Lab Number 1 Lab Results Ratings Average PopStdDev Z Score · 2018-02-20 · Lab Results Ratings...
Transcript of Lab Number 1 Lab Results Ratings Average PopStdDev Z Score · 2018-02-20 · Lab Results Ratings...
2017 Fine Aggregate Round Robin Report
Lab Number 1
100.0
97.3
Total Percent Passing the #4 Sieve
65.5
39.4
22.6Total Percent Passing the #50 Sieve
10.8
6.47
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.47
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.97
0.09
0.43
-0.47
-0.10
0.65
0.24
0.42
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 2
100.0
97.1
Total Percent Passing the #4 Sieve
67.3
40.3
21.5Total Percent Passing the #50 Sieve
10.7
6.14
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.55
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.02
0.09
0.06
0.31
0.31
0.09
0.18
0.23
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 3
100.0
98.0
Total Percent Passing the #4 Sieve
68.0
43.0
23.0Total Percent Passing the #50 Sieve
11.0
6.50
5
3
5
3
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.10
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.59
0.09
1.73
0.62
1.52
0.85
0.35
0.44
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 4
100.0
96.7
Total Percent Passing the #4 Sieve
68.3
40.6
23.0Total Percent Passing the #50 Sieve
11.9
6.80
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.81
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.74
0.09
-0.69
0.75
0.44
0.85
0.88
0.61
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 5
100.0
96.8
Total Percent Passing the #4 Sieve
62.5
36.2
19.6Total Percent Passing the #50 Sieve
6.3
0.80
5
5
3
3
5
2
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.48
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.05
0.09
-0.50
-1.78
-1.54
-0.87
-2.41
-2.81
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 8
100.0
97.3
Total Percent Passing the #4 Sieve
68.4
40.7
22.0Total Percent Passing the #50 Sieve
11.0
6.50
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.78
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.26
0.09
0.43
0.80
0.49
0.34
0.35
0.44
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 9
100.0
96.7
Total Percent Passing the #4 Sieve
64.1
38.5
20.5Total Percent Passing the #50 Sieve
10.0
5.70
5
5
4
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
3Percent Loss by T11 (P200 Wash) 3.60
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.98
0.09
-0.69
-1.08
-0.50
-0.41
-0.23
-0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 10
100.0
96.7
Total Percent Passing the #4 Sieve
66.9
41.4
22.6Total Percent Passing the #50 Sieve
11.8
11.46
5
5
5
5
5
5
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 11.40
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
6.03
0.09
-0.69
0.14
0.80
0.65
0.82
3.26
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 12
100.0
97.4
Total Percent Passing the #4 Sieve
62.5
35.1
18.3Total Percent Passing the #50 Sieve
10.3
6.07
5
5
3
2
3
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.23
0.09
0.61
-1.78
-2.03
-1.52
-0.06
0.19
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 14
100.0
96.7
Total Percent Passing the #4 Sieve
65.5
38.8
21.4Total Percent Passing the #50 Sieve
10.6
5.90
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
2Percent Loss by T11 (P200 Wash) 3.49
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-2.09
0.09
-0.69
-0.47
-0.37
0.04
0.12
0.10
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 16
100.0
96.1
Total Percent Passing the #4 Sieve
64.6
38.8
20.9Total Percent Passing the #50 Sieve
10.7
6.08
5
3
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.35
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.18
0.09
-1.80
-0.86
-0.37
-0.21
0.18
0.20
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 17
100.0
96.6
Total Percent Passing the #4 Sieve
66.2
40.3
22.7Total Percent Passing the #50 Sieve
11.4
6.17
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.07
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.56
0.09
-0.87
-0.17
0.31
0.70
0.59
0.25
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 18
100.0
98.9
Total Percent Passing the #4 Sieve
82.1
67.7
58.9Total Percent Passing the #50 Sieve
54.0
51.28
5
0
0
0
0
0
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 51.01
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
46.89
0.10
3.39
6.78
12.65
18.98
25.65
25.88
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 19
0.0
97.5
Total Percent Passing the #4 Sieve
68.4
42.2
23.1Total Percent Passing the #50 Sieve
10.4
4.85
0
5
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
1Percent Loss by T11 (P200 Wash) 2.77
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-2.83
-476.10
0.80
0.80
1.16
0.90
0.00
-0.50
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 20
100.0
96.1
Total Percent Passing the #4 Sieve
65.9
40.2
22.5Total Percent Passing the #50 Sieve
11.5
6.71
5
3
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.24
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.73
0.09
-1.80
-0.30
0.26
0.59
0.65
0.56
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 22
100.0
97.2
Total Percent Passing the #4 Sieve
64.9
38.1
20.7Total Percent Passing the #50 Sieve
10.9
6.37
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.94
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.42
0.09
0.24
-0.73
-0.68
-0.31
0.30
0.36
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 23
100.0
97.2
Total Percent Passing the #4 Sieve
67.0
40.5
22.7Total Percent Passing the #50 Sieve
11.3
6.43
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.85
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.33
0.09
0.24
0.18
0.40
0.70
0.53
0.40
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 24
100.0
98.4
Total Percent Passing the #4 Sieve
67.5
41.3
22.3Total Percent Passing the #50 Sieve
11.3
6.36
5
2
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.23
0.09
2.47
0.40
0.76
0.49
0.53
0.36
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 28
100.0
97.1
Total Percent Passing the #4 Sieve
66.0
39.3
20.8Total Percent Passing the #50 Sieve
11.2
6.03
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.49
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.04
0.09
0.06
-0.25
-0.14
-0.26
0.47
0.17
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 29
100.0
97.0
Total Percent Passing the #4 Sieve
