(l8) HVU n a R · GROUP NUMBER (l8) HVU n a R 11 nEW THlnKlnG. CAMPAIGN 14-01-027 nEW...

GROUP NUMBER

(l8) HVU n a R 11 nEW THlnKlnG. CAMPAIGN 14-01-027 nEW POSSIBILITIES.

DATE MODEL(S)

Technical Service Bulletin JULY 2014 GENESIS SEDAN (DH)

SUBJECT: ASSISTED DOOR MODULE (ADM) SOFTWARE UPDATE

(SERVICE CAMPAIGN TT6)

*IMPORTANT *** Dealer Stock and Retail Vehicles ***

Dealers must perform this Service Campaign on all affected vehicles prior to customer retail delivery and whenever an affected vehicle is in the shop for any maintenance or repair.

When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty Vehicle Information" screen via WEBDCS to identify open Campaigns.

Description: This bulletin provides the procedure to update the ADM module on certain Genesis Sedan Vehicles. When using the Blue Link remote start application , the passenger mirror puddle lamp does not turn on.

jApplicable Vehicles: Certain 2015 Genesis Sedans (DH)

ROM ID INFORMATION TABLE

ROMID Model System ADM P/N

Previous New

2015 GENESIS ADM SEDAN (DH) (Assisted 93575-81000-4X 9357581000 101 9357581000 102 3.8L & 5.0L Door Module)

Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service Advisors , Technicians , Body Shop Manager, Fleet Repair


• • • OP CODE OPERATION OP TIME 40C030RO ASSISTED DOOR MODULE (ADM) UPDATE 0.3 M/H

NOTE: Submit Claim on Campaign Claim Entry Screen .

GENERAL PRECAUTIONS:

Make sure the battery icon at the bottom right of the GOS laptop shows at least 50%. If not, charge the GOS or attach a battery charger.

• Make sure the GOS is updated to the latest version using internet smart update.

• Make sure the vehicle's battery has reasonable charge . If the vehicle has been in storage, run the engine to ensure an adequate battery charge for reliable results .

• Turn off all lights (do not leave the headlight switch in auto mode) and all accessories (including heater/air conditioner/fan for both front and rear(if equipped), audio , heated seats , rear defroster, etc.) to ensure the battery will not be discharged during the procedure .

• Perform the procedure with the ignition key in the ON position . (Turn ignition key to the ON position or press the Start-Stop button 2 times without depressing the brake pedal) .

• Do not disconnect any cables connected to the veh icle or the GOS during the procedure .

• Do not start the engine or turn the ignition switch OFF during the procedure.

SERVICE PROCEDURE:

1. Connect the USB cable between the GOS and the VCI.

2. Connect the 16-pin DLC connector from the VCI into the DLC located under the driver's side dash (within the fuse box).

3. Press the power button on the VCI to turn it ON.

4. Turn the ignition key to the ON position, or press the Start-Stop button 2 times without depressing the brake pedal.

TSB #: 14-01-027 of13


GOS AUTO MODE ADM UPDATE PROCEDURE

1. From the GOS home page, select ECU UPGRADE. After selecting ECU UPGRADE, if the GOS does not automatically detect the VIN , manually enter the VIN number.

-------------.- .,-c-1 -us_e_o_n ~---- -----ECRJ

Gi>)

D Vehicle Info 0

a Hot Fix

•By OTC

•By Symptom

•By Model

•Campaign

Gcito»

