Knx Pushbuttons

�ISC01217_V2.0_09_2009_EN

Content

KNX

Presentation 2

QuickSelectionGuide 10

Systemcomponents 23

Interfaces/gateways 29

Push-button 32

Binaryinputs 59

Movementdetector 63

Othersensors 73

Switchactuators 80

Blind/switchactuators 87

Dimmingactuators/controlunits 90

Controlanddisplaydevices 95

Roomtemperaturecontrolunits 100

Accessories 124

Index 125

Howtomakeyourbuilding“smart”KNX

��

FlexibilityConsidering that most buildings are designed for use over several decades, it’s inevitable that, sooner or later, the uses to which its rooms are put will change. The obvious solution: building functions which can be adapted to the needs of the user easily and cost-effectively, without tearing open walls and laying new cables.

ComfortEveryone nowadays expects more comfort and con-venience in their domestic and working lives. A modern electrical installation that can be operated conveniently, simply and comfortably makes living and working just that much easier.

Cost efficiencyNot only the one-off construction costs, but also the subsequent running costs are decisive in ensuring the cost efficiency of an investment of this kind. The following applies: the greater the flexibility with which building technology can react to new demands and be adapted to technical innovations, the greater its value for money. And when a growing environmental con-sciousness and increasing energy costs are taken into account, it is becoming ever clearer that building management must also incorporate intelligent solutions for energy efficiency as well.

SafetyandsecurityIf a building is to be as safe as possible, building technology must be able to react quickly and intelligently in critical situations, whether someone is on the premises or not. Given the extent and range of these different requirements, conventional electrical installations soon reach the limits of their capabilities. They can only do so much. As a result, adapting the use to which parts of the building are put can quickly prove costly, and coordinating the functioning of the different buildings is a major undertaking.

However, all this is no reason for you to change your plans. After all, there is an intelligent alternative to the conventional solution: KNX from Schneider Electric. Or to put it another way: clever buildings

Anyoneplanningtobuildanewprivatehomeorcommer-cialbuildingcanexpectmorethanjustalotofhardwork.Theyalsofacethechallengeofmeetinganynumberofindividual technical and financial requirements. And these demandshaveincreasedenormouslyinrecentyears.Thisisparticularlytrueintheareasofbuildingmanagementandelectricalinstallation,wheremanydifferentfactorshavetobetakenintoaccount.

Canallyourdemandsbemetunderoneroof?

��

��

��

In terms of comfort, take the following example: Getting cosy in the evening no longer means going from one switch or thermostat to the next. Instead, simply press a single button to activate all the desired

LivingthegoodlifeKNXinprivatebuildings

functions in one go: blinds are lowered, atmospheric lighting is switched on and the room is heated to just the right temperature. Settings such as these (known as scenes) can be created exactly as you want them.

Timed heating control:

Pleasant room temperatures via individual temperature control of the individual rooms.

Heating costs reduced thanks to time control of the heating valves.

A healthy sleeping climate due to automatic reduction of heating at night.

Room temperature is automatically lowered when the windows are opened, leading to further reductions in heating costs.

Intelligent blind control:

Central control of the electrically operated roller shutters and blinds in the study, parents’ bedroom and children’s room at the press of a button.

Automatic protection from excessive sunlight or storms is provided by awnings and blinds that react to sun and wind sensors.

Protection against burglary is provided by time-controlled roller shutters and blinds that also protect windows when nobody is at home.

IP Touch-Panel 10" Design Merten M-Plan

Individual lighting control:

The “Central Off” switch at the entrance door deactivates all loads, such as the lighting or appliances connected to socket-outlets.

Individual light settings, whenever and wherever you want. in the living room, dining room, for reading or while watching TV. Easy to save and to activate. By remote control, for example, via touchscreen.

If you hear things going bump in the night, just hit the “panic button” next to your bed to illuminate your house and garden with bright light.

Keep burglars at bay by making it look as though someone is at home when you are absent or during long holidays.

Wind sensor

Multi-function push-button, 4-gang with room temperature control unit, frame Merten Artec

��

��

Flexibility and cost efficiency are particularly important when it comes to commercial buildings. This is where intelligent building management with KNX really comes into its own.

In the presentation room, for example: At the touch of a single button, you can activate a whole series of functions in preparation for a presentation: groups of

luminaires are switched off or dimmed, the blinds and the projection screen are lowered to create the right conditions for the presentation, and the projector and microphone are switched on automatically. And finally, ventilation and heating create an optimal environment.

Naturally, all these different functions can be adapted to meet specific requirements.

schneider-electric@home via touchscreen

WorkingmadeeasyKNXincommercialbuildings

Flexible building management:

Flexible adaptation of the building functions when rooms are used for different purposes, e.g. after reorganisation or a move.

Worldwide access to the entire building technology system via PDA, PC or touchscreen.

Monitoring of windows and doors or underground car parks by sensors that signal all irregularities.

Display of loads, performance curves and temperatures, immediate notification in the case of critical temperature overshoots and automatic shutdown of devices at risk.

Display of fault signals and automatic forwarding of these signals to the responsible electrician or the building manager.

Costly peak loads avoided since loads can be switched on and off in a systematic fashion.

Automatic lighting control:

Time-dependent, automatic switching off of light sources during work breaks or on weekends.

Daylight-dependent adaptation of the lighting for optimum working conditions through light control. With intelligent heating control, energy costs can be reduced by up to 30%.

Automatic lighting of corridors, staircase timers and rooms which are seldom used thanks to the ARGUS indoor movement detector.

Intelligent blind control:

Automatic control of the sun awnings via light sensors in accordance with the current sunlight intensity.

Automatic blind retraction via wind sensors during strong wind.

Automatic adjustment of the blind slats in accordance with the current sunlight intensity.

Individual heating control:

Presence-dependent room heating.

Immediate closure of the heating valve when a window is opened.

Heat is supplied automatically at the exact time required and individually via controllable room temperature control units. No need to turn the radiators up and down manually.

ARGUS Presence with lighting control

Push-button, 4-gang, Merten System M

ARGUS 180/2,20M UP, Merten System M

Multi-function push-button, 2-gang with room temperature control unit, frame Merten Artec

��

The central idea of a standard for home automation and building control across different manufacturers was fundamentally moulded by Schneider Electric. Schneider Electric is one of the driving forces behind innovation and technology in building system technology. An initial complete product palette was already available in 1991. Nowadays, the Schneider Electric product range covers a full range of switch cabinet components in addition to design- and

function-oriented control interfaces and sensors: universal dimming actuators, blind actuators, switch actuators, power supplies, binary inputs, gateways etc.

Further information about the worldwide standard for KNX building system technology can be obtained from the home page of the KNX Association (www.konnex.org).

AllbuildingsaremadeintelligentwithKNXKNXTechnology

KNX – the only worldwide open standard for home automation and building system technology in accordance with EN 50090

EN 50090 – the European norm for electrical installation technology for houses and buildings is based on the KNX standard. KNX is the only protocol that meets this norm.

The success story of KNX in numbers:

103 member companies

Represented in 70 countries

Over 21,000 ETS users

100 training centres

40 partners from science and further education

Facts and figures which give you the security of investing in an established, future-oriented technology.

KNXunitesfunctionsunderoneroofwhichwerepreviouslycontrolledseparately

��

With conventional electrical installations, you have to determine in advance how and where your building’s switching systems will be installed, before construc-tion even commences. But with KNX from Schneider Electric, you can keep your options open. That’s because everything in the system can be changed or extended at any time – without the usual mess and without laying new cables.

In addition, all building technology devices and installations are connected via a single bus line. The bus line is laid in parallel to the 230 V power supply. When you activate a sensor (for example, a push-button), an actuator (e.g. the roller shutter control) will carry out all the switching commands required.

Simple,intelligent,provenKNXTechnology

Theintelligentsolution:KNX–onesystem,onestandard,manymulti-taskfunctionsfor maximum flexibility

Theconventionalsolution:manyseparatelines,meaning less flexibility

Actuators(command receivers)

Sensors(command givers)

System componentsBus voltage supply

KNX power supply REG-K/160 mAMTN684016

KNX power supply REG-K/160 mA with emergency inputMTN683816


KNX power supply REG-K/320 mA with emergency inputMTN683832


KNX power supply unit REG-K/640 mA with emergency power inputMTN683890

REG emergency power supplyMTN683901

Lead gel batteryMTN668990

Lead gel batteryMTN668991

System coupler

Coupler REG-KMTN680204

KNX Logic module Basic REG-KMTN676090

System accessories

Bus connecting terminalMTN689701

Branch terminal, yellow/whiteMTN689702

Blanking cover Blanking cover

n MTN662319 n MTN662325 n MTN662144 n MTN662119 n MTN662114 n MTN662160

n MTN662219 n MTN662260 n MTN662246

IR remote control Distance 2010MTN570222

KNX Quick selection guide

ISC0��_V�.0_0�_�00�_EN�0

Interfaces/gatewaysData interfaces

Central plate with square opening Central plate with square opening

n MTN296019 n MTN296025 n MTN297914 n MTN297960


USB interface, flush-mountedMTN681799

USB interface REG-KMTN681829

Gateways

TeleController Plus REG-KMTN680790

Handset for TeleControllerMTN660790

KNX DALI gateway REG-K/1/16(64)/64MTN680191

KNX/IP router REG-KMTN680329

Push-buttonPush-buttons System M

Push-button, 1-gang plus Push-button, 2-gang plus



Push-button, 4-gang plus Push-button, 4-gang plus with IR receiver



Labelling sheets for push-buttons Labelling sheets for multi-function push-button with IR receiver

MTN618319 MTN618320 MTN618419 MTN618420

Protective hood for plasterMTN627591

Push-button 2-gang plus with room temperature control unit

n MTN6212-0344 n MTN6212-0319 n MTN6212-0325 n MTN6212-0444 n MTN6212-0419 n MTN6212-0414 n MTN6212-0460



Multi-function push-button, 2-gang with room temperature control unit

n MTN627319 n MTN627325 n MTN623214 n MTN623260Flush-mounted module for multi-function push-button with room temperature control unit

MTN623299

Multi-function push-button, 4-gang with room temperature control unit and IR receiver


MTN623299


��ISC0��_V�.0_0�_�00�_EN

Rocker for 1-gang push-button module Rocker for 1-gang push-button module with 1/0 imprint



Rocker for 1-gang push-button module with up/down arrow imprint

n MTN619419 n MTN619425 n MTN625514 n MTN625560KNX push-button module, 1-gang MTN625199

Rockers for 2-gang push-button module Rockers for 2-gang push-button module with 1/0 and up/down arrow imprint



Rockers for 2-gang push-button module with up/down arrow and 1/0 imprint

Rockers for 2-gang push-button module with up/down arrow imprint



KNX push-button module, 2-gang MTN625299

Push-buttons Artec/Trancent/Antique







Push-button, 4-gang plus with IR receiver



n MTN6212-4044 n MTN6212-4019 n MTN6212-4060 n MTN6212-4146





MTN623299



MTN623299

Protective hood for plasterMTN628091

Labelling sheets for push-button plusMTN617819





n MTN626544 n MTN626519 n MTN626560 n MTN626546KNX push-button module, 1-gang MTN626199


ISC0��_V�.0_0�_�00�_EN��








KNX push-button module, 2-gang MTN626299

Push-button Trancent

Control electronics, 1- to 4-gangMTN623190Bus coupler 2, flush-mounted MTN690299

Glass sensor cover, 1-gangMTN569100 MTN569101



Cover foil for glass sensor coverMTN569190 MTN569290 MTN569390

Trancent frame, 1-gangMTN482160



Push-buttons Altira

KNX push-button 1-gang KNX push-button 2-gang

n ALB45150 n ALB46150 n ALB45151 n ALB46151

KNX 1-gang push-button with IR receiver

n ALB45152 n ALB46152


��ISC0��_V�.0_0�_�00�_EN

Push-buttons Unica


n MGU3.530.18 n MGU3.530.25 n MGU3.531.18 n MGU3.531.25


n MGU3.532.18 n MGU3.532.25




n MGU5.532.18 n MGU5.532.25




n MGU50.532.18 n MGU50.532.25

Push-buttons Unica Top




n MGU3.532.30 n MGU3.532.12




n MGU5.532.30 n MGU5.532.12




n MGU50.532.30 n MGU50.532.12

Binary inputs

Push-button interface, 2-gang plusMTN670802

Push-button interface, 4-gang plusMTN670804

Binary input REG-K/4x10MTN644492



ISC0��_V�.0_0�_�00�_EN��





Movement detectors

KNX ARGUS 220MTN632519 MTN632515 MTN632569

Movement detectors System M, Artec, Trancent, Antique

KNX ARGUS 180, flush-mounted KNX ARGUS 180, flush-mounted



KNX ARGUS 180/2.20 m flush-mounted


Movement detectors Altira

KNX Movement detector 180

n ALB45153 n ALB46153

Movement detectors Unica


n MGU3.533.18 n MGU3.533.25


n MGU5.533.18 n MGU5.533.25


n MGU50.533.18 n MGU50.533.25


��ISC0��_V�.0_0�_�00�_EN

Movement detectors Unica Top


n MGU3.533.30 n MGU3.533.12


n MGU5.533.30 n MGU5.533.12


n MGU50.533.30 n MGU50.533.12

KNX presence detector

KNX ARGUS Presence BasicMTN630719 MTN630760

KNX ARGUS PresenceMTN630819 MTN630860

KNX ARGUS Presence with light control and IR receiverMTN630919 MTN630960

Surface-mounted housing for ARGUS PresenceMTN550619

KNX ARGUS Presence 180/2.20 m flush-mounted


Other sensors

Analogue input REG-K 4-gangMTN682191

Analogue input module REG/4-gang MTN682192

KNX Basic weather stationMTN663990

Mast and corner fastening for KNX Basic weather stationMTN663992

KNX brightness and temperature sensorMTN663991

Weather station REG-K/4-gangMTN682991

Weather combi-sensor DCF-77 MTN663692


ISC0��_V�.0_0�_�00�_EN��

Time switch

Year time switch REG-K/4/324MTN677129

Year time switch REG-K/4/324 DCF-77MTN677029

KNX timer REG-KMTN677290

DCF77 antennaMTN668091

OBELISK softwareMTN615034

Memory chip for year time switchesMTN668092

Switch actuators

Switch actuator, flush-mounted/230/16MTN629993

Switch actuator REG-K/2x230/10 with manual modeMTN649202


Switch actuator REG-K/2x230/16 with manual mode and current detectionMTN647395




Switch actuator REG-K/8x230/6MTN646808





Switch actuator REG-K/12x230/16, with manual modeMTN648493

Switch actuator REG-K/12x230/16 with current detection and manual modeMTN648495


��ISC0��_V�.0_0�_�00�_EN

Blind/switch actuators

Blind/switch actuator REG-K/8x/16x/10 with manual modeMTN649908

Blind / switch actuator REG-K/12x/24x/10 with manual modeMTN649912

Blind actuators

Blind actuator REG-K/2x/10 with manual modeMTN649802

Blind actuator REG-K/4x24/6 with manual modeMTN648704

Blind actuator REG-K/4x/6MTN646704

Roller shutter actuator REG-K/4x/10 with manual modeMTN649704



Dimming actuators/control unitsDimming actuators

Dimming actuator REG-K/2x230/300 WMTN646630

Universal dimming actuator REG-K/230/1000 WMTN649310

Universal dimming actuator REG-K/230/500 WMTN649350

Universal dimming actuator REG-K/2x230/300 WMTN649330



Control units 1-10 V

Control unit 0-10 V REG-K/1-gang with manual modeMTN647091

Control unit 0-10 V REG-K/3-gang with manual modeMTN646991


ISC0��_V�.0_0�_�00�_EN��

Other actuators

Analogue actuator REG-K/4-gang MTN682291

Analogue actuator module REG/4-gangMTN682292

Control and display devices

Devices for display and operation

Touch panel 7”MTN6260-0007

Inner frame set for 7” touch panel

n MTN6270-0119 n MTN6270-0122

Glass frame for 7” touch panel

n MTN6270-3619

Metal frame for 7” touch panelMTN6270-3721 MTN6270-3714

Aluminium frame for 7” touch panelMTN6270-3760 MTN6270-3719 MTN6270-3722

Frame for 7” touch panel

n MTN6270-0019 n MTN6270-0022

Flush-mounted mounting box for IP touch panel 7”MTN6270-0001

Cavity wall mounting box for touch panel 7”MTN6270-0002

USB cover for 7” touch panel

n MTN6270-0219 n MTN6270-0222

IP touch panel 10”

n MTN683090

KNX module for IP touch panelMTN683093

Real glass frame for IP touch panel 10”

n MTN489960

Flush-mounted mounting box for IP touch panel 10” Cavity wall mounting box for IP touch panel 10”