68.0
40.0
20.0Total Percent Passing the #50 Sieve
6.0
0.30
5
5
5
5
5
1
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
3Percent Loss by T11 (P200 Wash) 7.04
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
1.55
0.09
-0.13
0.62
0.17
-0.67
-2.58
-3.10
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 31
100.0
97.4
Total Percent Passing the #4 Sieve
67.6
41.6
23.2Total Percent Passing the #50 Sieve
11.3
6.40
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.00
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.49
0.09
0.61
0.45
0.89
0.95
0.53
0.38
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 32
100.0
97.1
Total Percent Passing the #4 Sieve
66.8
40.3
21.5Total Percent Passing the #50 Sieve
10.8
6.37
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.82
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.30
0.09
0.06
0.10
0.31
0.09
0.24
0.36
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 33
100.0
97.6
Total Percent Passing the #4 Sieve
68.6
43.3
23.7Total Percent Passing the #50 Sieve
12.6
7.04
5
5
5
3
4
4
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.28
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.77
0.09
0.99
0.88
1.66
1.20
1.29
0.75
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 34
100.0
98.2
Total Percent Passing the #4 Sieve
68.6
41.2
23.4Total Percent Passing the #50 Sieve
11.5
6.48
5
2
5
5
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.23
0.09
2.10
0.88
0.71
1.05
0.65
0.43
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 35
0.0
97.8
Total Percent Passing the #4 Sieve
67.6
41.0
22.1Total Percent Passing the #50 Sieve
10.7
5.90
0
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.40
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.13
-476.10
1.36
0.45
0.62
0.39
0.18
0.10
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 36
0.0
97.7
Total Percent Passing the #4 Sieve
67.1
40.2
21.4Total Percent Passing the #50 Sieve
10.8
6.20
0
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.55
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.02
-476.10
1.17
0.23
0.26
0.04
0.24
0.27
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 37
100.0
97.3
Total Percent Passing the #4 Sieve
66.3
39.0
20.9Total Percent Passing the #50 Sieve
10.3
5.85
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.35
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.18
0.09
0.43
-0.12
-0.28
-0.21
-0.06
0.07
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 39
100.0
96.4
Total Percent Passing the #4 Sieve
64.2
36.7
18.4Total Percent Passing the #50 Sieve
9.2
5.25
5
4
4
4
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.99
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.55
0.09
-1.24
-1.04
-1.31
-1.47
-0.70
-0.27
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 40
100.0
97.1
Total Percent Passing the #4 Sieve
68.7
42.7
23.1Total Percent Passing the #50 Sieve
12.3
7.06
5
5
5
4
5
4
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.69
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.17
0.09
0.06
0.93
1.39
0.90
1.12
0.76
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 41
100.0
97.4
Total Percent Passing the #4 Sieve
67.6
38.3
20.9Total Percent Passing the #50 Sieve
10.0
5.63
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.16
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.38
0.09
0.61
0.45
-0.59
-0.21
-0.23
-0.06
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 42
100.0
97.5
Total Percent Passing the #4 Sieve
65.2
37.5
19.9Total Percent Passing the #50 Sieve
9.4
5.37
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.76
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.79
0.09
0.80
-0.60
-0.95
-0.72
-0.59
-0.21
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 43
100.0
95.5
Total Percent Passing the #4 Sieve
63.1
35.6
15.9Total Percent Passing the #50 Sieve
4.8
0.20
5
1
3
3
1
0
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
3Percent Loss by T11 (P200 Wash) 3.70
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.88
0.09
-2.92
-1.52
-1.81
-2.73
-3.29
-3.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 45
100.0
96.5
Total Percent Passing the #4 Sieve
63.6
36.8
19.5Total Percent Passing the #50 Sieve
9.8
5.70
5
4
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.96
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.58
0.09
-1.06
-1.30
-1.27
-0.92
-0.35
-0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 46
100.0
97.3
Total Percent Passing the #4 Sieve
66.3
39.4
21.9Total Percent Passing the #50 Sieve
10.9
6.15
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 31.21
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
26.47
0.09
0.43
-0.12
-0.10
0.29
0.30
0.24
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 47
100.0
97.4
Total Percent Passing the #4 Sieve
65.6
38.4
20.6Total Percent Passing the #50 Sieve
10.4
5.90
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.26
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.27
0.09
0.61
-0.43
-0.55
-0.36
0.00
0.10
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 48
100.0
98.1
Total Percent Passing the #4 Sieve
68.4
42.3
23.0Total Percent Passing the #50 Sieve
11.7
6.73
5
3
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.96
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.44
0.09
1.91
0.80
1.21
0.85
0.77
0.57
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 50
100.0
97.0
Total Percent Passing the #4 Sieve
64.7
38.2
20.8Total Percent Passing the #50 Sieve
10.8
5.30
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.23
0.09
-0.13
-0.82
-0.64
-0.26
0.24
-0.25
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 51
100.0
97.2
Total Percent Passing the #4 Sieve
66.9
40.1
21.6Total Percent Passing the #50 Sieve
10.6
6.10
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.35
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.18
0.09
0.24
0.14
0.22
0.14
0.12
0.21
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 52
100.0
97.0
Total Percent Passing the #4 Sieve
65.8
38.1
20.2Total Percent Passing the #50 Sieve
9.9
6.00
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.75
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.23
0.09
-0.13
-0.34
-0.68
-0.57
-0.29
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 53
100.0
96.7
Total Percent Passing the #4 Sieve
64.5
36.7
19.4Total Percent Passing the #50 Sieve
