Linde Electric Forklift Truck Joystick
-
Upload
runntech -
Category
Engineering
-
view
89 -
download
5
Transcript of Linde Electric Forklift Truck Joystick
RT-500 Industrial Joystick
Automatic spring return
Single axis, dual axis and 360° control
Modular design
Full sealed design
Adapt to any complex environment
RT-500 industrial joystick is mainly used in hydraulic proportional control construction machinery and variable frequency
motor control, such as Linde forklift truck.
Environment Parameter
Operating Temperature - 25°C ~ +80°C Protection Grade IP65 Vibration Amplitude±3g, Frequency 10Hz-200Hz Impact 20g, 6ms, Semi-sinusoidal
EMC Anti-interference Rank 100v/m,30MHz to 1GHz, 80% sine-wave modulation, meet EN50082-2 (1995) standard
EMC Emission Rank Rank B, 150KHz to 30MHz, meet EN50081-2 (1993) standard
ESD Anti-interference Rank Rank 4, 8KV contact discharge,15KV air discharge, meet the IEC61000-4-2 standard
Mechanical Parameter
Mechanical Angle ±32°(Potentiometer)±20°(Hall Sensor) Operating Torque 15N (50Nmax) Mechanical Life 5 million Mechanical Error ±0.5°
Electrical Parameter
Hall Power Supply Voltage 5±0.5V DC Power Supply Current Consumption 6.5mA/hall sensor
Key Features
Application
Technical Information
1 - 4 [email protected] | www.runntech.com
Resolution Ratio infinite Maximum Voltage 15VDC Reversed Polarity Maximum Voltage 14.5VDC Load Resistance 5KΩ Median Voltage (no-load) 48 - 52%Vs
Potentiometer
Power Supply Voltage DC24V Supply Current <20mA Resolution Ratio infinite Resistance (10%) 2KΩ, 5KΩ and 10KΩ Electrical Angle ±32° Output Voltage Range (relative voltage) 0 – 100%, 10 – 90% Median Voltage 48% - 52% Potentiometer Maximum Load Voltage 32VDC Maximum Power Consumption (25°C) 0.25W Switch Direction Switch Position ±3°
Selection Description ① Serial Number: RT-500
② Operation Form: T: automatic spring return
③ Operation Type: 1: single axis “—” , 2: dual axis cross control “+” , 3: 360° control
④ Electrical Output Form
Hall Output
HV1: DC 5V, 0 – 2.5 – 5V
HV2: DC 5V, 0.5 – 2.5 -4.5V
HV3: DC 5V, 1.0 – 2.5 – 4.0V
HV4: DC 5V, 1.25 - 2.5 – 3.75V
Potentiometer Output P1: Ordinary 2 directions output
P11: Double lines, 2 directions output
⑤ Potentiometer TypeCould choose 1k, 5k and 10k potentiometer, it also can be customized.
⑥ Quantity of Switch Signal01, 02 or 03, it also can be customized
Model RT-500 -□-□-□(□)-□(□)-□□
Selection ① ② ③ ④ ⑤ ⑥ ⑦ ⑧
Product Configuration
2 - 4 [email protected] | www.runntech.com
⑦ Common Closed Position
⑧ Remarks: remark from customers
Wiring Instruction
Potentiometer Output
1 6
2
3
4
5
Hall Voltage Output
1sw
a
1sw
b
2sw
a
2sw
b
5V 0 Xout
Yout
3sw
a
3sw
b
4sw
a
4sw
b
1 2 3 4 5 6 7 8 9 10
5sw
a
5sw
b
6sw
a
6sw
b
11 12 13 14 15 16 17 18 19 20
° ° ° °
3 - 4 [email protected] | www.runntech.com
Product Installation
4 - 4 [email protected] | www.runntech.com