Lionel 100 Anniversary 700E J-1E Hudson 4-6-4 … 8/00 featuring and Lionel 100 TH Anniversary 700E...

72-8062-2508/00

featuring and

Lionel 100TH Anniversary700E J-1E Hudson

4-6-4 Steam Locomotive

Congratulations!

2

You own one of the most sophisticatedmodel trains ever built—the Lionel

TrainMaster® Command-equipped Gold700E Hudson. From its scale details to the

advanced technology present inside, yourGold 700E Hudson is ready for duty on yourmodel railroad layout. Experience the super-iority of today’s Lionel.

Table of contents

Transformer operations PageRunning your Lionel Gold 700E Hudson with a Lionel transformer 3 Locking your Gold 700E Hudson into a single operational state 4Your Gold 700E Hudson’s RailSounds system—the basics 5Experiencing the range of your Gold 700E Hudson’s RailSounds system 6Notes on RailSounds 6Installing the Lionel sound activation button 7

TrainMaster Command operationsYour Gold 700E Hudson in the TrainMaster Command environment 8CAB-1 commands for your Hudson 9RailSounds in the Command environment 10CAB-1 numeric keypad commands for your Gold 700E Hudson 11Tuning your Gold 700E Hudson’s performance 12Maintaining your Gold 700E Hudson’s handrail antenna 13Assigning your Gold 700E Hudson a new ID# 14Reprogramming R2LC circuit boards to restore features 15

Maintaining and servicing your HudsonLubricating your Gold 700E Hudson 16Lubricating your Gold 700E Hudson’s Pullmor® motor armature 17Replacing your Gold 700E Hudson’s headlight 17Adding fluid to your Gold 700E Hudson’s smoke generator 18Caring for your Gold 700E Hudson’s appearance 19Lionel Service 20

• Powerful Pullmor® motor

• Liontech Command™ R2LC reverse unitfor use with the Lionel TrainMaster®

Command™ model railroad control system

• Smoke generator that produces clean, safe,and realistic smoke

• 2 Additional Traction Tires included

• Wireless Tether™

• RailSounds™ Hudson digital sound system

• Tire-Traction™

• Directional lighting

3

Transformer operations

Running your Lionel Gold 700E Hudson with a Lionel transformer

Place your Gold 700E Hudson on Lionel or Lionel-compatibleO gauge track.• Note the Traction-Enhancing Tire installed on the center drivers that gives

you Gold 700E Hudson extra driver-railhead grip. After extensive use, this tire mayrequire replacement. See your authorized Lionel Service Center for expert tirereplacement service. Lionel Traction-TirePart No. 610-8043-206.

• With track power OFF, Connect thedrawbar between locomotive and tender.Thats all you have to do with Lionel’s newWireless Tether® , an infrared communica-tion system that eliminates the plugs andwires of the past.

Power up your Gold 700E Hudson with your transformer.• Your Gold 700E Hudson is designed to operate on 10-18 volts

alternating current. Virtually all Lionel and Lionel-compatible alternating-current transformers are suitable; we recommend the TrainMaster Command modelrailroad control system.

• Do not power your Gold 700E Hudson with direct current (DC).Damage to sensitive electronic components may occur.

• When you first power up your track, the Gold 700E Hudson willwait between 3 and 8 seconds as it “listens” for digital language from theTrainMaster Command Base (available separately). When it’s determined that it’son a conventional (nonCommand) railroad, the Gold 700E Hudson’s headlight willilluminate and Railsounds will fire up. At this point, the Gold 700E Hudson is inneutral. (This occurs when placing the Hudson on your railroad for the first time.Thereafter, it starts in forward after every three-second power interruption.)

Note!

Move ‘em out!• Get your Gold 700E Hudson moving. Press the DIR button on your CAB-1

remote or Lionel transformer. This sequences the Liontech Command reverse unit(R2LC) to the next operating state.

• Adjust track voltage until your Hudson moves at your desired speed.

