Lava Heat Italia - Pandora Portable Fire Cabinet - Owners Manual

8/12/2019 Lava Heat Italia - Pandora Portable Fire Cabinet - Owners Manual

1/15


2/15

TABLE OF CONTENTS

Caution . 1

Exploding drawing-Y7 . 2

Parts list-Y7. ..3

Assembly Procedures ..4

Position logs and glass ball on the burner 5

Heater Stand and Location 6

Gas Requirements ..6

Leakage Test 6

Lighting instructions 7

Storage . .. 7

Cleaning and Care ..7

Data badge1.8

Data badge2.9

Problems Check List ..10


3/15

CAUTIONPLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION

FOR INSTALLATION, PLEASE READ THIS MANUAL CAREFULLY REPAIRS SHOULD BE DONE BY A QUALIFIED SERVICE PERSON ONLY

Do not use this appliance for indoors, as it may cause personal injury or propertydamage.This outdoor heater is not intended to be installed on recreational vehicles and/orboats.

Appliance should be located on a solid surface.Maintenance and repair should be carried out by a qualified person.Improper installation, adjustment, alteration can cause personal injury or propertydamage.Do not attempt to alter the unit in any manner.Never replace or substitute the regulator with any regulator other than thefactory-suggested replacement.Do not store or use gasoline or other flammable vapors or liquids in the heater unit.The whole gas system, hose, regulator, pilot or burner should be inspected for leaksor damage before use, and at least annually by a qualified service person.

All leak tests should be done with a soap solution. Never use an open flame to checkfor leaks.Do not use the heater until all connections have been leak tested.Turn off the gas valve immediately if smell of gas is detected.Do not transport heater while it is operating.Do not move the heater after it has been turned off until the temperature has cooleddown..Control compartment, burner and circulation air passageways of the heater must bekept clean.Frequent cleaning may be required as necessary.The LP tank should be turned off when the heater is not in use.Check the heater immediately if any of the following occurs:- The heater does not reach temperature.- The burner makes popping noise during use (a slight noise is normal when the

burner is extinguished).- Smell of gas in conjunction with extreme yellow tipping of the burner flames.

The LPG regulator/hose assembly must be located in the tank cabinet where LPGtank located

Any guard or other protective device removed for servicing the heater must bereplaced before operating the heater.

Adults and children should stay away from high temperature surface to avoid burns orclothing ignition.Children should be carefully supervised when they are in the area of the heater.Clothing or other flammable materials should not be hung on the heater or placed onor near the heater.

1


4/15

Exploding Drawing-Y7

2


5/15

Parts List-Y7

3

Part No Part Name Qty Part No Part Name Qty

1 Side panel of bottom cupboard 2 21 Inner panel of burner 1

2 Wheel without brake 2 22 Artificial log set 1

3 Wheel with brake 2 23 Outer top connection 1

4 Bottom panel 1 24 Inner top connection 1

5 Back door of bottom cupboard 1 25 Back handle 1

6 Door knob 2 26 Top mash side connection 2

7 Side supporter of combustion

chamber bottom panel

2 27 Top panel 1

8 Bottom door damper 1 28 Pilot protector 1

9 Turn knob bracket 1 29 Top mesh 1

10 Turn knob 1 30 Top panel of combustion chamber 1

11 Outer middle decorated bar 1 31 Side tempered glass 2

12 Gas valve 1 32 Glass slot 1

13 Inner middle decorated bar 1 33 Front tempered glass 1

14 Inner piece 2 34 Pilot 1

15 Inner panel of Top back door 1 35 Pilot bracket 1

16 Outer panel of Top back door 1 36 Front supporter of combustion

chamber bottom panel

1

17 Hinge 1 37 Bottom of combustion chamber 1

18 Back vertical bar 2 38 Front panel of bottom cupboard 1

19 Branket of burner 2 39 Decorated oblate glass ball

20 Outer panel of burner 1


6/15

ASSEMBLY PROCEDURESTake out the heater body and all of the parts from carton, then follow below procedures.

STEP 1 STEP 2

Screw the knob on tank door with screw

we supplied in one set.

Use 2 pcs of M8 screw to contact handrail

with heater body

STEP 3 STEP 4 if go with back wheel

Screw four wheels on heater body, twowheel without brake for front side and two

for behind.

Position top space mesh on the top board,then screw it on.

4


7/15

Position ceramic logs on the burner

!"#$%&" Y7

1 Take out ceramic logs decorated oblate glass ball from carton2 Refer to following picture for position the ceramic logs and

decorated oblate glass ball.

` 5


8/15

HEATER STAND AND LOCATION

The heater is for outdoor use only. Always ensure that adequatefresh air ventilation is provided.

Always maintain proper clearance to combustible materials.Heater must be placed on level firm ground.Never operate heater in an explosive atmosphere like in areas wheregasoline or other flammable liquids or vapors are stored.Keep a distance of at least 2 metres from Combustible Materials.

After every use, turn off the gas valve on the cylinder.The heater should be protected from strong winds by braking the wheel

GAS REQUIREMENTS

Use liquid propane gas only.The pressure regulator and hose assembly to be used must conform to local standardcodes.The installation must conform to local codes, or in the absence of local codes, withthe standard for the storage and handling of liquid petroleum gases.

