical description of each item on the list, and abrief outline of its capabilities.
F) The plan must include an evacuation plan for facilitypersonnel where there is a possibility that evacuationcould be necessary. This plan must describe signal(s)
103
to be used to begin evacuation, evacuation routes, andalternate evacuation routes (in cases where theprimary routes could be blocked by releases of usedoil or fires).
3) Copies of contingency plan. A copy of the contingency planand all revisions to the plan must be:
A) Maintained at the facility; and
B) Submitted to all local police departments, firedepartments, hospitals, and State and local emergencyresponse teams that may be called upon to provideemergency services.
4) Amendment of contingency plan. The contingency plan must be
reviewed, and immediately amended, if necessary, whenever:
A) Applicable regulations are revised;
B) The plan fails in an emergency;
C) The facility changes—in its design, construction,operation, maintenance, or other circumstances—in away that materially increases the potential for fires,explosions, or releases of used oil, or changes theresponse necessary in an emergency;
D) The list of emergency coordinators changes; or
E) The list of emergency equipment changes.
5) Emergency coordinator. At all times, there must be at leastone employee either on the facility premises or on call(i.e., available to respond to an emergency by reachi.ng thefacility within a short period of time) with theresponsibility for coordinating all emergency responsemeasures. This emergency coordinator shall be thoroughlyfamiliar with all aspects of the facility’s contingencyplan, all operations and activities at the facility, thelocation and characteristic of used oil handled, thelocation of all records within the facility, and facilitylayout. In addition, this person must have the authority tocommit the resources needed to carry out the contingencyplan.
BOARD NOTE: U.S. EPA cited the following as guidance: Theemergency coordinator’s responsibilities are more fullyspelled out in subsection (b)(6) below. Applicableresponsibilities for the emergency coordinator vary,depending on factors such as type and variety of used oilhandled by the facility, and type and complexity of thefacility.
6) Emergency procedures.
A) Whenever there is an imminent or actual emergencysituation, the emergency coordinator (or the designeewhen the emergency coordinator is on call) shallimmediately:
i) Activate internal facility alarms or
104
communication systems, where applicable, tonotify all facility personnel; and
ii) Notify appropriate State or local agencies withdesignated response roles if their help isneeded.
B) Whenever there is a release, fire, or explosion, theemergency coordinator shall immediately identify thecharacter, exact source, amount, and a real extent ofany released materials. He or she may do this byobservation or review of facility records of manifestsand, if necessary, by chemical analysts.
C) Concurrently, the emergency coordinator shall assesspossible hazards to human health or the environmentthat may result from the release, fire, or explosion.This assessment must consider both direct and indirecteffects of the release, fire, or explosion (e.g., theeffects of any toxic, irritating, or asphyxiatinggases that are generated, or the effects of anyhazardous surface water run—of fs from water ofchemical agents used to control fire and heat—inducedexplosions).
D) If the emergency coordinator determines that thefacility has had a release, fire, or explosion whichcould threaten human health, or the environment,outside the facility, he or she shall report hiafindings as follows:
i) If his assessment indicated that evacuation oflocal areas may be advisable, he or she shallimmediately notify appropriate localauthorities. He or she shall be available tohelp appropriate officials decide whether localareas should be evacuated; and
ii) He shall immediately notify either thegovernment official designated as the on—scenecoordinator for the geographical area (in theapplicable regional contingency plan under 40CFR 1510aQQ), or the National Response Center(using their 24—hour toll free number (800) 424—8802). The report must include: Name andtelephone number of reporter; Name and addressof facility; Time and type of incident (e.g.,release, fire); Name and quantity of material(s)involved, to the extent known; The extent ofinjuries, if any; and c~he possible hazards tohuman health, or the environment, outside thefacility.
E) During an emergency, the emergency coordinator Ethalltake all reasonable measures necessary to ensurE! thatfires, explosions, and releases do not occur, recur,or spread to other used oil or hazardous waste at thefacility. These measures must include, whereapplicable, stopping processes and operation,collecting and containing released used oil, andremoving or isolating containers.
105
F) If the facility stops operation in response to a fire,explosion, or release, the emergency coordinator shallmonitor for leaks, pressure buildup, gas generation,or ruptures in valves, pipes, or other equipment,wherever this is appropriate.
G) Immediately after an emergency, the emergencycoordinator shall provide for recycling, storing, ordisposing of recovered used oil, contaminated soil or -
surface water, or any other material that results froma release, fire, or explosion at the facility.
H) The emergency coordinator shall ensure that, in theaffected area(s) of the facility:
i) No waste or used oil that may be incompatiblewith the released material is recycled, treated,stored, or disposed of until cleanup proceduresare completed; and
ii) All emergency equipment listed in thecontingency plan is cleaned and fit for itsintended use before operations are resumed.
iii) The owner or operator shall notify the t4%eAgency, and all other appropriate State andlocal authorities that the facility is incompliance with subsections (b)(6)(H)(i) and(b)(6)(H)(ii) of this Section before operationsare resumed in the affected area(s) of thefacility.