11

Your Lionel Gold 700E Hudson will negotiate 0-42 and larger curves.

22

33

Note!


4

T o select a single operational state foryour Lionel Gold 700E Hudson (exam-

ple: forward only), you can deactivate theR2LC’s sequencing function with the reverseunit control switch, located between thefront and center drivers on the right-handside, under the boiler casting.

Get your locomotive moving in the

desired direction, then slow it down withoutstopping. Set the reverse unit control switchto PROGRAM/LOCK. The Gold 700E Hudsonis now “locked” into your chosen direction.

When you no longer want single-direc-tion operation, just slide the reverse unitcontrol switch back to FORWARD/ RUN.

Locking your Gold 700E Hudson into a single operational state

FRONT

Forward/RunUse this setting fornormal operations.

Program/LockUse this setting to choosea single operational statelike “forward.”

5


Please remove protective cover from battery clip.

Although RailSounds is powered by track voltage, the battery is required for unin-terrupted operation. Use only alkaline batteries.

Discontinue locomotive power for 10 seconds before changing the RailSoundson/off switch position.

If RailSounds “drops out” during track power interruptions (direction change),replace the battery.

Your Gold 700E Hudson’s RailSounds system—the basics

Lionel RailSounds is the mostrealistic model railroad sound

system in the world. Your Gold 700EHudson features the RailSoundsHudson digital sound system for theultimate in realism.

Begin by in-stalling a 9-voltalkaline battery in the tender. Thisensures interuption free operationof your RailSounds. You mustremove the tender body from theframe to install the battery. Firstremove the 6 mounting screws fromthe underside of the tender. Carefully removethe tender body and connect the 9V alkalinebattery to the connector. Be careful not tocome in contact with the electronic compo-nents in the tender. These components arevery sensitive and damage may occur.Carefully replace the tender body on theframe and install the 6 screws.

When you first apply track power, theGold 700E Hudson’s RailSounds system pro-

duces sounds of a locomotive at rest. As yourHudson moves, chuffing begins, increasingwith the locomotive’s speed.

To silence the steam chuffing(whistle/bell are unaffected), slide theRailSounds switch, located under the tender,to the Off position before powering up thelocomotive. The whistle is activated by usingthe lever or button on your transformer orCAB-1.

Notes!

Volumecontrol dialON/OFF

MountingScrews

Install a 9-volt alkaline battery inyour Gold 700E Hudson’s tender.


6

W ith RailSounds, you experience thesounds of real railroading like never

before. Simply put, it’s the most sophisticat-ed, authentic model railroad sound system inthe world. And remember—inside yourLionel Gold 700E Hudson and tender are thesounds of the RailSounds Hudson digitalsound system. No other electric train canoffer you authentic Hudson sounds. That’sthe power of Lionel.

• Variable chuff rate. Your Gold 700E’sspeed determines the steam chuff rate.

• MultiWhistle™. Different whistlesevery time—a RailSounds exclusive.

• Authentic bell. Press BELL on yourCAB-1 or transformer to begin the effect,again to discontinue. Even the final “hit”is muted like the real thing.

• Reverse unit reset sound. Powerdown your track, wait for 3-5 seconds,and listen for the air-release sound—that’s the Gold 700E Hudson telling youits Liontech Command reverse unit hasjust reset to forward operation.

• Shutdown sequence. No other modelrailroad sound system shuts down likeRailSounds. Turn off track power, andafter the air-release reset sound, you havetwo seconds to restart your Gold 700EHudson. If you’re done with operations,RailSounds will commence with anauthentic Hudson shutdown sequenceabout two seconds after the air-releasereset occurs.

Experiencing the range of your Gold 700E Hudson’s RailSounds system

Notes on RailSounds

• Use the volume control dial located onthe underside of the tender to adjustsound output (see page 5).

• Listen for incidental engine sounds dur-ing RailSounds operation. They’re auto-matic and, of course, authentic.

• The 9-volt alkaline battery you installedensures continuous Hudson sounds, evenduring short track-power interruptions.