MTN683091 MTN683092


��ISC0��_V�.0_0�_�00�_EN

Room temperature control unitsRoom temperature control unit System M





Multi-function push-button, 2-gang with room temperature control unit, System M


MTN623299

Multi-function push-button, 4-gang with room temperature control unit and IR receiver, System M


MTN623299

Room temperature control unit with display


KNX Room temperature control unit, flush-mounted/PI with 4-gang push-button interface, System M


Remote sensor for room temperature control unit UP/PIMTN616790

Room temperature control unit for properties


Room temperature control unit Artec, Trancent, Antique





Multi-function push-button, 2-gang with room temperature control unit, Artec/Trancent/Antique


MTN623299

Multi-function push-button, 4-gang with room temperature control unit, Artec/Trancent/Antique


MTN623299



KNX Room temperature control unit, flush-mounted/PI with 4-gang push-button interface, Artec/Trancent/Antique


Remote sensor for room temperature control unit UP/PIMTN616790


ISC0��_V�.0_0�_�00�_EN�0

Room temperature control unit Altira

KNX Room temperature control unit with display

n ALB45154 n ALB46154

Room temperature control unit Unica


n MGU3.534.18 n MGU3.534.25


n MGU5.534.18 n MGU5.534.25


n MGU50.534.18 n MGU50.534.25

Room temperature control unit Unica Top


n MGU3.534.30 n MGU3.534.12


n MGU5.534.30 n MGU5.534.12


n MGU50.534.30 n MGU50.534.12

Room temperature control actuator

EMO valve driveMTN639119

EMO valve drive with 2 binary inputsMTN639118

Programming magnetMTN639190

KNX fan coil actuator REG-KMTN645094

Heating actuator REG-K/6x230/0.05 A MTN645129

Thermoelectric valve drive 230 VMTN639125

Thermoelectric valve drive 24 VMTN639126

Valve adapter VA50 for thermoelectric valve drive Valve adapter VA78 for thermoelectric valve drive

MTN639150 MTN639178

Valve adapter VA80 for thermoelectric valve driveMTN639180


��ISC0��_V�.0_0�_�00�_EN

AccessoriesPower supplies

Power supply REG, 24 V DC / 0.4 AMTN693003

Power supply REG, 24 V DC / 1.25 AMTN693004

Power supply REG, AC 24 V/1 AMTN663529


ISC0��_V�.0_0�_�00�_EN��

KNXSystem components

Bus voltage supplyKNX power supply REG-K/160 mA

Version Art. no.

MTN684016

For generating the bus voltage for a line with up to �� bus devices.With integrated choke to decouple the power supply from the bus and a push-button to discon-nect the power and reset the bus devices connected to the line.For installation on DIN rails EN �0��. The bus is connected using a bus connecting terminal; a data rail is not necessary.Mains voltage: AC ��0 - ��0 V, �0-�0 Hz Output voltage: DC �0 V Output current: max. ��0 mA, short-circuit-proof Device width: � TE = approx. �� mmContents: With bus connecting terminal and cable cover.

KNX power supply REG-K/160 mA with emergency input

Version Art. no.

MTN683816

For generating the bus voltage for a line with up to �� bus devices. The emergency power supply REG can be connected in order to buffer the bus voltage.With integrated choke to decouple the power supply from the bus and a push-button to discon-nect the power and reset the bus devices connected to the line.For installation on DIN rails EN �0��. The bus is connected using a bus connecting terminal; a data rail is not necessary.Mains voltage: AC ��0 - ��0 V, �0-�0 Hz Output voltage: DC �0 V Output current: max. ��0 mA, short-circuit-proof Device width: � TE = approx. �� mmAccessories: REG-K emergency power supply, art. no. MTN��0�.Contents: With bus connecting terminal and cable cover.

KNX power supply REG-K/320 mA

Version Art. no.

MTN684032


��ISC0��_V�.0_0�_�00�_EN


KNX power supply REG-K/320 mA with emergency input

Version Art. no.

MTN683832

For generating the bus voltage for a line with up to �� bus devices. The emergency power supply REG can be connected in order to buffer the bus voltage.With integrated choke to decouple the power supply from the bus and a push-button to discon-nect the power and reset the bus devices connected to the line.For installation on DIN rails EN �0��. The bus is connected using a bus connecting terminal; a data rail is not necessary.Mains voltage: AC ��0 - ��0 V, �0-�0 Hz Output voltage: DC �0 V Output current: max. ��0 mA, short-circuit-proof Device width: � TE = approx. �� mmAccessories: REG-K emergency power supply, art. no. MTN��0�.Contents: With bus connecting terminal and cable cover.

KNX power supply REG-K/640 mA

Version Art. no.

MTN684064


KNX power supply unit REG-K/640 mA with emergency power input

Version Art. no.

light grey MTN683890

For generating the bus voltage for a line with up to �� bus devices. The emergency power supply REG can be connected in order to buffer the bus voltage.With integrated choke to decouple the power supply from the bus and a push-button to discon-nect the power and reset the bus devices connected to the line.For installation on DIN rails EN �0��. The bus is connected using a bus connecting terminal; a data rail is not necessary.Mains voltage: AC ��0 - ��0 V, �0-�0 Hz Output voltage: DC �0 V Output current: max. ��0 mA, short-circuit-proof Device width: � modules = approx. �� mmAccessories: REG-K emergency power supply, art. no. MTN��0�.Contents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight


REG emergency power supply

Version Art. no.


To buffer the bus voltage. If a complete mains failure occurs, an external lead gel battery with a voltage of DC �� V (SELV) can be connected to the REG power supply for buffering. The lead gel battery is recharged or maintained in its charged state by integrated charging electronics.A binary input can be connected in order to register the operational statuses (mains voltage, error warning, battery operation).For installation on DIN rails EN �0��. A data rail is not necessary.Mains voltage: AC ��0 - ��0 V, �0-�0 Hz Output to power supply:Output voltage: DC �0 V ±� V Output current:without battery with mains supply max. 300 mA, with battery without mains supply max. ��0 mA Short-circuit current: < �.� A Charging current: max. � A Connections: plug-in screw terminal for main connector, operating state (4-pin, 3 floating con-tacts) and emergency power supply. Plug-in terminal for battery connection (two � mm pins) Device width: � modules = approx. �� mmAccessories: Lead gel battery, art. no. MTN��0. Lead gel battery, art. no. MTN��. Binary input REG-K/�x��, art. no. MTN��. Power supply REG, DC �� V/0.� A, art. no. MTN��00�.Contents: With connecting terminal and cable cover

Lead gel battery

Version Art. no.

�.� Ah MTN668990

Lead gel battery to connect to the emergency input of the power supply ��0 REG-K with bat-tery connection.Nominal voltage: DC �� V Capacity: �.� Ah

Lead gel battery

Version Art. no.

MTN668991

Lead gel battery for connecting to the emergency power supply REG.Nominal voltage: DC �� V Capacity: �� Ah

��ISC0��_V�.0_0�_�00�_EN


System couplerCoupler REG-K

Version Art. no.


For logical connection and electrical isolation of lines and areas. For mounting on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. Contact established with the primary and secondary line via bus connecting terminal.Device width: � modules = approx. �� mmContents: With � bus connecting terminals.

KNX Logic module Basic REG-K

Version Art. no.


In KNX installations, the logic module serves as a logic and control device. It has �0 logic, �0 filter/timer, 8 converter and 12 multiplexer modules. With 3 freely programmable push-buttons and � status LEDs. They can be assigned control and test functions and can be operated on the device.KNX software functions: 10 logic modules (AND, OR, XOR)

Each with up to � binary input objects and an output object. Input and output object inversion. Output disable via gate function. Behaviour of each input object after bus reset. Adjustable sending behaviour.

10 filter and timer modules Binary input objects and an output object with time delays. Binary input object filtering before output. Output disable via gate function. Behaviour of each input object after bus reset. Adjustable sending behaviour.

8 converter modules Conversion of � bit switching telegrams into � bit priority control. Conversion of � bit switching telegrams into � bit value telegrams. Conversion of � bit value telegrams into � bit switching telegrams. Output disable via gate function. Behaviour of each input object after bus reset. Adjustable sending behaviour.

12 multiplexer modules (lighting control)Multiplexer modules are used to selectively control telegrams, e.g. to toggle between single room and total room control for conference rooms with partition walls.

Supported telegram formats by module: � bit, � bit, � bit, � bit , � byte. A module can be used for the � byte format. Telegram forwarding/blocking in one or both directions using the control object. Adjustable gate behaviour. Adjustable control object behaviour. Output disable via gate function. Adjustable sending behaviour. Adjustable sending delay.

Push-button and LED assignment The three push-buttons and the three LEDs can be freely assigned with binary objects. Behaviour per LED. Behaviour per push-button.

Behaviour after bus reset Adjustable module start-up delay after bus voltage recovery.

Device width: �.� module = approx. �� mm

■■■■■

■■■■■

■■■■■■

■■■■■■■■

■■■

■

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight


System accessoriesBus connecting terminal

Version Art. no.

red/dark grey MTN689701

For connecting max. � core pairs to an KNX device, can also be used as a branch terminal.Consists of two interlocked terminal parts in red (“+”) and dark grey (“-”), each with � plug-in terminals. For solid conductors with a diameter of 0.� to 0.� mm.

Branch terminal, yellow/white

Version Art. no.

yellow/white MTN689702

Branch terminal comprising two interlocking terminal parts in yellow and white, each with � plug-in terminals. For solid conductors with a diameter of 0.� to 0.� mm. For wiring the yellow/white cores of the bus cable.

Blanking cover

Version Art. no.

n polar white, glossy

MTN662319

n active white, glossy

MTN662325

n white MTN662144

n polar white MTN662119

n anthracite MTN662114

n aluminium MTN662160

For System M.

Blanking cover

Version Art. no.



n varnished stain-less steel

MTN662246

For Artec, Trancent, Antique.

��ISC0��_V�.0_0�_�00�_EN


IR remote control Distance 2010

Version Art. no.

black MTN570222

�0-channel IR remote control. For the control of all TELE sensor covers, blind push-buttons with IR receiver, presence detectors with IR receiver and KNX devices with IR receivers.Battery: � microcells (IEC LR 0�, AAA) Range: up to �0 mContents: Without battery.

ISC0��_V�.0_0�_�00�_EN��

KNXInterfaces/gateways

Data interfacesCentral plate with square opening Central plate with square opening

Version Art. no. Version Art. no.


MTN296019 n white MTN297844


MTN296025 n polar white MTN297819



n aluminium MTN297960 n stainless steel MTN297846

For System M.for loudspeaker connection inserts or flush-mounted USB interface.

For Artec, Trancent, Antique.for loudspeaker connection inserts or flush-mounted USB interface.

USB interface, flush-mounted

Version Art. no.

MTN681799

For connecting a programming or diagnostics device with a USB�.� or USB� interface to the KNX. For screw mounting in the size �0 installation box. With integrated bus coupler. The device is connected to the bus with a bus connecting terminal. Compatible with ETS �.Mounting depth: �0 mmContents: With bus connecting terminal.

USB interface REG-K

Version Art. no.


For connecting a programming or diagnostics device with a USB�.� or USB� interface to the INSTABUS EIB. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. With integrated bus coupler.Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight


GatewaysTeleController Plus REG-K

Version Art. no.


The TeleController Plus REG-K connects the telephone network with conventional inputs/out-puts and KNX.

Six switch outputs for conventional relays or surge switches. Six connections, in order to show the current switching status of the surge switch. Six signal inputs for break or make contacts. The TeleController can forward incoming signals to selected participants. Up to �0 communication objects for KNX. To control devices or display the statuses. Connection for an alarm acknowledgement key to reset active messages, for example. Connection to functionally switch off the TeleController.

This is controlled using a conventional DTMF telephone or a DTMF hand transmitter. Mes-sages are conveyed by announcements, SMS, e-mail or fax to the selected participants. The corresponding texts can be changed with the handset. The device is operated with a rotary knob and is supported by display texts and announce-ments. The PC software provided enable convenient operation and configuration.With integrated bus coupler. For installation on DIN rails EN �0��. The bus is connected us-ing screw terminals; a data rail is not necessary.Power supply: DC ��-�� V Power consumption: �0 mA at �� V (open circuit), ��0 mA at �� V (max. load) Switch outputs: �, �00 mA at �� V/�� V Alarm outputs: �, �00 mA at �� V/�� V Signal inputs: 6, for floating make or break contacts Telephone: Analogue, CTR ��, line length � m KNX: Screw terminals RS 232: Cable length � m Device width: � modules = approx. �� mmAccessories: Handset, art. no. MTN��0��0.Contents: PC software, connection cable RS ��.

■■■

■■■

Handset for TeleController

Version Art. no.

anthracite MTN660790

Speech output of the various messages can be monitored and changed with the handset.

ISC0��_V�.0_0�_�00�_EN�0


KNX DALI gateway REG-K/1/16(64)/64

Version Art. no.


The DALI gateway connects the KNX with digital electronic ballasts equipped with a DALI interface. The gateway is the DALI master and power supply for the electronic ballasts. It sup-ports the switching and dimming of up to �� electronic ballasts in �� groups and the control of �� lightscenes. In addition, the �� electronic ballasts can be individually activated via KNX or compiled via KNX group addresses.Error messages of individual electronic ballasts or each connected lamp can be transmitted to the KNX and visualised on display devices. DALI commissioning and configuration, as well as group assignment and scene setting can be carried out using:

the device (display and operating buttons) a software tool (free of charge) the integrated Web server. The RH�� connection is used for connection to a PC (with standard browser). a portable Web panel or a PDA

The device has � inputs for connecting push-buttons (building site operation), for example. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The network and the DALI cable as well as the switch inputs are connected via screw terminals on the device.Supply voltage: AC ��0 - ��0 V, �0 - �0 Hz Inputs: �, passive DC � - �� V or AC � - �� V Outputs: DALI D+, D- in line with DALI specification DC 16 - 18 V, 150 mA, short circuit-proof Interfaces: �xRJ�� Connecting cable: �.� - �.� mm² Type of protection: IP �0 Device width: � modules = approx. �0� mmContents: With bus connecting terminal.

■■■

■

KNX/IP router REG-K

Version Art. no.


The KNX/IP router enables telegrams to be forwarded between different lines via LAN (IP) as a rapid backbone. The device can additionally serve as a programming interface in order to connect a PC with the KNX bus (e.g. for ETS programming with suitable ETS).The IP address can be assigned dynamically via a DHCP server or via manual configuration (ETS parameter). The device operates in accordance with the KNXnet/IP specification using Core, device management, tunnelling and routing. The KNX/IP router forwards telegrams in both directions whilst taking a filter table into account and can buffer up to ��0 telegrams. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary.Supply voltage: DC ��-�0 V (at DC �� V �0 mA), AC ��-�� V Device width: � modules = approx. �� mmContents: With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight

KNXPush-button

Push-buttons System MPush-button, 1-gang plus Push-button, 2-gang plus



MTN617119 n polar white, glossy

MTN617219


MTN617125 n active white, glossy

MTN617225

n anthracite MTN627514 n anthracite MTN627614

n aluminium MTN627560 n aluminium MTN627660

For System M.With integrated bus coupling unit. Push-button with � operating buttons, operat-ing and status display and labelling field. The operating display can also be used as an orientation light.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-tons, art. no. MTN��/�0.Contents: With protective hood for plaster. With bus connecting terminal.

For System M.With integrated bus coupling unit. Push-button with four operating buttons, op-erating and status display and labelling field. The operating display can also be used as an orientation light.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-tons, art. no. MTN��/�0.Contents: With protective hood for plaster. With bus connecting terminal.

Labelling sheets for push-buttons Labelling sheets for multi-function push-button with IR receiver


polar white MTN618319 polar white MTN618419

silver MTN618320 silver MTN618420

For individual labelling of the System M push-buttons with text or symbols.Contents: � sheet for every �� products.

For individual labelling of the System M multi-function push-button with IR receiver.Contents: � sheet for every �� products.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight

KNXPush-button

Push-button, 4-gang plus Push-button, 4-gang plus with IR receiver




MTN617519



MTN617525



For System M.With integrated bus coupling unit. Push-button with � operating buttons, operat-ing and status display and labelling field. The operating display can also be used as an orientation light.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-tons, art. no. MTN��/�0.Contents: With protective hood for plaster. With bus connecting terminal.

