lECEx Certificate IECI* of Conformity - R. STAHL · 2021. 1. 7. · IECI* lECEx Certificate of...
Transcript of lECEx Certificate IECI* of Conformity - R. STAHL · 2021. 1. 7. · IECI* lECEx Certificate of...
-
IECI* lECEx Certificateof ConformityINTERNATIONAL ELECTROTECHNICAL COMMISSION
IEC Certification Scheme for Explosive Atmospheresfor rules and details of the lECEx Scheme visit www.iecex.com
Ex COMPONENT CERTIFICATE
Certificate No.: lECEx BVS 08.0039U
Status: Current
Dateoflssue: 2018-11-28
Issue No: 2 Certificate history:Issue No. 2(2018-11-28)
Page 1 of 5 Issue No. 1 (2011-07-08) Issue No. 0(2008-08-13)
Applicant: R. STAHL Schaltgeräte GmbHAm Bahnhof 30 74638 Waldenburg Germany
Ex Component: Motor protection circuit-breaker type 8523/8.-..-...
This component is NOT intended to be used alone and requires additional consideration when incorporated into other equipment or Systems for use in explosive atmospheres (refer to IEC 60079-0).
Type of Protection: Equipment protection by flameproof enclosures "d", Equipment protection by increased safety "e"
Marking:Ex db eb MC Gb Ex db eb I Mb
Approved for issue on behalf of the lECEx Jörg KochCertification Body:
Position:
Signature:(for printed Version)
Date:
Head of Certification Body
1
1. This certificate and schedule may only be reproduced in full.2. This certificate is not transferable and remains the property of the issuing body.3. The Status and authenticity of this certificate may be verified by visiting the Official lECEx Website.
Certificate issued by:
DEKRA EXAM GmbH Dinnendahlstrasse 9
44809 Bochum Germany
> DEKRAOn the $afe side.
http://www.iecex.com
-
Certificate No: lECEx BVS 08.0039U Issue No: 2
Dateoflssue: 2018-11-28 Page 2 of 5
Manufacturer: R. STAHL Schaltgeräte GmbHAm Bahnhof 30 74638 Waldenburg Germany
Additional Manufacturing location(s):
This certificate is issued as verification that a sample(s), representative of production, was assessed and tested and found to comply with the IEC Standard list below and that the manufacturer's quality System, relating to the Ex Component covered by this certificate, was assessed and found to comply with the lECEx Quality System requirements. This certificate is granted subject to the conditions as set out in lECEx Scheme Rules, lECEx 02 and Operational Documents as amended.
STANDARDS:The Ex Component and any acceptable variations to it specified in the schedule of this certificate and the identified documents, was found to comply with the following Standards:
IEC 60079-0:2017Edition:7.0
IEC 60079-1 :2014-06 Edition:7.0
IEC 60079-7:2017Edition:5.1
This Certificate does not indicate compliance with eiectricai safety and performance requirements other than those expressiy included in the
Standards listed above.
TEST & ASSESSMENT REPORTS:A sample(s) ofthe Ex Component listed has successfutty met the examination and fest requirements as recorded in
Test Report:
DE/BVS/ExTR08.0044/01
Quality Assessment Report:
DE/BVS/QAR10.0002/14
lECEx Certificateof Conformity
Explosive atmospheres - Part 0: Equipment - General requirements
Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
Explosive atmospheres - Part 7: Equipment protection by increased safety "e"
IECI*
-
lECEx Certificate of Conformity
Certificate No: lECEx BVS 08.0039U
Dateoflssue: 2018-11-28
Schedule
Ex Component(s) covered by this certificate is described below:
Subject and type
See Annex
Description
The motor protection circuit-breaker type 8523/8.-..-... is designed in type of protection flameproof enclosure "d" for the enclosure and in type of protection increased safety “e” for the connection terminals. It is used for the protection and switching of explosion protected electrical motors. The motor protection circuit-breaker is intended for installation into enclosures in type of protection increased safety “e” which are certified separately.
SCHEDULE OF LIMITATIONS:
After the installation of the motor protection circuit-breaker into an enclosure in type of protection increased safety "e", the clearances and creepage distances have to meet the requirements of 4.3 (fable 2) and 4.4 (fable 2) of IEC 60079-7.
Issue No: 2
Page 3 of 5
ffl
-
IECI®lECEx Certificate
of ConformityCertificate No: lECEx BVS 08.0039U
Dateoflssue: 2018-11-28
DETAILS OF CERTIFICATE CHANGES (for issues 1 and above):
Updating of the Standards
Issue No: 2
Page 4 of 5
-
Issue No: 2
Page 5 of 5
lECEx Certificateof Conformity
2 Conductor sizes of the main contacts
Rated Connection cross section
Minimum connection cross section
Conductor sizes of the auxiliary contacts
Conductor sizes of the auxiliary contacts
Minimum connection cross section
3 Maximum permissible enclosure temperature
of the motor protection Circuit breaker 100 °C
Annex:
BVS_08_0039U_R.Stahl_lssue2_Annex.pdf
2.5 mm2
0.75 mm2
10 mm2
1.5 mm2
Certificate No: lECEx BVS 08.0039U
Date of Issue: 2018-11-28
Additional Information:
Parameters
1 Rated voltage up to AC 690 V
Rated current of main contacts up to 25 A
Rated current of auxiliary contacts up to 6 A
IECI®