LTE Principle
-
Upload
rendra-hakim -
Category
Documents
-
view
59 -
download
13
description
Transcript of LTE Principle
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved.
LTELong Term Evolution
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 2
Mobile communication system evolution
1G (First Generation)
2G (Second Generation)
3G (Third Generation)
4G (Fourth Generation)
AMPS
TACS
ETACS
Advanced Mobile Telephone System
Total Access Communications System
Extended Total Access Communication System
GSM
CDMA One (IS-95)
DAMPS ( IS-136)
Global System for Mobile communications
Code Division Multiple Access Based on IS-95
Digital - Advanced Mobile Phone System Based onIS-136Other
UMTSWCDMA
TD-SCDMA
CDMA2000
WiMAX
LTE Advanced
UMBEV-DO Rev C
WiMAX802.16m
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 3
201120102009200820072006200520042003200220012000
R99 R4 R5 R6 R7 R8 R9 R10U
MT
S
HS
PA
DL
HS
PA
UL
LT
E
LT
E
Ad
v
HS
PA
+
EP
C
Co
mm
on
IMS
IMS
MM
Te
l
3GPP Time Line and Evolution
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 4
IMT Advanced RequirementsSpecific requirements of the IMT-Advanced report included: All-IP packet switched network and Interoperability with existing wireless standards. Share and use the network resources to support more simultaneous users per cell Scalable channel bandwidth 5–20 MHz, optionally up to 40 MHz Seamless connectivity and global roaming across multiple networks (smooth handovers). 1 Gbit/s in the downlink should be possible over less than 67 MHz bandwidth Data rate :
100 Mbit/s (high speeds)1 Gbit/s (fixed positions).
Peak link spectral efficiency :15 bit/s/Hz (downlink) 6.75 bit/s/Hz (uplink)
In the downlink spectral efficiency up to :3 bit/s/Hz/cell (outdoor)2.25 bit/s/Hz/cell (indoor)
14
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 5
LTE Background Introduction• What is LTE ?
LTE (Long Term Evolution) is known as the evolution of radio access technology conducted by 3GPP.
The radio access network will evolve to E-UTRAN (Evolved UMTS Terrestrial Radio Access Network), and the
correlated core network will evolved to SAE (System Architecture Evolution).
What can LTE do ? Flexible bandwidth configuration: supporting 1.4MHz,
3MHz, 5MHz, 10Mhz, 15Mhz and 20MHz
Peak date rate (within 20MHz bandwidth): 100Mbps for
downlink and 50Mbps for uplink
Time delay: <100ms (control plane), <5ms (user plane)
Provide 100kbps data rate for mobile user (up to 350kmph)
Support eMBMS
Circuit services is implemented in PS domain: VoIP
Lower cost due to simple system structure
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 6
LTE Network Architecture• Main Network Element of LTE
The E-UTRAN consists of e-NodeBs, providing the user plane and control plane. The EPC consists of MME, S-GW and P-GW.
Compare with traditional 3G network, LTE architecture becomes much more simple and flat, which can lead to lower networking cost, higher networking flexibility and shorter time delay of user data and control signaling.
Network Interface of LTE The e-NodeBs are interconnected with each other by means of the X2 interface, which enabling direct transmission of
data and signaling. S1 is the interface between e-NodeBs and the EPC, more specifically to the MME via the S1-MME and to the S-GW via
the S1-U
eNB
MME / S-GW MME / S-GW
eNB
eNB
S1 S1
X2 E-UTRAN
UMTS LTE
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 7
Page 7
• SAE Brief Introduction SAE ( System Architecture Evolution ) considers evolution for the whole system architecture, including :
Flat Functionality. Take out the RNC entity and part of the functions are arranged on e-NodeB in order to reduce the latency and enhance the schedule ability, such as interference coordination, internal load balance, etc.
Part of the functions are arranged on core network. To enhance the mobility management, all IP technology is applied, user-plane and control-plane are separated. The compatibility of other RAT is considered.
SGi
S4
S3 S1-MME
PCRF S7
S6a
HSS
Operator ’ s IP Services (e.g. IMS, PSS etc.)
Rx+ S10
UE
GERAN
UTRAN SGSN
“ LTE - Uu ” EUTRAN
MME
S11
S5 Serving SAE
Gateway
PDN SAE
Gateway S1-U
SAE
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 8
FDMA TDMA CDMA and OFDMA
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 9
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 10
Page 10
Introduction OFDM ( Orthogonal Frequency Division Multiplexing ) is a modulation
multiplexing scheme. The system bandwidth is divided into a plurality of
orthogonal.
Orthogonality of different subcarriers is achieved by the baseband IFFT.
OFDM OFDM has many advantages that can meet the needs of E-
UTRAN, which is one of B3G and 4G key technology.
OFDM is a modulation multiplexing scheme, and the
corresponding multi-access techniques is OFDMA. OFDMA are
used in LTE downlink.