For System M.With integrated bus coupling unit. Push-button with � operating buttons, operat-ing and status display and labelling field. The operating display can also be used as an orientation light. The functions of each of the keys can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Merten IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons. The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for multi-func-tion push-button with IR receiver, art. no. MTN��/�0.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With protective hood for plaster. With bus connecting terminal.

Protective hood for plaster

Version Art. no.

MTN627591

For System M.To protect push-buttons, rockers, room temperature control units and room controllers from contamination from painting and decorating work.Note: When the protective hood for plaster is in place, the temperature measurement of the room temperature control unit is restricted.

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight

Taha Mallat

Highlight

KNXPush-button


Version Art. no.

n white, glossy MTN6212-0344


MTN6212-0319


MTN6212-0325

n white MTN6212-0444

n polar white MTN6212-0419

n anthracite MTN6212-0414

n aluminium MTN6212-0460

For System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With � red LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:

Heating with one controller output Cooling with one controller output Heating and cooling with separate controller outputs Heating and cooling with one controller output �-step heating with � control outputs �-step cooling with � control outputs �-step heating and cooling with � control outputs

Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Scene function. Operation: Menu.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button


Version Art. no.



MTN6214-0319


MTN6214-0325





For System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control. With � red LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Scene function. Operation: Menu.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button


Version Art. no.


MTN627319


MTN627325



Application module for System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:

Heating with one controller output Cooling with one controller output Heating and cooling with separate controller outputs Heating and cooling with one controller output �-step heating with � control outputs �-step cooling with � control outputs

Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuAccessories: Protective hood for plaster, System M, art. no. MTN��...Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: Screw for protection against dismantling.

■■■■■■

Flush-mounted module for multi-function push-button with room temperature control unit

Version Art. no.

MTN623299

For the connection of multi-function push-buttons with room temperature control unit via an application interface.For screw mounting in the size �0 installation box. Flat design. With LED and push-button for programming.Mounting depth: �0 mmContents: With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button


Version Art. no.


MTN634619


MTN634625



Application module for System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control Distance.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuTransmitter: IR remote control Distance, art. no. MTN��0��.Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: With screw for tamper-proofing, adhesive label, barrier covering the IR receiver.

■■■■■■


Version Art. no.

MTN623299


��ISC0��_V�.0_0�_�00�_EN

KNXPush-button





MTN619319



MTN619325



For System M.The rocker is attached to the �-gang push-button module.Accessories: Protective hood for plaster, System M, art. no. MTN��...



Version Art. no.


MTN619419


MTN619425




KNX push-button module, 1-gang

Version Art. no.

MTN625199

For System M.Push-button module without rocker. With programmable status display.The device is connected to the bus line with a bus connecting terminal. With integrated bus coupler.KNX software functions: The push-buttons can be parameterised either as a pair (dual-sur-face) or individually (single-surface). Single-surface: Switch ON or switch OFF, dimming, scenes. Dual-surface: Switch ON or switch OFF, dimming, scenes, blinds.

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button





MTN619519



MTN619525



For System M.The rockers are attached to the �-gang push-button module.Accessories: Protective hood for plaster, System M, art. no. MTN��...







MTN619719



MTN619725






Version Art. no.

MTN625299

For System M.Push-button module without rockers. With programmable status display.The device is connected to the bus line with a bus connecting terminal. With integrated bus coupler.KNX software functions: The push-buttons can be parameterised either as a pair (dual-sur-face) or individually (single-surface). Single-surface: Switch ON or switch OFF, dimming, scenes. Dual-surface: Switch ON or switch OFF, dimming, scenes, blinds.

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button

Push-buttons Artec/Trancent/AntiquePush-button, 1-gang plus Push-button, 2-gang plus


n white MTN628044 n white MTN628144

n polar white MTN628019 n polar white MTN628119


n stainless steel MTN628046 n stainless steel MTN628146

For Artec, Trancent, Antique.With integrated bus coupling unit. Push-button with two operating buttons, operating display, two blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-ton plus art. no. MTN��.Contents: With protective hood for plaster. With bus connecting terminal.

For Artec, Trancent, Antique.With integrated bus coupling unit. Push-button with four operating buttons, operating display, four blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-ton plus art. no. MTN��.Contents: With protective hood for plaster. With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN�0

KNXPush-button






n stainless steel MTN628246 n stainless steel MTN628346

For Artec, Trancent, Antique.With integrated bus coupling unit. Push-button with six operating buttons, oper-ating display, six blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-ton plus art. no. MTN��.Contents: With protective hood for plaster. With bus connecting terminal.

For Artec, Trancent, Antique.With integrated bus coupling unit. Push-button with eight operating buttons, operating display, eight blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operating key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-but-ton plus art. no. MTN��.Contents: With protective hood for plaster. With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button

Push-button, 4-gang plus with IR receiver

Version Art. no.

n white MTN628444



n stainless steel MTN628446

For Artec, Trancent, Antique.With integrated bus coupling unit. Push-button with eight operating buttons, operating display, eight blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. The lower labelling field can be parameterised as an additional operat-ing key. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. The functions of each of the keys can be triggered using an IR remote control. The push-but-ton is pre-programmed for operation with a Merten IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught to the push-but-tons.The device is connected to the bus line with a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Accessories: Labelling sheets for push-button plus art. no. MTN��.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With protective hood for plaster. With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button


Version Art. no.



MTN6212-4019


n stainless steel MTN6212-4146

For Artec, Trancent, Antique.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With � blue LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:



■■■■■■■

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button


Version Art. no.



MTN6214-4019



For Artec, Trancent, Antique.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control. With � blue LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Scene function.Operation: Menu.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button


Version Art. no.

n white MTN628744




For Artec, Trancent, Antique.Convenient control unit with four operating buttons, operating display, four blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. With room temperature control unit and display.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuAccessories: Protective hood for plaster, Artec, Trancent, Antique, art. no. MTN��0��...Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: Screw for protection against dismantling. With protective hood for plaster.

■■■■■■


Version Art. no.

MTN623299


��ISC0��_V�.0_0�_�00�_EN

KNXPush-button


Version Art. no.

n white MTN628844




For Artec.Convenient control unit with eight operating buttons, operating display, eight blue status dis-plays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control Distance.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuTransmitter: IR remote control Distance, art. no. MTN��0��.Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: With screw for tamper-proofing, adhesive label, barrier covering the IR receiver. With protective hood for plaster.

■■■■■■


Version Art. no.

MTN623299


ISC0��_V�.0_0�_�00�_EN��

KNXPush-button

Protective hood for plaster

Version Art. no.

MTN628091

For Artec, Trancent, Antique.To protect push-buttons, rockers, room temperature control units and room controllers from contamination from painting and decorating work.Note: When the protective hood for plaster is in place, the temperature measurement of the room temperature control unit is restricted.

Labelling sheets for push-button plus

Version Art. no.

MTN617819

For individual labelling of the Artec/Trancent/Antique push-button plus with text or symbols.Contents: � sheet for �0 products.







MTN626146 n varnished stain-less steel

MTN626446

For Artec, Trancent, Antique.The rocker is attached to the �-gang push-button module.Accessories: Protective hood for plas-ter, Artec, Trancent, Antique, art. no. MTN��0��...

For Artec, Trancent, Antique.The rocker is attached to the �-gang push-button module.Accessories: Protective hood for plas-ter, Artec, Trancent, Antique, art. no. MTN��0��...

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button


Version Art. no.

n white MTN626544




MTN626546

For Artec, Trancent, Antique.The rocker is attached to the �-gang push-button module.Accessories: Protective hood for plaster, Artec, Trancent, Antique, art. no. MTN��0��...


Version Art. no.

MTN626199

For Artec, Trancent, Antique.Push-button module without rocker. With programmable status display.The device is connected to the bus line with a bus connecting terminal. With integrated bus coupler.KNX software functions: The push-buttons can be parameterised either as a pair (dual-sur-face) or individually (single-surface). Single-surface: Switch ON or switch OFF, dimming, scenes. Dual-surface: Switch ON or switch OFF, dimming, scenes, blinds.








MTN626646

For Artec, Trancent, Antique.The rockers are attached to the �-gang push-button module.Accessories: Protective hood for plas-ter, Artec, Trancent, Antique, art. no. MTN��0��...


ISC0��_V�.0_0�_�00�_EN��

KNXPush-button









MTN626846




Version Art. no.

MTN626299

For Artec, Trancent, Antique.Push-button module without rockers. With programmable status display. The device is con-nected to the bus line with a bus connecting terminal. With integrated bus coupler.KNX software functions: The push-buttons can be parameterised either as a pair (dual-sur-face) or individually (single-surface). Single-surface: Switch ON or switch OFF, dimming, scenes. Dual-surface: Switch ON or switch OFF, dimming, scenes, blinds.

Push-button TrancentControl electronics, 1- to 4-gang

Version Art. no.

�- to �-gang MTN623190

For the Trancent range. The control electronics can be programmed as a �-, �- or �-gang sensor cover.With orientation LED. Operation of the glass cover is acknowledged with a short tone.KNX software functions: The covers facing each other can either be parameterised as a pair (dual-surface) or as individual buttons (single-surface). There are a total of �� parameterisa-tion options available. Single-surface: dimming, toggling, pulse edges, temperature, scenes. Dual-surface: blind control, switching, dimming, toggling, pulse edges, temperature, scene.Accessories: Cover foil for glass sensor cover, art. no. MTN��0, MTN��0, MTN��0.

Bus coupler 2, flush-mounted

Version Art. no.

MTN690299

For screw mounting in the size �0 installation box. With LED and push-button for program-ming. Mounting depth: �0 mm. Contents: With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button

Glass sensor cover, 1-gang

Version Art. no.

transparent MTN569100

satinated MTN569101

For switching and dimming lighting systems, controlling roller shutters and scenes (KNX).The glass sensor cover reacts to the lightest of touches. Control electronics evaluate the signal and forward it to the switch, dimming or roller shutter insert or bus coupler. Accessories: Cover foil for glass sensor cover, art. no. MTN��0.Contents: With cover foil, �-gang and screws.


Version Art. no.


satinated MTN569201



Version Art. no.


satinated MTN569301


ISC0��_V�.0_0�_�00�_EN�0

KNXPush-button

Cover foil for glass sensor cover

Version Art. no.

for ��00/0� MTN569190

for ��00/0� MTN569290

for ��00/0� MTN569390

For individual labelling of the Trancent glass sensor covers with text or symbols. For laser printersContents: For glass sensor cover, �-gang: � sheet for � products. For glass sensor cover, �-gang: � sheet for � products. For glass sensor cover, �-gang: � sheet for � products.

Trancent frame, 1-gang

Version Art. no.

aluminium MTN482160

For vertical and horizontal installation.


Version Art. no.

aluminium MTN482260



Version Art. no.

aluminium MTN482360


��ISC0��_V�.0_0�_�00�_EN

KNXPush-button

Push-buttons AltiraKNX push-button 1-gang KNX push-button 2-gang


n white ALB45150 n white ALB45151

n aluminium ALB46150 n aluminium ALB46151

� modulesIn Altira design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Altira design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.

n white ALB45152

n aluminium ALB46152

� modulesIn Altira design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button

Push-buttons UnicaKNX push-button 1-gang KNX push-button 2-gang


n white MGU3.530.18 n white MGU3.531.18

n ivory MGU3.530.25 n ivory MGU3.531.25

� modulesIn Unica design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Unica design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.

n white MGU3.532.18

n ivory MGU3.532.25

� modulesIn Unica design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button





� modulesIn Unica design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Unica design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.

n white MGU5.532.18

n ivory MGU5.532.25

� modulesIn Unica design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With fixing frame. With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button





� modulesIn Unica design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame and claws. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Unica design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame and claws. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.

n white MGU50.532.18

n ivory MGU50.532.25

� modulesIn Unica design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With fixing frame and claws. With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button

Push-buttons Unica TopKNX push-button 1-gang KNX push-button 2-gang


n aluminium MGU3.530.30 n aluminium MGU3.531.30

n graphite MGU3.530.12 n graphite MGU3.531.12

� modulesIn Unica Top design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Unica Top design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.

n aluminium MGU3.532.30

n graphite MGU3.532.12

� modulesIn Unica Top design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��

KNXPush-button





� modulesIn Unica Top design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Unica Top design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.



� modulesIn Unica Top design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With fixing frame. With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN

KNXPush-button





� modulesIn Unica Top design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame and claws. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.

� modulesIn Unica Top design.KNX-push-button with � buttons and � blue status LEDs. The status LED is located under the symbol window which can be taken off.With integrated bus coupler. The bus is con-nected using a bus connecting terminal.KNX software functions: Switching, tog-gling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions.Contents: With fixing frame and claws. With set of �0 symbols: �x symbol with light opening, �x symbol “�”, �x symbol “0”, �x symbol for dimming, �x symbol for shutter, �x symbol (neutral). With bus connecting terminal.


Version Art. no.



� modulesIn Unica Top design.KNX-push-button with � buttons, blue status LED and IR receiver. The status LED is located under the symbol window which can be taken off. The functions of each of the button can be triggered using an IR remote control. The push-button is pre-programmed for operation with a Schneider-Electric IR remote control Distance. Many other IR remote controls (e.g. existing TV or CD player remote controls) can be taught into the push-buttons.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Switching, toggling, dimming (single/dual-surface), blind (single/dual-surface), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long opera-tion), �-bit linear regulator, scene retrieval, scene saving, disable functions.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With fixing frame and claws. With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��

KNXBinary inputs

Binary inputsPush-button interface, 2-gang plus

Version Art. no.

polar white MTN670802

Generates an internal signal voltage for connecting two conventional push-buttons or floating contacts, and for connecting two low-current LEDs.The cores are �0 cm long and can be extended to max. �.� m. For installation in a conven-tional �0 mm switch box.KNX software functions: Switching, dimming or controlling blinds via � or � inputs, position values for blind control (�-bit), pulse edges with �-, �-, �-, or �-bit telegrams, differentiation between short and long activation, initialisation telegram, cyclical transmission, pulse edges with �-byte telegrams, �-bit linear regulator, scenes, counter, disable function, break contact/make contact, debounce time. Outputs for connecting control lamps (low-current LEDs) for the status display.For each input/output object type:Contact voltage: < � V (SELV) Contact current: < 0.� mA Output current: max. � mA Max. cable length: �0 cm unshielded, can be extended up to max. �.� m with twisted un-shielded cable. Dimensions: approx. �0x�0.�x��.� mm (LxWxH)

Push-button interface, 4-gang plus

Version Art. no.


Generates an internal signal voltage for connecting four conventional push-buttons or floating contacts, and for connecting four low-current LEDs.The cores are �0 cm long and can be extended to max. �.� m. For installation in a conven-tional �0 mm switch box.KNX software functions: Switching, dimming or controlling blinds via � or � inputs, position values for blind control (�-bit), pulse edges with �-, �-, �-, or �-bit telegrams, differentiation between short and long activation, initialisation telegram, cyclical transmission, pulse edges with �-byte telegrams, �-bit linear regulator, scenes, counter, disable function, break contact/make contact, debounce time. Outputs for connecting control lamps (low-current LEDs) for the status display.For each input/output object type:Contact voltage: < � V (SELV) Contact current: < 0.� mA Output current: max. � mA Max. cable length: �0 cm unshielded, can be extended up to max. �.� m with twisted un-shielded cable. Dimensions: approx. �0x�0.�x��.� mm (LxWxH)

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight

Taha Mallat

Highlight

KNXBinary inputs

Binary input REG-K/4x10

Version Art. no.


For connecting four conventional push-buttons or floating contacts to the KNX. Internally generates a signal voltage SELV, electrically isolated from the bus.With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.KNX software functions: Switching, dimming or blind control via � or � inputs. Positioning values for blind control (�-bit). Pulse edges with �-, �-, �-, or �-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with �-byte telegrams. �-bit linear regulator. Disable function. Break/make contact. Debounce time.Inputs: � Contact voltage: max. �0 V, clocked Contact current: max. � mA, pulsing Cable length: max. �0 m Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


For connecting eight conventional push-buttons or floating contacts to the KNX. Internally generates a signal voltage SELV, electrically isolated from the bus.With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.KNX software functions: Switching, dimming or blind control via � or � inputs. Positioning values for blind control (�-bit). Pulse edges with �-, �-, �-, or �-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with �-byte telegrams. �-bit linear regulator. Disable function. Break/make contact. Debounce time.Inputs: � Contact voltage: max. �0 V, clocked Contact current: max. � mA, pulsing Cable length: max. �0 m Device width: � modules = approx. �0 mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN�0

KNXBinary inputs


Version Art. no.


