Klaxon Motor Driven Horn - stevenengineering.com · Klaxon® Motor Driven Horn The A1 series is a...
Transcript of Klaxon Motor Driven Horn - stevenengineering.com · Klaxon® Motor Driven Horn The A1 series is a...
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
6-31
FEATURES
> Completely assembled
> Rugged, heavy-duty design
> Complete with mounting bracket
> Automatic resettable overloadprotection
SPECIFICATIONS
> 110dB at 10 ft (3.05m)
> Frequency - 470 Hz
> Rated for intermittent use -2 minutes on, 5 minutes off
HORNS & SIRENSD
-04
Klaxon®
Motor Driven Horn
The A1 series is a signal that sounds the easily recognized and
unique Klaxon audible tone. The sound is produced by the revolu-
tion of a serrated rotor against a hardened steel stud riveted to the
center of a diaphragm.
The A1 is designed for bracket mounting using the supplied
bracket. The signal is supplied with wire leads for connection in an
appropriate electrical box.
Designed for use in industrial areas or high noise, severe weather
environments such as marinas or shipyards.
A1 Series
Weatherproof
5 43/64(144)
3 35/64(135)
2 Holes9/32 (7)
25/32 (20)
3 35/64(90)
1/2" - 14NPT
3 13/16(97)
5 19/64(135) 4 45/64
(119)
Cat. No. Volts Current
A1-G1 24V DC 2.3A
A1-G5 24V AC 50/60 Hz 4.0A
A1-N5 120V AC 50/60 Hz 0.84A
A1-S1 250V DC 0.35AKLAXON is a registered trademarkof Klaxon Signals Ltd.
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-36ELECTRONIC SIGNALS
5542RPU Remote Paging Unit
Sends audio page to, and is powered by the 5540MP-24Y6. UL and
cUL Listed. Input is received from a microphone input or audio pair
signal source such as phone PBX. Indoor, Type 2 enclosure when
flush wall mounted. Indoor, Type 12 or 2 when mounted to outdoor
listed 4" square utility box. Outdoor, Type 3R and Indoor Type 12 or
2 when mounted with 5542WPK to outdoor listed 4" square utility
box.
5542RPU-M Remote Paging Unit
Same as 5542RPU but includes 5542MIC-H Hand Held Microphone.
5542MIC-H Hand Held Microphone
Optional. May be plugged into 5542 RPU either permanently or as
needed.
5542MIC-D Desktop Microphone
Optional. May be plugged into 5542RPU either permanently or as
needed.
5542WPK Weatherproof Mounting Kit
Optional. Intended for use with 5542RPU or 5542RPU-M to provide
Type 3R outdoor protection for the 5542RPU series.
Weatherproof mounting kit for use with the 5542 Series Remote
Paging Unit. The mounting kit is UL Listed, CSA Certified and has a
Type 3R rating when mounted to the weatherproof box (included).
MR-201/C Relay
Optional. Used to enable the audio output from the 5540MP-24Y6 to
override output from other sources to the same 5532B or 5532BHV
series, 5532M or 5532MHV series, 5536M or 5536MHV series, and
5545B series products in the system.
5542RPU
Adaptatone® MillenniumRemote Paging Unit
FEATURES
> Weatherproof when mounted with5542WPK
> Optional Desk Microphone
> Removable Microphones
AGENCY APPROVALS
> UL 464 Listed
> cUL C22.2 No. 205
> Indoor Type 2 enclosure whenflush wall mounted
> Indoor Type 12 or 2 whenmounted to outdoor listed 4"(102mm) square utility box
> Outdoor Type 3R and indoor Type12 or 2 when mounted with5542WPK to outdoor listed 4"(102mm) square utility box
System Wide Paging
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-37
Cat. No. 5542RPU with 5542WPK weatherproof mounting kit
HazardousLocationSpeaker/AmplifierCat. Nos. 5545B
Speaker/AmplifierCat. No. 5532MHV
Speaker/AmplifierCat. No. 5532M
Local/System SignalCat. No. 5536M
3 Local Tones
Central ToneGenerator with pagingCat. No. 5540MP
ReentrantSpeakerCat. No. 5547
Cone SpeakerCat. No. 5551B
Remote AmplifierCat. No. 5535
Remote Signal ActuatorCat. No. 5538-4
for local inputs 2, 3, 4
4 wires
5 wires
Cat. No. 5542RPU-M1V peak to peak audiosource or telephone systemaudio converted usingBogen Telephone AccessModule or equivalent
*Local Power 3 wires
Typical Adaptatone Paging System Configuration
D-04
Cover Assembly
5542RPU RemotePage Unit Four (4) #6-32 x 3/8"
mounting screws(supplied with 5542WPK)
Cover Gasket
WeatherproofBack Box
Four (4) #6-32 x 5/8"mounting screws(supplied with 5542RPU Series)
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com12-6
0FIRE ALARM EQUIPMENT
© Copyright 2004 Edwards
Vibrating FireAlarm Bells
FEATURES
> 6" (152mm), 8" (203mm) and 10"(254mm) gong sizes
> Heavy duty die cast housing
> Rugged, compact mechanism
> Rated for outdoor use withoptional back box
> Under dome mechanism
AGENCY APPROVALS
> UL Listed
> CSFM Listed
> FM Approved
438D & 439D Series
Diode PolarizedAC & DC Models
The Edwards Fire Alarm Bells are diode polarized, vibrating bells de-
signed for use with fire alarm control equipment. The gongs are made of
select, alloy steel to sound the loud, resonant tone required in fire alarm
systems. They are epoxy powder coated red.
Supplied mounting plate installs directly on surface or on any single
gang box, or on any 3 1/2" (89mm) or 4" (102mm) octagon, or 4"
(102mm) square electrical box.
For outdoor installation, use Edwards Cat No. 449 weatherproof back
box.
The 438D and 439D fire alarm bells are audible signaling appliances for
installations that operate in conjunction with an installed fire alarm panel
and detection devices.
ACCESSORIESCat. No. Description
449 Weatherproof back box
D-0
4
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
12-61FIRE ALARM EQUIPMENT
© Copyright 2004 Edwards
10" (254mm)
8" (203mm)
6" (152mm)
Mounting plate (furnished)mounts directly on surface
or any single gang open
7"(178mm)
5"(127mm)3"
(76mm)
2 29/32"(74mm)
3 11/32"(85mm)
3 15/32"(88mm)
5 1/16"(129mm)
5 1/2"(140mm)
5 5/8"(143mm)
Cat. No. 449Weatherproof
Back Box(optional)
Gong Size
Gong Lead dB atCat. No. Volts Amps Size Length 10 Ft. (3.05m)
438D-6N5-R 120V AC .034 6" (152mm) 10" (25mm) 76* / 66**
438D-8N5-R 120V AC .034 8" (203mm) 10" (25mm) 86* / 75**
438D-10N5-R 120V AC .034 10" (254mm) 10" (25mm) 88* / 79**
439D-6AW-R 24V DC .085 6" (152mm) 10" (25mm) 92* / 82**
439D-8AW-R 24V DC .085 8" (203mm) 10" (25mm) 93* / 82**
439D-10AW-R 24V DC .085 10" (254mm) 10" (25mm) 94* / 85**
439D-6AW-RAU 12V DC .150 6" (152mm) 10" (25mm)
439D-8AW-RAU 12V DC .150 8" (203mm) 10" (25mm)
439D-10AW-RAU 12V DC .150 10" (254mm) 10" (25mm)
*Anechoic Chamber **Reverberant Room measured on the A scale
D-04
ELECTRONIC SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
4-51
Multi-power Taps2.5W, .5W, 1W & 2W
Cone Speaker
The Edwards 5551B-2W speakers are voice/tone notification appli-
ances designed for indoor ceiling or wall mounting and offer low
power consumption, multi-watt power selection, and high sound
level output.
Mounts on four inch square backbox with extension ring
They are primarily intended for use with the 5535 Remote Amplifier.
See 5535 Remote Amplifier, page 4-48. May be used for fire alarm
applications with compatible fire alarm control panels. Consult the
installation instructions supplied with the control panel.
8"(203mm)
One of two#8-32 x 1 1/2"(38mm) screws
2 1/2"(64mm)
5551B-2W
Multi-watt power selection
Wall or ceiling mount
Fire retardant and moisture proof
UL 1480 Listed for use in firealarm or emergencycommunication systems installedin accordance with NFPA 72National Fire Alarm Code
Four power taps - .25W, .5W,1.0W and 2.0W
70V RMS
Color - White
Sound Pressure Level*Cat. No. Input Voltage .25W .50W 1.0W 2.0W
5551B-2W 70V RMS 75 dBA 81 dBA 84 dBA 87 dBA
*At 10 feet (3.05m) in a reverberant room using 400-4000 Hz band limited pink noise perUL 1480
© Copyright 2004 Edwards
D-04
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Edwards vibrating AdaptaBuzzers are the finest, heavy duty buzzers
available. The AC models are volume adjustable.
Universal Adaptaplate® mounts directly on any single-gang box, 3
1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm) octagon box. Buzzer
plugs into receptacle on mounting plate. For flush mounting acces-
sories see page 5-10.
Used for timing, scheduling, and paging applications. Use wherever
a relatively low decibel signal of a different tone is required.
AdaptaBuzzerTM
AC and DC Models
5 1/16"(128mm)
2 1/4"(57mm)
FEATURES
> Vibrating Armature
> Universal Adaptaplate® mountsdirectly on surface or electricalbox
> Plug-in convenience
> Corrosion resistant heat flowedepoxy finish
AGENCY APPROVALS
> 340A Series UL 464 Listed
> 340A Series FM Approved
340A & 343A Series
DC Coil dB atCat No. Volts Amps VA Res (ohms) 1m / 10 ft.
340A-G5 24V 50/60 Hz 0.250A 6.0 28 76 / 70340A-N5 120V 50/60 Hz 0.050A 6.0 725340A-R5 240V 50/60 Hz 0.025A 6.0 2900
343A-E1 12V DC 0.330 4.0 9.4 68 / 62343A-G1 24V DC 0.150 3.6 28343A-M1 75V DC 0.065 4.9 360343A-P1 125V DC 0.070 8.8 1000
5-28
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Flush mounted, heavy duty buzzer designed for standard outlet box
installation. The 1064 Series are provided with terminals for wiring
connections. The 1065 Series are provided with flying leads for wir-
ing connections
Installs in standard outlet boxes using any standard wall plate.
Low cost, quality buzzer widely used in homes, apartment houses,
plants, and OEMs.
Strap Mounted Buzzer
1064 & 1065 Series
Low power drain
FEATURES
> High voltage
> Adjustable volume
> Zinc-plated finish
> Low power drain permits longwire runs
> 1064 has terminal connectors
> 1065 has flying leads
AGENCY APPROVALS
> UL 464 Listed
1"(25mm)
3 3/4"(95mm)
3 3/16"(81mm)
2 3/8"(60mm)
1 3/8"(35mm)
DC Coil dB atCat No. Volts Amps VA Res (ohms) 1m / 10 ft.