9.7
5.99
5
5
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.69
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.17
0.09
-0.69
-0.91
-1.31
-0.97
-0.41
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 54
100.0
98.0
Total Percent Passing the #4 Sieve
70.4
44.1
24.2Total Percent Passing the #50 Sieve
11.5
6.54
5
3
3
2
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.01
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.50
0.09
1.73
1.67
2.02
1.45
0.65
0.46
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 55
0.0
2.6
Total Percent Passing the #4 Sieve
31.1
28.4
20.8Total Percent Passing the #50 Sieve
11.5
5.00
0
0
0
0
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.79
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.27
-476.10
-174.94
15.49
5.05
0.26
0.65
-0.42
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 57
100.0
97.3
Total Percent Passing the #4 Sieve
66.5
40.8
22.0Total Percent Passing the #50 Sieve
10.8
5.74
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.29
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.24
0.09
0.43
-0.03
0.53
0.34
0.24
0.00
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 58
100.0
97.0
Total Percent Passing the #4 Sieve
67.1
40.7
22.6Total Percent Passing the #50 Sieve
11.2
6.18
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.45
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.08
0.09
-0.13
0.23
0.49
0.65
0.47
0.26
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 59
100.0
98.2
Total Percent Passing the #4 Sieve
65.0
37.5
20.1Total Percent Passing the #50 Sieve
10.4
6.37
5
2
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.71
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.19
0.09
2.10
-0.69
-0.95
-0.62
0.00
0.36
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 60
100.0
97.2
Total Percent Passing the #4 Sieve
69.6
43.4
24.3Total Percent Passing the #50 Sieve
12.1
7.23
5
5
4
3
3
4
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 6.72
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
1.22
0.09
0.24
1.32
1.70
1.50
1.00
0.85
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 61
100.0
97.7
Total Percent Passing the #4 Sieve
67.0
38.9
20.7Total Percent Passing the #50 Sieve
10.5
5.80
5
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
1Percent Loss by T11 (P200 Wash) 2.97
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-2.63
0.09
1.17
0.18
-0.32
-0.31
0.06
0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 63
100.0
97.0
Total Percent Passing the #4 Sieve
67.0
38.1
17.7Total Percent Passing the #50 Sieve
5.6
0.20
5
5
5
5
3
1
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.17
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.66
0.09
-0.13
0.18
-0.68
-1.83
-2.82
-3.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 64
100.0
95.9
Total Percent Passing the #4 Sieve
62.8
34.8
15.7Total Percent Passing the #50 Sieve
5.1
0.41
5
2
3
2
1
0
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.71
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.84
0.09
-2.17
-1.65
-2.17
-2.84
-3.11
-3.03
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 66
100.0
97.9
Total Percent Passing the #4 Sieve
68.5
41.7
22.6Total Percent Passing the #50 Sieve
11.5
6.55
5
3
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.19
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.68
0.09
1.54
0.84
0.94
0.65
0.65
0.47
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 67
100.0
96.6
Total Percent Passing the #4 Sieve
65.6
38.4
21.3Total Percent Passing the #50 Sieve
10.9
6.34
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.93
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.41
0.09
-0.87
-0.43
-0.55
-0.01
0.30
0.35
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 69
100.0
97.1
Total Percent Passing the #4 Sieve
65.8
38.0
19.6Total Percent Passing the #50 Sieve
9.6
5.85
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.70
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.18
0.09
0.06
-0.34
-0.73
-0.87
-0.47
0.07
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 70
100.0
97.5
Total Percent Passing the #4 Sieve
67.8
39.2
20.7Total Percent Passing the #50 Sieve
9.4
5.30
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.41
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.15
0.09
0.80
0.53
-0.19
-0.31
-0.59
-0.25
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 72
100.0
97.0
Total Percent Passing the #4 Sieve
68.4
41.4
22.5Total Percent Passing the #50 Sieve
11.1
6.34
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.82
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.30
0.09
-0.13
0.80
0.80
0.59
0.41
0.35
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 73
100.0
97.3
Total Percent Passing the #4 Sieve
66.4
39.3
20.8Total Percent Passing the #50 Sieve
10.0
5.64
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
1Percent Loss by T11 (P200 Wash) 2.91
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-2.69
0.09
0.43
-0.08
-0.14
-0.26
-0.23
-0.05
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 74
100.0
96.4
Total Percent Passing the #4 Sieve
67.1
39.9
21.6Total Percent Passing the #50 Sieve
10.8
6.70
5
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.90
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.38
0.09
-1.24
0.23
0.13
0.14
0.24
0.55
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 75
100.0
97.0
Total Percent Passing the #4 Sieve
68.0
42.0
24.0Total Percent Passing the #50 Sieve
15.0
10.00
5
5
5
4
4
1
2
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.00
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.54
0.09
-0.13
0.62
1.07
1.35
2.71
2.43
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 76
100.0
97.2
Total Percent Passing the #4 Sieve
64.3
35.1
18.9Total Percent Passing the #50 Sieve
9.9
5.88
5
5
5
2
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 0.13
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-5.57
0.09
0.24
-1.00
-2.03
-1.22
-0.29
0.08
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 77
100.0
96.7
Total Percent Passing the #4 Sieve
65.8
38.8
18.2Total Percent Passing the #50 Sieve
5.9
0.70
5
5
5
5
3
1
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 6.52
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
1.02
0.09
-0.69
-0.34
-0.37
-1.57
-2.64
-2.87