For connecting four conventional devices with AC/DC �� V outputs to the KNX.With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.KNX software functions: Switching, dimming or blind control via � or � inputs. Positioning values for blind control (�-bit). Pulse edges with �-, �-, �-, or �-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with �-byte telegrams. �-bit linear regulator. Disable function. Break/make contact. Debounce time.Input voltage: AC / DC �� V Inputs: � Input current: DC �� mA (�0 V), AC � mA (�� V) 0 signal: ≤ 5 V 1 signal: ≥ 11 V Cable length: max. �00 m Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


For connecting � conventional devices with AC/DC �� V outputs to KNX.With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.KNX software functions: Switching, dimming or blind control via � or � inputs. Positioning values for blind control (�-bit). Pulse edges with �-, �-, �-, or �-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with �-byte telegrams. �-bit linear regulator. Disable function. Break/make contact. Debounce time.Input voltage: AC/DC ��V Inputs: � Input current: DC approx. �� mA/AC approx. � mA Line length: max. �00 m Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

KNXBinary inputs


Version Art. no.


For connecting four conventional devices with AC ��0 V outputs to the KNX.With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.KNX software functions: Switching, dimming or blind control via � or � inputs. Positioning values for blind control (�-bit). Pulse edges with �-, �-, �-, or �-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with �-byte telegrams. �-bit linear regulator. Disable function. Break/make contact. Debounce time.Input voltage: AC ��0 V, �0-�0Hz Inputs: � Input current: AC �� mA 0 signal: ≤ 40 V 1 signal: ≥ 160 V Cable length: max. �00 m Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


For connecting eight conventional devices with AC ��0 V outputs to the KNX.With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. The input voltage level is displayed at each input with a yellow LED. A green LED indicates that the device is ready for operation once the application has been loaded.KNX software functions: Switching, dimming or blind control via � or � inputs. Positioning values for blind control (�-bit). Pulse edges with �-, �-, �-, or �-bit telegrams. Differentiation between short/long operation. Initialisation telegram. Cyclical sending. Pulse edges with �-byte telegrams. �-bit linear regulator. Disable function. Break/make contact. Debounce time.Input voltage: AC ��0V, �0-�0Hz Inputs: � Input current: AC approx. � mA Line length: max. �00 m Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��

KNXMovement detector

Movement detectorsKNX ARGUS 220

Version Art. no.


dark brazil MTN632515

aluminium MTN632569

KNX movement detector for outdoors. Potentiometers for setting functions are located underneath the cover plate. With integrated bus coupler. A programming magnet is necessary to program the physical address.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Self-adjusting staircase timer. Angle of detection: ��0° Range: max. �� m Number of levels: � Number of zones: �� with �� switching segments Light sensor: infinitely variable from approx. 3 - 1000 lux, ∞ lux (infinite: movement detection is independent of the position of the sensor head) Time: can be set externally from � s to approx. � min. in � levels or via ETS from approx. � s to approx. �� hours Sensitivity: infinitely adjustable Possible settings for sensor head:Wall mounting: �° up, ��° down, ��° left/right, ±��° axial Ceiling mounting: �° up, ��° down, ��° left/right, ±�.�° axial EC directives: Low-voltage guideline ��/��/EEC and EMC directive ��/��/EEC Type of protection: IP ��Accessories: Mounting bracket, art. no. MTN��. Programming magnet, art. no. MTN��0.Contents: With cover plate and segments to limit the area of detection, screws and plugs.

��ISC0��_V�.0_0�_�00�_EN


Movement detectors System M, Artec, Trancent, Antique

KNX ARGUS 180, flush-mounted KNX ARGUS 180, flush-mounted



MTN631619 n white MTN631844


MTN631625 n polar white MTN631819



n aluminium MTN632660 n varnished stain-less steel

MTN631846

For System M.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupling unit. KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation, master, slave, safety pause, disable function. Sensitivity, bright-ness and staircase timer can be set using the ETS or the potentiometer. Self-adjusting staircase timer. Angle of detection: ��0° Range: � m (for mounting height of �.� m) Number of levels: � Number of zones: �� Sensitivity: infinitely adjustable (ETS or potentiometer) Light sensor: infinitely adjustable from ap-prox. �0 to �000 Lux (ETS or potentiometer) Time: adjustable in steps from � s to � min (potentiometer) or adjustable from � s to �� hours (ETS) EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECContents: With bus connecting terminal and supporting plate.

For Artec, Trancent, Antique.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupling unit. KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation, master, slave, safety pause, disable function. Sensitivity, bright-ness and staircase timer can be set using the ETS or the potentiometer. Self-adjusting staircase timer. Angle of detection: ��0° Range: � m (for mounting height of �.� m) Number of levels: � Number of zones: �� Sensitivity: infinitely adjustable (ETS or potentiometer) Light sensor: infinitely adjustable from ap-prox. �0 to �000 Lux (ETS or potentiometer) Time: adjustable in steps from � s to � min (potentiometer) or adjustable from � s to �� hours (ETS) EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECContents: With bus connecting terminal and supporting plate.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight

Taha Mallat

Highlight


KNX ARGUS 180/2.20 m flush-mounted

Version Art. no.


MTN631719


MTN631725



For System M.Indoor movement detector with anti-crawl protection. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupling unit. For wall mounting in a size �0 mounting box, optimal instal-lation at �.� m.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-adjusting staircase timer. Angle of detection: ��0° Range: � m right/left, �� m to the front (for a mounting height of �.�0 m) Mounting height: �.� m or �.� m with half the range Number of levels: � Number of zones: �� Number of movement sensors: �, sector-orientated, adjustable Sensitivity: infinitely adjustable (ETS or potentiometer) Light sensor: infinitely adjustable from approx. 10 to 2000 Lux (ETS or potentiometer) Time: adjustable in steps from � s to � min (potentiometer) or adjustable from � s to �� hours (ETS) EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECContents: With bus connecting terminal and supporting plate. With cover segments to limit the area of detection.

��ISC0��_V�.0_0�_�00�_EN


Movement detectors AltiraKNX Movement detector 180

Version Art. no.

n white ALB45153


� modulesMovement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With bus connecting terminal.

Movement detectors UnicaKNX Movement detector 180

Version Art. no.

n white MGU3.533.18

n ivory MGU3.533.25

� modulesIn Unica design.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��



Version Art. no.

n white MGU5.533.18

n ivory MGU5.533.25

� modulesIn Unica design.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With fixing frame. With bus connecting terminal.


Version Art. no.



� modulesIn Unica design.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With fixing frame and claws. With bus connecting terminal.

��ISC0��_V�.0_0�_�00�_EN


Movement detectors Unica TopKNX Movement detector 180

Version Art. no.



� modulesIn Unica Top design.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With bus connecting terminal.


Version Art. no.



� modulesIn Unica Top design.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With fixing frame. With bus connecting terminal.

ISC0��_V�.0_0�_�00�_EN��



Version Art. no.



� modulesIn Unica Top design.Movement detector for indoors. When a movement is detected, a data telegram defined by the programming is transmitted.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Five movement blocks: up to four functions can be triggered per block. Telegrams: � bit, � byte, � bytes. Normal operation and surveillance operation, master, slave, safety pause, disable function. Sensitivity, brightness and staircase timer can be set using the ETS or the potentiometer. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-ad-justing staircase timer. Angle of detection: ��0° Number of movement sensors: �, sector-orientated, adjustable (ETS) Recommended mounting height: � m to �,� m Range: at �.�� m mounting height: Approx. � m on all sides, adjustable in �0 steps (rotary switch or ETS) Detection brightness: Infinite setting from approx. 10 lux to approx.1000 lux (rotary switch) or from �0 lux to �000 lux (ETS) Overshoot time: Adjustable in � steps from approx. � s to approx. � min (rotary switch) or adjustable from � s to �� hours (ETS) EC guidelines: Low-voltage guideline �00�/��/EEC and EMC guideline �00�/�0�/ECContents: With fixing frame and claws. With bus connecting terminal.

KNX presence detectorKNX ARGUS Presence Basic

Version Art. no.


aluminium MTN630760

Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are trans-mitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightness-dependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS.With integrated bus coupling unit. For ceiling mounting in a size �0 mounting box, optimal installation at �.� m. Can also be mounted to ceilings using the surface mounting housing for ARGUS Presence.KNX software functions: Two movement/presence blocks: up to four functions can be trig-gered per block. Telegrams: � bit, � byte, � bytes. Normal operation (no master/slave), safety pause, disable function. Self-adjusting staircase timer. Actual brightness value: can be specified via the internal and/or an external light sensor.Angle of detection: ��0° Range: a radius of max. � m (at a mounting height of �.�0 m) Number of levels: � Number of zones: �� with �� switching segments Number of movement sensors: � Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECAccessories: Surface-mounted housing for Argus Presence, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate.

��ISC0��_V�.0_0�_�00�_EN


KNX ARGUS Presence

Version Art. no.


aluminium MTN630860

Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are trans-mitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightness-dependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS.With integrated bus coupling unit. For ceiling mounting in a size �0 mounting box, optimal installation at �.� m. Can also be mounted to ceilings using the surface mounting housing for ARGUS Presence.KNX software functions: Five movement/presence blocks: up to four functions can be trig-gered per block. Telegrams: � bit, � byte, � bytes. Normal operation, master, slave, monitoring, safety pause, disable function. Four movement sensors: the sensitivity and range can be set separately for each sensor. Self-adjusting stair-case timer. Actual brightness value: can be detected via the internal and/or an external light sensor. Actual value correction.Angle of detection: ��0° Range: a radius of max. � m (at a mounting height of �.�0 m) Number of levels: � Number of zones: �� with �� switching segments Number of movement sensors: �, separately adjustable Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECAccessories: Surface-mounted housing for Argus Presence, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate.

ISC0��_V�.0_0�_�00�_EN�0

Taha Mallat

Highlight


KNX ARGUS Presence with light control and IR receiver

Version Art. no.


aluminium MTN630960

Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are trans-mitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightness-dependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS. Light control enables the required brightness in a room to be achieved permanently. Dimming and the optional use of a second lighting group maintains a constant brightness. Individual ARGUS Presence configurations can be changed or other KNX devices can be controlled remotely using the IR receiver.With integrated bus coupling unit. For ceiling mounting in a size �0 mounting box, optimal installation at �.� m. Can also be mounted to ceilings using the surface mounting housing for ARGUS Presence.KNX software functions: Five movement/presence blocks: up to four functions can be trig-gered per block. Telegrams: � bit, � byte, � bytes. An additional light control block: brightness can be maintained constant by dimming and an additional adjustable level. IR receiver function. IR configuration: setting the brightness threshold, staircase timer factors or range. Normal operation, master, slave, monitoring, safety pause, disable function. Four movement sensors: the sensitivity and range can be set separately for each sensor. Self-adjusting stair-case timer. Actual brightness value: can be detected via the internal and/or an external light sensor. Actual value correction.Angle of detection: ��0° Range: a radius of max. � m (at a mounting height of �.�0 m) Number of levels: � Number of zones: �� with �� switching segments Number of movement sensors: �, separately adjustable Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX Number of IR channels: 10 for controlling KNX devices, 10 for configuration EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECAccessories: Surface-mounted housing for Argus Presence, art. no. MTN��0��.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate.

Surface-mounted housing for ARGUS Presence

Version Art. no.


The surface-mounted housing for ARGUS Presence devices also allows them to be surface mounted.

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight


KNX ARGUS Presence 180/2.20 m flush-mounted

Version Art. no.


MTN630419


MTN630425



For System M.Presence detection indoors. If KNX ARGUS Presence detects smaller movements in the room, data telegrams are trans-mitted via KNX to control the lighting, blind or heating at the same time. When the lighting is controlled by brightness-dependent movement detection, the device constantly monitors the brightness in the room. If sufficient natural light is at hand, the device switches the artificial light off even if a person is present. The overshoot time can be adjusted using the ETS.With integrated bus coupling unit. For wall mounting in a size �0 mounting box, optimal instal-lation at �.� m. With anti-crawl protection.KNX software functions: Five movement/presence blocks: up to four functions can be trig-gered per block. Telegrams: � bit, � byte, � bytes. Normal operation, master, slave, monitoring, safety pause, disable function. Two movement sensors: the sensitivity and range can be set separately for each sensor. Self-adjusting stair-case timer. Actual brightness value: can be detected via the internal and/or an external light sensor. Actual value correction.Angle of detection: ��0° Range: � m right/left, �� m to the front (for a mounting height of �.�0 m) Mounting height: �.� m or �.� m at half the range Time: adjustable in steps from � s to � min (potentiometer) or adjustable from � s to �� hours (ETS) Number of levels: � Number of zones: �� Number of movement sensors: �, separately adjustable Light sensor: internal light sensor infinitely adjustable from approx. 10 to 2000 Lux (ETS); external light sensor via KNX EC Directives: Low-voltage guideline ��/��/EEC and EMC guideline ��/��/EECContents: With bus connecting terminal and supporting plate. With cover segments to limit the area of detection.

ISC0��_V�.0_0�_�00�_EN��

KNXOther sensors

Other sensorsAnalogue input REG-K 4-gang

Version Art. no.


The analogue input records and processes analogue sensor signals. Up to four analogue sensors can be connected in any combination. In connection with the analogue input module REG/�-gang, � analogue inputs are available, to which the connection is made using the sub-bus. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. Evaluation and limit value processing is performed in the analogue input. With continuity checking of the � ... �0 mA inputs. Auxiliary voltage: AC �� V (+/-�0 %) Analogue inputs: � Current interface: 0 ... �0 mA, � ... �0 mA Voltage interface: 0 ... � V, 0 ... �0 V Outputs: DC �� V, �00 mA Continuity checking: � ... �0 mA Device width: � modules = approx. �� mmAccessories: Analogue input module REG/�-gang, art. no. MTN��. Power supply REG, AC �� V / � A, art. no. MTN��.Contents: With bus connecting terminal and cable cover.

Analogue input module REG/4-gang

Version Art. no.


Extension module to extend weather station REG-K/�-gang and analogue input REG-K/�-gang from � to � analogue outputs. Connections are made using the sub-bus. Up to four analogue sensors can be connected in any combination. For installation on DIN rails EN �00��. Evaluation and limit value processing is performed in the analogue input or weather station. With continuity checking of the � ... �0 mA inputs. Auxiliary voltage: AC �� V (+/-�0 %) Rating: max. � VA Analogue inputs: � Current interface: 0 ... �0 mA, � ... �0 mA Voltage interface: 0 ... � V, 0 ... �0 V (DC) A/D conversion: �� bit Outputs: DC �� V, �00 mA Continuity checking: � ... �0 mA Device width: � modules = approx. �� mmAccessories: Power supply REG, AC �� V / � A, art. no. MTN��.Contents: With sub-bus jumper.

��ISC0��_V�.0_0�_�00�_EN

KNXOther sensors

KNX Basic weather station

Version Art. no.


The KNX Basic weather station records weather data, analyses these and can transmit them to the bus. The device has a wind sensor, precipitation sensor, temperature sensor and bright-ness sensor.

Wind, brightness and temperature are each sent as a �-byte value, rain as �-byte. Wind can be sent either in m/s or km/h. � universal channels for single tasks or logic operations. Four logic functions per channel are possible. � sun protection channels for external blinds/roller shutter control. For example, this makes sun protection for up to three facades possible. Objects for: twilight threshold, brightness threshold, drive control, automatic sun function, teaching, security. Automatic sun protection. Controls the blinds automatically during the day. Teaching object. With this, every brightness threshold can be reset by the touch of a key. Integrated heating for rain sensor.

Suitable for mounting on an outside wall or with optional accessories on a corner or on a mast. With integrated bus coupler. The bus is connected using a bus connecting terminal. An additional AC ��0 V power supply is required for the heating unit.Power supply: AC ��0 V Power consumption: max. �0 mA with bus voltage Power consumption: �0 W with heating Sensors: � Measuring range: - �0 °C to + �� °C Brightness range: � to �00,000 lux Angle of detection: ��0° Type of protection: IP �� per EN �0�� Dimensions: ��0 x ��0 x �� mmAccessories: Mast and corner fastening for KNX Basic weather station, art. no. MTN��.

■

■

■

■■■

Mast and corner fastening for KNX Basic weather station

Version Art. no.