A dented, rusted or damaged propane tank may be hazardous and should bechecked by your tank supplier. Never use a propane tank with a damaged valveconnection.The propane tank must be arranged to provide for vapor withdrawal from theoperating cylinder.Never connect an unregulated propane tank to the heater.

LEAKAGE TEST

Gas connections on the heater are leak tested at the factory prior to shipment. A completegas tightness check must be performed at the installation site due to possible mishandlingin shipment or excessive pressure being applied to the heater.

Make a soap solution of one part liquid detergent and one part water. The soapsolution can be applied with a spray bottle, brush or rag. Soap bubbles will appear incase of a leak.The heater must be checked with a full cylinder.Make sure the safety control valve is in the OFF position.Turn the gas supply ON.In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gassupply on and recheck.Never do leak test while smoking.

6


9/15

LIGHTING INSTRUCTIONS Open the cabinet door, put the gas cylinder into the cabinetTurn the control knob clockwise to OFF position.Connect the regulator to the gas bottle. Turn the gas supply ON at the cylinder.Check with the use of soapy water for any gas leakage between the bottle and theregulatorPush down the control knob and keep pressing whilst turning anti-clockwise to theIgnition position (a click will be heard), this will light the pilot. If not repeat thisprocess.When the pilot burner is lit, keep the control knob pressed for 5 seconds then releaseit.If the burner does not stay alight, repeat steps 3 and 4. If the burner has not lit wait 5minutes and repeat steps 3 and 4.

Adjust the heat setting by turning the control knob to the high or low position.To turn the heater OFF turn the cylinder valve or regulator switch to the OFFposition and then turn the control knob on the appliance clockwise to the OFFposition.

WARNING:If the burner fails to ignite, turn the control knob off (clockwise) and also turn the cylindervalve off. Wait five minutes before attempting to relight with ignition sequence.

CLEANING AND CAREMake sure all the cleaning is done after turn off the heater and cooling down.Wipe off powder coated surfaces with soft, moist rag.Do not clean heater with cleaners that are combustible or corrosive.Remove debris from the burner to keep it clean and safe for use.Open the top back door to clean debris on glass carefully.

STORAGE1. Always close the gas valve of the gas cylinder after use or in case of a disturbance.2. Remove the pressure controller and the hose.3. Check the tightness of the gas valve and for damage. If you suspect a damage, have itchanged by your gas dealer.4. Never store liquid gas cylinder in a sub-terrain, or at places without adequate airventilation

7


10/15

DATA BADGE FOR THE Y7 MOBILE PATIO HEATER

APPLIANCE CODE: Y7

TOTAL HEAT INPUT: BTUGAS CATEGORIES: I 3+ I3B/P(30) TYPES OF GAS: Butane Propane LPG mixturesGAS PRESSURE: 28 30 mbar butane

37 mbar propane30 mbar LPG mixtures

INJECTOR SIZE: 1.45 mm 1.45 mmFOR USE OUTDOORS AND IN WELL VENTILATED AREASTHIS APPLIANCE IS NOT FOR DOMESTIC USEWARNING: ACCESSIBLE PARTS MAY BE VERY HOT. KEEP YOUNG CHILDRENAWAYREAD THE INSTRUCTION LITERATURE BEFORE USING THE APPLIANCE. THEAPPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THEINSTRUCTIONS AND LOCAL REGULATIONSCLOSE THE VALVE OF THE GAS CYLINDER OR THE REGULATOR AFTER USE.THE USE OF THIS APPLIANCE IN ENCLOSED AREAS CAN BE DANGEROUSAND IS PROHIBITEDWELL VENTILATED AREAS MUST HAVE A MINIMUM OF 25% OF THE SURFACEAREA OPEN. THE SURFACE AREA IS THE SUM OF THE WALL SURFACE.

8


11/15

DATA BADGE FOR THE Y7 MOBILE PATIO HEATER

APPLIANCE CODE: Y7

TOTAL HEAT INPUT: 61000BTUGAS CATEGORIES: I 3B/P(50) TYPES OF GAS: LPG mixturesGAS PRESSURE: 50 mbar LPG mixturesINJECTOR SIZE: 1.30 mmFOR USE OUTDOORS AND IN WELL VENTILATED AREASTHIS APPLIANCE IS NOT FOR DOMESTIC USEWARNING: ACCESSIBLE PARTS MAY BE VERY HOT. KEEP YOUNG CHILDRENAWAYREAD THE INSTRUCTION LITERATURE BEFORE USING THE APPLIANCE. THEAPPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THEINSTRUCTIONS AND LOCAL REGULATIONSCLOSE THE VALVE OF THE GAS CYLINDER OR THE REGULATOR AFTER USE.THE USE OF THIS APPLIANCE IN ENCLOSED AREAS CAN BE DANGEROUSAND IS PROHIBITEDWELL VENTILATED AREAS MUST HAVE A MINIMUM OF 25% OF THE SURFACEAREA OPEN. THE SURFACE AREA IS THE SUM OF THE WALL SURFACE.

9


12/15

10


13/15


14/15


15/15

Lava Heat Italia - Pandora Portable Fire Cabinet - Owners Manual

Documents

Transcript of Lava Heat Italia - Pandora Portable Fire Cabinet - Owners Manual