L13.13 LOCKING PULLS SERIES 669D AND 668D · · 2019-11-29LOCKING PULLS SERIES 669D AND 668D...

LOCKING PULLSSERIES 669D AND 668D

L13.13

L13

SLIDING DOORS

01.05.2014

Waregemstraat 5 - 9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - [email protected] - www.sobinco.com

CONTENT

1. Non-automatic hand pulls series 669D ..............................L13.13.031.1. Inside, with hook, n° 669D-1, -11, -12 L13.13.031.2. Inside, with hook, n° 669E-1, -11, -12 L13.13.041.3. Inside, with bolt, n° 669D-14.. and n° 669D-15.. L13.13.05

2. Automatic hand pulls series 668D ......................................L13.13.062.1. Inside, with hook, n° 668D-1, -11, -2, -12 L13.13.062.2. Inside, with hook, n° 668H-1, -11, -2, -12 L13.13.072.3. Inside, with hook, n° 668E-1, -11, -2, -12 L13.13.082.4. Inside, with hook, n° 668I-1, -11, -2, -12 L13.13.092.5. Inside, with bolt, n° 668D-4, -14, -5, -15 L13.13.102.6. Outside, with bolt, n° 668G-6, -16, -7, -17 L13.13.11

3. Fixed hand pull series 669D ................................................L13.13.123.1. Without cylinder, n° 669D-21 and n° 669D-21C L13.13.123.2. Outside, with cylinder, n° 669D-22.. L13.13.13

4. Fixedfingerpullsn°669-31andn°669-32.. .....................L13.13.14

5. Hookwedges ........................................................................L13.13.155.1. Hook wedges n° 668D-8 and n° 668D-18 L13.13.155.2. Hook wedges n° 6680-.. L13.13.165.3. Wedge selection L13.13.18

6. Assembly hand pulls with cylinder .....................................L13.13.19

L13.13.02 DOOR HANDLES

LOCKING PULLS SERIES 669D AND 668D

L13.13

1. Non-automatic hand pulls series 669D1.1. Inside,withhook,n°669D-1,-11,-12

• Application: 2-part and 4-part sliding doors (with fixed hand pull n° 668D-8 or n° 668D-18).

• The hand pulls do not lock automatically upon closing the door.

• The locking occurs by pushing in the black button on the side. Even if the button has been pushed in in advance, the pull will unlock upon closing the door. Therefore you cannot accidently lock yourself out.

• To unlock slightly press with the fingers on the pull.

• The pulls are non-handed.

• Finish: aluminium anodised or polyester powder coated (more than 450 RAL colours).

• Very simple installation: drill and tap 2 round holes in the vent section. Screw the base of the pull on the vent section, slide the moving part into the base and clip the black plastic cover plates on both ends of the pull.

• Assembly hand pull with cylinder n° 669D-12: see page L13.13.19.

n° 669D-1

OUTSIDE

INSIDE

4-part sliding door:see page L13.13.15

n° 669D-1n° 669D-11

n° 669D-12with cylinder

Order code L (mm) G (mm)669D-1 120 100669D-11 180 160

DOOR HANDLES L13.13.03


L13.13

1.2. Inside,withhook,n°669E-1,-11,-12

• Same type as hand pulls n° 669D-.. , but with different hook.


• The hand pulls do not lock automatically upon closing the door.

• The locking occurs by pushing in the black button on the side. Even if the button has been pushed in in advance, the pull will unlock upon closing the door. Therefore you cannot accidently lock yourself out.

• To unlock slightly press with the fingers on the pull.

• The pulls are non-handed.



• Assembly hand pull with cylinder n° 669E-12: see page L13.13.19.

Order code L (mm) G (mm)669E-1 120 100669E-11 180 160

n° 669E-1n° 669E-11

n° 669E-12with cylinder

OUTSIDE

INSIDEn° 669E-1




L13.13

1.3. Inside,withbolt,n°669D-14..andn°669D-15..

• Application: 2-part and 3-part sliding doors.

• Characteristics and finish: see page L13.13.03.

• The bolts, in brass zinc plated, are adjustable and available in different lengths. When ordering please indicate the bolt type. See table above.

• Adjustment of the length, as well as orientating the bolt to the left or the right can be done easily with an open-ended spanner of 8 mm.

• The hand pull is used in combination with wedge n° 665-40.

• Assembly hand pull with cylinder n° 669D-15.. : see page L13.13.19.

n° 669D-14..

OUTSIDE

INSIDE

3-part sliding door

Wedge n° 665-40in grey plastic

Bolt type

LengthSadjustablefrom .. to ..