For LTE uplink the multiple access scheme is SC-FDMA .
OFDM
…
Sub-carriersFFT
Time
Symbols
System Bandwidth
Guard
Intervals
…
Frequency
…
Sub-carriersFFT
Time
Symbols
System Bandwidth
Guard
Intervals
…
Frequency
OFDM 与 OFDMA 的比较
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 11
OFDMA and SC-FDMA Block Diagram
29
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 12
Cyclic Prefix
CPNormal
5,2 µs first symbol
4,7 µs other symbol
Extended 16,7 µs
ISI (Inter Symbol Interference)
COPY and insert
24
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 13
Page 13
OFDM & OFDMA OFDM (Orthogonal Frequency Division Multiplexing) is a
modulation multiplexing technology, divides the system bandwidth into orthogonal subcarriers. CP is inserted between the OFDM symbols to avoid the ISI.
OFDMA is the multi-access technology related with OFDM, is used in the LTE downlink. OFDMA is the combination of TDMA and FDMA essentially.
Advantage: High spectrum utilization efficiency due to orthogonal subcarriers need no protect bandwidth. Support frequency link auto adaptation and scheduling. Easy to combine with MIMO.
Disadvantage: Strict requirement of time-frequency domain synchronization. High PAPR.
DFT-S-OFDM & SC-FDMA DFT-S-OFDM (Discrete Fourier Transform Spread OFDM)
is the modulation multiplexing technology used in the LTE uplink, which is similar with OFDM but can release the UE PA limitation caused by high PAPR. Each user is assigned part of the system bandwidth.
SC-FDMA ( Single Carrier Frequency Division Multiple Accessing ) is the multi-access technology related with DFT-S-OFDM.
Advantage: High spectrum utilization efficiency due to orthogonal user bandwidth need no protect bandwidth. Low PAPR.
The subcarrier assignment scheme includes Localized mode and Distributed mode.
OFDMA & SC-FDMA
User 1
User 2
User 3
Sub-carriers
TTI: 1ms
Frequency
System Bandwidth
Sub-band:12Sub-carriersTime
User 1
User 2
User 3
User 1
User 2
User 3
Sub-carriers
TTI: 1ms
Frequency
System Bandwidth
Sub-band:12Sub-carriersTime
Sub-carriers
TTI: 1ms
Frequency
Time
System Bandwidth
Sub-band:12Sub-carriers
User 1
User 2
User 3
Sub-carriers
TTI: 1ms
Frequency
Time
System Bandwidth
Sub-band:12Sub-carriers
User 1
User 2
User 3
User 1
User 2
User 3
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 14
Frequency Band of LTE
E-UTRA Band
Uplink (UL) Downlink (DL)Duplex ModeFUL_low – FUL_high FDL_low – FDL_high
1 1920 MHz – 1980 MHz 2110 MHz – 2170 MHz FDD
2 1850 MHz – 1910 MHz 1930 MHz – 1990 MHz FDD
3 1710 MHz – 1785 MHz 1805 MHz – 1880 MHz FDD
4 1710 MHz – 1755 MHz 2110 MHz – 2155 MHz FDD
5 824 MHz – 849 MHz 869 MHz – 894MHz FDD
6 830 MHz – 840 MHz 875 MHz – 885 MHz FDD
7 2500 MHz – 2570 MHz 2620 MHz – 2690 MHz FDD
8 880 MHz – 915 MHz 925 MHz – 960 MHz FDD
9 1749.9 MHz–
1784.9 MHz 1844.9 MHz –
1879.9 MHzFDD
10 1710 MHz – 1770 MHz 2110 MHz – 2170 MHz FDD
111427.9 MHz – 1452.9 MHz 1475.9 MHz – 1500.9 MHz FDD
12 698 MHz – 716 MHz 728 MHz – 746 MHz FDD
13 777 MHz – 787 MHz 746 MHz – 756 MHz FDD
14 788 MHz – 798 MHz 758 MHz – 768 MHz FDD
… … … …
17 704 MHz – 716 MHz 734 MHz – 746 MHz FDD
... … … …
E-UTRA Band
Uplink (UL) Downlink (DL)Duplex ModeFUL_low – FUL_high FDL_low – FDL_high
33 1900 MHz – 1920 MHz 1900 MHz – 1920 MHz TDD
34 2010 MHz – 2025 MHz 2010 MHz – 2025 MHz TDD
35 1850 MHz – 1910 MHz 1850 MHz – 1910 MHz TDD
36 1930 MHz – 1990 MHz 1930 MHz – 1990 MHz TDD
37 1910 MHz – 1930 MHz 1910 MHz – 1930 MHz TDD
38 2570 MHz – 2620 MHz 2570 MHz – 2620 MHz TDD
39 1880 MHz – 1920 MHz 1880 MHz – 1920 MHz TDD
40 2300 MHz – 2400 MHz 2300 MHz – 2400 MHz TDD
TDD Frequency Band
FDD Frequency Band
From LTE Protocol: Duplex mode: FDD and TDD
Support frequency band form 700MHz to 2.6GHz
Support various bandwidth: 1.4MHz, 3MHz, 5MHz,
10MHz, 15MHz, 20MHz
Protocol is being updated, frequency information could be
changed.
