list1
Transcript of list1
This section lists works approved by Lloyd’s Register Group for steelmaking and themanufacture of rolled steel plate, strip, sections and bars in accordance with therequirements of LR's Rules and Regulations for the Classification of Ships Part 2, Chapter 3.
The information listed for each works is a summary of the product, generic grade andmaximum thickness, or in the case of round bars, diameter approved.
It is important to note that this List does not provide full details of the grades approved byLR as required by the Rules. The combinations of deoxidation practice ( e.g. killed,semi-killed), micro-alloying and grain refining additions (e.g. Al, Al + Nb Al + Nb + V,etc.), in association with specific rolling procedures ( e.g. N or TM, etc.), are not included. These parameters may vary within each grade bymanufacturer and could influence the fabrication procedures that can be applied.
Where required this information should be obtained from the current certificate of approvalissued to the manufacturer by LR.
Works designated ( Q.A. Approved ) are also approved under the Quality Scheme forMaterials in accordance with LR's Rules and Regulations for the Classification of ShipsPart 2, Chapter 1 Section 2.
The list also includes firms approved for the manufacture of fabricated steel sections andsteel by powder metallurgy.
Approval only covers the manufacturing location listed, it does not extend to other worksowned by the same company.
The local LR surveying office is also listed.
Abbreviations
B.O.S. Basic Oxygen Steelmaking
Con Cast Continuous Casting
E.A.F. Electric Arc Furnace
O.H. Open Hearth
NOTICE AND TERMS OF USE Lloyd's Register, its affiliates and subsidiaries and their respective officers, employees oragents are, individually and collectively, referred to in this clause as the 'Lloyd's RegisterGroup'. The Lloyd's Register Group assumes no responsibility and shall not be liable to anyperson for any loss, damage or expense caused by reliance on the information or advice inthis document or howsoever provided, unless that person has signed a contract with the
List 1
Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
As at 06 November 2012
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Argentina
carbon, carbon-manganese 30E.A.F. / IngotSteelmakingACEROS ANGELETTI S.A. Buenos Airescarbon, carbon-manganese 30IngotsSemi-Finished
Av. Hipolito Yrigoyen 16102/96(1852)-Burzaco
Burzaco
Tel No: +54 11 4299 0110 Fax no: +54 11 4299 0110Email:[email protected]: www.acerosangeletti.com.arCertificate No. MD00/3676/ 0002/ 1 Expiry date 22/02/2015
Pcia. de Buenos Aires
Australia
As belowB.O.S. / Con CastSteelmakingBLUESCOPE STEEL (AIS) PTY. LTD. SydneyA, B, D, E 51Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
51Higher Strength
A, B, D, E 13Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
6Higher Strength
P.O. Box 1854Wollongong
Port Kembla Steelworks
Tel: +61 2 42754666 Fax: +61 2 42753045 Email: mailto:[email protected] with specified through thickness properties notation Z35 may be added.Normalizing heat treatments carried out by sub-contractor, Bisalloy.
Certificate # MD00/1929/0008/1 Expiry date: 20/07/2015
NSW 2500
Austria
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
E.A.F./Ingot/Con CastSteelmakingBREITENFELD EDELSTAHL AG Vienna
A-8662 Mitterdorf im MürztalBreitenfeldstrasse 22
Including VD/VOD Tel: +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248 Email mailto:[email protected]: http://www.breitenfeld.atCertificate # MD00/3255/0003/1 Expiry Date: 08/06/2012
As belowE.A.F./Ingot/Con CastSteelmakingBÖHLER EDELSTAHL GmbH Viennacarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
220StructuralBars
Postfach 96A-8605 Kapfenberg
Mariazellerstraße 25
Tel: +43 3862 20 37063 Fax: +43 3862 20 37559 Email: mailto:[email protected] Web:http://www.bohler-edelstahl.comCertificate #: MD00/0200/0007/1 Expiry date: 22/01/2015
A, B, D, E 20Normal StrengthSectionsBÖHLER YBBSTAL PROFIL GmbH ViennaAH32, AH36, DH32, DH36, EH32, EH36 20Higher StrengthA, B, D, E 20Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 20Higher Strengthcarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
20Structural
Waidhofnerstraße 83333 BöhlerwerkTel: +43 7448 7007 504 Fax: +43 7448 7007 250 Email: mailto:[email protected] Web:http://www.bohler-profil.comHigh alloy bars and sections may be accepted for approved applications.Certificate #: MD00/0202/0006/1 Expiry date: 28/01/2015
carbon, carbon-manganese, alloy, austeniticstainless, duplex
38IngotsESRSONDERSTAHLWERK BREITENFELD GmbH Vienna
A-8661 WartbergBreitenfeldgasse 23
Including remelting of Ni materialsTel +43 (0)3858 6161 231 Fax +43 (0)3858 6161 248 Email [email protected] Web http://www.breitenfeld.atCertificate # MD00/3256/0003/1 Expiry date: 08/06/2012
As at 06 November 2012 2Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 120Normal StrengthBarsSTAHL JUDENBURG GmbH Viennacarbon, carbon-manganese 120Structuralcarbon, carbon-manganese, carbon-manganese 120Machinery
Gußstahlwerkstrasse 21A-8750 JudenburgTel: +43 3572 701-358 Fax: +43 3572 701-248 Email: mailto:[email protected] Web: http://www.stahl-judenburg.comCertificate #: MD00/1643/0006/1 Expiry date: 29/01/2015
As belowB.O.S. / Con CastSteelmakingVOESTALPINE GROBBLECH GmbH ViennaA, B, D, E 140Normal StrengthPlatesAH40, AH42, DH40, DH42, EH40, EH42 55Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36
140
360AR 40Boiler & Pressure Vessel410AR 50360FG, 410FG, 460FG, 490FG, 510FG 1401.5Ni, 3.5Ni, 5Ni, 9Ni 50Ferritic Low TemperatureLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36
140
D/304L 50CladP.O Box 3Voest.- Alpine - Str. 3
Tel: +43 50304 15 9091 Fax: +43 50304 55 9091Email: mailto:[email protected]: www.voestalpine.comMD00/1614/0007/1 Expiry date: 30/07/2014
A-4020 Linz
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingVOESTALPINE STAHL DONAWITZ GmbH & Co KG Viennacarbon, carbon-manganese, alloy 285Blooms/BilletsSemi-Finished
A 8700 LeobenKerpelystraße 199
Tel: +43 50304 25-4659 Fax: +43 50304 65-2464 Email: mailto:[email protected] Web:http://www.voestalpine.com/stahldonawitzCertificate #: MD00/2976/0004/1 Expiry date: 21/04/2015
Belgium
austenitic stainlessE.A.F./A.O.D./Con CastSteelmakingAPERAM Genk Antwerpaustenitic stainlessB.O.S/V.O.D./Con Castaustenitic stainless 200SlabsSemi-Finished304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347
14Austenitic StainlessPlates
Swinnenwijerweg 5Genk - Zuid, Zone 6A
Tel: +32 89 30 25 68 Fax: +32 89 30 25 53 Email: [email protected] #: MD00/3423/0003/1 Expiry date: 29/01/2014
B-3600 Genk
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingDUFERCO LA LOUVIÈRE S.A. Antwerpcarbon, carbon-manganese, Normal strength,Higher Strength
250SlabsSemi-Finished
B-7100 La Louvière2, Rue Des Rivaux
Tel: +32 6427 2912 Email mailto:[email protected] #: MD00/3380/0002/1 Expiry date: 24/09/2013
As belowE.A.F./Ingot/Con CastSteelmakingESB sprl Antwerpcarbon, carbon-manganese, alloy 16IngotsSemi-Finishedcarbon, carbon-manganese, alloy, FerriticStainless Steel*
600Blooms
Rue de l'Environnement, 8B - 4100
ENGINEERING STEEL BELGIUM
Tel No: +32 433 885 56 Fax No: +32 433 809 00Email : [email protected] : www.esb.beCertificate No: MD00/3858/000/1 Expiry date: 10/11/2013Materials Suitable for Steel Forgings, Pipe and Tube, Ingots up to 800mm diameter and Blooms up to 600 mm diameter
Seraing
As belowE.A.F. / Con CastSteelmakingINDUSTEEL BELGIUM SA AntwerpA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36, EH40 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69, FH42, FH46,FH50, FH55, FH62, FH69
100
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, 5Ni
50Ferritic Low Temperature
As at 06 November 2012 3Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Belgium304L, 304LN, 316L, 316LN 50Austenitic StainlessPlatesINDUSTEEL BELGIUM SA AntwerpUNS S31803(MOD)* 40Duplex Stainless
266, Rue de ChâteletB-6030 Charleroi
ARCELOR MITTAL GROUP
Tel: +32 71 44 14 51 Fax: +32 71 44 19 29 Email: mailto:[email protected] Web: http://www.arcelormittal.com* accepted for approved applicationsQuenched and tempered grades with specified through thickness propertiesCertificate #: MD00/0477/0008/1 Expiry date: 08/07/2014
A, B, D, E 120Normal StrengthPlatesNLMK CLABECQ S.A. AntwerpAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
120Higher Strength
360AR, 410AR 25Boiler & Pressure Vessel360, 410 50360FG, 410FG, 460FG, 490FG, 510FG 120
Rue de Clabecq, 101B-1460 IttreTel: +32 (0) 2 3919227 Fax: +32 (0)2 3919883 Email:[email protected] Web:http://www.eu.nlmk.comMQS Approved - Approval No. MQS016Certificate #: MD00/2204/0011/1 Expiry date: 24.06.2015
Brazil
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELORMITTAL BRAZIL S/A (ARCELORMITTALTUBARÃO )
Rio de Janeiro
carbon, carbon-manganese 250SlabsSemi-Finished
D 16Normal StrengthHot Rolled Coil
A, B 19
AH27S, AH32 16Higher Strength
460FG, 490FG 16Boiler & Pressure Vessel
360FG, 410FG 19
930 - Jardim Limoeiro29164-970 Serra/ES
Av. Brigadeiro Eduardo Gomes
Carbon and carbon-manganese grades cover the following LR normal and higher tensile strength grades. A, B, D, E, AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36Tel: +55 27 3348 3261 Fax: +55 27 3348 2211 Email : mailto:[email protected]: http://www.arcelormittal.com/br/Certificate #: MD00/0342/0008/1 Expiry date: 01/07/2014
As belowB.O.S./Ingot/Con CastSteelmakingGERDAU AÇOMINAS S.A. Rio de JaneiroCarbon, Carbon-Manganese, Alloy 180Rolled BilletsSemi-Finishedcarbon, carbon-manganese, alloy 250Slabscarbon, carbon-manganese, alloy 300Bloomscarbon, carbon-manganese, alloy 180BilletsCarbon, Carbon-Manganese, Alloy 450Rolled SlabsCarbon, Carbon-Manganese, Alloy 900Rolled Blooms
Rodovia MG-443 KM 7Fazenda do Cadete
Tel: +55 3137 493471 Fax: +55 3137 3215 Email: mailto:[email protected] web http://www.gerdau.com.brSlabs and blooms intended for plates and forgingsCertificate #: MD00/2071/0006/1 Expiry date: 26/02/2015
36420-000-Ouro Branco-MG
As belowE.A.F. / IngotSteelmakingGERDAU S/A São Paulocarbon, carbon-manganese 4IngotsSemi-Finishedcarbon, carbon-manganese 125MachineryBarsR3 117Chain Cable StockU1, U2, U3 125
As at 06 November 2012 4Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Rod.Luiz Dumont Villares km 2- Moreira CésarCEP 12442-260
Pindamonhagaba Plant
Tel: +55 12 2126 7174 Fax: +55 12 2126 7325 Email: mailto:[email protected] Web:http://www.gerdau.com.brBars for grade R3 chain cable is restricted to supply to Companhia Brasileira Amarras with specification EC-Gr.3a.Ingots as semi-finished products to the above maximum weight nominal 630mm x 530mm x 2150mm long are accepted for further processing for rolledproducts.Certificate #: MD00/2867/0006/1 Expiry date: 24/03/2014
Pindamonhangaba S.P.
As belowB.O.S. / Con CastSteelmakingUSIMINAS Rio de JaneiroA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50A 12Normal StrengthHot Rolled Coil360, 410 12Boiler & Pressure Vessel
Av. Pedro Linhares Gomes, 5431Distrito Usiminas, CEP 35160-900
Usinas Siderúrgicas de Minas Gerais S/AUsina Intendente Câmera
Tel +55 (0)31 38293136 Fax +55 (0)31 38293516 Email: mailto:[email protected] and Z35 through thickness properties for plates of approved grades in the TM+Acc and TM+Acc+Temper conditionsMaterials Quality Scheme Approved - MQS014Certificate #: MD00/1603/0007/1 Expiry date: 24/06/2014
Ipatinga, Minas Gerais
As belowB.O.S. / Con CastSteelmakingUSINAS SIDERÚRGICAS DE MINAS GERAIS S.A. -USIMINAS
São Paulo
A, B, D, E 80Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 80
Rodovia Cônego Domênico Rangoni, Km 6Vila da Indústrias 11573-900
Tel: +55 13 3362-2978 Fax: +55 13 3362-3775 Email: mailto: [email protected] Web:http://www.usiminas.comSpecified through thickness properties for plates in the normalised condition, rolled from ingots, up to 35 mm thickness.Specified through thickness properties for plates of grades up to DH32 and thickness up to 26mm in the normalised condition, rolled from continuously castslab.Material Quality Scheme approved, MQS 044Certificate #: MD00/1193/0008/1 Expiry date: 29/09/2014
Cubatão - São Paulo
Bulgaria
As belowE.A.F. / Con CastSteelmakingSTOMANA INDUSTRY AD SofiaAs below 200Blooms/BilletsSemi-FinishedA 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
1, Vladaysko Vastanie Str.2304 PernikTel: +359 76 68 1730 Fax: +359 76 670 250 Emailmailto:[email protected] Web: http://www.stomana.bgCertificate #: MD00/1868/0008/1 Expiry date: 17/04/2013
As at 06 November 2012 5Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Canada
As belowB.O.S. / Con CastSteelmakingESSAR STEEL ALGOMA INC. TorontoD, E 50Normal StrengthPlatesA, B 60AH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
Sault Ste. MarieOntario
105 West Street
Tel +1 705 945 2603 E-mail: mailto:[email protected] Web:http://www.algoma.comCertificate #: MD00/0092/0006/1 Expiry date: 06/05/2014
P6A 5P2
As belowE.A.F. / Con CastSteelmakingGERDAU AMERISTEEL CORPORATION TorontoA 26Normal StrengthSections
Cambridge
Cambridge Division160 Orion Place
Tel: +1 519 740 2488 ext 1420 Fax: +1 519 623 2062 Email: mailto:[email protected] Web:http://www.gerdauameristeel.comCertificate #: MD00/3046/0003/1 Expiry date: 01/02/2013
N1T 1R9
As belowE.A.F. / Con CastSteelmakingGERDAU AMERISTEEL WHITBY TorontoA, B 15Normal StrengthSectionsAH27S, AH32, AH36 15Higher Strength
WhitbyOntario L1N 5T1
Hopkin Street South
CSA grades 260W, 300W and 350W may be accepted for approved applications as equivalent to the appropriate Lloyd's Register grade stated above.
Tel: +1 905 668 8811 ext 2744 Fax: +1 905 668 9361 Email: mailto:[email protected] Web: http://www.gerdauameristeel.comCertificate #: MD00/0322/0007/1 Expiry date: 31/01/2014
China, People's Republic of
A, B, D, E 100Normal StrengthPlatesANGANG STEEL COMPANY LIMITED DalianAH42, AH46, AH50, AH55, DH42, DH46, DH50,DH55, EH42, EH46, EH50, EH55, FH42, FH46,FH50, FH55
80Higher Strength
AH27S, AH32, AH36, DH27S, DH32, DH36,DH40, EH27S, EH32, EH36, EH40, FH27S, FH32,FH36, FH40
100
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 501.5Ni, 3.5Ni, 5Ni, 9Ni 40Ferritic Low Temperature
Honqi Road, Lishan District,Anshan City,
HEAVY PLATE MILL OF MEDIUM AND HEAVY PLATE PLANT
Tel: +86 412 673 4836 Fax: +86 412 672 5766 Email mailto:[email protected] Web http://www.ansteel.con.cnAll grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.Certificate Number: MD00/1869/0009/1 Expiry: 23/03/2015
Liaoning Province
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED DalianNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
Anshan CityLiaoning Province
MEDIUM PLATE MILL OF MEDIUM AND HEAVY PLATE PLANTAngang Area
Tel +86 0412 675 1030 Fax +86 0412 675 2819 Email mailto:[email protected] as semi finished products nominal 2000mm width x nominal 7000mm length to the above maximum thickness are approved for further processing forrolled products.Certificate No. MD00/2757/0007/1 Expiry date: 23/10/2014
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED DalianA, B, D 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
20Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel
No 3 STEELMAKING & HOT ROLLING PLANTTiexi DistrictTel: +86 412 6334292/6734881 Fax: +86 412 6722093 Web http://www.ansteel.com.cnCertificate #: MD00/3301/0002/1 Expiry date: 03/01/2013
As at 06 November 2012 6Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingANGANG STEEL COMPANY LIMITED Daliancarbon-manganese, carbon, carbon manganese 250Blooms/BilletsSemi-FinishedA, B, D, E 40Normal StrengthPlatesAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40
40Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel
115000 BayuquanYingkou City
BAYUQUAN 5500 HEAVY PLATE MILL
Tel: +86 412 6334292 Fax: +86 412 6722093 Web: www.ansteel.com.cnCertificate No. MD00/3595/0002/1 Expiry date: 11/05/2012
Liaoning Province
As BelowB.O.S./E.A.F./Con CastSteelmakingANYANG IRON & STEEL CO., LTD. WuhanNormal strength 230SlabsSemi-FinishedA, B, D 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 36Higher Strength360AR, 410AR, 460FG, 490FG, 510FG 36Boiler & Pressure Vessel360FG, 410FG 40A, B 12Normal StrengthSections
Anyang CityHenan Province
Yindu District
Tel: +86 372 3122486 Fax: +86 372 3121403 email:mailto:[email protected]:http://www.agsteel.com.cnCertificate #: MD00/2200/0008/1 Expiry date: 20/01/2013
As belowB.O.S. / Con CastSteelmakingBAOSHAN IRON & STEEL CO., LTD. Shanghai PortAs belowB.O.S. / Ingotcarbon, carbon-manganese 400SlabsSemi-Finishedcarbon, carbon-manganese, alloy 450Bloomscarbon, carbon-manganese, alloy 200BilletsA, B, D, E 130Normal StrengthPlatesAH42, AH46, AH50, AH55, DH42, DH46, DH50,DH55, EH42, EH46, EH50, EH55
50Higher Strength
AH40, DH40, EH40, FH27S, FH32, FH36, FH40 68AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH40, LTDH40, LTEH40, LTFH27S, LTFH32,LTFH36, LTFH40
68Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36
80
A, B, D 22Normal StrengthHot Rolled CoilAH32, AH36 12Higher Strength460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22
No 885, Fujin RoadBaoshan District
Core Base
Tel +86 21 2664 8888 Fax +86 21 2664 8000 Web:http://www.baosteel.comIncluding all plate grades and thicknesses with specified through thickness properties (Z35)Semi Finished Products - Killed for further processing for forgings, Fine Grain for further processing for rolled products.Certificate #: MD00/1343/0013/1 Expiry date: 30/03/2013
Materials Quality Scheme Approved - MQS 038
Shanghai 201900
As belowB.O.S. / Con CastSteelmakingBAOSHAN IRON & STEEL CO., LTD. Shanghai Portcarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D, E 60Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
460FG, 490FG, 510FG 50Boiler & Pressure Vessel360FG, 410FG 60
As at 06 November 2012 7Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Baoshan DistrictShanghai 200949
Core Base Plate Line No. 2No. 777 North Wenchuan Road
Tel +86 21 266488888 Fax +86 21 2664 8000 Email: to: [email protected] Web:http://www.baosteel.com
Semi-finished products in carbon, carbon-manganese fine grain (element combinations as stated, slabs to 2300mm wide, to 12000mm long to 54 tonnes for furtherprocessing to rolled products
Z25 & Z35 designations made be added for plates up to 35mm thick produced in the as rolled condition from concast slab for grades A, B and D with specifiedthrough thickness properties
Z25 & Z35 designations made be added for plates with specified through thickness properties for the approved grades in the normalised condition, normalisedrolled condition, TM condition and TM +Acc condition
Z25 & Z35 designations made be added for plates up to 40mm thick produced in the normalised rolled condition from concast slab for grades DH36 and DH32with specified through thickness properties
Certificate No. MD00/3489/0007/1 Expiry date: 15/12/2014
Materials Quality Scheme Approved - MQS 051
As belowB.O.S. / Con CastSteelmakingBENGANG STEEL PLATES CO., LTD. Daliancarbon, carbon-manganese 220SlabsSemi-FinishedA, B 20Normal StrengthHot Rolled CoilA, B 20Normal StrengthPlates from coils
No. 18, Gangtie Road, Pingshan DistrictBenxi City
Tel 0414 7827678 Fax: 0414 7827814 Email:[email protected] #: MD00/3311/0003/1 Expiry date: 28/01/2013
Liaoning Province
As belowB.O.S. / Con CastSteelmakingBENXI BEIYING IRON & STEEL (GROUP) CO., LTD. Daliancarbon, carbon-manganese 250SlabsSemi-Finishedcarbon, carbon-manganese 400BloomsA, B 20Normal StrengthHot Rolled Coil
BenXi CityLiaoNing Province
BeiTai Town, Pingshan District
Tel 0414 2529304 Fax: 0414 2529112 Email mailto:[email protected] #: MD00/3311/0003/1 Expiry date: 28/01/2013
Semi Finished products Carbon and Carbon-manganese, Fine Grain Al, slabs to 2100mm wide, to 9000mm long; Blooms to 400mm wide, to 12m long, for furtherprocessing for Rolled Products.
117017
A, B, D 14Normal StrengthSectionsCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinAH27S, AH32, AH36 14Higher Strength
Meili TownChangshu City
No. 9 Jusha Road
Tel: +86 0512 5206 1085 Fax: +86 0512 5266 1141 Email: mailto: [email protected] Web: http://www.lttg.cnCertificate #: MD00/3275/0003/1 Expiry date: 11/10/2012 #ENHANCED SURVEY#
Jiangsu Province 21551
As belowE.A.F. / Con CastSteelmakingCHANGSHU LONGTENG SPECIAL STEEL CO., LTD. JiangyinNormal Strength, Higher Strength 260BloomsSemi-FinishedA, B 20Normal StrengthSectionsAH27S, AH32, AH36 20Higher Strength
Tonggang Industrial Park,Meili Town, Changshu City,
118 Hualian Road,
Tel.:+86 512 5266 1284 Fax.: +86 512 52661284 Email: mailto: [email protected] Web: http://www.lttg.cnBlooms as semi finished products nominal 340mm width x nominal 12000mm length to the above maximum thickness are approved for further processing forrolled products.Certificate #: MD00/3976/0001/1 Expiry date: 08/12/2014
Jiangsu Province 215511
As belowB.O.S. / Con CastSteelmakingCISCO WuhanA, B, D 15Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 15Higher StrengthU1, U2, U3 100Chain Cable StockBars
Chongqing
Chongqing Iron and Steel Co., Ltd.Dadukou
Tel: +86 23 6884 2716 Fax: +86 23 6884 6465 Email: mailto:[email protected] Web: http://www.cqgt.comCertificate Number: MD00/0307/0009/1 Expiry: SUSPENDED
As at 06 November 2012 8Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingCISCO WuhanNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG 80
Changshou DistrictChongqing
Chongqing Iron and Steel Co., Ltd.Jiagnan Town (4100 Mill)
Tel: +82 623 6884 2716 Fax: +82 623 6884 9574 Email: [email protected] Web: http://www.cggfSlabs as semi finished products nominal 2500mm width x 12000mm length to the above maximum thickness are approved for further processing for rolledproducts.Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to Normal Strength Grades in the Normalised supplycondition and Normalizing Rolled supply condition.Plates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to Higher Strength Grades in the Normalised supplycondition and in the TM supply condition .Certificate Number: MD00/3763/0004/1 Expiry date: 29/03/2013
A, B, D, E 40Normal StrengthPlatesCISCO WuhanAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG
40Boiler & Pressure Vessel
Chongqing Iron and Steel Co., Ltd.Jiagnan Town (2700 Mill)Tel: +82 623 6887 3543 Fax: +82 623 6887 3543 Email: [email protected] Web: http://www.cggfPlates with specified through thickness properties may be accepted with the suffix Z25 or Z35 applied to all Grades and supply conditions.Certificate Number: MD00/3982/0002/1 Expiry: 26/01/2015
As belowE.A.F./Ingot/Con CastSteelmakingDAYE SPECIAL STEEL CO., LTD. Wuhancarbon, carbon-manganese 190StructuralBarscarbon, carbon-manganese, alloy 190MachineryU1, U2, API-2F 110Chain Cable StockU3, R4 160
Huangshi CityHubei Province
Tel: +86 714 6297888 Fax: +86 714 6297781Email: [email protected] #: MD00/2493/0005/1 Expiry date: 13/08/2014
Post code: 435001
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganeseE.A.F./Ingot/Con Castcarbon, carbon-manganese 5IngotsSemi-Finishedcarbon, carbon-manganese 280Blooms/Billetscarbon, carbon-manganese 200Barscarbon, carbon-manganese 200StructuralBarsU1, U2, U3 130Chain Cable Stock
Qiqihar CityHeilongjiang Province
BEIMEN SPECIAL STEEL CO., LTD.Fularji District
Tel: +86 452 6801920 Fax: +86 452 6801496 Email: mailto:[email protected] #: MD00/2907/0001/1 Expiry date: 30/07/2014
Carbon, Carbon-manganese, Alloy 27EAF/LRF/VD/IngotSteelmakingDONGBEI SPECIAL STEEL GROUP Daliancarbon, carbon-manganese, alloy 27IngotsSemi-Finished
Wanghua District,Fushun City,
FUSHUN SPECIAL STEEL CO. LTD.,East No 8 Anshan Road,
Tel No: +86 413 668 9161-3668 Fax no: +86 413 6674090Email: Web: www.dtsteel.comCertificate No MD00/3945/0001/1
Liaoning Province
As belowB.O.S. / Con CastSteelmakingFUJIAN PROVINCIAL SANSTEEL (GROUP) CO.,LTD.
Guangzhou
Normal strength, Higher Strength 250SlabsSemi-Finished
A, B 36Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36 30Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel
360, 410 36
As at 06 November 2012 9Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR OfficeMiddle Gongyezhong RoadMeilie District
Tel: +86 598 8205936 Fax: +86 598 8205138Email: [email protected] Web: www.fjsg.com.cnCertificate #: MD00/3587/0004/1 Expiry date: 27/04/2015
Sanming CityFujian Province
As belowB.O.S. / Con CastSteelmakingGUANGXI LIUZHOU GuangzhouA, B 36Normal StrengthPlatesAH27S, AH32, AH36 36Higher StrengthA, B 12Normal StrengthHot Rolled Coil
117 BeiqueLiuzhou
IRON & STEEL (GROUP) COMPANY
Tel: +86 (0)772 2592132 Fax: +86 (0)772 2592784 Email mailto:[email protected] Web http://www.liuzousteel.comCertificate #: MD00/2632/0006/1 Expiry date: 02/01/2015
Guangxi
As belowB.O.S. / Con CastSteelmakingHANBAO IRON & STEEL CO. LTD (HANSTEELGROUP)
Wuhan
As below 250SlabsSemi-Finished
A, B, D 18Normal StrengthHot Rolled Coil
AH27S, AH32, AH36, DH27S, DH32, DH36 18Higher Strength
A, B, D 18Normal StrengthPlates from coils
AH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength
232,Fuxing Road,Handan,
Tel +86 310 2093287 Fax No. + 86 310 2093606
Certificate No MD00/3874/0001/ 1 Expiry Date 10/01/2014
Hebei. 056015
As belowB.O.S. / Con CastSteelmakingHEBEI IRON & STEEL CO., LTD. WuhanAs belowSlabsSemi-FinishedAs belowBlooms/BilletsA, B, D, E 50Normal StrengthPlatesAH27S, DH27S, EH27S 38Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 50360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50
Handan CityHebei Province
Handan Branch232 Fuxing Road
Tel: +86 310 6072202 Fax: +86 310 6074661Email mailto:[email protected]
Certificate #: MD00/1970/0007/1 Expiry date: 05/03/2013
056015
As belowB.O.S. / Con CastSteelmakingHEBEI IRON & STEEL GROUP DalianA, B 150BilletsSemi-Finished
The West Side of Qianan Railway StationQianan City
YANSHAN IRON & STEEL Co., Ltd.
Tel: +86 315 7769 566 Fax: +86 315 7769 566
Certificate #: MD00/3648/0002/1 Expiry date: 08/06/2015
Hebei Province (064403)
As below 220B.O.S. / Con CastSteelmakingHEBEI JINGYE CUT DEAL CO. LTD., DalianNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D 30Normal StrengthPlatesAH27S, AH32, AH36, DH32, DH36 30Higher Strength
Pingshan CountyShijiazhuang City
Nandian Town
Tel No +86 311 8287 3953 Fax No +86 311 82873988 Mob +86 158 3111 8888Email [email protected] www.hbjyjt.comCertificate No MD00/4022/0001/1 Expiry Date 09/05/2015
Hebei Province
As at 06 November 2012 10Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingHEBEI JITAI SPECIAL STEEL GROUP CO., LTD. DalianA, B, D 20Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher StrengthA, B 38Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength
Lincheng CountyXingtai City
Feng Village
Tel +86 319 7018893 Fax +86 319 3033326 Email: mailto:[email protected] Web: htpp://www.jitaichina.cnCertificate #: MD00/3116/0007/1 Expiry date: 07/11/2013
As belowE.A.F. / Con CastSteelmakingHENGYANG VALIN STEEL TUBE CO., LTD. Wuhancarbon, carbon-manganese 330BilletsSemi-Finished
Hengyang CityHunan Province 421001
No. 10 Dalixincun
Tel: +86 734 8872311 Fax: +86 734 8872322 Web: www.hysteeltube.com
Certificate #: MD00/3098/0001/1 Expiry date: 06/08/2013
As belowB.O.S. / Con CastSteelmakingHUNAN VALIN LIANYUAN STEEL CO., LTD. Wuhancarbon, carbon-manganese 230SlabsSemi-FinishedA, B, D 25Normal StrengthHot Rolled CoilA, B, D 25Normal StrengthPlates from coils
Huangnitang, LoudiHunan Province
Tel +738 8661473 Fax +7388663570Email: [email protected]: www. lysteel.comCertificate #: MD00/3999/0001/ Expiry date: 06/03/2015
Post Code: 417009
A, B 12Normal StrengthSectionsJIANGMEN XINHUI YILI SECTION STEEL MILLCO., LTD.
