KT_12N7_4A
2
This battery is specially designed as a high-performance battery used for motorcycle. The characteristics are high cranking AMPS, High vibration resistant and long cycle life. Polarity Exhaust KEYKO Technologies, LLC. KT 12N7-4A Specification Nominal Voltage 12 Volts Nominal Capacity (10H-R) 7 Ah Approximate Weight (With Acid) 5.93 lbs.(2.69 kgs) Recommended Maximum 2.1 A Charging Current Limit Equalization and Cycle Service 14.8 VDC/unit Average at 25°C Cycle Life (JIS D 5302:2004) 350 Terminal Type 6 Country of Origin Made in China (Fujian, China) Physical Dimensions (mm) L:5.31”(135mm) H:5.24”(133mm) W:2.95”(75MM) All data subject to change without notice. Terminal Configuration Before filling, ensure your new battery is the correct size for your vehicle. Once the battery is filled, it cannot be returned to vendor. Only use acid 128gr/ml for the battery Fill all cells to the “FULL” mark and wait 30 minutes. After 30 minutes, any cell that has settled below the “FULL” mark should be topped off the “FULL” mark. Replace the sealer caps before charging the battery. ✪ ✪ ✪ ✪ ✪ ✪ Filling Instructions [email protected] Front Side Terminals
-
Upload
jesus-maestre -
Category
Documents
-
view
215 -
download
0
description
manual
Transcript of KT_12N7_4A
This battery is specially designed as a high-performance battery used for motorcycle. The characteristics are high cranking AMPS, High vibration resistant and long cycle life.
Polarity Exhaust
KEYKO Technologies, LLC.
KT 12N7-4A
Specification Nominal Voltage 12 Volts Nominal Capacity (10H-R) 7 Ah Approximate Weight (With Acid) 5.93 lbs.(2.69 kgs) Recommended Maximum 2.1 A Charging Current Limit Equalization and Cycle Service 14.8 VDC/unit Average at 25°C Cycle Life (JIS D 5302:2004) 350 Terminal Type 6 Country of Origin Made in China (Fujian, China)
Physical Dimensions (mm)
L:5.31”(135mm) H:5.24”(133mm) W:2.95”(75MM) All data subject to change without notice.
Terminal Configuration
Before filling, ensure your new battery is the correct size for your vehicle. Once the battery is filled, it cannot be returned to vendor. Only use acid 128gr/ml for the battery Fill all cells to the “FULL” mark and wait 30 minutes. After 30 minutes, any cell that has settled below the “FULL” mark should be topped off the “FULL” mark. Replace the sealer caps before charging the battery.
✪
✪
✪
✪
✪
✪
Filling Instructions
Front Side Terminals
This battery is specially designed as a high-performance battery used for motorcycle. The characteristics are high cranking AMPS, High vibration resistant and long cycle life.
Certification of Inspection
Model KT 12N7-4A UPC Code 738435096021
Test standard JB/T 4282-2007 JIS 5302-2004
Test item content and result
N0 Item Standard Test Data Result Remark
1 Dimension
(LxWxH) 135*75*133 mm 135*75*133 mm Pass
2 Appearance Good Pass
3 Assemble Figure Pass
4 Instant High Rate
Discharge (250C）
Discharge current: 60A
5th Sec Voltage/9.3V
Discharge time/1.5 min
Discharge current: 60A
5th Sec Voltage: 10.4V
Discharge time: 2M09S
Pass
5
Low Rate
Discharge
Capacity
（250C）
The third time or before the
third time
C10/95%
Discharge Current：0.7A
Discharge Time ：
10H05min21S
C10=100.1%
Pass
6 Low Temperature
Discharge(-100C)
Discharge current: 56A
5th Sec Voltage/9.3V
Discharge time/1.5 min
Discharge current: 56A
5th Sec Voltage: 10.12V
Discharge time: 1M36S
Pass
7 Weight 2.69 KG
8 Conclusion This battery is up to JB/T 4282-2007、JIS 5302-2004 standard.
KT 12N7-4A KEYKO Technologies, LLC.
