KTM RC 250 MOTO3/FACTORY 2012...KTM RC 250 MOTO3/FACTORY 2012 Material included in the bike sale...
Transcript of KTM RC 250 MOTO3/FACTORY 2012...KTM RC 250 MOTO3/FACTORY 2012 Material included in the bike sale...
KTM RC 250 MOTO3/FACTORY 2012
Material included in the bike sale package
1. Chassis Spec Factory chassis 2012 factory
Geometry Checked by laser system (with documentation)
Headstock inserts
-6/-1º
-6/-0.5º
Pivot point inserts
+/- 6
+/- 5
+/- 4
+/- 3
+/- 2
+/- 1
0
Tripple clamp (magnesium t. clamps)
Offset 28mm
Offset 30mm
Footrest
-10 mm with heel protector
Handlebar clamps
+ 10mm
Standard on the bike
Rizoma front brake lever protector
2. Suspensions 2012 WP Fork upgraded (Extension plug / new valving 2a1j / top out spring fully engaged )
2012 WP Shock upgraded (Top out spring 155 x 7
2013 WP Steering damper
3. Body Work 2012 top fairing modified (enlarged side areas)
Belly pan modified (front part for using -6/-1º headstock insert + sides for using Akrapovic 2013 twin exhaust).
Rear tail carbon pad + 75 mm
Rear fender large
Swingarm carbon protector
Cranckase oil breather reservoir with silicon hoses
Airbox cover with heat isolation
4. Engine 2012 factory engine upgraded
Conrod + piston kit factory 2013
Cylinder head 2012 with ports upgraded
Camshaft + valves kit factory 2013
Gearbox standard (E option + primary 64)
Suter Slipper clutch
Exhaust:
Complete exhaust Akrapovic 2012 evo 4 with coating
Complete exhaust Akrapovic 2013 twin with coating
5. Throttle body 2012 factory spec upgraded with heat protection on carbon plate
6. Cooling system / fuel tank 2012 Factory radiator MB with Venair heat protected silicon hoses
2012 Factory evo 3 fuel tank with heat isolation
Fuel line with heat protection
Fuel line connector Stäubli
7. Brakes / wheels Front brake line
Front brake pump Brembo 16 x 16 with short foldable lever
Front caliper brembo for double disc system
Front brake disc Brembo 4 x 218 m with special bolt for front wheel speed 2D sensor
Rear brake line
Rear brake pump Brembo factory with brake fluid reservoir integrated
Rear brake disc Brembo 4 x 190 mm with sensor wheel for rear wheel speed sensor
Brembo rear wheel caliper
Wheels 2013 Magnesium OZ Cativa
8. Electronics 2012 factory electronics that included:
Dellorto ECU with 2012 firmware
Dellorto Dash
Front / Rear Brake Pressure sensor
Front 2D Speed Sensor
Rear KTM Speed Sensor
Airbox Pressure Sensor
Engine Sensors - TPS sensor - BPS sensor - Water / Oil Temperature Sensor - Oil Pressure Sensor - Fuel Pressure Sensor - Gear position sensor - RPM Sensor
Widelambda sensor
Front / rear suspension sensor
Quickshifter factory 2012
Battery: - Battery factory 2012
9. Spare package with bike 1 set of handle bar + clamps complete
1 set of footrest complete
1 set of rims complete with brake disc
1 set of bodywork complete
2 battery
2 rear shock springs ( 1 step over and 1 step below the one on the bike)
2 pairs front springs (1 step over and 1 step below the one on the bike)
PRICE FOR THE TOTAL PACKAGE BIKE + ABOVE MENTIONED PARTS
28.000€
Optional material for the bike PRICE Spare engine complete 2013 spec with 1600 km total 4000€