lab07

32
ELEC 101 Lab 7

description

 

Transcript of lab07

ELEC 101

Lab 7

31 July 2003 ELEC 101 Lab 7 2

Lab 7 Schematic Symbols

31 July 2003 ELEC 101 Lab 7 3

Lab 7 Schematic Symbols

31 July 2003 ELEC 101 Lab 7 4

Lab 7A Schematic Symbols

NOTE: When entering ground, make sure you give it the name 0 or you will receive and error message when you run the simulation.

31 July 2003 ELEC 101 Lab 7 5

Lab 7 PARAM/SPECIAL Part

31 July 2003 ELEC 101 Lab 7 6

Lab 7A Schematic

31 July 2003 ELEC 101 Lab 7 7

Lab 7A Simulation Settings

31 July 2003 ELEC 101 Lab 7 8

Lab 7A Output

31 July 2003 ELEC 101 Lab 7 9

Lab 7B Schematic

31 July 2003 ELEC 101 Lab 7 10

Lab 7B Y Axis Settings

31 July 2003 ELEC 101 Lab 7 11

Lab 7B Output

31 July 2003 ELEC 101 Lab 7 12

Lab 7C Schematic

31 July 2003 ELEC 101 Lab 7 13

To Configure RVAL •  DCL on Parameters •  CL on New Column •  From the Dialog Box specify the Name and Value

as shown in the following graphic •  CL on Apply

31 July 2003 ELEC 101 Lab 7 14

DCL on PARAMETERS

31 July 2003 ELEC 101 Lab 7 15

Lab 7C RVAL Properties

31 July 2003 ELEC 101 Lab 7 16

To Configure RVAL •  The RVAL column was created and selected as

shown in the previous graphic. The exact location of the new column may be in a different position.

•  CL on the Display Button •  CL on the Name and Value Button as shown in the

next graphic •  Close the window

31 July 2003 ELEC 101 Lab 7 17

Set PARAM Display Properites

31 July 2003 ELEC 101 Lab 7 18

LAB 07C - Create a DC Sweep •  Create a New Simulation Profile called lab07c •  Create the same DC Sweep as used for lab07a •  CL and place a check in Parametric Sweep •  CL in the Global Parameter Option button •  Enter the Parameter name: RVAL •  CL in the Value List Option button •  In the Value List enter the space delimited values

100 200 300 (there is only one space between the three values)

•  CL on OK

31 July 2003 ELEC 101 Lab 7 19

Lab 7C RVAL Sweep Settings

31 July 2003 ELEC 101 Lab 7 20

Lab 7C Output Available Sections

Leave all the list values are selected If you wanted to select one or more of the profiles, Hold CTRL and CL to select or deselect a specific multiple profiles

31 July 2003 ELEC 101 Lab 7 21

Lab 7C Output

31 July 2003 ELEC 101 Lab 7 22

Lab 7D Schematic

31 July 2003 ELEC 101 Lab 7 23

Lab 7D Output

Lab 7

Output for Submission

31 July 2003 ELEC 101 Lab 7 25

Lab 7A Schematic

31 July 2003 ELEC 101 Lab 7 26

Lab 7A Output

31 July 2003 ELEC 101 Lab 7 27

Lab 7B Schematic

31 July 2003 ELEC 101 Lab 7 28

Lab 7B Output

31 July 2003 ELEC 101 Lab 7 29

Lab 7C Schematic

31 July 2003 ELEC 101 Lab 7 30

Lab 7C Output

31 July 2003 ELEC 101 Lab 7 31

Lab 7D Schematic

31 July 2003 ELEC 101 Lab 7 32

Lab 7D Output