1064-G5 24V AC 50/60 Hz 0.25A 6 36 82 / 761064-N5 120V AC 50/60 Hz 0.05A 6 9251064-R5 240V AC 50/60 Hz 0.025A 6 3600
1065-G5 24V AC 50/60 Hz 0.25A 6 36 82 / 761065-N5 120V AC 50/60 Hz 0.05A 6 9251065-R5 240V AC 50/60 Hz 0.025A 6 3600
Cat. No. 1064
Cat. No. 1064 Shown
5-32
D-0
4
ELECTRIC CHIMES
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com9-6
© Copyright 2004 Edwards
Surface MountSingle-Stroke Chimes
338 & 339 Series
The Edwards 338 & 339 are surface mount AC or DC single stroke
chimes which can be pulsed up to 10 pulses/second. The chimes
are high quality units with underdome construction intended for
heavy-duty commercial and industrial use. The chimes require no
lubrication.
The chimes come complete with an Adaptaplate® mounting plate.
The Adaptaplate mounts on any plaster cover with mounting holes
on 2 3/4" (70mm) centers, on any single gang opening, on any
3 1/4" (83mm), 3 1/2" (89mm), or 4" (102mm) octagon or square
box. Also mounts directly on any wall surface. For flush mounting
use Cat. No. 512-A grille (page 5-10) and P-029522 back box.
For paging and scheduling applications requiring a pleasant note
with middle range decibel rating. Ideal for offices and stores.
Low Current Drain
FEATURES
> AC or DC models
> No exposed terminals
> Tamper-proof cover screw
> Plastic tipped stainless steelstriker
> Satin aluminum finish
AGENCY APPROVALS
> UL Listed
D-0
4
ELECTRIC CHIMES
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
9-7© Copyright 2004 Edwards
3 5/32"(80mm)
6 1/2"(165mm)
Cat. No. Volts Amps V A dB at 10 ft
338-G5 24V AC 50/60 Hz .5 12 81
338-N5 120V AC 50/60 Hz .1 12 81
339-E1 12V DC 0.6 7.2 81
339-G1 24V DC .3 7.2 81
D-04
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Edwards 118 Series DC and 123A Series AC Midi Vibrating Horns
are designed primarily for security systems and for signaling de-
vices on an OEM basis.
Supplied with mounting bracket and simply attaches to mounting
surface using #8-32 screw.
Used for security systems, office machines, low-voltage trouble
alarms, home appliances, data monitoring systems, computers,
and timing devices.
Midi Vibrating Horns
118 & 123A Series
Compact size
FEATURES
> Low power drain
> Compact size
> Shock resistant
> Easy surface mount installation
SPECIFICATIONS
> Temperature range: -40° to 180°F(-40 to 82°C)
> Weight: 3 oz (85g)
3/16"(5mm)
2 1/32"(51mm)
1 3/4"(45mm)
6" (152mm)2 wires on AC
A
DC Coil dB at WidthCat No. Volts Amps VA Res (ohms) 1m / 10 ft. (A dimension)
118-E1 12V DC 0.07A 0.84 25.5 92 / 86 1 11/64"118-G1 24V DC 0.03A 0.72 102.0 (30mm)
123A-E5 12V AC 60 Hz 0.4A 4.8 10.0 92 / 86 1 3/16"123A-G5 24V AC 60 Hz 0.2A 4.8 40.0 (30mm)123A-N5 120V AC 60 Hz 0.04A 4.8 1200.0
5-37D
-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-2
Adaptabel single stroke bells produce an individual, clearly defined
note. When current is applied, the striker hits the gong once and
stops. Coded, intermittent current may be used to cause the striker to
hit the gong, pause and hit again for any given period. Ideal for use
with momentary initiating contacts.
Universal Adaptaplate® mounts directly on surface or fits any
single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm)
octagon box, or any plaster cover with mounting holes on 2 3/4" (70
mm) centers. 6" and 10" bells also mount on 4" (102 mm) square
boxes. See accessories on page 5-10.
Specified for timing, scheduling, paging and general alarm applica-
tions. 4" (102 mm) sizes recommended for quiet office areas. 6" (152
mm) sizes for moderate noise level areas such as general factory ar-
eas. 10" (254 mm) sizes for loud areas such as heavy machine shops.
Available with full cast grids and protective grilles. See Accessories
on page 5-10 for available options.
Adaptabel® AC SingleStroke Bells
332 Series
PLC Compatible
FEATURES
> Completely assembled, allhardware supplied
> Universal Adaptaplate mountsdirectly on surface or electricalbox
> Shockproof die cast housing
> Dustproof
AGENCY APPROVALS
> UL 464 Listed
> FM Listed
SPECIFICATIONS
> Rated 400 hours at 50% dutycycle
> Self-compensating solenoidplunger
> Corrosion resistant heat flowedepoxy finish
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-3
dB at DC CoilCat No.* Volts Amps VA 1m / 10 ft. Res (Ohms)
332-4G5 24V AC 50/60 Hz 0.50 12 90 / 84 10332-4N5 120V AC 50/60 Hz 0.10 12 250
332-6G5 24V AC 50/60 Hz 0.50 12 92 / 86 10332-6N5** 120V AC 50/60 Hz 0.10 12 250332-6R5 240V AC 50/60 Hz 0.05 12 1000
332-10G5 24V AC 50/60 Hz 0.70 16.8 98 / 92 5332-10N5** 120V AC 50/60 Hz 0.14 16.8 130*Gong Size in inches denoted by suffix in catalog number.** Diode Polarized models avaiable. Order 332D-6N5 or 332D-10N5. Add "-R" for red.
SIGNAL INPUT LOAD CHARACTERISTICS†
Light Source Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. Voltage leakage current (mA) Current (mA) Amps/milliseconds
332-4N5 120V AC 60 Hz 25 100 0.41/4.5332-6N5 120V AC 60 Hz 25 100 0.40/4.6332-10N5 120V AC 60 Hz 25 140 0.53/4.5† This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
2 13/32"(61 mm)
4 1/2"(114 mm)
3 11/16"(94 mm)
7 1/8"(181 mm)
4 13/16"(122 mm)
10 1/2"(267 mm)
4" Bell
6" Bell
10" Bell
EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE
1. Pull wires throughcenter hole and connect tobinding post.
3. Tighten front screw to completeinstallation. (Two screws on 4inch bells)
2. Slip Adaptabel onto sturdyhanger and push home. D
-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-12
Hazardous location AC single stroke bells produce a distinctive, loud,
and clear individual note that is free of mechanical clatter. When cur-
rent is applied, the striker hits the gong once and stops. Current may
be coded to cause the striker to hit the gong intermittently. Ideal for
use with momentary initiating contacts.
Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted
with a sealing fitting for 3/4" (19mm) conduit and wire leads for power
connections.
Used for coded signal applications such as paging. Also specified for
timing, scheduling, and general alarm applications in: Refineries,
gasoline storage and dispensing areas, petrochemical manufacturers,
spray paint areas, aircraft hangers, grain dust areas in graineries and
flour mills, and industrial firms using flammable liquids.
Adaptabel® ACSingle Stroke Bells
332EX Series
Explosionproof, NEMA Type 4
FEATURES
> 6" and 10" gong sizes
> Low power drain for efficientoperation over long wire runs
> Completely assembled
> Weatherproof
AGENCY APPROVALS
> UL 1203 Listed
> UL Listed for Class I, Divisions 1and 2, Groups B, C and D; ClassII, Divisions 1 and 2, Groups E, Fand G; and Class III
> NEMA Type 4
SPECIFICATIONS
> Adjustment free self-compensating plunger
> Corrosion resistant finish
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-13
Gong DimensionsSize A B C
6" 4 1/16" 4 13/16" 5/8"(152mm) (103mm) (122mm) (16mm)
10" 6 1/16" 5 3/8" 2 5/8"(245mm) (154mm) (137mm) (67mm)
1 7/16"(37mm)
B
A
Mtg.Bracket3/16"
(5mm)
1 1/4"(32mm)
Mounting hole positions for3/8" (10mm) diameter (max)fasteners with washers
MountingBrackets
6" ± 1/8"(152mm ± 3mm)
C
Peak dB atCat No. Volts Current* 1m / 10 ft. Gong Size
332EX-6G5 24V AC 50/60 Hz 3.40A 92 / 86 6" (152 mm)332EX-6N5 120V AC 50/60 Hz 0.43A332EX-6R5 240V AC 50/60 Hz 0.20A
332EX-10G5 24V AC 50/60 Hz 3.40A 100 / 94 10" (254 mm)332EX-10N5 120V AC 50/60 Hz 0.43A332EX-10R5 240V AC 50/60 Hz 0.20A*Single pulse duration - 8 to 16 milliseconds
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-4
DC single stroke bells produce an individual, clearly defined note.
When current is applied, the striker hits the gong once and stops.
Coded, intermittent current may be used to cause the striker to hit the
gong, pause and hit again for any given period. Ideal for use with mo-
mentary initating contacts.
Universal Adaptaplate® mounts directly on surface or fits any
single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm)
octagon box, or any plaster cover with mounting holes on 2 3/4" (70
mm) centers. 6" and 10" bells also mount on 4" (102 mm) square
boxes.
Specified for timing, scheduling, paging and general alarm applica-
tions. 4" (102 mm) sizes recommended for quiet office areas. 6" (152
mm) sizes for moderate noise level areas such as general factory ar-
eas. 10" (254 mm) sizes for loud areas such as heavy machine shops.
Available with full cast grids and protective grilles. See AdaptaBel Ac-
cessories on page 5-10.
Adaptabel® DCSingle Stroke Bells
333 Series
PLC Compatible
FEATURES
> Universal Adaptaplate mountsdirectly on surface or electricalbox
> Indoor
AGENCY APPROVALS
> UL 464 Listed
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-5
dB at DC CoilCat No.* Volts Amps VA 1m / 10 ft. Res (Ohms)
333-4G1 24 0.30 7.2 90 / 84 73
333-6E1 12 0.60 7.2 18333-6G1 24 0.30 7.2 92 / 86 73333-6P1 125 0.06 7.5 1870
333-10G1 24 0.30 7.2 98 / 92 73333-10P1 125 0.06 7.5 1870*Gong Size in inches denoted by suffix in catalog number.