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 15
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 16
Carrier Frequency EARFCN Calculation
eNB
UE
FDL = FDL_low + 0.1(NDL - NOffs-DL)
FUL = FUL_low + 0.1(NUL - NOffs-UL)
The values of FDL_low , NDL , NOffs-DL can be found from 3GPP 36.101, as below :
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 17
Page 17
Radio Frame Structures Supported by LTE:
Type 1, applicable to FDD
Type 2, applicable to TDD
FDD Radio Frame Structure:
LTE applies OFDM technology, with subcarrier spacing f=15kHz and 2048-order IFFT. The time unit in
frame structure is Ts=1/(2048* 15000) second
FDD radio frame is 10ms shown as below, divided into 20 slots which are 0.5ms. One slot consists of 7
consecutive OFDM Symbols under Normal CP configuration
#0 #1 #2 #3 #19#18
One radio frame, Tf = 307200Ts = 10 ms
One slot, Tslot = 15360Ts = 0.5 ms
One subframe FDD Radio Frame Structure
Concept of Resource Block: LTE consists of time domain and frequency domain resources. The minimum unit for schedule is RB
(Resource Block), which compose of RE (Resource Element)
RE has 2-dimension structure: symbol of time domain and subcarrier of frequency domain
One RB consists of 1 slot and 12 consecutive subcarriers under Normal CP configuration
Radio Frame Structure (1)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 18
Resource Block
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 19
Page 19
• TDD Radio Frame Structure:
Applies OFDM, same subcarriers spacing and time
unit with FDD.
Similar frame structure with FDD. radio frame is
10ms shown as below, divided into 20 slots which
are 0.5ms.
The uplink-downlink configuration of 10ms frame are
shown in the right table.
One slot, Tslot=15360Ts
GP UpPTSDwPTS
One radio frame, Tf = 307200Ts = 10 ms
One half-frame, 153600Ts = 5 ms
30720Ts
One subframe, 30720Ts
GP UpPTSDwPTS
Subframe #2 Subframe #3 Subframe #4Subframe #0 Subframe #5 Subframe #7 Subframe #8 Subframe #9
Uplink-downlink Configurations
Uplink-downlink configuration
Downlink-to-Uplink Switch-point periodicity
Subframe number
0 1 2 3 4 5 6 7 8 9
0 5 ms D S U U U D S U U U
1 5 ms D S U U D D S U U D
2 5 ms D S U D D D S U D D
3 10 ms D S U U U D D D D D
4 10 ms D S U U D D D D D D
5 10 ms D S U D D D D D D D
6 5 ms D S U U U D S U U D
DwPTS: Downlink Pilot Time Slot
GP: Guard Period
UpPTS: Uplink Pilot Time Slot
TDD Radio Frame Structure
D: Downlink subframe
U: Uplink subframe
S: Special subframe
Radio Frame Structure (2)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 20
Page 20
• Special Subrame Structure: Special Subframe consists of DwPTS, GP and UpPTS . 9 types of Special subframe configuration. Guard Period size determines the maximal cell radius.
(100km) DwPTS consists of at least 3 OFDM symbols, carrying
RS, control message and data. UpPTS consists of at least 1 OFDM symbol, carrying
sounding RS or short RACH.
Configuration of special subframe
Special Subframe Structure
Special subframe configuration
Normal cyclic prefix
DwPTS GP UpPTS
0 3 10
1
1 9 4
2 10 3
3 11 2
4 12 1
5 3 9
26 9 3
7 10 2
8 11 1
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 21
Page 21
Radio Frame Structure (3)• CP Length Configuration:
Cyclic Prefix is applied to eliminate ISI of
OFDM.
CP length is related with coverage radius.
Normal CP can fulfill the requirement of
common scenarios. Extended CP is for wide
coverage scenario.
Longer CP, higher overheading.
Configuration DL OFDM CP LengthUL SC-FDMA CP
LengthSub-carrier of
each RBSymbol of each slot
Normal CP f=15kHz160 for slot #0
144 for slot #1~#6
160 for slot #0
144 for slot #1~#6 127
Extended CP
f=15kHz 512 for slot #0~#5 512 for slot #0~#5 6
f=7.5kHz 1024 for slot #0~#2 NULL 24 (DL only) 3 (DL only)
CP Configuration
Slot structure under Normal CP configuration
( f=15kHz)△
Slot structure under Extended CP configuration
( f=15kHz)△
Slot structure under Extended CP configuration
( f=7.5kHz)△
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 22
Page 22
Brief Introduction of Physical Channels
Downlink Channels : Physical Broadcast Channel (PBCH): Carries system information for cell
search, such as cell ID.
