Licensing

This feature module describes the licensing aspects of the Cisco ASR 901S Series Aggregation ServicesRouter.

• Finding Feature Information, page 1

• Feature Overview, page 2

• Licenses Supported on Cisco ASR 901S Router, page 2

• License Types, page 3

• Port or Interface Behavior, page 5

• Generating the License, page 11

• Installing the License , page 11

• Changing the License, page 13

• Verifying the License, page 13

• Where to Go Next, page 13

• Additional References, page 13

• Feature Information for Licensing, page 15

Finding Feature InformationYour software release may not support all the features documented in this module. For the latest featureinformation and caveats, see the release notes for your platform and software release. To find informationabout the features documented in this module, and to see a list of the releases in which each feature is supported,see the Feature Information for Licensing, on page 15.

Use Cisco Feature Navigator to find information about platform support and Cisco software image support.To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account on Cisco.com is notrequired.

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 1

Feature OverviewTheCisco ASR 901S router license is similar to any other software license in Cisco. It is tied to the UniqueDevice Identifier (UDI)—where the license is integrated to the PID (Product Identifier) and SN (SerialNumber). A license generated for one router cannot be shared or installed in any other router.

Complete these steps to obtain the license file:

1 Purchase the required Product Authorization Key (PAK).2 Get the UDI from the device.3 Enter the UDI and PAK in the Cisco’s licensing portal.

You will receive a license file through email.

1 Install the licenses on the device. For more information on how to install the license, see Installing theLicense , on page 11.

In addition to using the router CLI, you can install the license using the Cisco License Manager (CLM) or theCallhome interface.

Licenses Supported on Cisco ASR 901S RouterThe following licenses are supported:

License Type (Imageor Feature)

License DescriptionLicense PIDChassis PIDSl.No.

Image (by defaultgets enabled)

Base licenseSL-A901-BA901S-4SG-F-D

A901S-3SG-F-D

A901S-2SG-F-D

A901S-3SG-F-AH

A901S-2SG-F-AH

1

ImageAdvanced Metro IP license(includes all featuresprovided in the BaseLicense, plus advancedfeatures)

SL-A901-A=A901S-4SG-F-D

A901S-3SG-F-D

A901S-2SG-F-D

A901S-3SG-F-AH

A901S-2SG-F-AH

2

FeatureASR901 Timing FeatureLicense (1588 BoundaryClock [BC])

SL-A901-T=A901S-4SG-F-D

A901S-3SG-F-D

A901S-2SG-F-D

A901S-3SG-F-AH

A901S-2SG-F-AH

3

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide2 OL-30498-03

LicensingFeature Overview

The Cisco ASR 901S software uses the license description to resolve errors related to license availability.You need to map the proper license PID as per the table above and purchase the licenses.

The Cisco ASR 901S router supports only permanent licenses.

You should install only a supported license for the proper chassis PID. You will get a “Not Supported”messagewhile trying to install a wrong license. However, license installation process will go through and a confirmationmessage is displayed. When you run the show license command to display the details of this license, theoutput shows license state as “NOT IN USE”, and you cannot make it “IN USE”.The following is a sample confirmation message that is displayed on the router when you try to install a wronglicense.Router#lic instal flash:CAT1618U02C_201311132320280160.licInstalling licenses from "flash:CAT1618U02C_201311132320280160.lic"% Error: The device with UDI A901-4C-FT-D:CAT1618U02C not found0/3 licenses were successfully installed0/3 licenses were existing licenses3/3 licenses were failed to installRouter# 12:36 PMRouter#sh lic udiSlotID PID SN UDI--------------------------------------------------------------------------------*0 A901S-4SG-F-D FOC1738N74L A901S-4SG-F-D:FOC1738N74L

License TypesCisco ASR 901S router supports the following types of licenses:

• Image Level License

• Feature Based License

Image Level LicenseAn Image level license corresponds to the level of the IOS image that comes up based on the licenses presenton the router. This license is enforced while booting and it uses a universal image. It activates all the subsystemscorresponding to the license that you purchased. Image based licenses (SL-A901-B and SL-A901-A=) needrebooting of the router.