~3S#-;:;;;;;;;O/ll

Diagnos is

a Basic Inspection

j'. a DTC Analysis

D Data Ana lysis

D Flight Record

" a CARB OBD-11

TSB ~se ANtyiis OTC

2. Select ADM as the system and then select OK.

IKMHGN4JE4EU000550

. GENESIS(DH) ·

TSB # : 14-01 -027

User's Guide I Notice 0 I Configuration I Search

'I Vehicle S/W Management Repair

D Parts Catalog 0

D ID Register a Replacement

D Option Treatment D Component Info

a Data T reatment a C ircuit Diagram

D Inspection IT est

D ECU Mapping Verification 0

~ ~ Assist Door Module

~- cancel

of 13


3. Select AUTO MODE and then NEXT.

ID Register

Option Treatment

Data Treatment

Inspection I Test

ECUti.ppingVailicaion1

~--Setup -

Repair

Manual Mode

G CAUTION

1. DO NOT start the engine and DO NOT turn the igrition key to the OFF oosition during the ECU upgrade . 2. Ensure that the battery is fully charged BEFORE beginning ECU uograde. 3. Confirm the target vehicle/system BEFORE perfonming a manuaverror mode ECU upgrade. 4. Re..;ew the app~cable TSB/procedure before performing an ECU upgrade. 5. Make certain that the proper connector mentjoned in the related TSB is used. 6. Ensure that any applicable components are replaced BEFORE performing the ECU upgrade. 7. Confirm the new ROM ID after performing an ECU upgrade. 8. Do not remove the USB cable during upgrading the ECUI!

OTC Current Do ta

~

ACtuatiOn Test FlightReco1d

~ 0 E-Report

~ 8 lntemel Updd1e

FauhCode Sea rchiAQ

4 . Select ADM and then select OK.

•Mode Auto Mode

TSB #: 14-01-027

Preparation

( ... System Event List

~ a Preparation

1) Connect the DLC(Data Link Connect or) o f VCI t o the OBD - 11 connec tor of Vehicle side .

2) Turn on VCI unit 3) Check the syst em then. Click the OK button to continue .

OTC current Data ACIU!llioo Test FllQM Record

= 0 E-Repon

Fault Code searching

of13


5. The GOS will read the ROM ID. Confirm the ROM ID is applicable as shown on Page 1, "ROM ID Information Table". Select UPGRADE.

Mode Auto Mode

• System ADM

ID Register

Option Treatment

Data T realment

Inspection I Test

ECU IAapping Verificalion •

·~~~--

Preparation

• Event Group

., Current ROM ID

~ Latest ROM ID

D Event selection

1. Review and unders tand related TSB for vehicle reprogramming. 2. Select reprogramming event f rom Upgrade Event pull do wn menu above. 3. Click the Upgrade button to begin ECU upgrade.

OTC Current Dalli Actuation

Test Flight Record

~ 0 E-Report

Fault Code Searching

6. If the screen indicates "Voltage is OK" (voltage 12 volts or greater), select OK. If not, select CANCEL and charge the vehicle battery by running the engine for 10 minutes.

TSB #: 14-01-027

BATTERY VOLTAGE:12.00V

Voltage is OK.

Press OK to upgrade E CU. Press CANCEL to return

to previous screen.

of13


7. Update will begin and the progress of the update will appear on the bar graph. It will take approximately 5 minutes until the progress bar reaches 100%.

Mode Auto Mode

•System ADM

Event Group Message Not Found

•JI

• Current ROM ID

~ Latest ROM ID

19357581000_ 10 I

19357581000_ 102

Server -1 - GDS -,

CAUTION

l!I •

•During th e ECU Upgrade, observe U1e tollowlng e>recaullons. Failure Lo follow these orecautlons may result in ECU damage .

1. DO NOT operate any other comouter orosrams. 2. DO NOT disturb or disconnect the DLC(Data Link Connecto1), 3. 00 NOT tum off the VCI or DO NOT disconnect VCI USS Connector. 4. DO NOT start the vehicle or turn the IG key off. 5. DO NOT ooerate any of the vehicles other SYStems(climate control. lighting, audio, etc.>.

OTC CurrentOala Attu;,tlon

Test FHght Record

~ 0 E.Report

Fault Code Searching

8. When the update is complete , wait for a pop up screen shown below. Turn the ignition OFF for 10 seconds, and then turn it back ON (Press the Start-Stop button 2 times without depressing the brake pedal) . Select OK.

---- -- ---- - --- ------~--- ------------------ - --- - - --- - - - -c.~lnformation - - ---- - - -------

Tum IG off for 10 seco nds and th en back on. Cli ck the OK button to co ntinu e.