Guangzhou
Xinhui CityGuangdong Province
Xinhui Shuangshui Industry Development Zone
Tel: +86 750 6417718 Fax: +86 750 9417728Certificate #: MD00/2842/0004/1 Expiry date: 07/11/2013
Post zip: 529153
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP NanjingAs belowE.A.F. / Con Castcarbon, carbon-manganese 200Blooms/BilletsSemi-Finishedcarbon, carbon-manganese 100StructuralBarscarbon, carbon-manganese 92MachineryU2, U3 100Chain Cable Stock
Huai'an CityJiangsu Province
HUAIGANG SPECIAL STEEL CO., LTDNo. 53 Huagong Road
Tel +81 517 83036135 Fax +81 517 83631344 Email mailto:[email protected]
Certificate #: MD00/3240/0002/1 Expiry date: 14/06/2012
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished
Jinfeng TownZhangjiagang City
Hongfa Steel PlantSteelmaking Plant Number 1
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: [email protected] Web http://www.sha-steel.comApproval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.Certifcate Number: MD00/3127/0006/1 Expiry date: 28/10/2013
Jiangsu Province 215625
A, B, D, E 60Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH27S,FH32, FH36, FH40
60Higher Strength
360AR, 410AR, 460AR, 360FG, 410FG, 460FG,490FG, 510FG
40Boiler & Pressure Vessel
Hongfa Steel PlantSteel Plate Mill Line No. 1
Tel +86 0512 58568791 Fax: +86 0512 58550818 Email: mailto:[email protected] Web: http://www.sha-steel.com Plates in Grades A and B Fine Grain Al+Ti in the Normalising Rolled condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to60.0mm.Plates in Grades D and E Fine Grain Al+Ti+Nb in the TM+Acc condition maximum thickness 60.0mm are restricted to the thickness range 40.0 to 60.0mm.Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.Certificate No. MD00/3388/0005/1 Expiry date: 28/10/2013
Jiangsu Province, 215625
As at 06 November 2012 11Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 60Normal StrengthPlatesJIANGSU SHAGANG GROUP CO., LTD JiangyinAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH27S,FH32, FH36, FH40
60Higher Strength
360AR, 410AR, 460AR, 360FG, 410FG, 460FG,490FG, 510FG
40Boiler & Pressure Vessel
Hongfa Steel PlantSteel Plate Mill LIne No. 2Tel +86 0512 5856 8800 Fax: +86 0512 5855 0818 Email: mailto:[email protected] Web: http://www.sha-steel.com Plates in the Normalizing Rolled are restricted to a maximum width of 4650mm condition and in the TM+Acc condition are restricted to a maximum width of4150mm.Plates in the Normalizing Rolled condition and the TM+Acc condition are restricted to a maximum width of 4150mm.Certificate No. MD00/3913/0003/1 Expiry date: 25/05/2014
As belowB.O.S. / Con CastSteelmakingJIANGSU SHAGANG GROUP CO., LTD Jiangyincarbon, carbon-manganese 320SlabsSemi-Finished
Hongfa Steel PlantSteelmaking Plant Number 2
Tel: +86 512 5856 8791 Fax: +86 512 5855 8900 Email mailto: [email protected] Web http://www.sha-steel.comApproval covers for con cast slabs to nominal sizes 2065mm wide x 9000mm long to the above maximum thickness for further processing for rolled products.Certifcate Number: MD00/3127/0005/1 Expiry date: 24/05/2014
Jiangsu Province 215625
As belowE.A.F. / IngotSteelmakingJIANGSU SUNAN SPECIAL EQUIPMENT GROUPCO., LTD.
Jiangyin
carbon, carbon-manganese, alloy 24IngotsSemi-Finished
TONGGANG ROADCHANGSHU
BAIDANGQIAO
Tel: +86 512 5263 1888 / 1908 Fax: +86 512 5263 7910 email: [email protected] Web: http://snzbjt.comIngots as semi finished products nominal 1170/1290mm diameter x nominal 3000mm long to the above maximum weight are approved for further processingfor forgingsCertificate Number: MD00/3583/0002/1 Expiry: 01/11/2012
JIANGSU
A, B 30Normal StrengthSectionsJIANGYIN BOFENG IRON & STEEL CO., LTD. JiangyinAH27S, AH32 30Higher Strength
Huaxicun Industrial ZoneJiangyin City
Tel: +86 510 8621 7672 Fax: +86 510 8621 7672 Email: [email protected] Web: http://www.bofengsteel.cnThe approved sections are in the form of universal flats nominal widths <600mm to the maximum thickness shown above.Certificate Number: MD00/4031/0001/1 Expiry: 06/06/2015
Jiangsu Province
A, B 25Normal StrengthPlatesJIANGYIN CHANGDA STEEL CO., LTD. JiangyinNo. 388, West Binjiang Road,Jiangyin City,
Tel: +86 510 8603 2250 Fax: +86 510-8603 2250 Email: [email protected] Web: http:// www.chdsteel.comPlates are restricted to a maximum width of 2200mm.Certificate Number: MD00/3975/0001/1 Expiry date: 03/11/2014
Jiangsu Province, 214442,
As belowE.A.F. / IngotSteelmakingJIANGYIN HUAQIANG SPECIAL STEEL Jiangyincarbon, carbon-manganese, alloy 32IngotsSemi-Finished
No. 18, Biangang Road,Huaxi, Jiangyin City,
CASTING & FORGING THERMOELECTRIC CO., LTD.
Tel: +86 510 860 60566 Fax: +86 510 860 60512 Email: [email protected] Web: http://www.jyhuaqing.comIngots as semi finished products nominal 1240mm/1320mm diameter x 2770mm long to the above maximum weight are approved for further processing forforgings.Certificate Number: MD00/4013/0001/1 Expiry: 23/04/2015
Jiangsu Province, 214421,
As BelowB.O.S./E.A.F./Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
Normal strength 250SlabsSemi-Finished
carbon, carbon-manganese, alloy 900Semi-finished ProductsBars
carbon, carbon-manganese, alloy 180Structural
carbon, carbon-manganese, alloy 180Machinery
R3, R3S, R4 160Chain Cable Stock
U1, U2, U3 180
As at 06 November 2012 12Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office297, Bin Jiang East RoadJiangyin City
Tel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:[email protected] Web: http://www.jyxc.comSlabs as Semi-Finished Products to the above maximum thickness, nominal 2600mm width and nominal 12000mm length are approved for further processing forrolled products.Bars as Semi-Finished Products in the As Cast condition to maximum diameter as stated grades are accepted for further processing for forgings.Alloy Grade Bars as Semi-Finished Products in the As Rolled condition to maximum diameter of 280mm are accepted for further processing for forgings.Alloy grade bars as Semi-finished Products are accepted for approved applications, Grade 34Mn2V to 230mm maximum diameter for further processing for gascylinders (Normalised heat treatment required), Grade 42CrMo to 300mm maximum diameter for further processing for marine structural applications(Quenched and Tempered heat treatment required).Bars for mooring chain cable grades are supplied to the following specifications;R3 - R30Mn2, R3S - 28MnCrMo, R4 - 22MnCrNiMo.The supply of mooring grade chain cable bars is restricted to the following sizes for the detailed chain manufacturers;Zhenjiang Anchor Chain Factory - Grades R3 and R3S to 105mm diameter, Grade R4 to 160mm diameter.Jiangsu Asian Star Anchor Chain Cable Co. Ltd - Grades R3 and R3S to 160mm diameter, Grade R4 to 135mm diameter.Liawu Steel Zibo Anchor Chain Cable Co. Ltd Qingdao Branch - Grades R3, R3S and R4 to 114mm diameter. Foshan Marine Anchor Chain Ltd - Grade R3S to 130mm diameter.Certificate #: MD00/2306/0013/1 Expiry date: 26/09/2013
Jiangsu province 214429
As belowB.O.S. / Con CastSteelmakingJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
Normal strength, Higher Strength 300SlabsSemi-Finished
A, B, D, E 50Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 50
3500 Plate Mill
Tel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:[email protected] Web: http://www.jyxc.comPlates supplied in the Normalizing Rolled condition are restricted to 3100mm width.Z35 designation for through thickness properties may be added to plates supplied in the normalized condition.Slabs as semi finished products are approved for further processing for rolled products, nominal 3200mm wide x 15,000mm long to the maximum thicknessshown above.Certificate Number: MD00/3857/0003/1 Expiry date: 08/11/2013
Jiangsu Province 214429
A, B, D, E 80Normal StrengthPlatesJIANGYIN XINGCHENG SPECIAL STEEL WORKSCO., LTD.
Jiangyin
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 80
4300 Plate MillTel: +86 510 6193388-6165 Fax: +86 510 6195042 Email: mailto:[email protected] Web: http://www.jyxc.comPlates in the Normalizing Rolled and Thermomechanical supply conditions are restricted to 3800mm maximum width. Z35 designation for through thickness properties may be added to all plates in the above supply conditions.Certificate Number: MD00/xxxx/0001/1 Expiry date: 10/01/2015
As belowB.O.S. / Con CastSteelmakingJINAN IRON AND STEEL CO., LTD. Qingdaocarbon, carbon-manganese 270SlabsSemi-FinishedE 50Normal StrengthPlatesA, B, D 60AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH32,FH36, FH40
60Higher Strength
360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60A, B 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36 12Higher Strength
Jinan, 250101Shandong Province
21, Gongye Bei Road
Tel +86 531 8868029 Fax +86 531 8982126 Email: [email protected] Web:http://www.jigang.com.cnCertificate #: MD00/0799/0012/1 Expiry date: 16/10/2013
304L, 316L 80Austenitic StainlessPlatesKUNSHAN DAEKYUNG STAINLESS STEEL CO.,LTD
Shanghai Port
Kunshan Economy Technology Development ZoneKunshan
No. 66 Longdeng Road
Tel:+86 512 57900998 Fax: +86 512 57700372Email: [email protected] #: MD00/3479/0002/1 Expiry date: 08/06/2014
Jiangsu Province
As at 06 November 2012 13Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingLAIWU STEEL GROUP LTD. YINSHAN SECTIONSTEEL CORPORATION
Qingdao
carbon, carbon-manganese 300BilletsSemi-Finished
A, B, D 60Normal StrengthPlates
AH32, AH36, DH32, DH36 60Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 60
No. 1, Zhagangdajie, Xinxing RoadGangcheng District
Tel: +86 634 6821211 Fax: +86 634 6820824 Certificate #: MD00/3855/0001/1 Expiry date: 07/11/2013
Laiwu City, Shangdong
As belowB.O.S. / Con CastSteelmakingMAANSHAN IRON & STEEL COMPANY LIMITED NanjingA, B 25Normal StrengthPlatesAH32, AH36, DH32, DH36 25Higher Strength360AR, 410AR 25Boiler & Pressure Vessel
No.8 Hongqi Road (N)Maanshan City
Tel: +86 555 2886 904 Fax: +86 555 2886 904 Email: mailto:[email protected] http://www.magang.com.cnCertificate #: MD00/0965/0006/1 Expiry date: 09/10/2012
Anhui Province PC:243000
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingMAANSHAN IRON & STEEL COMPANY LIMITED Nanjingcarbon, carbon-manganese, alloy 23IngotsSemi-Finished
Yushan District
HEAVY MECHANICAL EQUIPMENT COMPANYSantai Road
Tel No +86 555 2887961 Fax +86 555 2887961Email [email protected] www.magang.com.cnCertificate No. MD00/3369/0002/1 Expiry date: 05/09/2013
Anhui Province 243000
As belowB.O.S. / Con CastSteelmakingMINMETALS YINGKOU MEDIUM PLATE CO., LTD. DalianNormal strength, Higher Strength 250SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH27S, DH27S, EH27S 40Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 50360AR, 410AR 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50
Laobian DistrictYingkou City
No 1 Fanrong Road, Yejin Street
Tel: 086 (0)417 3256051 Fax: 086 (0)417 3256057 Email mailto:[email protected] :www.wkyg.comPlates with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2585/0006/1 Expiry date: 15/09/2014
Liaoning Province
As belowB.O.S. / Con CastSteelmakingNANJING IRON & STEEL CO., LTD. NanjingAs belowE.A.F. / Con CastNormal strength, Higher Strength 220SlabsSemi-FinishedNormal Strength, Higher Strength 320BloomsNormal Strength, Higher Strength 150BilletsA, B, D, E 60Normal StrengthPlatesAH40, DH40, EH40, FH27S, FH32, FH36, FH40 40Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
60
360AR, 410AR, 360, 410 25Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60U1, U2, U3 180Chain Cable StockBars
As at 06 November 2012 14Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
XieJiaDianLiuhe District
Nanjing Works
Tel: +86 25 570 74341 Fax: +86 25 57793425 EMail mailto:[email protected] Web:http://www.nisco.com.cnPlates with specified through thickness properties may be accepted with the suffix Z35 applied to all approved grades of normal and higher strength steels.Chain cable stock in Grades U2 and U3 is intended for further processing with quenched and tempered heat treatment, bars at 80mm diameter or less areproduced by BOS or EAF steelmaking, bars over 80mm diameter are produced by EAF steelmaking.Billets and blooms as semi finished products to the above maximum thickness, nominal to 480mm width and to nominal 12000mm length are approved forfurther processing for rolled products.Slabs as semi finished products to the above maximum thickness, nominal to 2510mm width and to nominal 4000mm length are approved for further processingfor rolled products.Certificate Number: MD00/1065/0013/1 Expiry date: 12/10/2013
Nanjing, Post Code: 210035
As belowB.O.S./Ingot/Con CastSteelmakingNANYANG HANYE SPECIAL STEEL CO., LTD., Wuhancarbon, carbon-manganese, alloy 48IngotsSemi-Finishedcarbon, carbon-manganese, alloy 300SlabsA, B, D 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 100Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel
Xixia County,Nanyang City,
Huiche Town Industry Area,
Tel No: +86 377 697 65211 Fax No: +86 377 697 65333Email: [email protected]: www.elongcheng.comCertificate No: MD00/3969/0001/1 Expiry date 02/01/2015
Henan Province
See notesB.O.S. / Con CastSteelmakingPANGANG GROUP PANZHIHUA STEEL &VANADIUM CO. LTD.,
Wuhan
See notesSlabsSemi-Finished
See notesBillets
Panzhihua City,Sichuan Province,Tel No: +86 0812 339 1756 Fax No: +86 0812 339 6014Email: [email protected]: wwwpzhsteel.com.cnCertificate No. MD00/4036/0002/1 Expiry 02/06/2015
As BelowB.O.S./E.A.F./IngotSteelmakingPENGZHOU SANXIN MACHINERYMANUFACTURE Co. Ltd.
Wuhan
carbon, carbon-manganese, alloy 9IngotsSemi-Finished
Pengzhou CitySichuan Province
Sanyi
Tel: +86 28 83773044 fAX: +86 28 83773071Certificate #: MD00/3106/0003/1 Expiry date: 01/10/2013
P.C 611934
E 32Normal StrengthPlatesQINHUANGDAO SHOUGANG PLATE MILL CO.,LTD.
Dalian
A, B, D 35
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
32Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 32Boiler & Pressure Vessel
360AR, 410AR 35
No. 409 Jianshe StreetQinhuangdao City
Tel: +86 010 88296326 Fax: +86 010 88291295 email: mailto: [email protected] #: MD00/2097/0008/1 Expiry date: 05/07/2015
Hebei Province
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingQINHUANGDAO SHOUQIN METAL MATERIALSCO., LTD.
Dalian
carbon, carbon-manganese 250SlabsSemi-Finished
D 50Normal StrengthPlates
A, B 100
AH40 40Higher Strength
DH40, EH27S, EH32, EH36, EH40 50
AH36, DH27S, DH36 80
As at 06 November 2012 15Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
China, People's Republic of 80Higher StrengthPlatesCO., LTD.
AH27S, AH32, DH32 100
360AR, 410AR 16Boiler & Pressure Vessel
360, 410 32
510FG 80
360FG, 410FG, 460FG, 490FG 100
Funing CountyQinhuangdao
Duzhuang
Zip 066326 Tel +86 010 88296326 Fax +86 010 88291295 Web http://www.shouqin.com.cn
All plate grades and thicknesses with through thickness properties, notations Z25 and Z35 may be added.
Certificate #: MD00/3136/0006/1 Expiry date: 06/02/2014
As belowB.O.S. / Con CastSteelmakingRIZHAO STEEL WIRE CO., LTD Qingdaocarbon, carbon-manganese 230SlabsSemi-FinishedA, B 25Normal StrengthHot Rolled CoilA, B 25Normal StrengthPlates from coils
No. 600, Yanhai Road, RizhaoShangdongTel: +86 633 6188656 Fax: +86 633 6188910 Certificate #: MD00/3102/0002/FW Expiry date: 08/10/2010
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingSGIS SONGSHAN CO., LTD Guangzhoucarbon, carbon-manganese, alloy 270SlabsSemi-Finishedcarbon, carbon-manganese, alloy 170BilletsA, B, D, E 60Normal StrengthPlatesAH40, DH40, EH40 36Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
60
360AR, 410AR 20Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60
Qujiang DistrictShaoguan City
Tel: +86 (0)751 878 5354 Fax: +86 (0)751 878 6066 Email mailto:[email protected] #: MD00/2175/0008/1 Expiry date: 23/11/2012CEV is limited to a maximum of 0.45% for as rolled and nomalised higher strength steels but does not apply to TM steels
Guangdong 512123
As belowB.O.S. / Con CastSteelmakingSHANDONG SHOUGUANG JUNENG SPECIALSTEEL CO, LTD.
Qingdao
carbon, carbon-manganese 130StructuralBars
carbon, carbon-manganese 130Machinery
U1, U2, U3 130Chain Cable Stock
No. 9 Tegang RoadShouguang, Shangdong Province
Tel +86 532 5186057 Tel+86 532 5186789Certificate #: MD00/3260/0004/1 Expiry date: 22/09/2015
262711
Carbon, Carbon-manganese, Alloy 200EAF/LRF/VD/IngotSteelmakingSHANGHAI HEAVY MACHINERY PLANT CO.,LTD.
Shanghai Port
Minhang DistrictShanghai
1800 Jiangchuan Road
Tel: +86 21 54724065ext 2027 Fax: +86 21 54721007 Email mailto:[email protected] Web http://www.shmp.sh.comIncluding ingots Certificate #: MD00/1345/0001/1 Expiry date: 25/07/2014
200245
As belowE.A.F./A.O.D./Con CastSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. Dalian304L, 316L 20Austenitic StainlessPlatesUNS S31803 20Duplex Stainless
As at 06 November 2012 16Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Jiancaoping Street No. 2Taiyuan030003Taiyuan
Stainless Steel Hot Rolling Mill
Tel No: +86 351 3012029 Fax No: +86 351 3017893 Mob: 13503502921Email: [email protected] Web: http://tgbx.tisco.com.cn Certificate No. MD00/3185/0006/1 Expiry date: 18/08/2014
As belowB.O.S. / Con CastSteelmakingSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianNormal strength, Higher Strength 200SlabsSemi-FinishedA, B, D 25Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength360FG, 410FG 25Boiler & Pressure VesselA, B, D 25Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 25Higher Strength410 FG, 360 FG 25Boiler and Pressure Vessel
Jiancaoping Street No. 2Hot Strip Mill
Tel: +86 351 3012029 Fax: +86 351 3017893 Email: [email protected] Web: http: //tgbx.tisco.com.cn Slabs as semi finished products 2310mm nominal width and 12000mm nominal length to the above maximum thickness are approved for further processing forrolled products.Certificate #: MD00/3507/0002/1 Expiry date: 30/07/2014
A, B, D 40Normal StrengthPlatesSHANXI TAIGANG STAINLESS STEEL CO., LTD. DalianAH32, AH36, DH32, DH36 40Higher Strength304L, 316L, 304*, 316* 40Austenitic StainlessUNS S31803 40Duplex Stainless
Qiaodong Street No.3Linfen City
Linfen Heavy Plate Mill
Tel: +86 351 3017667 Fax: +86 351 3017893 Email: [email protected] Web: http:// www.tisco.com.cn Certificate No MD00/3688/0004/1 Expiry date 07/07/2015
Shanxi Province
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingSHIJIAZHUANG I & S CO., LTD. Daliancarbon, carbon-manganese 150StructuralBarscarbon, carbon-manganese 150MachineryU1, U2, U3 150Chain Cable Stock
Shijiazhuang CityHebei Province
No. 363 Heping E Road
Tel: +86 (0)311 86913304 Fax: +86 (0)311 86913368Email: [email protected] #: MD00/3315/0002/1 Expiry date: 07/12/2013
As belowB.O.S. / Con CastSteelmakingSHOUGANG JINGTANG UNITED IRON & STEELCO., LTD.
Dalian
carbon, carbon-manganese 250SlabsSemi-Finished
A, B, D 18Normal StrengthHot Rolled Coil
AH32, AH36, DH32, DH36 18Higher Strength
A, B, D 18Normal StrengthPlates from coils
AH32, DH32, AH36, DH36 18Higher Strength
Caofeidian Industrial Zone, Tangshan
Tel: +86 315 8872636 Fax: +86 315 8872606 Email: mailto:[email protected] #: MD00/3820/0001/1 Expiry date: 21/11/2013
Post Code: 063200
As belowB.O.S. / Con CastSteelmakingSHOUGANG QIAN'AN IRON & STEEL CO., LTD.,HEBEI
Dalian
carbon, carbon-manganese, alloy 230SlabsSemi-Finished
A, B, D 18Normal StrengthHot Rolled Coil
AH27S, AH32, AH36, DH27S, DH32, DH36 18Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 18Boiler & Pressure Vessel
A, B, D 18Normal StrengthPlates from coils
AH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength
As at 06 November 2012 17Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Yang-dian-zi TownQian'an
Binhe Village
Tel: +86 315 7703138 Fax: +86 315 7703139 Email: mailto:[email protected] wwwsgqg.comCertificate #: MD00/3488/0003/1 Expiry date: 09/07/2014
Hebei, 064404
A, B, D 18Normal StrengthPlates from coilsSINOSTEEL (TIANJIN) STEEL PROCESSING CO.LTD DalianAH27S, DH27S, AH32, DH32, AH36, DH36 18Higher Strength
Xin Xing Village,Dongli District,
No 700 Hexing Road
Tel No 0086 22 24982876 Fax No. 0086 22 24981723Email [email protected] tianjin.sinosteel.comCert No. MD00/3656/0002/1 Expiry date: 08/07/2015Not approved for heat treatment
Tianjin
As belowE.A.F. / IngotSteelmakingSPECIAL STEEL BRANCH OF Wuhancarbon, carbon-manganese, alloy 8IngotsSemi-Finished
Baotou CityInner Mongolia
INNER MONGOLIA NORTH HEAVY INDUSTRIES GROUP CORP LBinggong Road, Qingshan District
Including semi-finished as-forged bars to 8.5 tonnes in carbon, carbon-manganese and alloy steel for further process of forge
Tel: +86 0472 338 6106Fax: +86 0472 332 2346Certificate #: MD00/3099/0004/1 Expiry date: 08/08/2013
014033
A, B 15Normal StrengthSectionsSUQIAN NANJING IRON & STEEL NanjingAH32, AH36 15Higher Strength
No.89 Jingshan Road,Suyu District,
JINXIN STEEL ROLLING Co., Ltd.
Tel; +86 527 844 53907 Fax: +86 527 844 80094 Email: [email protected]: MD00/3741/0002/1 Expiry date: 17/12/2014
Suqian City, Jiangsu,
As belowE.A.F. / Con CastSteelmakingSUZHOU SUXIN SPECIAL STEEL CO., LTD. Shanghai PortU1, U2, U3 120Chain Cable StockBars
Huashan, Tong An, SuzhouJiangsu
Tel: +86 0512 8887 7088 Fax: +86 0512 88877815Certificate #: MD00/3492/0002/1 Expiry date: 14/07/2014
Post Code: 215151
As below, carbon, carbon-manganeseE.A.F. / IngotSteelmakingTAI YUAN HEAVY INDUSTRY CO. LTD. Wuhancarbon, carbon-manganese 36IngotsSemi-Finished
No.53, Yuhe Street,Wan Bailin Dristrict, Taiyuan City,
Tel +86 351 636 6770 Fax: +86 351 636 6750Email: [email protected]: www.tyhi.com.cnCertificate #: MD00/3412/0002/1 Expiry date: 03/10/2013
Shanxi Province, 030024,
As belowB.O.S. / Con CastSteelmakingTANGSHAN HEAVY PLATE CO., LTD. Daliancarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
Leting County,Tangshan City,
Lingang Industrial Park
Tel No: +86 315 4958304 Fax No: +86 315 4959038Email [email protected]
Certificate #: MD00/3475/0003/1 Expiry date: 01/06/2014
Hebei
A, B 14Normal StrengthSectionsTANGSHAN XINXIN SPECIAL STEEL CO. LTD DalianAH32, AH36 14Higher Strength
As at 06 November 2012 18Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Bencheng Town, Luannan CountyTangshan City
No. 95 Middle Street
Tel: +86 0315 412 5016; Fax: +86 0315 412 5016Email:mailto: [email protected]: www.xxtg.cnCertificate #: MD00/3468/0004/1 Expiry date: 18/05/2011
Hebei Province
As belowB.O.S. / Con CastSteelmakingTIANJIN IRON AND STEEL GROUP CO. LTD. Daliancarbon, carbon-manganese, alloy 250SlabsSemi-FinishedA, B, D 38Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength
Dongli DistrictTianjin
398 Jintang Road
Tel:+86 22 24706052 Fax: +86 22 24706052 Email: mailto:[email protected]: www.tgsteel.comCertificate #: MD00/3485/0003/1 Expiry date: 02/07/2014
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingTIANJIN PIPE (GROUP) CORPORATION Daliancarbon, carbon-manganese 310Blooms/BilletsSemi-Finished
Jintang Road
Tel:+86 22 24802227 Fax: +86 22 24801291Certificate #: MD00/3361/0002/1 Expiry date: 29/07/2013
300301
A, B 15Normal StrengthSectionsTIANJIN YONGHENG ENTERPRISE CO., LTD. DalianAH32, AH36 15Higher Strength
Daqiuzhuang Town Industrial ZoneTel:+86 (0)2228899290 Fax: +86(0)2260730999 Email:mailto:[email protected] Web:http://www.tjyhsy.comCertificate #: MD00/3953/0001/1 Expiry date: 25/09/2014
carbon, carbon-manganese, alloy 70E.A.F. / IngotSteelmakingTONGYU HEAVY INDUSTRY Co., Ltd Qingdaocarbon, carbon-manganese, alloy 70IngotsSemi-Finished
Dezhou City,Shandong Province,
High & New Technology Industry Development Zone,Yucheng City,
Tel: +86 534 7520690 Fax: +86534 7521470Certificate No. MD00/3998/00001/1 Expiry date:01/03/2012
As belowB.O.S. / Con CastSteelmakingWISCO WuhanA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50A, B, D 25Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 25Higher Strength360, 410 12Boiler & Pressure Vessel
QingshanWuhan
Wuhan Iron and Steel Co., Ltd.Changqian
Tel: +86 27 8689 8489 Fax: +86 27 8689 3482E-mail: Mailto: [email protected] Web: http://www.wisco.com.cnCertificate #: MD00/1683/0009/1 Expiry date: 21/11/2013
As belowB.O.S. / Con CastSteelmakingWISCO ECHENG IRON & STEEL CO., LTD. WuhanAs below, Normal strength, Higher Strength 300SlabsSemi-FinishedA, B, D 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 50Boiler & Pressure Vessel
Wuchang Dadao No. 105Ezhou City
Tel: +86 711 3233225 Fax: +86 711 3233225 Email mailto: [email protected] #: MD00/3931/0002/1 Expiry date: 05/07/2014
Hubei Province
carbon, carbon-manganese, alloy 100IngotsSemi-FinishedWUHAN HEAVY INDUSTRY Wuhan
Quingshan DistrictWuhan
CASTING AND FORGING CO., LTD.1 Wudong Street
Tel No: +86 027 6886 1813 Fax No: +86 027 6886 1810Email [email protected] www.whzg.com.cnCertificate No: MD00/1681/0001/1 Expiry date: 05/07/2014
Hubei
As at 06 November 2012 19Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F./Ingot/Con CastSteelmakingWUYANG IRON & STEEL COMPANY LTD. WuhanA, B, D, E 150Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
Henan ProvinceP.N: 462500
Wugang City
Tel: +86 375 811 1230 Fax: +86 375 811 4006Plates with specified through thickness properties in listed grades of normal and higher strength steels.Certificate #: MD00/2044/0008/1 Expiry date: 14/07/2014
A, B, D, E 100Normal StrengthPlatesWUYANG IRON & STEEL COMPANY LTD. WuhanFH32, FH36, FH40 50Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
100
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure Vessel
Wugang City,Henan Province,
Wuyang New Wide and Heavy Steel Plate Co Ltd
Tel No. +86 375 8111230 Fax No. +86 375 8114006 Email to: [email protected] with specified through thickness properties in listed grades of normal and higher strength steelsCertificate No. MD00/3714/0002/1 Expiry Date 14/07/2014
PN 462500
Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingXINING SPECIAL STEEL CO., LTD. Wuhancarbon, carbon-manganese, alloy 12IngotsSemi-Finishedcarbon, carbon-manganese, alloy 18ESR Ingotscarbon, carbon-manganese, alloy 250Semi-finished ProductsBars
No. 52 Chaidamu West RoadXining
Tel: 0086 0971 529 9407 Fax: 0086 0971 529 9248 Email: [email protected]: www.xntg.comCertificate #: MD00/3093/0006/1 Expiry date: 11/06/2013
Qinghai
See notesB.O.S. / Con CastSteelmakingXINYU IRON & STEEL CO. LTD. WuhanSee notesE.A.F. / Con Castcarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesFH27S, FH32, FH36, FH40 50Higher StrengthAH27S, DH27S, DH40, EH27S, EH40 60AH32, AH36, DH32, DH36, EH32, EH36 80360AR, 410AR 20Boiler & Pressure Vessel360, 410 60360FG, 410FG, 460FG, 490FG, 510FG 80A, B 14Normal StrengthSectionsAH27S, AH32, AH36 14Higher Strength
Xinyu CityJiangxi Province 338001
1 Yejin Road
Tel: 0790 629 4433 Fax: 0790 629 3826 Email: [email protected]: www.xinsteel.com.cnAll grades with specified through thickness properties, designation to Z35 may be addedCertificate #: MD00/3093/0007/1 Expiry date: 11/06/2013
As belowB.O.S. / Con CastSteelmakingXISC - HUNAN VALIN XIANGTAN Wuhancarbon, carbon-manganese, alloy 300SlabsSemi-FinishedA, B, D, E 60Normal StrengthPlatesAH40, DH40, EH40, FH40 40Higher StrengthFH27S, FH32, FH36 60AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTAH40, LTDH32, LTDH36,LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,LTFH36, LTFH40
40Ferritic Low Temperature
Xiangtan City,Hunan Province,
IRON & STEEL CO., LTD.Yuetang District,
Approved for Z25 & Z35 grades.
Tel +86 (0)731 5865 2130 Fax +86 (0) 731 58653050 Email mailto:[email protected] Web http://www.hnxg.com.cnCertificate #: MD00/3258/0007/1 Expiry date: 08/08/2015
As at 06 November 2012 20Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
austenitic stainlessB.O.S/V.O.D./Con CastSteelmakingYANTAI JIN CHENG PRECISION WIRE ROD CO.,LTD.