Features SupportedIn Cisco ASR 901S , Base license (SL-A901-B) and AdvancedMetroIPAccess (SL-A901-A) are permanent;once installed they do not expire. Trial or temporary licenses are not supported on the Cisco ASR 901S router.

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 3

LicensingLicense Types

FeaturesLicense

• L2, EVC, 802.1Q, 802.1ad, QinQ, 802.3ah,H-Qos, IPv4 static routes, routing protocols,host connectivity, ACL, REP, VRF-Lite

• E-OAM—CFM (BD, port level), IPSLA(barring LSP)

• Clocking—SyncE, 1588-OCSlave, 10M,G.781Priority based Clock Selection (no ESMC/SSM)

Time-division multiplexing (TDM) isunavailable.

Note

Base / SL-A901-B

• All IPBase license features

• MPLS—MPLS, L2VPN (EoMPLS), L3VPN,MPLS OAM, PW redundancy

• E-OAM—IPSLA(LSP)

AdvancedMetroIPAccess / SL-A901-A=

Feature Based LicenseThe feature based license is used to activate individual features when the image level licenses are used.

After the image level license is used and the appropriate subsystems are activated, individual feature licenseis used to activate individual features, which includes the ASR901 timing feature license (1588BC).

When installed, the ASR 901S timing feature license (1588 boundary clock) becomes active and there isno need to reboot the router.

Note

Port Based/Mode LicenseThe following table lists the port number, type, and the required license for those ports:

License PIDsChassis PIDPort TypePort Number

FLS-A901-4TA901-4C-FT-D

A901-4C-F-D

Copper0-3

No license is required.These ports are enabledby default.

Combo4-7

FLS-A901-4SA901-4C-FT-D

A901-4C-F-D

Small Form-FactorPluggable(SFP)

8-11

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide4 OL-30498-03

LicensingFeature Based License

License PIDsChassis PIDPort TypePort Number

FLS-A901-4A901-6CZ-FT-A

A901-6CZ-FT-D

A901-6CZ-F-A

A901-6CZ-F-D

Copper and SFP0-3 and 8-11

FLS-A901-2ZA901-6CZ-FT-A

A901-6CZ-FT-D

A901-6CZ-F-A

A901-6CZ-F-D

SFP+TenGig0/1, TenGig0/2

By default, ports 4 to 7 are enabled on the router. When you purchase the copper or SFP port license, thecorresponding ports are only enabled. Copper and SFP port licenses can co-exist.

1588BC License1588BC (SL-A901-T) license is a feature based license. This license does not need rebooting of the routerfor activation. The following table lists the features supported

FeaturesLicense PID

Clocking—1588V2 PTP boundary clockSL-A901-T

Port or Interface BehaviorThe following sections describe the port or interface behavior of the licenses:

Port Based LicenseWhen a port based license is not present, ports 4 to 7 are enabled. Ports 0 to 3, and ports 8 to 11 are disabled.This is the expected behavior. Interfaces that are disabled are in the administrative down state.

Example: When Port Based License is not InstalledThe following error message appears when the port based license is not installed and you use the no shutdowncommand on the interface:

Router# show ip interface brief

Interface IP-Address OK? Method Status ProtocolGigabitEthernet0/0 unassigned YES unset administratively down downGigabitEthernet0/1 unassigned YES unset administratively down downGigabitEthernet0/2 unassigned YES unset administratively down down

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 5

LicensingPort or Interface Behavior

GigabitEthernet0/3 unassigned YES unset administratively down downGigabitEthernet0/4 unassigned YES unset down downGigabitEthernet0/5 unassigned YES unset down downGigabitEthernet0/6 unassigned YES unset down downGigabitEthernet0/7 unassigned YES unset down downGigabitEthernet0/8 unassigned YES unset administratively down downGigabitEthernet0/9 unassigned YES unset administratively down downGigabitEthernet0/10 unassigned YES unset administratively down downGigabitEthernet0/11 unassigned YES unset administratively down downFastEthernet0/0 unassigned YES NVRAM administratively down downVlan1 unassigned YES unset down downRouter#Router(config-if)# interface gig 0/0Router(config-if)# no shutdown

