LNC Technology Co., Ltd. 1

Leading Numerical Controller

LNC-T520i

OOppeerraattoorr''ss MMaannuuaall2007/10 VerV04.00.000

LNC Technology Co., Ltd.

LNC T520i Table of Content

Pou Yuen Technology Corp. I

Table of Content

1 GENERAL ............................................................................................... 1

1.1 HARDWARE SPECIFICATION ................................................................................. 2

1.2 SOFTWARE SPECIFICATION.................................................................................. 3

1.3 SYSTEM SETTING UNIT ....................................................................................... 4

1.4 G CODE TABLE................................................................................................... 5

2 CNC OPERATION................................................................................... 7

2.1 OPERATION INSTALLATION TYPE........................................................................... 7

2.2 OPERATION INSTALLATION INSTRUCTION............................................................... 8

2.3 SCREEN AND FUNCTION DESCRIPTION ............................................................... 13

2.3.1 Display Screen Layout....................................................................... 13

2.3.2 Function Groups ................................................................................ 14

2.3.3 ABS (Absolute Coordinate) ............................................................... 22

2.3.4 REL (Relative Coordinate)................................................................. 23

2.3.5 MAC (Machine Coordinate) ............................................................... 24

2.3.6 Exit System Screen ........................................................................... 25

2.4 PROG FUNCTION ............................................................................................ 26

2.4.1 FGPROG (Foregoing Program)......................................................... 27

2.4.2 BGPROG (Background Program) ..................................................... 29

2.4.3 PROCHK (Program Checking) .......................................................... 30

2.4.4 DIR MNG (File Management)............................................................ 32

2.4.5 RS232 ............................................................................................... 41

2.4.6 DNC Function.................................................................................... 46

2.5 OFFSET......................................................................................................... 47

2.5.1 WEAR (Wear OFFSET)..................................................................... 47

2.5.2 GEOM (Geometry OFFSET) ............................................................. 50

2.5.3 W. SHIFT (Work Coordinate Shift)..................................................... 51

2.5.4 MACRO............................................................................................. 52

2.5.5 WORK (Coordinate Setting) .............................................................. 54

2.6 LATHE EASY-CAM .......................................................................................... 57

2.6.1 Function Description.......................................................................... 57

2.6.2 Operation Procedure of How to Produce Working Path Program...... 57

2.6.3 Operation Screen and Function Key Instruction ................................ 59

LNC T520i Table of Content

II Pou Yuen Technology Corp.

2.7 GRAPHGRAPH ...................................................................................... 85

2.7.1 Function Introduction ......................................................................... 85

2.7.2 SIMU ................................................................................................. 85

2.7.3 Window Definition.............................................................................. 88

2.8 DGNOS.......................................................................................................... 90

2.8.1 ALARM.............................................................................................. 90

2.8.2 System Upgrade................................................................................ 93

2.8.3 IOCSA ............................................................................................. 100

2.8.4 MLC2............................................................................................... 102

2.8.5 SYSTEM.......................................................................................... 107

2.9 SOFTPL........................................................................................................110

2.10 PARAM .........................................................................................................112

2.10.1 NC. SYS (System Parameter) ..........................................................112

2.10.2 Users Parameter ..............................................................................116

2.10.3 Authorization ....................................................................................117

2.11 RESET......................................................................................................... 122

3 OP PANEL OPERATION..................................................................... 123

3.1 POWER SWITCH (ON/OFF)............................................................................. 124

3.2 EMG-STOP KEY........................................................................................... 125

3.3 CYCLE START............................................................................................. 126

3.4 FEED HOLD................................................................................................. 127

3.5 LED SIGNAL................................................................................................ 127

3.6 MODE SELECT ........................................................................................... 128

3.7 AXIS SELECTION........................................................................................ 129

3.8 SPINDLE ROTATION................................................................................... 130

3.9 CHUCK .......................................................................................................... 131

3.10 OT RELEASE............................................................................................... 132

3.11 COOLANT SUPPLY..................................................................................... 133

3.12 TOOL MAGAZINE........................................................................................ 133

3.13 WORKING LIGHT AND TAIL-BASE BUTTON ......................................................... 134

LNC T520i General

LNC Technology Co., Ltd. 1

1 General

LNC-T520i is a PC-based controller for CNC lathe machines. It is a highly technology product that is developed by the POU YUEN TECHNOLOGY Ltd. through years of dedicating research and development, involving massive manpower and resources. LNC-520i serial controller is featured in highspeed, highprecision, and highefficiency.

In the following chapters, operating instruction of LNC-T520i controller will be introduced.

LNC T520i General

2 LNC Technology Co., Ltd.

1.1 Hardware Specification

LNC-520i Specification

Display device 8.4Color TFT LCD

CPU GX1-300

DRAM RAM 64M bytes or above

Double CF Card Each 32M bytes or above

Floppy Diskette Panel and Power Standard FDD5V/12V

PCCPU BOARD Industrial PC Board

Spindle System Support Pulse Control Plus DA Output Remote I/O 128 Input / 128 Output

USER I/O 20 Input / 16 Output

Servo System Provide Position/Speed Circuit Control DNC RS232 19200 Baud Rate

Operation Panel Standard Milling OP Panel

Hand Wheel Panel 3 in 1 MPG

Controllable Axis 3 Axes Linear Interpolation Simultaneous Axis 3 Axes

Arch Interpolation Simultaneous Axis 3 Axes

MPG Controllable Axis 3 Axes

Spindle Axis 1 Axis

Min. Input Unit 0.001 mm 0.0001 inch 0.001 deg

Min. Commanding Unit 0.001 mm 0.0001 inch 0.001 deg

Power Supply

(First Power Set) 12V(2A)5V(6A) (Second Power Set) 24V(2A)

LNC T520i General

LNC Technology Co., Ltd. 3

1.2 Software Specification

LNC-T520i Specification

File Format DOS FAT Program Specification Normal G, M Code Program

Background Editing Function Macro Program Function Module Type EDIT

MEM MDI JOG MPG RAPID HOME Screen Group Function POS

PROG OFFSET CAM GRAPH DGNOS SOFTPL PARAM MLCMachine Logic Controller I/O/C/S/A BIT

Timer/Counter/Register Ladder Program Display Language Tradition/Simplify Chinese and

English

LNC T520i General

4 LNC Technology Co., Ltd.

1.3 System Setting Unit

Min. Input Unit Min. Commanding Unit Max. Travel Setting 0.001 mm 0.001 mm 99999.999 mm 0.0001 inch 0.0001 inch 9999.9999 inch 0.001 deg 0.001 deg 99999.999 deg

LNC T520i General

LNC Technology Co., Ltd. 5

1.4 G Code Table

Function Description Group TYPE A TYPE B TYPE C

Positioning (Ra