A 27 - 34 mmB 34 - 42 mmC 42 - 50 mmD 50 - 58 mmE 58 - 66 mmF 66 - 74 mm

n° 669D-14..

thro

w =

7 m

m

n° 669D-15..with cylinder

thro

w =

7 m

m



L13.13

2. Automatic hand pulls series 668D2.1. Inside,withhook,n°668D-1,-11,-2,-12


• The hand pulls lock automatically upon closing the door.

• To unlock slightly press the pull with your fingers.

• The hand pulls are non-handed.



• Assembly hand pulls with cylinder n° 668D-2 and n° 668D-12: see page L13.13.19.

n° 668D-1n° 668D-11

Order code

LengthL (mm)

668D-1 120668D-11 180668D-2 120668D-12 180

n° 668D-2n° 668D-12with cylinder

n° 668D-1

OUTSIDE

INSIDE




L13.13

2.2. Inside,withhook,n°668H-1,-11,-2,-12

• Application: 2-part sliding doors.

• The hand pulls are similar to the ‘D’ type (see page L13.13.06), but are more specific to use in combination with the hand pulls n° 668G-.. : see page L13.13.11. Attention: the combination with a cylinder locking hand pull on the inside as well as on the outside is not possible.






• Assembly hand pulls with cylinder n° 668H-2 and n° 668H-12: see page L13.13.19.

n° 668H-1n° 668H-11

Order code

LengthL (mm)

668H-1 120668H-11 180668H-2 120668H-12 180

n° 668H-2n° 668H-12with cylinder

n° 668H-..

OUTSIDE

INSIDE



L13.13

2.3. Inside,withhook,n°668E-1,-11,-2,-12

• Same type as hand pulls n° 668D-.. , but with different hook.







• Assembly hand pulls with cylinder n° 668E-2 and n° 668E-12: see page L13.13.19.

Order code

LengthL (mm)

668E-1 120668E-11 180668E-2 120668E-12 180

n° 668E-1n° 668E-11

n° 668E-2n° 668E-12with cylinder

n° 668E-1

OUTSIDE

INSIDE




L13.13

2.4. Inside,withhook,n°668I-1,-11,-2,-12


• The hand pulls are similar to the ‘E’ type (see page L13.13.08), but are more specific to use in combination with the hand pulls n° 668G-.. : see page L13.13.11. Attention: the combination with a cylinder locking hand pull on the inside as well as on the outside is not possible.






• Assembly hand pulls with cylinder n° 668I-2 and n° 668I-12: see page L13.13.19.

n° 668I-1n° 668I-11

Order code

LengthL (mm)

668I-1 120668I-11 180668I-2 120668I-12 180

n° 668I-2n° 668I-12with cylinder

n° 668I-..

OUTSIDE

INSIDE



L13.13

2.5. Inside,withbolt,n°668D-4,-14,-5,-15

• Application: 2-part and 3-part sliding doors.• Characteristics and finish: see page

L13.13.06.• The bolts, in brass zinc plated, are adjustable

and available in different lengths. When ordering please indicate the bolt type. See table above.

• Adjustment of the length, as well as orientating the bolt to the left or the right can be done easily with an open-ended spanner of 8 mm.

• The hand pull is used in combination with wedge n° 665-40.

• Assembly hand pulls with cylinder n° 668D-5.. and n° 668D-15.. : see page L13.13.19.

Order code

LengthL (mm)

668D-4 120668D-14 180668D-5 120668D-15 180

Bolttype

LengthSadjustablefrom .. to ..

A 27 - 34 mmB 34 - 42 mmC 42 - 50 mmD 50 - 58 mmE 58 - 66 mmF 66 - 74 mm

n° 668D-14..

OUTSIDE

INSIDE

3-part sliding door

n° 668D-4..n° 668D-14..

thro

w =

7 m

m

n° 668D-5..n° 668D-15..with cylinder

thro

w =

7 m

m

Wedge n° 665-40in grey plastic



L13.13

2.6. Outside,withbolt,n°668G-6,-16,-7,-17


• Characteristics and finish: see page L13.13.06.

• The bolts, in brass zinc plated, are adjustable and available in different lengths. When ordering please indicate the bolt type. See table above.

• Adjustment of the length can be done easily with an open-ended spanner of 8 mm.

• The hand pull is used in combination with the hand pulls 668H-.. or 668I-..: see page L13.13.07 and L13.13.09. Attention: the combination with a cylinder locking hand pull on the inside as well as on the outside is not possible.