• Longer track-power interruptions(including locomotive derailments)cause RailSounds to shut down afterabout 7 seconds.

• For even more authentic RailSoundseffects, operate your Gold 700E Hudson inthe TrainMaster Command environment.See page 9 for details.

Battery must be installed forshutdown sequenceNote!

7


Installing the Lionel sound activation button

1 2

1 2

For AC transformers with a horn/whistle button

For AC transformers lacking a horn/whistle button

Attach to ground terminal

Attach to power terminal

Existing wire

Existing wire

Black wire

Red wire

Lionel no. 610-5906-001sound activation button foractivating the bell

To your transformer

Lionel no. 610-5906-001sound activationbutton for whistle

Lionel no. 610-5906-001sound activationbutton for bell

Black wire Red wire

Red wire

Attach toground terminal

Attach topower terminal

To your transformer

The no. 610-5906-001 button works with any Lionel AC transformer except no. 6-4690 Type MW. Transformers made by other manufacturers may not be compatiblewith RailSounds.

T o operate the bell and whistle soundswhen operating your Gold 700E Hudson

with conventional transformers, you’ll need

to install the Lionel no. 610-5906-001 soundactivation button (available separately).Connect the button(s) as shown below.

Note!

All track power must feedthrough the “Sound Activation Button”.Do not bypass button.

Note!

Trainmaster Command operations

8

Your Gold 700E Hudson in the TrainMaster Command environment

L ionel TrainMaster Command is the fun and sophisticated model railroad control

system. Your Gold 700E Hudson features theLiontech Command reverse unit, which actsas a conventional reverse unit as well as thekey to unlocking many extra features whenyou operate in Command mode.

TrainMaster Command gives you thepower to operate multiple Command-

equipped locomotives on the same track, atthe same time. It’s the most fun you canhave with electric trains, and it’s incrediblyeasy too! Just follow the directions below andyou’ll be on your way.

To operate in Command, youneed a Command Base and a CAB-1remote. Find them both at your authorizedLionel retailer.

Place your Gold 700E Hudson on Lionel or Lionel-compatible O gauge track.

• Make sure track power is OFF before placing it on track.• Make sure your Lionel Command Base is ON and its communications

wire is connected to the COMMON post on your Lionel transformer or the U on anyof your installed PowerMasters.

• Once positioned on the track, increase track voltage to FULL (onPowerMaster, slide the CMD/CONV switch to CMD).

Address your Gold 700E Hudson with CAB-1.

• Press ENG and 1 on the numeric keypad of your CAB-1 remote. This commandis sent by CAB-1 to the Command Base, which then translates your commands intodigital code. That code is sent around your railroad’s outside rails in the form of adigital “halo.” All Command-equipped Lionels listen to this digital communica-tion, but they do not respond until they hear their own ID number.

• The digital language of TrainMaster Command—and not track power—controlsthe actions of Command-equipped Lionels. Track power is simply like gasoline inthe tank of your car—it gives you the power to go places, but it doesn’t tell youwhere to go or how fast to get there.

• All Command-equipped Lionels come factory-programmed with anID# of “1.” To change your Gold 700E Hudson’s ID#, see page 14.

Move ‘em out!

• Throttle up or press any command button on CAB-1. Your Gold 700EHudson will respond to your every command. Read on. The fun is just beginning!

11

22

33

9


Tender rear couplerreleases. Couplerrelease sounds.

Press AUX2 to turnyour Gold 700E’s head-light on and off.

Press WSTL/HRN toactivate the Gold

700E’s whistle, release to dis-continue. Multi-Whistlesteam whistle sound.

Press DIR—the loco-motive decelerates to a

complete stop; turn the throttleup, and the locomotive movesin the opposite direction. Thereis no neutral. Steam air-release sound.

Press BELL once toactivate the bell,

again to discontinue.Traditional bell sound.

Press HALT to shut downall PowerMaster electri-cal output on your

railroad. Stops all Command-equipped Lionels in operation.