Physical Downlink Control Channel (PDCCH) : Carries the resource allocation
of PCH and DL-SCH, and Hybrid ARQ information.
Physical Downlink Shared Channel (PDSCH) : Carries the downlink user data.
Physical Control Format Indicator Channel (PCFICH) : Carriers information of
the OFDM symbols number used for the PDCCH.
Physical Hybrid ARQ Indicator Channel (PHICH) : Carries Hybrid ARQ
ACK/NACK in response to uplink transmissions.
Physical Multicast Channel (PMCH) : Carries the multicast information.
Uplink Channels : Physical Random Access Channel (PRACH) : Carries the random access
preamble.
Physical Uplink Shared Channel (PUSCH) : Carries the uplink user data.
Physical Uplink Control Channel (PUCCH) : Carries the HARQ ACK/NACK,
Scheduling Request (SR) and Channel Quality Indicator (CQI), etc.
BCH PCH DL-SCHMCH
DownlinkPhysical channels
DownlinkTransport channels
PBCH PDSCHPMCH PDCCH
UplinkPhysical channels
UplinkTransport channels
UL-SCH
PUSCH
RACH
PUCCHPRACH
Mapping between downlink transport channels and downlink physical channels
Mapping between uplink transport channels and downlink physical channels
Physical Layer
MAC Layer
Physical Layer
MAC Layer
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 23
Page 23
Downlink Physical Channel
ScramblingModulation
mapper
Layermapper
Precoding
Resource element mapper
OFDM signal generation
Resource element mapper
OFDM signal generation
ScramblingModulation
mapper
layers antenna portscode words
Downlink Physical Channel Processing scrambling of coded bits in each of the code words to be transmitted on a physical channel modulation of scrambled bits to generate complex-valued modulation symbols mapping of the complex-valued modulation symbols onto one or several transmission layers precoding of the complex-valued modulation symbols on each layer for transmission on the antenna ports mapping of complex-valued modulation symbols for each antenna port to resource elements generation of complex-valued time-domain OFDM signal for each antenna port
Modulation Scheme of Downlink Channel
Shown at the right table
Phy Ch Modulation Scheme Phy Ch Modulation Scheme
PBCH QPSK PCFICH QPSK
PDCCH QPSK PHICH BPSK
PDSCH QPSK, 16QAM, 64QAM PMCH QPSK, 16QAM, 64QAM
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 24
Page 24
Uplink Physical ChannelUplink Physical Channel Processing
scrambling modulation of scrambled bits to generate complex-valued symbols transform precoding to generate complex-valued symbols mapping of complex-valued symbols to resource elements generation of complex-valued time-domain SC-FDMA signal for each antenna port
Modulation Scheme of Downlink Channel Shown at the right table
Phy Ch Modulation Scheme
PUCCH BPSK, QPSK
PUSCH QPSK, 16QAM, 64QAM
PRACH Zadoff-Chu
ScramblingModulation
mapperTransform precoder
Resource element mapper
SC-FDMA signal gen.
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 25
Page 25
0l
0R
0R
0R
0R
6l 0l
0R
0R
0R
0R
6l
One
ant
enna
por
tTw
o an
tenn
a po
rts
Resource element (k,l)
Not used for transmission on this antenna port
Reference symbols on this antenna port
0l
0R
0R
0R
0R
6l 0l
0R
0R
0R
0R
6l 0l
1R
1R
1R
1R
6l 0l
1R
1R
1R
1R
6l
0l
0R
0R
0R
0R
6l 0l
0R
0R
0R
0R
6l 0l
1R
1R
1R
1R
6l 0l
1R
1R
1R
1R
6l
Four
ant
enna
por
ts
0l 6l 0l
2R
6l 0l 6l 0l 6l
2R
2R
2R
3R
3R
3R
3R
even-numbered slots odd-numbered slots
Antenna port 0
even-numbered slots odd-numbered slots
Antenna port 1
even-numbered slots odd-numbered slots
Antenna port 2
even-numbered slots odd-numbered slots
Antenna port 3
Downlink Physical Signals (1)Downlink RS (Reference Signal):
Similar with Pilot signal of CDMA. Used for downlink physical channel demodulation
and channel quality measurement (CQI)
Three types of RS in protocol. Cell-Specific Reference Signal is essential and the other
two types RS (MBSFN Specific RS & UE-Specific RS) are optional.
Cell-Specific RS Mapping in Time-
Frequency DomainOn
e A
nte
nn
a
Po
rtTw
o A
nte
nn
a
Po
rts
Fo
ur
An
ten
na
P
ort
s
Antenna Port 0 Antenna Port 1 Antenna Port 2 Antenna Port 3
Characteristics: Cell-Specific Reference Signals are generated from cell-specific RS
sequence and frequency shift mapping. RS is the pseudo-random
sequence transmits in the time-frequency domain.
The frequency interval of RS is 6 subcarriers.