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 78
100.0
96.9
Total Percent Passing the #4 Sieve
66.4
40.4
22.2Total Percent Passing the #50 Sieve
11.4
6.69
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.39
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.89
0.09
-0.31
-0.08
0.35
0.44
0.59
0.55
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 79
100.0
97.0
Total Percent Passing the #4 Sieve
62.4
36.3
18.4Total Percent Passing the #50 Sieve
8.6
4.89
5
5
3
4
4
4
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.80
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.75
0.09
-0.13
-1.83
-1.49
-1.47
-1.06
-0.48
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 80
99.9
95.9
Total Percent Passing the #4 Sieve
63.8
37.2
19.9Total Percent Passing the #50 Sieve
9.6
5.58
5
2
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.73
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.82
-0.38
-2.17
-1.21
-1.09
-0.72
-0.47
-0.09
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 81
100.0
97.4
Total Percent Passing the #4 Sieve
67.9
40.0
21.2Total Percent Passing the #50 Sieve
10.2
5.68
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.68
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.16
0.09
0.61
0.58
0.17
-0.06
-0.12
-0.03
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 82
100.0
97.2
Total Percent Passing the #4 Sieve
65.5
38.8
21.1Total Percent Passing the #50 Sieve
10.3
5.65
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.15
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.39
0.09
0.24
-0.47
-0.37
-0.11
-0.06
-0.05
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 83
100.0
97.5
Total Percent Passing the #4 Sieve
68.4
42.7
24.2Total Percent Passing the #50 Sieve
12.0
6.78
5
5
5
4
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.38
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.88
0.09
0.80
0.80
1.39
1.45
0.94
0.60
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 84
100.0
96.4
Total Percent Passing the #4 Sieve
65.7
39.4
21.3Total Percent Passing the #50 Sieve
10.4
5.76
5
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.80
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.75
0.09
-1.24
-0.38
-0.10
-0.01
0.00
0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 86
100.0
97.1
Total Percent Passing the #4 Sieve
64.1
36.3
18.1Total Percent Passing the #50 Sieve
6.7
2.10
5
5
4
4
3
2
2
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.09
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.48
0.09
0.06
-1.08
-1.49
-1.63
-2.17
-2.07
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 87
100.0
97.6
Total Percent Passing the #4 Sieve
66.7
38.5
21.2Total Percent Passing the #50 Sieve
10.8
6.70
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.18
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.67
0.09
0.99
0.05
-0.50
-0.06
0.24
0.55
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 88
100.0
97.3
Total Percent Passing the #4 Sieve
65.9
38.9
22.0Total Percent Passing the #50 Sieve
11.3
6.80
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.07
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.56
0.09
0.43
-0.30
-0.32
0.34
0.53
0.61
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 89
100.0
96.2
Total Percent Passing the #4 Sieve
66.0
37.7
20.7Total Percent Passing the #50 Sieve
11.3
7.50
5
3
5
5
5
5
4
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.60
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.07
0.09
-1.62
-0.25
-0.86
-0.31
0.53
1.01
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 90
0.0
97.8
Total Percent Passing the #4 Sieve
69.1
42.7
23.3Total Percent Passing the #50 Sieve
11.4
5.76
0
4
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.76
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.24
-476.10
1.36
1.10
1.39
1.00
0.59
0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 91
100.0
96.8
Total Percent Passing the #4 Sieve
68.4
41.2
22.3Total Percent Passing the #50 Sieve
10.8
5.80
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
2Percent Loss by T11 (P200 Wash) 3.47
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-2.11
0.09
-0.50
0.80
0.71
0.49
0.24
0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 92
100.0
97.2
Total Percent Passing the #4 Sieve
66.2
39.5
22.7Total Percent Passing the #50 Sieve
12.6
8.00
5
5
5
5
5
4
4
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
2Percent Loss by T11 (P200 Wash) 7.77
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
2.30
0.09
0.24
-0.17
-0.05
0.70
1.29
1.29
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 94
100.0
97.7
Total Percent Passing the #4 Sieve
67.6
41.2
23.5Total Percent Passing the #50 Sieve
11.3
6.57
5
4
5
5
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.76
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.24
0.09
1.17
0.45
0.71
1.10
0.53
0.48
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 95
99.9
97.2
Total Percent Passing the #4 Sieve
66.9
39.1
21.1Total Percent Passing the #50 Sieve
10.3
6.12
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.26
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.27
-0.38
0.24
0.14
-0.23
-0.11
-0.06
0.22
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 98
100.0
96.8
Total Percent Passing the #4 Sieve
63.4
36.6
19.6Total Percent Passing the #50 Sieve
9.7
5.60
5
5
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.60
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.07
0.09
-0.50
-1.39
-1.36
-0.87
-0.41
-0.08
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 99
100.0
97.1
Total Percent Passing the #4 Sieve
65.4
38.4
20.2Total Percent Passing the #50 Sieve
10.3
6.00
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.59
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.06
0.09
0.06
-0.52
-0.55
-0.57
-0.06
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 100
100.0
97.8
Total Percent Passing the #4 Sieve
69.3
43.5
23.6Total Percent Passing the #50 Sieve
11.8
6.34
5
4
4
3
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.70
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.18
0.09
1.36
1.19
1.75
1.15
0.82
0.35
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 102
100.0
96.8
Total Percent Passing the #4 Sieve
67.1
39.7
21.6Total Percent Passing the #50 Sieve
10.3
5.64
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.05