Qingdao
austenitic stainless steel 220Blooms/BilletsSemi-Finished
No. 2 Wuzhishan Road,Economic Technical Development Zone
Tel: +86 535 2166688 Fax: +86 535 2165008 Email:Jack_yen@walsinCertificate #: MD00/3992/0001/1 Expiry date: 21/02/2015
Yantai City, shandong Province
austenitic stainlessE.A.F. / IngotSteelmakingYONGXING SPECIAL STAINLESS STEEL CO LTD Shanghai Portaustenitic stainless 5IngotsSemi-Finishedaustenitic stainless 110Semi-finished ProductsBars
Yangjiabu,Huzhou City,
Tel No. +86 572 2350629 Fax No: +86 572 2351517Email: wang [email protected] : www.yongxingbxg.cnCertificate No. MD00/3791/0001/1 Expiry date 07/06/2013
Zhejiang Province
Carbon, Carbon-manganese, Alloy 16EAF/LRF/VD/IngotSteelmakingZHEJIANG TIANJI HEAVY INDUSTRY MACHINERYCO., LTD.
Shanghai Port
Fengqiao Town,Zhuji City,
No. 463 Busen Road,
Tel: +86 575 8704 1127 Fax: +86 575 8704 5392web: www.zhengtian.com.cnCertificate No. MD00/4069/0001/1 Expiry Date: 23/08/2015
Zhejiang Province,
austenitic stainless steelIF/AOD/Ingot/ConCastSteelmakingZHEJIANG TSINGSHAN IRON & STEEL CO.LTD. Ningboaustenitic stainless 3IngotsSemi-Finishedaustenitic stainless steel 240Blooms/Billetsaustenitic stainless 150Billets
Wenxi Town,Qingtian,
Xiaoshi Industry Zone
Tel No. 0086 578 6071 658 Fax No. 0086 578 6071 658Email [email protected] : www. zjqingshan.cnCert no. MD00/3673/0002/1 Expiry date: 25/08/2015
Zhejiang Province
As belowB.O.S. / Con CastSteelmakingZHONGPU (HANDAN) IRON AND STEEL CO.,LTD.
Dalian
A, B, D 38Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
Yangyi TownWuan City
No.1 Steel Making Plant
Tel: +86 (0)310-5178928 Fax: +86 (0)310-5178928 Web:http//www.hbpygt.com.cn Email: mailto:[email protected]: www.hbpygt.comCertificate #: MD00/3585/0002/1 Expiry date: 27/04/2015
Hebei Province, 056305
As belowB.O.S. / Con CastSteelmakingZHONGPU (HANDAN) IRON AND STEEL CO.,LTD.
Dalian
carbon, carbon-manganese 320SlabsSemi-Finished
A, B, D 38Normal StrengthPlates
AH27S, AH32, AH36, DH27S, DH32, DH36 38Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
Yangyi Town,Wuan City,
No.2 Steel Making Plant
Tel: +86 (0)310-5178900 Fax: +86 (0)310-5178928 Web:http//www.hbpygt.com.cn web: www.hbpygt.comCertificate #: MD00/4034/0001/1 Expiry date:10/06/2015
As at 06 November 2012 21Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Cuba
As belowE.A.F. / Con CastSteelmakingACINOX LAS TUNAS Havanacarbon, carbon-manganese 130BilletsSemi-Finished
Circuvalante Norte Km. 3 1/2CP75100
Tel: +53 131 46801 Ext 109 Fax: +53 131 46512 Email: [email protected] Web http://www.acinoxtunas.cuCertifcate: MD00/3698/0002/1 Expiry date: 23/05/2014
Las Tunas
Czech Republic
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingArcelorMittal Ostrava a.s. Praguecarbon, carbon-manganese 150SlabsSemi-Finishedalloy 180carbon, carbon-manganese, alloy 210BilletsA, B, D 14Normal StrengthSectionsA, B, D 60Normal StrengthBars
Vratimovská 689707 02 Ostrava-KunciceTel: +420 59 568 4213 Fax: +420 59 668 2275 Email: mailto:[email protected] Web http://www.arcelormittal.com/ostravaCertificate #: MD00/1123/0008/1 Expiry date: 12/12/2013
As belowB.O.S. / Con CastSteelmakingEVRAZ VITKOVICE STEEL, a.s. Praguecarbon, carbon-manganese 250SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselA, B, D, E 16Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
16Higher Strength
A, B, D, E 50Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength
709 00 Ostrava - HulvakyStramberska c.p. 2871/47
Tel: +420 59 595 5842 Fax: +420 59 595 7340 Email: mailto:[email protected] Web: http://www.vitkovicesteel.com
Approved for plates with specified through thickness properties (Z35) in all grades up to 50 mm thickness.
Semi-finished products in carbon and carbon-Manganese steels with fine grain: slabs to 1580mm wide to 8000mm long for further processing for rolled products
Materials Quality Scheme Approved - MQS 039Certificate #: MD00/1638/0013/1 Expiry date: 07/08/2013
PSC 709 00
As belowE.A.F. / IngotSteelmakingPILSEN STEEL s.r.o. Praguecarbon, carbon-manganese, alloy 200IngotsSemi-Finished
316 00 PlzenTylova 1/57
Tel: +420 378 134 225 Fax: +420 378 132 058Email: [email protected]: www.pilsensteel.cz Certificate # MD00/1383/0005/1 Expiry date: 24/03/2014
carbon, carbon-manganese, alloy 300StructuralBarsSOCHOROVÁ VÁLCOVNA TZ, a.s. Praguecarbon, carbon-manganese, alloy 300Machinery
272 01 Kladno-DrinTel No +420 558 536 065 Fax No. +420 558 534 926Email [email protected] www.trz.czMachinery grade bars with the maximum diameter of 300 mm produced from con-cast blooms may be accepted with a minimum rolling reduction of 3:1.Certificate #: MD00/2955/0005/1 Expiry date: 21/02/2015
As belowB.O.S./Ingot/Con CastSteelmakingTRINECKE ZELEZARNY, a.s. PragueAs belowE.A.F./Ingot/Con Castcarbon, carbon-manganese 140SlabsSemi-Finishedcarbon, carbon-manganese 525BarsA 50Normal StrengthSectionscarbon, carbon-manganese, alloy 90MachineryBarsU1, U2 72Chain Cable Stock
Prumyslova 1000CZ-739 70 Trinec - Stare MestoTel: +420 558 533 010 Fax: +420 558 533 306 Email: mailto:[email protected] Web hppt://www.trz.czApproval for Slabs as semi finished products are for further processing for rolled products, nominal sizes are 240mm wide x 12000mm long to the abovemaximum thickness.Approval for Bars as semi finished products are for further processing for tube production, nominal length 1200mm to the above maximum diameter.Certificate #: MD00/1562/0006/1 Inspection Due: 13/07/2013
As at 06 November 2012 22Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
B, D 40Normal StrengthSectionsTRINECKE ZELEZARNY, a.s. PragueA 50DH32, DH36 40Higher StrengthAH27S, AH32, AH36 50
Univerzalni tratBezrucova 300
Tel: +42 (0) 596 082 097 or 558 533 897 Fax: +420 558 533 896 Email mailto:[email protected] Web http://www.trz.czThe approved sections are in the form of universal flats nominal widths 150 to 550mm to the maximum thicknesses shown above.Mechanical testing is carried out by approved works TRINECKE ZELEZARNY A.S. Certificate ID No: MD00/1562.Approval covers for heat treatment is carried out by approved works VITKOVICE HEAVY MACHINERY a.s. Parent Company: TRINECKE ZELEZARNY a.s., Prumyslova 1000, CZ-739 70 Trinec-Stare Metso.Certificate ID No : MD00/2020.Certificate No. MD00/3056/0004/1 Expiry date: 14/02/2013
735 93 Bohumín
As belowE.A.F. / IngotSteelmakingVITKOVICE HEAVY MACHINERY a.s. Praguecarbon, carbon-manganese, alloy 80IngotsSemi-Finished
Ruska 2887/10170602 Ostrava-VitkoviceTel: +420 595 95 6878 Fax: +420 595 95 6035 Email:[email protected] Web: http://www.vitkovice.czCertificate #: MD00/2020/0005/1 Expiry date: 01/04/2014
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingZDAS, a.s. Praguecarbon, carbon-manganese, alloy 12IngotsSemi-Finished
59171 Zdár nad SázavouMetallurgical Plant
Tel: +420 566 643 998 Fax: +420 566 642 803 Email: mailto:[email protected] Web:http://www.zdas.czCertificate #: MD00/1697/0004/1 Expiry date: 26/08/2014
carbon, carbon-manganese 4E.A.F. / IngotSteelmakingŽELEZÁRNY VESELÍ A.S. Prague
Rokycanská 204,338 42 Hrádek u Rokycan,
Division Železárny Hrádek,
Tel: +420 474 644096 Fax: +420 474 642 288 Email mailto:[email protected] Web: www.steel-holding.czCertificate #: MD00/4063/0001/1 Expiry date: 05/08/2015
Denmark
E 60Normal StrengthPlatesNLMK DANSTEEL A/S CopenhagenA, B, D 100EH32, EH36, EH36S 80Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36 100360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
DK-3300 FrederiksværkHavnevej 33
Tel: +45 477 82647 Fax: +45 477 70322 Email: mailto:[email protected] Web:http://www.dansteel.dkAll grades and thicknesses accepted with specified through thickness properties, Z25 and Z35 designations.Certificate Number: MD00/0403/0007/1 Expiry: 09/01/2015
Egypt, Arab Republic of
A, B, D 100Normal StrengthPlatesABU ZAABAL ENGINEERING INDUSTRIES Cairo
Inchas
Hot and Cold Rolling mill (AZE)Abu Zaabal
Tel: +20 224883220 Fax: +20 4883164 Email: [email protected]
Certificate # MD00/3421/0002/1 Expiry date: 27/01/2014
As belowB.O.S. / Con CastSteelmakingEGYPTIAN IRON & STEEL CO. Port SaidA 50Normal StrengthPlatesA 50Normal StrengthHot Rolled Coil360FG, 410FG 25Boiler & Pressure VesselA 50Normal StrengthSections
HelwanCairo
El Tebbin
Tel: +202 5940593 Fax +202 5011608 Email: mailto:[email protected] Web www.iron.steel.com.egTelex 20176 TebbinCertificate #: MD00/0438/0007/1 Expiry date: 23/02/2013
As at 06 November 2012 23Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Finland
As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS OY Helsinki/Helsingfors
austenitic stainless 187SlabsSemi-Finished
304L, 316L, 321 12Austenitic StainlessPlates
304L, 316L, 321 12Austenitic StainlessHot Rolled Coil
304L, 316L, 321 6Austenitic StainlessCoil
Terastie 1,95490
Tel No: +358 40 7675371 Fax no:+358 16 452 350Email:[email protected] Web: http://www.outokumpu.comCertificate #: MD00/1165/0006/1 Expiry date: 03/03/2014
Tornio
As belowE.A.F. / Con CastSteelmakingOVAKO IMATRA OY AB Turku/Åbocarbon, carbon-manganese, alloy 370BloomsSemi-FinishedAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
180Higher StrengthBars
carbon, carbon-manganese, alloy 180Structuralalloy 180Machinerycarbon, carbon-manganese 200
Terästehtaantie 1FI-55100 IMATRATel: +358 5 680 21 Fax: +358 5 680 2211 Email: mailto:[email protected] Web:http://www.ovako.comSemi-finished products in carbon, carbon-manganese and alloy steel with fine grain (element combinations as stated), blooms to 370 mm section, to 6000mm longfor further processing to rolled productsMQS Approved - Approval No. MQS 020Certificate #: MD00/0751/0009/1 Expiry date: 06/01/2015
As belowB.O.S. / Con CastSteelmakingRUUKKI METALS OY Turku/ÅboA, B, D, E 150Normal StrengthPlatesFH27S, FH32, FH36 40Higher StrengthAH40, DH40, DH42, EH40, EH42 80AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
150
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,510FG
100
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
40Ferritic Low Temperature
A, B, D, E 15Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
15Higher Strength
Rautaruukintie 155, PO Box 9392101 Raahe
Raahe Steel Works
Tel +358 20 5911 Mob +358 40 54 90257 Fax +358 20 5923527 Email:mailto:[email protected] Web: http://www.ruukki.com Specified through thickness properties for up to 100 mm thickness.
MQS Approved - Approval No. MQS 007Certificate #: MD00/1233/0008/1 Expiry date: 11/12/2013
As at 06 November 2012 24Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
France
Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingAKERS FRANCE Lyoncarbon, carbon-manganese, alloy 70IngotsSemi-Finished
B.P. 1020057104 Thionville Cedex
USINE DE THIONVILLEChemin du Leidt
Tel: +33 6 79 27 94 41 e mail: mailto:[email protected] web: http://www.akersrolls.comCertificate #: MD00/3386/0002/1 Expiry date: 27/05/2014
304L, 316L, 321, 304* 6Austenitic StainlessPlatesAPERAM Lyon
4 place des Forges71130 Gueugnon
Gueugnon Plant BP 1
Tel: +33 3 85 85 78 56 Fax: +33 3 85 85 14 12 Email: mailto:[email protected] Web: http://www.aperam.comCertificate #: MD00/1582/0005/1 Expiry Date: 11/03/2014
austenitic stainlessE.A.F. / IngotSteelmakingAPERAM ALLOYS IMPHY LyonFe-36Ni* 8Fe-Ni alloysPlatesFe-36Ni* 8Fe-Ni alloysHot Rolled Coil
Avenue Jean Jaurès58160 IMPHY*Cold and hot rolled strip up to 8mm in INVAR/M93 grade (Fe-Ni36) for approved applications.Tel: +33 3 86 21 31 23 Fax: +33 3 86 21 31 07 Email:mailto:[email protected] Web:http://www.imphyalloys.com
Certificate #: MD00/1870/0005/1 Expiry date: 14/06/2012
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL MarseilleA, B, D 16Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH36 13Higher Strength460FG, 490FG, 510FG 13Boiler & Pressure Vessel360AR, 410AR 16
13776 Fos-Sur-MerCEDEX
Méditerranée Fos-sur-Mer
Tel: +33 (0) 4 4247 3314 FAx +33 (0) 4 4247 1720 Emailmailto: [email protected] #: MD00/3803/00014/1 Expiry date: 25/11/2012
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELORMITTAL ATLANTIQUE LORRAINE Dunkerquecarbon, carbon-manganese 247SlabsSemi-Finished
BP 250859381 Dunkerque Cedex 1
ARCELOR MITTALSite de Dunkerque
Tel: +33 328 293220 Fax: +33 328 296974 Email mailto:[email protected] #: MD00/2232/0005/1 Expiry date: 09/06/2013
As belowE.A.F./Ingot/Con CastSteelmakingASCOMETAL Dunkerquecarbon, carbon-manganese, alloy 400Blooms/BilletsSemi-Finishedcarbon, carbon-manganese, alloy 310StructuralBarscarbon, carbon-manganese, alloy 310MachineryU3 105Chain Cable StockU1, U2 130
59941 DunkerqueCedex 2
Usine de DunesBP 41
Machinery grades up to 180 mm by continuous casting, 310 mm by ingotTel +33 32829 6203 Fax +33 32829 6003Certificate #: MD00/0117/0006/1 Expiry date: 13/09/2012
As belowE.A.F. / IngotSteelmakingASCOMETAL Marseillecarbon, carbon-manganese, alloy 400BloomsSemi-Finishedcarbon, carbon-manganese, alloy 205Billetscarbon, carbon-manganese, alloy 325StructuralBars
13771 Fos-sur-Mer
Usine de Fos-sur-MerBP 30
Tel: +33 (0) 442 479 216 Fax: +33 (0) 442 051 511 Email : mailto:[email protected] Number: MD00/0118/0006/1 Expiry: 03/09/2015
As belowE.A.F. / IngotSteelmakingAUBERT & DUVAL Lyoncarbon, carbon-manganese, alloy, austeniticstainless steel
450Blooms/BilletsSemi-Finished
carbon, carbon-manganese, alloy, austeniticstainless
50StructuralBars
carbon, carbon-manganese, alloy, austeniticstainless
200Machinery
As at 06 November 2012 25Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
BP 163770 Les Ancizes
Aciéries des Ancizes
Tel: +33 4 7367 3128 Fax: +33 4 7367 3174 Email: mailto:[email protected]: http://www.aubertduval.comCertificate #: MD00/0127/0005/1 Expiry date: 05/03/2013
As belowB.O.S. / Con CastSteelmakingCELSA FRANCE BilbaoNormal Strength, Higher Strength 160BilletsSemi-Finished
Rond-Point Claudius Magnin64340 BoucauTel: +33 05 59 64 41 00 Fax: +33 05 59 64 41 21 email: [email protected] Web: http://www.celsafrance.comBillets as semi-finished products, nominal 160mm width and nominal 13300mm length to the above maximum thickness are approved for further processing forrolled products.Certificate Number: MD00/3539/0002/1 Expiry date: 12/11/2014
E 80Normal StrengthPlatesGTS Industries DunkerqueA, B, D 100AH40, DH40, EH40, FH40 42Higher StrengthFH27S, FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
75
460FG, 490FG, 510FG 50Boiler & Pressure Vessel360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
BP 631759379 Dunkerque Cedex 1
Dunkerque Mill
Tel: +33 (0)3 28 29 39 64 Fax: +33 (0)3 28 29 69 12 Email:mailto:[email protected]: http://www.gts-dillinger.frSpecified through thickness properties for all nornal and higher strength grade plates notation Z35 may be added.Certificate #: MD00/1818/0007/1 Expiry date: 09/06/2013
carbon, carbon-manganeseE.A.F. / IngotSteelmakingINDUSTEEL FRANCE LyonA 400Normal StrengthPlatesFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 400360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni
50Ferritic Low Temperature
BP 368 - Chateauneuf42803 RIVE DE GIER
ARCELOR MITTALSite de Chateauneuf
Tel: +33 4 77 75 21 12 Fax: +33 4 77 75 20 03 Email: mailto:[email protected]
Including plates with specified through thickness properties.Certificate #: MD00/0351/0006/1 Expiry date: 20/04/2014
As belowE.A.F. / IngotSteelmakingINDUSTEEL FRANCE, site du Creusot Lyoncarbon, carbon-manganese, alloy, austeniticstainless
40IngotsSemi-Finished
71201 71201 LE CRUUSOT CEDEXLe Creusot Cedex
Porte du Breuil - BP 34
Tel No 33 3 8580 5575 Fax No. 33 3 8580 5211Email: [email protected]: www.industeel.infoCertificate number MD00/3227/0001/1Ingots also in martensitic stainless steel up to 40 T for approved applications
A, B, D, E 150Normal StrengthPlatesINDUSTEEL FRANCE, site du Creusot LyonFH32, FH36 50Higher StrengthAH32, AH36, DH32, DH36, EH32, EH36 150360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 1.5Ni, 3.5Ni, 5Ni,9Ni
50Ferritic Low Temperature
304L, 316L 50Austenitic Stainless
7120156 rue Clemenceau - BP19
Tel: +33 3 8580 5575 Fax: +33 3 8580 5211Email: mailto:[email protected] Web: http://www.industeel.infoPlates with specified through thickness properties.Certificate #: MD00/1822/0007/1 Expiry date: 27/02/2015
As at 06 November 2012 26Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingLAMINES MARCHANDS EUROPEENS Lyoncarbon, carbon-manganese 200BilletsSemi-FinishedA 13Normal StrengthSectionsA 30Normal StrengthBars
2, Rue Emile Zola59125 Trith St LégerTel +33 (0)3 2714 2270 Fax +33 (0)3 2714 2010 Email: mailto:[email protected] #: MD00/1395/0007/1 Expiry date: 20/10/2013
As belowE.A.F./A.O.D./Con CastSteelmakingUGITECH S.A. LyonAs below 205BilletsSemi-Finished304L, 316L, 321 32Austenitic StainlessSectionsUNS S31803 32Duplex Stainless304L, 316L, 321 130Austenitic StainlessBarsUNS S31803 130Duplex Stainlessaustenitic stainless, duplex stainless, martensiticstainless*
95Machinery
Avenue Paul Girod,73403 UGINE CedexTel: +33 4 79 89 32 92 Fax: +33 4 79 89 34 74 Email: mailto:[email protected] Web: http://www.ugitech.comCertificate #: MD00/1583/0006/1 Expiry Date: 24/08/2014
Germany
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL BREMEN GmbH BremenAs below 220SlabsSemi-FinishedA, B, D 20Normal StrengthHot Rolled Coil360, 410, 360FG, 410FG 20Boiler & Pressure Vessel
Carl-Benz- Straße 30D-28237 BremenTel +49 421 648 2306 Fax +49 412 648 3150 Email: mailto:[email protected] Web: http://www.arcelormittal.com/bremenCertificate No. MD00/0857/0005/1 Expiry date: 19/10/2013
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELORMITTAL EISENHÜTTENSTADT GMBH Dortmundcarbon, carbon-manganese 225SlabsSemi-Finishedcarbon, carbon-manganese 300Blooms
D-15872 EisenhüttenstadtWerkstraße 1
Tel +49 3364 3782 05 Fax +49 3364 3781 97 Email: mailto:[email protected] Web http://www.arcelormittal-ehst.comContinuously cast slab up to 250 mm thickness and cast bloom up to 300 mm thickness.Certificate No. MD00/0450/0005/1 Expiry date: 22/01/2013
As belowB.O.S. / Con CastSteelmakingARCELORMITTALAL RUHRORT GmbH Dortmundcarbon, carbon-manganese, alloy 385BloomsSemi-Finishedcarbon, carbon-manganese, alloy 130Billets
Vohwinkelstraße 107D-47137 DuisburgTel 0049 (0) 203 / 52 66 180 Fax 0049 (0) 203 / 606 66 332 email: [email protected] Web http://www.arcelormittal.comCertificate Number: MD00/3631/0002/1 Expiry date: 25/07/2014
As belowB.O.S./Ingot/Con CastSteelmakingAktiengesellschaft der Dillinger Hüttenwerke HamburgA, B, D, E 170Normal StrengthPlatesFH32, FH36 50Higher StrengthAH40, DH40, EH40 100AH32, AH36, DH32, EH32 170DH36, EH36 220360FG, 410FG, 460FG, 490FG, 510FG 100Boiler & Pressure VesselLTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36, 5Ni
50Ferritic Low Temperature
HüttenwerkstrassePostfach 1580
Tel: +49 6381 474735 Fax: +49 6831 473689 Email: mailto:[email protected] Web:http://www.dillinger.deAll plates with specified through thickness properties.Certificate No. MD00/0361/00012/1 Expiry date: 20/09/2014
D-66748 Dillingen / Saar
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingBENTELER STEEL/TUBE GmbH Dortmundcarbon, carbon-manganese, alloy 215SlabsSemi-Finishedcarbon, carbon-manganese, alloy 310Blooms/Billets
As at 06 November 2012 27Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR OfficeNiederdarmer Straße 5D-49811 LingenTel: +49 591 80004 800 Fax: +49 591 80004 460 Email to: [email protected] Web: http://www.benteler.deCertificate No. MD00/1805/0006/1 Expiry date: 11/10/2014
Steelmaking and semi-finished slabs, blooms and billets intended for plates, forgings and tubes.Semi-finished products in carbon, carbon-manganese and alloy steel: slabs to 670mm wide, to 11,500mm long to 12.8 tonnes and blooms/billets of dimensions300mm x 230mm or 310mm round of maximum length 12,800mm
As belowE.A.F./Ingot/Con CastSteelmakingBGH EDELSTAHL FREITAL GmbH Dortmundalloy, austenitic stainless, duplex stainless,stainless steels
12IngotsSemi-Finished
stainless steel 230SlabsAs below 120Billetsalloy, austenitic stainless, duplex stainless,martensitic stainless*
165MachineryBars
Am Stahlwerk 1D-01705 FreitalTel: +49 (0)351 646 2232 Fax: +49 (0)351 646 2888 Email: mailto:[email protected] Web: http://www.bgh.deIncluding forged barsCertificate No. MD00/1973/0006/1 Expiry date: 06/08/2014
alloy, austenitic stainless 32IngotsSemi-FinishedBGH EDELSTAHL SIEGEN GmbH DortmundIndustriestraße 9,D-57076
Tel No. +49 (0)271 701- 341 Fax No. +49 (0) 271 701- 300Email [email protected] www.bgh.deCertificate No MD00/3767/0001/1 Expiry date: 01/04/2013
Siegen
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingBUDERUS EDELSTAHL GmbH Dortmund
carbon, carbon-manganese, alloy 200Semi-finished ProductsBarscarbon, carbon-manganese, alloy 190Machinery
Buderusstraße 25D-35573 WetzlarTel: +49 (0)6441 374 2505 Fax: +49 (0)6441 374 2681 Email: mailto:[email protected] Web: http://www.buderus-steel.comCertificate No. MD00/0257/0008/1 Expiry date: 08/07/2014
As belowE.A.F. / Con CastSteelmakingDEUTSCHE EDELSTAHLWERKE GMBH DortmundAs belowE.A.F. / Ingotcarbon, carbon-manganese, alloy, austeniticstainless
80StructuralBars
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, martensitic stainless*
80Machinery
Obere KaiserstraßeD-57078 Siegen
Works Siegen
Tel: +49 (0)271 808 26 94 Fax: +49 (0)271 808 25 01 Email: mailto:[email protected] Web: http://www.dew-stahl.comCertificate No. MD00/0901/0008/1 Expiry date: 12/07/2014
As belowE.A.F. / Con CastSteelmakingDEUTSCHE EDELSTAHLWERKE GMBH DortmundAs belowE.A.F. / Ingotcarbon, carbon-manganese, alloy, austeniticstainless
250Semi-finished ProductsBars
alloy, austenitic stainless 250Structuralalloy, austenitic stainless, duplex stainless,martensitic stainless*
250Machinery
Auestraße 4D-58452 Witten
Works Witten
Tel: +49 (0) 2302 294 131 Fax: +49 (0) 2302 294 662 Email:mailto:[email protected] Web:http://www.dew-stahl.comCertificate No. MD00/2075/0010/1 Expiry date: 21/01/2013
As belowE.A.F. / IngotSteelmakingELEKTROSTAHLWERKE GRÖDITZ GmbH Dortmundcarbon, carbon-manganese, alloy, austeniticstainless
84IngotsSemi-Finished
D-01609 GröditzRiesaer Straße 1
Tel: +49 35263 62-611 Fax: +49 35263 62-622 Email: mailto:[email protected] Web:http://www.stahl-groeditz.deCertificate No. MD00/2880/0005/1 Expiry date: 12/04/2014
As belowE.A.F./Ingot/Con CastSteelmakingGEORGSMARIENHÜTTE GmbH Dortmundcarbon, carbon-manganese, alloy 44IngotsSemi-Finishedcarbon, carbon-manganese, alloy 240BloomsA, B, D, E 180Normal StrengthBarsAH32, AH36, DH32, DH36, EH32 180Higher Strengthalloy 270Structuralcarbon, carbon-manganese 280
As at 06 November 2012 28Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
GermanyU1, U2, U3, R3 155Chain Cable StockBarsGEORGSMARIENHÜTTE GmbH Dortmund
D-49124 GeorgsmarienhütteNeue Hüttenstraße 1
Tel: +49 (0)5401 39-0 Fax: +49 (0)5401 394598 Email: [email protected] Web: http://www.gmh.deCertificate No. MD00/0596/0006/1 Expiry date: 04/10/2013
As belowE.A.F. / Con CastSteelmakingH.E.S. HENNIGSDORFER ELEKTROSTAHLWERKEGmbH
Dortmund
carbon, carbon-manganese, alloy 100StructuralBars
carbon, carbon-manganese, alloy 50Machinery
U1, U2 73Chain Cable Stock
Wolfgang-Küntscher-Straße 18D-16761 HennigsdorfTel: +49 (0)3302 806-0 Fax: +49 (0)3302 806-211 Email: mailto:[email protected] Web: http://www.rivagroup.comCertificate No. MD00/0665/0007/1 Expiry date: 01/07/2014
A 50Normal StrengthSectionsHOESCH SCHWERTER PROFILE GmbH DortmundEisenindustriestraße 1D-58239 SchwerteTel: +49 (0)2304 106-340 Fax: +49 (0)2304 106-590 Email: mailto:[email protected] Web: http://www.hoesch-profile.deCertificate No. MD00/0682/0006/1 Expiry date: 08/01/2015
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingHüttenwerke Krupp Mannesmann GmbH Dortmundcarbon, carbon-manganese, alloy 260SlabsSemi-Finishedcarbon, carbon-manganese, alloy 406Blooms/Billets
Ehinger Strasse 200D-47259 Duisburg-Huckingen
Huckingen Works
Tel: +49 (0)203 999-01 Fax: +49 (0)203 999-4411 Email: mailto:[email protected] Web: http://www.hkm.deCertificate No. MD00/0730/0006/1 Expiry date: 07/02/2015
B, D, E 85Normal StrengthPlatesILSENBURGER GROBBLECH GmbH DortmundA 150AH40, DH40, EH40, FH40 100Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
120
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 360FG, 410FG, 460FG, 490FG,510FG
100
LTAH40, LTDH40, LTEH40, 1.5Ni, 3.5Ni, 5Ni,9Ni
50Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
120
316L 80Austenitic StainlessVeckenstedter WegD-38871 IlsenburgAll plates with specified through thickness properties.