SIGNAL INPUT LOAD CHARACTERISTICS**Light Source Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. Voltage leakage current (mA) Current (mA) Amps/milliseconds
333-4G1 24V DC 5 300 1.57/0.0001333-6G1 24V DC 5 300 1.72/0.0001333-10G1 24V DC 5 300 1.3/0.000182**This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spikesuppression. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE
1. Pull wires throughcenter hole and connect tobinding post.
3. Tighten front screw to completeinstallation. (Two screws on 4inch bells)
2. Slip Adaptabel onto sturdyhanger and push home.
4 13/16"(122 mm)
10"(254 mm)
10" Bell
2 29/32"(74 mm)
6"(152 mm)
6" Bell
4" Bell2 15/32"(63 mm)
4"(102 mm)
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-14
Hazardous location DC single stroke bells produce a distinctive, loud,
and clear individual note that is free of mechanical clatter. When cur-
rent is applied, the striker hits the gong once and stops. Current may
be coded to cause the striker to hit the gong intermittently. Ideal for
use with momentary initiating contacts.
Mounts to any solid surface using 3/8" (10mm) fasteners. Units fitted
with a sealing fitting for 3/4" (19mm) conduit and wire leads for power
connections.
Used for coded signal applications such as paging. Also specified for
timing, scheduling, and general alarm applications in refineries,
gasoline storage and dispensing areas, petrochemical manufacturers,
spray paint areas, aircraft hangers, grain dust areas in graineries and
flour mills, and industrial firms using flammable liquids.
Adaptabel® DCSingle Stroke Bells
333EX Series
Explosionproof, NEMA Type 4
FEATURES
> 6" and 10" gong sizes
> Low power drain for efficientoperation over long wire runs
> Completely assembled
> Weatherproof
AGENCY APPROVALS
> UL 1203 Listed
> UL Listed for Class I, Divisions 1and 2, Groups B, C and D; ClassII, Divisions 1 and 2, Groups E, Fand G; and Class III
> NEMA Type 4
SPECIFICATIONS
> Adjustment free self-compensating plunger
> Corrosion resistant finish
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-15
Gong DimensionsSize A B C
6" 4 1/16" 4 13/16" 5/8"(152mm) (103mm) (122mm) (16mm)
10" 6 1/16" 5 3/8" 2 5/8"(245mm) (154mm) (137mm) (67mm)
Peak dB atCat No. Volts Current* 1m / 10 ft. Gong Size
333EX-6G1 24V DC 3.50A 92 / 86 6" (152 mm)333EX-6P1 125V DC 0.52A
333EX-10G1 24V DC 3.50A 100 / 94 10" (254 mm)*Single pulse duration - 8 to 16 milliseconds
1 7/16"(37mm)
B
A
Mtg.Bracket3/16"
(5mm)
1 1/4"(32mm)
Mounting hole positions for3/8" (10mm) diameter (max)fasteners with washers
MountingBrackets
6" ± 1/8"(152mm ± 3mm)
C
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-6
AC vibrating bells produce a long continuous ringing sound. The
striker continues to strike the gong in rapid-fire action as long as cur-
rent is applied.
Universal Adaptaplate® mounts directly on surface or fits any
single-gang box, 3 1/4" (83 mm), 3 1/2" (89 mm), or 4 " (102 mm)
octagon box, or any plaster cover with mounting holes on 2 3/4" (70
mm) centers. 6" and 10" bells also mount on 4" (102 mm) square
boxes.
Specified for timing, scheduling, paging and general alarm applica-
tions. 4" (102 mm) sizes recommended for quiet office areas. 6" (152
mm) sizes for moderate noise level areas such as general factory ar-
eas. 10" (254 mm) sizes for loud areas such as heavy machine shops.
Available with full cast grids and protective grilles. May be weather-
proofed with the addition of a weatherproof box. See AdaptaBel Acces-
sories on page 5-10 for available options.
Adaptabel® ACVibrating Bells
340 Series
PLC Compatible
FEATURES
> Universal Adaptaplate mountsdirectly on surface or electricalbox
> Weatherproof by addingappropriate back box
> Completely assembled, allhardware supplied
> Shockproof die cast housing
> Dustproof
AGENCY APPROVALS
> UL 464 Listed
> FM Listed
> CSFM Certified
SPECIFICATIONS
> Self-compensating solenoidplunger
> Rated 400 hours at 50% dutycycle
> Corrosion resistant heat flowedepoxy finish
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-7
4" Bell
6" Bell
EASY INSTALLATION USING THE SUPPLIED ADAPTAPLATE
1. Pull wires throughcenter hole and connect tobinding post.
3. Tighten front screw to completeinstallation. (Two screws on 4inch bells)
2. Slip Adaptabel onto sturdyhanger and push home.
SIGNAL INPUT LOAD CHARACTERISTICS**Light Source Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. Voltage leakage current (mA) Current (mA) Amps/milliseconds
340-4N5 120V AC 60 Hz 25 62 0.095/4340-6N5 120V AC 60 Hz 25 70 0.15/4340-10N5 120V AC 60 Hz 25 70 0.15/4**This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
dB at DC CoilCat No.* Volts Amps VA 1m / 10 ft. Res (Ohms)
340-4E5 12 0.620 7.4 94 / 88 13340-4FM 16 0.460 7.4 22340-4G5 24 0.310 7.4 50340-4N5 120 0.062 7.4 1300340-4R5 240 0.031 7.4 5000
340-6E5 12 0.700 8.4 98 / 92 8340-6FM 16 0.500 8.0 13340-6G5 24 0.350 8.4 30340-6N5 120 0.070 8.4 700340-6R5 240 0.035 8.4 2650
340-10G5 24 0.350 8.4 102 / 96 30340-10N5 120 0.070 8.4 700340-10R5 240 0.350 8.4 2650
*Gong Size in inches denoted by suffix in catalog number.
2 13/32"(61 mm)
4 1/2"(114 mm)
3 11/16"(94 mm)
7 1/8"(181 mm)
4 13/16"(122 mm)
10 1/2"(267 mm)
10" Bell
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-16
Hazardous location AC vibrating bells produce a distinctive, loud,
and clear ringing sound that is free of mechanical clatter. The striker
continues to strike the gong in rapid-fire action as long as current is
applied.
Mounts to any solid surface using 3/8" (10mm) fasteners. Units
fitted with a sealing fitting for 3/4" (19mm) conduit and wire leads
for power connections.
Specified for timing, scheduling, paging, and general alarm applica-
tions in refineries, gasoline storage and dispensing areas, petro-
chemical manufacturers, spray paint areas, aircraft hangers, grain
dust areas in graineries and flour mills, and industrial firms using
flammable liquids.
Adaptabel® ACVibrating Bells
340EX Series
Explosionproof, NEMA Type 4
FEATURES
> 6", 8" and 10" gong sizes
> Low power drain for efficientoperation over long wire runs
> Completely assembled
> Weatherproof
AGENCY APPROVALS
> UL 1203 Listed
> UL Listed for Class I, Divisions 1and 2, Groups B, C and D; ClassII, Divisions 1 and 2, Groups E, Fand G; and Class III
> NEMA Type 4
SPECIFICATIONS
> Adjustment free self-compensating plunger
> Corrosion resistant finish
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-17
Gong DimensionsSize A B C
6" 4 1/16" 4 13/16" 5/8"(152mm) (103mm) (122mm) (16mm)
8" 5 1/16" 5 1/4" 1 5/8"(203mm) (129mm) (133mm) (41mm)
10" 6 1/16" 5 3/8" 2 5/8"(245mm) (154mm) (137mm) (67mm)
RMS dB atCat No. Volts Current 1m / 10 ft. Gong Size340EX-6G5 24V AC 50/60 Hz 0.210A 90/84 6" (152mm)340EX-6N5 120V AC 50/60 Hz 0.041A340EX-6R5 240V AC 50/60 Hz 0.021A340EX-8N5 120V AC 50/60 Hz 0.041A 95/89 8" (203mm)340EX-10G5 24V AC 50/60 Hz 0.210A 94/88 10" (254mm)340EX-10N5 120V AC 50/60 Hz 0.041A340EX-10R5 240V AC 50/60 Hz 0.021A
1 7/16"(37mm)
B
C
Mtg.Bracket3/16"
(5mm)
1 1/4"(32mm)
Mounting hole positions for3/8" (10mm) diameter (max)fasteners with washers
MountingBrackets
6" ± 1/8"(152mm ± 3mm)
C
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-8
DC vibrating bells produce a long continuous ringing sound. The
striker continues to strike the gong in rapid-fire action as long as cur-
rent is applied.
Universal Adaptaplate® mounts directly on surface or fits any single
gang box, 3 1/4" (83mm), 3 1/2" (89mm), or 4" (102mm) octogon box, or
any plaster cover with mounting holes on 2 3/4" (70mm) centers. 6"
and 10" bells also mount on 4" (102mm) square boxes.
The DC vibrating bell can be used in outdoor applications when
mounted on Cat. No. 449 weatherproof back box. See AdaptaBel acces-
sories on page 5-10.
Specified for timing, scheduling, and general alarm applications.
Adaptabel® DCVibrating Bells
435 Series
PLC Compatible
FEATURES
> Universal Adaptaplate mountsdirectly on surface or electricalbox
> Weatherproof by adding 449 backbox
> 4", 6" 8" and 10" gong sizes
AGENCY APPROVALS
> UL 464 Listed
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-9
4" Bell 2 29/32"(74 mm)
6"(152 mm)
6" Bell
4 13/16"(122 mm)
10"(254 mm)
10" Bell
8" Bell
8"(203mm)
3 11/32"(85mm)
2 15/32"(63mm)
4"(102mm)
SIGNAL INPUT LOAD CHARACTERISTICS**Light Source Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. Voltage leakage current (mA) Current (mA) Amps/milliseconds435-4G1 24V DC 5 62 1.06/0.0001435-6G1 24V DC 5 62 1.14/0.000125435-10G1 24V DC 5 62 1.14/0.000125**This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spikesuppression. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
dB at DC CoilCat No.* Volts Amps VA 1m / 10 ft. Res (Ohms)435-4C1 6 0.250 1.5 96 / 90 11435-4E1 12 0.125 1.5 96 / 90 40435-4G1 24 0.062 1.5 96 / 90 155435-4J1 32 0.047 1.5 96 / 90 275435-4P1 125 0.012 1.5 96 / 90 3000435-6C1 6 0.250 1.5 98 / 92 11435-6E1 12 0.125 1.5 98 / 92 40435-6G1 24 0.062 1.5 98 / 92 155435-6J1 32 0.047 1.5 98 / 92 275435-6K1 48 0.031 1.5 98 / 92 620435-6P1 125 0.012 1.5 98 / 92 3000435-6S1 250 0.008 2.0 96 / 90 6100435-8C1 6 0.250 1.5 99 / 93 11435-8E1 12 0.125 1.5 99 / 93 40435-8G1 24 0.062 1.5 99 / 93 155435-8P1 125 0.012 1.5 99 / 93 3000435-10E1 12 0.125 1.5 100 / 94 40435-10G1 24 0.062 1.5 100 / 94 155435-10P1 125 0.012 1.5 100 / 94 3000435-10S1 250 0.008 2.0 96 / 90 6100*Gong Size denoted by suffix in catalog number.*Gong Size in inches denoted by suffix in catalog number.