RS distributes discretely in the time-frequency domain, sampling the
channel situation which is the reference of DL demodulation.
Serried RS distribution leads to accurate channel estimation, also high
overhead that impacting the system capacity.
MBSFN: Multicast/Broadcast over a Single Frequency Network
RE
Not used for RS transmission on this antenna port
RS symbols on this antenna port
R1: RS transmitted in 1st ant port
R2: RS transmitted in 2nd ant port
R3: RS transmitted in 3rd ant port
R4: RS transmitted in 4th ant port
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 26
Page 26
Synchronization Signal: synchronization signals are used for time-frequency synchronization between UE and E-UTRAN during cell search.
synchronization signal comprise two parts:
Primary Synchronization Signal, used for symbol timing, frequency synchronization and part of the cell ID detection.
Secondary Synchronization Signal, used for detection of radio frame timing, CP length and cell group ID.
Synchronization Signals Structure
Characteristics: The bandwidth of the synchronization signal is
62 subcarrier, locating in the central part of
system bandwidth, regardless of system
bandwidth size.
Synchronization signals are transmitted only in
the 1st and 11rd slots of every 10ms frame.
The primary synchronization signal is located in
the last symbol of the transmit slot. The
secondary synchronization signal is located in
the 2nd last symbol of the transmit slot.
Downlink Physical Signals (2)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 27
Page 27
Uplink RS (Reference Signal): The uplink pilot signal, used for synchronization between
E-UTRAN and UE, as well as uplink channel estimation.
Two types of UL reference signals: DM RS (Demodulation Reference Signal), associated with
PUSCH and PUCCH transmission.
SRS (Sounding Reference Signal), without associated with
PUSCH and PUCCH transmission.Characteristics:
Each UE occupies parts of the system bandwidth since SC-FDMA
is applied in uplink. DM RS only transmits in the bandwidth
allocated to PUSCH and PUCCH.
The slot location of DM RS differs with associated PUSCH and
PUCCH format.
Sounding RS’s bandwidth is larger than that allocated to UE, in
order to provide the reference to e-NodeB for channel estimation in
the whole bandwidth.
Sounding RS is mapped to the last symbol of sub-frame. The
transmitted bandwidth and period can be configured. SRS
transmission scheduling of multi UE can achieve
time/frequency/code diversity.
DM RS associated with PUSCH is mapped to the 4th symbol each slot
Time
Freq
Time
Freq
Time
Freq
DM RS associated with PUCCH (transmits UL ACK signaling) is mapped to the central 3
symbols each slot
DM RS associated with PUCCH (transmits UL CQI signaling) is mapped to the 2
symbols each slot
PUCCH is mapped to up & down ends of the system bandwidth,
hopping between two slots.
Allocated UL bandwidth of one UE
System bandwidth
Uplink Physical Signals
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 28
Downlink Resource Structure• Downlink Resource Structure
Type I frame, single antenna, ΔF = 15 kHz
Standard RB:
One of center 6 RBs:
Legend:
Downlink Reference SignalsPBCH (Physical Broadcast Channel)
PSS (Primary Synchronisation Signal)
SSS (Secondary Synchronisation Signal)
PDCCH / PHICH / PCFICH (Physical - Downlink Control / HARQ Indicator / Control Format Indicator - Channels)
PDSCH (Physical Downlink Shared Data Channel)
© Forsk 2010
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 29
Downlink Resource Structure
OFDMSymbol 0C
P OFDMSymbol 1C
P OFDMSymbol 3C
P OFDMSymbol 4C
P OFDMSymbol 5C
P OFDMSymbol 6C
POFDMSymbol 2C
P
Legend: Downlink Reference signals
PBCH PSS SSS
PDCCH / PHICH / PCFICH PDSCH
1 subframe = 2 slot (1 ms)
1 frame = 10 subframe (10 ms)
SF 0 SF 1 SF 2 SF 3 SF 4 SF 5 SF 6 SF 7 SF 8 SF 9
7 OFDM symbols at normal CP per slot (0.5 ms)
0 1 2 3 4 5 6 0 1 2 3 4 5 6
Cen
tre
6 R
Bs
© Forsk 2010
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 30
Uplink Resource Structure
OFDMSymbol 0C
P OFDMSymbol 1C
P OFDMSymbol 3C
P OFDMSymbol 4C
P OFDMSymbol 5C
P OFDMSymbol 6C
POFDMSymbol 2C
P
Legend:
UL DMRS (Uplink Demodulation Reference Signal)
UL SRS (Uplink Sounding Reference Signal)
PUCCH (Physical Uplink Control Channel)
(incl.HARQ feedback and CQI reporting)
Demodulation Reference Signal for PUCC
PUSCH (Physical Uplink Shared Data Channel)SF 0 SF 1 SF 2 SF 3 SF 4 SF 5 SF 6 SF 7 SF 8 SF 9
7 OFDM symbols at normal CP per slot (0.5 ms)
0 1 2 3 4 5 6 0 1 2 3 4 5 6
© Forsk 2010
1 subframe = 2 slot (1 ms)
1 frame = 10 subframe (10 ms)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 31
Page 31
Basic Principle of Cell Search: Cell search is the procedure of UE synchronizes with E-UTRAN in
time-freq domain, and acquires the serving cell ID.