Router(config-if)#*Oct 5 14:22:27.743: %LICENSE-1-REQUEST_FAILED: License request for feature fls-a901-4t1.0 failed. UDI=MWR-3941:FHAK13101A1

Router# show interface gigabitEthernet 0/0

GigabitEthernet0/0 is administratively down, line protocol is down (disabled).......reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA, loopback not setKeepalive set (10 sec)Full Duplex, 1000Mbps, link type is force-up, media type is RJ45output flow-control is unsupported, input flow-control is unsupportedLICENSE not available! Interface disabledARP type: ARPA, ARP Timeout 04:00:00Last input never, output never, output hang never

Example: When Port Based License is InstalledThe following example shows how to install the port based license:

Router# license install flash:FHAK13101A1_20110811190230024_fls-a901-4t.lic

Installing licenses from "flash:FHAK13101A1_20110811190230024_fls-a901-4t.lic"Installing...Feature:Fls-a901-4t...Successful:Supported1/1 licenses were successfully installed0/1 licenses were existing licenses0/1 licenses were failed to installRouter#*Oct 5 17:23:14.487: %LICENSE-6-INSTALL: Feature Fls-a901-4t 1.0 was installed inthis device. UDI=MWR-3941-TEST:FHAK13101A1; StoreIndex=2:Primary License StorageRouter(config)# interface gig 0/0Router(config-if)# no shutdown

When the port based license is installed for copper or SFP ports, the corresponding ports are enabled. Followingis a sample output from the show ip interface command:

Router# show ip interface brief

Interface IP-Address OK? Method Status ProtocolGigabitEthernet0/0 unassigned YES unset up upGigabitEthernet0/1 unassigned YES unset administratively down downGigabitEthernet0/2 unassigned YES unset administratively down down.....

Combo ports are either copper or SFP ports depending on the configuration specified in themedia-typecommand.

Note

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide6 OL-30498-03

LicensingPort Based License

10gigUpgrade LicenseWhen you do not have the 10gigUpgrade license, the 10 Gigabit Ethernet ports are enabled in 1 GigabitEthernet mode. Install the 10gigUpgrade license to enable new 10 Gigabit Ethernet ports in 10Gigabit Ethernetmode. To enable 1 Gigabit Ethernet mode, 1 Gigabit Ethernet SFPs have to be used on both the ends. Thereis no speed command to control the speed and this depends on the type of the SFP. The 10 Gigabit Ethernetports does not support 100M speed. You can connect 10 Gigabit Ethernet SFP+ to 10 Gigabit Ethernet portsonly.

Example: When 10gigUpgrade License is not InstalledThe following error message appears when the 10gigUpgrade license is not installed and you use the showinterface command:

Router# show interface Ten0/1

TenGigabitEthernet0/1 is down, line protocol is down (notconnect)Hardware is TenGigabit Ethernet, address is 2c54.2dd6.c10e (bia 2c54.2dd6.c10e)MTU 9216 bytes, BW 10000000 Kbit/sec, DLY 10 usec,

reliability 255/255, txload 1/255, rxload 1/255Encapsulation ARPA, loopback not setKeepalive set (10 sec)Unknown, Unknown, media type is H10GB-CU3Moutput flow-control is unsupported, input flow-control is unsupportedLICENSE not available or 1G SFP ( Interface in 1G mode )ARP type: ARPA, ARP Timeout 04:00:00Last input never, output never, output hang neverLast clearing of "show interface" counters neverInput queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0Queueing strategy: fifoOutput queue: 0/40 (size/max)5 minute input rate 0 bits/sec, 0 packets/sec5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no bufferReceived 0 broadcasts (0 multicasts)0 runts, 0 giants, 0 throttles0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored0 watchdog, 0 multicast, 0 pause input0 packets output, 0 bytes, 0 underruns0 output errors, 0 collisions, 0 interface resets0 unknown protocol drops0 babbles, 0 late collision, 0 deferred0 lost carrier, 0 no carrier, 0 pause output0 output buffer failures, 0 output buffers swapped out