I) The owner or operator shall note in the operatingrecord the time, date4, and details of any incidentthat requires implementing the contingency plan.Within 15 days after the incident, 4~ej~, shall submit awritten report on the incident to the RegionalAdministrator. The report must include:
i) The name, address, and telephone number of theowner or operator;
ii) The name, address, and telephone number of thefacility;
iii) The date, time, and type of incident (e.g.,
fire, explosion);
iv) The name and quantity of material(s) involved;
v) The extent of injuries, if any;
vi) An assessment of actual or potential hazards tohuman health or the environment, where this isapplicable; and
vii) The estimated quantity and disposition ofrecovered material that resulted from theincident,
(Source: Amended at Ill. Reg. _________, effective
106
Section 739.153 Rebuttable presumption for used oil
a) To ensure that used oil is not a hazardous waste under therebuttable presumption of Section 739.llO(b)(1)(ii), the owner oroperator of a used oil processing facility muatshall determinewhether the total halogen content of used oil managed at thefacility is above or below 1,000 ppm.
b) The owner or operator mu-s-tshall make this determination by:
1) Testing the used oil; or
2) Applying knowledge of the halogen content of the used oil in
light of the materials or processes used.
c) If the used oil contains greater than or equal to 1,000 ppm totalhalogens, it is presumed to be a hazardous waste because it hasbeen mixed with halogenated hazardous waste listed in 35 Ill. Adm.Code 721.Subpart D. The owner or operator may rebut thepresumption by demonstrating that the used oil does not containhazardous waste (for example, by using an analytical method fromSW—846, Edition III, to show that the used oil does not containsignificant concentrations of halogenated hazardous constituentslisted in 35 Ill. Adni. Code 721.Appendix H). U.S. EPA PublicationSW—846, Third Edition, is available for the coot of ~110.0O fromthe Government Printing Office, Superintendent of Documents, P0Box 371954, Pittsburgh, PA 15250—7954. (202) 783—3238 (documentnumber 955—001—00000—1).
1) The rebuttable presumption does not apply to metalworkingoils and fluids containing chlorinated paraffins, if theyare processed, through a tolling arrangement as described inSection 739.124(c), to reclaim metalworking oils and fluids.The presumption does apply to metalworking oils and fluidsif such oils and fluids are recycled in any other manner, ordisposed.
2) The rebuttable presumption does not apply to used oilscontaminated with chlorofluorocarbons (CFC5) removed fromrefrigeration units if the CFC are destined for reclamation.The rebuttable presumption does apply to used oilscontaminated with CFCs that have been mixed with used oilfrom sources other than refrigeration units.
(Source: Amended at Ill. Reg. ________, effective
SUBPART G: STANDARDSFOR USED OIL BURNERSTHAT BURN
OFF—SPECIFICATION USED OIL FOR ENERGYRECOVERY
Section 739.163 Rebuttable presumption for used oil
a) To ensure that used oil managed at a used oil burner facility isnot hazardous waste under the rebuttable presumption of Section739.110(b) (1) (ii), a used oil burner muctshall determine whetherthe total halogen content of used oil managed at the facility isabove or below 1,000 ppm.
b) The used oil burner muctshall determine if the used oil containsabove or below 1,000 ppm total halogens by:
107
1) Testing the used oil;
2) Applying knowledge of the halogen content of the used oil inlight of the materials or processes used; or
3) If the used oil has been received from a processor subjectto regulation under Subpart F of this Part, usinginformation provided by the processor.
c) If the used oil contains greater than or equal to 1,000 ppm totalhalogens, it is presumed to be a hazardous waste because it hasbeen mixed with halogenated hazardous waste listed in 35 Ill. Adin.Code 721.Subpart D. The owner or operator may rebut thepresumption by demonstrating that the used oil does not containhazardous waste (for example, by using an analytical method fromSW—846, Edition III, to show that the used oil does not containsignificant concentrations of halogenated hazardous constituentslisted in 35 Ill. Adm. Code 721.Appendix H). U.S. EPA PublicationSW—846, Third Edition, is available for the coot—of —$110.00 fromthe Government Printing Office, Superintendent of Documents, P0Box 371954, Pittsburgh, PA 15250—7954. 202—783—3238 (documentnumber 955—001-00000—1).
1) The rebuttable presumption does not apply to metalworkingoils or fluids containing chlorinated paraff ins, if they areprocessed, through a tolling arrangement as described inSection 739.124(c), to reclaim metalworking oils or fluids.The presumption does apply to metalworking oils or fluids ifsuch oils and fluids are recycled in any other manner, ordisposed.
2) The rebuttable presumption does not apply to used oilscontaminated with chiorofluorocarbons (CFCs) removed fromrefrigeration units where the CFCs are destined forreclamation. The rebuttable presumption does apply to usedoils contaminated with CFC8 that have been mixed with usedoil from sources other than refrigeration units.
d) Record retention. Records of analyses conducted or informationused to comply with subsections (a), (b), and (c) above must bemaintained by the burner for at least 3 years.
(Source: Amended at Ill. Reg. _________, effective
SUBPART H: STANDARDSFOR USED OIL FUEL MARKETERS
Section 739.171 Prohibitions
A used oil fuel marketer may initiate a shipment of off—specification used oil
only to a used oil burner that:
a) Has a~U.S. EPA identification number and Illinois special waste
identification number; and
b) Burns the used oil in an industrial furnace or boiler identified
in Section 739.161(a).
(Source: Amended at Ill. Reg. _________, effective
