LoopDeLoop
Transcript of LoopDeLoop
-
8/3/2019 LoopDeLoop
1/3
publishers ofStep by Step Wire Jewelrymagazine . . . join the online beading community at www.BeadingDaily.com
This cool project uses two sterling banglebracelets. Wrap them together with silver craftwire and accentuate with crystals for an eye-catching piece!
by Allison Hoffman, for FusionBeads.com
Sparkling wire bracelet.
Loop de Loop Bangle
MATERIALS:26-gauge non-tarnish silver Artistic Wire, 42'
26-gauge copper wire, 10"
4mm Sand Opal CRYSTALLIZED-Swarovski Elements crystal mix, 6
4mm Jonquil CRYSTALLIZED- SwarovskiElements crystal, 9
4mm Khaki CRYSTALLIZED- SwarovskiElements crystal mix, 10
4mm Light Topaz CRYSTALLIZED- SwarovskiElements crystal mix, 5
4mm Lime CRYSTALLIZED- SwarovskiElements crystal mix, 3
6mm Lime CRYSTALLIZED- SwarovskiElements crystal round bead, 4
6mm Light Gray Opal CRYSTALLIZED-Swarovski Elements crystal round bead, 6
2-1/2" diameter sterling flat bangle bracelet,2
TOOLS:Chain nose pliersFlush cutters
RulerBlack Sharpie
RESOURCES:All materials from FusionBeads.com
TECHNIQUES:Wirework, wirewrapping, beading.
RRRRRRRRRRRRRRRRRRRRRRRRRRR
projectlibrary
Copyright Interweave Not to be reprinted. All rights reserved.
page 1
Photooffin
ishedpiecebyJim
Lawson;allotherphotoscourtesyoftheauthor.
TIP:Prior to using your beads, make sure you testeach one so you can fit two pieces of 26g wirethrough them.
-
8/3/2019 LoopDeLoop
2/3
Step 1: Cut five 2" piecesof copper wire. Toanchor, use one
piece and wrap itaround the topbangle twice.
Step 2: Starting with the top bangle, use a ruler andmeasure 1/2" down the copper wire, and mark.Wrap the copper wire around the bottombangle, making sure the mark on the wire is
lined up with the bottom bangle. Anchor thecopper wire to the bottom bangle by wrapping
the wire twice around the bangle.
Step 3: Repeat Steps1-2 five
more times,making sure
the copperwires are
spread outevenly along thebangles.
Step 4: In the middle ofone of the copperwraps, take a 2'
piece of silverwire, and wrap
around the topbangle once toanchor the wire in
place. Wrap thewire 19 more times
to the right.
Step 5: Add two beadsto the wire.Wrap the wire
around thebottom bangleonce to anchor
it in place.
Step 6: Bring the wireback upthrough the
bead closest tothe bottom.
Pull the wire all
the waythrough thebead.
Step 7: Loop the wirearound the
bead so itframes the
bead.
Step 8: Go back upthrough the next
bead and pullthe wire all the
way through.
Step 9: Loop the wire around the bead in the oppositedirection of the first wire loop so it will form afigure 8 pattern. Bring the wire through the
back of the top bangle.
Loop de Loop Bangle
Copyright Interweave. Not to be reprinted. All rights reserved.
page 2
publishers ofStep by Step Wire Jewelrymagazine . . . join the online beading community at www.BeadingDail
Step 1
Step 2
Step 4
Step 5
Step 3
Step 7
Step 8
Step 9
Step 6
-
8/3/2019 LoopDeLoop
3/3
publishers ofStep by Step Wire Jewelrymagazine . . . join the online beading community at www.BeadingDaily.c
Step 10: Wrap the wirearound thetop bangle
once to
anchor it inplace. Wrapthe wire 19
more times tothe right.
Step 11: Start with thebottom
bangle, andrepeat Step
10.
Step 12: Slide thewrapped wireso it butts upagainst the
bead on theleft.
Step 13: Add two beads
to the wire,and repeatSteps 5-9, thistime going
through theback of the
bottom bangle.Wrap once to
anchor it in place.
Step 14: Wrap the wire 19more times.
Step 15: Repeat Steps 4-14 until thebangle is
completely
covered withwraps (or about10 1/2 times).
You can removethe copperwrap anchors
as you go along.The last wrap of
wire should be against the first wrap that wasmade. Trim the tail of the wire.
Loop de Loop Bangle
Copyright Interweave. Not to be reprinted. All rights reserved.
page 3
Step 10
Step 12
Step 11
Step 13
Step 14
Step 15
http://www.interweave.com/go/bdsw