Example: When 10gigUpgrade License is InstalledThe following example shows how to install the 10gigUpgrade license:

Router# license install flash:10G-ac.lic

Installing licenses from "flash:10G-ac.lic"Installing...Feature:10gigUpgrade...Successful:Supported1/1 licenses were successfully installed0/1 licenses were existing licenses0/1 licenses were failed to install

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 7

Licensing10gigUpgrade License

Following is a sample output from the show license command:

Router# show license

Index 1 Feature: AdvancedMetroIPAccessPeriod left: Life timeLicense Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: Medium

Index 2 Feature: IPBaseIndex 3 Feature: Gige4portflexiIndex 4 Feature: 10gigUpgrade

Period left: Life timeLicense Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: Medium

Flexi LicenseWhen a flexi license is not present, ports 4 to 7 are enabled. Ports 0 to 3, and ports 8 to 11 are disabled. Thisis the expected behavior. Interfaces that are disabled are in the administrative down state.

FLS-A901-4 flexi license is a combination of copper and SFP ports. This license is not tied to any port types.If you purchase a single FL-A901-4 license and install it, four ports are enabled and if you have two licenses,all the eight ports are enabled. You can purchase and install two flexi licenses in a router.

Flexi license is also called Count-based license, with a maximum count of two. In a normal license, if thelicense is already installed and when you try to install the same license again, the installation fails and routerdisplays Duplicate License error message. With flexi license (as it is count based), you can install the samelicense twice. Anything above this will throw an error.

Example: When Flexi License is not InstalledThe following error message appears when the flexi license is not installed and you use the show ip interfacecommand on the interface:

Router# show ip interface briefInterface IP-Address OK? Method Status ProtocolGigabitEthernet0/0 unassigned YES unset administratively down downGigabitEthernet0/1 unassigned YES unset administratively down downGigabitEthernet0/2 unassigned YES unset administratively down downGigabitEthernet0/3 unassigned YES unset administratively down downGigabitEthernet0/4 unassigned YES unset down downGigabitEthernet0/5 unassigned YES unset down downGigabitEthernet0/6 unassigned YES unset down downGigabitEthernet0/7 unassigned YES unset down downGigabitEthernet0/8 unassigned YES unset administratively down downGigabitEthernet0/9 unassigned YES unset administratively down downGigabitEthernet0/10 unassigned YES unset administratively down downGigabitEthernet0/11 unassigned YES unset administratively down downFastEthernet0/0 unassigned YES NVRAM administratively down downVlan1 unassigned YES unset down down

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide8 OL-30498-03

LicensingFlexi License

Example: When Flexi License is InstalledFollowing is a sample output from the show license command:

Router# show licenseIndex 1 Feature: AdvancedMetroIPAccess

Period left: Life timeLicense Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: Medium

Index 2 Feature: IPBaseIndex 3 Feature: Gige4portflexi Version: 1.0

License Type: PermanentLicense State: Active, Not In UseLicense Count: 2/0/0 (Active/In-use/Violation)License Priority: MediumStore Index: 1Store Name: Primary License Storage

1588BC LicenseWhen the SL-A901-T= 1588BC license is not installed, the PTP boundary clock cannot be configured. Formore information on configuring the PTP boundary clock, see PTP Boundary Clock.

Example: When 1588BC License is not InstalledThe following error message appears on configuring the PTP boundary clock, when the 1588BC license isnot installed:

Though an error message appears on configuring the PTP boundary clock, the running-config file acceptsthe PTP boundary clock configuration. This configuration can be saved. However, the PTP boundaryclock is not configured in the hardware, and is inactive.