MTN663992

ISC0��_V�.0_0�_�00�_EN��

KNXOther sensors

KNX brightness and temperature sensor

Version Art. no.


The sensor records brightness and temperature and transmits these values to the bus. It has a temperature sensor and a brightness sensor.

� universal channels for single tasks or logic operations. Temperature and brightness threshold in any combination. Sun protection channel for blinds/roller shutter control. Objects for: twilight threshold, brightness threshold, drive control, automatic sun function, teaching, security. Automatic sun protection. Controls the blinds automatically during the day. Teaching object. With this, every brightness threshold can be reset by the touch of a key.

Suitable for mounting on an outside wall. With integrated bus coupler. The bus is connected using a bus connecting terminal.Power consumption: max. ��0 mW Sensors: � Temperature measurement range: - �� °C to + �� °C (±� % or ±� degree) Brightness measurement range: � to �00,000 lux (±�0% or ±� lux) Type of protection: IP �� according to DIN EN �0�� for vertical installation with cover Dimensions: ��0 x �� x �� mm

■

■

■■

��ISC0��_V�.0_0�_�00�_EN

KNXOther sensors

Weather station REG-K/4-gang

Version Art. no.


The weather station records and processes analogue sensor signals such as wind speed, brightness, twilight, precipitation and a DCF-�� signal. Up to four analogue sensors and the DCF-�� weather combi-sensor can be connected in any combination. In connection with the �-gang analogue input module, � analogue inputs are available, to which the connection is made using the sub-bus. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. If DCF-77 weather combi-sensors are used, it is possible to access a pre-configured setting in the software. The measured values are converted by the weather station into � byte / � byte telegrams (EIS �/� value). This enables bus devices (visualisation software, measured value displays) to access the control processes, generate signals or control weather-dependent processes. Programming is performed using the ETS tool for the weather station.

Two limit values per sensor (not for rain) Connection of multiple wind sensors �� signals can be evaluated Evaluation of DCF-�� time signal (date and time) Astro function Logic operation controller for application of limit-value-dependent actions (even external) Shading of individual façade segments Signal monitoring of the combi-sensors with object for the following protective measures Checking the wind signal for conclusiveness with object for the following protective meas-ures Selective façade shading (for � façades) with adjustment of the basic brightness, façade alignment, angle of opening relative to the sun. External objects for intervention in basic brightness, angle of opening and limit values Alarm byte Continuity monitoring with report on the bus

Auxiliary voltage: AC �� V (+/-�0 %) Analogue inputs: � Current interface: 0 ... �0 mA, � ... �0 mA Voltage interface: 0 ... � V, 0 ... �0 V Outputs: DC �� V, �00 mA Device width: � modules = approx. �� mmAccessories: Analogue input module REG/�-gang, art. no. MTN��. Weather combi-sensor/DCF-��, art. no. MTN��. Power supply REG, AC �� V / � A, art. no. MTN��.Contents: With bus connecting terminal and cable cover.

■■■■■■■■■

■

■■■

ISC0��_V�.0_0�_�00�_EN��

KNXOther sensors

Weather combi-sensor DCF-77

Version Art. no.

black MTN663692

The weather combi-sensor includes a wind sensor, precipitation sensor, twilight sensor and three brightness sensors (East, South, West). With integral DCF-�� receiver, antenna rotat-able through ��° and integral heating. Suitable for external installation on a wall or on a mast. The sensor is connected to a weather station REG-K/�-gang.The weather data is evaluated in the weather station. The necessary power supplies are provided by the weather station with connected power supply REG.Power supply: AC �� V (+/- �� %) Power consumption: max. �00 mA (with heating) Sensors: � Wind speed: 1 ... 40 m/s (≤ 0.5 m/s) Brightness: 0 ... ��0 klux (+/- �0 %) Twilight 0 ... ��0 lux Type of protection: IP �� when installed Temperature range: - �0 °C ... + �0 °C (non-icing) Fixing method: Mounting bracket Dimensions: ��0x�00 mm (⌀xH)

Time switchYear time switch REG-K/4/324

Version Art. no.


Quartz-controlled four-channel year time switch. The device can be programmed manually on the device itself or on the PC using the software. With bus coupler. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. After programming on the PC, all switching times are exported to a memory chip available as an accessory, and transmitted from this into one or more time switches.

�� non-volatile switching times for selectable daily, weekly and date commands, impulse commands �x switching operation for holiday/public holidays �0 weekly programs for holidays and public holidays per channel Free formation of channel and weekday blocks Manual switching is possible via preselection and permanent switches Random program can be activated Operation with mains connection possible High reserve power Quarz-controlled Automatic changeover between summer and winter time

KNX software functions: Switching. Dimming. Send time and date. Scene. Priority.Operating voltage: Bus, DC �� V Accuracy: ≤ ±1 s/day Reserve power: �.� years at full operability. Data backup in disconnected state approx. �0 years (EEPROM) Type of protection: IP �0 Device width: � modules = approx. �0� mmAccessories: Obelisk software, art. no. MTN��0��. Memory chip for year time switches, art. no. MTN��0��.

■

■■■■■■■■■

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight

Taha Mallat

Highlight

KNXOther sensors

Year time switch REG-K/4/324 DCF-77

Version Art. no.


�-channel year time switch with power supply unit and integrated DCF receiver. To be com-pleted with the DCF-�� antenna for radio-controlled time synchronisation. Time and date can be issued on the bus. The device can be programmed manually on the device itself or on the PC using the software. With bus coupler. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. After programming on the PC, all switching times are exported to a memory chip available as an accessory, and transmitted from this into one or more time switches.

�� non-volatile switching times for selectable daily, weekly and date commands, impulse commands �x switching operation for holiday/public holidays �0 weekly programs for holidays and public holidays per channel Free formation of channel and weekday blocks Manual switching is possible via preselection and permanent switches Random program can be activated High reserve power Automatic changeover between summer and winter time Automatic time synchronisation with DCF possible

KNX software functions: Switching. Dimming. Send time and date. Scene. Priority.Operating voltage: Bus, DC �� V AC ��0 V ±�0%, �0-�0 Hz for antenna Accuracy: ≤ ±1s/day Reserve power: �.� years at full operability. Data backup in disconnected state approx. �0 years (EEPROM) Type of protection: IP �0 Device width: � modules = approx. �0� mmAccessories: DCF�� antenna, art. no. MTN��0��. Obelisk software, art. no. MTN��0��. Memory chip for year time switches, art. no. MTN��0��.

■

■■■■■■■■

KNX timer REG-K

Version Art. no.


The timer sends time and date to the bus and can be operated with or without a DCF�� antenna.

Automatic changeover between summer and winter time (can be switched off) Own adjustable changeover rule The data can be sent periodically or on request Lithium cell: time stays the same in the event of loss of bus power

Accuracy: � s/day, the application allows additional adjustment Reserve power: �0 years Antenna line length: max. �00 m Type of protection: IP �0 EC directives: Low-voltage guideline ��/��/EEC and EMC directive ��/��/EEC Device width: � modules = approx. �� mmAccessories: DCF�� antenna, art. no. MTN��0��.

■■■■

ISC0��_V�.0_0�_�00�_EN��

KNXOther sensors

DCF77 antenna

Version Art. no.


Antenna for receiving the time by radio signal. The antenna should be connected to a year time switch REG-K/�/�� DCF-��.Type of protection: IP ��Contents: With mounting bracket.

OBELISK software

Version Art. no.

MTN615034

Software for convenient entry of the switching times for the year time switches REG-K/�/�� on a PC. With adapter for the serial interface to load the program to the memory chip.System requirements: IBM-compatible, �� or higher, Windows ��, ��Contents: With adapter and a memory chip.

Memory chip for year time switches

Version Art. no.

MTN668092

EEPROM memory chip for �� switching times for programming the year time switch REG K/�/��. The program which is created with the software is loaded into the memory chip and can then be imported into one or several year time switches.

��ISC0��_V�.0_0�_�00�_EN

KNXSwitch actuators

Switch actuatorsSwitch actuator, flush-mounted/230/16

Version Art. no.


For switching a load via a make contact. With integrated bus coupler and screw terminals. The device is connected to the bus with a bus connecting terminal. The actuator can be built into a 47 mm ceiling socket with hook or a flush-mounted switch box.KNX software functions: Operation as break or make contact, delay functions for each chan-nel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus volt-age failure and recovery, parameterisable download behaviour.Nominal voltage: AC ��0 V, �0-�0 Hz Nominal current: �� A, ohmic load �0 A, cosϕ = 0.� Nominal outputIncandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. �000 VA with parallel compensation Capacitive load: AC ��0 V, max. �0� µFContents: With bus connecting terminal.

Switch actuator REG-K/2x230/10 with manual mode

Version Art. no.


For independent switching of up to � loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-but-ton operation. With integrated bus coupler. For installation on DIN rails EN �00��.Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Operation as break contact/make contact. Programmable behav-iour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel.Power supply: Nominal voltage: AC ��0 V, �0-�0 Hz For each switch output: Nominal current: �0 A, cosϕ = �; �0 A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. �000 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 W, uncompensated AC ��0 V, max. �000 W with parallel compensation Capacitive load: AC ��0 V, max. �0� µF Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN�0

KNXSwitch actuators


Version Art. no.


For independent switching of two loads via make contacts. With integrated bus coupler and screw terminals. For installation on DIN rails EN �00��. The ��0 V switch output can be oper-ated with a manual switch.The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded.KNX software functions: Operation as break or make contact, delay functions for each chan-nel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus volt-age failure and recovery, parameterisable download behaviour.Nominal voltage: AC ��0 V, �0-�0 Hz For each switching contact: Nominal current: �� A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA Capacitive load: AC ��0 V, �� A, max. �00 µF Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Switch actuator REG-K/2x230/16 with manual mode and current detection

Version Art. no.


For independent switching of two loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All ��0 V switch outputs can be operated with manual switches. With integrated bus coupling unit.For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals.KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function.Nominal voltage: AC ��0 V, �0 - �0 Hz Per switching contact: Nominal current: �� A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA, with parallel compensation Capacitive load: AC ��0 V, �� A, max. �00 µF Motor load: AC ��0 V, max. �000 W Current detection load current: Detection range: 0.� A to �� A (sine effective value or DC) Sensing accuracy: +/- �% of the current value at hand (sine) and +/- �00 mA Frequency: �0/�0 Hz Description: �00 mA Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

KNXSwitch actuators


Version Art. no.


For independent switching of up to � loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-but-ton operation. With integrated bus coupler. For installation on DIN rails EN �00��.Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Operation as break contact/make contact. Programmable behav-iour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel.Power supply: Nominal voltage: AC ��0 V, �0-�0 Hz For each switch output: Nominal current: �0 A, cosϕ = �; �0 A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. �000 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps:AC ��0 V, max. ��00 W, uncompensated AC ��0 V, max. �000 W with parallel compensation Capacitive load: AC ��0 V, max. �0� µF Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


For independent switching of four loads via make contacts. With integrated bus coupler � and screw terminals. For installation on DIN rails EN �00��. The ��0 V switch output can be oper-ated with a manual switch.The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded.KNX software functions: Operation as break or make contact, delay functions for each chan-nel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus volt-age failure and recovery, parameterisable download behaviour.Nominal voltage: AC ��0 V, �0-�0 Hz For each switching contact: Nominal current: �� A, cosϕ = 0,� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA Capacitive load: AC ��0 V, �� A, max. �00 µF Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight

KNXSwitch actuators


Version Art. no.


For independent switching of four loads via make contacts. The actuator has integrated cur-rent detection that measures the load current on each channel. All ��0 V switch outputs can be operated with manual switches. With integrated bus coupling unit.For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals.KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function.Nominal voltage: AC ��0 V, �0 - �0 Hz Per switching contact: Nominal current: �� A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA, with parallel compensation Capacitive load: AC ��0 V, �� A, max. �00 µF Motor load: AC ��0 V, max. �000 W Current detection load current: Detection range: 0.� A to �� A (sine effective value or DC) Sensing accuracy: +/- �% of the current value at hand (sine) and +/- �00 mA Frequency: �0/�0 Hz Description: �00 mA Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Switch actuator REG-K/8x230/6

Version Art. no.


For independent switching of eight loads via make contacts. With integrated bus coupler and plug-in screw terminals. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded.KNX software functions: Operation as break or make contact, delay functions for each chan-nel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus volt-age failure and recovery, parameterisable download behaviour.Nominal voltage: AC ��0 V, �0-�0 Hz For each switching contact: Nominal current: � A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. ��0 W Halogen lamps: AC ��0 V, max. ��0 W Fluorescent lamps: AC ��0 V, max. �000 VA Capacitive load: AC ��0 V, � A, max. �0� µF Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

KNXSwitch actuators


Version Art. no.


For independent switching of up to � loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-but-ton operation. With integrated bus coupler. For installation on DIN rails EN �00��.Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Operation as break contact/make contact. Programmable behav-iour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel.Power supply: Nominal voltage: AC ��0 V, �0-�0 Hz For each switch output: Nominal current: �0 A, cosϕ = �; �0 A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. �000 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps:AC ��0 V, max. ��00 W, uncompensated AC ��0 V, max. �000 W with parallel compensation Capacitive load: AC ��0 V, max. �0� µF Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


For independent switching of � loads via make contacts. All ��0 V switch outputs can be operated with manual switches. With integrated bus coupler. For installation on DIN rails EN �00��.The device is connected to the mains via screw terminals; every second L connection is bridged internally. The bus is connected using a bus connecting terminal; a data rail is not nec-essary. A green LED indicates readiness for operation after the application has been loaded.KNX software functions: Operation as break or make contact, delay functions for each chan-nel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus volt-age failure and recovery, parameterisable download behaviour.Nominal voltage: AC ��0 V, �0-�0 Hz Per switch contact: Nominal current: �� A, cosϕ =0.� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA Capacitive load: AC ��0 V, �� A, max. �00 µF Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight

KNXSwitch actuators


Version Art. no.


For independently switching � loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All ��0 V switch outputs can be operated with manual switches. With integrated bus coupling unit.For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals.KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function.Nominal voltage: AC ��0 V, �0 - �0 Hz Per switching contact: Nominal current: �� A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA, with parallel compensation Capacitive load: AC ��0 V, �� A, max. �00 µF Motor load: AC ��0 V, max. �000 W Current detection load current: Detection range: 0.� A to �� A (sine effective value or DC) Sensing accuracy: +/- �% of the current value at hand (sine) and +/- �00 mA Frequency: �0/�0 Hz Description: �00 mA Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


For independent switching of up to �� loads via make contacts. The function of the switching channels is freely configurable. All switching outlets can be operated manually using push-but-ton operation. With integrated bus coupler. For installation on DIN rails EN �00��.Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Operation as break contact/make contact. Programmable behav-iour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel.Power supply: Nominal voltage: AC ��0 V, �0 - �0 Hz External auxiliary voltage (optional): AC ��0 - ��0 V, �0 - �0 Hz, max. � VA For each switch output: Nominal current: �0 A, cosϕ = �; �0 A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. �000 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps:AC ��0 V, max. ��00 W, uncompensated AC ��0 V, max. �000 W parallel-compensated Capacitive load: AC ��0 V, max. �0� µF Device width: � modules = approx. �0� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

KNXSwitch actuators

Switch actuator REG-K/12x230/16, with manual mode

Version Art. no.


For independent switching of �� loads via make contacts. All ��0 V switch outputs can be operated with manual switches. With integrated bus coupler.The device is connected to the mains via screw terminals; every second L connection is bridged internally. For installation on DIN rails EN�00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for opera-tion after the application has been loaded.KNX software functions: Operation as break or make contact, delay functions for each chan-nel, staircase lighting function with/without manual OFF function, cut-out warning for staircase lighting function, blocking and additional logic operation or priority control, scenes, status feedback function per channel, central function, comprehensive parameterisation for bus volt-age failure and recovery, parameterisable download behaviour.Nominal voltage: AC ��0 V, �0-�0 Hz Per switch contact: Nominal current: �� A, cosϕ =0.� Incandescent lamps: AC ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA Capacitive load: AC ��0 V, �� A, max. �00 µF Device width: �� modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Switch actuator REG-K/12x230/16 with current detection and manual mode

Version Art. no.