~ OK --! ------ -- ---- ----- ----

TSB #: 14-01-027 of 13


9. Wait for a pop up screen indicating the update was successful. Select OK.

Th e E CU Upgrade is successfully finished.

ROM ID: 9357581000 102

~ ·aK --- ------ - - -

10. Check if any incidental Diagnostic Codes (OTC) have been created by the update, and then clear all the OTC (s) . Select OK .

. a --1iitorrriation·--.---------- -·-- ---- - ----- -- -----

After E CU update must clear the

DTCs of CAN contro ller.

~ --1.ll.l!!ml'r .t.: , OK .I !____ -~ -- - - - --

11 . Clear any DTCs in the Blue Link system per instructions of TSB 12-BE-005-2 .

TSB #: 14-01-027 of13


GOS MANUAL MODE ADM UPDATE PROCEDURE

• The manual update should be performed only when the automatic update fails.

• If automatic update fails, turn the ignition key OFF for about 10 seconds, turn it back ON and then perform the manual update.

1. From the GOS home page, select ECU UPGRADE. After selecting ECU UPGRADE, if the GOS does not automatically detect the VIN , manually enter the VIN number.

Preparation

a Vehicle Info O

El Ho Fix

· Sy OTC

•By Symptom

•By Model

•Campargn

·;.:i i~» --- -/Jl"l.1,IW'VU-,,MI

Diagnosis

D Basic lnspeclion

D DTC Analysis

D Data Analysis

a Flight Record

a CARBOBD-11

.ore:

I Cunliuurellon S cwch

Vehicle SIW Management Repair

~- ;";pa;c;.,log o

D ID Regioter D Replacemen

IJ Option Treatment a Component Info

a Data Treatment D C1rcud Diagram

D Inspection I T est

a ECU Mapping Verif.aticn 0

2. Select ADM as the system and then select OK.

IKMHGN4JE4EU000550 ::J

GENESIS{DH) . ·

~ Assist Door Module

'l!!""r' • Cancel ·

TSB#: 14-01 -027 of13


3. Select MANUAL MODE and then NEXT.

ID Register

Option Treatment

Data Treatment

Inspection IT est

ECU I.lapping Vt!i!iC.Jtion f,

~ --serup :

4. Select ADM and then NEXT.

TSB #: 14-01-027

ID Register

Option Treatment

Data Treatment

Inspection I Test

ECU Mapping VerifiC.Jtion r

"! .•

a CAUTION

l. DO NOT start the engine and DO NOT turn the ignition key to the OFF posibon during the ECU upgrade . 2. Ensure that the battery is fully charged BEFORE beginning ECU upgrade. 3. Confirm the target vehicle/syStem BEFORE pertorming a manuaverror mode ECU upgrade. 4. Review the applicable TSB/procedure before pertorming an ECU upgrade. 5. Make certan that the proper connector mentioned in the related TSB is used. 6. Ensure that any applicable components are replaced BEFORE performing the ECU upgrade. 7. Confirm the new ROM ID after pertorming an ECU upgrade. 8. Do not remove the USS cable during upgrading the ECUll

CoseAMlysis OTC

a CAUTION

Current Data Acwauon Test

Diagnosis

J' Event List

FlightReco1d

~ o

E-Report

~ It Internet Upddte

A!'.C"'.,i;i::Previous • Next ~ _, -----

Repair

~

F21ultCode Se~n;hing

1. DO NOT start the engine and DO NOT turn the ignition key to the OFF position during the ECU upgrade. 2. Ensure that the battery is fully charged BEFORE beginning ECU upgrade. 3. Confirm the target vehicle/syStem BEFORE pertorming a manuaverror mode ECU upgrade. 4. Re\liew the applicable TSB/procedure before performing an ECU upgrade. 5. Make certain that the proper connector mentioned in ttle related TSB is used .. 6. Ensure that any applicable components are replaced BEFORE performing the ECU upgrade. 7. Confirm the new ROM ID after pertorming an ECU upgrade. 8. Do not remove the USS cable during upgrading the ECU! !