Note

Router(config)# ptp clock boundary domain 0

%ERROR: Boundary Clock needs a separate license. Please install license and reconfigurePTP.Router(config-ptp-clk)#

Example: When 1588BC License is InstalledThe following example shows how to install the 1588BC license:

Router# license install flash:CAT1632U029_20121005013805577.lic

Installing licenses from "flash:CAT1632U029_20121005013805577.lic"Installing...Feature:1588BC...Successful:Supported1/1 licenses were successfully installed0/1 licenses were existing licenses0/1 licenses were failed to install

Following is a sample output from the show license command:

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 9

Licensing1588BC License

When the 1588BC license is installed and PTP boundary clock is not configured, the license state isdisplayed as Active, Not in Use . When the 1588BC license is installed and PTP boundary clock isconfigured, the license state is displayed as Active, In Use .

Note

Router# show license

Index 1 Feature: AdvancedMetroIPAccessIndex 2 Feature: IPBaseIndex 3 Feature: Gige4portflexiIndex 4 Feature: 10gigUpgradeIndex 5 Feature: 1588BC

Period left: Life timeLicense Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: Medium

Removing the LicenseIf PTP boundary clock is configured, then the following error message appears when removing the 1588BClicense:

Removing license is mainly used for development purpose.Note

Router# yesFeature: 1588BC

License Type: PermanentLicense State: Active, In UseLicense Addition: ExclusiveLicense Count: Non-CountedComment:Store Index: 2Store Name: Primary License Storage

Are you sure you want to clear? (yes/[no]): &;Handling Event, Unknown event type: 3% Error: Could not delete in-use licenseComplete the following steps to remove the license.

SUMMARY STEPS

1. Use the yes command to remove the PTP boundary clock configuration.2. Use the license clear command to remove the 1588BC license.

DETAILED STEPS

Step 1 Use the yes command to remove the PTP boundary clock configuration.Router(config-ptp-clk)# yes

Step 2 Use the license clear command to remove the 1588BC license.Router# yes

Feature: 1588BC

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide10 OL-30498-03

Licensing1588BC License

License Type: Permanent

License State: Active, Not in Use

License Addition: Exclusive

License Count: Non-Counted

Comment:

Store Index: 3

Store Name: Primary License Storage

Are you sure you want to clear? (yes/[no]): &;

Generating the LicenseComplete the following steps to generate the license:

SUMMARY STEPS

1. Use the show license udi command on the router2. Save the output.3. Go to the SWIFT tool at https://tools.cisco.com/SWIFT/Licensing/PrivateRegistrationServlet.4. Enter the PAK and UDI.5. Click Submit.

DETAILED STEPS

Step 1 Use the show license udi command on the routerStep 2 Save the output.

The output contains the UDI with the Product Identifier (PID) and Serial Number (SN).

Step 3 Go to the SWIFT tool at https://tools.cisco.com/SWIFT/Licensing/PrivateRegistrationServlet.Step 4 Enter the PAK and UDI.Step 5 Click Submit.

You will receive the license file through email.

Installing the LicenseComplete the following steps to install the license:

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 11

LicensingGenerating the License

SUMMARY STEPS

1. enable2. license install ?3. copy tftp: flash:4. show flash:5. license install &;6. reload

DETAILED STEPS

PurposeCommand or Action

Enables the privileged EXEC mode.enableStep 1

Example:

Router> enable

• Enter your password if prompted.

(Optional) License can be installed either by placing the licensefile in the tftp boot directory or by copying the license to the flash:directory.

license install ?

Example:

Router# license install ?

Step 2

Copies the license file to the flash: directory.copy tftp: flash:

Example:

Router# copy tftp: flash:

Step 3

Displays the contents of the flash: directory.show flash:

Example:

Router# show flash:

Step 4

Installs the license from the flash: directory.license install &;

Example:

Router# license installFHK10LLL021_20110530015634482.lic

Step 5

Reboots the system to activate the new license.reloadStep 6

Example:

Router# reload

The license is activated after installation. Rebooting therouter is required only for AdvancedMetroIPAccess.