Turn the THROTTLEto the right to accel-erate, left to deceler-

ate. Speed-dependentvariable steam chuffing.DynaChuff dynamic chuffingeffect.

CAB-1 commands for your Gold 700E Hudson

Coupler releasesounds.

Press and hold BOOSTfor extra power.

Release BOOST and return tothe locomotive’s previousspeed. Labored chuff.

Press and hold BRAKE to slow down or stop. ReleaseBRAKE and return to the previous speed.

Squealing brake sounds.

Hudson RailSounds effects in bold italics

10


RailSounds in the Command environment

Your Gold 700E Hudson’s RailSounds sys-tem gives you even more in the

TrainMaster Command environment.

• DynaChuff™. Real steam locomotivechuffing depends on the locomotive’sload. DynaChuff simulates both laboredand relaxed chuffing sounds. Highballdown the mainline and hear the laboredchuffing of a locomotive battling inertia.Reduce your throttle setting, and chuff-

ing relaxes to a more sedate sound, asthough the load placed on the Gold 700EHudson has decreased. ExperienceDynaChuff on steep grades, at yardcrawls, and at speed. Another RailSoundsexclusive.

• Bonus sounds like squealing brakeswith the CAB-1 BRAKE command.

• Incidental sounds you control withCAB-1 numeric keypad commands, likesteam letoff and steam release effects.

TrainMaster Command operations

11

When you press AUX1 on CAB-1, youturn the numeric keypad into 10

command buttons. The keypad“stays open” and gives you access toextra command features until youpress any top-row button (SW, ACC,RTE, TR, or ENG). The CAB-1 keypad

overlay included with your Gold 700EHudson is designed to help you learn the

auxiliary features specific to thisclassic locomotive.

Hudson RailSounds effectsin bold italic.

CAB-1 numeric keypad commands for your Gold 700E Hudson

STEAMENGINERESET

VOLUME

SMOKE

SHUT

BLOWOFF

STEAMRELEASE

CREWTALK

TOWERCOM

DOWN

OFFPRESS

& HOLDSMOKE

BOOST

ON➠

➠

START-UP

AUX1

0Stops and resets the Gold 700E Hudsonto FORWARD. Headlight flickers.

1Raises the volume of RailSounds.Sound volume increases.

2CrewTalk™ is the sound of unintelligi-ble walkie-talkie communication.

3Starts up RailSounds. Startup sequencecommences. Steam blowoff sound.

4Lowers the volume of RailSounds.Sound volume decreases.

5Activates the RailSounds steam shut-down sequence. Just like the real thing,

your Gold 700E Hudson must be idle forshutdown to occur. Steam shutdowncommences. Remember, the whistle andbell will not sound until you restartRailSounds.

6Steam release sound.

7TowerCom™ is an audible announce-ment that includes that engine’s road

number and/or name. There is a four seconddelay in this function.

8Turns off the smoke generator.

9Turns on the smoke generator. Press andhold 9 (10 seconds maximum) to initi-

ate Smoke Boost™—it superheats thesmoke generator and enhances smoke outputwhen you start running your Gold 700EHudson.

Always keep smoke fluid in yourGold 700E Hudson’s smoke gener-

ator. Using Smoke Boost with depleted fluidcan damage the generator’s element.

Note!

12


Tuning your Gold 700E Hudson’s performance

MomentumSimulate the labored performance of a

locomotive pulling a heavy load withmomentum. Press L, M, or H (located underCAB-1’s removable panel) for light, medium,or heavy momentum. The R2LC remembersthe setting until you change it. For delayedresponse, use H. For quick response, choose L.

Boosting and BrakingUse the BOOST and BRAKE command

buttons for incremental control of speed anda superior method for handling grades,stops-and-starts, and more. Plus, usingBRAKE in the Command environment givesyou a bonus RailSounds effect—the ultra-realistic sound of squealing brakes.