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.49
0.09
-0.50
0.23
0.04
0.14
-0.06
-0.05
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 105
100.0
97.1
Total Percent Passing the #4 Sieve
65.8
38.7
20.7Total Percent Passing the #50 Sieve
9.8
5.76
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.26
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.27
0.09
0.06
-0.34
-0.41
-0.31
-0.35
0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 106
100.0
96.6
Total Percent Passing the #4 Sieve
64.5
37.5
19.5Total Percent Passing the #50 Sieve
9.5
5.20
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.16
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.38
0.09
-0.87
-0.91
-0.95
-0.92
-0.53
-0.30
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 107
100.0
97.0
Total Percent Passing the #4 Sieve
67.0
39.0
19.0Total Percent Passing the #50 Sieve
7.0
1.60
5
5
5
5
4
3
2
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.22
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.32
0.09
-0.13
0.18
-0.28
-1.17
-2.00
-2.35
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 108
100.0
96.8
Total Percent Passing the #4 Sieve
66.8
40.4
20.9Total Percent Passing the #50 Sieve
8.3
4.91
5
5
5
5
5
4
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.91
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.63
0.09
-0.50
0.10
0.35
-0.21
-1.23
-0.47
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 109
100.0
96.8
Total Percent Passing the #4 Sieve
66.5
41.1
21.9Total Percent Passing the #50 Sieve
11.0
6.62
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.07
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.56
0.09
-0.50
-0.03
0.67
0.29
0.35
0.51
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 110
100.0
96.8
Total Percent Passing the #4 Sieve
67.1
40.0
21.8Total Percent Passing the #50 Sieve
10.3
5.81
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.71
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.19
0.09
-0.50
0.23
0.17
0.24
-0.06
0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 111
100.0
97.0
Total Percent Passing the #4 Sieve
68.0
41.2
22.7Total Percent Passing the #50 Sieve
11.9
7.10
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.37
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.87
0.10
-0.13
0.62
0.71
0.70
0.88
0.78
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 112
100.0
97.0
Total Percent Passing the #4 Sieve
67.8
41.0
22.6Total Percent Passing the #50 Sieve
11.4
6.60
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.91
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.39
0.09
-0.13
0.53
0.62
0.65
0.59
0.49
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 113
100.0
97.7
Total Percent Passing the #4 Sieve
70.0
43.6
24.1Total Percent Passing the #50 Sieve
11.7
6.30
5
4
4
3
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.67
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.15
0.09
1.17
1.49
1.79
1.40
0.77
0.32
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 115
100.0
97.3
Total Percent Passing the #4 Sieve
66.4
37.7
19.5Total Percent Passing the #50 Sieve
8.8
4.90
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.44
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.12
0.09
0.43
-0.08
-0.86
-0.92
-0.94
-0.47
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 116
100.0
97.1
Total Percent Passing the #4 Sieve
66.1
38.4
19.7Total Percent Passing the #50 Sieve
9.8
5.56
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.86
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.69
0.09
0.06
-0.21
-0.55
-0.82
-0.35
-0.10
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 117
100.0
97.0
Total Percent Passing the #4 Sieve
67.8
40.6
22.6Total Percent Passing the #50 Sieve
10.4
5.70
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.23
0.09
-0.13
0.53
0.44
0.65
0.00
-0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 118
100.0
2.9
Total Percent Passing the #4 Sieve
33.4
27.2
17.2Total Percent Passing the #50 Sieve
9.0
4.00
5
0
0
0
2
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 30.70
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
25.95
0.09
-174.39
-14.49
-5.59
-2.08
-0.82
-0.99
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 119
100.0
97.1
Total Percent Passing the #4 Sieve
66.0
39.7
21.1Total Percent Passing the #50 Sieve
10.4
6.10
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.84
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.32
0.09
0.06
-0.25
0.04
-0.11
0.00
0.21
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 120
100.0
97.4
Total Percent Passing the #4 Sieve
68.9
42.7
23.3Total Percent Passing the #50 Sieve
11.8
6.66
5
5
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.76
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.24
0.09
0.61
1.01
1.39
1.00
0.82
0.53
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 121
0.0
97.0
Total Percent Passing the #4 Sieve
63.0
36.0
18.0Total Percent Passing the #50 Sieve
8.0
4.00
0
5
3
3
3
4
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 1.90
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-3.73
-476.10
-0.13
-1.56
-1.63
-1.68
-1.41
-0.99
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 122
100.0
97.3
Total Percent Passing the #4 Sieve
69.3
41.9
22.7Total Percent Passing the #50 Sieve
11.3
6.80
5
5
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.79
0.09
0.43
1.19
1.03
0.70
0.53
0.61
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 123
100.0
97.2
Total Percent Passing the #4 Sieve
65.6
37.5
19.5Total Percent Passing the #50 Sieve
9.9
5.60
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.28
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.28
0.09
0.24
-0.43
-0.95
-0.92
-0.29
-0.08
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 124
100.0
96.5
Total Percent Passing the #4 Sieve
65.6
40.3
21.7Total Percent Passing the #50 Sieve
11.3
6.50
5
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.73
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.21
0.09
-1.06
-0.43
0.31
0.19
0.53
0.44
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 125
100.0
97.0
Total Percent Passing the #4 Sieve
66.0
40.2
22.5Total Percent Passing the #50 Sieve
10.9
6.19
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.66
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.14
0.09
-0.13
-0.25
0.26
0.59
0.30
0.26