Tel: +49 39452/85 5530 Fax: +49 39452/85 5733 EMail mailto:[email protected] Web: http://www.ilsenburger-Grobblech.deCertificate No. MD00/1654/0012/1 Expiry date: 24/02/2014
As belowE.A.F. / Con CastSteelmakingLech-Stahlwerke GmbH HamburgA, B 100Normal StrengthBarscarbon, carbon-manganese, alloy 90Machinery
Industriestrasse 1D-86405 Meitingen
Meitingen-Herbertshofen
Tel: +49 (0) 8271/82-325 Fax: +49 (0) 8271/82-405 Email:mailto:[email protected] Web: http://www.lech-stahlwerke.deCertificate No. MD00/0921/0005/1 Expiry date: 03/11/2012
As belowE.A.F. / Con CastSteelmakingPEINER TRÄGER GMBH DortmundA, B, D, E 40Normal StrengthSectionsAH32, AH36, DH32, DH36, EH32, EH36 40Higher Strength
D-31226 PeineGerhard-Lucas-Meyer Str. 10
Tel: +49 5171 91 9321 Fax: +49 5171 91 9373 Email: [email protected] Website: www.peinertraeger.deCertificate No. MD00/3075/0003/1 Expiry date: 14/05/2013
As at 06 November 2012 29Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 250Normal StrengthPlatesREINER BRACH GmbH & Co. KG BremenAH32, AH36, DH32, DH36, EH32, EH36 120Higher StrengthAH27S, DH27S, EH27S 250460FG, 490FG, 510FG 120Boiler & Pressure Vessel360FG, 410FG 150
Wilhelm-Karmann-Straße 5D-28237 BremenTel: +49 421 985 08-140 Fax: +49 421 985 08-149 Email mailto:[email protected] Web:http://www.brach.deCertificate No. MD00/2631/0006/1 Expiry date: 01/01/2015
carbon, carbon-manganese 43IngotsSemi-FinishedREINER BRACH GmbH & Co. KG Bremen
Werkstraße,16D-15890 Eisenhüttenstadt
Betriebsstätte Eisenhüttenstadt
Tel No +49 3364 37 81 54 Fax No +49 3364 37 81 55Email: [email protected]: www.brach.deCertificate No. MD00/4032/0001/1 Expiry Date 08/06/2015
Carbon, Carbon-manganese 56EAF/LRF/VD/IngotSteelmakingSAARSCHMIEDE GmbH FREIFORMSCHMIEDE HamburgBismarckstraße 57-59D-66330 VölklingenTel:+49 (0)6898 102650 Fax:+49(0)6898 104560 Email:mailto: [email protected] Web:http://www.saarschmiede.comCertificate No. MD00/2017/0001/1 Expiry date: 25/06/2014
A 40Normal StrengthBarsSAARSTAHL AG HamburgU1, U2, U3 40Chain Cable Stock
D-66511 NeunkirchenWorks Neunkirchen
Tel: +49 6821 168644 Fax: +49 6898 1054293 Email: mailto:[email protected] Web:http://www.saarstahl.comCertificate No. MD00/1286/0006/1 Expiry date: 10/08/2014
As belowB.O.S. / Con CastSteelmakingSAARSTAHL AG HamburgNormal Strength 265Blooms/BilletsSemi-FinishedA 160Normal StrengthBarsU1, U2, U3 100Chain Cable Stock
Bismarckstrasse 57 - 59D-66330 Völklingen
Works Völklingen
Tel: +49 (0) 6898 104 293 Fax: +49 (0) 6898 105 4293 Email: mailto:[email protected] Web:http://www.saarstahl.comCertificate Number: MD00/1931/0006/1 Expiry: 10/08/2014
As belowB.O.S. / Con CastSteelmakingSALZGITTER FLACHSTAHL GmbH Dortmundcarbon, carbon-manganese 350SlabsSemi-Finished
D-38239 Salzgitter,Eisenhüttenstrasse 99,Tel: +49 5341 21-3196 Fax: +49 5341 21-2008Email: [email protected]: www.salzgitter-flachstahl.de
Approved slab section sizes up to 350 x 2600mm.
Steel types carbon and carbon-manganese cover the supply of slabs for processing into normal strength, high strength, boiler and pressure vessel grades andferritic steels for low temperature service according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The finalprocessing mill is responsible for ordering steel which complies with their approved chemical composition and enables them to achieve the required mechanicalproperties.
A, B, D, E 50Normal StrengthPlatesSALZGITTER MANNESMANN GROBBLECH GmbH DortmundAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50304L, 316L 50Austenitic Stainless
Wiesenstraße 36D-45473 Mülheim an der RuhrTel: +49 (0)208 458 458 4510 Fax: +49 (0)208 458 1872 Email: mailto:[email protected] Web: http://www.smgb.deCertificate No. MD00/1806/0006/1 Expiry date: 28/04/2014
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingSTAHLWERK BOUS GMBH Hamburgcarbon, carbon-manganese 60IngotsSemi-Finished
D-66359 Bous/SaarP/O Box 1243
Tel: +49 6834 81286 Fax: +49 6834 81586 Email: mailto:[email protected] Web http://www.stahlwerk-bous.deIngots up to 60 tonne and 2300 mm dia.Certificate #: MD00/1249/0005/1 Expiry date: 21/08/2013
As at 06 November 2012 30Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingSTAHLWERK THÜRINGEN GMBH DortmundA, B 25Normal StrengthSectionsAH32, AH36, DH32, DH36 25Higher Strength
D-07333 UnterwellenbornKronacher Straße 6
Tel +49 3671 455006010 Fax +49 3671 45507710 Email: mailto:[email protected] Web http://www.stahlwerk-thueringen.deCertificate #: MD00/1424/0006/1 Expiry date: 22/11/2012
As belowE.A.F. / IngotSteelmakingSchmidt + Clemens GmbH + Co. KG Dortmundcarbon, carbon-manganese, alloy, austeniticstainless
50StructuralBars
D-51789 LindlarKaiserau 2
Tel: +49 (0)22 62232 Fax: +49 (0)22 668232 Email: mailto:[email protected] Web http://www.schmidt-clemens.deCertificate #: MD00/1319/0006/1 Expiry date: 12/10/2010
A, B, D, E 20Normal StrengthHot Rolled CoilTHYSSENKRUPP STEEL EUROPE AG DortmundAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure VesselA, B, D, E 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength410 FG, 460 FG, 360 FG, 360, 410, 490FG, 510FG 20Boiler and Pressure Vessel
Kaiser-Wilhelm-Straße 100D-47166 Duisburg
Works Bochum
Tel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:[email protected] Web: http://www.thyssenkrupp-stahl.comCertificate No. MD00/0899/0007/1 Expiry date: 24/08/2014
As belowB.O.S. / Con CastSteelmakingTHYSSENKRUPP STEEL EUROPE AG DortmundAs below 255SlabsSemi-FinishedA, B, D, E 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel
Works BeeckerwerthTel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:[email protected] Web: http://www.thyssenkrupp-stahl.comCertificate # MD00/1823/0007/1 Expiry date: 19/08/2014
As belowB.O.S. / Con CastSteelmakingTHYSSENKRUPP STEEL EUROPE AG DortmundA, B, D, E 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 20Boiler & Pressure Vessel
Works BruckhausenTel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:[email protected] Web: http://www.thyssenkrupp-stahl.comCertificate No. MD00/1824/0007/1 Expiry date: 25/08/2014
A, B, D, E 150Normal StrengthPlatesTHYSSENKRUPP STEEL EUROPE AG DortmundFH27S, FH32, FH36 50Higher StrengthAH40, DH40, EH40 60AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
UNS S31803 35Duplex StainlessA, B, D, E 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36,EH27S, EH32, EH36
20Higher Strength
360 FG, 460 FG, 410 FG, 360, 410, 490FG, 510FG 20Boiler and Pressure VesselWorks Duisburg-SüdTel: +49 (0)203 52-1 Fax: +49 (0)203 52-43587 Email: mailto:[email protected] Web: http://www.thyssenkrupp-stahl.comSpecified through thickness properties on all normal and higher strength steel grade plates.Certificate No. MD00/1825/0008/1 Expiry date: 19/08/2014
As belowE.A.F./Ingot/Con CastSteelmakingThyssenKrupp Nirosta GmbH Dortmundaustenitic stainless 16IngotsSemi-Finishedaustenitic stainless 240Slabs
Oberschlesienstraße 16D-47807 Krefeld
Works Krefeld
Tel: +49 (0) 211 7107 562 Fax: +49 (0) 211 7107 376 Email: mailto:[email protected] Web: http://www.thyssenkrupp.comIngots as semi finished products nominal dimensions 1700 x 690xmm & nominal height 2600mm to the above maximum weight and slabs as semi finishedproducts nominal width 1500mm & nominal length 10000mm, are approved for further processing for rolled products.Certificate Number: MD00/1852/0006/1 Expiry date: 16/11/2014
As at 06 November 2012 31Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Hungary
B, D, E 35Normal StrengthPlatesISD DUNAFERR Zrt. Lörinci Meleghengermü ViennaA 100AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
60Higher Strength
360, 410 35Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 60
Hengersor u. 381184 BudapestTel: +36 1 296 2200/6206 Fax: +36 1 296 2201 Email: mailto:[email protected] Web http:\\www.dunaferr.huCertificate No. MD00/0425/0007/1 Expiry date: 05/03/2012
India
Carbon, Carbon-manganese, AlloyEAF/LRF/VD/IngotSteelmakingARCVAC FORGECAST LTD Calcuttacarbon, carbon-manganese, alloy 10IngotsSemi-Finished
Post Box: 9210Kolkata: 700071
12C, Lord Sinha Road,
Tel: + 91 33 2600 2176; Fax + 91 33 2659 8002Email: [email protected]: www. arcvacsteel.comCertificate No. MD00/3561/0003/1 Expiry date: 07/02/2015
West Bengal
As belowE.A.F. / Con CastSteelmakingESSAR STEEL INDIA LTD. MumbaiNormal strength, Higher Strength 260SlabsSemi-FinishedA, B 20Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher Strength360FG, 410FG 20Boiler & Pressure VesselA, B 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 20Higher Strength
Hazira - 394270District Surat
Hot Strip Mill
Tel: +91 261 6683139 Fax: +91 261 6683747 Email mailto:[email protected] Web http://www.essar.com Slabs as semi finished products nominal maximum width 2040mm x nominal maximum length 4900mm to the above maximum thickness are approved forfurther processing for rolled products.Certificate No. MD00/2091/0008/1 Expiry date: 06/06/2015
Gujarat
A, B, D 70Normal StrengthPlatesESSAR STEEL INDIA LTD. MumbaiAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength
Plate Mill DivisionTel: +91 261 668 3291 or 6739 Fax: +91 261 668 3747 Email mailto:[email protected] or [email protected] Webhttp://www.essar.com All plates are restricted to a maximum width of 4550mm.Certificate Number: MD00/3979/002/1 Expiry: 17/01/2015
As belowE.A.F./A.O.D./Con CastSteelmakingFACOR STEELS LTD New Delhiaustenitic stainless, duplex stainlessB.O.S/V.O.D./Con Cast11CrMo91 45Boiler & Pressure VesselsBars13CrMo45 50410AR, 460AR, 490 63304L, 316L 100Austenitic StainlessUNS S31803 122Duplex StainlessU3 56Chain Cable StockU1, U2 80
MIDC Hingna Industrial Estate,Nagpur
Tel No . +91 7104 235701-5 Fax No. +91 7104 235709Email info@{facorsteels.comWeb site: www.facorsteel.comCertificate No MD00/3786/0001/1 Expiry date 18/05/2013
440028
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingISMT LIMITED (STEEL PLANT) Punecarbon, carbon-manganese, alloy 225BloomsSemi-Finishedcarbon, carbon-manganese, alloy 150Bars
As at 06 November 2012 32Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Jejuri 412 303Purandara, Pune
Morgaon Road
Tel: +91-020-26630144 / +91-020-26630714 Fax: +91-020-26630779 Email mailto: [email protected] Web http://www.ismt.co.inCertificate number. MD00/3816/0001/1 Expiry date: 24/08/2013
Maharashtra
As BelowB.O.S./E.A.F./Con CastSteelmakingJINDAL STEEL & POWER LIMITED New DelhiA, B, D 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 80Higher Strength360AR, 410AR, 460AR, 360, 410, 460, 490, 360FG,410FG, 460FG, 490FG
80Boiler & Pressure Vessel
Post Box No.16Kharsia Road
Raigarh
Tel: +91 7762 227001 10 Fax: +91 7762 227021/22 Email to [email protected] Certificate No. MD00/3542/0002/1 Expiry date: 02/08/2014
Raigarh 496001 Chattisgarh
austenitic stainlessE.A.F./A.O.D./Con CastSteelmakingJSL STAINLESS LTD. Yamunanagaraustenitic stainlessB.O.S/V.O.D./Con CastAs below 160SlabsSemi-Finished304L, 316L, 317L, 321, 347 53Austenitic StainlessPlates
O.P. Jindal MargHisar Haryana State
Post Box No. 6
Tel: +91 1662 222471 - 83 ext 2336 Email: mailto:[email protected] Web Page www.jindalstainless.comCertificate No. MD00/3110/0003/1 Expiry date: 22/10/2013
India Pin 125 005
A, B, D, E, AH32, AH36, DH32, DH36, EH32,EH36
220B.O.S. / Con CastSteelmakingJSW STEEL LIMITED Mumbai
583 275 ToranagalluDist Bellary
Vidyanagar WorksP.O. Vidyanagar
Tel: +91 8395 250 120 Fax: +91 8395 250 114 Email: [email protected] Web: www.jsw.inCertificate No. MD00/3564/0001/1 Expiry date: 10/02/2012
Karnataka
As belowE.A.F./Ingot/Con CastSteelmakingKALYANI CARPENTER SPECIAL STEELS LTD. Punecarbon, carbon-manganese, alloy 250Semi-finished ProductsBarscarbon, carbon-manganese, alloy 150Structural
MundhwaPune 411 036Tel: +91 20 9881132054 Fax: +91 20 26824483 Email: mailto:[email protected] Web: http://www.kalyanicarpenter.comCertificate No. MD00/0815/0007/1 Expiry date: 23/08/2012
As belowE.A.F. / IngotSteelmakingNAVYUG SPECIAL STEEL PVT. LTD. Mumbaialloy, austenitic stainless steelBlooms/BilletsSemi-Finishedcarbon, carbon-manganese 340A 50Normal StrengthSectionsA 200Normal StrengthBars
KhopoliDist. Raigad
Khopoli WorksJagdish Nagar
Tel: +91 952192 263318 (263347) Fax: +91 952192 263582 (263076) Email mailto:[email protected] www.mahindra.comCertificate No. MD00/0971/0007/1 Expiry date: 17/07/2012
Maharashtra 410 216
As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. BhilaiA, B, D 75Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
460FG, 490FG, 510FG 50Boiler & Pressure Vessel360AR, 410AR, 360, 410 63360FG, 410FG 75
Bhilai 490 001Chhattisgarh
Bhilai Steel Plant
Tel +91 940 7981686 Fax +91 788 2222040 Email:mailto:[email protected] No. MD00/1433/0008/1 Expiry date: 28/04/2014
As belowB.O.S. / Con CastSteelmakingSTEEL AUTHORITY OF INDIA LTD. CalcuttaA, B 52Normal StrengthPlates360, 410, 360FG, 410FG 35Boiler & Pressure Vessel360AR, 410AR 40
As at 06 November 2012 33Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Rourkela 769 011Orissa
Rourkela Steel Plant
Tel +91 (0)661 2511210 Fax +91 (0)661 2510183 Email mailto:[email protected] No. MD00/1434/0005/1 Expiry date: 24/06/2013
As belowB.O.S. / Con CastSteelmakingTATA STEEL LIMITED CalcuttaA 50Normal StrengthPlates360AR, 410AR 50Boiler & Pressure VesselA 12Normal StrengthHot Rolled Coil
Kolkata 700 07143 Chowringhee Road
Tel: +91 (33) 22889251 Fax: +91 (33) 22887255/22881396 Email mailto:[email protected] Web http://www.tata.comCertificate No. MD00/1489/0006/1 Expiry date:15/02/2015
alloyE.A.F. / IngotSteelmakingU.P. STEELS New Delhi
Meerut Road,Muzaffarnagar - 251 203
A Unit of ISGEC Heavy Engineering LimitedNara
Tel +91 1396 252404/5/6 Fax + 91 1396 252324Email: [email protected]: www.upsteels.comCertificate No. MD00/1984/0003/1 Expiry date: 07/08/2014
Uttar Pradesh
austenitic stainless steelIF/AOD/Ingot/ConCastSteelmakingVIRAJ PROFILES LIMITED (SMS DIVISION) Mumbaiaustenitic stainless steel 300Blooms/BilletsSemi-Finished
Boisar, Taluka - Palghar, Dist. Thane,Maharashtra - 401506,
G-2 / G23 MIDC, Tarapur Industrial Area,
Tel: +91 2525 261514 Fax: +91 2525 260159 Email mailto:[email protected] Web: http://www.viraj.comBillets and blooms as semi-finished products to the above maximum thickness, nominal 300mm wide x nominal 9000mm long are approved for furtherprocessing for forged products.Certificate Number: MD00/2935/0004/1 Expiry date: 08/12/2014
A, B, D 50Normal StrengthPlatesWelspun Corp Limited MumbaiAH27S, AH32, DH27S, DH32 25Higher Strength460FG, 490FG 25Boiler & Pressure Vessel360FG, 410FG 35
Taluka.: Anjar, Dist.: Kutch,Gujarat - 370110
(Plate & Coil Mills Division)Survey No. 659, Village: Versamedi,
Tel: +91 2836 661728 - 4114 Fax: +91 2836 664141 Email: [email protected] Web: http://www.welspuncorp.comCertificate Number: MD00/3887/0001/1 Expiry date: 28/02/2014
Indonesia
B, D 25Normal StrengthPlatesPT. GUNAWAN DIANJAYA STEEL JakartaA 40AH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength360AR, 410AR 25Boiler & Pressure Vessel
Jl. Margomulyo No. 29AGreges-Asemrowo
Tel: +62 31 7490598 Fax: +62 31 7490581/7482109Email: mailto:[email protected] Web http://www.gunawansteel.comCertificate No. MD00/1882/0007/1 Expiry date: 16/12/2012
Surabaya 60183
A, B 50Normal StrengthPlatesPT. GUNUNG RAJA PAKSI JakartaAH36, AH40, DH36, DH40, EH36, EH40 50Higher Strength360AR, 410AR 40Boiler & Pressure VesselA, B 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 14Higher Strength360AR, 410AR 16Boiler & Pressure Vessel
JI. Imam Bonjol 4, Warung BongkokDesa Sukadanau, Clkarang Barat, Bekasi
Tel: +62 21 8900111 ext 3518 Fax: +62 21 8900333Email: mailto:[email protected] Web: http://www.grdsteel.comCertificate No. MD00/2749/0003/1 Expiry date: 15/11/2013
West Java, Indonesia
A, B 25Normal StrengthPlatesPT. JAYA PARI STEEL Tbk. SurabayaJl Margomulyo No. 4Tandes
Tel: +62 31 7491288 Fax:+62 31 7491714 Email:mailto:[email protected] No. MD00/2304/0006/1 Expiry date: 26/04/2014
Surabaya 80186
As at 06 November 2012 34Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingPT. KRAKATAU STEEL (PERSERO) JakartaA 25Normal StrengthPlates
Jl. Industri No. 5PO. Box 14
Divisi P & PM (QA)
Tel: +62 254 371047 Fax: +62 254 372725 Email: mailto:[email protected] Web: http://www.krakatausteel.comCertificate No. MD00/1183/0006/1 Expiry date: 02/02/2012
Cilegon 42435
Italy
As belowE.A.F./Ingot/Con CastSteelmakingA.B.S. Acciaierie Bertoli Safau S.p.A. TriesteCarbon, Carbon manganese, Alloy 370Rolled BarsSemi-FinishedCarbon, Carbon-manganese, Alloy 700As Cast Round SectionCarbon, Carbon-manganese, Alloy 420Rolled Square Barscarbon, carbon-manganese, alloy 170StructuralBarscarbon, carbon-manganese, alloy 170MachineryU1, U2, U3 78Chain Cable Stock
33050 Pozzuolo del Friuli (UD)Via Buttrio, 28
Tel: +39 (0) 432 613 211 Fax: +39 (0) 432 613 249 E-mail: mailto:[email protected] Web: http://www.absacciai.itCertificate No. MD00/0019/0008/1 Expiry date: 15/06/2014
carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingACCIAIERIA DI RUBIERA S.p.A. Ravennacarbon, carbon-manganese, alloy 100IngotsSemi-Finishedcarbon, carbon-manganese, alloy 180Billets
42013 S. Donnino di Casalgrande (R.E.)Via XXIV Aprile, 64
Tel: +39 0522 997209 Fax: +39 0522 840040 Email: mailto:[email protected] Web http://www.acciaieriadirubiera.comAddress for orders: Acciaieria di Rubiera S.p.A. , Via San Cataldo, 115, 41100 Modena, Italy.Certificate No. MD00/0038/0005/1 Expiry date: 08/03/2013
As below, carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingACCIAIERIA FONDERIA CIVIDALE S.P.A. Triestecarbon, carbon-manganese, alloy 35IngotsSemi-Finished
Zona Industriale no. 4033043 Cividale del Friuli
Via delle Industrie
Steel types carbon, carbon-manganese and alloy cover the supply of ingots for processing into forgings according to the Society's Rules for the Manufacture,Testing and Certification of Materials, Chapter 5. The final processing mill is responsible for ordering steel which complies with their approved chemicalcomposition and enables them to achieve the required mechanical propertiesTel +39 432 706922 Fax +39 432 706920 Email:mailto:[email protected] www.cividalespa.comCertificate No. MD00/3149/0002/1 Expiry date: 04/04/2011
(Udine)
As belowE.A.F./Ingot/Con CastSteelmakingACCIAIERIE VALBRUNA S.P.A. Venicecarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
10IngotsSemi-Finished
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless
220Billets
austenitic stainless, precipitation hardenedstainless*, martensitic stainless*
155MachineryBars
duplex stainless 205
36100 VicenzaViale Della Scienza, 25 z.i.
Tel: +39 0444 968211 Fax: +39 0444 968182 Email:mailto:[email protected] Web:http://www.acciaierie-valbruna.com* Accepted for approved applicationsApproval for Precipitation Hardened Stainless Machinery Bar is for Grade 17.4 PH, approval for Martensitic Stainless Machinery Bar is for Grade 431 and Grade1.4418 Quenched and Tempered.Duplex Stainless Steel bars are not approved for use in welded construction, and weld repair is not permitted.Approval of Con cast material is for the production of Austenitic Stainless Steels only.Ingots as semi finished products nominal maximum dimensions 600mm x 530mm x 2060mm to the above maximum weight are accepted for further processingfor rolled products and forgings.Billets as semi finished products nominal maximum width 220mm x nominal maximum length 6500mm to the above maximum thickness are accepted forfurther processing for rolled products and forgings.Certificate No. MD00/0041/0006/1 Expiry date: 02/06/2014
As belowE.A.F./Ingot/Con CastSteelmakingACCIAIERIE VALBRUNA S.P.A. Veniceas belowA.O.D./Ingot/Con Castaustenitic stainless, duplex stainless,precipitation hardened stainless*, martensiticstainless*
73MachineryBars
As at 06 November 2012 35Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR OfficeVia A Volta 439100 Bolzano39100 Bolzano* Accepted for approved applicationsTel; +39 (0)471 924111 Fax: +39 (0)471 924355Email: mailto:[email protected] Web: http//www.acciaierie-valbruna.itCertificate No. MD00/2994/0004/1 Expiry date: 26/06/2015
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingACCIAIERIE VENETE S.p.A. Venicecarbon, carbon manganese, Alloy 280Blooms/BilletsSemi-FinishedCarbon, Carbon-manganese, Alloy 600As Cast Round Sectioncarbon, carbon-manganese, alloy 200Semi-finished ProductsBarscarbon, carbon-manganese, alloy 180Structuralcarbon, carbon-manganese, alloy 130Machinery
35020 Camin (Padova)
Camin WorksRiviera Francia, 9
Tel +39 (0)49 8282 820 Fax +39 (0)49 8282 666 Email: mailto:[email protected] Web: http://www.acciaierievenete.comCertificate No. MD00/0042/0006/1 Expiry date: 26/03/2015
Approval does not cover bars with a diameter of less than 65mm.
As belowE.A.F. / Con CastSteelmakingAFV ACCIAIERIE BELTRAME S.p.A. VeniceNormal strength, Higher Strength 220SlabsSemi-FinishedA, B, D, E 20Normal StrengthSectionsAH32, AH36, DH32, DH36 20Higher Strength
Viale della Scienza 81/A36100 VicenzaTel +39 0444 967111 Fax +39 0444 967137Email: mailto:[email protected] Web site http://www.beltrame.itCertificate No. MD00/0047/0007/1 Expiry date: 22/02/2015
A, B, D, E 40Normal StrengthBarsAFV ACCIAIERIE BELTRAME S.p.A. VeniceAH27S, AH32, AH36, DH27S, DH32, DH36 40Higher Strength
Via del Commercio, 1530175 Marghera (VE)
Stabilimento di Marghera
Tel +39 041 2583711 Fax +39 041 2583819 E-mail:mailto:[email protected] www.beltame.itCertificate No. MD00/1374/0006/1 Expiry date: 09/02/2015 *Enhanced Survey*
A, B, D 8Normal StrengthSectionsAFV ACCIAIERIE BELTRAME S.p.A. ViareggioAH32, AH36, DH32, DH36 8Higher Strength
Piazza Matteotti 13,52027 S.Giovanni Valdarno (AR)
S.Giovanni Valdarno Plant
Tel No: +39 (0) 444 967125 Fax + 39 (0) 444 967137Email [email protected]:www.beltrame.itCertificate no MD00/37710001/1 Expiry date: 07/04/2013
A, B, D 22Normal StrengthFabricated SectionsARMANDO CIMOLAI CENTRO SERVIZI Srl TriesteAH32, AH36, DH32, DH36 22Higher Strength
Via Masieres, No.3233080 San Quirino (PN)Tel: +39 (0)434 919292 Fax: +39 (0)434 919266Email: [email protected] No. MD00/2620/0005/1 Expiry date: 01/12/2014
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingASO SIDERURGICA S.r.L. Bresciacarbon, carbon-manganese, alloy 65IngotsSemi-Finished
25035 OspitalettoBrescia
UnipersonaleVia Seriola no. 122
Tel: +39 (0)30 6841011-(0)30 6841165 Fax: +39 (0)30 6841012 Email: mailto:[email protected] Web: http://www.aso.itCertificate No. MD00/0020/0005/1 Expiry date: 15/04/2014
A, B, D 22Normal StrengthFabricated SectionsCIMOLAI S.p.A TriesteAH32, AH36, DH32, DH36 22Higher Strength
Via Tessere 933070 - Polcenigo (PN)Tel: +39 (0)434 748822 Fax: +39 (0)434 749139 Email mailto:[email protected] Web http://www.cimolai.comCertificate No. MD00/2617/0005/1 Expiry date: 01/12/2011
austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingCOGNE ACCIAI SPECIALI S.p.a Milanmartensitic stainless*E.A.F. / Ingotaustenitic stainless, duplex stainless 4IngotsSemi-FinishedMartensitic Stainless Steel* 160Billetsaustenitic stainless, duplex stainless 270Martensitic Stainless Steel* 220Bars
As at 06 November 2012 36Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR OfficeVia Paravera,1611100 AOSTATel No: +39 165 3021 Fax no: +39 165 302423Email: [email protected] site: www.cogne.comCertificate No.MD00/3809/0001/1 Expiry date 14/07/2013
A, D 50Normal StrengthFabricated SectionsEUROGROUP S.p.A. TriesteAH36, DH36 50Higher Strength
34074 MONFALCONE (GO)Via Timavo - Z. I. Lisert
Tel: +39 481 495111 Fax: +39 481 495112 Email: [email protected] Web: http://www.eurogroupspa.comCertificate No. MD00/2781/0004/1 Expiry date: 19/02/2013
A 30Normal StrengthPlatesEVRAZ PALINI E BERTOLI S.P.A. TriesteAH32, AH36 30Higher Strength
Via E. Fermi, 28 - 33058San Giorgio di Nogaro (UD)Tel: +39 0431 62 3111 Fax: +39 0431 62 1244 Email: [email protected] web: www.paliniebertoli.itCertificate No. MD00/1809/0007/1 Expiry date: 09/06/2014
A 20Normal StrengthFabricated SectionsG. BAGLIETTO S.a.s. NAVAL STEEL GenoaAH36, DH36, EH36 20Higher Strength
Novi Ligure (AL)Via Castelgazzo 11
Certificate No. MD00/3910/0001/1 Expiry date: 16.05.2014
As belowB.O.S. / Con CastSteelmakingILVA S.p.A. TarantoNormal strength, Higher Strength 303SlabsSemi-FinishedA, B, D, E 80Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80Higher Strength
A 10Normal StrengthHot Rolled CoilAH27S, AH32, AH36 10Higher Strength
Via Appia KM 648Taranto 74100
Taranto Works
Tel: +39 02 307 00 775 Fax: +39 02 307 00 285 Email: mailto:[email protected] Web: http://www.rivagroup.comSpecified through thickness properties for grade D, E, AH, DH and EH notation Z35 may be addedCertificate No. MD00/2276/0006/1 Expiry date: 11/10/2015
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingLUCCHINI RS S.p.A. Brescia
Via G. Paglia N.4524065 Lovere
Tel: +39 035 963535 Fax: +39 035 963488 Email: mailto:[email protected] Web: http://www.lucchiniRS.itCertificate No. MD00/0949/0007/1 Expiry date: 19/03/2015
Bergamo
A, B, D, E 60Normal StrengthPlatesMETINVEST TRAMETAL S.p.A. TriesteAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
60Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 60Boiler & Pressure VesselVia Enrico Fermi, 4433058 San Giorgio di Nogaro (UD)
Approved for Z grade plates with specified through thickness properties when tested in accordance with Rules requirements.