OTC Current Data ACtuatfon

Test FliohtRecord

= It E·Report

= " ~ 1~~~e1 ECU ijp r~e

~ FnultCode Searching

..:J

.:J

of 13


5. Select the update event "322 DH 3.8/5.0 ADM PUDDLE LAMP LOGIC IMPROVEMENT" and then select NEXT.

Gi>)

•System ADM

Preparation

. . it'.r..i'.v Previous ,.

a Preparation

1) Connect the DLC(Data Link Connector) of VCI to the 080- 11 connector of Vehic le s ide.

2) Turn on VCI unit 3) Check the system then. Click the OK button to continue .

Cue Analysis OTC Current Data Actuation

Test fllqht Reco1d

~ 0 e.Repon

6. Select "322 DH 3.8/5.0 ADM PUDDLE LAMP LOGIC IMPROVEMENT" on the screen , and then select UPGRADE. A pop up screen will request for a Password. Enter 1000 and then select OK.

Password I ••••I

TSB #: 14-01-027 Page10of13


7. If the screen indicates "Voltage is OK" (voltage 12volts or greater), select OK. If not, select CANCEL and charge the vehicle battery by running the engine for 10 minutes.

BATTE RY VOLTAGE :12.00V

Voltage is OK.

Press OK to upgrade ECU. Press CANCEL to return

to previous screen.

~I I

---------- - - - - - --

8. Update will begin and the progress of the update will appear on the bar graph . It will take approximately 5 minutes until the progress bar reaches 100% .

TSB #: 14-01-027

• Mode

M:mual Mode-

• Sy stem

ADM

• Event Group 322.0H J .Bl~.O ADM PUOO•

ID Register

Option Treatment

Data Treatment

Inspection /Test

ECU Mapping Verification }

• Current ROM ID

• Latest ROM ID 19357561000_ 102

Server

0 CAUTION • During t he ECU Upgrade, observe the following precautions . Failure to follow these precautions may resull in ECU damage.

1) DO NOT operate any other computer program. 2) DO NOT disturb or disconnect the DLC(Data Link Connector). 3) DO NOT turn off the VCI or DO NOT disconnect VCI USB Connector. 4) DO NOT start the vehicle or turn the IG key off. 5l DO NOT operate any of the vehicles other syStems(climate control. lighting. audio. etc.)

l~--- OTC Currencoaia Actualion Test Fl/9hl Record

~ .

e-Report

of 13


9. When the update is complete , wait for a pop up screen shown below. Turn the ignition OFF for 10 seconds , and then turn it back ON (Press the Start-Stop button 2 times without depressing the brake pedal). Select OK.

• · · lnf~mirti~~ -: ~::.:::.__:_::._ ··__:_::.: -=--~-- _: _:_ ·--- . ·.· .. :.:::.:::.:~-::-::· · ~ · - - -

Turn IG off fo r 10 seconds and th en back on. Click th e OK button to co ntinue.

~~--

~·· oK . l I--~--- - ---- -- ---

10. Wait for a pop up screen indicating the update was successful. Select OK.

Th e ECU Upgrade is successfully finished.

ROM ID : 935758 1000 102

~ OK -I ------- - - --- --

TSB #: 14-01 -027 of 13


11. Check if any incidental Diagnostic Codes (OTC) have been created by the update, and then clear all the OTC (s) . Select OK.

-&= 1nformation ·=-==--::::-:: -~::.·::_:~:·-_-__:_:=:- :-_ ____ :--__:-: -- :. --:--:---:·- -"""'"'":--- -- ---

After E CU u11<late must clear the

DTCs of CAN co ntro ller.

12. Clear any DTCs in the Blue Link system per instructions of TSB 12-BE-005-2.

TSB #: 14-01-027 of13

(l8) HVU n a R · GROUP NUMBER (l8) HVU n a R 11 nEW THlnKlnG. CAMPAIGN 14-01-027 nEW...

Documents

Transcript of (l8) HVU n a R · GROUP NUMBER (l8) HVU n a R 11 nEW THlnKlnG. CAMPAIGN 14-01-027 nEW...