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-18
Hazardous location DC vibrating bells produce a distinctive, loud,
and clear ringing sound that is free of mechanical clatter. The striker
continues to strike the gong in rapid-fire action as long as current is
applied.
Mounts to any solid surface using 3/8" (10mm) fasteners. Units fit-
ted with a sealing fitting for 3/4" (19mm) conduit and wire leads for
power connections.
Specified for timing, scheduling, paging, and general alarm applica-
tions in: Refineries, gasoline storage and dispensing areas, Petro-
chemical manufacturers, Spray paint areas, Aircraft hangers, Grain
dust areas in granaries and flour mills, and Industrial firms using
flammable liquids.
Adaptabel® DCVibrating BellsExplosionproof, NEMA Type 4
FEATURES
> 6", 8" and 10" gong sizes
> Low power drain for efficientoperation over long wire runs
> Completely assembled
> Weatherproof
> Diode Polarized Models availablefor use in electrically supervisedcircuits
AGENCY APPROVALS
> UL 1203 Listed
> UL Listed for Class I, Divisions 1and 2, Groups B, C and D; ClassII, Divisions 1 and 2, Groups E, Fand G; and Class III
> NEMA Type 4
SPECIFICATIONS
> Adjustment free self-compensating plunger
> Corrosion resistant finish
435EX Series
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-19
Gong DimensionsSize A B C
6" 4 1/16" 4 13/16" 5/8"(152mm) (103mm) (122mm) (16mm)
8" 5 1/16" 5 1/4" 1 5/8"(203mm) (129mm) (133mm) (41mm)
10" 6 1/16" 5 3/8" 2 5/8"(245mm) (154mm) (137mm) (67mm)
1 1/4"(32mm)
Mounting hole positions for3/8" (10mm) diameter (max)fasteners with washers
MountingBrackets
6" ± 1/8"(152mm ± 3mm)
C
RMS dB atCat No. Volts Current 1m / 10 ft. Gong Size435EX-6C1 6 1.520435EX-6E1 12 0.520435EX-6G1 24 0.240 89/83 6" (152mm)435EX-6K1 48 0.110435EX-6P1 125 0.040435EX-6S1 250 0.023435EX-8G1 24 0.290435EX-8K1 48 0.110 92/86 8" (203mm)435EX-8P1 125 0.040435EX-8S1 250 0.023435EX-10E1 12 0.520435EX-10G1 24 0.290 95/89 10" (254mm)435EX-10P1 125 0.040435DEX-6G1+ 24 0.290 89/83 6" (152mm)435DEX-8G1+ 24 0.290 92/86 8" (203mm)435DEX-10G1+ 24 0.290 95/89 10" (254mm)+Diode polarized for use in electrically supervised circuits. CSFM Listed
1 7/16"(37mm)
B
A
Mtg.Bracket3/16"
(5mm)
D-04
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com5-20
The Edwards hazardous location fire alarm bell is the finest heavy
duty, hazardous location bell available today. It delivers a distinc-
tive, clear ring that is free of mechanical clatter. Vibrating bells pro-
duce a long, continuous ringing sound. The striker continues to rap-
idly strike the gong as long as current is applied.
The bell has been designed for indoor applications requiring supervi-
sion of signaling circuit field wiring but may be used for unsuper-
vised applications as well.
Mounts to any solid surface using two 3/8" (10mm) fasteners. Each
unit is supplied with wire leads and a sealing fitting for connection to
3/4" (19mm) conduit.
The 439DEX fire alarm bells are ideally suited for fire alarm applica-
tions in refineries, gasoline storage and dispensing areas, flam-
mable liquid areas, paint spray booths, aircraft refueling areas,
graineries, flour mills, coal mines and other combustible dust areas.
Adaptabel® DCVibrating FireAlarm Bells
439DEX SeriesExplosionproof
FEATURES
> 6". 8" and 10" gong sizes
> Low power drain for efficientoperation over long wire runs
> Completely assembled
> Red epoxy finish
> Diode Polarized Models availablefor use in electrically supervisedcircuits
AGENCY APPROVALS
> UL 1203 Listed
> UL Listed for Class I, Divisions 1and 2, Groups B, C and D; ClassII, Divisions 1 and 2, Groups E, Fand G; and Class III
> CSFM Listed
SPECIFICATIONS
> Adjustment free self-compensating plunger
> Corrosion resistant red finish
D-0
4
BELLS & BUZZERS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
5-21
Gong DimensionsSize A B C
6" 4 1/16" 4 13/16" 5/8"(152mm) (103mm) (122mm) (16mm)
8" 5 1/16" 5 1/4" 1 5/8"(203mm) (129mm) (133mm) (41mm)
10" 6 1/16" 5 3/8" 2 5/8"(245mm) (154mm) (137mm) (67mm)
RMS dB atCat No. Volts Current 1m / 10 ft. Gong Size
439DEX-6AW 20-24V DC 0.240A 89 / 83 6" (152mm)
439DEX-8AW 20-24V DC 0.240A 92 / 86 8" (203mm)
439DEX-10AW 20-24V DC 0.240A 95 / 89 10" (254mm)
1 7/16"(37mm)
B
C
Mtg.Bracket3/16"
(5mm)
1 1/4"(32mm)
Mounting hole positions for3/8" (10mm) diameter (max)fasteners with washers
MountingBrackets
6" ± 1/8"(152mm ± 3mm)
C
D-04
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
The Edwards 660 Series are compact, strap-mounted buzzers and
bells designed for flush mounting in standard electrical boxes.
Designed for installation in standard outlet boxes. Requires a 590
transformer (page 11-2) and push button. Transformer and
pushbutton may be mounted in same 3 gang outlet box with a mini-
mum depth of 1 3/4" (44 mm) using a Cat. No. 593 transformer
mounting plate (page 11-4).
Used for residential and commercial door signals and interoffice
communications and signaling.
Flush-Call StrapMounted Signals
660 Series
Low voltage
FEATURES
> Low voltage
> Easy flush mounting
A
3 5/8"(92mm)
1 3/4"(44mm)
660/661662 Typical Wiring
Diagram
8/10VAC
115VAC
590Transformer
DC Coil dB atCat No. Name Voltage Current* VA Res. (ohms) 1m / 10 ft. Depth (A)
660 RingcallTM Bell 8-10V AC 1.5A 15 4.75 86 / 80 1 3/8" (35 mm)
661 BuzacallTM Buzzer 8-10V AC 1.3A 13 6 86 / 80 7/8" (22 mm)
662 TucallTM Bell/Buzzer 8-10V AC 1.5A 15 4.75 86 / 80 1 3/8" (35 mm)*Current ratings at 10V AC.
5-39D
-04
Low cost, non adjustable bell which may be operated off of a 590
transformer or DC power.
Universal economy bell widely used in homes, apartment houses,
plants, OEMs. Especially suitable for AC powered security sys-
tems with battery standby.
For office installation, see Cat. No. 13 Series Bells on page 5-22 or
Cat. No. 15 and 115 Series Buzzers on pages 5-34 and 5-35. For
combination bell and buzzer see Cat. No. 730 Dixie BuzabelTM on
page 5-38.
General PurposeDixie BellTM
720 Series
Fully Enclosed
1"(25mm)
5 1/4"(133mm)
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS5-
26
DC Coil dB atCat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft
720 6-8V AC 1.20A 7.0 1.5 84 / 783-6V DC
FEATURES
> Low voltage
> AC and DC operation
> Attractive snap-on covers
> Enclosed binding posts
> Corrosion resistant metallic finish
3"(76mm)
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Designed for standard outlet box installation. Provided with leads
for wiring connections.
Low cost, quality buzzer widely used in homes, apartment houses,
plants, and OEMs.
High Voltage Buzzer
1066 Series
Low power drain
DC Coil dB atCat No. Volts Amps VA Res (ohms) 1m / 10 ft.
1066-G5 24V AC 50/60 Hz 0.25A 6 36 80 / 741066-N5 120V AC 50/60 Hz 0.05A 6 9251066-R5 240V AC 50/60 Hz 0.025A 6 3600
13/16"(21mm)
1 1/4"(32mm)
FEATURES
> High voltage
> Adjustable volume
> Zinc-plated finish
> Low power drain permits longwire runs
AGENCY APPROVALS
> UL Recognized
5-33D
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-26HORNS & SIRENS
The Edwards B-KM-8130 Series is a heavy-duty, high decibel, vi-
brating horn signal designed for use in hazardous locations.
Two mounting lugs are provided on either side of the unit for wall
mounting. The housing is tapped on one side for 1/2" (13mm) con-
duit to allow for field wiring installation.
Ideal for use where sound projection in a single direction is required
or specified in hazardous atmospheres where explosion proof and
dust tight features are required.
AdaptaHorn® HazardousLocation SingleProjector Horn
5 3/4"(146mm)
2 holes 3/8" (10mm) Tap 1/2" (13mm) IP
6 1/4"(159mm)
9 3/4"(248mm)7/8" (22mm)
B-KM-8130 SeriesFEATURES
> Corrosion resistant electrostaticheat flowed epoxy finish
AGENCY APPROVALS
> UL Listed for Class I, Division 1and 2, Groups C and D; Class II,Division 1 and 2, Groups E, F, andG; and Class I, Groups A and B,Division II locations
SPECIFICATIONS
> Cast aluminum housing and ring
> Seamless steel projector
> 5" (127mm) spring steeldiaphragm
> 5 1/2" (140mm) projector
coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
B-KM-8130-G5 24V AC 60 Hz 2 48 1B-KM-8130-N5 120V AC 60 Hz .45 54 24 105B-KM-8130-R5 240V AC 60 Hz .2 48 103.2
D-0
4
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
5-25BELLS & BUZZERS
Compact single-stroke bell sounding a crisp, clean tone.
For low cost, light duty installations in factories, institutions, of-
fices, and OEMs. Uses include: doorbells, extension signals, warn-
ing bells, and audible annunciation. Ideal for end of cycle timing,
signaling, and paging.
General Purpose Bells
432 Series
Solid Brass Shell
FEATURES
> Low cost
> 2 1/2" Solid Brass Shell
> Low current drain permits longwire runs
DC Coil dB atCat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft
432-G5 24V AC 0.350 8.4 33.0 78 / 72
432-N5 120V AC 0.065 7.8 864.0 78 / 72
2 1/2"(64mm)
1 1/4"(32mm)
1 1/2"(38mm)
D-04
ELECTRONIC SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-50
Multi-Power Taps2W, 4W, 8W & 15W
Reentrant Speaker
Low power consumption, multi-watt power selection, and high sound
level output speakers
For surface mounting, use Cat. No. 5549 Surface Backbox; for
weatherproof mounting use Cat. No. 5548 Weatherproof Backbox.
They are primarily intended for use with the 5535 Remote Amplifier,
page 4-48. For use in general utility signaling applications.