Two steps in cell search:
Step 1: Symbol synchronization and acquirement of ID within
Cell Group by demodulating the Primary Synchronization Signal;
Step 2: Frame synchronization, acquirement of CP length and
Cell Group ID by demodulating the Secondary Synchronization
Signal.
About Cell ID : In LTE protocol, the physical layer Cell ID comprises two parts:
Cell Group ID and ID within Cell Group. The latest version defines
that there are 168 Cell Group IDs, 3 IDs within each group. So
totally 168*3=504 Cell IDs exist.
represents Cell Group ID, value from 0 to 167;
represents ID within Cell Group, value from 0 to 2.
(2)ID
(1)ID
cellID 3 NNN
(1)IDN(2)IDN
Initial Cell Search: The initial cell search is carried on after the UE power on. Usually, UE doesn’t
know the network bandwidth and carrier frequency at the first time switch on. UE repeats the basic cell search, tries all the carrier frequency in the spectrum to
demodulate the synchronization signals. This procedure takes time, but the time requirement are typically relatively relaxed. Some methods can reduce time, such as recording the former available network information as the prior search target.
Once finish the cell search, which achieve synchronization of time-freq domain and acquirement of Cell ID, UE demodulates the PBCH and acquires for system information, such as bandwidth and Tx antenna number.
After the procedure above, UE demodulates the PDCCH for its paging period that allocated by system. UE wakes up from the IDLE state in the specified paging period, demodulates PDCCH for monitoring paging. If paging is detected, PDSCH resources will be demodulated to receive paging message.
Search Freq
Sync Signals
PBCH
PDCCH
PDSCH
Physical Layer Procedure — Cell Search
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 32
Page 32
Basic Principle of Random Access : Random access is the procedure of uplink synchronization
between UE and E-UTRAN.
Prior to random access, physical layer shall receive the following information from the higher layers:
Random access channel parameters: PRACH configuration, frequency position and preamble format, etc.
Parameters for determining the preamble root sequences and their cyclic shifts in the sequence set for the cell, in order to demodulate the random access preamble.
Two steps in physical layer random access: UE transmission of random access preamble
Random access response from E-UTRAN
Detail Procedure of Random Access: Physical Layer procedure is triggered upon request of a preamble
transmission by higher layers.
The higher layers request indicates a preamble index, a target preamble received power, a corresponding RA-RNTI and a PRACH resource .
UE determines the preamble transmission power is preamble target received power + Path Loss. The transmission shall not higher than the maximum transmission power of UE. Path Loss is the downlink path loss estimate calculated in the UE.
A preamble sequence is selected from the preamble sequence set using the preamble index.
A single preamble is transmitted using the selected preamble sequence with calculated transmission power on the indicated PRACH resource.
UE Detection of a PDCCH with the indicated RA-RNTI is attempted during a window controlled by higher layers. If detected, the corresponding PDSCH transport block is passed to higher layers. The higher layers parse the transport block and indicate the 20-bit grant.
PRACHRA Preamble
PDCCHRA Response
RA-RNTI: Random Access Radio Network Temporary Identifier
Physical Layer Procedure — Radom Access
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 33
Page 33
Basic Principle of Power Control:
Downlink power control determines the EPRE (Energy per
Resource Element);
Uplink power control determines the energy per DFT-SOFDM
(also called SC-FDMA) symbol.
Uplink Power Control: Uplink power control consists of opened loop power and closed loop power control.
A cell wide overload indicator (OI) is exchanged over X2 interface for integrated inter-
cell power control, possible to enhance the system performance through power
control.
PUSCH, PUCCH, PRACH and Sounding RS can be controlled respectively by uplink
power control. Take PUSCH power control for example:
PUSCH power control is the slow power control, to compensate the path loss and
shadow fading and control inter-cell interference. The control principle is shown in
above equation. The following factors impact PUSCH transmission power PPUSCH: UE
maximum transmission power PMAX, UE allocated resource MPUSCH, initial transmission
power PO_PUSCH, estimated path loss PL, modulation coding factor △TF and system
adjustment factor f (not working during opened loop PC)
UE report CQI
DL Tx Power
EPRE: Energy per Resource Element
DFT-SOFDM: Discrete Fourier Transform Spread OFDM
f(i)}(i)ΔPLα(j)(j)P(i))(M,{P(i)P TFO_PUSCHPUSCHMAXPUSCH 10log10min
Downlink Power Control: The transmission power of downlink RS is usually constant. The
transmission power of PDSCH is proportional with RS transmission power.
Downlink transmission power will be adjusted by the comparison of UE
report CQI and target CQI during the power control.