Tel: +39 010 57 62911 Fax: +39 010 57 62990 Email:mailto:[email protected] Web:http://www.trametal.itCertificate No. MD00/2004/0007/1 Expiry date: 02/08/2014
As belowE.A.F. / IngotSteelmakingNLMK VERONA Venicecarbon, carbon-manganese 32IngotsSemi-Finished
Via A, Salieri, 22,37050 Vallese di Oppeano (Verona)Tel: +39 045 699 7900 Fax: +39 045 699 7901 email: [email protected] Web: http://www.eu.nlmk.com/verona/Ingots as semi finished products are approved for further processing for forgings to the above maximum weight. Round and Polygon ingots to nominalmaximum dimensions of 1200mm diameter x 4750mm length, oblong ingots to nominal maximum dimensions 970mm x 870mm x 2050mm.Certificate Number MD00/3985/0001/1 Expiry date: 31/01/2015
A, B, D, E 50Normal StrengthFabricated SectionsOFFICINE NORD EST S.r.l TriesteAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
Via Ungaresca No.1233080 San Quirino (Pn)Tel: +39 (0)434 919091 Fax: +39 (0)434 918646 Email to: [email protected] Certificate No. MD00/2626/0006/1 Expiry date: 07/12/2014
As at 06 November 2012 37Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D 8Normal StrengthSectionsOLIFER-ACP S.P.A. BresciaAH32, AH36, DH32, DH36 8Higher Strength
Loc.Motta Alta, 1424050 Cividate Al Piano
ROLLING MILL - ODOLOBrescia Work
Tel +39 365 826088 Fax +39 365 860727 Email: mailto:[email protected] Web:http://www.olifer.comCertificate No. MD00/1147/0007/1 Expiry date: 31/03/2015
Bergamo
As belowE.A.F./Ingot/Con CastSteelmakingOLIFER-ACP S.P.A. Bresciacarbon, carbon-manganese, alloy 54IngotsSemi-Finishedcarbon, carbon-manganese 120Blooms/Billets
Loc. Motta Alta 14Cividate Al Piano
STEELMAKINGBergamo Works
Tel: +39 363 97193/4 Fax: +39 363 976666 Email: mailto:[email protected] Web http://www.olifer.comCertificate No. MD00/1807/0007/1 Expiry date: 12/03/2015
A 25Normal StrengthFabricated SectionsPALESCANDOLO SPA NaplesAH32, AH36 25Higher Strength
Via Boscofangone, zone A.S.I., NolaCertificate No. MD00/3850/0001/1 Expiry date: 31/10/2013
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
30Higher StrengthSectionsSIDERVAL S.P.A. Milan
Via Roma 39C23018 Talamona
Tel: +39 342 674125 Fax: +39 342 670400 Email: mailto:[email protected] Web: http://www.siderval.itCertificate No. MD00/2857/0004/1 Expiry date: 16/01/2014
Sondrio
Japan
carbon, carbon-manganese, austenitic stainlessE.A.F. / IngotSteelmakingAICHI STEEL CORPORATION Kobealloy 190BarsSemi-FinishedA 180Normal StrengthBars304L, 316L 180Austenitic Stainlesscarbon, carbon-manganese, alloy, austeniticstainless
125Machinery
U1, U2, U3 120Chain Cable Stock
Arao-machiTokai-shi
Chita Plant1, Wano-Wari
Tel: +81 52 603 9353 Fax: +81 52 603 9898 Email: mailto:[email protected]: www.aichi-steel.co.jpCertificate No. MD00/0076/0007/1 Expiry date: 24/09/2015
Aichi-ken, 476-8666
304L, 316L 150Austenitic StainlessBarsAICHI STEEL CORPORATION Kobe
Kariya-shiAichi-ken
Kariya Plant3-6, Toyota-cho
Tel +81 566 21 9130 Fax +81 566 23 6925 Email: mailto:[email protected] www. aichi-steel.co.jpCertificate No. MD00/0078/0006/1 Expiry date: 23/09/2015
448-0848
As belowE.A.F. / IngotSteelmakingASIA SPECIAL STEEL CO. LTD. Nagasakicarbon, carbon-manganese, alloy 48IngotsSemi-Finished
43-1 Koyomachi, Wakamatsu-ku,Kitakyushu, Fukuoka 808-0002,Tel: +93 482 2222 Fax: +93 482 2227 Email: [email protected] Web: www.asiass.co,jpSemi finished products as ingots, nominal 1600mm diameter x 3100mm high to maximum weight shown above, are approved for further processing forgings.The scope of approval also includes for the provision of molten steel for production of steel castings to Kotobuki Industries Co. Ltd. Kitakyushu Works (LRPlant Reference M3800).Certifcate Number: MN00/3796/0003/1 Expiry date: 29/06/2013
As at 06 November 2012 38Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingCHUBU STEEL PLATE CO., LTD. KobeA, B 50Normal StrengthPlates360AR, 410AR 40Boiler & Pressure Vessel
Nakagawa-kuNagoya
5-1, Kousudori
Tel: +81 52 661 3818 Fax: +81 52 661 2265 Email: mailto:[email protected] Web http://www.chubukokan.co.jpCertificate No. MD00/0309/0006/1 Expiry date: 20/04/2014
As belowE.A.F. / IngotSteelmakingDAIDO STEEL CO., LTD. Kobecarbon, carbon-manganese 7IngotsSemi-Finishedcarbon, carbon-manganese 275Bloomscarbon, carbon-manganese 148Billetscarbon, carbon-manganese 270StructuralBars
39, Motohama-machiTokai-shi
Chita Plant
Tel: +81 562 33 3106 Fax: +81 562 33 6598 Email:[email protected] Web: http://www.daido.co.jpCertificate No. MD00/0372/0005/1 Expiry date: 21/03/2014
Aichi-ken
carbon, carbon-manganese 160StructuralBarsDAIDO STEEL CO., LTD. Kobecarbon, carbon-manganese 160Machinery
Minami-kuNagoya-shi
Hoshizaki Plant2-30, Daido-cho
Tel: +81 52 611 2525 Fax: +81 52 611 2528 EMail:[email protected] Web:http://www.daido.co.jpCertificate No. MD00/0373/0005/1 Expiry date: 27/02/2014
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingDAIDO STEEL CO., LTD. Yokohama
Shibukawa-shiGunma 377-0007
Shibukawa Plant500, Ishihara
Tel: +81 279 25 2009 Fax: +81 279 25 2043 Email: mailto:[email protected] No. MD00/0375/0005/1 Expiry date: 27/11/2012
As belowE.A.F. / Con CastSteelmakingDAISAN STEEL Co., Ltd. YokohamaNormal Strength 170BilletsSemi-FinishedA, B 28Normal StrengthBars
Kohto-kuTokyo 136-0075
Shinsuna Works3-2-1, Shinsuna
Tel: +81 (0)3 3644 1101 Fax: +81 (0)3 3664 1100 Email: mailto:[email protected]: www.daisan-seiko.co.jpCertificate No. MD00/0381/0006/1 Expiry date: 26/02/2015
As belowE.A.F. / Con CastSteelmakingGODO STEEL LTD. Kobecarbon, carbon-manganese 490SlabsSemi-FinishedA 15Normal StrengthSectionsA 150Normal StrengthBarsU3 100Chain Cable StockU1, U2 150
Hyogo pref.
2946 Nakashima ShikamakuHimeji-city
Tel. +81 (0)792 34 9332 Fax +81(0)792 34 9538Certificate No. MD00/0606/0006/1 Expiry date: 06/08/2015
As belowE.A.F. / IngotSteelmakingHITACHI METALS, LTD. KobeA 150Normal StrengthBarsalloy, austenitic stainless 150Structural
Yasugi-shiShimane-ken
Yasugi Works2107-2, Yasugi-cho
Tel: +81 (0) 854 22 1908 Fax: +81 (0)854 23 0281 Email mailto:[email protected] Web http://www.hitachi-metals.co.jpCertificate No. MD00/0678/0005/1 Expiry date: 20/12/2012
As below, carbon, carbon-manganeseE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION Kobecarbon, carbon manganese 300Blooms/BilletsSemi-FinishedB, D, E 25Normal StrengthSectionsA 32EH32, EH36 25Higher StrengthAH32, AH36, DH32, DH36 32
As at 06 November 2012 39Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
1280, HosoeShikama-ku
Himeji Works
Tel +81 (0)792 35 6376 Fax +81 (0)792 35 2048 email: mailto:[email protected] Internet http://www.jfe-bs.co.jpCertificate No. MD00/1535/0006/1 Expiry date: 27/08/2012
Himeji 672-8064
As belowE.A.F. / Con CastSteelmakingJFE BARS & SHAPES CORPORATION Yokohamacarbon, carbon-manganese 150BilletsSemi-FinishedA 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher Strength
Ibaraki Pref.314-0111
Kashima Works7 Minamihama, Kamisu-city
Tel: +81 (0)299 90 5218 Fax: +81 (0)299 90 5201 Email: mailto:[email protected] finished products as billets to nominal 150mm width and 12000mm nominal length to the maximum thickness shown above are approved for furtherprocessing for rolled products.Certificate No. MD00/1920/0005/1 Expiry date: 29/01/2014
As BelowB.O.S./E.A.F./Ingot/Con CastSteelmakingJFE STEEL CORPORATION KobeA, B, D, E 200Normal StrengthPlatesAH42, FH27S, FH32, FH36 50Higher StrengthDH42, DH46, DH50, DH55, DH62, DH69, EH42,EH46, EH50, EH55, EH62, EH69
75
AH40, DH40, EH40 80AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
150
360AR, 410AR 40Boiler & Pressure Vessel360, 410 100360FG, 410FG, 460FG, 490FG, 510FG 1349Ni 40Ferritic Low TemperatureLTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50
304L, 316L 50Austenitic StainlessE/304L, E/316L 30CladA, B, D, AH27S, AH32, AH36, DH27S, DH32,DH36, EH27S, EH32, EH36
50Tapered
A, B, D, AH27S, AH32, DH27S, DH32 40Differential ThicknessA, B 16Normal StrengthHot Rolled Coil360, 410 16Boiler & Pressure VesselA, B, D 32Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
32Higher Strength
carbon, carbon-manganese 400StructuralBarsalloy 165Machinerycarbon-manganese 190U1, U2 130Chain Cable Stock
Kawasaki-DoriKurashiki
West Japan Works (Kurashiki)1 Mizushima
Tel: +81 (0)86 447 2730 Fax: +81 (0)86 447 2735 Email: mailto:[email protected] through thickness properties on all plate grades.Certificate No. MD00/0838/0021/1 Expiry date: 16/11/2012
MQS Approved - Approval No. MQS 022
As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION KobeA, B, D, E 120Normal StrengthPlatesAH32S 55Higher StrengthAH46S*, DH46S*, EH46S* 75AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40, FH27S,FH32, FH36, FH40
80
360AR, 410AR 40Boiler & Pressure Vessel460FG, 490FG, 510FG 55360FG, 410FG 70LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36
40Ferritic Low Temperature
304L, 304LN, 316L, 316LN, 317L, 317LN 55Austenitic StainlessA to EH36/304L, A to EH36/316L 30CladA, DH34S, EH34S, B, D, A,B, A,B,D,E, AH32,AH36, DH32, DH36, EH32, EH36, AH34S
50Differential Thickness
A, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32 8Higher Strength460FG, 490FG 8Boiler & Pressure Vessel
As at 06 November 2012 40Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Japan360, 410, 360FG, 410FG 12Boiler & Pressure VesselHot Rolled CoilJFE STEEL CORPORATION KobeE 18Normal StrengthSectionsA, B, D 35AH40, DH40, EH40, FH27S, FH32, FH36 18Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
36
LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36
18Ferritic Low Temperature
Fukuyama-cityHiroshima-pref.
West Japan Works (Fukuyama)1, Kokan-cho
Tel. (0)84 945 3160 Fax (0)84 945 3101 EMail mailto:[email protected] Web http://www.jfe-steel.co.jp
MQS Approved - Approval No. MQS 005Certificate No. MD00/1055/0010/1 Expiry date: 17/10/2012
721-8510
As belowB.O.S. / Con CastSteelmakingJFE STEEL CORPORATION YokohamaA, B, D, E 100Normal StrengthPlatesFH27S, FH32, FH36 42Higher StrengthAH42, DH42, EH42 83AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
90
360AR, 410AR 40Boiler & Pressure Vessel360, 410, 460FG, 490FG, 510FG 50360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
42Ferritic Low Temperature
D, E 40Normal StrengthTapered Plates maxA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, AH40, DH40, EH40
50Higher Strength
AH32, AH36 22Higher strengthTapered Plates max
Kawasaki-kuKawasaki
East Japan Works (Keihin)1-1, Ohgishima
Tel: +81 44 322 1185 Fax: +81 44 322 1510 Email: mailto:[email protected] plate grades with specified through thickness properties.Materials Quality Scheme Approved - Approval No. MQS 034Certificate No. D00/1056/0007/1 Expiry date: 30/10/2012
210-0868
austenitic stainlessB.O.S/V.O.D./Con CastSteelmakingJFE STEEL CORPORATION Yokohamaaustenitic stainless 275SlabsSemi-Finished
Chuo-kuChiba 260-0835
East Japan Works (Chiba)1, Kawasaki-cho
Tel: +81 43 262 2287 Fax: +81 43 262 2980 Email to: [email protected]
Certificate No.: MD00/4065/0001/1 Expiry Date: 07/08/2015
As belowB.O.S. / Con CastSteelmakingKOBE STEEL LTD. KobeAs belowB.O.S. / IngotAs belowE.A.F. / Con CastAs belowE.A.F. / IngotA, B, D, E 150Normal StrengthPlatesDH42, DH50, DH55, DH62, DH69, EH42, EH50,EH55, EH62, EH69, FH40, FH42, FH46, FH50,FH55, FH62, FH69
50Higher Strength
AH46, DH46, EH46 60AH40, DH40, EH40 80FH27S, FH32, FH36 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 460FG, 490FG, 510FG 90360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
90Ferritic Low Temperature
A,B, D,E, HTS up to EH36 50Differential ThicknessA, B, D 13Normal StrengthHot Rolled Coil
As at 06 November 2012 41Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Japan360FG, 410FG 13Boiler & Pressure VesselHot Rolled CoilKOBE STEEL LTD. Kobe
1 Kanazawa-choKakogawa-city
Kakogawa Works
Tel: +81 794 36 1151 Fax: +81 794 36 2079 Email: mailto:[email protected] grades with specified through thickness properties.Certificate No. MD00/0863/0008/1 Expiry date: 16/10/2012
Materials Quality Scheme Approved - Approval No. MQS 009
Hyogo-pref.
As belowB.O.S./Ingot/Con CastSteelmakingKOBE STEEL LTD. Kobecarbon, carbon-manganese, alloy 8IngotsSemi-FinishedCarbon, Carbon-Manganese, Alloy 600Rolled Bloomscarbon, carbon-manganese, alloy 250Semi-finished ProductsBarsA 250Normal Strengthcarbon, carbon-manganese, alloy 250MachineryU1, U2, U3 160Chain Cable Stock
Nada-kuKobe
Kobe Works2 Nadahama-Higashimachi
Tel +81 78 882 8056 Fax +81 78 882 8204 Email: mailto:[email protected] No. MD00/0864/0007/1 Expiry date: 08/08/2014
As belowE.A.F. / Con CastSteelmakingKYOEI STEEL LTD. NagasakiA 16Normal StrengthSectionsA 53Normal StrengthBars
Sanyo-Onoda CityYamaguchi Prefecture
Yamaguchi DivisionOaza Onoda 6289-18
Tel: +81 836 83 6172 Fax: +81 836 83 0839 Email mailto:[email protected] Web http://www.kyoeisteel.co.jpCertificate No. MD00/1892/0005/1 Expiry date: 21/03/2013
756-0817
As belowE.A.F. / IngotSteelmakingMITSUBISHI STEEL MFG. CO., LTD. Yokohamacarbon, carbon-manganese 16IngotsSemi-Finished
Hirota, Kawahigashi-machiAizuwakamatsu-city
Hirota Works405, Aza Rokucho
tel: +81 (0) 242 75 3111 Fax: +81 (0) 242 75 2619 Email mail to: [email protected] or [email protected] Web:http://www.mitsubishisteel.co.jpIngots nominal 2050mm diameter x nominal 1250mm length to the above maximum weight are approved for further processing forgings.Certificate Number: MD00/1802/0001/1 Expiry: 03/03/2015
Fukushima Pref. 969-3471
as below 20IngotsSemi-FinishedMITSUBISHI STEEL MURORAN INC. YokohamaAs below 515Blooms/Billetscarbon, carbon-manganese, alloy 270StructuralBarscarbon, carbon-manganese, alloy 210Machinery
Muroran shiHokkaido
Muroran Works12, Nakamachi
Tel: +81 (0)143 41 2838 Fax: +81 (0)143 41 2869 Email mailto:[email protected] No. MD00/1893/0006/1 Expiry date: 09/04/2013
050-0087
A 38Normal StrengthBarsNIHON STEEL CO., LTD. Kobe11, Rinkai-choKishiwada City
tel: +81 724 23 5151 Fax: +81 724 39 8357 Email mailto:[email protected] No. MD00/2299/0004/1 Expiry date: 12/03/2011
Osaka
As belowE.A.F. / Con CastSteelmakingNIPPON METAL INDUSTRY CO., LTD. Kobe304L, 316L, 321, 347 8Austenitic StainlessHot Rolled Coil
Hekinan-shiAichi- ken
Kinuura Works1, Hama-cho
Tel: +81 566 48 7218 Fax: +81 566 48 1596 Email: mailto:[email protected] No. MD00/2338/0006/1 Expiry date: 26/05/2014
447-8610
As at 06 November 2012 42Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347, 304*, 316*
55Austenitic StainlessPlatesNIPPON STEEL & SUMIKIN Nagasaki
UNS S31803 40Duplex StainlessA/304L, D/304L, D/316L 40Clad
2108-1, Oaza Maeda Aza HatoYawata Higashi-ku
STAINLESS STEEL CORPORATIONYawata Works
* Grades 304,.and 316 may be accepted for approved applications.Tel; +81 93 672 2290 Fax: +81 93 672 2251 Email: mailto:[email protected]: ns-sc.co.jp/en/company/plants/yawata.phpCertificate No. MD00/1105/0009/1 Expiry date: 23/05/2015
Kitakyushu City, Fukuoka Pref.
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / Con CastSteelmakingNIPPON STEEL & SUMIKIN Nagasaki
austenitic stainless 236SlabsSemi-Finished304L, 316L 8Austenitic StainlessPlates304L, 316L 8Austenitic StainlessHot Rolled Coil
3434 ShimataHikari City
STAINLESS STEEL CORPORATIONProduction Division, Hikari Works
Tel +81 833 71 5184 Fax +81 833 71 5215 Email: mailto:[email protected] Web: http://www.ns-sc.co.jpCertificate No. MD00/3196/0003/1 Expiry date: 25/10/2014
Yamaguchi 743-8550
As belowB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Yokohama
As belowSlabsSemi-Finished
carbon, carbon-manganese 300
carbon, carbon-manganese, alloy 165Blooms/Billets
A, B, D, E 100Normal StrengthPlates
AH42, DH42, EH42, FH42 50Higher Strength
AH46, AH50, DH46, DH50, EH46, EH50, FH46,FH50
70
AH40, DH40, EH40, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
100
360AR, 410AR 40Boiler & Pressure Vessel
360FG, 410FG, 460FG, 490FG, 510FG 100
LHAH42, LTAH46, LTAH50, LTDH42, LTDH46,LTDH50, LTEH42, LTEH46, LTEH50, LTFH42,LTFH46, LTFH50
50Ferritic Low Temperature
LTAH40, LTDH40, LTEH40, LTFH40 80
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
100
A,B,D,E, HTS up to EH40 50Tapered
A,B,D,E, HTS up to EH40 50Differential Thickness
A, B, D 24Normal StrengthSections
AH27S, AH32, AH36, DH27S, DH32, DH36 19Higher Strength
A, B 12Normal StrengthPlates from coils
360, 410 12Boiler and Pressure Vessel
A, B 25Normal StrengthHot Coiled Strip
360, 410 25Boiler & Pressure Vessel
As at 06 November 2012 43Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Kimitsu-shiChiba-ken
Kimitsu Works1 Kimitsu
Materials Quality Scheme approved - MQS001
Materials Quality Scheme covers Steelmaking and rolled plates only. Strip, plate cut from coil and sections approved under Materials Survey Scheme (directsurvey).
All plate grades with specified through thickness properties.Tapered plates in transverse and longditudinal directions.
High strength fine grained Ti+Nb steel plates produced in the TM + Acc and TM + Acc + Temper conditions up to 70mm thickness are approved with Mn andAl contents to be outside that given in Lloyd's Register Materials Rules. Letter 'S' is used after identification number of non-standard composition materials.
Tel: +81 (0)439 50 2194 Fax: +81 (0)439 55 8727 Email: mailto:[email protected] Web http://www.nsc.co.jp/kimitsu/
Certificate No. MD00/1100/0011/1 Expiry date: 18/06/2014
299-1141
As BelowB.O.S./E.A.F./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Yokohama
carbon, carbon-manganese, alloy 190BilletsSemi-Finished
A, B 200Normal StrengthBars
AH32, AH36, DH32 200Higher Strength
U1, U2, U3, R3, R3S, R4 136Chain Cable Stock
API-2F 152
Muroran CityHokkaido
Muroran Works12, Naka-machi
Tel: +81 (0)143 47 2337 Fax: +81 (0)143 47 2783 Email: maruyama.kenichi.nsc.co.jp Web: http://www.nsc.co.jp/muroranThe approval for bars intended for chain cable stock are for material rolled from continuous casting billets only.Bars for mooring grade chain cable stock in grades R3, R3S and R4 are restricted to Hamanaka Chain Mfg. Co. Ltd. Himeji plant only.Bars in Grade U3 in the above supply condition may be accepted up to 200mm diameter for the further processing for the production of forged chain cablefittings.Approval for billets, maximum 190mm x 190mm x 8000mm maximum weight 2.3 Tonnes, as semi finished products are for further processing for forgings.Certificate Number: MD00/1101/0011/1 Expiry date: 02/07/2014
050-8550
As belowB.O.S./Ingot/Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
A, B, D, E 130Normal StrengthPlates
FH27S 40Higher Strength
AH40, DH40 50
DH42, DH46, EH40, EH42, FH32, FH36, FH40,FH42
70
EH46, EH46S*, FH46, FH46S* 110
DH50, DH55, DH62, DH69 200
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
210
360AR, 410AR 40Boiler & Pressure Vessel
360, 410 115
360FG, 410FG, 460FG, 490FG, 510FG 120
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
40Ferritic Low Temperature
Tokai-machiTokai-city
Nagoya Works3, 5 Chome
Tel +81 52 603 7225 Fax +81 52 603 7229 Email: [email protected] grades and thicknesses with specified through thickness properties (Z35)Certificate No. MD00/1102/0009/1 Expiry date: 17/07/2013
Aichi Pref. 476-8686
As at 06 November 2012 44Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Nagasaki
A, B, D, E 100Normal StrengthPlates
DH42, EH42, FH42 50Higher Strength
EH40S* 60
AH47, DH47, EH47, AH47-W430, DH47-W430,EH47-W430, EH47-W140, DH47-W140,AH47-W140
70
AH40, DH40, EH40, FH27S, FH32, FH36, FH40 80
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360AR, 410AR, 460AR 40Boiler & Pressure Vessel
360, 410, 460, 490 90
360FG, 410FG, 460FG, 490FG, 510FG 100
LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40
80Ferritic Low Temperature
A, B, D, E, A,B,D,E, AH27S, AH32, AH36,DH27S, DH32, DH36, EH27S, EH32, EH36
50Tapered
A,B,D 35Differential Thickness
A,B, A,B,D,E, AH27S, AH32, AH36, DH27S,DH32, DH36, EH27S, EH32, EH36
50
A 12Normal StrengthHot Rolled Coil
AH27S, AH32, AH36 12Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 12Boiler & Pressure Vessel
Oita CityOita Prefecture
Oita Works1, Oaza Nishinotsu
Tel +81 97 553 2122 Fax +81 97 553 2379 Email: mailto:[email protected] Web http://www.nsc.co.jp/oita/All plates with specified through thickness properties except H47 grades.* Plates in LLF27 and LLF33 up to a maximum thickness of 40 mm can be accepted for approved applications.* Plates in EH40S are for approved applications only and may have a Nickel content up to 1.5% with a carbon equivalent of 0.4%. The Approved thicknessrange of EH40S is 30mm to 60mm.* Plates in the H47 grades to be produced to the agreed chemistry ranges and agreed max CEVs.
Materials Quality Scheme Approved - Approval No. MQS010Certificate No. MD00/1103/0015/1 Expiry date: 31/03/2013
A, B, D, E 50Normal StrengthSectionsNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
AH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
1, Chikko Yawata-cho Sakai-KuSakai City
Sakai Works
Tel: +81 722 33 1179 Fax: +81 722 33 1185 Certificate No. MD00/1104/0005/1 Expiry date: 09/07/2012
Osaka
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Yokohama
austenitic stainlessA.O.D./Con Cast
A, B, D, E 150Normal StrengthPlates
AH32S 30Higher Strength
FH27S 32
FH32, FH36 40
AH42, AH46, AH50, AH55, AH62, DH42, DH46,DH50, DH55, DH62
47
AH36S, AH40S, DH36S, DH40S, EH36S, EH40S 50
AH36, AH40, DH36, DH40, EH27S, EH32, EH36,EH40
105
As at 06 November 2012 45Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
JapanAH27S, AH32, DH27S, DH32 150Higher StrengthPlatesNIPPON STEEL & SUMITOMO METAL
CORPORATIONYokohama
360AR, 410AR, 460AR 40Boiler & Pressure Vessel
510FG 55
360, 410, 460, 490 63
360FG, 410FG, 460FG, 490FG 100
3.5Ni, 5Ni 30Ferritic Low Temperature
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
45
EH36/304L, EH36/316L 38Clad
EH27S, EH32, EH36 32Differential Thickness
A,B,D, AH27S, AH32, AH36, DH27S, DH32,DH36
35
A, B, D, E 35Normal StrengthSections
AH40, DH40, EH27S, EH32, EH36 18Higher Strength
DH27S, DH32, DH36 20
AH27S, AH32, AH36 35
A, B, D 19Normal StrengthHot Coiled Strip
360FG, 360, 410FG, 410 19Boiler & Pressure Vessel
Kashima CityIbaraki Pref.
Kashima Works3 Hikari
Tel +81 (0)299 84 2573 Fax +81 299 84 2945Email mailto: [email protected] Web http://www.sumitomometals.co.jpAll plates with specified through thickness properties.
Materials Quality Scheme Approved - Approval No. MQS 002
SMI's Fatigue Crack Arrester (FCA) grades by the DAC process with parent plate fatigue crack growth rates guaranteed by the manufacturer and tested inaccordance with ASTM E647 may be accepted for approved applications. Properties are to be as agreed with the Society. This acceptance does not implyconcessions on either design or survey requirements.
SMI's High Welding Heat Input Steel, may be accepted for approved applications, in all higher tensile strength grades up to EH40, in the TM + ACC conditionup to 105 mm thickness, when used in accordance with SMI's guidelines for welding or line heating. This acceptance does not imply concessions on eitherdesign or survey requirements.
SMICORE, may be accepted for approved applications, in all higher tensile strength grades up to EH36, in the TM condition up to 20mm thickness and the TM+ ACC condition up to 30 mm thickness. The steel is to have a guaranteed CRL of 0.5 or less and to be of approved composition. This acceptance does notimply concessions on either design or survey requirements.(Note CRL = Corrosion Ratio by Long term test)Certificate No. MD00/1454/0016/1 Expiry date: 09/07/2013
314-0014
A 240Normal StrengthBarsNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
1, Nishino-choHigashi-Mukojima
Pipe & Tube UnitAmagasaki Works
Tel: +81 (0)6 6411 7616 Fax: +81 (0)6 6411 7612 Email: mailto:[email protected] No. MD00/1458/0007/1 Expiry date: 14/11/2013
Amagasaki, 660-0856
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingNIPPON STEEL & SUMITOMO METALCORPORATION
Kobe
austenitic stainlessA.O.D./Con Cast
As at 06 November 2012 46Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
1850 MinatoWakayama-city
Wakayama Works
Tel: +81 (0) 73451 1133 Fax: +81 734 51 1103 EMail: mailto:[email protected] Sales fax +81 34416 6789 Web: www.sumitomometals.co.jpCertificate No. MD00/1748/0009/1 Expiry date: 26/06/2013
640-8555
As belowE.A.F. / Con CastSteelmakingNIPPON YAKIN KOGYO Co., Ltd. YokohamaAs below, austenitic stainless 200SlabsSemi-Finished321, 347 10Austenitic StainlessPlates304L, 316L 53Fe-36Ni* 8Fe-Ni alloys304L, 316L, 321, 347 8Austenitic StainlessHot Rolled CoilFe-36Ni* 3Fe-Ni alloys
Kawasaki-kuKawasaki-shi
KAWASAKI PLANT4-2, Kojima-cho
Tel: +81 44 271 3045 Fax: +81 44 271 3034Email mailto:[email protected] Web http//www.nyk.co.jp* accepted for approved applicationsCertificate No. MD00/1109/0007/1 Expiry date: 01/06/2015
Kanagawa - ken 210-8558
As belowE.A.F. / Con CastSteelmakingOJI STEEL CO., LTD. Yokohamacarbon, carbon-manganese 170BilletsSemi-FinishedA 25Normal StrengthBarsAH32, AH36 25Higher Strength
Ota-cityGunma Pref.
Gunma Works120, Nittasorimachi-cho
Tel: +81 276 56 2119 Fax: +81 276 56 3136 Email: mailto:[email protected]: www. oji-steel.co.jpCertificate No. MD00/1141/0006/1 Expiry date: 15/10/2014
370-0313
AE.A.F. / Con CastSteelmakingOSAKA STEEL CO., LTD. KobeA 185BilletsSemi-Finished
1 Chikko Yawata-choSakai
Sakai Works
Tel +81 722 33 3901 Fax +81 722 33 3976Certificate No. MD00/0821/0006/1 Expiry date: 20/06/2013
Osaka
As belowE.A.F. / Con CastSteelmakingOSAKA STEEL CO., LTD. KobeA, B, D 15Normal StrengthSectionsAH32, AH36 12Higher Strength
9-3 Minami Okajima 1 ChomeTaisho-ku
Osaka - Okajima Works
Tel: +81 06 6552 1447 Fax: +81 06 6552 3184 Email: [email protected] :www.osaka-seitetu.co.jpCertificate No. MD00/1157/0005/1 Expiry date: 21/05/2013
Osaka 551-0021
alloyE.A.F. / Con CastSteelmakingSANYO SPECIAL STEEL CO., LTD., KobeAs belowE.A.F. / Ingotcarbon, carbon-manganese, austenitic stainless 15IngotsSemi-Finishedcarbon, carbon-manganese, alloy, austeniticstainless
380Blooms
A 220Normal StrengthBarsalloy 125MachineryU1, U2, U3 136Chain Cable Stock
Shikama-kuHimeji-shi
3007 Nakashima
Tel: +81 (0)792 35 6029 Fax: +81 (0)792 35 6027 Email: [email protected]: http://www.sanyo-steel.co.jpCertificate No. MD00/1307/0010/1 Expiry date: 3/11/2013
672-8677
As at 06 November 2012 47Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingSHINKANSAI STEEL CORPORATION KobeA, B, D 38Normal StrengthSectionsAH32, AH36, DH32, DH36 38Higher Strength
5, Shiohama-choSakai
Sakai Works
Tel: +81 (0)72 228 5121 Fax: +81 (0)72 228 7119 Email: mailto:[email protected] Web: http://www.shinkansai-steel.co.jpCertificate No. MD00/0823/0006/1 Expiry date: 15/11/2014
Osaka
As belowE.A.F. / Con CastSteelmakingSHINKANSAI STEEL CORPORATION KobeA, B, D 32Normal StrengthSectionsAH32, AH36, DH32, DH36 32Higher StrengthU1, U2, U3 80Chain Cable StockBars
4-26-1, Hoshida KitaKatano-shi
Hoshida Works
Tel: +81 (0)72 891 0624 Fax: +81 (0)72 893 1319 Email mailto:[email protected] Web http://www.shikansai-steel.co.jpCertificate No. MD00/1244/0007/1 Expiry date: 06/10/2015
As belowE.A.F. / IngotSteelmakingTHE JAPAN STEEL WORKS LTD. YokohamaA, B, D, E 50Normal StrengthPlatesAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50304L, 316L 65Austenitic StainlessAH32/304L, AH32/316L, AH32/316LN,AH32/317L
19Clad
AH32/S31803 30A/304L, B/304L, D/304L, E/304L, A/316L,B/316L, D/316L, E/316L
100
MuroranHokkaido
Muroran Plant4, Chatsu-machi
Tel +81 (0)143 22 0451 Fax +81 (0)143 22 5736 Email: mailto:[email protected] No. MD00/1507/0006/1 Expiry date: 11/11/2012
051-8505
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingTOKAI SPECIAL STEEL CO., LTD. Kobecarbon, carbon-manganese 370BloomsSemi-Finishedcarbon, carbon-manganese 155Billets
Tokai-MachiTokai-shi
3, 5-Chome
Tel +81 52 603 7236 Fax +81 52 603 7229 EMail: [email protected] No. MD00/1542/0005/1 Expiry date: 04/02/2014
Aichi-ken
As belowE.A.F. / Con CastSteelmakingTOKYO STEEL MANUFACTURING CO., LTD. NagasakiA, B, D 32Normal StrengthPlates360AR, 410AR 32Boiler & Pressure VesselA 24Normal StrengthSections
Wakamatsu-kuKitakyusyu City
Kyushu Plant3-5-1, Minami-Futajima
Tel: +81 93 701 2631 Fax: 81 93 791 2639 Email: mailto:[email protected] Web http://www.tokyosteel.co.jpCertificate No. MD00/1550/0008/1 Expiry date: 29/06/2014
Fukuoka 808-0109
As belowE.A.F. / Con CastSteelmakingTOPY INDUSTRIES, LTD. KobeE 20Normal StrengthSectionsA, B, D 35AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
20Higher Strength
LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
20Ferritic Low Temperature
A, B, D, E 50Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 50Higher Strength
As at 06 November 2012 48Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
1, Akemi-choToyohashi-shi
Toyohashi Works
Tel +81 532 25 1111 Fax +81 532 25 7401 Email: mailto: [email protected] web: http://www.topy.co.jpCertificate No. MD00/1555/0006/1 Expiry date: 18/06/2011
Aichi-ken
As belowE.A.F. / Con CastSteelmakingYAMATO STEEL CO., LTD. KobeA, B, D, E 25Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
25Higher Strength
380, Kibi, Ohtsu-kuHimeji City
Tel: +81 (0)79 273 0716 Fax: +81 (0)79 272 0914 Email mailto: [email protected] Web:http://www.yamatokogyo.co.jpCertificate No. MD00/1687/0009/1 Expiry date: 21/06/2014
Hyogo-pref.