For independently switching �� loads via make contacts. The actuator has integrated current detection that measures the load current on each channel. All ��0 V switch outputs can be operated with manual switches. With integrated bus coupling unit.For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates that the device is ready for operation once the application has been loaded. The load is connected with screw terminals.KNX software functions: Operation as break contact or make contact. Staircase lighting function with/without manual OFF function and switch-off warning. Delay functions. Scenes. Logic function. Blocking or priority control. Feedback function. Status. Central function with delay. Parameterisation for bus voltage failure and recovery. Behaviour for download. Current detection function: Behaviour when value exceeds/falls short of the threshold value. Energy, operating and switch on counter with limit value monitoring. Flash function.Nominal voltage: AC ��0 V, �0 - �0 Hz Per switching contact:Nominal current: �� A, cosϕ = 0.� Incandescent lamps: A C ��0 V, max. ��00 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps: AC ��0 V, max. ��00 VA, with parallel compensation Capacitive load: AC ��0 V, �� A, max. �00 µF Motor load: AC ��0 V, max. �000 W Current detection load current: Detection range: 0.� A to �� A (sine effective value or DC) Sensing accuracy: +/- �% of the current value at hand (sine) and +/- �00 mA Frequency: �0/�0 Hz Description: �00 mA Device width: �� modules = approx. �� mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight

Taha Mallat

Highlight

KNXBlind/switch actuators

Blind/switch actuatorsBlind/switch actuator REG-K/8x/16x/10 with manual mode

Version Art. no.


For independent control of up to � blind/roller shutter drives or for switching up to �� loads via make contacts. The function of the blind or switching channels is freely configurable. All blind/switch outputs can be operated manually using push-buttons. With integrated bus coupling unit. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Weather alarm. �-bit positioning for height and slats. Scenes. Status and feedback function. Switch actuator functions: Operation as break contact/make contact. Programmable behav-iour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel.Power supply: Nominal voltage: AC ��0 V, �0 - �0 Hz External auxiliary voltage (optional): AC ��0 - ��0 V, �0 - �0 Hz, max. � VA For each blind output:Nominal current: �0 A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W For each switch output: Nominal current: �0 A, cosϕ = �; �0 A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. �000 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps:AC ��0 V, max. ��00 W, uncompensated AC ��0 V, max. �000 W parallel-compensated Capacitive load: AC ��0 V, max. �0� µF Device width: � modules = approx. �� mmNote: The blind actuator/switch actuator cannot be used in conjunction with the weather-de-pendent automatic functions of the weather combi-sensor/DCF�� art. no. MTN��. If you require these functions then use the blind actuators art. no. MTN��...Contents: With bus connecting terminal and cable cover.

Blind / switch actuator REG-K/12x/24x/10 with manual mode

Version Art. no.


For independent control of up to �� blind/roller shutter drives or for switching up to �� loads via make contacts. The function of the blind or switching channels is freely configurable. All blind/switch outputs can be operated manually using push-buttons. With integrated bus cou-pler. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Weather alarm. �-bit positioning for height and slats. Scenes. Status and feedback function. Switch actuator functions: Operation as break contact/make contact. Programmable behav-iour for download. Delay functions for each channel. Staircase lighting function with/without manual OFF function. Cut-out warning for staircase lighting function. Scenes. Central function. Disable function. Logic operation or priority control. Status feedback function for each channel.Power supply: Nominal voltage: AC ��0 V, �0 - �0 Hz External auxiliary voltage (optional): AC ��0 - ��0 V, �0 - �0 Hz, max. � VA For each blind output: Nominal current: �0 A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W For each switch output: Nominal current: �0 A, cosϕ = �; �0 A, cosϕ = 0.� Incandescent lamps: AC ��0 V, max. �000 W Halogen lamps: AC ��0 V, max. ��00 W Fluorescent lamps:AC ��0 V, max. ��00 W, uncompensated AC ��0 V, max. �000 W parallel-compensated Capacitive load: AC ��0 V, max. �0� µF Device width: �� modules = approx. �� mmNote: The blind actuator/switch actuator cannot be used in conjunction with the weather-de-pendent automatic functions of the weather combi-sensor/DCF�� art. no. MTN��. If you require these functions then use the blind actuators art. no. MTN��...Contents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN


Blind actuatorsBlind actuator REG-K/2x/10 with manual mode

Version Art. no.


For independent control of � blind/roller shutter drives. The function of the blind channels is freely configurable. All blind outputs can be operated manually using push-button operation. With integrated bus coupling unit. For installation onto DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Differentiated disable functions and weather alarms. �-bit positioning for height and slat. Scenes. Manual/automatic mode. Differentiated status and status feedback functions.For each blind output: Nominal voltage: AC ��0 V, �0-�0 Hz Nominal current: �0 A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Blind actuator REG-K/4x24/6 with manual mode

Version Art. no.


For independent control of � blind/roller shutter drives. The function of the blind channels is freely configurable. All blind outputs can be operated manually using push-button operation. With integrated bus coupler. For installation onto DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Differentiated disable functions and weather alarms. �-bit positioning for height and slat. Scenes. Manual/automatic mode. Differentiated status and status feedback functions.For each blind output: Nominal voltage: DC �� V ±�0 % Nominal current: � A Load types: �� V direct current drives Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Blind actuator REG-K/4x/6

Version Art. no.


For independent control of � blind/roller shutter drives. With integrated bus coupler and plug-in screw terminals. For installation onto DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. A green LED indicates readiness for operation after the application has been loaded.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Weather alarms. �-bit positioning for height and slats. Scenes. Automatic function. Differenti-ated status and feedback functions.For each blind output: Nominal voltage: AC ��0 V, �0-�0 Hz Nominal current: � A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��


Roller shutter actuator REG-K/4x/10 with manual mode

Version Art. no.


For independent control of � roller shutter drives. The function of the roller shutter channels is freely configurable. All roller shutter outputs can be operated manually using push-button operation. With integrated bus coupler. For installation onto DIN rails EN �00��.Bus connection is via bus terminals, a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Roller shutter functions: Running time. Idle time. Differentiated disable functions and weather alarms. �-bit positioning for height. Scenes. Manual/automatic function. Differentiated status and status feedback functions.For each roller shutter output: Nominal voltage: AC ��0 V, �0-�0 Hz Nominal current: �0 A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Blind actuator REG-K/4x/10 with manual mode

Version Art. no.


For independent control of � blind/roller shutter drives. The functions of the blind channels is freely configurable. All blind outputs can be operated manually using push-button operation. With integrated bus coupling unit. For installation onto DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Differentiated disable functions and weather alarms. �-bit positioning for height and slat. Scenes. Manual/automatic mode. Differentiated status and status feedback functions.For each blind output: Nominal voltage: AC ��0 V, �0-�0 Hz Nominal current: �0 A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Blind actuator REG-K/8x/10 with manual mode

Version Art. no.


For independent control of � blind/roller shutter drives. The functions of the blind channels is freely configurable. All blind outputs can be operated manually using push-buttons. With integrated bus coupler. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary. Channel status display via LEDs. A green LED indicates readiness for operation.KNX software functions: Blind functions: Blind type. Running time. Idle time. Step interval. Differentiated disable functions and weather alarms. �-bit positioning for height and slat. Scenes. Manual/automatic mode. Differentiated status and status feedback functions.For each blind output: Nominal voltage: AC ��0 V, �0 - �0 Hz Nominal current:�0 A, cosϕ = 0.� Motor load: AC ��0 V, max. �000 W External auxiliary voltage (optional): AC ��0-��0 V, �0-�0 Hz, max. � VA Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

KNXDimming actuators/control units

Dimming actuatorsDimming actuator REG-K/2x230/300 W

Version Art. no.


AC ��0 V, �0 HzFor switching and dimming incandescent lamps and dimmable, wound transformers (ohmic / inductive load). (Phase control) With integral bus coupler, plug-in screw terminals, short-circuit and overload protection and soft start function to protect the lamps. For installation onto DIN rails EN �00��.Bus connection is via bus terminals, a data rail is not necessary. Readiness for operation is indicated by a green LED after the application has been loaded, and an overload of one chan-nel or both channels is indicated by a flashing light.KNX software functions: Starting behaviour, memory function, dimming speed, switching off by relative dimming, configurable minimum brightness and behaviour on bus voltage failure/re-covery are programmable.Nominal voltage: AC ��0 V, �0 Hz Nominal power/channel: max. �00 W/VA Minimum load: �� W/VA Short-circuit protection: via fuse Device width: � modules = approx. �0� mmContents: With bus connecting terminal and cable cover.

Universal dimming actuator REG-K/230/1000 W

Version Art. no.


AC ��0 V, �0-�0 HzFor switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, short-circuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN �00��.The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of induc-tive and capacitive loads must not be connected. Bus connection is via bus terminals; a data rail is not necessary.KNX software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery.Nominal voltage: AC ��0 - ��0 V, �0/�0 Hz Nominal power: max. �000 W/VA �0 W minimum load (ohmic) �0 VA minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC ��0 V, �0/�0 Hz (same phase as the dimming channel) Device width: � modules = approx. �� mmExtension unit operation: With mechanical push-buttons (make contact). With TELE insert extension, art. No. MTN��.Contents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN�0


Universal dimming actuator REG-K/230/500 W

Version Art. no.


AC ��0 V, �0-�0 HzFor switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, short-circuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN �00��.The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of induc-tive and capacitive loads must not be connected. Bus connection is via bus terminals; a data rail is not necessary.KNX software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery.Nominal voltage: AC ��0 - ��0 V, �0/�0 Hz Nominal power/channel: max. �00 W/VA �0 W minimum load (ohmic) �0 VA minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC ��0 V, �0/�0 Hz (same phase as the dimming channel) Device width: � modules = approx. �� mmExtension unit operation: With mechanical push-buttons (make contact). With TELE insert extension, art. No. MTN��.Contents: With bus connecting terminal and cable cover.

Universal dimming actuator REG-K/2x230/300 W

Version Art. no.


AC ��0 V, �0-�0 HzFor switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, short-circuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN �00��. The dimming ac-tuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of inductive and capacitive loads must not be connected. Bus connection is via bus terminals; a data rail is not necessary.KNX software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery.Nominal voltage: AC ��0 - ��0 V, �0/�0 Hz Nominal power/channel: max. �00 W/VA �0 W minimum load (ohmic) �0 W minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC ��0 V, �0/�0 Hz (same phase as the dimming chan-nels) Device width: � modules = approx. �� mmExtension unit operation: With mechanical push-buttons (make contact). With TELE insert extension, art. No. MTN��.Contents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN



Version Art. no.


AC ��0 V, �0-�0 HzFor switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers (Automatic load detection). (Phase control and phase alignment)The connection of different outer conductors is allowed.With integral bus coupler, screw terminals, short-circuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN �00��. The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of induc-tive and capacitive loads must not be connected. Bus connection is via bus terminals; a data rail is not necessary.KNX software functions: Dimming operation via KNX, Dimming operation on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback.Nominal voltage: AC ��0 - ��0 V, �0/�0 Hz Channels: � (different phases possible) Nominal power: � x ��0 W/VA � channels: � x �00 W/VA and � x ��0 W/VA � channels: � x �00 W/VA Minimum load/channel: �� W (ohmic) �0 VA (ohmic-inductive/ohmic-capacitive) Device width: � HP = approx. �� mmContents: With bus connecting terminal and cable cover.


Version Art. no.


AC ��0 V, �0-�0 HzFor switching and dimming incandescent lamps, HV halogen lamps and LV halogen lamps using dimmable wound transformers or electronic transformers. (Phase control and phase alignment) With integral bus coupler, screw terminals, short-circuit, open-circuit and excess temperature protection with soft start function. For installation onto DIN rails EN �00��. The dimming actuator automatically recognises the connected load. Combinations of ohmic and inductive, or ohmic and capacitive loads can also be connected. Combinations of induc-tive and capacitive loads must not be connected. Bus connection is via bus terminals; a data rail is not necessary.KNX software functions: Dimming operation via EIB, extension units and on the device, different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery.Nominal voltage: AC ��0 - ��0 V, �0/�0 Hz Nominal power/channel: max. ��0 W/VA �0 W minimum load (ohmic) �0 VA minimum load (ohmic/inductive/capacitive) Input (extension unit operation): AC ��0 V, �0/�0 Hz (same phase as the dimming chan-nels) Device width: � modules = approx. �0� mmExtension unit operation: With mechanical push-buttons (make contact). With TELE insert extension, art. No. MTN��.Contents: With bus connecting terminal and cable cover.

ISC0��_V�.0_0�_�00�_EN��


Control units 1-10 VControl unit 0-10 V REG-K/1-gang with manual mode

Version Art. no.


For connecting devices with 0-�0 V interface to KNX. With integrated bus coupler and screw terminals (��0 V) or plug-in screw terminals (0-�0 V). The ��0 V switch output can be oper-ated with a manual switch. For installation onto DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary.KNX software functions: Different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery.Switch contact: for switching the electronic ballasts/transformers Switching voltage: AC ��0 V Switching current:�� A, cosϕ = 0.� Switching capacity: AC ��0 V, ��00 W, cosϕ = � Capacitive load: AC ��0 V, ��00 W, �00 µF Halogen lamps: AC ��0 V, ��00 W Fluorescent lamps:AC ��0 V, max. �000 W, uncompensated AC ��0 V, max. ��00 VA, with parallel compensation 0-10 V interface: for dimming the electronic ballasts/transformers Voltage range: DC 0-�0 V Device width: �.� modules = approx. �� mmContents: With bus connecting terminal and cable cover.

Control unit 0-10 V REG-K/3-gang with manual mode

Version Art. no.


For connecting devices with 0-�0 V interface to KNX. With integrated bus coupler and screw terminals (��0 V) or plug-in screw terminals (0-�0 V). Each individual ��0 V switch output can be operated manually with a manual switch. For installation onto DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary.KNX software functions: Different dimming curves and dimming speeds, the same dimming time, memory function, ON/OFF delay, staircase time function with/without manual OFF function, scenes (up to eight stored brightness values can be retrieved), central function, logic operation or priority control, blocking function, status feedback, behaviour on bus voltage recovery.Switch contact: for switching the electronic ballasts/transformers Switching voltage: AC ��0 V Switching current:�� A, cosϕ = 0.� Switching capacity: AC ��0 V, ��00 W, cosϕ = � Capacitive load: AC ��0 V, ��00 W, �00 µF Halogen lamps: AC ��0 V, ��00 W Fluorescent lamps:AC ��0 V, max. �000 W, uncompensated AC ��0 V, max. ��00 VA, with parallel compensation 0-10 V interface: for dimming the electronic ballasts/transformers Voltage range: DC 0-�0 V Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN

Taha Mallat

Highlight

Taha Mallat

Highlight


Other actuatorsAnalogue actuator REG-K/4-gang

Version Art. no.


The output channels can be parameterised for different current and voltage signals to control different analogue variables (e.g. servomotors). The actuator has four analogue outputs. For use in connection with the analogue actuator module REG/�-gang, � analogue outputs are provided. Connections are made using the sub-bus. For installation on DIN rails EN �00��. The bus is connected using a bus connecting terminal; a data rail is not necessary. With continuity checking of the current outputs.Auxiliary voltage: AC �� V (+/-�0 %) Analogue outputs: � Current signals: 0 ... �0 mA, � ... �0 mA Voltage signals: 0 ... � V, 0.. �0 V Continuity checking: � ... �0 mA Outputs: DC �� V, �00 mA (total) Device width: � modules = approx. �� mmAccessories: Analogue actuator module REG/�-gang, art. no. MTN��. Power supply REG, AC �� V / � A, art. no. MTN��.Contents: With bus connecting terminal and cable cover.

Analogue actuator module REG/4-gang

Version Art. no.


Extension module to extend analogue actuator REG-K/�-gang from � to � analogue outputs. Connections are made using the sub-bus. The output channels can be independently parameterised for different current and voltage signals to control different control values (e.g. servomotors). For installation on DIN rails EN �00��. Auxiliary voltage: AC �� V (+/-�0 %) Analogue outputs: � Current signals: 0 ... �0 mA, � ... �0 mA Voltage signals: 0 ... � V, 0.. �0 V (DC) Continuity checking: � ... �0 mA Outputs: DC �� V, �00 mA (total) Device width: � modules = approx. �� mmAccessories: Power supply REG, AC �� V / � A, art. no. MTN��.Contents: With sub-bus jumper.

ISC0��_V�.0_0�_�00�_EN��

KNXControl and display devices

Control and display devicesTouch panel 7”

Version Art. no.

