Lecture 17 position systems of nc [compatibility mode]
-
Upload
muftooh-ur-rehman-siddiqi -
Category
Technology
-
view
466 -
download
8
description
Transcript of Lecture 17 position systems of nc [compatibility mode]
![Page 1: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/1.jpg)
Lecture By: Muftooh Ur Rehman Siddiqi
ME-418 CAD/CAM
Lecture #: 17
Position Control System of NC
Ref: Groover (Chap – 06)
Faculty of Mechanical Engineering
Ghulam Ishaq Khan Institute of Engineering Sciences & Technology, Pakistan.
Lecture By: Muftooh Ur Rehman SiddiqiResearch Associate
Office # G-17Email: [email protected]
![Page 2: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/2.jpg)
NC Positioning SystemsNC Positioning Systems
• The NC positioning system converts the coordinates axis valuesin the NC part program into relative positions of the tool andworkpart during processing.
• The worktable moves linearly by means of a rotating leadscrewwhich is driven by a stepping motor or servomotor.
• The leadscrew has a certain pitch p (in/thread, mm/thread).The table moves a distance of p at every rotation of the lead
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 2 of 11
The table moves a distance of p at every rotation of the leadscrew.
Figure shows a typical motor and lead screw arrangement in NC positing system
![Page 3: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/3.jpg)
NC Positioning SystemsNC Positioning Systems
There are two types of positioning systems used in NCsystems
(a) Open loop system
(b) Closed loop control
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 3 of 11
![Page 4: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/4.jpg)
Open Loop systemOpen Loop systemOperates without verifying that the actual positionachieved in the move, is the same as the desired position.
Open loop systems cost less than the closed loop systemsand are appropriate when the force resisting the actualmotion is minimal.
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 4 of 11
![Page 5: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/5.jpg)
Closed Loop ControlClosed Loop Control
Uses a feedback measurements to confirm that the finalposition of the worktable is the location specified in theprogram
Normally specified for machines that perform continuouspath operations such as milling or turning, in which thereare significant forces resisting the forward motion of the
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 5 of 11
are significant forces resisting the forward motion of thecutting tool.
![Page 6: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/6.jpg)
Closed Loop Control Closed Loop Control –– Optical EncoderOptical EncoderFrequency of the pulse is computed to determine the position and velocity of worktable.
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 6 of 11
![Page 7: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/7.jpg)
Engineering Analysis of NC positioning SystemsEngineering Analysis of NC positioning Systems
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 7 of 11
![Page 8: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/8.jpg)
Engineering Analysis of NC positioning SystemsEngineering Analysis of NC positioning Systems
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 8 of 11
![Page 9: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/9.jpg)
Precision in NC PositioningPrecision in NC Positioning
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 9 of 11
![Page 10: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/10.jpg)
Assignment
Solve the following problems from Groover Chapter 6
Submission date 12nd Dec 2011.
Open loop
24, 25, 26, 27
Closed Loop
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 10 of 11
Closed Loop
29, 31, 32, 34, 36
Resolution and Accuracy
38, 39, 40, 41
Batch Production, 8th Dec 2011.
![Page 11: Lecture 17 position systems of nc [compatibility mode]](https://reader034.fdocuments.us/reader034/viewer/2022042700/558fd0111a28ab3f1b8b4647/html5/thumbnails/11.jpg)
Thank you…
© Muftooh Ur Rehman Siddiqi, FME GIK Institute, Pakistan. 11 of 11
Thank you…