Lab 8 Facebowxfer
-
Upload
jaspreetkaur0410 -
Category
Documents
-
view
227 -
download
0
Transcript of Lab 8 Facebowxfer
-
7/28/2019 Lab 8 Facebowxfer
1/38
Face-Bow Transfer& Mounting of Maxillary Cast
-
7/28/2019 Lab 8 Facebowxfer
2/38
ArmamentariumFace-Bow
NasionRelator
Bard-Parker orLab KnifeOne sheet PinkBase-Pate Wax
Face-Bow(Bite) Fork
PlasterBowl forHot Water
Toggle & ShaftHardware
-
7/28/2019 Lab 8 Facebowxfer
3/38
Detailed Inventory of Facebow Device
-
7/28/2019 Lab 8 Facebowxfer
4/38
Support Barower Frame
JackScrew
Facebow Apparatus
-
7/28/2019 Lab 8 Facebowxfer
5/38
Adapting Wax to Bite-Fork
1. Identify the top of
the bite-fork
2. Place two
thicknesses of wax
on the top
3. Mould to form the
wax in a horseshoe
as illustrated
-
7/28/2019 Lab 8 Facebowxfer
6/38
Use Bunsen Burner to Heat
the Baseplate Wax
-
7/28/2019 Lab 8 Facebowxfer
7/38
Warm the Wax in Hot Water
Prior to this step, trythe horseshoe on
the the maxillary
cast to make sure
all of the occlusalsurfaces of the
maxillary teeth
including the buccal
cusps will beimprinted.
Make sure the wax extends beyond the last molar in the arch
-
7/28/2019 Lab 8 Facebowxfer
8/38
Insert & Align Bite Fork
1. Align the bite
fork with the
mid-line of the
maxilla
2. Hold bite fork
in place firmly
as wax cools
-
7/28/2019 Lab 8 Facebowxfer
9/38
Chill & Trim the Excess Wax
-
7/28/2019 Lab 8 Facebowxfer
10/38
Assembling Hardware to
Face-Bow
-
7/28/2019 Lab 8 Facebowxfer
11/38
Use of Cotton Rolls
Patient can assistin holding bite fork
in place but must
bite on cotton rolls
-
7/28/2019 Lab 8 Facebowxfer
12/38
Initial Placement of Face-Bow
1. After bite fork isrepositioned
2. Gently guide the
ear piece into the
external auditory
meatus
3. Patient applies
firmer pressureand holds in place
while pulling
forward at the
same time
-
7/28/2019 Lab 8 Facebowxfer
13/38
Initial Placement of Face-Bow
4. Note toggle & shaft
hardware are
already attached to
the face-bow at
this stage
-
7/28/2019 Lab 8 Facebowxfer
14/38
Nose Piece
1. Center the plastic
nose piece on the
patients nasion.
2. Tighten thumbscrew on the
nasion-relator
assembly
3. This secures the
vertical
relationship in the
sagittal plane
-
7/28/2019 Lab 8 Facebowxfer
15/38
Attaching Hardware
Loosely guide the
vertical bar &
horizontal cross
bar to the bite fork
shaft
Have patient look at
you. Make sure face
bow is parallel to an
imaginary line going
between the pupils.
-
7/28/2019 Lab 8 Facebowxfer
16/38
Attaching Hardware
1. Make sure the
horiz. cross bar
is above thebite fork shaft
-
7/28/2019 Lab 8 Facebowxfer
17/38
Attaching Hardware
2. Tighten the
T-screw on the
vertical bar
3. Tighten the
horizontal -
frontal T-screwas well
-
7/28/2019 Lab 8 Facebowxfer
18/38
-
7/28/2019 Lab 8 Facebowxfer
19/38
-
7/28/2019 Lab 8 Facebowxfer
20/38
-
7/28/2019 Lab 8 Facebowxfer
21/38
>Removing the Face-Bow