Korea
304L, 304LN, 316L, 316LN, 317L, 317LN, 321,347
8Austenitic Stainless SteelPlates from coilsBUSAN STEEL CO., LTD. Busan Port
1538-2, Songjung-DongGangseo-GuTel: +82 51 (0)3251131 Certificate No. MD00/4028/0001/1 Expiry date: 24/06/2015
304L, 304LN, 316L, 316LN 80Austenitic StainlessPlatesDK CORPORATION UlsanUNS S31803, UNS 32900*, UNS 32205* 50Duplex Stainless
#612-1, Go Hyun RiChung Ha Myun
Tel: +82 54 245 3063 Fax: +82 54 245 3065 Email:mailto:[email protected] Web:http://www.dkcsteel.comCertificate No. MD00/2230/0005/1 Expiry date: 30/05/2013
Buk-Ku, Pohang Gyeongsangbuk-do
carbon-manganeseE.A.F. / Con CastSteelmakingDONGKUK STEEL MILL Co. Ltd. Ulsancarbon-manganese 480Blooms/BilletsSemi-FinishedD, E 50Normal StrengthPlatesA, B 83AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
50Higher Strength
460FG, 490FG, 510FG 35Boiler & Pressure Vessel360AR, 410AR 40360FG, 410FG 50LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
D 25Normal StrengthSectionsA, B 32AH27S, DH32 25Higher StrengthAH32, DH27S 32
880 Songdong-RiDaesong-Myun, Nam-Gu
Pohang Works
Tel: +82 542 715684 Fax: +82 542 715317 EMail: [email protected] Web page http://www.dongkuksteel.co.krCertificate No. MD00/0414/0012/1 Expiry date: 15/05/2013
Billets to 150 x 150mm, Blooms to 200 x 250 & 250 x 300, Beam Blanks to 400 x 480 x 120mm.
Pohang City, Kyungsangbuk-Do
A, B, D, E 83Normal StrengthPlatesDONGKUK STEEL MILL Co. Ltd. SeoulAH32, AH36, AH40, DH32, DH36, DH40, EH32,EH36, EH40
83Higher Strength
460AR 35Boiler & Pressure Vessel360AR, 410AR 40490FG 50460FG, 510FG 70360FG, 410FG 83
400, Hanjin-ri,Songak-eup, Dangjin-kun,
Dangjin Works
Tel: +82 (0) 41 351 4677 Fax: +82 (0) 41 351 4692 Email: [email protected] Web: http://dongkuksteel.comCertifcate Number: MD00/3773/0006/1 Expiry: 12/04/2013
Chungnam
As at 06 November 2012 49Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 20Normal StrengthPlates from coilsDONGYANG S.TEC. CO., LTD Ulsan#619-12, Munduk-Ri,Ocheon-Eup Nam-Gu,
Tel: +82 54 292 6181 Fax: +82 54 291 6548Certifcate Number: MD00/3840/0002/1 Expiry date: 27/09/2013
Pohang-city, Kyeongbuk,
A 15Normal StrengthSectionsDong il Steel Co., Ltd. Busan PortAH32, AH36 16Higher Strength
230-4 Hakjang-DongSasang-gu
Sasang Works
Tel: +82 (0) 51 313 2881 Fax: +82 (0) 51 313 2889 Email mailtio:[email protected] Web:http://www.dongilsteel.comCertificate No. MD00/3174/0004/1 Expiry date: 06/08/2014
Busan
B, D, E 18Normal StrengthSectionsFINE BESTEEL CO LTD ChangwonA 30AH27S, AH32, AH36 30Higher Strength
25-1 Ha-Ri, Changnyeong-Up,Changnyeong-Gun,
Tel: +82 (0)55 259 2000 / 2064 Fax: +82 (0)55 259 2060Email: [email protected] www.fine-besteel.comCertificate No. MD00/3659/0004/1 Expiry date: 08/09/2015
Gyeongnam,
As belowE.A.F. / IngotSteelmakingHAMSCO CO., LTD. Changwoncarbon, carbon-manganese, alloy 80IngotsSemi-Finished
San 93, Mokhyun-ri, Hyuchun-myunHamyang-kun
Tel: +82 55 964 8000 Fax: +82 55 964 8011 Mail to: [email protected] No. MD00/3872/0001/1 Expiry date: 05/01/2014
Kyungnam
As belowE.A.F./Ingot/Con CastSteelmakingHYUNDAI STEEL COMPANY Seoulcarbon, carbon-manganese, alloy 75IngotsSemi-Finishedcarbon, carbon-manganese 270Bloomscarbon, carbon-manganese 200BilletsA, B 32Normal StrengthSectionsAH27S, AH32, AH36 32Higher Strength
#1, Songhyun-DongDong-Ku
Inchon Plant
Tel: +82 32 760 2753 Fax: +82 32 760 2866 Email: [email protected] Web: http://www.hyundai-steel.comSections include flat bars up to 400 mm width.Approval for Ingots as Semi-finished Products, Ingots, is for further processing as Forgings.Blooms and Billets as semi finished products are approved for further processing for rolled products to maximum thickness shown above, to nominal width400mm for blooms, 200mm for billets and nominal 10000mm length.Certificate No. MD00/0754/0007/1 Expiry date: 03/01/2014
Inchon
As belowE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY Ulsancarbon, carbon-manganese, alloyBlooms/BilletsSemi-FinishedB, D, E 18Normal StrengthSectionsA 37AH27S, AH40, DH27S, DH40, EH27S, EH32,EH36, EH40, FH27S, FH32, FH36, FH40
18Higher Strength
AH32, AH36, DH32, DH36 37LTAH27S, LTAH32, LTDH27S, LTDH32,LTEH27S, LTEH32, LTFH27S, LTFH32, LTFH36,LTFH40
18Ferritic Low Temperature
R3S, R4 110Chain Cable StockBarsU1, U2, U3, R3 150
444 Songnae-DongNam-Gu
Pohang Plant No. 1
Tel: +82 54 271 1479 Fax: +82 54 271 1512 Email: mailto:[email protected] Web: http://www.hyundai-steel.comCertificate No. MD00/0819/0013/1 Expiry date: 07/06/2013
Pohang
carbon-manganeseE.A.F. / Con CastSteelmakingHYUNDAI STEEL COMPANY UlsanA, B, D 16Normal StrengthSectionsAH27S, AH32, AH36 16Higher Strength
1857 Jang Heung-DongPohang Plant No. 2
Tel No. +82 54 271 1479 Fax No. +82 54 271 1512Email mailto:[email protected]: www.hyundai-steel.com Certificate No. MD00/3084/0005/1 Expiry date: 07/06/2013
As at 06 November 2012 50Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As BelowB.O.S./E.A.F./Con CastSteelmakingHYUNDAI STEEL COMPANY SeoulNormal strength, Higher Strength 300SlabsSemi-FinishedA, B 22Normal StrengthHot Rolled CoilAH32, AH36 22Higher StrengthA, B 22Normal StrengthPlates from coilsAH32, AH36 22Higher Strength
Songak-MyeonDangjin-Gun
HR Coil PlantKodae-Ri
Tel: +82 41 680 1691 Fax +82 41 680 1699 Email; [email protected] Web: http://www.hyundai-steel.comSlabs as semi finished products nominal 2200mm width x nominal 4400mm length are approved for further processing for rolled products, to the abovemaximum thickness produced by B.O.S Steelmaking and to 210mm maximum thickness produced by E.A.F. Steelmaking.Certificate No. MD00/3446/0003/1 Expiry date: 24/03/2014
Chungnam
A, B, D, E 83Normal StrengthPlatesHYUNDAI STEEL COMPANY SeoulFH32, FH36 40Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
83
360AR, 410AR, 460AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG 83LTDH27S, LTDH32, LTDH36, LTFH27S,LTFH32, LTFH36
40Ferritic Low Temperature
Dangjin Works167-32, Godae-RiTel: +82 41 680 1680 or 1685 Fax +82 41 680 1699 Email; [email protected] or [email protected] Web: http://www.hyundai-steel.comApproval is restricted to plates produced with steel made by the BOF + con cast processing route.Approval for plates in grades AH27S, AH32, AH36, 360AR, 410AR, and 460AR as rolled fine grain Al+V are restricted to the thickness range 20.0mm to35.0mm.Approval for plates in grades AH27S, AH32, AH36, AH40, DH27S, DH32, DH36, DH40, EH27S, EH32, EH36, EH40 for the TM+Acc fine grain Al+Nb+Tisupply condition are restricted to the thickness range >15.0mm to 83.0mm.Approval for plates in grades LTDH27S, LTDH32, LTDH36, LTFH27S, LTFH32, LTFH36 for the TM+Acc fine grain Al+Nb+Ti supply condition are restricted tothe thickness range >15.0mm to 40.0mm.Approval for plates in Normalising Rolled condition are restricted to maximum 3200mm width.Plates with specified through thickness properties may be accepted with the suffix Z35 applied to Higher Strength Grades in the TM+acc Fine Grain Al+Nb+Tisupply condition and TM Fine Grain Al+Nb+Ti supply condition .Certificate Number: MD00/3761/0007/1 Expiry: 25/03/2013
alloy 120MachineryBarsJEENYANG IND. Co., Ltd. Ulsan
Yeongcheon-City,Keongbuk,
446, Bonchon-Dong
Tel: +82 (0)54 335 3500 Fax: +82 (0)54 335 0355 Email: [email protected] Web: www.jysteel.com
Cert No MD00/3897/0001/1 Expiry date: 23/03/2014
As belowE.A.F. / IngotSteelmakingKISCO Changwoncarbon, carbon-manganese, alloy 140IngotsSemi-Finished
N° 70, Shinchon-dongChangwon
Tel +82 55 260 0746 Fax +82 55 282 4123 mail mailto:[email protected] Web page http://www.kisco.co.krIncluding steelmakingCertificate No. MD00/0884/0004/1 Expiry date: 12/01/2015
Kyungnam
A 15Normal StrengthSectionsKOREA STEEL SHAPES CO., LTD Busan PortA 65Normal StrengthBarsAH32 30Higher Strength
1660-1 Songjeong-DongGangseo-Gu
Noksan Works
Tel: +82 51 310 8912 Fax: +82 51 831 3957 Email mailto:[email protected] Web http://www.ekosco.comCertificate No. MD00/3096/0005/1 Expiry date: 08/05/2013
Busan
As belowE.A.F. / Con CastSteelmakingKOREA STEEL SHAPES CO., LTD ChangwonA, AH32, AH36, carbon, carbon-manganese 220BilletsSemi-Finished
68, Gyenae-Ri, Chilseo-MyeonHaman-Gun
Chilseo Works
Tel: +82 55 589 1159 Certificate No. MD00/3097/0001/1 Expiry date: 11/10/2014
Gyeongnam
As at 06 November 2012 51Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
austenitic stainless 85MachineryBarsKWANG JIN IND CO. LTD. Busan Portalloy 93carbon, carbon-manganese 100
307-103 Shinpyeong-dong,Saha-gu,
Tel No: +82 51 204 9101 Fax No. +82 51 204 9109Email: [email protected] Address www.kjsteel.co.krCert No MD00/3758/0001/1 Expiry date 15.03.2013
Busan,604-030
As belowB.O.S. / Con CastSteelmakingPOSCO Gwangyang Works ChangwonNormal strength, Higher Strength 300SlabsSemi-FinishedA, B, D, E 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG
35Boiler & Pressure Vessel
A, B, D 22Normal StrengthHot Rolled CoilAH27S, AH32, AH36, DH27S, DH32, DH36 12Higher Strength360AR, 410AR 12Boiler & Pressure Vessel
700 Kumho-dongKwangyang-si
Tel: +82 61 790 2170 Fax: +82 61 790 2909 Email: mailto:[email protected] Web: http://www.posco.comThe supply of semi-finished products, slabs, nominal 1750mm wide x 6000mm long x 20 tonnes, for supply for further processing for rolled products.Hot rolled coils in normal strength grades in the supply condition thermomechanical fine grain aluminium are restricted to the thickness ranges >12 to 22mm.Certificate Number: MD00/3086/0008/1 Expiry: 14/07/2014
Cheonnam 545-711
As BelowB.O.S./E.A.F./Con CastSteelmakingPOSCO Pohang Works UlsanA, B, D, E 100Normal StrengthPlatesAH46S*, DH46S*, EH46S* 80Higher StrengthFH27S, FH32, FH36 83AH40, DH40, EH40 90AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100
360AR, 410AR 40Boiler & Pressure Vessel460FG, 490FG, 510FG 90360FG, 410FG 100LTAH27S, LTAH32, LTAH36, LTDH27S,LTDH32, LTDH36, LTEH27S, LTEH32, LTEH36,LTFH27S, LTFH32, LTFH36
50Ferritic Low Temperature
304L, 304LN, 316L, 316LN 80Austenitic StainlessUNS S31803, UNS 32900*, UNS 32205* 50Duplex StainlessE 12Normal StrengthHot Rolled CoilA, B, D 22EH27S, EH32, EH36 16Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36 22460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 22304L, 316L 8Austenitic Stainless
5, Dongcheon-DongNam-ku, Pohang City,
Tel: +82 2 3457 1586 Fax: +82 2 3457 1981 Email: mailto:[email protected] Web: http://www.posco.co.kr/posco-inAll plates with specified through thickness properties except AH46S, DH46S and EH46S.*approved applications only.Certificate No. MD00/1206/0015/1 Expiry date: 01/05/2013
Kyungsangbuk-Do
As belowE.A.F. / IngotSteelmakingPOSCO SPECIALITY STEEL CO., LTD. Changwoncarbon, carbon-manganese, alloy, austeniticstainless
150IngotsSemi-Finished
carbon, carbon-manganese, alloy 150StructuralBarsaustenitic stainless 170carbon, carbon-manganese, alloy 150Machinery
ChangwonKyungnam
65, Shinchon-dong
Tel: +82 (0)55 269 6727 Fax: +82 (0)55 269 6907 Email:mailto:[email protected] http://www.poscoss.comCertificate No. MD00/1294/009/1 Expiry date: 09/08/2011
641-370
A 18Normal StrengthPlates from coilsS & STEEL CO., LTD. Busan PortAH27S, AH32 15Higher Strength
As at 06 November 2012 52Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office1620 Dadae-dong, Saha-guBusanTel: +82 51 262 7525 Fax: +82 51 924 7902 Email: [email protected] Web: http://www.sdstl.co.krCertificate No. MD00/3523/0004/1 Expiry date: 25/09/2014
As belowE.A.F. / IngotSteelmakingSPP YULCHON ENERGY CO., LTD. Mokpocarbon, carbon-manganese, alloy 50IngotsSemi-Finished
Block 8, Yulchon Industrial Complex l, Sinseong-riHaeryong-myeon, Suncheon City, Jeollanam-do
Tel: +82 61 760 7100 Fax: +82 61 725 7733 Email: [email protected] Web: http://www.sppycenergy.co.krIngots as semi finished products are approved for further processing for forgings, nominal maximum dimensions 1630/1850mm diameter x 2850mm long, to theabove maximum weight. Certificate Number: MD00/3866/0001/1 Expiry date: 21/02/2015
Zip code: 540856
As belowE.A.F./Ingot/Con CastSteelmakingSeAH BESTEEL CORPORATION Mokpoalloy 109IngotsSemi-Finishedcarbon, carbon-manganese 155carbon, carbon-manganese, alloy 510Bloomscarbon, carbon-manganese 180Billetscarbon, carbon-manganese, alloy 300MachineryBarsR5 140Chain Cable StockR4S, R4S 146R4 155U1, U2, U3, R3, R3S 165
Gunsan CityJeonlabuk-Do
Gunsan Plant1-6, Soryong-Dong
Tel: +82 63 460 8222 Fax: +82 63 460 8099 Email: mailto:[email protected] Web:http://www.egs.seah.co.krApproval for Chain Cable Stock Grades R3, R3S, R4, R4S and R5 is restricted to supply to DAI HAN ANCHOR CHAIN MFG CO. LTD and Grades R3, R3Sand R4 to Pu Sung Metal Co., Ltd.Semi Finished Products - Ingots, Carbon & Carbon-manganese nominal sizes 2100 / 2350mm diameter x 2800mm long, and Alloy nominal sizes 2350 / 2600mmdiameter x 3050mm long, to the above maximum weight approved for further processing for forgings. Semi Finished Products - Blooms to nominal 390mm width x 5400mm length, to above maximum thickness approved for further processing for Forgings andRolled Products. Semi Finished Products - Billets to nominal 180 width x 11500mm length, to above maximum thickness approved for further processing for Rolled ProductsCertificate No. MD00/1749/0012/1 Expiry date: 04/04/2015
As belowB.O.S. / Con CastSteelmakingYK STEEL CORP. Busan PortA 7Normal StrengthSectionsA 32Normal StrengthBars
Saha-Gu604-817
90 Gupyung-Dong
Tel. +82 (0)51 260 2457 Fax +82 (0)51 265 2430 Email:mailto:[email protected] Web: http://www.yksteel.co.krCertificate No. MD00/0650/0007/1 Expiry date: 26/05/2014
Busan
Luxembourg
As belowE.A.F. / Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonA, B 26Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
26Higher Strength
Esch-Belval Mill66 rue de Luxembourg
BELVAL MILLTMB Rolling Plant
Tel: +352 58 2885 Fax: +352 5835 81 Contact: Mr Muller Email: mailto:[email protected] #: MD00/0030/0006/1 Expiry date: 06/11/2012
L4009 Esch sur Alzette
As belowE.A.F./Ingot/Con CastSteelmakingARCELORMITTAL BELVAL ET DIFFERDANGE LyonA, B 40Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
66 rue de LuxembourgL 4009 Esch sur Alzette
Differdange Mill
Tel: +352 58 2028 84 Fax: +352 5835 81 Email: mailto:[email protected] Web http://www.arcelor.comCertificate No. MD00/0032/0006/1 Expiry date: 12/03/2013
As at 06 November 2012 53Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D 30Normal StrengthSectionsARCELORMITTAL RODANGE ET SCHIFFLANGE LyonAH36, DH36 30Higher Strength
2, Rue de L'industrieL-4801 Rodange
Rodange Mill
Tel: +352 5019 2655 Fax: +352 5019 2217 Email: mailto:[email protected] Web http://www.ares.luCertificate No. MD00/2266/0005/1 Expiry date: 18/01/2013
A 40Normal StrengthSectionsTLM (Train Laminé Marchand) LyonA 40Normal StrengthBars
L-4241 Esch Sur AlzetteBoulevard Aloyse Meyer
Tel: +352 57 129 3331 Fax: +352 57 129 2126 Email: mailto:[email protected] No. MD00/2265/0005/1 Expiry date: 17/10/2013
Macedonia
A 35Normal StrengthFabricated SectionsFAKOM A.D. BeogradAH36 40Higher Strength
POB 4391000 SKOPJE
St. Aleksandar Makedonski No.5
Tel No.: +389 317 4023, Fax: +389 317 3564 email: mailto:[email protected] Web http://www.fakom.com.mkCertificate No. MD00/2856/0005/1 Expiry date: 22/11/2013
As belowE.A.F. / Con CastSteelmakingMAKSTIL A.D.- SKOPJE BeogradA, B, D 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36 50Higher Strength360AR, 410AR, 460AR 40Boiler & Pressure Vessel360, 410, 460, 490, 460FG, 490FG, 510FG 50360FG, 410FG 100
XVI Makedonska brigada 18P.O. Box 599
Tel: +389 2 328 7024 Fax: +389 2 3175 982 Email mailto:[email protected] Web http://www.makstil.comSpecified through thickness properties for plates up to 50 mm thicknessCertificate No. MD00/2216/0006/1 Expiry date: 23/05/2013
100-Skopje
Malaysia
A 30Normal StrengthPlatesJI KANG DIMENSI Sdn. Bhd. Kuala Lumpur
26080 KuantanPahang Darul Makmur
Lot 69-71, Kawasan Perindustrian Gebeng
Tel: +609 583 9881 Fax: +609 583 4551 Email: mailto: [email protected]: www.jikangdimensi.comCertificate No. MD00/3022/0004/1 Expiry date: 28/06/2015
As belowE.A.F. / Con CastSteelmakingMEGASTEEL SDN. BHD. Kuala Lumpurcarbon, carbon-manganese 70SlabsSemi-FinishedA, B, D, E 16Normal StrengthHot Rolled CoilAH27S, AH36, DH27S, DH32, DH36, EH27S,EH32, EH36
12Higher Strength
460FG, 490FG, 510FG 12Boiler & Pressure Vessel360FG, 410FG 16
Mukim Tanjung Dua Belas42700 Banting
Lot 2319, Kawasan Perindustrian Olak Lempit
Tel: +60 (0)3 3182 2000 Fax: +60 (0)3 3182 2278 Email mailto:[email protected] Web http://www.lion.com.myCertificate No. MD00/2803/0005/1 Expiry date: 05/06/2013
Selangor Darul Ehsan
As at 06 November 2012 54Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Mexico
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingARCELORMITTAL LAZARO CARDENAS, S.A. deC.V.
Metepec/Veracruz
carbon, carbon-manganese 250SlabsSemi-Finished
60950- Lázaro CárdenasMichoacan
Av Francisco J. Mujica N° 1-B
Steel types carbon and carbon-manganese cover the supply of blooms for processing into normal strength, high strength and ferritic steels for low temperatureservice according to the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible forordering steel which complies with their approved chemical composition and enables them to achieve the required mechanical properties
Tel: +52 753 533 1871 Fax: +52 753 533 1187 Email:[email protected] Web http://www.arcelormittalsteel.comCertificate No. MD00/0783/0006/1 Expiry date: 09/01/2014
Netherlands
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingNEDSTAAL B.V. RotterdamMarine
carbon, carbon-manganese, alloy 11IngotsSemi-Finished
carbon, carbon-manganese, alloy 320Slabs
carbon, carbon-manganese, alloy 400Blooms
carbon, carbon-manganese, alloy 125Billets
Rapenburg 1P.O. Box 210
Tel: +33 (0)78 692 3715 Fax: +31 (0)78 692 3712 Email mailto:[email protected] Web http://www.nedstaal.nlCertificate No. MD00/3010/0003/1 Expiry date: 12/09/2012
2950 AE Alblasserdam
As belowB.O.S. / Con CastSteelmakingTATA STEEL IJMUIDEN B.V Amsterdamcarbon, carbon-manganese 225SlabsSemi-FinishedA, B 20Normal StrengthPlatesA, B 20Normal StrengthHot Rolled Coil
Postbus 100001970 CA IJmuiden
IJmuiden Works
Tel +31 2514 92110 Fax +31 2514 70414 Email: [email protected]: www.tatasteel.nlCertificate No. MD00/0698/0008/1 Expiry date: 29/09/2015
Norway
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingCELSA ARMERINGSSTÅL AS OsloA, carbon, carbon-manganese 160BilletsSemi-Finished
PO Box 500N-8601 Mo i Rana
Mo Industripark
Tel: +47 7513 6500 Fax: +47 7513 6845 Email: mailto:[email protected] Web http://www.celsanordic.comCertificate No. MD00/2103/0005/1 Expiry date: 07/09/2014
As at 06 November 2012 55Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Peru
As belowB.O.S. / IngotSteelmakingEMPRESA SIDERURGICA DEL PERU S.A.A. CallaoAs belowE.A.F. / IngotA 32Normal StrengthPlatesA 10Normal StrengthHot Rolled Coil
ChimboteAv. Santiago Antunez de Mayolo s/n
Tel +51 43 883000 Fax +51 43 324580 Email: mailto:[email protected] Web: http://www.sider.com.peCertificate No. MD00/0461/0005/1 Expiry date: 11/04/2012
Poland
A, B, D, E 25Normal StrengthPlates''HUTA POKÓJ'' S.A. Katowice360AR, 410AR, 360, 410, 360FG, 410FG 25Boiler & Pressure VesselA, B, D, E 25Normal StrengthSections
ul. Niedurnego 7941-709 Ruda SlaskaTel +48 32 772 1523 Fax +48 32 772 4856 Email: [email protected] Web: http://www.hutapokoj.com.plCertificate No. MD00/0723/0007/1 Expiry date: 10/12/2012
A, B, D, E 40Normal StrengthSections''INTERSPEED'' KatowiceAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S
40Higher Strength
Aleja Solidarnosci 127-400 Ostrowiec Swietokrzyski
PRZEDSIEBIORSTWO HANDLOWO USLUGOWOPRODUKCYJNE Sp z.o.o
Tel: +48 (0)41 266 0700; +48 695 385 015 Fax: +48 (0)41 266 0701 Email: mailto:[email protected] Web page http://www.interspeed.com.plCertificate No. MD00/2007/0006/1 Expiry date: 25/07/2014
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 220SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilAH27S, AH32 16Higher StrengthA, B, D 15Normal StrengthPlates from coilsAH27S, AH32 16Higher Strength410 FG, 360 FG, 460 FG 16Boiler and Pressure Vessel
30-969 Kraków
ODDZIAL W KRAKOWIEul. Ujastek 1
Tel: +48 12 293 2104 Fax: +48 12 293 2145 email: [email protected] Web: http://www.arcelormittal.com/poland/Slabs as semi finished products are approved for further processing for rolled products to the maximum thickness shown above and nominal 1580mm widthand 11000mm length.Coils and plates are approved to maximum 2100mm width.Certificate #: MD00/0707/0010/1 Expiry date: 27/01/2014
carbon, carbon-manganese, alloyB.O.S. / Con CastSteelmakingARCELORMITTAL POLAND S.A. Katowicecarbon, carbon-manganese 300SlabsSemi-Finishedcarbon, carbon-manganese, Alloy 280Blooms/BilletsB, D, E 15Normal StrengthSectionsA 20
41-308 Dabrowa Gornicza
Oddzial w Dabrowie GorniczejAl. J. Pilsudskiego 92
Tel: +48 32 776 87 14 Fax: +48 32 776 84 86 Email [email protected] Web: http://www.arcelormitta.com/poland/Approved for ingots, and continuously cast products for re- rolling in all the normal and higher tensile strength grades.Certificate No. MD00/0717/0010/1 Expiry date: 06/02/2015
As belowE.A.F./Ingot/Con CastSteelmakingARCELORMITTAL WARSZAWA Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 25IngotsSemi-Finishedcarbon, carbon-manganese, alloy 220Blooms/Billetscarbon, carbon-manganese, alloy 65StructuralBarscarbon, carbon-manganese, alloy 65Machinery
ul. Kasprowicza 13201-949 WarszawaTel: +48 22 835 8081 Fax: +48 22 835 8638Email: mailto:[email protected] Web: http://www.arcelormittal-warszawa.comCertificate No. MD00/0720/0007/1 Expiry date: 02/08/2015
As belowE.A.F. / IngotSteelmakingCELSA "HUTA OSTROWIEC" Sp. z o.o. Katowicecarbon, carbon-manganese, alloy 130IngotsSemi-Finished
As at 06 November 2012 56Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
ul. Samsonowicza 227-400 Ostrowiec Swietokrzyski
ZAKLAD WYROBOW KUTYCH
Tel: +48 (0)41 2492390 Fax: +48 (0)41 2493779 EMail:[email protected] Web page http://www.celsaho.comCertificate No. MD00/2006/0006/1 Expiry date: 26/10/2013Ingots size maximum 130 MT 2.33 m diameter
As belowE.A.F. / Con CastSteelmakingCELSA "HUTA OSTROWIEC" Sp. z o.o. Katowicecarbon, carbon-manganese, alloy 160BilletsSemi-Finished
ZAKLAD WYROBOW WALCOWANYCHTel: +48 (0) 41 2493269 Fax: +48 (0)41 2492037EMail :[email protected] Web page:www.celsaho.comCertificate #: MD00/3444/0002/1 Expiry date: 26/10/2013
As belowE.A.F. / Con CastSteelmakingCMC ZAWIERCIE S.A. Katowicecarbon, carbon manganese 160Blooms/BilletsSemi-Finished
ul. Pilsudskiego 8242-400 ZawiercieTel: +48 32 672 57 55 Fax: +48 32 672 57 59 Email: [email protected] Web: www.cmcpoland.comCertificate No. MD00/3594/0003/1 Expiry date: 06/05/2015
Includes billets/blooms up to 185 x 160mm.