Sound Pressure Level*Cat. No. Input Voltage 2W 4W 8W 15W
5547-15W 70V 90 dBA 93 dBA 96 dBA 99 dBA
*At 10 feet (3.05m) in a reverberant room using 400-4000 Hz band limited pink noise perUL 1480
4 1/4"(108mm)
4 1/4"(108mm)
Total Depth of Speaker - 3 1/4" (83mm)
5547-15WFEATURES
> Multi-watt power selection
Weatherproof installationavailable
Fungus and moisture resistant
Baked epoxy finish
UL 1480 Listed
Four power taps - 2W, 4W, 8Wand 15W
70V RMS
Frequency: 400-4,000 Hz
6" (152mm) color coded leads
© Copyright 2004 Edwards
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com5-22BELLS & BUZZERS
D
A
B
C
Compact size and pleasant sound make these bells desirable for
use in offices, apartment houses, intercom and telephone signaling,
machinery and other OEM uses.
Suitable for AC powered security systems with battery standby.
General PurposeMiniature BellsAC and DC Models
FEATURES
> 1", 2" and 3" sizes
> Long Life
> Dust proof covers
> Adjustable volume
> Grounded frame
> External binding posts
> Chrome plate finish
DC Coil dB at DimensionCat No. Size Volts Amps VA Res (ohms) 1 m / 10 ft. A B C D13-1AB 1" 5 - 10 DC 0.35 2.0 10
(25 mm) 6 - 12 AC 0.50 4.0 10 70 / 64 1 1/4" 3/4" 3 1/8" 1 3/4"13-1G1 24 DC 0.20 4.8 120 (32mm) (19mm) (79mm) (44mm)13-1G5 24 AC 0.20 4.8 8513-2AB 2" 5-10 DC 0.40 2.5 8
(51 mm) 6-12 AC 0.50 4.0 8 71 / 65 1 3/4" 1 1/16" 3 29/32" 2 1/32"13-2G1 24 DC 0.25 6.0 90 (44mm) (27mm) (99mm) (52mm)13-2G5 24 AC 0.25 6.0 5613-3AB 3" 5 - 10 DC 0.60 3.5 5
(76 mm) 6 - 12 AC 0.40 3.5 5 73 / 67 3" 1 9/16" 5 7/8" 3 1/2"13-3G1 24 DC 0.25 6 44 (76mm) (40mm) (149mm) (89mm)13-3G5 24 AC 0.25 6 30
13 Series
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Compact, dependable buzzer designed for long life and trouble-free
installations. For installation in commercial buildings, offices, and
OEM applications.
MiniatureLungenTM Buzzer
15 Series
AC and DC Models
FEATURES
> Adjustable volume
> Chrome cover; zinc plated base
DC Coil dB at DimensionCat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C D
15-0AJ 5-8V DC 0.2 1.2 106-10V AC 0.3 2.4 10 71.5 / 65.5 1 5/8" 1 15/32" 1/2" 1 13/32"
15-0G1 24V DC 0.1 2.4 120 (41mm) (37mm) (13mm) (36mm)15-0G5 24V AC 0.2 4.8 85
15-1AB 5-10V DC 0.3 2 86-12V AC 0.45 3.5 8 2 1/8" 1 13/16" 19/32" 1 53/64"
15-1E1 12V DC 0.2 2.4 20 74 / 68 (54mm) (46mm) (15mm) (46mm)15-1G1 24V DC 0.1 2.4 9015-1G5 24V AC 0.25 6 56
15-2AB 5-10V DC 3.5 2 66-12V AC 3.0 3 6 75 / 69 2 5/8" 2 3/8" 15/16" 2 3/32"
15-2G1 24V DC 0.15 3.6 60 (66mm) (60mm) (24mm) (53mm)15-2G5 24V AC 0.25 6 40
15-3AB 5-10V DC 0.3 2 56-12V AC 0.4 2.5 5 3" 2 1/2" 7/8" 2 3/8"
15-3E1 12V DC 0.2 2.4 20 80.5 / 74.5 (76mm) (64mm) (22mm) (60mm)15-3G1 24V DC 0.2 4.8 4415-3G5 24V AC 0.25 6 30
A
B C
D
5-34
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Compact, dependable buzzer designed for long life and trouble-free
installations. For installation in commercial buildings, offices, and
OEM applications.
MiniatureLungenTM Buzzer
115 Series
AC Operation
FEATURES
> Adjustable volume
> Chrome cover
> Zinc plated base
> Contact-less
DC Coil dB at DimensionCat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C D
115-1AC 8V AC 0.4 3.2 12.5 79 / 73 2 5/32" 1 9/32" 5/8" 1 25/32"115-1G5 24V AC 0.2 4.8 80 (55mm) (32mm) (16m) (45mm)
115-2AC 8V AC 0.5 4 6.5 83 / 77 2 5/8" 1 11/16" 25/32" 2 3/32"115-2G5 24V AC 0.2 4.8 45 (66mm) (43mm) (20mm) (53mm)
115-4AC 8V AC 0.45 4 3.6 86 / 80 3 7/16" 2 3/16" 1 1/8" 2 27/32"115-4G5 24V AC 0.25 6 28 (87mm) (55mm) (28mm) (72mm)
A
B C
D
5-35D
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
5-23BELLS & BUZZERS
DC Coil dB at DimensionCat No. Size Volts Amps VA Res (ohms) 1m / 10 ft. A B C55-4AM 4" 6V DC 0.85A 5.1 2.2 4" 2 1/8" 7 3/8"
(102mm) 8V AC 1.10A 8.8 2.2 74 / 68 (102mm) (54mm) (187mm)55-4G5 24V AC 0.20A 4.8 20.055-6AM 6" 6V DC 0.80A 4.8 1.9 6" 2 5/8" 10 5/8"
(152mm) 8V AC 1.00A 8.0 1.9 80 / 74 (44mm) (27mm) (99mm)55-6G5 24V AC 0.20A 4.8 24.0
B
C
A
Economy single magnet bell. Exposed striker, vibrating bell comes
with an enclosed grounded terminal and case.
For low cost, light duty installations in factories, institutions, offices,
and OEMs. Used as doorbells, extension signals, warning bells,
and audible annunciators. Especially suitable for AC powered secu-
rity systems with battery backup.
General Purpose Bells
AC and DC Models
FEATURES
> 4" and 6" gong sizes
> AC and DC Models
> Low Voltage
> Gray finish
> Low current drain permits longwire runs
55 Series
D-04
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com5-24BELLS & BUZZERS
B
A
Self-contained underdome monitor bell. Weatherproof, insulated,
and grounded vibrating bell with concealed plunger. Mounts on
3 3/4" (95mm) bolt circle.
For low cost, light duty installations in factories, institutions, offices,
and OEMs. Uses include doorbells, extension signals, warning bells
and annunciation. Suitable for AC systems with battery backup.
General Purpose Bells
156G Series
AC and DC Models
FEATURES
> 3", 4" and 6" gong sizes
> Low current drain permits longwire runs
> Supplied with weatherproofgasket for outdoor applications
> Corrosion resistant gray finish
dB at DimensionCat No. Size Volts Amps 1m / 10 ft. A B156G-3AM 3" 6-8V DC 8-10V AC 0.80156G-3AX (76 mm) 12-18V DC 0.20 3" 1 7/8"156G-3G1 24V DC 0.15 78 / 72 (76mm) (48mm)156G-3G5 24V AC 0.30156G-4AM 4" 6-8V DC 8-10V AC 0.80 4" 1 7/8"156G-4G1 (102 mm) 24V DC 0.15 82 / 76 (102mm) (48mm)156G-4G5 24V AC 0.30156G-6AM 6-8V DC 8-10V AC 0.80156G-6AW 6" 20-24V DC 0.15 86 / 80 6" 2 5/16"156G-6G1 (152 mm) 24V DC 0.15 (152mm) (59mm)156G-6G5 24V AC 0.30D
-04
ELECTRIC CHIMES
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com9-2
© Copyright 2004 Edwards
Two EntranceDoor Chimes
C210 Series
Surface mount chimes specifically designed for low cost installa-
tion. Operates from 16V transformer (purchased separately). See
page 11-2.
For use in one or two entrance homes, apartments, condominiums,
and offices.
FEATURES
> Two entrance models
> Free suspension aluminum tonebars
> Requires no lubrication
> Easy to install
> Available in white or beige
D-0
4
Economical
ELECTRIC CHIMES
ELECTRIC CHIMES
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
9-3© Copyright 2004 Edwards
D-04
2"(51mm)
3°(4 sides)
4 3/8"(111mm)
7 1/4"(184mm)
Slots top & bottom
TexturedFront
Number of EdwardsCat. No. Color Entrances Volts Amps V A Transformer
C210 Beige Two 10 1.2 12 590
C210-W White Two 10 1.2 12 590
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-52ELECTRONIC SIGNALS
Millennium Mini-MiTM
Voice & Tone Generator
The Edwards 5560M Millennium Mini-Mi is a compact tone and
voice generator which is completely modular in construction. The
5560M base unit is supplied with or without a 110 candela strobe.
One of five optional modules may be installed in the base unit.
The 5560M is configured for stand-alone operation when installed
with the 556T-M Tone Module Board. One tone may be dipswitch
selected from a field of 55 tones and will be played whenever power
is applied to the unit. When installed with the 556T-M485 Tone Mod-
ule Board, any of the available 55 tones can be activated over a
RS485 Network. For a complete listing of all 55 tones, see page
4-55.
When configured with the 556V-M Voice Module Board, the unit is
capable of stand-alone voice operation. When power is applied to
the unit it will play up to 20 seconds of one pre-recorded, field pro-
grammed voice message.
The 5560M is capable of system operation when fitted with an au-
dio coupler board. The 556A-M Audio Coupler Board allows the
Mini-Mi to be operated as a system speaker amplifier over any sys-
tem that outputs 10, 25, or 70.7 VRMS. Audio input voltage is se-
lected on the audio coupler through an onboard jumper. The 5560M
Mini-Mi may also be used as a system signal on an RS485 network
using the 556A-M485 Audio Coupler Module Board.
Diode polarized fire alarm models are available with and without the
110 candela strobe. The fire alarm models operate from 16 to 33
VDC and are available in standard white or red Lexan housings.
5560M Series
Weatherproof, durable,Multi-purpose
Compact, modular design allowsunit to be configured with tone,voice, audio coupling or RS485
10, 25 or 70.7VRMS audio inputboards available
Internal volume control
Strobe and diode polarized firealarm models
Weatherproof
UL 464
UL 1971 (AW model only)
UL 464 and 1604 Listed
NEMA Type 3R
24V AC/24V DC, 120V AC, 16-33V DC
Rugged Lexan construction
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
4-53
MOUNTING
The Mini-Mi mounts to any standard 4” (102mm)
backbox and is suitable for outdoor mounting when
mounted to the 449 backbox or any weatherproof
4" (102mm) box.