StallMake your Gold 700E Hudson feel more

responsive by setting a “stall” voltage. Getyour locomotive moving, then press SET; theGold 700E Hudson will stop. The headlightwill flash, indicating it’s in the SET mode.Turn the throttle clockwise to get the enginemoving, then decrease speed until the loco-

motive just stops. Then press SET again; theR2LC remembers the stall setting until youchange it. To clear stall, press SET twice,holding it for one second each time.

High Voltage SettingPress SET, headlight will flash. Get your

locomotive moving to the maximum speedyou want it to run, press BOOST. Use this tokeep your locomotive from accidentallyderailing at high speed.To clear boost, pressSET, then BOOST, holding it for one second.

Sound QualityTo achieve your preferred RailSounds

master volume level, use the volume controldial located on the underside of the tender.(See page 5.) Turn the dial left or right toadjust the volume to your liking.

For quick remote-control of volumebelow the master setting—like muting—usethe CAB-1 numeric keypad’s volume control.Pressing AUX1 and 4 on the keypad lowersoverall RailSounds output.

13


Maintaining your Gold 700E Hudson’s handrail antenna

Your Gold 700E Hudson’s handrails aremore than just model grab irons—

they’re the R2LC’s antenna for receivingCommand Base digital communications.Please handle the Gold 700E Hudson careful-ly to avoid handrail damage. To ensure opti-mum reception, both handrails are insulatedfrom the die-cast shell. If your Gold 700E

Hudson experiences difficulty receiving Basecommunications, check the handrail ends inthe cab and pilot for the presence of insulat-ing material. Ensure each stanchion is pre-sent and enjoys a proper fit. Finally, preventthe handrails from touching any part of thedie-cast locomotive cab.


14

Assigning your Gold 700E Hudson a new ID#

As your Lionel Command-equipped fleetgrows, you’ll want to give your Gold

700E Hudson a more individualized ID#.Choose from any number between 1 and 99.To make things easy, use a portion of yourGold 700E Hudson’s cab number, for example 19.

Slide the Gold 700E Hudson’s reverse unitcontrol switch to PROGRAM (see the illustra-tion). Turn the Command Base ON and placethe Gold 700E Hudson on the track. Then,power up. Using CAB-1, press ENG, theengine ID# (example: 19), then press theSET button located under CAB-1’s removablepanel. See the headlight flash; that’s theR2LC confirming the new ID#. Slide theR2LC switch to FORWARD/RUN. Your Gold700E Hudson is ready to run with its all-newID#.

Assign a new ID# toyour Gold 700EHudson

Slide the Gold 700E Hudson’sreverse unit controlswitch to PROGRAM/LOCK

Command Base ON

Place the Gold 700E Hudson ontrack PowerMasters set to CMDor traditional power supplies onfull

Turn track power on(PowerMasters):

Press BOOST

Program the Gold 700E as Engine#19:

Press ENG

Press 19 (the ID#)

Press SET

See the headlight

Slide the reverse unit controlswitch to FORWARD/RUN

Your engine remembers its ID#forever; you can change it anytime by repeating these steps

Example

IMPORTANT

ENG

5 3

SET

Program/LockForward/Run

Slide the Gold 700E Hudson’s reverse unitcontrol switch to PROGRAM/ LOCK. Whenyou’ve finished ID# programming, slide theswitch to FORWARD/RUN.

Please make sure that the headlight is operationalin order to receive proper reset indication.

15


Reprogramming R2LC circuit boards to restore features

Step 1: Move switch on locomotive from runto program. See page 4 for switch location

Step 2: Turn on Command Base.

Step 3: Place locomotive on track, thenturn on power to track.

Step 4: Press “ENG” then input locomo-tive’s ID#. Press “SET”

Step 5: Press “ENG”, then the ID#, “AUX1”,then press 74 for this locomotive.

Step 6: Turn off power to track, wait tenseconds.

Step 7: Remove locomotive from track,move switch from program to run.

Step 8: Place locomotive back on track,turn power on to track.

Step 9: Press “ENG” and ID#, then operateas normal.