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 127
100.0
97.9
Total Percent Passing the #4 Sieve
68.8
42.2
22.4Total Percent Passing the #50 Sieve
10.6
5.70
5
3
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.35
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.21
0.09
1.54
0.97
1.16
0.54
0.12
-0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 128
100.0
97.7
Total Percent Passing the #4 Sieve
68.7
41.9
23.4Total Percent Passing the #50 Sieve
11.3
6.09
5
4
5
4
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.51
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.02
0.09
1.17
0.93
1.03
1.05
0.53
0.20
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 130
100.0
97.4
Total Percent Passing the #4 Sieve
65.4
35.1
16.4Total Percent Passing the #50 Sieve
5.4
1.03
5
5
5
2
2
1
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 32.46
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
27.76
0.09
0.61
-0.52
-2.03
-2.48
-2.94
-2.68
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 131
100.0
97.0
Total Percent Passing the #4 Sieve
65.6
38.2
20.8Total Percent Passing the #50 Sieve
10.2
5.80
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.20
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.34
0.09
-0.13
-0.43
-0.64
-0.26
-0.12
0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 132
100.0
97.4
Total Percent Passing the #4 Sieve
65.4
37.5
19.7Total Percent Passing the #50 Sieve
9.7
5.80
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.50
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.03
0.09
0.61
-0.52
-0.95
-0.82
-0.41
0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 133
100.0
97.9
Total Percent Passing the #4 Sieve
66.9
41.5
22.6Total Percent Passing the #50 Sieve
11.5
6.70
5
3
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.20
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.69
0.09
1.54
0.14
0.85
0.65
0.65
0.55
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 136
100.0
96.9
Total Percent Passing the #4 Sieve
64.3
35.2
18.2Total Percent Passing the #50 Sieve
8.9
5.20
5
5
5
3
3
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.44
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.12
0.09
-0.31
-1.00
-1.99
-1.57
-0.88
-0.30
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 137
100.0
97.4
Total Percent Passing the #4 Sieve
67.4
39.3
30.0Total Percent Passing the #50 Sieve
11.0
6.40
5
5
5
5
0
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.79
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.27
0.09
0.61
0.36
-0.14
4.38
0.35
0.38
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 138
100.0
96.5
Total Percent Passing the #4 Sieve
67.2
40.9
22.3Total Percent Passing the #50 Sieve
11.4
6.00
5
4
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.24
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.30
0.09
-1.06
0.27
0.58
0.49
0.59
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 139
100.0
95.7
Total Percent Passing the #4 Sieve
63.2
37.8
21.1Total Percent Passing the #50 Sieve
11.3
6.00
5
1
4
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.99
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.47
0.09
-2.54
-1.48
-0.82
-0.11
0.53
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 140
0.0
15.5
Total Percent Passing the #4 Sieve
161.9
161.3
94.5Total Percent Passing the #50 Sieve
60.8
27.00
0
0
0
0
0
0
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.79
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.27
-476.10
-151.06
-41.62
-54.81
-36.96
-29.65
-12.09
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 141
100.0
96.6
Total Percent Passing the #4 Sieve
65.4
37.3
20.5Total Percent Passing the #50 Sieve
10.2
6.00
5
5
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.67
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.15
0.09
-0.87
-0.52
-1.04
-0.41
-0.12
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 142
100.0
97.0
Total Percent Passing the #4 Sieve
67.3
40.0
22.3Total Percent Passing the #50 Sieve
11.3
6.16
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.85
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.33
0.09
-0.13
0.31
0.17
0.49
0.53
0.24
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 143
100.0
96.8
Total Percent Passing the #4 Sieve
60.4
32.1
15.2Total Percent Passing the #50 Sieve
5.3
0.99
5
5
1
0
0
1
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.80
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.75
0.09
-0.50
-2.70
-3.38
-3.09
-3.00
-2.70
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 144
100.0
96.7
Total Percent Passing the #4 Sieve
67.7
42.6
22.9Total Percent Passing the #50 Sieve
11.9
6.60
5
5
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.40
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.90
0.09
-0.69
0.49
1.34
0.80
0.88
0.49
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 145
100.0
97.2
Total Percent Passing the #4 Sieve
67.5
41.5
21.9Total Percent Passing the #50 Sieve
11.0
6.12
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.07
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.56
0.09
0.24
0.40
0.85
0.29
0.35
0.22
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 146
100.0
96.8
Total Percent Passing the #4 Sieve
66.7
41.4
22.4Total Percent Passing the #50 Sieve
10.9
6.22
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.90
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.64
0.09
-0.50
0.05
0.80
0.54
0.30
0.28
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 147
100.0
96.3
Total Percent Passing the #4 Sieve
64.1
38.1
20.8Total Percent Passing the #50 Sieve
11.1
6.54
5
4
4
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.02
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.52
0.09
-1.43
-1.08
-0.68
-0.26
0.41
0.46
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 148
100.0
97.0
Total Percent Passing the #4 Sieve
68.0
42.0
22.0Total Percent Passing the #50 Sieve
11.0
6.30
5
5
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.65
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.13
0.09
-0.13
0.62
1.07
0.34
0.35
0.32
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 149
100.0
96.8
Total Percent Passing the #4 Sieve
64.2
37.0
19.5Total Percent Passing the #50 Sieve
9.8
5.77
5
5
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.97
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.57