APPLICATIONS
The 5560M Mini-Mi is ideal for sounding stand-alone
or system tones and voice in factory hallway, office
and personnel areas where the use of large, horn
type devices is not desirable because of sound out-
put and appearance issues. The Mini-Mi may also be
used for fire/emergency signaling applications,
where operation and control of high decibel audio
and voice is required for plant or area-wide tone and
voice notification.
Cat. No. Color Description Voltage
5560M-AQ White Mini-Mi Base Model 24VDC or 24VAC 50/60 Hz
5560M-N5 White Mini-Mi Base Model 120VAC 50/60 Hz
5560MD-AW White Mini-Mi Base Model - Diode Polarized 16-33VDC
5560MDR-AW Red Mini-Mi Base Model - Diode Polarized 16-33VDC
5560MS-AQ White Mini-Mi Base Model with Strobe 24VDC or 24VAC 50/60 Hz
5560MS-N5 White Mini-Mi Base Model with Strobe 120VAC 50/60 Hz
5560MDS-AW White Mini-Mi Base Model with Strobe - Diode Polarized 16-33VDC
5560MDSR-AW Red Mini-Mi Base Model with Strobe - Diode Polarized 16-33VDC
556A-M N/A Audio Coupler Module Board N/A
556A-M485 N/A Audio Coupler Module Board with RS485 Connectivity N/A
556T-M N/A Tone Module Board N/A
556T-M485 N/A Tone Module Board with RS485 Connectivity N/A
556V-M N/A Voice Module Board N/A
5.06"(128.5mm)
6.56"(166.6mm)
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-12ELECTRONIC SIGNALS
Adaptatone® MillenniumMultiple Tone Signal
The Edwards 5530M Adaptatone Millennium is a heavy-duty indus-
trial, tone-selectable, signaling device capable of producing volume-
controlled, high-decibel tones. It uses a microprocessor circuit to
create 27 distinctive tones, selected by setting a dip switch within
the unit. For a complete listing of all 27 tones, see page 4-55. The
Adaptatone Millennium can be activated from field-wired, normally
open contacts, or from a 24VDC or 120VAC external voltage source
such as an output of a PLC. PLC compatibility assures no addi-
tional loading resistors or relays are required to set up your
Adaptatone.
Selected models are designed to serially connect to RS485 net-
works. The 5530MV-485Y6 additionally has a field recordable voice
feature that allows activation of voice messages over the RS485
network. See connectivity and Activation section for more detail.
Normally open contacts can be obtained from the Cat. No. 5538-4
and/or Cat. No. 5538-4R Adaptatone Signal Actuators. See pg. 4-49.
Designed for industrial applications requiring high decibel output and
microprocessor reliability. Typical applications include emergency
warning systems, plant evacuation and security intrusion alarms,
process monitoring, shift start-and-dismissal horns, and paging sig-
nals.
½" (13mm) conduit or surface mounting. See Adaptatone Signaling
Installation, page 4-56.
Single OutputRS485 Activation5530M & 5530MV Series
FEATURES
> 27 tone capability - No additionaltone modules needed
> PLC compatible
> Output up to 110 dB
> Suitable for Division 2 Locations
> Captive components
> RS485 models
AGENCY APPROVALS
> NEMA Type 3R
> UL 464 and 1604 Listed
> UL Listed for indoor and outdoorapplications in Class I, Division2, Groups A, B, C & D; Class II,Division 2, Groups F & G; andClass III Hazardous Locations
> cUL C22.2 No. 205 (24AQ, 24N5& 24Y6 models)
> CE Marked, LV & EMC Directives,(24Y6 AC & 24AQ models)
SPECIFICATIONS
> Speaker can be rotated andlocked in any horizontal direction
> 24V DC battery backup terminalsprovided
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-13
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5530M-24AQ 24V DC 24VDC 0.10 0.6424V AC 50/60 Hz 0.10 1.22
5530M-24N5 120V AC 50/60 Hz 24VDC 0.10 0.285530M-120N5 120VAC 0.10 0.28
5530M-24Y6 120V AC 50/60 Hz 24VDC 0.10 0.245530M-120Y6 240V AC 50/60 Hz 120VAC 0.10 0.15
125V DC 0.04 0.16250V DC 0.02 0.08
5530M-485Y6 120V AC 50/60 Hz RS485 0.10 0.245530MV-485Y6 240V AC 50/60 Hz 0.10 0.15(voice model) 125V DC 0.04 0.16
250V DC 0.02 0.08
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5530M-24AQ 24V DC only 2 740 8/4
5530M-24N5 120V 50/60 Hz 2 360 2.82/4
5530M-120N5 120V 50/60 Hz 5 380 2.82/4
24VDC Input Board 5V DC to 24V DC 2 6 —
120VAC Input Board 120VAC 50/60 Hz 5 13 —
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
8 47/64"(222mm)
8"(203mm)
13 3/4"(349mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
8"(203mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Edwards B-8698 & B-8699 AdaptaBuzzers are the finest, heavy
duty buzzers available. Sound is produced by the hammer action of
a vibrating armature against the cover and starts and stops instantly
with current impulse. The cover is secured to the unit's cast box by
a cast aluminum threaded ring and sealed with a neoprene gasket.
Two mounting lugs are provided for wall mounting. A 1/2" (13mm)
tapped conduit entrance is provided on one side for field wiring. Wir-
ing connections are made in the base and the cover assembly plugs
into a receptacle in the base.
Ideal for use in areas where a louder signal would be distracting.
Often used for timing, scheduling, paging, and general alarm appli-
cations. Typical indoor and weatherproof installations include con-
struction sites, shipping docks, and paper mills.
AdaptaBuzzerTM
WeatherproofDC & AC Models
DC Coil dB atCat No. Volts Amps VA Res (ohms) 1m / 10 ft.
B-8698-E1 12V DC 1.5 18 4.8 95/89B-8698-G1 24V DC 1.0 24 21.5 75 db min.B-8698-P1 125V DC 0.2 25 103B-8698-S1 240V DC 0.1 24 600
B-8699-G5 24V AC 60 Hz 1.1 26.4 5.0 95/89B-8699-N5 120V AC 60 Hz 0.2 24 146 75 db min.
B-8698 & B-8699 SeriesFEATURES
> Heavy gauge steel cover
> Die cast aluminum housing
> Vibrating armature
> Gray finish
AGENCY APPROVALS
> B-8699 Series UL 464 Listed
> NEMA Type 3R
2 holes3/8" (10mm) dia.
5 1/2"(140mm)
6 3/8"(162mm)
Tap 1/2" (13mm) IP
5 3/8"(137mm)
3"(76mm)
5-29D
-04
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
The Edwards B-KM-8140 & B-8141 series AdaptaBuzzers are qual-
ity, heavy duty AC & DC buzzers designed for use in hazardous lo-
cations. The sound is produced by the hammer action of a vibrating
armature against the cover. The buzzers are provided with two
mounting lugs for wall mounting. A 1/2" (13mm) tapped conduit en-
trance is provided on one side for field wiring. Wiring connections
are made in the base of the unit and the cover assembly plugs into
a receptacle in the base.
For use in hazardous location areas where a distinctive, lower dB
buzzer signal is required for timing, scheduling, paging, and general
alarm applications. Typical installations include petroleum plants,
gas plants, grain elevators, flour and paper mills, textile plants, and
tankers.
AdaptaBuzzerTM
B-KM-8140 & B-8141
Explosionproof
FEATURES
> Cast aluminum housing andcover
> Corrosion resistant heat flowedpowder epoxy finish
AGENCY APPROVALS
> UL 1203 Listed
2 holes3/8" (10mm) dia.
5 1/2"(140mm)
6 3/8"(162mm)
Tap 1/2" (13mm) IP
5 3/8"(137mm)
3"(76mm)
DC Coil dB atCat No. Volts Amps VA Res (ohms) 1m / 10 ft.
B-KM-8140-G5 24V AC 60 Hz 1.1 19.2 5.0 95 / 89B-KM-8140-N5 120V AC 60 Hz 0.2 24 146 75 dB min.B-KM-8140-R5 240V AC 60 Hz 0.1 24 750
B-8141-G1 24V DC 0.8 19.2 21.5 95 / 89
5-30
D-0
4
© Copyright 2004 Edwards
3-11
4VISUAL SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
The Edwards 869STR and 869DSTR AdaptaBeacon series are
bright, low current, high decibel, surface mount, combination
electronic horn/strobes for indoor, flush mount use. They have been
designed for mounting in a standard 4" (102mm) square backbox
with extension ring (total minimum depth of 3" (76mm)) (not
supplied). Strobe and horn may be operated independently.
The 869DSTR-G1 is a diode polarized 24V DC unit.
The 869STR AdaptaBeacon is for indoor flush mounting in
manufacturing sites. Used where a distinctive visual or audible
signal is required for timing, scheduling, paging, process control,
and general alarm applications.
AdaptaBeacon®
Electronic Horn/Strobe
869STR & 869DSTR
Indoor, Flush Mount
FEATURES
> Low current draw
> High dB output
> Terminals for easy wiring
> Gray flame resistant housing
> Five lens colors
> 150 candela strobe (clear lens)
> Diode polarized units available
> Engineered thermoplastichousing
> 1,000 hour strobe tube
AGENCY APPROVALS
> Strobe - UL 1638 Listed
Horn - UL 464 Listed
D-0
4
© Copyright 2004 Edwards
TECHNICAL INFORMATION
3-115VISUAL SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
CatalogNumber 869STR(*)-N5† 869STR(*)-AQ†
Operating Voltage** 120V AC 24V AC 24V DCOperating Current - Horn*** 21 mA 60 mA 20 mAOperating Current - Strobe*** 90 mA 158 mA 219 mAOperating Environment Indoor: 85% relative humidity at 86F (30C); 32F to 120F (0 to 49C) variable ambientStrobe Flash Rate 1 flash per secondSound Level Output 90 dBA at 10 ft. (3.05 m) in an Anechoic ChamberMounting Indoor Surface MountLight Output Clear Lens - 150 cd
UL 1638 Amber Lens - 90 cdGreen Lens - 70 cdRed Lens - 21 cdBlue Lens - 20 cd
*Insert lens color: C - clear, R - red, G - green, B - blue or A - amber**Operating voltage: -20% to +10% of nominal voltage***Horn and strobe currents are additive when connected in parallel.†Diode polarized units available in 24V DC. Order 869DSTR(*)-G1.
5 1/2"(140mm)
5 1/2"(140mm)
5/8"(16mm)
Mounting Plate(supplied)
Standard North American4" (102mm) sq. x 1 1/2" (38mm)deep electrical box with 1 1/2" (38mm)extension ring (not supplied)
D-04
Low cost, non adjustable bell which may be operated off of a 590
transformer or DC power. Universal economy bell widely used in
homes, apartment houses, plants, OEMs. Especially suitable for
AC powered systems with battery standby.