X2
UL Tx Power
System adjust
parameters
Physical Layer Procedure — Power Control
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 34
Page 34Page 34
Adaptive Modulation and Coding
2 bits per symbol in each carrier.
4 bits per symbol in each carrier.
6 bits per symbol in each carrier.
The most appropriate modulation and coding scheme can be adaptively selected according to the channel propagation conduction, then the maximum throughput can be obtained for different channel situation.
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 35
LTE Feature
• MIMO• ICIC• SON
ANR Automatic Detection and Collision PCI Mobility Load Balancing
• CSFB
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 36
Page 36
Downlink MIMO MIMO is supported in LTE downlink to achieve spatial
multiplexing, including single user mode SU-MIMO and multi user mode MU-MIMO.
In order to improve MIMO performance, pre-coding is used in both SU-MIMO and MU-MIMO to control/reduce the interference among spatial multiplexing data flows.
The spatial multiplexing data flows are scheduled to one single user In SU-MIMO, to enhance the transmission rate and spectrum efficiency. In MU-MIMO, the data flows are scheduled to multi users and the resources are shared within users. Multi user gain can be achieved by user scheduling in the spatial domain.
Uplink MIMO Due to UE cost and power consumption, it is difficult to implement
the UL multi transmission and relative power supply. Virtual-MIMO, in which multi single antenna UEs are associated to transmit in the MIMO mode. Virtual-MIMO is still under study.
Scheduler assigns the same resource to multi users. Each user transmits data by single antenna. System separates the data by the specific MIMO demodulation scheme.
MIMO gain and power gain (higher Tx power in the same time-freq resource) can be achieved by Virtual-MIMO. Interference of the multi user data can be controlled by the scheduler, which also bring multi user gain.
Pre-coding vectors
User k data
User 2 data
User 1 data
Channel Information
User1
User2
User k
Scheduler Pre-coder
S1
S2
Pre-coding vectors
User k data
User 2 data
User 1 data
Channel Information
User1
User2
User k
Scheduler Pre-coder
S1
S2
User 1 data
Channel Information
User1
User2
User kScheduler
MIMO
DecoderUser k data
User 1 data
User 1 data
Channel Information
User1
User2
User kScheduler
MIMO
DecoderUser k data
User 1 data
DL-MIMO Virtual-MIMO
MIMO
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 37
Page 37Page 37
DL MIMO
codeword
UE1
User1SFBC
Mod
SFBC (Transmit Diversity)
Same stream transmitted simultaneously in certain form of MIMO coding at the same time-frequency resource from both antenna ports (Rank = 1)
Depending on the environment & number of antennas, SFBC can reduce fading margin by 2~8 dB, to extend coverage, and enhance system capacity
UE1
Layer 1, CW1, AMC1UE2
Layer 2, CW2, AMC2
MIMO encoder and layer mapping
MCW (Spatial Multiplexing)
Multiple data streams transmitted at the same time-frequency resource from different antenna ports
The terminal must have at least 2 Rx antennas for spatial multiplexing (SM)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 38
Page 38
Frequency
Cell 3,5,7Power
Frequency
Cell 3,5,7Power
Frequency
Cell 2,4,6Power
Frequency
Cell 2,4,6Power
ICIC is one solution for the cell interference control, is essentially a schedule strategy. In LTE, some coordination schemes( ICIC )
can control the interference in cell edges to enhance the frequency reuse factor and performance in the cell edges.
1
2
3
6
5
7
4
1
2
3
6
5
7
4
The edge band is assigned to the users in cell edge. The eNB transmit power of the
edge band can be high.
Center Band
Cell 2,4,6 Primary Band
Frequency
Cell 1Power
Frequency
Cell 1Power
Cell 1 Edge Band
Center Band
Cell 3,5,7P Edge Band
The center band is assigned to the users in cell center. The eNB transmit power of the center band
should be reduced in order to avoid the interference to the edge band of neighbor cells.
Center Band
Center Band
ICIC ( Inter-Cell Interference
Coordination )
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 39
SON ( Self-Organising Networks )• SON Brief Introduction
SON (Self Organization Network) is the functions of LTE that required by the NGMN (Next Generation Mobile Network) operators.
From the point of view of the operator’s benefit and experiences, the early communication systems had bad O&M compatibility and high cost.