0.09
-0.50
-1.04
-1.18
-0.92
-0.35
0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 150
100.0
97.5
Total Percent Passing the #4 Sieve
67.9
41.0
23.0Total Percent Passing the #50 Sieve
11.6
6.50
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.41
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.91
0.09
0.80
0.58
0.62
0.85
0.71
0.44
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 152
100.0
97.2
Total Percent Passing the #4 Sieve
69.1
38.5
19.9Total Percent Passing the #50 Sieve
9.8
5.66
5
5
4
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 4.55
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-1.00
0.09
0.24
1.10
-0.50
-0.72
-0.35
-0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 153
100.0
97.7
Total Percent Passing the #4 Sieve
68.9
42.8
23.0Total Percent Passing the #50 Sieve
11.7
6.30
5
4
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.11
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.60
0.09
1.17
1.01
1.43
0.85
0.77
0.32
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 154
100.0
95.0
Total Percent Passing the #4 Sieve
62.0
35.0
16.0Total Percent Passing the #50 Sieve
5.4
0.60
5
0
2
2
1
1
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.30
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.23
0.09
-3.85
-2.00
-2.08
-2.68
-2.94
-2.92
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 156
100.0
97.1
Total Percent Passing the #4 Sieve
68.7
43.2
22.9Total Percent Passing the #50 Sieve
11.3
6.31
5
5
5
3
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.14
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.63
0.09
0.06
0.93
1.61
0.80
0.53
0.33
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 157
100.0
95.6
Total Percent Passing the #4 Sieve
63.8
36.8
19.8Total Percent Passing the #50 Sieve
9.9
5.70
5
1
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.84
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.71
0.09
-2.73
-1.21
-1.27
-0.77
-0.29
-0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 158
100.0
96.8
Total Percent Passing the #4 Sieve
65.7
39.7
21.6Total Percent Passing the #50 Sieve
11.2
6.25
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.55
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.02
0.09
-0.50
-0.38
0.04
0.14
0.47
0.30
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 159
100.0
97.1
Total Percent Passing the #4 Sieve
65.7
37.3
19.8Total Percent Passing the #50 Sieve
9.9
5.70
5
5
5
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.26
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.27
0.09
0.06
-0.38
-1.04
-0.77
-0.29
-0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 160
100.0
97.0
Total Percent Passing the #4 Sieve
66.0
39.0
21.0Total Percent Passing the #50 Sieve
10.4
6.00
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.40
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.13
0.09
-0.13
-0.25
-0.28
-0.16
0.00
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 161
100.0
97.5
Total Percent Passing the #4 Sieve
69.0
41.1
22.3Total Percent Passing the #50 Sieve
11.2
6.00
5
5
4
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.66
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.14
0.09
0.80
1.06
0.67
0.49
0.47
0.15
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 162
97.4
67.3
Total Percent Passing the #4 Sieve
39.4
21.2
10.6Total Percent Passing the #50 Sieve
6.0
5.76
0
0
0
0
0
1
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.74
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.22
-12.22
-55.13
11.87
8.30
5.41
-2.58
0.02
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 164
100.0
97.0
Total Percent Passing the #4 Sieve
64.2
36.0
19.4Total Percent Passing the #50 Sieve
9.8
5.40
5
5
4
3
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.09
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.45
0.09
-0.13
-1.04
-1.63
-0.97
-0.35
-0.19
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 165
100.0
96.7
Total Percent Passing the #4 Sieve
65.6
40.9
22.6Total Percent Passing the #50 Sieve
12.0
7.01
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
4Percent Loss by T11 (P200 Wash) 6.90
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
1.41
0.09
-0.69
-0.43
0.58
0.65
0.94
0.73
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 166
100.0
96.7
Total Percent Passing the #4 Sieve
66.8
39.0
21.3Total Percent Passing the #50 Sieve
11.0
6.30
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.85
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.33
0.09
-0.69
0.10
-0.28
-0.01
0.35
0.32
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 169
100.0
96.4
Total Percent Passing the #4 Sieve
63.5
37.1
19.6Total Percent Passing the #50 Sieve
10.2
5.90
5
4
4
4
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.48
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.05
0.09
-1.24
-1.35
-1.13
-0.87
-0.12
0.10
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 170
100.0
69.9
Total Percent Passing the #4 Sieve
65.9
37.2
17.8Total Percent Passing the #50 Sieve
6.1
0.90
5
0
5
4
3
1
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.50
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.03
0.09
-50.31
-0.30
-1.09
-1.78
-2.53
-2.75
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 172
100.0
97.3
Total Percent Passing the #4 Sieve
64.4
38.4
20.4Total Percent Passing the #50 Sieve
10.5
6.09
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.50
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.03
0.09
0.43
-0.95
-0.55
-0.46
0.06
0.20
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 173
100.0
97.6
Total Percent Passing the #4 Sieve
66.2
38.3
20.9Total Percent Passing the #50 Sieve
10.4
5.80
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.48
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.05
0.09
0.99
-0.17
-0.59
-0.21
0.00
0.04
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 174
100.0
96.6
Total Percent Passing the #4 Sieve
66.9
40.9
21.7Total Percent Passing the #50 Sieve
10.7
5.96
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.75
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.23
0.09
-0.87
0.14
0.58
0.19
0.18
0.13
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 176
100.0
96.8
Total Percent Passing the #4 Sieve
66.4
41.3
23.1Total Percent Passing the #50 Sieve
11.3
6.46