For office installation, see Cat. No. 13 Series Bells on page 5-22 or
Cat. No. 15 and 115 Series Buzzers on pages 5-34 and 5-35. For
combination bell and buzzer see Cat. No. 730 Dixie BuzabelTM on
page 5-38.
Nubel GeneralPurpose Bells
740 & 744 Series
AC and DC Models
C
B
A
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
BELLS & BUZZERS5-27
DC Coil dB at DimensionCat No. Volts Amps VA Res (ohms) 1m / 10 ft. A B C
740 6-8V AC 1.20 7.0 1.5 84 / 78 2 1/2" 1 1/4" 5 3/4"3-6V DC (64 mm) (32 mm) (146 mm)
744 6-8V AC 1.20 10.0 1.5 84 / 78 4" 1 3/4" 6 7/8"3-6V DC (102mm) (44mm) (175mm)
FEATURES
> AC and DC Models
> Low Voltage
> Exposed gong
> Attractive snap-on covers
> Enclosed binding posts
> Corrosion resistant metallic finish
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-6ELECTRONIC SIGNALS
Duotronic® ElectronicHorns and Sirens
The 5522 Series Horn and 5523 Series Siren are low current, high
performance, high decibel signals for hazardous locations.
They can be mounted on any surface using three bolts. Flying leads
allow for quick installation
For use where a high decibel sound is required for alert or evacua-
tion in hazardous locations. Typical applications include signaling for
security, evacuation, power failure, and danger. Ideal for use in fac-
tories, mines, flour mills, refineries and paint shops.
5522 & 5523 SeriesFEATURES
> Corrosion resistant electrostaticheat flowed powder epoxy grayfinish
> Fitted with factory sealed 1/2"(13mm) threaded pipe nipple forquick installation
AGENCY APPROVALS
> UL Listed for Class I, Division 1and 2, Groups B, C, and Dhazardous locations
> UL 464 and 1203 Listed
SPECIFICATIONS
> Speaker swivels 180° vertically orhorizontally depending onorientation of mounting bracket
> 30" (762mm) wire leads
> Horn frequency - 982 Hz
> Siren frequency - rises and fallsfrom 600 to 1250 Hz every 8seconds
Explosionproof
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-7
11 1/4"(286mm)
11 1/4"(286mm)
18 3/8"(467mm)
Speaker pivots 180°
Signal Off Signal On dB atCat. No. Description Volts Standby Current (Amps) Operating Current (Amps) 10 ft (3.05m)
5522-AQ Horn 24V DC 0.061 0.47024V AC 50/60 Hz 0.250 1.32
5522-Y6 Horn 120V AC 50/60 Hz 0,088 0.260 109240V AC 50/60 Hz 0.091 0.190
125V DC 0.031 0.130250V DC 0.019 0.070
5523-AQ Siren 24V DC 0.061 0.47024V AC 50/60 Hz 0.250 1.32
5523-Y6 Siren 120V AC 50/60 Hz 0,088 0.260 105240V AC 50/60 Hz 0.091 0.190
125V DC 0.031 0.130250V DC 0.019 0.070
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-16HORNS & SIRENS
The Edwards 876 AC & 877 DC Series are low-current, high deci-
bel, vibrating horns for heavy-duty use and is UL listed to NEMA 4X
enclosure requirements. The die-cast weatherproof box has a du-
rable, corrosion resistant, electrostatic heat flowed powder epoxy
gray finish. May be used for indoor applications.
Mount on conduit or to any flat surface. A hole on the top has been
drilled and tapped for 3/4" (19mm) - 14 NPT conduit. Knockouts are
located on the bottom and rear of the unit.
Used where a distinctive, urgent signal is required for outdoor or
weatherproof requirements such as: timing scheduling, paging, gen-
eral alarm, personnel warning, and emergency evacuations.
AdaptaHorn® Grille TypeVibrating Horn
FEATURES
> PLC compatible models
> Convenient plug-in assembly
> Corrosion resistant finish
> Completely assembled
> Volume adjustable
> NEMA 4X enclosure
AGENCY APPROVALS
> UL Listed
> FM Approved
SPECIFICATIONS
> Operating range: -20% to +10%of nominal voltage
876 AC Series
> Adjustable output: 78 to 103 dB
> 400 hour rating at 50% duty cycle
877 DC Series
> Adjustable output: 78 to 101 dB
> 200 hour rating
876 & 877 Series
Weatherproof, NEMA Type 4X
872-PO Plastic Projector
AdaptaHorn Accessory
Plastic projector snaps onto any
AdaptaHorn. Available as separate item.
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-17
4 7/8"(124mm)
Volume adjustment set screw1/16" (2mm) allen wrench supplied
3 5/16"(84mm)
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
876-E5 12V AC 1.25 15 1.5876-G5 24V AC .63 15.1 5.2 103876-N5† 120V AC .13 15.6 150876-R5 240V AC .07 16.8 580
877-E1 12V DC .27 3.2 6877-G1 24V DC .16 3.8 24877-J1 32V DC .13 4.2 40 101877-K1 48V DC .07 3.5 96877-P1 125V DC .025 3.1 600
† Diode polarized version available in red. Order 886D-N5
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppres-sion. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
PLC COMPATIBILITY - SIGNAL INPUT LOAD CHARACTERISTICS*Operating Max. off state Continuous on Surge voltage leakage current current (inrush/duration)
Cat. No. Volts mA mA Amps/milliseconds
876-N5 120V AC 25 120 1.02/.000026
877-G1 24V DC 25 150 1.7/.000042
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-6HORNS & SIRENS
The Edwards 870 AC & 871 DC Series are low-current, high decibel
flush mount vibrating horns for heavy-duty use. It has been de-
signed for wall or panel installation and projects less than 1"
(25mm) from the mounting surface. Supplied complete with trim
plate.
Designed for indoor installation. Horn mounts in Catalog No. 870-B
back box (ordered separately).
Applications include ceiling and wall mounting in corridors and
manufacturing sites. Also, ideal for scoreboards. Used wherever a
distinctive, urgent signal is required for timing, scheduling, paging,
general alarm, and warning.
AdaptaHorn® FlushMount Vibrating Horn
FEATURES
> PLC compatible models
> Corrosion resistant finish
> Volume adjustable
> Completely assembled
AGENCY APPROVALS
> UL Listed
> FM Approved (870 Series)
SPECIFICATIONS
> Operating range: -20% to +10%of nominal voltage
> Heavy duty die-cast housing
870 AC Series
> Adjustable output: 78 to 103 dB
> 400 hour rating at 50% duty cycle
871 DC Series
> Adjustable output: 78 to 101 dB
> 200 hour rating
870 & 871 Series
Indoor Applications
872-PO Plastic Projector
AdaptaHorn Accessory
Plastic projector snaps onto any
AdaptaHorn. Available as separate item.
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-7
4 1/2"(114mm)
6 1/2"(165mm)
11/16"(17mm)
2 1/4"(57mm)Volume adjustment set screw
1/16" (2mm) allen wrench supplied
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
870-G5 24V AC .63 15.1 5.2870-N5† 120V AC .13 15.6 150 103870-R5 240V AC .07 16.8 580
871-E1 12V DC .27 3.2 6.0871-G1 24V DC .16 3.8 24 101871-K1 48V DC .07 3.4 96871-P1 125V DC .025 3.1 600871-S1 250V DC .014 3.5 2640
† Diode Polarized version available in red, order 880D-N5.
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppres-sion. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
PLC COMPATIBILITY - SIGNAL INPUT LOAD CHARACTERISTICS*Operating Max. off state Continuous on Surge voltage leakage current current (inrush/duration)
Cat. No. Volts mA mA Amps/milliseconds
870-N5 120V AC 60 Hz 25 120 1.02/.000026
871-G1 24V DC 25 150 1.7/.000042
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-10HORNS & SIRENS
The Edwards 872 AC & 873 DC Series are low-current, high decibel
single projector vibrating horn for heavy-duty use. The single pro-
jector is designed to channel sound in one direction without decibel
loss. Supplied complete with Adaptaplate® for easy installation.
Supplied Adataplate allows quick plug-in connection. Horn simply
plugs into receptacle on mounting plate. Also mounts on any single
gang, 3 1/4" (83mm), 3 1/2" (89mm), 4" (102mm) octagon, or 4"
(102mm) square box.
Used in industrial, commercial, and institutional applications for tim-
ing, paging, and alarm signaling.
AdaptaHorn® SingleProjector Vibrating HornIndoor Applications
FEATURES
> PLC compatible models
> Corrosion resistant finish
> Volume adjustable
> Completely assembled
AGENCY APPROVALS
> UL Listed
> FM Approved (872 Series)
SPECIFICATIONS
> Operating range: -20% to +10%of nominal voltage
> Heavy duty die-cast housing
872 AC Series
> Adjustable output: 78 to 103 dB
> 400 hour rating at 50% duty cycle
873 DC Series
> Adjustable output: 78 to 101 dB
> 200 hour rating
872 & 873 Series
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-11
5"(127mm)
Volume adjustment set screw1/16" (2mm) allen wrench
supplied
7 1/2"(191mm)
4 1/2"(114mm)
1/2"(13mm)
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
872-E5 12V AC 1.25 15.0 1.5872-G5 24V AC .63 15.1 5.2 103872-N5† 120V AC .13 15.6 150872-R5 240V AC .07 16.8 580
873-G1 24V DC .16 3.8 24873-K1 48V DC .07 3.4 96 101873-P1 125V DC .025 3.1 600873-S1 250V DC .014 3.5 2640
† Diode polarized version available in red, order 882D-N5.
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppres-sion. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
PLC COMPATIBILITY - SIGNAL INPUT LOAD CHARACTERISTICS*Operating Max. off state Continuous on Surge voltage leakage current current (inrush/duration)
Cat. No. Volts mA mA Amps/milliseconds
872-N5 120V AC 25 120 1.02/.000026
873-G1 24V DC 25 150 1.7/.000042
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-2HORNS & SIRENS
AdaptaHorn®
Electronic Horn
The Edwards 867, 869 and 869D series are low current, high deci-
bel, surface mount, flush or panel mount electronic horns for indoor
use.
The 867 series has been designed for surface mounting with the
gray, corrosion resistant, surface mount box supplied with the unit.
The box measures 5 5/8" (143mm) square by 3 5/16" (84mm) deep.
The 869 and 869D series are designed for flush or panel mounting.
For flush mounting, they mount to a standard 4" (102mm) square
back box with extension ring (total minimum depth of 3" (76mm)).
Back box and extension ring not supplied. For panel mounting, use
only the supplied mounting plate without back box.
The 867 and 869 series electronic horns are designed for use in
corridors and manufacturing sites. It is used wherever a distinctive,
audible signal is required for timing, scheduling, general alarm, and
warning applications.