As belowE.A.F. / Con CastSteelmakingFERROSTAL LABEDY Sp. z o.o. Katowicecarbon, carbon-manganese, alloy 160BilletsSemi-Finishedcarbon, carbon-manganese, alloy 170Bars
ul. Zawadzkiego 4744-109 GliwiceTel: +48 32 234 7600 Fax: +48 32 234 7650 EMail mailto:[email protected] Web page http://www.ferrostal.com.plThe semi finished products above are approved for use for further processing for the finished products defined above.Certificate No. MD00/2307/0005/1 Expiry date: 31/03/2014
carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingGONAR-BIS Sp. z.o.o. Katowice
40-851 Katowice
Wydzial Stalownia Baildonul . Zelazna 5
Tel: +48 32 359 7860/0810 Fax: +48 32 359 7092 Email: [email protected] Web: www.stalownia.gonar.com.plCertificate No. MD00/3580/0001/1 Expiry date: 06/04/2012
As belowE.A.F./Ingot/Con CastSteelmakingHSW - HUTA STALI JAKOSCIOWYCH SA Katowicecarbon, carbon-manganese, alloy 15IngotsSemi-FinishedCarbon, Carbon-Manganese, Alloy 130Rolled Billetscarbon, carbon manganese, Alloy 270Blooms/BilletsCarbon, Carbon manganese, Alloy 120Rolled BarsA, B, D, E 120Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
120Higher Strength
carbon, carbon-manganese, alloy 120Structuralcarbon, carbon-manganese, alloy 120MachineryU1, U2, U3 110Chain Cable Stock
ul. Kwiatkowskiego 137-450 Stalowa WolaTel: +48 15 813 53 20 Fax: +48 15 872 21 55 Email: mailto:[email protected] Web: http://www.hsw-hsj.com.plCertificate No. MD00/2406/0006/1 Expiry date: 23/05/2014
A, B 20Normal StrengthSectionsHUTA BANKOWA Sp. z o.o. KatowiceAH27S, AH32, AH36, DH27S, DH32, DH36 20Higher StrengthA 250Normal StrengthBarscarbon, carbon-manganese 250Structuralcarbon, carbon-manganese, alloy 250MachineryU1, U2 160Chain Cable Stock
ul. Sobieskiego 2441-300 Dabrowa GórniczaTel +48 32 295 7430 Fax +48 32 262 3788 Email: [email protected]; [email protected] Web http://www.hutabankowa.com.plCertificate No. MD00/0716/0007/1 Expiry date: 05/03/2013
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingHUTA BATORY Sp. z o.o. Katowice
carbon, carbon-manganese, alloy, austeniticstainless
14IngotsSemi-Finished
ul.Dyrekcyjna 641-506 ChorzówTel: +48 32 77 22 155 Fax:+48 32 77 22 400 Email:mailto:[email protected] Web: http://www.hutabatory.com.plCertificate No. MD00/0711/0009/1 Expiry date: 07/10/2013
A, B, D, E 100Normal StrengthPlatesHW PIETRZAK HOLDING Sp. z o.o. KatowiceAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100A/304L 50Clad
As at 06 November 2012 57Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
41-506 Chorzów
Oddzial Walcownia Blach Batory w Chorzowieul. Lesna 42
Tel: +48 32 728 981 616 Fax: +48 32 77 22 117 Email mailto:[email protected] http://www.pietrzak-holding.plAll plates with specified through thickness propertiesCertificate No. MD00/2766/0006/1 Expiry date: 18/10/2013
As belowE.A.F. / Con CastSteelmakingISD HUTA CZESTOCHOWA Sp. z o.o. Katowicecarbon, carbon-manganese 250SlabsSemi-Finishedcarbon, carbon-manganese 280BloomsA, B, D, E 50Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR, 460AR, 360FG, 410FG, 460FG,490FG, 510FG
50Boiler & Pressure Vessel
42-207 Czestochowaul. Kucelinska 22
Tel: +48 34 323 8147 Fax: +48 34 323 0034 Email: maito:[email protected] Web: http://www.isd- hcz.com.plCertificate No. MD00/0713/0010/1 Expiry date: 06/04/2015
carbon, carbon-manganese, alloy 150StructuralBarsWALCOWNIE BRUZDOWE "BATORY" Sp. z.o.o. Katowicecarbon, carbon-manganese, alloy 150Machinery
41-500 Chorzówul. Zelazna 22
Tel: +48 32 772 2698 Fax: +48 32 772 2250 Email:[email protected] Web:http://www.wbb.net.plCertificate No. MD00/3545/0002/1 Expiry date: 01/12/2014
Romania
As belowB.O.S./Ingot/Con CastSteelmakingARCELORMITTAL GALATI S.A. GalatzA, B, D, E 100Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
100Higher Strength
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 100
800698 GalatiSos Smardan Nr.1
Tel: +40 236 802100 Fax: +40 236 802101 Email: mailto:[email protected] Web page http://www.arcelormittal.comApproval includes for plates with specified through thickness properties, designation Z25, in all grades up to 60 mm thickness in the normalized condition.Certificate No. MD00/0333/0007/1 Expiry date: 04/12/2013
carbon, carbon-manganese, alloy 250E.A.F. / IngotSteelmakingDOOSAN IMGB S.A Galatzcarbon, carbon-manganese, alloy 250IngotsSemi-Finished
Berceni Road Nr. 104Sector 4
Tel: +40 21 301 2549 Fax: +40 21 301 2502 Email: mailto:[email protected]
Certificate No. MD00/1259/0001/1 Expiry date: 10/09/2014
041919 Bucharest
As belowE.A.F. / Con CastSteelmakingMECHEL TARGOVISTE S.A. Galatzcarbon, carbon manganese, Alloy 150Blooms/BilletsSemi-FinishedU1, U2, U3 95Chain Cable StockBars
Sos. Gaiesti, 9-11Jud Dambovita, 130087
Targoviste
Tel: +40 245 632907 Fax: +40 245 213322 Email: mailto:[email protected] Web: http://www.mechel.comCertificate No. MD00/2293/0005/1 Expiry date: 14/02/2014
carbon, carbon-manganese 120E.A.F. / IngotSteelmakingS.C. FORTUS S.A. GalatzBd. Poitiers Nr. 10700671 IASITel: +40 232 222023 Fax: +40 232 220370 Email: mailto: [email protected] Web: http://www.fortus-iasi.roCertificate No. MD00/1258/0003/1 Expiry date: 12/04/2014
A 50Normal StrengthSectionsS.C. LAMINORUL S.A. - BRAILA GalatzAH27S, AH32, AH36 12Higher StrengthA 50Normal StrengthBars
810461 BrailaSos. Industria Sarmei nr. 2
Tel +40 239 68 5597 Fax +40 239 66 9387 Email: mailto:[email protected] Web http://www.laminorul.roCertificate No. MD00/1916/0007/1 Expiry date: 30/03/2015
As at 06 November 2012 58Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingS.C. SILCOTUB S.A. Galatzcarbon, carbon-manganese, alloy 260Blooms/BilletsSemi-Finished
Prelungirea Bucurestiului Str. No.162910125
TENARIS GROUPSteel Shop Calarasi
Tel +40 242306 600 Fax No.Web Address www.tenaris.comCertificate No. MD00/3997/0001/1 Expiry date: 27/02/2015
Calarasi
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingSC DUCTIL STEEL SA Galatzcarbon, carbon-manganese 100BilletsSemi-Finished
str. Mihai Eminescu, No 10,cod 325700,loc Otelu Rosu
Punct de lucru Otelu-Rosu
Tel No: +40 (0)255 532 239 Fax: +40 (0) 255 532 054Email: [email protected] www.ductilsteel.roCertificate No: MD00/ 3888/ 0001/ 1 Expiry Date 10/03/2014
jud.Caras Severin
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingSC TMK-RESITA S.A. Galatzcarbon, carbon-manganese, alloy 177BilletsSemi-Finished
Traian Lalescu No. 36Caras-SeverinTel: +40 (0)255 217211 Fax: +40 (0)255 211883 Email: mailto: office.resita.tmk-artrom.roWeb http://www.tmk-artrom.roCertificate No. MD00/3804/0001/1 Expiry date: 08/07/2013
Russia
A, B, D 14Normal StrengthSections"RM - rolling complex" St. PetersburgAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36
14Higher Strength
11, Sedova street192019, St Petersburg
St. Petersburg branch "RM - steel" Ltd.
Tel: +7 812 318 0015 Fax: +7 812 568 0015 Email: mailto:[email protected] Web http//www.rm-steel.comCertificate No. MD00/1910/0008/1 Expiry date: 16/01/2014
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingCHELYABINSK METALLURGICAL PLANT OAO St. Petersburgcarbon, carbon-manganese, alloy 20IngotsSemi-Finished
2-d Paveletskaya ul, 14454047- Chelyabinsk
Tel; +7 351 725 30 24 Fax: +7 351 722 86 29 Email mailto:[email protected] supllied as semi finished products are for further processing for forgings.Certificate No. MD00/3262/0004/1 Expiry date: 11/08/2015
A, B, D, E 40Normal StrengthPlatesJ.S.C. SEVERSTAL St. PetersburgEH27S, EH32 32Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH40
40
360, 410 32Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 40
30 Mira Str162 699 Cherepovets
Rolling Mill 2800
Tel: +7 8202 531146 Fax: +7 8202 53 2424 EMail: mailto:[email protected] Web http://www.severstal.ruPlates in the As Rolled, Normalized, Quenched and Tempered conditions with specified through thickness properties.Plates in the Normalizing rolled condition to 2200mm maximum width.Certificate #: MD00/0298/00076/1 Expiry date : 14/06/2013
Vologoda Region
A 15Normal StrengthPlatesJ.S.C. SEVERSTAL St. PetersburgA, B, D, E 12Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
12Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 12Boiler & Pressure Vessel
162699 CherepovetsRolling Mill 2000
Tel: +7 8202 53 1146 Fax: +7 8202 53 2424 EMail: mailto:[email protected] Web http://www.severstal.ruCertificate No. MD00/2801/0006/1 Expiry date: 14/06/2013
D, E 50Normal StrengthPlatesJ.S.C. SEVERSTAL St. PetersburgA, B 70AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
70Higher Strength
As at 06 November 2012 59Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Saint Petersburg
Rolling Mill 5000Kolpino
Tel: +7 8202 561146 Fax: +7 8202 53 2424 EMail: mailto:[email protected] Web http://severstal.ruPlates with specified through thickness propertiesCertificate #: MD00/2802/0005/1 Expiry date: 14/06/2013
As belowB.O.S. / Con CastSteelmakingJ.S.C. SEVERSTAL St. PetersburgAs belowE.A.F. / Con Castcarbon, carbon-manganese 315SlabsSemi-Finished
B.O.S and E.A.F WorkshopsTel: +7 8202 561146 Fax: +7 8202 53 2424 EMail: mailto:[email protected] Web http://severstal.ruCertificate #: MD00/3821/0001/1 Expiry date: 14/06/2013
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingJOINT STOCK COMPANY«EVRAZ NIZHNY TAGIL St. PetersburgNormal strength, Higher Strength 300SlabsSemi-Finished
1, Metallurgov Str.,Nizhny Tagil,
METALLURGICAL PLANT»
Tel:+007 3435 490611 Fax:+007 3435 496169 Email:mailto:[email protected] Web http://www.ntmk.ruCertificate No. MD00/2660/0006/1 Expiry date: 05/04/2015
Sverdlovsk Region, 622025
carbon, carbon-manganese, alloyE.A.F. / Con CastSteelmakingJSC AMURMETAL St. Petersburgcarbon, carbon-manganese, alloy 200SlabsSemi-Finishedcarbon, carbon-manganese, alloy 125Billets
30, Vagonnaya Str681000 Komsomolsk-on-AmureTel No. 007 4217 52 9333 Fax No. 007 4217 52 9333Email: [email protected]: www.amurmetal.ruCertificate No. MD00/3588/0002/1 Expiry: 10/03/2015
As below 250B.O.S. / Con CastSteelmakingJSC EVRAZ CONSOLIDATED St. PetersburgA, B, D, E, AH32, AH36, DH32, DH36, EH32,EH36
250SlabsSemi-Finished
654043 Kosmicheskoye shosse,16, Novokuznetsk
WEST SIBERIAN METALLURGICAL PLANT
Tel No. 007 3843 59 5900 Fax 007 3843 59 4343Email [email protected] address xxxxxxxxxxxxxxxCertificate No. MD00/3723/0002/1 Expiry Date 21/12/2012
As belowO H / IngotSteelmakingJSC KIROVSKIY ZAVOD St. Petersburgcarbon, carbon-manganese 120Semi-finished ProductsBars
47 Stachek Prospect198097 St. Petersburg
Petrostal Steel Works
Tel: +7 812 783 6813 Fax: +7 812 783 6504 Email mailto:[email protected] Web: http://www.petrostal.spb.ruCertificate No. MD00/1751/0006/1 Expiry: 30/01/2015
As belowB.O.S. / Con CastSteelmakingOJSC "Magnitogorsk Iron & Steel Works" St. Petersburgcarbon, carbon-manganese 250SlabsSemi-Finished
93, Kirova Street455002 Magnitogorsk
Steel Making and Central Laboratory
Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruApproval covers for slabs as detailed above to nominal width 2520mm and nominal length 7000mm for further processing for rolled products.Certificate No. MD00/3103/0003/1 Expiry date: 27/08/2013
A 10Normal StrengthHot Rolled CoilOJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel
Rolling Mill 2000Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruCertificate No. MD00/3834/0001/1 Expiry date: 27/08/2013
A 25Normal StrengthPlatesOJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 25Boiler & Pressure Vessel
Rolling Mill 2350Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruCertificate No. MD00/3835/0001/1 Expiry date: 27/08/2013
A 10Normal StrengthHot Rolled CoilOJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 10Boiler & Pressure Vessel
Rolling Mill 2500Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruCertificate No. MD00/3836/0001/1 Expiry date: 27/08/2013
As at 06 November 2012 60Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A 50Normal StrengthPlatesOJSC "Magnitogorsk Iron & Steel Works" St. Petersburg360AR, 410AR 40Boiler & Pressure Vessel
Rolling Mill 4500Tel +7 351 924 7929 Fax +7 351 924 9290 Emial: [email protected] Web http://www.mmk.ruApproval covers for plates in the thickness range 30.0 to 50.0mm, to the maximum thickness shown above.Certificate No. MD00/3837/0001/1 Expiry date: 27/08/2013
As belowB.O.S. / Con CastSteelmakingOJSK Novolipetsk Iron & Steel Corporation MoscowAs below 260SlabsSemi-FinishedA, B, D 16Normal StrengthHot Rolled CoilAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH36, EH40
12Higher Strength
460FG, 490FG 10Boiler & Pressure Vessel360, 410, 360FG, 410FG 16
Pl. Metallurgov 2, NLMKLipetsk
398040, Russia
Tel: +7 0742 444688 Fax: +7 0742 432541 Email:mailto:[email protected] Web:http://www.nlmk.ru Telex: 412630NLMK RUCertificate No. MD00/1124/0005/1 Expiry date: 06/11/2013
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingOSKOL St. Petersburgcarbon, carbon-manganese 360BloomsSemi-FinishedU1, U2, U3 80Chain Cable StockBars
Belgorod Region
ELECTROMETALLURGICAL KOMBINAT309515 Stary Oskol-15
Tel +07 4725 375364 Fax +07 4725 373755 [email protected] Web http://www.oemk.ruCertificate No. MD00/3065/0004/1 Expiry date: 26/02/2013
As belowO H / IngotSteelmakingURAL STEEL Open Joint-Stock Company St. PetersburgAs belowE.A.F./Ingot/Con CastB, D 40Normal StrengthPlatesA 50AH32, AH36 40Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 40Boiler & Pressure Vessel
NovotroitiskOrenburg Region
1, Zavodskaya Street
Tel: +7 3537 66 20 66 Fax: +7 3537 66 25 27 Email: mailto:[email protected] Web: http://www.uralsteel.comCertificate No. MD00/2337/0007/1 Expiry date: 25/05/2014
462353
Serbia
As belowB.O.S. / Con CastSteelmakingU.S. STEEL SERBIA d.o.o. BeogradAs below 200SlabsSemi-FinishedA, B, D 15Normal StrengthHot Rolled CoilA, B, D 15Normal StrengthPlates from coils
Radinac11300 SmederevoTel: +381 26 224 429 Fax: +381 26 225 069 email: mailto:[email protected] No. MD00/0360/0005/1 Expiry date: 17/03/2013
Slovak Republic
A, B, D, E, AH32, AH36, DH32, DH36, EH32,EH36
B.O.S. / Con CastSteelmakingU.S. STEEL KOSICE, s.r.o. Prague
carbon, carbon-manganese 220IngotsSemi-FinishedA, B 12Normal StrengthPlates360AR, 410AR 12Boiler & Pressure VesselA, B, D 12Normal StrengthHot Rolled Coil360, 410, 360FG, 410FG 12Boiler & Pressure Vessel
Vstupny areal U.S. Steel044 54 KosiceTel: +421 55 673 4731 Fax: +421 55 675 4731 Email: mailto:[email protected] Web: http:www.usske.skCertificate No. MD00/1649/0006/1 Expiry date: 18/06/2014
Semi-finished products in carbon and carbon-manganese steels in all normal strength grades and higher tensile strength grades up to EH36 with maximumdimensions 1540mm wide to 12000mm long and thickness as stated.
As at 06 November 2012 61Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowB.O.S. / Con CastSteelmakingZELEZIARNE PODBREZOVA A.S. Praguecarbon, carbon manganese 280Blooms/BilletsSemi-Finished
Kolkáreñ 35976 81 PodbrezovaTel: +421 48 645 4040 Fax: +421 48 645 4041 Email: mailto:[email protected] Web: http://www.zelpo.skIncluding eddy current testing in lieu of hydraulic testing.Certificate No. MD00/1464/0003/1 Expiry date: 05/12/2013
Slovenia
carbon, carbon-manganeseE.A.F. / Con CastSteelmakingACRONI, d.o.o. Zagrebaustenitic stainlessB.O.S/V.O.D./Con Castcarbon, carbon-manganese, austenitic stainless 250SlabsSemi-FinishedA, B, D, E 40Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
360AR, 410AR, 360, 410, 360FG, 410FG, 460FG,490FG, 510FG
40Boiler & Pressure Vessel
304L, 316L, 317L, 321, 347 70Austenitic Stainless
Cesta Borisa Kidrica 44SI - 4270 Jesenice
Member of Slovenian Steel Group
Tel: +385 4 584 1040 Fax: +385 4 584 1068 Email: mailto:[email protected] Web: http://www.acroni.si Certificate No. MD00/1391/0007/1 Expiry date: 26/10/2013
carbon, carbon-manganese, austenitic stainlessE.A.F. / IngotSteelmakingMETAL RAVNE d.o.o. ZagrebA, B 20Normal StrengthSectionsA, B 120Normal StrengthBars
2390 Ravne na KoroškemKoroška cesta 14
Tel: +386 2 870 7200 Fax: +386 2 870 7219 Email: mailto:[email protected] Web: http://www.metalravne.comCertificate No. MD00/2889/0004/1 Expiry date: 01/06/2014
South Africa
As BelowB.O.S./E.A.F./Con CastSteelmakingARCELORMITTAL SOUTH AFRICA LTD. JohannesburgAs below 240SlabsSemi-FinishedB, D, E 30Normal StrengthPlatesA 50AH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36
30Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 30Boiler & Pressure Vessel360AR, 410AR 40LTAH32, LTAH36, LTDH32, LTDH36, LTEH32,LTEH36, LTFH32, LTFH36
30Ferritic Low Temperature
Delfos BoulevardVanderbijlpark, 1911
Vanderbijlpark Steel
Tel +27 (0)16 889 2657 Fax +27 (0)16 889 5019 Email: mailto:[email protected] Web:http://www.arcelormittal.comCertificate No. MD00/1404/0008/1 Expiry date: 08/05/2014
PO Box 2, Vanderbijlpark 1900
As belowB.O.S. / Con CastSteelmakingEVRAZ HIGHVELD STEEL & VANADIUM, DurbanA 50Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
40Higher Strength
360AR, 410AR, 360FG, 410FG, 460FG, 490FG,510FG
40Boiler & Pressure Vessel
A 12Normal StrengthHot Rolled Coil360, 410 12Boiler & Pressure VesselA, B 50Normal StrengthSectionsA, B 50Normal StrengthBars
Witbank1035
P.O. Box 111
Tel. +27 (0)13 690 9911/9623 Fax. +27 (0)13 690 9559EMail mailto:[email protected] http://www.highveld.co.za Certificate No. MD00/0672/0005/1 Expiry date: 04/07/2013
Mpumalanga
As at 06 November 2012 62Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Spain
As belowE.A.F. / IngotSteelmakingACERALAVA S.A. Bilbaocarbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*
470BloomsSemi-Finished
carbon, carbon-manganese, alloy, austeniticstainless, duplex Stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*
470Billets
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, Ferritic StainlessSteel*, Martensitic Stainless Steel*
470Bars
carbon, carbon-manganese, alloy, austeniticstainless, duplex stainless, ferritic stainless*,martensitic stainless*
470StructuralBars
01470 AmurrioAlava
Poligono Industrial De Saratxo
Tel: +34 945 891461 Fax: +34 945 393001 email: [email protected]* accepted for approved applications.Approval also includes ingots up to 5 tonne.Certificate No. MD00/0054/0005/1 Expiry date: 21/01/2013
As belowE.A.F. / Con CastSteelmakingACERINOX EUROPA S.A.U. Cadiz304L, 316L, 321, 347 50Austenitic StainlessPlates304L, 316L, 321, 347 20Austenitic StainlessCoil
11379 Los BarriosCadiz
Palmones
Tel: +34 956 629300 Fax: +34 956 629311Certificate No. MD00/0057/0007/1 Expiry date: 16/12/2013
austenitic stainlessE.A.F. / Con CastSteelmakingACEROS INOXIDABLES OLARRA S.A. Bilbao304L, 316L, 321 100Austenitic StainlessBars
Larrabarria 148150 Larrondo-Loiu
Tel: +34 617 464 872 Fax: +34 944 531 392email: [email protected] web: www.olarra.comCertificate No. MD00/1753/0005/1 Expiry date: 09/09/2012
Vizcaya
carbon, carbon-manganeseB.O.S. / Con CastSteelmakingARCELOR MITTAL ESPAÑA Gijoncarbon, carbon-manganese 235SlabsSemi-Finished
Apartado 9033402 Avilés
Factoría de Avilés
Tel: +34 985 187299 Email: mailto:[email protected] page http://www.arcelormittal.comCertificate #: MD00/0460/0006/1 Expiry date: 31/08/2014
Asturias
A, B, D, E 80Normal StrengthPlatesARCELOR MITTAL ESPAÑA GijonDH40, EH40, FH27S, FH32, FH36, FH40 25Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
80
360FG, 410FG, 460FG, 490FG, 510FG 80Boiler & Pressure Vessel
Apartado 57033200 Gijón
Factoriá de Gijón
Specified through thickness properties for plates up to 50mm thickness.Tel: +34 985 187299 Fax +34 985 187 519Email: mailto:[email protected] Web page http://www.arcelormittal.comCertificate No. MD00/1804/0008/1 Expiry date: 25/09/2014
As belowE.A.F. / Con CastSteelmakingCOMPAÑÍA ESPAÑOLA DE LAMINACIÓN, S.L. BarcelonaA 180BilletsSemi-FinishedA 50Normal StrengthSectionsA 35Normal StrengthBars
08755Castellbisbal (Barcelona)
Poligono Industrial 'San Vicente' s/n
Tel: +34 630 970 990 Fax: +34 93 773 0552 Email:mailto:[email protected] Web:http://www.celsa.comApproved for the supply of continuously cast billets up to 180 x 180 mm.Certificate No. MD00/0343/0007/1 Expiry date: 22/03/2013
Steel types carbon and carbon-manganese cover the supply of billets for processing into normal strength steels according to the Society's Rules for theManufacture, Testing and Certification of Materials, Chapter 3. The final processing mill is responsible for ordering steel which complies with their approvedchemical composition and enables them to achieve the required mechanical properties
As at 06 November 2012 63Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As belowE.A.F. / Con CastSteelmakingGERDAU ACEROS ESPECIALES EUROPA S.L.(GERDAU)
Bilbao
As below 300BloomsSemi-Finished
carbon, carbon-manganese, alloy 100MachineryBars
R3, R3S, R4, API-2F, R5 78Chain Cable Stock
U2, U3 100
Bo. Ugarte, S/NP.O. Box 76
Planta Basauri
Tel +34 944 871 726 Fax +34 944 871826 Email: mailto:[email protected]: www.gerdau.esThe approval for bars for chain cable stock grades R3 and R3S are restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R3-R3S.The approval for bars for chain cable stock grade R4 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R4.The approval for bars for chain cable stock grade R5 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R5.The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.Certificate No. MD00/0051/0008/1 Expiry date: 22/01/2015
48970 Basauri (Vizcaya)
carbon, carbon-manganese, alloy 37StructuralBarsGERDAU ACEROS ESPECIALES EUROPA S.L.(GERDAU)
Bilbao
carbon, carbon-manganese, alloy 37Machinery
C/Portal De Gamarra, No. 2201013 Vitoria (Alava)
Planta Vitoria
Tel: +34 94 516 4638 Fax: +34 94 516 4748 Email: mailto:[email protected] Web://www.gerdau.esCertificate Number: MD00/2076/0006/1 Expiry: 31/01/2015
As belowE.A.F. / IngotSteelmakingGERDAU SIDENOR FABRICA DE REINOSA BilbaoA 220Normal StrengthBarscarbon, carbon-manganese, alloy 220MachineryR3, R3S, R4, API-2F, R5 185Chain Cable Stock
Paseo Alejandro Calonje, 139200 Reinosa (Cantabria)Tel: +34 942 775 187 Fax: +34 942 775 283 Email: mailto:[email protected] Web http://www.sidenor.comThe approval for bars for chain cable stock grades R3 and R3S are restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R3-R3S.The approval for bars for chain cable stock grades R4 and R5* are restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R4S.The approval for bars for chain cable stock in Grade R4 to 130mm diameter manufactured by con cast steelmaking at Fabrica de Basauri, rolling at AzkoitaPlant, finishing at Reinosa are restricted for supply to Vicinay Cadenas S.A. to purchasing specification MP-R4S. The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.Certificate No. MD00/0546/0010/1 Expiry date: 20/06/2014
A, B, D, E 25Normal StrengthFabricated SectionsHIERROS MARCELINO FRANCO S.A. GijonAH32, AH36, DH32, DH36, EH32, EH36 25Higher Strength
Avda. Conde Guadalhorce, 13133400 Avilés
Industrias Metálicas de Cancienes S.L. "INMECA"
Tel: +34 985 56 60 67 Fax: +34 985 566 653 EMail mailto:[email protected] No. MD00/2778/0004/1 Expiry date: 30/01/2013
Asturias
A 25Normal StrengthSectionsLAMINADOS LOSAL, S.A. BilbaoAH32, AH36, DH32, DH36, EH32, EH36, FH32,FH36
11Higher Strength
Bekoibarra, 9P.O. Box 17
Tel: +34 946251400 Fax: +34 946254976 Email: [email protected] Web www.losal.esCertificate No. MD00/0993/0006/1 Expiry date: 19/01/2014
48300 - Gernika
A 25Normal StrengthSectionsRUGUI S.L. San SebastianDH32, DH36 14Higher Strength
Poligono Industrial Basarte20720 Azcoitia (Guipuzcoa)
Tel: +34 943 857311 Fax: +34 943 857312 Email: mailto:[email protected] Web http://www.rugui.comThe approved sections are in the form of flat bars up to a width of 150mm. Certificate No. MD00/1915/0005/1 Expiry date: 06/02/2014
Apdo. de Correos no. 8 Azpeitia (Guipuzcoa)
As at 06 November 2012 64Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese, alloy 200MachineryBarsSIDENOR INDUSTRIAL S.L. (Gerdau Sidenor) San SebastianR4 117Chain Cable StockR3, R3S 123R5 150U1, U2, U3 152
Ctra. de Zumárraga, s/n20720 Azcoitia
Tel: +34 943 025206 Fax: +34 943 025299 Email: mailto:[email protected] The approval for bars for chain cable stock grades R3 and R3S are restricted to supply to Vicinay Cadenas S.A. to purchasing specification CC-R3-R3S.The approval for bars for chain cable stock grade R4 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R4.The approval for bars for chain cable stock grade R5 is restricted to supply to Vicinay Cadenas S.A. to purchasing specification MP-R5, this approval is withbars rolled from steel made at Sidenor Industrial S.L. Fabrica de Basauri plant. The latest issue of the Vicinay purchasing specifications are accepted subject to these maintaining the required material conditions under which approval wasgranted.
Raw materials ingot and bloom are sourced from Basauri and Reinosa Plants and no longer produce steel.Web:http//:www:gerdau.esCertificate No. MD00/0620/0009/1 Expiry date: 27/03/2014
Guipúzcoa
Sweden
austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingAB SANDVIK MATERIALS TECHNOLOGY Stockholmaustenitic stainless, duplex stainlessE.A.F. / Ingotaustenitic stainless, duplex stainless 6IngotsSemi-Finishedaustenitic stainless, duplex stainless 265Bloomsaustenitic stainless, duplex Stainless 150Billetsaustenitic stainless, duplex stainless 195austenitic stainless, duplex stainless 185Barsaustenitic stainless, duplex stainless 185StructuralBarsaustenitic stainless, duplex stainless 185Machinery
SE-811 81 SandvikenTel: +46 (0) 26 26 3792 Fax: +46 (0) 26 26 3785 Email: mailto:[email protected] Web http://www.smt.sandvik.comCertificate No. MD00/2173/0005/1 Expiry date: 31/10/2012
Semi Finished products austenitic and duplex stainless steel con-cast Blooms to 365mm wide, to 7500mm long; Con-cast Billets to 150mm wide, to 6200mm long;As rolled billets to 195mm wide, to 6000mm long; semi-finished as rolled bars to 185mm diameter, 6900mm long for further processing for Rolled, ForgedProducts
As belowE.A.F. / Con CastSteelmakingOUTOKUMPU STAINLESS AB Stockholm304L, 304LN, 316L, 321, 347 12Austenitic StainlessPlatesUNS S31803, UNS 32205* 8Duplex Stainless304L, 316L, 321, 347 8Austenitic StainlessHot Rolled Coil
Box 74SE-774 22 Avesta
Business Unit Special Coil & Plate
Tel: +46 (0)226 81832 Fax: +46 (0)226 813 16 E-mail mailto:[email protected] Web: http://www.outokumpu.com*accepted for approved applicationsCertificate No. MD00/0131/0006/1 Expiry date: 08/12/2011
304L, 316L, 317L, 321 5Austenitic StainlessCoilOUTOKUMPU STAINLESS AB Stockholm
SE-64480 TorshällaThin Strip Nyby
Tel +46 (0)1634 9000 Fax +46 (0)1634 9014 Email: mailto:claes.gefvenberg@outokumpuCertificate No. MD00/0132/0005/1 Expiry date: 30/01/2013
304L, 316L, 316LN, 321 50Austenitic StainlessPlatesOUTOKUMPU STAINLESS AB KristinehamnUNS S32304** 10Duplex StainlessUNS S31803(MOD)* 50
S-693 81 Degerfors,
Business Unit Special Plate,Quarto Plate Europe,
Tel: 46 586 47000 Fax: 46 586 47019 Email: mailto:[email protected] Web: http://www.outokumpu.com* accepted for approved applications** Grade UNS 32304 may be accepted as equivalent to 316L as shown in LR Rules when properties meet the Rule requirements.