Due to the inevitable derailments, static,and the nature of electricity, it is possi-

ble that your R2LC could someday lose itssetup program. The symptoms of this condi-

tion would be unresponsiveness in commandmode. This can be easily remedied by “repro-gramming” your R2LC using the followingsteps.

Help your Lionel Gold 700E Hudson leada long and productive life on your

railroad by maintaining it properly. We recommend you purchase

a Lionel Lubrication andMaintenance Kit (part no. 6-62927), available from yourLionel dealer. Two basic rules tokeep in mind: never over-lubricate (a small amountwill do), and avoid gettinggrease or oil on the Gold700E Hudson’s wheels,contact rollers,

Traction-Tire, or your track. You’ll know your Gold 700E Hudson

requires lubrication when visualinspection reveals dryness on the

parts indicated in the illustration.Remove accumulated dirt anddust before lubricating, andalways lubricate any locomotiveemerging from prolonged stor-age. Also, lightly lubricate the

Gold 700E Hudson’s side rods,drive rods, and linkage after

each 25 hours of operation.

16

Maintaining and servicing your Gold 700E Hudson

Lubricating your Gold 700E Hudson

GREASEGREASE

GREASEGREASE

GREASEGREASELubricate axle endswith Lionel oilsparingly

Lubricate axle endswith Lionel oilsparingly



Lubricate axle endsat pocket locationswith Lionel oilsparingly

Lubricate axle endsat pocket locationswith Lionel oilsparingly

Lubricate with Lionel grease

Note: Lubricate side rods withLionel oil sparingly


17

Your Gold 700E Hudson is illuminated by a14-volt lamp located directly behind the

smoke box door. During the course of normaloperation, the lamp may require replacement.

Open the smoke box door to access the lamp.Remove the lamp from the smoke box door andreplace it with Lionel Part No. 610-8049-300and reinstall the lamp into the smoke box door.

Replacing your Gold 700E Hudson’s headlight

With typical use, your Gold700E Hudson will require

occasional lubrication of itsPullmor motor armature.

If you hear excess noiseduring operation, or if thelocomotive seems to slow downintermittently, you may need tooil the armature bearings.

Turn the Gold 700EHudson over and place it on asoft, protective surface.Remove the trailing truck

mounting stud and the ash panmounting screw.

Carefully unplug theinfra-red tether leads and

remove the trailing truckassembly. Apply a small

amount of oil (two drops) at thelocations indicated in the illus-tration. The armature should beoiled after every 20 hours ofoperation. Reposition the trail-ing truck assembly and reinstallthe screws.

Lubricating your Gold 700E Hudson’s Pullmor® motor armature

Press Aux2 to make sure headlamp was not accidently turned off, before replacing bulb

Your Lionel Hudson has firebox glow, this is a small bulb (Lionel part no.10-8056-009) located by the motor. During the course of normal operationit may require replacement. Because installation requires the soldering ofthe bulb to the motor, we recommend that you have your local AuthorizedLionel Service Center perform this service.

Note:

Use care when adding smoke fluid to prevent the fluid from dripping ontothe gold plated boiler. If this should happen, see page 19, “Caring for youGold 700E Hudson’s Appearance”.

18


Adding fluid to your Gold 700E Hudson’s smoke generator

Your Gold 700E Hudson is equipped witha smoke generator that produces safe,

clean white smoke during operation.The smoke generator requires the period-

ic addition of Lionel smoke fluid in order tofunction. Pierce the tube end witha pin, then add four to sixdrops of fluid directlyinto the Gold 700EHudson’s stack. Smoke produc-tion will commence momentarily, faster ifyou run your Gold 700E Hudson at speed.When smoke production wanes, add morefluid (four to eight drops).

An idle Gold 700E Hudson will notsmoke; press AUX1 and 9 (press for a maxi-mum of 10 seconds) to engage the smoke

generator at idle/in neutral. Always keep asmall amount of smoke fluid in the Gold700E Hudson’s smoke generator; the

generator’s element canbecome damaged if operated

without fluid. Smoke productionis greater at higher voltages and when

the Gold 700E Hudson is pulling a heavyload or long consist.