MTN6260-0007

The �” touch panel is used for the visualisation and control of current building states and functions. The integrated visualisation software with the self-explanatory user interface offers a high level of operating convenience when operating the touch-sensitive TFT display.Windows CE.NET is installed as the operating system. Further functions:

Real-time week time switch with internet time synchronisation Presence simulation (recording and play-back of switching habits) Alarm management Internet access Load a slide show Automatic standby switching Password protection Adjustable user interface

The �” touch panel has a LAN (�0/�00 Mbit/s), KNX and USB interface. With integrated loudspeaker.Due to its flat design in a flush-mounted housing, its uses range from residential to commercial applications. It can be installed horizontally or vertically.KNX software functions: Switching, dimming, operation of sunshade systems such as roller shutters, awnings and blinds. Save and retrieve scenes Transmit values. Telegram status display. Temperature display. Logic functions. Disable module. Dynamic language selection via KNX object.Nominal voltage: AC ��/��0 V , �0 Hz Power consumption: � W in energy-saving mode, � W when in operation Ambient operating temperature: -�°C to �� °C Display size: ��.� cm (�“) Resolution: �00 x ��0 pixels Display type: TFT Colours shown: ��.000 Hardware: �� MHz Intel XScale PXA��0 RAM: �� MB Flash memory: �� MB Type of protection: IP �0 Dimensions: ��x��x�� mm (HxWxD)In KNX, to be completed with: Inner frame set for �” touch panel, art. no.MTN��0-0�... Frame for �” touch panel, art. no. MTN��0-00.., MTN��0-��.., MTN��0-��...

■■■■■■■■

Inner frame set for 7” touch panel

Version Art. no.


n black MTN6270-0122

The set consists of the inner frame and the USB cover. The design frames, which are avail-able in various types of material, are attached to the touch panel using the inner frame.Dimensions: �0�x��x�.� mm (HxWxD)In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�. Frame for �” touch panel, art. no. MTN��0-00.., MTN��0-��.., MTN��0-��...Replacement part: USB cover for �” touch panel, art. no. MTN��0-0�...

��ISC0��_V�.0_0�_�00�_EN


Glass frame for 7” touch panel

Version Art. no.

n Brilliant white MTN6270-3619

Decorative glass frame for �” touch panel.In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�. Inner frame set for �” touch panel, art. no.MTN��0-0�...

Metal frame for 7” touch panel

Version Art. no.

Brass MTN6270-3721

Steel MTN6270-3714

Decorative solid metal frame for �” touch panel.In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�. Inner frame set for �” touch panel, art. no.MTN��0-0�...

Aluminium frame for 7” touch panel

Version Art. no.

aluminium MTN6270-3760

Polar white MTN6270-3719

Black MTN6270-3722

Decorative aluminium frame for �” touch panel.In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�. Inner frame set for �” touch panel, art. no.MTN��0-0�...

Frame for 7” touch panel

Version Art. no.



Decorative frame for �” touch panel.In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�. Inner frame set for �” touch panel, art. no.MTN��0-0�...

ISC0��_V�.0_0�_�00�_EN��


Flush-mounted mounting box for IP touch panel 7”

Version Art. no.

grey MTN6270-0001

For flush-mounted installation of the touch panel 7”.DimensionsOuter dimensions: ��x��x�� mm (HxWxD)In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�.

Cavity wall mounting box for touch panel 7”

Version Art. no.

MTN6270-0002

For installing the �” touch panel into a cavity wall.DimensionsOuter dimensions: �0�x��x�� mm (HxWxD) Opening: ��x��x�� mm (HxWxD)In KNX, to be completed with: �” touch panel, art. no. MEG��0-000�.

USB cover for 7” touch panel

Version Art. no.



For inserting into the intermediate frame. The USB cover is required as a spare part when damaged or lost.

��ISC0��_V�.0_0�_�00�_EN


IP touch panel 10”

Version Art. no.

n aluminium glossy

MTN683090

The IP touch panel �0” is used for the visualisation and control of current building statuses and functions. It is operated interactively on the touch-sensitive TFT display. Windows CE is installed as the operating system. With this standard, solutions such as data management, web functions and client/server and network functions can be configured quickly and easily. Using the optional visualisation software, the IP touch panel �0” can be programmed for the visualised, interactive control of building functions. The IP touch panel �0” has LAN (�0/�00 Mbit/s), and a RS �� and USB connection. The USB connection is in the front behind the frame. A plug-in KNX module can be used to con-nect the IP touch panel �0” to the KNX.Due to its flat design in a flush-mounted housing, its uses range from home applications to purpose-built applications.KNX software functions: Configuration using the “TP VISU configuration tool”.Display size: �0.�” (��.� cm) Resolution: �00 x �00 pixels, SVGA Display type: TFT, resistive touch Colours shown: > ��000 Mains voltage: DC �� V Power consumption: < �0 W RAM: �� MB Data buffering: via battery Ambient operating temperature: �°C bis �0°C Type of protection: IP �0 Frame dimensions: ��.�x��.�x�� mm (HxWxD) Opening: ��.�x��0.� mm (HxW)Accessories: KNX EIB module for IP touch panel art. no. MTN��0��. Design frame for IP touch panel �0” art. no. MTN��0. Flush-mounted mounting box for IP touch panel �0” art. no. MTN��0��. Cavity wall mounting box for IP touch panel �0” art. no. MTN��0��.Note: The configuration software is available on the Internet.Contents: With Design M-Plan frames, aluminium.

KNX module for IP touch panel

Version Art. no.

MTN683093

Plug-in module for connecting the IP touch panel to the KNX.

Real glass frame for IP touch panel 10”

Version Art. no.

n Diamond silver MTN489960

For M-Plan.Decorative frame for the IP touch panel �0”.Dimensions: ��.�x��.�x��.� mm (HxWxD)

ISC0��_V�.0_0�_�00�_EN��


Flush-mounted mounting box for IP touch panel 10”

Cavity wall mounting box for IP touch panel 10”


MTN683091 MTN683092

For flush-mounted installation of the IP touch panel �0”.Dimensions: �0�x��x�� mm (HxWxD)

For installing the IP touch panel �0” into a cavity wall.Dimensions: �0�x��x�� mm (HxWxD)

��ISC0��_V�.0_0�_�00�_EN

KNXRoom temperature control units

Room temperature control unit System MPush-button 2-gang plus with room temperature control unit

Version Art. no.



MTN6212-0319


MTN6212-0325





For System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display.With � red LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:



■■■■■■■

ISC0��_V�.0_0�_�00�_EN�00



Version Art. no.



MTN6214-0319


MTN6214-0325





For System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control.With � red LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Scene function. Operation: Menu.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

�0�ISC0��_V�.0_0�_�00�_EN



Version Art. no.


MTN627319


MTN627325



Application module for System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuAccessories: Protective hood for plaster, System M, art. no. MTN��...Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: Screw for protection against dismantling.

■■■■■■


Version Art. no.

MTN623299


ISC0��_V�.0_0�_�00�_EN�0�



Version Art. no.


MTN634619


MTN634625



Application module for System M.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control Distance.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuTransmitter: IR remote control Distance, art. no. MTN��0��.Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: With screw for tamper-proofing, adhesive label, barrier covering the IR receiver.

■■■■■■


Version Art. no.

MTN623299


�0�ISC0��_V�.0_0�_�00�_EN



Version Art. no.



MTN6241-0319


MTN6241-0325





For System M.KNX Room temperature control unit with display, labelling field, operation and status LED. The � buttons allow to shift set values and change operation modes.With � red LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the room temperature control unit: Controller type: �-step control, continuous PI controller, switching PI controller (PWM) Output: continuous in the range 0 to �00% or switching ON/OFF Controller mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protection Move all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM. Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons: Selection of �- � operating modes each push-button. Move setpoint.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN�0�


KNX Room temperature control unit, flush-mounted/PI with 4-gang push-button inter-face

Version Art. no.


MTN616719


MTN616725



For System M.The device is a room temperature control unit and a binary input. Depending on the operating mode, the current temperature setpoint value and the room temperature, a control value for the heating or cooling control unit is transmitted to the KNX. The temperature can either be recorded by the internal or the external temperature sensor which must be connected to the push-button interface. The push-button interface generates an internal signal voltage for connecting max. four conventional push-buttons or floating contacts. Of these, two inputs can be used to connect low current LEDs.KNX software functions: Functions of the room temperature control unit:Controller type: �-step control, continuous PI control, switching PI control (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: Setpoint adjustment can be parameterised in the range with adjusting wheel; pres-ence push-button functions can be parameterised/switched offValve protection, controller disable Push-button interface functions:Switching, dimming, external blinds, valuator (dimming valuator, extension unit for light scenes with/without memory function, temperature valuator, brightness valuator).Push-button interface: up to � inputs, � of which can be used as outputs and one for con-necting the remote sensor. Output voltage: � V (SELV) Output current: max. 0.� mA Max. cable length: Inputs/outputs max. � m, remote sensor max. �0 mAccessories: Remote sensor for KNX room temperature control unit, UP/PI art. no. MTN��0.

■■■■■■

Remote sensor for room temperature control unit UP/PI

Version Art. no.

black MTN616790

Temperature sensor the floor/room temperature measurementCable length: � m (� x 0.�� mm�)

�0�ISC0��_V�.0_0�_�00�_EN


Room temperature control unit for properties

Version Art. no.



MTN6221-0319


MTN6221-0325





For System M.KNX room temperature control unit for properties with integrated bus coupler. Depending on the operating mode, the current temperature setpoint value and the actual room temperature, a control value for the heating or cooling control unit is transmitted to the KNX. The tempera-ture can optionally be measured by the internal or by an external bus temperature sensor.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. Operating mode, nominal value, control function settings made only via the bus The device does not have any operating and display elements.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Operation: only via bus telegrams.Contents: With bus connecting terminal and supporting plate. With protective hood for plaster.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN�0�


Room temperature control unit Artec, Trancent, Antique


Version Art. no.



MTN6212-4019



For Artec, Trancent, Antique.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display.With � blue LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:



■■■■■■■

�0�ISC0��_V�.0_0�_�00�_EN



Version Art. no.



MTN6214-4019



For Artec, Trancent, Antique.Convenient control unit with � operating buttons, operating and status display and labelling field. The operating display can also be used as an orientation light. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control.With � blue LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the push-buttons: Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, notification functions, the cyclic reading of external temperature values, fan control, operating modes, move setpoints.Functions of the room temperature control unit: Controller type: �-step control, continuous PI controller, switching PI controller (PWM) Output: continuous in the range 0 to �00% or switching ON/OFF Controller mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protection Move all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM. Monitoring function for the actual temperature, valve protection function. Scene function. Operation: Menu.Transmitter: IR remote control Distance, art. no. MTN��0��.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN�0�



Version Art. no.

n white MTN628744




For Artec, Trancent, Antique.Convenient control unit with four operating buttons, operating display, four blue status displays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. With room temperature control unit and display.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuAccessories: Protective hood for plaster, Artec, Trancent, Antique, art. no. MTN��0��...Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: Screw for protection against dismantling. With protective hood for plaster.

■■■■■■


Version Art. no.

MTN623299


�0�ISC0��_V�.0_0�_�00�_EN



Version Art. no.

n white MTN628844




For Artec.Convenient control unit with eight operating buttons, operating display, eight blue status dis-plays which can be triggered separately, and a labelling field. The blue operating display can also be used as an orientation sign. With room temperature control unit and display. With integrated piezoelectric buzzer to display alarm states and IR receiver. All functions of the respective buttons can be controlled via IR remote control Distance.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day, display mode, time, switching times and brightness. The push-buttons are freely parameterisable as push-button pairs (dual-surface) or as single push-buttons. KNX software functions: Functions of the multi-function push-button:Switching, toggling, dimming, blind control (relative or absolute), pulse edges trigger �-, �- or �-bit telegrams (distinction between short and long operation), pulse edges with �-byte telegrams (distinction between short and long operation), �-bit linear regulator, scene retrieval, scene saving, disable functions, timed control with synchronisation, alarm functions, .the cyclic reading of external temperature values, fan control.Functions of the room temperature control unit:Type of controller: �-step control, continuous PI control, switching PI control (PWM)Output: Continuous in the range 0..�00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: MenuTransmitter: IR remote control Distance, art. no. MTN��0��.Note: Use to label conventional foils (max. thickness 0.� mm). For each device only one flat size 60 mounting box and one flush-mounted module are required.Contents: With screw for tamper-proofing, adhesive label, barrier covering the IR receiver. With protective hood for plaster.

■■■■■■


Version Art. no.

MTN623299


ISC0��_V�.0_0�_�00�_EN��0



Version Art. no.



MTN6241-4019



For Artec, Trancent, Antique.KNX Room temperature control unit with display, labelling field, operation and status LED. The � buttons allow to shift set values and change operation modes.With � blue LEDs.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the room temperature control unit: Controller type: �-step control, continuous PI controller, switching PI controller (PWM) Output: continuous in the range 0 to �00% or switching ON/OFF Controller mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protection Move all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM. Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons: Selection of �- � operating modes each push-button. Move setpoint.Contents: With bus connecting terminal and supporting plate. Screw for protection against dismantling. With protective hood for plaster.

■■■■■■■

��ISC0��_V�.0_0�_�00�_EN


KNX Room temperature control unit, flush-mounted/PI with 4-gang push-button inter-face

Version Art. no.

n white MTN616944




MTN616946

For Artec, Trancent, Antique.The device is a room temperature control unit and a binary input. Depending on the operating mode, the current temperature setpoint value and the room temperature, a control value for the heating or cooling control unit is transmitted to the KNX. The temperature can either be recorded by the internal or the external temperature sensor which must be connected to the push-button interface. The push-button interface generates an internal signal voltage for connecting max. four conventional push-buttons or floating contacts. Of these, two inputs can be used to connect low current LEDs.KNX software functions: Functions of the room temperature control unit:Controller type: �-step control, continuous PI control, switching PI control (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: comfort, comfort extension, standby, night economy, frost/heat protectionOperation: Setpoint adjustment can be parameterised in the range with adjusting wheel; pres-ence push-button functions can be parameterised/switched offValve protection, controller disable Push-button interface functions:Switching, dimming, external blinds, valuator (dimming valuator, extension unit for light scenes with/without memory function, temperature valuator, brightness valuator).Push-button interface: up to � inputs, � of which can be used as outputs and one for con-necting the remote sensor. Output voltage: � V (SELV) Output current: max. 0.� mA Max. cable length: Inputs/outputs max. � m, remote sensor max. �0 mAccessories: Remote sensor for KNX room temperature control unit, UP/PI art. no. MTN��0.

■■■■■■

Remote sensor for room temperature control unit UP/PI

Version Art. no.

black MTN616790

Temperature sensor the floor/room temperature measurementCable length: � m (� x 0.�� mm�)

ISC0��_V�.0_0�_�00�_EN��


Room temperature control unit AltiraKNX Room temperature control unit with display

Version Art. no.

n white ALB45154


� modulesIn Altira design.KNX Room temperature control unit with display and � buttons. � buttons allow to shift set values and change operation modes, the other � buttons are used for navigation in the menu.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:


Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons:Selection of �- � operating modes each push-button. Move setpoint.Contents: With bus connecting terminal.

■■■■■■■

��ISC0��_V�.0_0�_�00�_EN


Room temperature control unit UnicaKNX Room temperature control unit with display

Version Art. no.

n white MGU3.534.18

n ivory MGU3.534.25

� modulesIn Unica design.KNX Room temperature control unit with display and � buttons. � buttons allow to shift set values and change operation modes, the other � buttons are used for navigation in the menu.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:



■■■■■■■

ISC0��_V�.0_0�_�00�_EN��



Version Art. no.

n white MGU5.534.18

n ivory MGU5.534.25



Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons:Selection of �- � operating modes each push-button. Move setpoint.Contents: With fixing frame. With bus connecting terminal.

■■■■■■■

��ISC0��_V�.0_0�_�00�_EN



Version Art. no.





Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons:Selection of �- � operating modes each push-button. Move setpoint.Contents: With fixing frame and claws. With bus connecting terminal.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN��


Room temperature control unit Unica TopKNX Room temperature control unit with display

Version Art. no.



� modulesIn Unica Top design.KNX Room temperature control unit with display and � buttons. � buttons allow to shift set values and change operation modes, the other � buttons are used for navigation in the menu.The room temperature control unit can be used for heating and cooling with infinitely adjust-able KNX valve drives or to trigger switch actuators and heating actuators. With the white backlit display for showing e.g. the time, date, temperature and operating mode. Menu for setting default operating modes, setpoint value, working/non-working day (external trigger), display mode, time, switching times and brightness of the display.With integrated bus coupler. The bus is connected using a bus connecting terminal.KNX software functions: Functions of the room temperature control unit:Controller type: �-step control, continuous PI controller, switching PI controller (PWM)Output: continuous in the range 0 to �00% or switching ON/OFFController mode:



■■■■■■■

��ISC0��_V�.0_0�_�00�_EN



Version Art. no.





Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons:Selection of �- � operating modes each push-button. Move setpoint.Contents: With fixing frame. With bus connecting terminal.

■■■■■■■

ISC0��_V�.0_0�_�00�_EN��



Version Art. no.





Operating modes: Comfort, comfort extension, standby, night reduction, frost/heat protectionMove all setpoints, save all setpoint temperatures and operating modes when reset, external temperature monitoring, additional output of the control value as � byte value on the PWM.Monitoring function for the actual temperature, valve protection function. Functions of the push-buttons:Selection of �- � operating modes each push-button. Move setpoint.Contents: With fixing frame and claws. With bus connecting terminal.

■■■■■■■

��ISC0��_V�.0_0�_�00�_EN


Room temperature control actuatorEMO valve drive with 2 binary inputs EMO valve drive


polar white MTN639118 polar white MTN639119

Electromotive proportional valve drive with integrated bus coupler and microprocessor control with automatic valve lift detection. With two integrated binary inputs.The valve drive can be connected directly to the KNX. A separate power supply is not required.KNX software functions: Control value. Ac-tual position. Status. Forced position (window “Open” detection, lower and upper limit for basic temperature control of underfloor heat-ing for example). Binary inputs. Limit value.Power consumption: typ. �0 mA (= ��0 mW; approx. � BCU modules) Lift: min. �.0 mm; max. �.� mm Running time: �� s/mm Type of protection: IP �� in line with EN �0�� (for vertical installation) Protection class: III in line with EN �0��0 Connecting cable: 1 m fixed; J(E)YY �x�x0.� Connection to bus line: via bus connecting terminal Installation: suitable for all Heimeier thermo-static valve bodies and three-way changeover valvesAccessories: Programming magnet, art. no. MTN��0.

Electromotive proportional valve drive with integrated bus coupler and microprocessor control with automatic valve lift detection.The valve drive can be connected directly to the KNX. A separate power supply is not required.KNX software functions: Setpoint position (control value). Actual position. Status signal. Forced position. Cyclical monitoring.Power consumption: max. �� mA at �0 V (= ��0 mW) Lift: max. �.� mm Running time: �� s/mm Type of protection: IP �� in line with EN �0�� (for vertical installation) Protection class: III in line with EN �0��0 Connection cable: 1 m fixed; J-Y (St) Y 1 x � x 0.� Connection to bus line: via bus connecting terminal Installation: Fits all Heimeier thermostat valve basesAccessories: Programming magnet, art. no. MTN��0.

Programming magnet

Version Art. no.

MTN639190

Non-contact programming of the physical address of the EMO valve drive or KNX ARGUS ��0.

ISC0��_V�.0_0�_�00�_EN��0


KNX fan coil actuator REG-K

Version Art. no.


For heating, ventilation and air conditioning control. For controlling fan convectors with up to three speeds, as well as for controlling three-step motor drives (continuous/pulse-width-modu-lated) or two-step thermal drives. The actuator supports �-pipe and �-pipe systems.Two floating binary inputs for window contact and level contact for condensed water container, for example. Connection of �-speed to �-speed fans. The multi-function push-button with room temperature control can be used to activate the fan coil actuator.With integrated bus coupler. For installation on DIN rails EN �0��. The bus is connected us-ing a bus connecting terminal; a data rail is not necessary.KNX software functions: Fan control: In automatic mode, the fan speeds are controlled dependently by the control value of the multi-function push-button. The three fan speeds and automatic mode can be switched via EIB telegram. The fan can be controlled either directly or via actuators / suitable dimming actuators. Fan speed feedback is possible via corresponding status feedback objects e.g. status LED of the push-button. The fan speed as well as the automatic status “(Auto)” can be displayed on the display of the multi-function push-button with TCU. Valve control: Type of controller: PI controller (PWM and continuous). Controller mode: Heating and/or cooling with common or separate valve outputs. Operating modes: The operating mode is selected in the multi-function push-button with TCUPower supply: AC ��0 V ±�0 %, �0/�0 Hz Power consumption: max. � VA Outputs: 3 floating contacts (fan coil), 2 semi-conductor switches (valve connections) Switching capacity for valves: 0.� A, AC ��V - ��0 V Additional relay switching capacity: �� A Fan relay switching capacity: � A Inputs: �, max. cable length � m Operation: Key for fan levels and heating/cooling mode Displays: � status LEDs Device width: � modules = approx. �� mmAccessories: Multi-function push-button with room temperature control unit, art. no. MTN��.., MTN��.. , MTN��.., MTN��.., MTN��.., MTN��... Themoelectric valve drive �� V art. no. MTN��.

Heating actuator REG-K/6x230/0.05 A

Version Art. no.


For actuation of thermoelectric valve drives for heating or cooling ceilings. The heating actuator has � electronic outputs. Up to � valve drives can be connected to each output. The outputs are either switch activated (� bit) or PWM signal (� byte) activated. Each output is overload-protected and short-circuit-protected. For installation on DIN rails EN �00��.The bus is connected using a bus connecting terminal; a data rail is not necessary.KNX software functions: Cycle time, status feedback, summer and winter operation, cyclical monitoring of variables, locking each output in a forced position, behaviour on bus power fail-ure and recovery, overload and short circuit status, mains power loss reporting, collective fault reporting connected to all valves, transmission of the largest � byte variable value.Nominal voltage: AC ��0 V, �0-�0 Hz Outputs: �, electronic Nominal current: 0.0� A, ohmic Starting current: max. �.� A Minimum load per used output: � valve drive Number of valve drives max. � per output Device width: � modules = approx. �� mmContents: With bus connecting terminal and cable cover.

��ISC0��_V�.0_0�_�00�_EN


Thermoelectric valve drive 230 V

Version Art. no.


Thermoelectric valve drive for opening and closing valves. For �-step or PWM control of heating, air conditioning and ventilation systems, individual room control of surface heaters, control of heating circuit distributors, radiators, convector heaters, cooling ceilings. Operation is carried out by the heating actuator REG-K/ �x��0/0.0� A or a room temperature control unit (��0 V) with �-step or PWM output.Valve adapters permit compatibility with a variety of valve bodies and heating circuit distribu-tors.

First-open function: The drive is factory-set to de-energised open. This allows the heating to be operated during the building shell phase. De-energised closed Functional display (open, closed, intermediate settings) Adjustment control Protection against dismantling Plug-in connecting cable Plug-in assembly

Supply voltage: AC ��0 V, �0/�0 Hz Starting current: max. �00 mA for max. �00 ms Operating current: � mA Power consumption: �.� W Lift: approx. � mm Running time: �� s/mm Positioning force: �00 N Circulating medium temperature: 0-�00°C Type of protection: IP �� / II, in all installation positions Connecting cable: � m, �x0.�� mm² PVC Dimensions: �0x��x�� mm (HxWxD)

■

■■■■■■

Thermoelectric valve drive 24 V

Version Art. no.


Thermoelectric valve drive for opening and closing valves. For �-step or PWM control of heat-ing, air conditioning and ventilation systems, individual room control of surface heaters, control of heating circuit distributors, radiators, convector heaters, cooling ceilings. Fan coil actuator REG-K or a room temperature control unit (�� V) with �-step or PWM output activates.Valve adapters permit compatibility with a variety of valve bodies and heating circuit distribu-tors.

First-open function: The drive is factory-set to de-energised open. This allows the heating to be operated during the building shell phase. De-energised closed Functional display (open, closed, intermediate settings) Adjustment control Protection against dismantling Plug-in connecting cable Plug-in assembly

Supply voltage: AC/DC �� V +�0%/-�0%, 0-�0 Hz Starting current: max. ��0 mA for max. � min Operating current: �� mA Power consumption: �.� W Lift: approx. � mm Running time: �� s/mm Positioning force: �00 N Medium temperature: 0-�00°C Type of protection/protection class: IP �� / II, in all installation positions Connecting cable: � m, �x0.�� mm² PVC Dimensions: �0 x �� x �� mm (HxWxD)

■

■■■■■■

ISC0��_V�.0_0�_�00�_EN��


Valve adapter VA50 for thermoelectric valve drive



MTN639150 MTN639178

For Honeywell+Braukmann, Reich, Landis+Gyr, MNG, Cazzagniga.Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors

For Danfoss RA.Valve adapters permit compatibility with a variety of valve bodies and heating circuit distributors


Version Art. no.

MTN639180

For Heimeier, Herb, Onda, Schlösser (from ��), Oventrop M�0x�.�, TeSa.Valve adapters permit compatibility with a variety of valve bodies and heating circuit distribu-tors

��ISC0��_V�.0_0�_�00�_EN

KNXAccessories

Power suppliesPower supply REG, 24 V DC / 0.4 A

Version Art. no.


Power supply for �� V binary inputs. For installation onto DIN rails EN �00��. With integrated overload and short-circuit protection.Primary supply: AC ��0 V, ��-�� Hz Output voltage: DC �� V +/- � % Output current: max. 0.� A Output power: max. �0 W Device width: � module = approx. �� mmFor supplying power to: Binary input REG-K/�x�� art. no. MTN��. Binary input REG-K/�x�� art. no. MTN��. KNX/IP router REG-K art. no. MTN��0��.

Power supply REG, 24 V DC / 1.25 A

Version Art. no.


Power supply for �� V binary inputs, IC � KNX Internet Controller REG-K, REG-K panel con-trol, KNX/IP router REG-K, �0” IP touch panel. For installation onto DIN rails EN �00��. With integrated overload and short-circuit protection.Primary supply: AC �00-��0 V, �0-�0 Hz Output voltage: DC �� V +/- � % Output current: max. �.�� A Output power: max. �0 W Device width: � modules = approx. �� mmFor supplying power to: Binary input REG-K/�x�� art. no. MTN��. Binary input REG-K/�x�� art. no. MTN��. KNX/IP router REG-K art. no. MTN��0��. IP touch panel �0” art. no. MTN��0�0.

Power supply REG, AC 24 V/1 A

Version Art. no.


Power supply for �� V binary inputs, weather station REG-K/�-gang, analogue input module REG-K/�-gang, rain sensor, wind sensor with 0 - �0 V interface and heating, KNX/IP router REG-K. For installation onto DIN rails EN �00��. With fuse.Primary supply: AC ��0 V, +/- �0 %, �0-�0 Hz Output voltage: AC �� V Output current: max. � A Fuse: �x�0 mm, ��0 V, T ��0 mA Device width: � modules = approx. �0 mmFor supplying power to: Binary input REG-K/�x�� art. no. MTN��. Binary input REG-K/�x�� art. no. MTN��. Weather station REG-K/�-gang, art. no. MTN��. Analogue input REG/�-gang art. no. MTN��. Analogue input module REG/�-gang art. no. MTN��. Thermoelectric valve drive �� V art. no. MTN��.Contents: With spare fuse.

ISC0��_V�.0_0�_�00�_EN��

Taha Mallat

Highlight

Taha Mallat

Highlight

Index

ALB��0 ��ALB�� ALB�� ALB�� ALB�� ALB��0 ��ALB�� ALB�� ALB�� ALB�� MGU�.��0.�� MGU�.��0.�� MGU�.��0.�� MGU�.��0.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��0.�� MGU�.��0.�� MGU�.��0.�� MGU�.��0.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�.��.�� MGU�.��.�� MGU�.��.�� MGU�.��.�0 ��MGU�0.��0.�� MGU�0.��0.�� MGU�0.��0.�� MGU�0.��0.�0 ��MGU�0.��.�� MGU�0.��.�� MGU�0.��.��

MGU�0.��.�0 ��MGU�0.��.�� MGU�0.��.�� MGU�0.��.�� MGU�0.��.�0 ��MGU�0.��.�� MGU�0.��.�� MGU�0.��.�� MGU�0.��.�0 ��MGU�0.��.�� MGU�0.��.�� MGU�0.��.�� MGU�0.��.�0 ��MTN��0�� MTN��0�� MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN��0 ��MTN��0 ��MTN��0 ��MTN��0 ��MTN��0 ��MTN��0�� MTN��00 �0MTN��0� �0MTN��0 ��MTN��00 �0MTN��0� �0MTN��0 ��MTN��00 �0MTN��0� �0MTN��0 ��MTN��0�� MTN��0�� MTN�� 0�MTN�� 0�MTN��0

�0�, ��MTN�� 0�MTN��0 �0�MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN��

MTN��0 ��MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN��-0�� ,

�00MTN��-0�� ,

�00MTN��-0�� ,

�00MTN��-0�� ,

�00MTN��-0�� ,

�00MTN��-0�� ,

�00MTN��-0��0 ��,

�00MTN��-�0�� ,

�0�MTN��-�0�� ,

�0�MTN��-�0�0 ��,

�0�MTN��-�� ,

�0�MTN��-0�� ,

�0�MTN��-0�� ,

�0�MTN��-0�� ,

�0�MTN��-0�� ,

�0�MTN��-0�� ,

�0�MTN��-0�� ,

�0�MTN��-0��0 ��,

�0�MTN��-�0�� ,

�0�MTN��-�0�� ,

�0�

MTN��-�0�0 ��, �0�

MTN��-�� , �0�

MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0��0 �0�MTN��0 ��MTN�� ,

�0�MTN��0 ��,

�0�MTN�� ,

��, ��, ��, �0�, �0�, �0�, ��0

MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0�� 0�MTN��-0��0 �0�MTN��-�0�� MTN��-�0�� MTN��-�0�0 ��MTN��-�� MTN�� MTN��0 ��MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN��0 ��MTN�� MTN��0 ��MTN�� MTN��0 ��MTN�� MTN��0 ��MTN�� MTN��0 ��MTN��0-000� ��MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN�� MTN��0 ��

MTN�� MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN��0 ��MTN��0-000� ��MTN��0-000� ��MTN��0-00�� MTN��0-00�� MTN��0-0�� MTN��0-0�� MTN��0-0�� MTN��0-0�� MTN��0-�� MTN��0-�� MTN��0-�� MTN��0-�� MTN��0-�� MTN��0-��0 ��MTN�� ,

�0�MTN�� ,

�0�MTN�� MTN��0 ��MTN�� MTN�� MTN��0 ��MTN�� MTN��0 ��MTN�� MTN��0 ��MTN��0�� 0MTN��0�� 0MTN��0�� 0MTN��0�0 �0MTN��0�� MTN�� 0MTN�� 0MTN�� 0MTN��0 �0

��ISC0��_V�.0_0�_�00�_EN

MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN��0 ��MTN�� ,

�0�MTN�� ,

�0�MTN�� ,

�0�MTN��0 ��,

�0�MTN�� ,

��0MTN�� ,

��0MTN�� ,

��0MTN��0 ��,

��0MTN�� 0MTN��0�� MTN��0�� MTN��0�� MTN��0��0 ��MTN��0�� MTN��0��0 ��MTN��0�� 0MTN��0��0 �0MTN��0�� MTN��0��0 ��MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN��0 ��MTN�� ,

�0�MTN��0 ��,

�0�MTN�� ,

�0�MTN�� ,

�0�MTN�� 0MTN�� 0MTN�� MTN�� MTN��0 ��MTN�� MTN��0 ��MTN��0 ��0MTN�� 0MTN�� 0MTN�� MTN�� MTN�� MTN�� MTN��0�� MTN�� MTN��0 �0MTN��0� ��MTN��0� ��MTN�� MTN��0�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN��0� ��MTN��0� �0MTN��0� ��MTN��0� ��MTN�� MTN��0 �0MTN�� MTN�� MTN��0 ��MTN��0 ��MTN��0� ��MTN��0� ��MTN��0� ��MTN��0� ��MTN��0� ��MTN�� MTN��0��0 �0MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN��

MTN��0 ��MTN�� MTN�� MTN�� MTN�� MTN��0 ��MTN�� MTN�� MTN��0�� MTN��0�� MTN��0 ��MTN�� MTN��0�0� ��MTN��0�0� ��MTN��0�0 ��MTN��0�� MTN�� MTN��0 ��MTN��0�� MTN��0�0� ��MTN��0�� MTN��0��0 �0MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN�� MTN��0�0 ��MTN��0�� MTN��0�� MTN��0�� MTN�� MTN�� MTN��0 ��MTN��0� ��MTN��0�� MTN��0�� MTN��0�� MTN��0� ��MTN��0� ��MTN��0�� MTN��00� ��MTN��00� ��

Index

ISC0��_V�.0_0�_�00�_EN��

Knx Pushbuttons

Documents

Transcript of Knx Pushbuttons