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.34
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.19
0.09
-0.50
-0.08
0.76
0.90
0.53
0.41
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 177
100.0
97.4
Total Percent Passing the #4 Sieve
68.0
42.2
23.6Total Percent Passing the #50 Sieve
11.8
6.30
5
5
5
4
4
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.35
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.84
0.09
0.61
0.62
1.16
1.15
0.82
0.32
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 178
100.0
97.3
Total Percent Passing the #4 Sieve
67.5
40.0
22.0Total Percent Passing the #50 Sieve
11.0
6.10
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 4.90
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.64
0.09
0.43
0.40
-0.17
0.34
0.35
0.21
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 179
100.0
96.8
Total Percent Passing the #4 Sieve
64.3
37.4
20.4Total Percent Passing the #50 Sieve
10.9
6.92
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.45
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.95
0.09
-0.50
-1.00
-1.00
-0.46
0.30
0.68
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 180
100.0
96.9
Total Percent Passing the #4 Sieve
66.8
40.6
22.9Total Percent Passing the #50 Sieve
11.7
6.60
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.23
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.31
0.09
-0.31
0.10
0.44
0.80
0.77
0.49
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 181
100.0
96.9
Total Percent Passing the #4 Sieve
66.9
41.6
23.1Total Percent Passing the #50 Sieve
11.5
6.40
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.70
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.18
0.09
-0.31
0.14
0.89
0.90
0.65
0.38
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 182
100.0
97.0
Total Percent Passing the #4 Sieve
68.1
41.1
23.0Total Percent Passing the #50 Sieve
11.4
6.19
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.98
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.46
0.09
-0.13
0.66
0.67
0.85
0.59
0.26
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 183
100.0
97.6
Total Percent Passing the #4 Sieve
68.3
41.6
22.9Total Percent Passing the #50 Sieve
11.2
6.17
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 5.01
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-0.53
0.09
0.99
0.75
0.89
0.80
0.47
0.25
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 184
538.6
520.3
Total Percent Passing the #4 Sieve
337.2
179.0
82.3Total Percent Passing the #50 Sieve
27.0
27.00
0
0
0
0
0
0
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 0.76
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-4.92
2,088.67
783.76
-118.17
-62.78
-30.80
-9.76
-12.09
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 185
99.9
97.1
Total Percent Passing the #4 Sieve
68.0
39.9
18.9Total Percent Passing the #50 Sieve
6.3
0.54
5
5
5
5
4
2
1
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.04
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.53
-0.38
0.06
0.62
0.13
-1.22
-2.41
-2.96
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 186
100.0
96.7
Total Percent Passing the #4 Sieve
59.9
31.0
12.2Total Percent Passing the #50 Sieve
2.8
0.22
5
5
1
0
0
0
0
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
0Percent Loss by T11 (P200 Wash) 0.78
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
-4.90
0.10
-0.69
-2.92
-3.88
-4.61
-4.47
-3.14
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 187
100.0
96.8
Total Percent Passing the #4 Sieve
67.5
41.3
22.1Total Percent Passing the #50 Sieve
11.0
6.50
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.38
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.88
0.09
-0.50
0.40
0.76
0.39
0.35
0.44
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below:
2017 Fine Aggregate Round Robin Report
Lab Number 189
100.0
97.0
Total Percent Passing the #4 Sieve
67.5
40.0
22.4Total Percent Passing the #50 Sieve
11.0
6.50
5
5
5
5
5
5
5
Total Percent Passing the #8 Sieve
Total Percent Passing the #16 Sieve
Total Percent Passing the #30 Sieve
Total Percent Passing the #100 Sieve
Total Percent Passing the #200 Sieve
Ratings Lab Results
5.53
Average
99.98
97.07
66.58
5Percent Loss by T11 (P200 Wash) 6.10
39.62
21.32
10.40
5.73
0.97
0.21
0.54
2.29
2.22
1.98
1.70
1.76
PopStdDev Z Score
0.59
0.09
-0.13
0.40
0.17
0.54
0.35
0.44
Rating = 5 corresponds to Z scores no greater than 1.0
Rating = 4 corresponds to Z scores greater than 1.0 but less than or equal to 1.5
Rating = 3 corresponds to Z scores greater than 1.5 but less than or equal to 2.0
Rating = 2 corresponds to Z scores greater than 2.0 but less than or equal to 2.5
Rating = 1 corresponds to Z scores greater than 2.5 but less than or equal to 3.0
Rating = 0 corresponds to Z scores greater than 3.0
If any of the individual results are less than or equal to a rating of 2, perform a brief labortory investigation in an attempt to document the potential
cause of this low rating (e.g. calculation error, equipment, or procedural). The documented results of this investigation should then be put on file in
the laboratory and kept for a period of no less than five years. This documentation should be made available to ODOT upon request. If any of the
individual results are less than or equal to a rating of 1 then the results of a completed laboratory investigation and copy of all calculations should be
immediately submitted to the OMM Aggregate Section. Detailed instructions regarding deadlines and other follow up instructions will be emailed to
these labs. If requested please submit all follow up documentation to: [email protected], or by mail to: OMM Aggregate
Section at 1600 W. Broad St., Columbus, Ohio 43213. Failure to respond in a timely manner may result in loss of S1069 laboratory and associated
producer/supplier prequalification.
The 2017 Round Robin study included a total of 151 participating laboratories. Each participating laboratory's results were entered into a combined
database and analyzed for basic statisics. This report displays the individual lab results submitted to the OMM Aggregate Section, the population
average, population standard deviation, Z score, and rating. The Z score indicates how many standard deviations away from the population average
each reported result is. Each rating is based upon a corresponding Z score range described below: