LXP200 and Elastix Server Setup Guide...LXP200 and Elastix Server Setup Guide 7 MANUAL CONFIGURATION...

http://www.elastix.org

LXP200 and Elastix Server

Setup Guide

PaloSanto Solutions LXP200 and Elastix Server Setup Guide

2

1.0 Setup Diagram

Figure 1-1 is a setup diagram for a single IP phone Elastix LXP200 configuration. The

phone is setup as a SIP telephony device.

Figure 1-1. Setup Diagram

2.0 Host PC Environment

Table 2-1. Host Server Environment Details

Description

Hardware Type Elastix Appliance ELX-Series

Hardware Version ELX-3000

Software Type Elastix

Software Version 2.3

3.0 Test Setup Equipment

Table 3-1. Test Setup Equipment

Equipment Model Version

Video Call IP (SIP) Phone N/A N/A

Palosanto Solutions Elastix LXP200 1.0.4.21

Switch N/A N/A


3

4.0 Setup Procedure

To set up the Elastix Server for the Elastix LXP200

1. Go to the web address of the Elastix Server Login page. The web address is

determined by the customer, for this guide we have used the IP address

192.168.1.75

2. On the Login page, type the username and password for an administrative user into

the Username and Password fields, see Figure 4-1. The username and password are

determined by the customer.

Figure 4-1. Login

3. Press Enter or click on the Submit button to go to Elastix‟s Dashboard

4. Once inside, click on the PBX tab on the menu at the top of the screen

Figure 4-2. Dashboard


4

5. Click on the Submit button to add an extension, see Figure 4-3. This will take you

to the Add SIP Extension page.

Figure 4-3. Add an Extension

6. On the Add SIP Extension page (Figure 4-4), fill in the following information:

• User Extension (301 in this example)

• Display Name („LXP200Phone‟ in this example)

• secret („h7Dka3Rf9si0t‟ in this example)

Figure 4-4. Add SIP Extension

7. Click on “Submit” button at the end of the page, and you will see a similar page on

Figure 4-5 displaying the “Apply Configuration Changes Here” pink ribbon on top

of the screen. Click on there to apply changes.


5

Figure 4-5

8. With this you have just finished creating a SIP extension that will be used by the

Elastix LXP200 to register with the Elastix Server. Repeat Steps 5 through 7 to

similarly create another extension (different values on Step 6) to be used by the IP

(SIP) Phone to register as well (extension 302 in this example). Once you finished

you will see something similar to Figure 4-6.

Figure 4-6

9. You will need to enter the information from the extension created on the Elastix

Server into the LXP200 Phone. Connect the LXP200 phone to the same network

than Elastix Server.

The default values configured on the phone are:

Factory default settings

IP Addressing DHCP

Web Access Password admin

When the phone obtains an IP Address from your DHCP server, it is shown on the

main screen of the phone. If you don‟t have a DHCP server and you want to set

static IP addressing you must do the following:

From the phone, press Menu => Network => IP Setting => Static IP.

Menu button is the one which is located in the middle of the arrow buttons.


6

Now set the values for connecting to the network. When you finish, select Back

option and you will be asked for rebooting. Select YES.

To register the Elastix Phone there are two methods: Manual Configuration and

AutoProvisioning using Elastix’s Endpoint Configurator.


7

MANUAL CONFIGURATION

1. Log in to the Elastix LXP200 WebUI by pointing your browser to the Elastix

Phone‟s IP address.

2. When prompted, enter the Web Access Password to accesss to the WebUI (Figure

4-7).

Figure 4-7 Elastix Phone WebUI

3. Use the information from the Add SIP Extension page (Figure 4-4) to enter the

following necessary information on “Accounts => Account 1” section of the

LXP200 Phone WebUI (Figure 4-8):

Account Active: Yes

Account Name: ElastixPhone

SIP Server: Elastix Server‟s IP Address (192.168.1.75 in this example)

SIP User ID: 301

Authenticate ID: 301

Authenticate Password: („h7Dka3Rf9si0t‟ in this example)


8

Figure 4-8. Account

4. Once you have entered the required information, click on „Update‟ button located at

the end of the page.

5. To check the correct registration of the phone, go to “Status” section. You should

see your phone registered (Figure 4-9). If the phone is not registered, make sure

you‟ve entered the correct information.

Figure 4-9. Status

6. Configure the other IP (SIP) Phone with the correct parameters.

7. To test the Elastix LXP200, pick up the previously configured IP (SIP) Phone and

call the LXP200‟s extension number (301 in this example). When the call is

established, speak into the phone and verify that the other IP (SIP) Phone can hear

your voice. Check this by calling from both ends. This step completes the manual

procedure.


9

AUTOPROVISIONING USING ELASTIX‟S ENDPOINT

CONFIGURATOR

Note: The support for Endpoint Configurator is available in Elastix 2.4 by installing the

new Endopoint configurator module. This new module is already included in Elastix

2.5.

1. For Elastix 2.4, log in to the console and install the module by entering the

command:

yum -y install elastix-endpointconfig2

2. After installation, in the Elastix Web Interface go to “PBX => Batch Configurations

=> New Endpoint Configurator”. See figure 4-10

Figure 4-10. New Endpoint Configurator

3. Type the network address where the phone is located and click on the magnifying

glass. This will generate a list with all the phones available in that network. See

figure 4-11.

Figure 4-11. List of endpoints

4. In the row where the phone you want to autoprovision is located (find it according

to either its MAC or IP Address):

Mark the checkbox

From the drop-down list, select the correct Phone Model if it is not detected

automatically

Click on the link “[Configure x.x.x.x]” to set the parameters to configure the

phone.


10

5. After clicking in the configuration link, you will see a window with many tabs

according to what you want to configure. In this case we will configure a SIP

account. Go to the tab “Accounts” and drag the accounts you want to assign from

left to right. Then click on Apply button. See figure 4-12.

Figure 4-12. Accounts configuration

6. After configuring you will see that the status field of the phone has changed. See

figure 4-13

Figure 4-13. List of endpoints

7. Now with the phones selected, click on the button “Apply Configuration” located

next to the magnifying glass button. A message will be shown saying the operation

was successful. See figure 4-14.


11

Figure 4-14. Configuration successful

8. Your phone will reboot, and when it boots up it should be registered with Elastix

with the accounts you set. This step completes the procedure.

LXP200 and Elastix Server Setup Guide...LXP200 and Elastix Server Setup Guide 7 MANUAL CONFIGURATION...

Documents

Transcript of LXP200 and Elastix Server Setup Guide...LXP200 and Elastix Server Setup Guide 7 MANUAL CONFIGURATION...