Certificate Number MD00/1754/0006/1 Expiry date: 14/11/2014
UNS S31803, UNS S32205* 200Duplex StainlessBarsOUTOKUMPU STAINLESS AB Kristinehamn
SE-693 81 DegerforsDegerfors Stainless
Tel: +46 (0)586 47000/47 232 Fax: +46 (0)586 47008Email mailto:[email protected] Web http://www.outokumpu.comEN 10088-1 grade 1.4462 accepted for approved applications only.Certificate number MD00/3144/0004/1 Expiry date: 08/06/2014
As at 06 November 2012 65Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
A, B, D, E 50Normal StrengthSectionsOVAKO BAR AB. StockholmAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
A, B, D, E 45Normal StrengthBarsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
45Higher Strength
Box 559010 Boxholm
Boxholm Works
Tel: +46 0142 293600 Fax: +46 0142 293702 Email mailto: [email protected] Web http://www.ovako.com Certificate No. MD00/0560/0008/1 Expiry date: 27/09/2014
As belowE.A.F. / Con CastSteelmakingOVAKO BAR AB. StockholmA, B, D, E 50Normal StrengthSectionsAH32, AH36, DH32, DH36, EH32, EH36 50Higher StrengthA, B, D, E 93Normal StrengthBarsAH32, AH36, DH32, DH36, EH32, EH36 93Higher Strengthcarbon, carbon-manganese 93Machinery
Smedjebacken WorksS-777 80 SmedjebackenTel. +46 (0)240 668355 Fax +46 (0)240 668168 EMail mailto: [email protected] Web http://www.ovako.comCertificate #: MD00/0561/0005/1 Expiry date: 11/06/2013
As belowE.A.F. / IngotSteelmakingOVAKO HOFORS AB Stockholmcarbon, carbon-manganese, alloy 400BilletsSemi-Finishedcarbon, carbon-manganese, alloy 450Barscarbon, carbon-manganese, alloy 190StructuralBarscarbon, carbon-manganese, alloy 170MachineryU3, R3, R3S, R4 165Chain Cable Stock
Se-813 82 HOFORSTel: +46 (0) 298 25000 Fax: +46 0298 25025 Email: mailto:[email protected] Web: www.ovako.comCertificate No. MD00/1167/0005/1 Expiry date: 28/11/2011
carbon, carbon-manganese, alloy 165StructuralBarsOVAKO HOFORS AB Kristinehamncarbon, carbon-manganese, alloy 165MachineryU1, U2, U3, R3, R3S, R4 165Chain Cable Stock
71280 Hällefors
Bar DivisionHällefors
Tel: +46 591 60375 Fax: +46 591 60623 Email: mailto:[email protected] No. MD00/3747/0001/1 Expiry date: 17.12.2011
As belowB.O.S. / Con CastSteelmakingSSAB EMEA AB StockholmAs below 286SlabsSemi-FinishedA, B, D, E 75Normal StrengthPlatesFH27S 40Higher StrengthAH27S, AH32, AH36, AH40, AH42, DH27S,DH32, DH36, DH40, EH27S, EH36
60
DH42, EH32, EH40, EH42, FH32, FH36, FH40,FH42
70
AH46, AH50, AH55, AH62, AH69, DH46, DH50,DH55, DH62, DH69, EH46, EH50, EH55, EH62,EH69, FH46, FH50, FH55, FH62, FH69
80
460FG, 490FG, 510FG 60Boiler & Pressure Vessel360FG, 410FG 75LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40, LTFH27S,LTFH32, LTFH36, LTFH40
40Ferritic Low Temperature
S-61380 OxelösundOXELÖSUND
Tel +46 155 254783 Fax +46 155 254082 Email: mailto:[email protected] Web:http://www.ssab.comAll plates with specified through thickness properties.Semi-finished products in carbon and carbon-manganese steel with fine grain (element combinations as stated), slabs to 1680 mm wide, to 11000mm long ofmaximum weight 30T for further processing to rolled productsMaterials Quality Scheme Approved - Approval No. MQS 049Certificate No. MD00/1282/0009/1 Expiry date: 25/04/2013
As at 06 November 2012 66Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Switzerland
As belowE.A.F. / Con CastSteelmakingSTAHL GERLAFINGEN AG StuttgartA, B 15Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36 10Higher Strength
BahnhofstrasseCH-4563 GerlafingenTel: +41 (0)32 674 2568 Fax: +41 (0)32 674 2842 Email: [email protected] No. MD00/3438/0002/1 Expiry date: 01/03/2014
Taiwan, Republic of China
As belowB.O.S. / Con CastSteelmakingCHINA STEEL CORPORATION KaohsiungNormal strength, Higher Strength 270SlabsSemi-FinishedA, B, D, E 50Normal StrengthPlatesAH47, DH47, EH47 65Higher StrengthAH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
75
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50
No.1 Chung Kang RoadHsiao Kang
Tel: +886 7 802 1111 ext 2208 Fax: +886 7 805 1292Email: [email protected] page: www.csc.com.tw All grades are approved with specified with through thickness properties.Certificate No. MD00/0304/0008/1 Expiry date: 06/04/2014
Kaohsiung
AH32, AH36, DH32, DH36 26Higher StrengthSectionsDRAGON STEEL CORPORATION Kaohsiung
Longjing Dist.,Taichung City
100, Longchang Road,
Tel No. +886 4 2630 6088 EXT 6515 Fax No. +886 4 2630 6041Email [email protected] www.dragonsteel.com.twCertificate no MD00/3768/0003/1 Expiry date: 03/04/2013
A 15Normal StrengthSectionsT. S. STEEL COMPANY LTD. KaohsiungAH32, AH36 12Higher StrengthA 25Normal StrengthBars
Tsuang-Hine Industrial ZoneHsen-Kang Road
No.6 Kon-Sixth Road
Tel: +886 4 798 0060 ext 12 Fax: +886 4 799 1522Email: [email protected] No. MD00/2313/0006/1 Expiry date: 10/04/2014
Chang-Hua Hsien
As belowE.A.F. / Con CastSteelmakingTUNG HO STEEL ENTERPRISE CORP. Taipeicarbon, carbon-manganese 430BloomsSemi-Finished
No.22, Pingding Erhu Village,Sihu Township,
Miao Li Works
Tel: +88 637 92333 Fax: +88 637 923311 Email mailto:[email protected] Web http://www.tunghosteel.comCertifcate Number: MD00/3719/0001/1 Expiry date: 15/12/2012
Miaoli County 36842,
A 18Normal StrengthSectionsTUNG HO STEEL ENTERPRISE CORP. TaipeiAH27S, AH32, AH36 18Higher Strength
No. 8, Chia Hsing Street,Hsiao Kang,
Kaohsiung Works
Tel: +88 6 7802 3131 Fax: +88 6 801 0696 Email mailto:[email protected] Web http://www.tunghosteel.comCertificate Number: MD00/3720/0001/1 Expiry date: 16/12/2012
Kaohsiung City
austenitic stainless, duplex stainlessE.A.F. / Con CastSteelmakingWALSIN LIHWA CORP. Kaohsiungaustenitic stainless, duplex stainless 200SlabsSemi-Finishedaustenitic stainless, duplex stainless 240Billets
As at 06 November 2012 67Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Chin Shuei LiYenshui Chen
Yenshui Plant3-10 Shi Jou Liau
Tel +886 6 6520911 ext. 407 Fax +886 6 6533076 Email mailto:[email protected] Web http://www.walsin.comCertificate No. MD00/3063/0003/1 Expiry date: 15/03/2013
Semi Finished Products Austentic & Duplex Stainless slabs to 1300mm wide, to 12000mm long; square billets to 155mm wide, 12000mm long; round billets withmaximum diameter 240mm , to 12000mm long
737 Tainan Hsien
Thailand
A 50Normal StrengthPlatesLPN PLATE MILL PUBLIC COMPANY LIMITED Bangkok360AR, 410AR 40Boiler & Pressure Vessel
Pakklong BangplakodPrasamutjedee
199/9 Moo 4 Suksawad Road
Tel: +66 2815 6400-9 Fax: +66 2815 6415 Email: mailto:[email protected]: www.lpnpm.co.thCertificate No. MD00/2578/0006/1 Expiry date: 02/09/2014
Samutprakarn 10290
A, B 40Normal StrengthPlatesSAHAVIRIYA PLATE MILL PUBLIC COMPANYLIMITED
Bangkok
360AR, 410AR 32Boiler & Pressure Vessel
160 Moo 14 Sukhumvit RoadBangpakong
Chachoengsao
Tel: +66 3883 2056 ext 162 Fax: +66 3853 2370 Email mailto: [email protected] No. MD00/2579/0006/1 Expiry date: 01/09/2014
Chachoengsao 24130
B, D 8Normal StrengthHot Rolled CoilSAHAVIRIYA STEEL INDUSTRIES PUBLICCOMPANY LIMITED
Bangkok
A 19
360, 410 19Boiler & Pressure Vessel
B, D 8Normal StrengthPlates from coils
A 19
360AR, 410AR 19Boiler and Pressure Vessel
9M.7 Tumbol MearumphuengAmphur Bang Saphan
Prachuab Kirikhan
Tel: (+66) 32 691403-5 ext 5118 Fax: (+66) 32 691408 Email mailto: [email protected] Web http://www.ssi-steel.comCertificate No. MD00/3764/0001/1 Expiry date: 24/09/2012
Prachuab Kirikhan 77140
Tunisia
A 25Normal StrengthFabricated SectionsPALESCANDOLO CNT sarl NaplesAH32, AH36 25Higher Strength
Parc D' Activite' Economique De Bizerte7000 BizerteTel: + 21 77 241 7292 Fax: +21 77 241 7552 Email: [email protected] Certificate Number: MD00/4018/0001/1 Expiry: 26/04/2012
As at 06 November 2012 68Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
Turkey
As belowE.A.F./Ingot/Con CastSteelmakingASIL CELIK SANAYI VE TICARET A.S. Istanbulcarbon, carbon-manganese, alloy 300StructuralBarscarbon, carbon-manganese, alloy 220Machinery
Gemic Koyu Mevki 16800Orhangazi, BursaTel: +90 224 280 61 00 Fax: +90 224 280 62 00 Email mailto:[email protected] http://www.asilcelik.com.trCertificate No. MD00/1921/0005/1 Expiry date: 06/05/2013
As belowB.O.S. / Con CastSteelmakingEREGLI DEMIR VE CELIK FABRIKALARI T.A.S. IstanbulA, B, D, E 60Normal StrengthPlatesAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36, FH27S, FH32, FH36
60Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 60Boiler & Pressure VesselA, B, D, E 15Normal StrengthHot Rolled CoilAH32, AH36, DH32, DH36, EH27S, EH32, EH36,FH27S, FH32, FH36
15Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 15Boiler & Pressure VesselKDZ. Eregli67330
Tel: +90 (0)372 329 3838 Fax: +90 (0)372 323 2598 Email: mailto:[email protected] Web http://www.erdemir.com.trCertificate No. MD00/1951/0009/1 Expiry date: 06/05/2014
Zonguldak
As belowE.A.F. / Con CastSteelmakingÖZKAN DEMIR ÇELIK SANAYI A.S. Istanbulcarbon, carbon manganese 260Blooms/BilletsSemi-FinishedD, E 12Normal StrengthSectionsA, B 25AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
28Higher Strength
Bozköy Köyü13. Cadde N:4 35800
Tel +90 232 625 1010 Fax +90 232 625 1111Email: [email protected]: http://www.ozkansteel.comCertificate No. MD00/2984/0003/1 Expiry date: 02/04/2014
Aliaga-Izmir
Ukraine
As BelowOH/Ingot/ Con CastSteelmakingCJSC DONETSKSTEEL IRON AND STEEL WORKS Mykolaivcarbon, carbon-manganese 5IngotsSemi-Finishedcarbon, carbon-manganese 150Slabs
141 Tkachenko StDonetsk region
Tel: +38 (0622) 61-27-44 or 61-31-62 Fax: +38 (062) 388 04 21 Email: mailto:[email protected] No. MD00/3134/0003/1 Expiry date: 27/01/2014
83062 Donetsk
carbon, carbon-manganeseE.A.F. / IngotSteelmakingJSC "DNERPOTYAZHMASH" Mykolaiv
Post Code 49600Dnepropetrovsk
3, Sukhoi Ostrov St.
Tel: +38 (056) 3703037 Fax: +38 (056) 3703037 Email: [email protected] Web: eee.dtm.dp.uaCertificate No. MD00/2825/0004/1 Expiry date: 19/09/2013
As belowE.A.F. / IngotSteelmakingJSC ELECTROMETALLURGICAL WORKSDNEPROSPETSSTAL
Mykolaiv
304L, 316L, 321 215Austenitic StainlessBars
carbon, carbon-manganese, alloy 300Machinery
U1, U2, U3 85Chain Cable Stock
81 Yuzhnoye ShosseZaporozhye, 69008
after A.N. Kuzmin
Tel: +38 612 223 627 Fax No: +38 612 131 780Email : [email protected] http://www.dss-ua.comIncluding forged bars and tube blanks ( billets) in all qualities.Certificate No. MD00/2225/0006/1 Expiry date: 05/07/2013
As at 06 November 2012 69Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
As BelowOH/Ingot/ Con CastSteelmakingPJSC "ALCHEVSK IRON & STEEL WORKS" MykolaivNormal strength, Higher Strength 300SlabsSemi-FinishedD, E 45Normal StrengthPlatesB 50A 72AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
360AR, 410AR 22Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 50360, 410 72A 8Normal StrengthSectionsA 100Normal StrengthBars
Lugansk Region94202
Shmidt st. 4, Alchevsk
Tel: +38 06442 7 33 20 Fax: +38 06442 97 33 76 EMail: mailto:[email protected] Web page http://www.amk.lg.uaCertificate No. MD00/0088/0008/1 Expiry date: 28/07/2014
As belowB.O.S. / Con CastSteelmakingPJSC "AZOVSTAL IRON & STEEL WORKS" MykolaivNormal strength, Higher Strength 270SlabsSemi-FinishedD, E 50Normal StrengthPlatesA, B 100AH27S, AH32, AH36, AH40, DH27S, DH32,DH36, DH40, EH27S, EH32, EH36, EH40
50Higher Strength
360, 410, 360FG, 410FG, 460FG, 490FG, 510FG 50Boiler & Pressure Vessel1, Leporsky St.Mariupol 87500Tel: +380 629 467 108 Fax: +380 629 468 441 Telex: 115123 VOLNA UX Email mailto:sal@@azovstal.com.ua Web http://www.azovstal.metinvestholding.comIncluding plates with specified through thickness properties. Z35 may be applied to all grades and thicknessesCertificate No. MD00/0779/0008/1 Expiry date: 15/02/2015
D 16Normal StrengthPlatesPJSC "DONETSK IRON AND STEEL WORKS" MykolaivA, B 20DH27S, DH32 16Higher StrengthAH27S, AH32 20360AR, 410AR 20Boiler & Pressure Vessel
122 Tkachenko StDonetsk 83062Tel: +38 0622 61 26 35 Fax: +38 0623 3880 421 Email:mailto:[email protected] No. MD00/2239/0006/1 Expiry date: 10/07/2013
As belowE.A.F. / IngotSteelmakingPJSC "ENERGOMASHSPETSSTAL" Mykolaivcarbon, carbon-manganese, alloy 250IngotsSemi-Finished
Donetsk Region84306 Kramatorsk
Tel: +38 (06264) 6-94-93 Fax: +38 (06264) 6-94-93Email: [email protected] No. MD00/3575/0001/1 Expiry date: 16/03/2015
As belowB.O.S. / Con CastSteelmakingPJSC "ILYICH IRON AND STEEL WORKS" MykolaivE 50Normal StrengthPlatesA, B, D 80DH40, EH40 25Higher StrengthAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50
360AR, 410AR, 460AR 25Boiler & Pressure Vessel360FG, 410FG 80
1 Levchenko StreetMariupol 87504All grades and thicknesses with specified through thickness properties. Notation Z25 or Z35 may be added.Tel: +38 (0)0 629 4343 23 Fax: +38 (0)62 5300 39 Web http://www.ilyich.com.uaCertificate No. MD00/0775/0005/1 Expiry date: 03/07/2013
As belowB.O.S. / IngotSteelmakingPJSC ENAKIEVO IRON AND STEEL WORKS Mykolaivcarbon, carbon-manganese 9IngotsSemi-FinishedA, B 11Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32 11Higher Strength
YenakievoDonetsk region
Metallurgov Avenue, 9
Tel +38 (0)6252 92318 Fax +38 (0)6252 92235 Telex 115738"shlak" Email:yurly.anikanov@enakievosteelCertificate No. MD00/3121/0003/1 Expiry date: 05/12/2013
86429
As at 06 November 2012 70Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
United Kingdom
A, B, D, E 12Normal StrengthSectionsCAPARO MERCHANT BAR PLC. ScunthorpeAH32, AH36, DH32, DH36 12Higher StrengthA, B, D, E 50Normal StrengthBarsAH32, AH36, DH32, DH36 50Higher Strength
P.O. Box 15Scunthorpe
Caparo House
Tel +44 (0)1724 403022 Fax +44 (0)1724 403044Email: mailto:[email protected] Web: www.cmbplc.co.ukCertificate No. MD00/1599/0006/1 Expiry date: 30/11/2012
DN16 1XL
AH32, AH36, DH32 18Higher StrengthFabricated SectionsCELLBEAM LTD. LiverpoolDH36 30EH46-TM 20High Strength
Thorp Arch Trading Estate Wetherby
Tel: +44 (0)1737 840600 Email: [email protected] Web: www.cellbeam.co.ukCertificate No. MD00/3534/0004/1 Expiry date: 11/11/2014
West Yorkshire LS23 7DB
As belowE.A.F. / Con CastSteelmakingCELSA MANUFACTURING (UK) LTD. SouthamptonNormal Strength 140Blooms/BilletsSemi-FinishedA 25Normal StrengthSections
Seawall Road,Tremorfa,
Sections MillTremorfa Works
Tel: +44 (0) 1568 615201 Fax: +44 (0) 1568 612626Certificate No. MD00/3552/0003/1 Expiry date: 16/12/2014
Concast blooms/billets covers billets to 140mm x140mm and concast 'mini slabs' to 280 x 120mm.
Cardiff. CF24 5TH
A 50Normal StrengthSectionsNIAGARA (HOT ROLLED) Coventry (UKInd. Operations)
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
32Higher Strength
A 50Normal StrengthBars
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
Peartree LaneWoodside, Dudley
Tel: +44 (0) 1384 471200 Fax: +44 (0)1384 471201 Email: mailto:[email protected] Web: http://www.niag.comCertificate No. MD00/2618/0006/1 Expiry date: 21/02/2013
West Midlands DY2 0QS
stainless steelE.A.F/A.O.D/L.A.F/ConCastSteelmakingOUTOKUMPU STAINLESS LTD. Scunthorpestainless steels 5IngotsSemi-Finishedstainless steel 30Slabsstainless steel 30Blooms/Billets
P.O. Box 161Europa Link
LONG PRODUCTS BUSINESS UNIT, SMACC
The approval for steelmaking and ingots, slabs, blooms and billets in stainless steel covers the supply of austenitic, duplex, ferritic, martensitic and precipitationhardening grades, in accordance with the Society's Rules for the Manufacture, Testing and Certification of Materials, Chapter 3 or appropriate international ornational standards. The final processing mill is responsible for ordering steel which complies with their surface and internal quality standards and approvedchemical composition to enables them to achieve the required physical and mechanical properties.
Tel: +44 (0)114 2616292 Fax: +44 0114 2616163 Email: mailto:[email protected] Web: http://www.outokumpu.comCertificate No. MD00/1883/0006/1 Expiry date: 03/01/2013
Sheffield, S9 1TZ
As belowB.O.S. / Con CastSteelmakingSAHAVIRIYA STEEL INDUSTRIES UK Liverpoolcarbon, carbon-manganese 305SlabsSemi-Finished
Steel HouseRedcar
Tel: +44 01642 408053 Email: [email protected] Web: http://www.ssi-steel.co.uk Certificate No. MD00/4057/0001/1 Expiry date: 22/07/2015
TS10 5QW
As at 06 November 2012 71Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
carbon, carbon-manganese, alloy, austeniticstainless
E.A.F. / IngotSteelmakingSHEFFIELD FORGEMASTERS INTERNATIONALLTD.
Scunthorpe
Brightside LaneSheffield S9 2RW
P.O. Box 286
Tel: +44 (0)114 2449071 Fax: +44 (0)114 2422103 Email:mailto:[email protected] Web:http://www.sheffieldforgemasters.comCertificate No. MD00/0524/0007/1 Expiry date: 01/07/2014
E 50Normal StrengthPlatesTATA STEEL (UK) LTD GlasgowA, B, D 100FH40 25Higher StrengthFH32, FH36 30AH42, AH46 36AH40, DH40, DH42, DH46, EH40, EH42, EH46 65AH32, AH36, DH32, DH36, EH32, EH36 75460FG, 490FG, 510FG 75Boiler & Pressure Vessel360FG, 410FG 100LTFH40 25Ferritic Low TemperatureLTAH32, LTAH36, LTAH40, LTDH32, LTDH36,LTDH40, LTEH32, LTEH36, LTEH40, LTFH32,LTFH36
30
Motherwell ML1 1PUDalzell
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.corusgroup.comAll plates with specified through thickness properties.Materials Quality Scheme Approved - Approval No. MQS030Certificate No. MD00/0235/0009/1 Expiry date: 19/05/2014
As belowB.O.S./Ingot/Con CastSteelmakingTATA STEEL (UK) LTD Scunthorpecarbon, carbon-manganese 305SlabsSemi-Finishedcarbon, carbon-manganese 355Blooms/BilletsE 50Normal StrengthPlatesB, D 60A 80FH40, FH42, FH46 25Higher StrengthAH40, AH42, AH46, DH40, DH42, DH46, EH40,EH42, EH46
30
FH32, FH36 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
70
360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG, 460FG, 490FG, 510FG 70360, 410 80LTAH27S, LTAH32, LTAH36, LTAH40,LTDH27S, LTDH32, LTDH36, LTDH40,LTEH27S, LTEH32, LTEH36, LTEH40
30Ferritic Low Temperature
A, B, D, E 50Normal StrengthSectionsAH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
50Higher Strength
P.O. Box 1Scunthorpe DN16 1BP
Scunthorpe
Tel: +44 1724 404040 Email:maito: [email protected] Web:http://www.tatasteel.comAll plates with through thickness properties.Materials Quality Scheme Approved - Approval No. MQS029Certificate #: MD00/0240/0012/1 Expiry date: 24/07/2012
A, B, D, E 77Normal StrengthSectionsTATA STEEL (UK) LTD MiddlesbroughAH27S, AH32, AH36, DH27S, DH32, DH36 77Higher Strength
RedcarTeesside
Teesside
Tel: +44 (0)1642 406583 Fax: +44 (0)1642 406904 Email: mailto:[email protected]
Materials Quality Scheme Approved - Approval No. MQS031Certificate #: MD00/0242/0013/1 Expiry date: 02/06/2014
TS10 5RD
A, B, D, E 20Normal StrengthSectionsTATA STEEL (UK) LTD Newcastle uponTyne
AH40, DH40 15Higher Strength
AH32, AH36, DH32, DH36, EH32, EH36 20
As at 06 November 2012 72Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
P.O. Box 1Saltburn by the Sea
Skinningrove
Tel: +44 (0)1287 640212 Fax: +44 (0)1287 643467 Email: mailto:[email protected]
Materials Quality Scheme Approved - Approval No. MQS032Certificate #: MD00/0243/0010/1 Expiry date: 18/08/2014
TS13 4ET
As belowB.O.S. / Con CastSteelmakingTATA STEEL (UK) LTD Newcastle uponTyne
carbon, carbon-manganese 295SlabsSemi-Finished
carbon, carbon-manganese 305Blooms/Billets
Steel HouseRedcar
Teesside Cast Products
Materials Quality Scheme Approved - Approval No. MQS 033Certificate #: MD00/3130/0004/1 Expiry date: 03/06/2011
Teesside, TS10 5RD
carbon, carbon-manganese 16Structural SectionsFabricated SectionsTATA STEEL UK LIMITED Coventry (UKInd. Operations)
CorbyNorthamptonshire
Corby WorksP.O. Box 101, Weldon Road
Tel: +44 (0)1536 404704 Fax: +44 (0)1536 404212 Email: mailto:[email protected] Web: http://www.tatasteel.comIncludes fabricated hollow sectionsCertificate No. MD00/0234/0001/1 Expiry date: 26/02/2015
NN17 5UA
A 20Normal StrengthSectionsTATA STEEL UK LIMITED Newcastle uponTyne
AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
20Higher Strength
carbon, carbon-manganese 20Structural SectionsFabricated Sections
Brenda RoadHartlepool
Hartlepool Works20 Inch H.F.I. Pipe Mill
Tel: +44 (0)1429 527249 Mob: +44 (0)7743 842969 Email: mailto:[email protected] Web:http://www.tatasteeleurope.comCertificate #: MD00/0236/0007/1 Expiry date: 10/09/2014
Teeside TS25 2EG
carbon, carbon-manganese, alloyE.A.F./Ingot/Con CastSteelmakingTATA STEEL UK LIMITED Scunthorpeas below 13IngotsSemi-Finishedcarbon, carbon-manganese, alloy 381Semi-finished ProductsBarscarbon, carbon-manganese, alloy 300MachineryU1, U2, U3, R3, R3S, R4 165Chain Cable Stock
StocksbridgeSheffield
Rotherham & Stocksbridge Sites
Tel: +44 (0)114 2832043 Fax: Email mailto:[email protected] Web page http://www.tatasteeleurope.comCertificate No. MD00/1593/0006/1 Expiry date: 04/07/2014
South Yorkshire S36 2JA
As belowB.O.S. / Con CastSteelmakingTATA STEEL UK LIMITED Liverpoolcarbon, carbon-manganese 238SlabsSemi-Finished
Port TalbotSA13 2NG
Port Talbot Works
Tel: +44 (0)1698 266100 Fax: +44 (0) 1698 266100 Ext. 394 Web page http:\\www.corusgroup.comApproval covers concast slabs to nominal size 1850mm wide x 10,000mm long to the maximum thickness for further processing to rolled products.
Certificate No.: MD00/3909/0001/1 Expiry Date: 05.05.2014
As at 06 November 2012 73Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
United States of America
As belowB.O.S. / Con CastSteelmakingARCELORMITTAL BURNS HARBOR ChicagoD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH27S, DH32, DH36,EH27S, EH32, EH36
75Higher Strength
Burns HarborIN 46304-9745
250 West Highway 12
Tel: +1 219 787 4553 Fax: 1 219 787 2139 Email mailto:[email protected] Certificate No. MD00/2331/0005/1 Expiry date: 18/12/2012
carbon, carbon-manganese, alloyE.A.F. / IngotSteelmakingELLWOOD QUALITY STEEL COMPANY Chicagocarbon, carbon-manganese, alloy 38IngotsSemi-Finished
700 Moravia StreetNew Castle
Tel: +1 724 658 6849 Fax: +1 724 658 6802Email mailto:[email protected]: www.egi.orgCertificate No. MD00/2652/0005/1 Expiry date: 15/02/2015
Pennsylvania 16101
As below 248E.A.F. / Con CastSteelmakingEVRAZ CLAYMONT STEEL, PhiladelphiaA, B 75Normal StrengthPlates
Claymont,Delaware,
4001 Philadelphia Pike,
Tel No. +01 302 792 5400 Fax No. +01 302 792 0203Email: scott. [email protected]: www.EvrazIncNA.comCertificate No. MD00/3833/0001/1 Expiry date: 22/09/2013
19703
A, B, D 50Normal StrengthPlatesEVRAZ OREGON STEEL MILLS Los AngelesAH27S, AH32, AH36, DH27S, DH32, DH36 12Higher Strength360AR, 410AR 40Boiler & Pressure Vessel360FG, 410FG 50
14400 N. Rivergate Blvd.Portland
Tel: +1 503 978 6130 Fax: +1 503 978 4975Email: mailto:[email protected] Web http://www.evrazincna.comIncluding all plate grades and thicknesses with specified through thickness properties (Z35)
MATERIALS QUALITY SCHEME APPROVED - MQS 047Certificate No. MD00/1152/0006/1 Expiry date: 01/06/2015
OR 97203
E 51Normal StrengthPlatesJSW STEEL (USA) INC. HoustonA, B, D 102AH27S, AH32, AH36, DH27S, DH32, DH36,DH40
102Higher Strength
360FG, 410FG, 460FG, 490FG, 510FG 102Boiler & Pressure Vessel5200 East McKinney RoadBaytown
Tel: +1 281 383 5100 Fax: +1 281 383 1803 Email mailto: [email protected] Web: http://www.jswsteel.comCertificate No. MD00/3505/0002/1 Expiry date: 26/08/2014
Texas 77523
As belowE.A.F. / Con CastSteelmakingNUCOR STEEL MEMPHIS, INC ChicagoCarbon, Carbon-manganese, Alloy 203Rolled Round BarsSemi-FinishedCarbon, Carbon-manganese, Alloy 511As Cast Round SectionCarbon, Carbon-manganese, Alloy 254Rolled Square Bars
MemphisTN 38109
3601 Paul R. Lowry Road
Tel: +1 901 786 5416 Fax: +1 901 788 5300 Email to: [email protected] Web http://www.nucor.com
Certificate No. MD00/4059/0001/1 Expiry date: 22/07/2015
As belowE.A.F. / Con CastSteelmakingNUCOR STEEL TUSCALOOSA INC. New OrleansA 20Normal StrengthHot Rolled Coil360FG, 410FG 20Boiler & Pressure VesselA 20Normal StrengthPlates from coilsAH27S, DH27S, AH32, DH32, AH36, DH36 13Higher Strength
As at 06 November 2012 74Page
Name and Address Max Thickness/Diameter (mm)GradeCategoryProduct
List 1Approved Steelmakers and Manufacturers of
Rolled Steel Plates, Strip, Sections & Bars
LR Office
TuscaloosaAL 35404-1000
1700 Holt Road N.E.
Tel: +1 205 562 1200 Fax: +1 205 556 1482 Email to: [email protected] Web http://www.nucor.com
Materials Quality Scheme approved - MQS048
Certificate No. MD00/3323/0004/1 Expiry date: 05/08/2015
As belowE.A.F./Ingot/Con CastSteelmakingREPUBLIC ENGINEERED PRODUCTS Chicagocarbon, carbon-manganese, alloy 14IngotsSemi-Finishedcarbon, carbon-manganese 365Semi-finished ProductsBars
2633 Eighth Street N.E.Canton
HOT ROLLED BAR DIVISIONCANTON WORKS
Tel: +1 330 438 5541 Fax: +1 330 438 5213 Email: mailto:[email protected] Web: http://www.republicengineered.comIngots as semi finished products, nominal 740mm diameter x 4800mm, are approved for further processing for forgings to the maximum un-cropped weightshown above.Certificate #: MD00/2236/0005/1 Expiry date: 15/05/2013
Ohio 44704-2311
As belowE.A.F. / Con CastSteelmakingSSAB ALABAMA, INC. New OrleansD 35Normal StrengthPlatesA, B 50AH27S, AH32, AH36, DH32, DH36 38Higher Strength360FG, 410FG, 460FG, 490FG, 510FG 38Boiler & Pressure Vessel
AxisAlabama 36050
12400 Highway 43 North
Tel: + 01 256-546-2669 Fax: +01 256-546-2670 email mailto:[email protected] Web http://www.ipsco.com
Materials Quality Scheme Approved - MQS 042Certificate No. MD00/3108/0006/1 Expiry date: 30/03/2014
As belowE.A.F./Ingot/Con CastSteelmakingTHE TIMKEN COMPANY STEEL BUSINESS Chicagocarbon, carbon-manganese, alloy 330BarsSemi-Finished
CantonOH 44706-0932
1835 Dueber Avenue S.W.
TTel: +1 330 471 3263 Fax: +1 330 471 4077 Email: mailto:[email protected] Werb: http://www.timken.comBars as Semi Finished Products approved for further processing for forgings and for use as billets for seamless tube production.Certificate No. MD00/1510/0005/1 Expiry date: 12/01/2014
As at 06 November 2012 75Page