CAUTION:

If you have purchased the Lionel #6-17635 Gold Plated Caboose to complimentyour 700E Gold Hudson Engine and Tender, please refer to the above section

“Caring for your Gold 700E Hudson’s Appearance” for proper care of your caboose.

19


Caring for your Gold 700E Hudson’s Appearance

Included with your Gold 700E Hudson is ajeweler’s cloth and a pair of cotton gloves.

Extreme care must be taken when handlingyour Hudson to prevent any scratches ordamage to the gold or platinum plated sur-faces. The cotton gloves should be worn to

prevent fingerprints. Use the jeweler’s cloth,rubbing gently, to clean the gold and plat-inum plated surfaces of your Hudson. We donot recommend the use of any householdclothes or cleaning solutions.

Note!

Limited Warranty/Lionel Service

This Lionel product, including all mechanical andelectrical components, moving parts, motors and

structural components, except for light bulbs, is war-ranted to the original consumer-purchaser, for oneyear against original defects in materials or work-manship when purchased through an authorizedLionel dealer.

This warranty does NOT cover normal wearand tear, light bulbs, defects appearing in thecourse of commercial use, or damage resultingfrom abuse or misuse of the product by thepurchaser. Transfer of this product by the originalconsumer-purchaser to another person voids thiswarranty. Modification of this product voids thiswarranty.

Any warranted product which is defective inoriginal materials or workmanship and is deliveredby the original consumer-purchaser to Lionel L.L.C.or an authorized Lionel L.L.C. Service Station,together with proof of original purchase will, at theoption of Lionel L.L.C., be repaired or replaced,without charge for parts or labor. In the event thedefective product cannot be repaired, and areplacement is not available, a refund of theoriginal purchase price will be granted. Anyproducts on which warranty service is sought mustbe sent freight or postage prepaid, as transportationand shipping charges are not covered by thewarranty.

In no event shall Lionel L.L.C. beliable for incidental orconsequential damages.

Some states do not allow the exclusion orlimitation of incidental or consequential damages,so the above exclusion may not apply to you.

This limited warranty gives you specific legalrights, and you may have other rights which varyfrom state to state.

Instructions for Obtaining ServiceIf service for this Lionel L.L.C. product is

required, bring the item, along with your datedsales receipt and completed warranty information

to the nearest Authorized Lionel Service Station.Your nearest Lionel Service Station can be foundby calling 1-800-4-Lionel, or by accessing ourWebsite at www.lionel.com.

If you prefer to send your product back toLionel L.L.C. for factory repair, you must first call810-949-4100 or FAX 810-949-5429, or write toCustomer Service, P.O. Box 748, New Baltimore, MI48047-0748, stating what the item is, when it waspurchased and what seems to be the problem. Youwill be sent a return authorization letter and labelto ensure your merchandise will be properlyhandled upon receipt.

Once you have received your returnauthorization and label, make sure that the itemis packed to prevent damage during shipping andhandling. We suggest that you use the product’soriginal packaging. This shipment must beprepaid and we recommend that it be insured.

Please make sure you have followed all of theabove instructions carefully before returning anymerchandise for service.

Warranty InformationPlease complete the information below and

keep it, along with your dated sales receipt. Youmust present this and your dated sales receiptwhen requesting warranty service.

Name ____________________________

Address ____________________________

Place of Purchase ____________________

Date of Purchase ______________________

Product Number ______________________

Product Description ____________________

_ ________________________________

©2000 LIONEL LLC, CHESTERFIELD MI 48051-1956UNITED STATES OF AMERICA

Lionel 100 Anniversary 700E J-1E Hudson 4-6-4 … 8/00 featuring and Lionel 100 TH Anniversary 700E...

Documents

Transcript of Lionel 100 Anniversary 700E J-1E Hudson 4-6-4 … 8/00 featuring and Lionel 100 TH Anniversary 700E...