Note

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide12 OL-30498-03

LicensingInstalling the License

Changing the LicenseThe license boot level command is used only to select the required image-based licensing. For the Cisco ASR901S Series Routers, only one image based license (AdvancedMetroIPAccess) is available. Installing thislicense and reloading the router takes care of this license. If the license install does not work properly, use thelicense boot level command for AdvancedMetroIPAccess in the global configuration mode, to change thelicense and reboot the system to activate the new license.

If you do not install a license, the router starts with the lowest level license by default.Note

After installing the AdvancedMetroIPAccess license and reloading the router, the AdvancedMetroIPAccesslicense will be activated by default.

Note

Verifying the LicenseTo verify the new license, use the show license command.

Router# show licenseIndex 1 Feature: AdvancedMetroIPAccess

Period left: LifetimeLicense Type: PermanentLicense State: Active, In UseLicense Priority: HighLicense Count: 1/1/0 (Active/In-use/Violation)

Index 2 Feature:.....Period left: 0 minute 0 second

Where to Go NextFor additional information on Licensing, see the documentation listed in the Additional References section.

Additional ReferencesRelated Documents

Document TitleRelated Topic

Cisco IOS Master Commands List, All ReleasesCisco IOS commands

Cisco ASR 901S Series Aggregation Services RouterCommand Reference

Cisco ASR 901S Command Reference

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 13

LicensingChanging the License

Document TitleRelated Topic

Cisco IOS Interface and Hardware ComponentCommand Reference

Cisco IOS Interface and Hardware ComponentCommands

Cisco IOS Software Activation Conceptual OverviewCisco Software Licensing Concepts

Cisco ASR 901S Series Aggregation Services RouterSoftware Configuration Guide

Cisco ASR 901S Software Configuration Guide

Standards

TitleStandard

—None

MIBs

MIBs LinkMIB

To locate and downloadMIBs for selected platforms,Cisco software releases, and feature sets, use CiscoMIB Locator found at the following URL:

http://www.cisco.com/go/mibs

None

RFCs

TitleRFC

No new or modified RFCs are supported by thisfeature, and support for existing RFCs has not beenmodified by this feature.

Technical Assistance

LinkDescription

http://www.cisco.com/cisco/web/support/index.htmlThe Cisco Support and Documentation websiteprovides online resources to download documentation,software, and tools. Use these resources to install andconfigure the software and to troubleshoot and resolvetechnical issues with Cisco products and technologies.Access to most tools on the Cisco Support andDocumentation website requires a Cisco.com user IDand password.

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide14 OL-30498-03

LicensingAdditional References

Feature Information for LicensingThe following table lists the release history for this feature and provides links to specific configurationinformation.

Use Cisco Feature Navigator to find information about platform support and software image support. CiscoFeature Navigator enables you to determine which software images support a specific software release, featureset, or platform. To access Cisco Feature Navigator, go to http://www.cisco.com/go/cfn . An account onCisco.com is not required.

The following table lists only the software release that introduced support for a given feature in a givensoftware release train. Unless noted otherwise, subsequent releases of that software release train alsosupport that feature.

Note

Table 1: Feature Information for Licensing

Feature InformationReleasesFeature Name

The following sections provideinformation about this feature:

• Licenses Supported on CiscoASR 901S Router, on page2

• License Types, on page 3

• Port or Interface Behavior,on page 5

• Generating the License, onpage 11

• Installing the License , onpage 11

• Changing the License, onpage 13

• Return MaterialsAuthorization LicenseProcess

15.2(2)SNH1Licensing

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide OL-30498-03 15

LicensingFeature Information for Licensing

Feature InformationReleasesFeature Name

The following sections provideinformation about this feature:

• Licenses Supported on CiscoASR 901S Router, on page2

• License Types, on page 3

• Port or Interface Behavior,on page 5

15.2(2)SNI1588BC Licensing

New PIDs were added to thedocument.

15.4(2)SLicensing

Cisco ASR 901S Series Aggregation Services Router Software Configuration Guide16 OL-30498-03

LicensingFeature Information for Licensing