New requirements of LTE are brought forward, mainly focus on FCAPSI (Fault, Configuration, Alarm, Performance, Security, Inventory) management:
Self-planning and Self-configuration, support plug and play
Self-Optimization and Self-healing
Self-Maintenance
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 40
Page 40
Add new Sites
New site configured site
Description:
• Auto configure and optimize Neighbor
relations, intra-LTE and inter-RAT
• X2 automatic setup
• Operator defined rules and monitoring
supported
Description:
• Auto configure and optimize Neighbor
relations, intra-LTE and inter-RAT
• X2 automatic setup
• Operator defined rules and monitoring
supported
Benefits:
• Fast definition of Neighbor Relations
• up to 95% lower cost of neighbor relation
planning and optimization
• Improve customer experience by reducing
HO failure caused by missing neighbor
relations
Benefits:
• Fast definition of Neighbor Relations
• up to 95% lower cost of neighbor relation
planning and optimization
• Improve customer experience by reducing
HO failure caused by missing neighbor
relations
SON_ANR (Automatic Neighbor Relation)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 41
Page 41
ANR functionality ANR management is implemented through the following functions:
Automatic detection of missing neighboring cells Automatic evaluation of neighbor relations Automatic detection of Physical Cell Identifier (PCI) collisions Automatic detection of abnormal neighboring cell coverage
Automatic Neighbor Relation (ANR) can automatically add and maintain neighbor relations. The initial network construction, however, should not fully depend on ANR for the following considerations:
ANR is closely related to traffic in the entire network ANR is based on UE measurements but the delay is introduced in the measurements.
After initial neighbor relations configured and the number of UEs increasing, some neighboring relations may be missing. In this case, ANR can be used to detect missing neighboring cells and add neighbor relations.
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 42
Page 42
ANR functionality Two main type of ANR:
Event triggered Periodical reporting – fast ANR
• Both Event triggered and Fast ANR are applicable for same system or different systems
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 43
SON_Automatic Detection of PCI Collisions
• A PCI collision means the serving cell and a neighboring cell have the same PCI but different ECGIs. PCI collisions may be caused by improper network planning or abnormal neighboring cell coverage (also known as cross-cell coverage). If two neighboring cells have the same PCI, interference will be generated.
• When a PCI collision occurs, the eNodeB cannot determine the target cell for a handover. In this situation, the handover performance deteriorates and the handover success rate is reduced.
• After a PCI collision is removed, the following conditions are met: The PCI is unique in the coverage area of a cell. The PCI is unique in the neighbor relations of a cell.
Page 43
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 44
SON_Automatic Detection of PCI Collisions Cont.Automatic Detection of PCI Collisions• After a neighbor relation is added to the NRT, the eNodeB compares the PCI of the new neighboring cell with the
PCIs of existing neighboring cells in the case of IntraRatEventAnrSwitch is set to ON. If the new neighboring cell and an existing neighboring cell have the same ECGI but different PCIs, the eNodeB reports a PCI collision to the M2000. The M2000 collects statistics about PCI collisions and generates a list of PCI collisions.
Reallocating PCIs • PCI reallocation is a process of reallocating a new PCI to a cell whose PCI collides with the PCI of another cell. The
purpose is to remove PCI collisions. • The M2000 triggers the PCI reallocation algorithm to provide suggestions on PCI reallocation.
Note: • After the PCI of a cell is changed, the cell needs to be reestablished and the services carried on the cell are
disrupted. Therefore, the PCI reallocation algorithm only provides reallocation suggestions. A PCI can be reallocated manually or automatically through a scheduled task configured on the M2000.
Page 44
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 45
Page 45
Cell A Cell B Cell C
Cell CCell BCell A
Description:
• Exchange cell load information over X2
• Offload congested cells
• Optimize cell reselection / handover
parameters
Description:
• Exchange cell load information over X2
• Offload congested cells
• Optimize cell reselection / handover
parameters
Benefits:
• Increase 10% system capacity and 10%-20%
access success rate in unbalance scenario
• Improve customer experience by reducing
call drop rate, handover failure rate, and
unnecessary redirection caused by
unbalanced load
Benefits:
• Increase 10% system capacity and 10%-20%
access success rate in unbalance scenario
• Improve customer experience by reducing
call drop rate, handover failure rate, and
unnecessary redirection caused by
unbalanced load
SON_MLB( Mobility Load Balancing)
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 46
How to solve Mobility
Problems?
PING PONG
unnecessary HO Rate
HO successful rate
Valu
e
Before adopt MRO After adopt MRO
Description:
• HO parameters are optimized based
upon long term UE mobility behavior
• Avoid Ping-Pong handover, handover
too early, handover too late, etc
Description:
• HO parameters are optimized based
upon long term UE mobility behavior
• Avoid Ping-Pong handover, handover
too early, handover too late, etc
Benefits:
• Reduce cost of mobility optimization
• Improve customer experience by reducing
call drop rate and handover failure rate
Benefits:
• Reduce cost of mobility optimization
• Improve customer experience by reducing
call drop rate and handover failure rate
SON_MRO( Mobility Robust Optimization )
HUAWEI TECHNOLOGIES CO., LTD.
THANK YOU
Top right corner for field-mark, customer or partner logotypes.
---------------- The following nine groups of colors are an example of how our design colors can be used, please take note that you should only use one design color group per slide. For specific usage details, refer to the “Typesetting Standard”.
Copyright©2011 Huawei Technologies Co., Ltd. All Rights Reserved. 48
PAPR
Cyclic Prefix