• Assembly hand pulls with cylinder n° 668G-7 and 668G-17.. : see page L13.13.19.

n° 668G-6n° 668G-16

n° 668G-7n° 668G-17with cylinder

Order code

LengthL (mm)

668G-6 120668G-16 180668G-7 120668G-17 180

Bolt type

LengthSadjustable from .. to ..

SectiondepthB (mm)

A 27 - 34 mm 14 - 21 mmB 34 - 42 mm 21 - 29 mmC 42 - 50 mm 29 - 37 mmD 50 - 58 mm 37 - 45 mmE 58 - 66 mm 45 - 53 mmF 66 - 74 mm 53 - 61 mmG 74 - 82 mm 61 - 69 mm

n° 668G-..OUTSIDE

INSIDE



L13.13

3. Fixed hand pull series 669D3.1. Withoutcylinder,n°669D-21andn°669D-21C

• The fixed hand pull outside n° 669D-21 is generally used in combination with hand pulls inside n° 669D-11, n° 669D-12, n° 669E-11, n° 669E-12, n° 668D-11, n° 668D-12, n° 668E-11 or n° 668E-12.

• The fixed hand pull outside n° 669D-21-120 is generally used in combination with hand pulls inside n° 669D-1, n° 669E-1, n° 668D-1, n° 668D-2, n° 668E-1 or n° 668E-2.


• The fixed hand pulls are non-handed.

n° 669D-21n° 669D-21-120

Order code LengthL (mm)

669D-21 180669D-21-120 120669D-21C 180669D-21C-120 120

n° 669D-21Cn° 669D-21C-120



L13.13

3.2. Outside,withcylinder,n°669D-22..

• The fixed hand pulls outside with cylinder n° 669D-22.. are used exclusively in combination with hand pulls inside n° 669D-11 and n° 669E-11.

• The fixed hand pulls outside with cylinder n° 669D-22-120.. are used exclusively in combination with hand pulls inside n° 669D-1 and n° 669E-1.

• The spindle length of n° 669D-22E to M varies in accordance with the section depth. When ordering please indicate the spindle type. See table above.



669D-22.. 180669D-22-120.. 120

n° 669D-11

OUTSIDE

INSIDE

n° 669D-22..

INSIDEn° 669D-11

OUTSIDEn° 669D-22..

n° 669D-22E to Mn° 669D-22-120E to M

Spindletype

SpindlelengthA (mm)

SectiondepthB (mm)

E 22 15 - 20 mmF 27 20 - 25 mmG 32 25 - 30 mmH 37 30 - 35 mmI 42 35 - 40 mmJ 47 40 - 45 mmK 52 45 - 50 mmL 57 50 - 55 mmM 62 55 - 60 mm



L13.13

4. Fixed finger pulls n° 669-31 and n° 669-32..

• The fixed finger pull outside n° 669-31 is generally used in combination with hand pulls inside n° 669D-11 or n° 669E-11.

• The fixed finger pulls outside with cylinder n° 669-32.. are used exclusively in combination with the hand pulls inside n° 669D-11 or n° 669E-11.


• The spindle length of n° 669-32.. varies in accordance with the section depth. When ordering please indicate the spindle type. See table below.

n° 669-31 n° 669-32..with cylinder

Dimensions of the cut-out in

the vent section

INSIDEn° 669D-11

OUTSIDEn° 669-32..

n° 669D-11

OUTSIDE

INSIDE

n° 669-32..

Spindletype

SpindlelengthA (mm)

SectiondepthB (mm)

C 12 15 - 20 mmD 17 20 - 25 mmE 22 25 - 30 mmF 27 30 - 35 mmG 32 35 - 40 mmH 37 40 - 45 mmI 42 45 - 50 mmJ 47 50 - 55 mmK 52 55 - 60 mmL 57 60 - 65 mmM 62 65 - 70 mm



L13.13

5. Hook wedges5.1. Hookwedgesn°668D-8andn°668D-18

• The hook wedge is part of the hand pull.


• The fixed hand pulls are only used for double sliding doors with 2 vents sliding on the same track.


• Cover plates in black plastic.

