Linear Voltage Regulator Project
Transcript of Linear Voltage Regulator Project
![Page 1: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/1.jpg)
We started with an nMOS pass element but realized right away that this wasn't going to work properly.
DCOP when running nMOS pass element, notice that the output seen is 3 V
![Page 2: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/2.jpg)
DC Sweep with nMOS pass element; notice how the output starts from 2.4 V even when the input is 3.4V. Looking at this we knew that the reason because of this was that our pass element needed to be in the linear region at all times. In order to do so, we needed to use a pMOS pass element.
Schematic of Linear Voltage regulator with a one stage op amp and cMOS pass element with 3 mA load
![Page 3: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/3.jpg)
Schematic showing the DCOP of the Device. The output is more closer to 3 V
DC Sweep from 3.15 V to 7.5 V. The voltages shown are really close to 3 V.
![Page 4: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/4.jpg)
A zoomed out view of the DC sweep where one can not really see a difference in the voltage output graph (yellow).
AC analysis of one stage op amp showing that it is stable.
![Page 5: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/5.jpg)
After observing that our one stage op amp was working correctly and was stable we decided that it was time to implement our error amplifier as a a two stage opamp. We knew that an nMOS pass element would not work well so we used a pMOS pass element of the same width and length as in our one stage op amp. The width and length of the two stage op amp used was the same as the width and lengths used in our labs 6 and 7. The pass element width and length was chosen so that the device would stay in the triode/linear region of operation.
Schematic of overall ldo showing the 2 stageopamp as a symbol and using a PMOS device as a pass element
![Page 6: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/6.jpg)
schematic for checking stability of linear voltage regulator (LDO); notice how the negative feedback is broken so that the transfer function/bode plot can be analyzed from there
Graph showing the stability of our two stage opamp
![Page 7: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/7.jpg)
schematic showing specs of the PMOS pass element
schematic showing the PWL setup, as you can see in the voltage source labeled as VDD
![Page 8: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/8.jpg)
PWL analysis of Linear voltage regulator
schematic showing various loads, the one with that is the most stable is the one with longer range of ~3V input
![Page 9: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/9.jpg)
stability of the the 2 stage op amp
DC Sweep of LDO, notice how output (yellow) is around 3V for a large amount of range of inputs
![Page 10: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/10.jpg)
PWL of LDO, taking a step back, as you can see there is a little dip when voltage input changes; however the voltage output remains relatively around 4 pm.
![Page 11: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/11.jpg)
This is the same exact image as the first one except you are looking at each graph generated individually
![Page 12: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/12.jpg)
PWL with no load, not a large dip
![Page 13: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/13.jpg)
PWL with 3mA load; notice the large dip when changing the input voltage drastically
![Page 14: Linear Voltage Regulator Project](https://reader033.fdocuments.us/reader033/viewer/2022052214/550226ab4a7959c0558b4e91/html5/thumbnails/14.jpg)
References Rincon-Mora, Gabriel A. Analog IC Design with Low-dropout Regulators. New York: McGraw-
Hill, 2009.
G. A. Rincon-Mora and P. E. Allen, Study and design of low drop-out regulators, submitted to IEEE Trans. Circuits Syst.
B. Razavi, Design of CMOS Integrated Circuits, McGraw Hill, 2001 Jim Williams (March 1, 1989). "High Efficiency Linear Regulators" A.B. Grebene, Bipolar and MOS Analog Integrated Circuit Design, Wiley, New York, 1984.