Order code

LengthL (mm)

668D-8 120668D-18 180

668D-8668D-1668D-2669D-1

668D-18

668D-11668D-12669D-11669D-12

668D-8668E-1668E-2669E-1

668D-18

668E-11668E-12669E-11669E-12

n° 668D-8

OUTSIDE

INSIDE

n° 668D-1



L13.13

5.2. Hookwedgesn°6680-..• They are used in combination with hand pulls series 669D, 669E, 668D and 668E.• Finish: aluminium anodised or polyester powder coated (more than 450 RAL colours).

n° 6680-5n° 6680-6

n° 6680-7n° 6680-8

n° 6680-15n° 6680-16

n° 6680-17n° 6680-18

n° 6680-19n° 6680-20

n° 6680-21n° 6680-22

n° 6680-23n° 6680-24

n° 6680-25n° 6680-26

n° 6680-27n° 6680-28

Order code

LengthL (mm)

6680-5 1206680-6 1806680-7 1206680-8 1806680-15 1206680-16 1806680-17 1206680-18 1806680-19 1206680-20 1806680-21 1206680-22 1806680-23 1206680-24 1806680-25 1206680-26 1806680-27 1206680-28 180



L13.13


6680-27 BIS 1206680-28 BIS 1806680-29 1206680-30 1806680-31 1206680-32 1806680-35 1206680-36 1806680-37 1206680-38 1806680-39 1206680-40 1806680-41 1206680-42 1806680-54-120 1206680-54 180

n° 6680-27 BISn° 6680-28 BIS

n° 6680-29n° 6680-30

n° 6680-31n° 6680-32

n° 6680-35n° 6680-36

n° 6680-37n° 6680-38

n° 6680-39n° 6680-40

n° 6680-41n° 6680-42

n° 6680-54-120n° 6680-54



L13.13

5.3. Wedgeselection

Wedgeandhookofhandpull• Notes:

- Dimension A: this is when wedge and hook are touching each other in closed position.

- Dimension B: the first figure determines the ideal engagement of 4.5 mm between wedge and hand pull.

n° 6680-..

n° 669D-..n° 669E-..n° 668D-..n° 668E-..

n° 6680-..

n° 669D-..n° 669E-..n° 668D-..n° 668E-..

n° 6680-..

n° 669D-..n° 669E-..n° 668D-..n° 668E-..

Wedge A (mm)from ... to ...

B (mm)SeriesD

B (mm)SeriesE

6680-5, 6 25.5 31.5 4.3 - 6.1 2.7 - 4.56680-7, 8 31 - 4.3 - 6.1 2.7 - 4.56680-19, 20 49 - 4.8 - 6.3 3.2 - 4.76680-25, 26 40.5 - 4.8 - 5.8 3.2 - 4.26680-27, 28 48 - 10.3 - 11.3 8.7 - 9.76680-27 BIS 44 50 10.3 - 11.3 8.7 - 9.76680-28 BIS 44 50 10.3 - 11.3 8.7 - 9.76680-37, 38 32 38 7.3 - 9.3 5.7 - 7.76680-41, 42 27 33 7.3 - 9.3 5.7 - 7.76680-54 45.6 - -1 - 0 -2.8 - -1.8


B (mm)SeriesD

B (mm)SeriesE

6680-15, 16 23 - 1.2 - -1.2 2.8 - -1.46680-17, 18 22.5 28.5 6.2 - 3.7 7.8 - 3.66680-29, 30 53.5 - 18.2 - 15.7 19.8 - 17.36680-31, 32 27 - 11.2 - 8.7 12.8 - 8.66680-35, 36 43 - 12.7 - 11.2 14.3 - 12.86680-39, 40 61.5 - 18.2 - 17.2 19.8 - 18.8


B (mm)SeriesD

B (mm)SeriesE

6680-21, 22 54.5 - 19.3 - 20.8 17.7 - 19.26680-23, 24 41.5 - -9.7 - -7.3 -11.3 - -7.3



L13.13

6. Assembly hand pulls with cylinderAppliestothefollowinghandpulls: - 669D-12 - 669D-15 - 669E-12 - 668D-2 - 668D-5 - 668D-12 - 668D-15 - 668E-2 - 668E-12 - 668G-7 - 668G-17 - 668H-2 - 668H-12 - 668I-2 - 668I-12

Disassembly:• Remove the black plastic cover plates.

• Unlock the cylinder: turn the key to the right.

• Place the hook in open position.

• Unscrew the grub screw.

• Slide out the hook in open position towards the screw.

Assembly:• Screw the main section to the door.

• Unscrew the grub screw.

• Unlock the cylinder.

• Slide in the hook in open position from the screw side.

• Screw in the grub screw into the cut-out in the hook.

• Place the hook in closed position.

• Clip the black plastic cover plates on both ends of the pull.

• Check the operation: locking and unlocking of the cylinder.

Unlocking

Slide out

Main section

Knob

Hook

Grub screw



L13.13

L13.13 LOCKING PULLS SERIES 669D AND 668D · · 2019-11-29LOCKING PULLS SERIES 669D AND 668D...

Documents

Transcript of L13.13 LOCKING PULLS SERIES 669D AND 668D · · 2019-11-29LOCKING PULLS SERIES 669D AND 668D...