The 869D is designed for use in fire alarm systems and other appli-
cations requiring electrical supervision of signaling circuit field wir-
ing.
D-0
4
867, 869 & 869D Series
Indoor or Outdoor Surface,Flush or Panel Mount
FEATURES
> 869D diode polarized
> Low current draw
> High dB output
> Terminals for easy wiring
> May be used in outdoorapplications by using with869-WPB weatherproof back box
> 867 Series comes complete withsurface back box
> Gray Flame resistant housing
> Engineered thermoplastichousing
AGENCY APPROVALS
> UL 464 Listed
> 869D cUL Listed C22.2 No. 205
SPECIFICATIONS
> Operating voltage: -20% to +10%of nominal voltage
> Indoor Operating Environment:93% relative humidity at 104ºF(40ºC); 32ºF to 120ºF (0º to 49ºC)variable ambient
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-3D
-04
5 1/2"(140mm)
5 1/2"(140mm)
5/8"(16mm)
3 5/16"(84mm)
Mounting Plate(supplied)
5 5/8"(143mm)
5 5/8"(143mm)
Surface Mounting Box(supplied with 867 Series)
dB atCat. No. Description Volts Amps 10 ft (3.05m)
867-AQ Surface mount 24V AC 60mA 90 dBA (Anechoic chamber)24V DC 20mA
867-N5 Surface mount 120V AC 21mA 90 dBA (Anechoic chamber)
869-AQ Flush or panel mount 24V AC 60mA 90 dBA (Anechoic chamber)24V DC 20mA
869-N5 Flush or panel mount 120V AC 21mA 90 dBA (Anechoic chamber)
869D-G1 Flush or panel mount 24V DC 20mA 98 dBA (Anechoic chamber)Diode Polarized 40mA 102 dBA (Anechoic chamber)
Standard North American4" (102mm) sq. x 1 1/2" (38mm)
deep electrical box with 1 1/2" (38mm)extension ring (not supplied)
Cat. No. 869-WPBWeatherproof BackBox (not supplied)
5 59/64"(150mm)
5 59/64"(150mm)
3 13/32"(87mm)
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-8HORNS & SIRENS
The Edwards 870P AC & 871P DC Series are low-current, high
decibel panel mount vibrating horns for heavy-duty use. Supplied
complete with gasket and UL listed to NEMA 4X enclosure require-
ments.
Designed for semi-flush panel mounting, using supplied mounting
template, or installation on a 4" (102mm) square box. For NEMA
4X installation, mount to a NEMA 4X enclosure having a flat,
smooth surface using supplied 1/8" (3mm) gasket in accordance
with the installation instructions provided with the unit.
Applications include use in panel boards and switchboards wher-
ever a distinctive, urgent signal is required for timing, general alarm
& warning.
AdaptaHorn® PanelMount Vibrating Horn
870P & 871P Series
NEMA Type 4X
FEATURES
> PLC compatible models
> Corrosion resistant finish
> Volume adjustable
> Completely assembled
> NEMA Type 4X rated
AGENCY APPROVALS
> UL Listed
SPECIFICATIONS
> Operating range: -20% to +10%of nominal voltage
> Heavy duty die-cast housing
> 18" (457mm) wire with molexconnector
870P AC Series
> Adjustable output: 78 to 103 dB
> 400 hour rating at 50% duty cycle
871P DC Series
> Adjustable output: 78 to 101 dB
> 200 hour rating
872-PO Plastic Projector
AdaptaHorn Accessory
Plastic projector snaps onto any
AdaptaHorn. Available as separate item.
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-9
4 5/8"(117mm)
3 1/2"(89mm)
1 7/8"(48mm)
1"(25mm)Volume adjustment set screw
1/16" (2mm) allen wrench supplied
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
870P-E5 12V AC 1.25 15.0 1.5870P-G5 24V AC 0.63 15.1 5.2 103870P-N5 120V AC 0.13 15.6 150870P-R5 240V AC 0.07 16.8 580
871P-C1 6V DC 0.7 4.2 1.4871P-E1 12V DC 0.27 3.2 6871P-G1 24V DC 0.16 3.8 24 101871P-J1 32V DC 0.11 3.52 40871P-P1 125V DC 0.025 3.1 600871P-S1 250V DC 0.014 3.5 2640
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppres-sion. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
PLC COMPATIBILITY - SIGNAL INPUT LOAD CHARACTERISTICS*Operating Max. off state Continuous on Surge voltage leakage current current (inrush/duration)
Cat. No. Volts mA mA Amps/milliseconds
870P-N5 120V AC 25 120 1.02/.000026
871P-G1 24V DC 25 150 1.7/.000042
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-12HORNS & SIRENS
The Edwards 872DPO AC & 873DPO DC Series are low-current,
high decibel double projector vibrating horns for heavy-duty use.
The double projector is designed for bi-directional signaling without
decibel loss. Supplied complete with Adaptaplate® for easy installa-
tion.
Supplied Adataplate allows quick plug-in connection. Horn simply
plugs into receptacle on mounting plate. Also mounts on any single
gang, 3 1/4" (83mm), 3 1/2" (89mm), 4" (102mm) octagon, or 4"
(102mm) square box.
Used in industrial, commercial, and institutional applications for tim-
ing, paging, and alarm signaling. Typical applications include signal-
ing equipment malfunction, security, and employee communication.
AdaptaHorn® DoubleProjector Vibrating Horn
FEATURES
> PLC compatible models
> Corrosion resistant finish
> Volume adjustable
> Completely assembled
AGENCY APPROVALS
> UL Listed
> FM Approved (872DPO Series)
SPECIFICATIONS
> Operating range: -20% to +10%of nominal voltage
> Heavy duty die-cast housing
872DPO AC Series
> Adjustable output: 78 to 101 dB
> 400 hour rating at 50% duty cycle
873DPO DC Series
> Adjustable output: 78 to 99 dB
> 200 hour rating
872DPO & 873DPO Series
Indoor Applications
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-13
11"(297mm)
4"(102mm)
1/2"(13mm)
5"(127mm)
6 1/8"(156mm)
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
872DPO-G5 24V AC .63 15.1 5.2872DPO-N5 120V AC .13 15.6 150 101872DPO-R5 240V AC .07 16.8 580
873DPO-E1 12V DC .27 3.2 6873DPO-G1 24V DC .16 3.8 24873DPO-J1 32V DC .13 4.2 40 99873DPO-P1 125V DC .025 3.1 600873DPO-S1 250V DC .014 3.5 2640
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppres-sion. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
PLC COMPATIBILITY - SIGNAL INPUT LOAD CHARACTERISTICS*Operating Max. off state Continuous on Surge voltage leakage current current (inrush/duration)
Cat. No. Volts mA mA Amps/milliseconds
872DPO-N5 120V AC 25 120 1.02/.000026
873DPO-G1 24V DC 25 150 1.7/.000042
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-14HORNS & SIRENS
The Edwards 874AC & 875 DC Series are low-current, high decibel
surface mount vibrating horns for heavy-duty use. Supplied com-
plete with Adaptaplate® for easy installation.
Supplied Adataplate allows quick plug-in connection. Horn simply
plugs into receptacle on mounting plate. Also mounts on any single
gang, 3 1/4" (83mm), 3 1/2" (89mm), 4" (102mm) octagon, or 4"
(102mm) square box.
Used in industrial, commercial, and institutional applications for tim-
ing, paging, and alarm signaling. Applications include equipment
malfunction alert and security warning.
AdaptaHorn® Grille TypeVibrating Horn
FEATURES
> PLC compatible models
> Corrosion resistant finish
> Volume adjustable
> Completely assembled
AGENCY APPROVALS
> UL Listed
> FM Approved (874 Series)
SPECIFICATIONS
> Operating range: -20% to +10%of nominal voltage
> Heavy duty die-cast housing
> Projects only 2" (51mm) frommounting surface
874 AC Series
> Adjustable output: 78 to 103 dB
> 400 hour rating at 50% duty cycle
875 DC Series
> Adjustable output: 78 to 101 dB
> 200 hour rating
874 & 875 Series
Indoor Applications
872-PO Plastic Projector
AdaptaHorn Accessory
Plastic projector snaps onto any
AdaptaHorn. Available as separate item.
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-15
5"(127mm)
4 1/4"(108mm)
2 1/8"(54mm)
1/2"(13mm)
Volume adjustment set screw1/16" (2mm) allen wrench supplied
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
874-E5 12V AC 1.25 15.0 1.5874-G5 24V AC .63 15.1 5.2 103874-N5† 120V AC .13 15.6 150874-R5 240V AC .06 14.4 580
875-C1 6V DC 0.70 4.2 1.6875-E1 12V DC 0.27 3.2 6875-G1 24V DC 0.16 3.8 24 101875-P1 125V DC 0.025 3.1 600875-S1 250V DC 0.014 3.5 2640
† Diode polarized version available in red. Order 884D-N5
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
Electromechanical devices can produce transient spikes and should only be used on PLC output cards that have inherent transient spike suppres-sion. Consult the PLC manufacturer prior to connecting 24V DC electromechanical devices to PLCs.
PLC COMPATIBILITY - SIGNAL INPUT LOAD CHARACTERISTICS*Operating Max. off state Continuous on Surge voltage leakage current current (inrush/duration)
Cat. No. Volts mA mA Amps/milliseconds
874-N5 120V AC 25 120 1.02/.000026
875-G1 24V DC 25 150 1.7/.000042
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-18HORNS & SIRENS
The Edwards 878EX AC & 879EX DC Series are heavy-duty, high
decibel, vibrating horn signals designed for use in hazardous loca-
tions.
Two mounting brackets are provided on either side of the unit for
wall mounting. The housing is tapped on one side for 3/4" (19mm)
conduit to allow for field wiring installation.
For use in dusty, hazardous atmospheres where a distinctive, ur-
gent signal is required for timing, scheduling, paging and general
alarm applications. Typical applications include use in mines, petro-
leum plants, gas plants, grain elevators, flour mills, paper mills, tex-
tile plants and tankers.
AdaptaHorn® Grille TypeHazardous Location Horn
FEATURES
> Corrosion resistant heat flowedepoxy finish
> Low current drain
AGENCY APPROVALS
> UL Listed for Class I, Division 1and 2, Groups B, C, and D; ClassII, Division 1 and 2, Groups E, F,and G; and Class III locations
> UL Listed for outdoor locations
> NEMA Type 4X Rated
SPECIFICATIONS
> Wide operating voltage range-20% to +10% of nominal voltage
> Power connection wiresembedded in sealing compound
878EX & 879EX Series
Outdoor Rated, NEMA Type 4X
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-19
Markmounting
holes
(2) Mounting bracketsfor 3/8" (10mm) diameter
maximum fasteners
Explosion-proof conduitoutlet box (not supplied)
3/4" (19mm) conduit(not supplied)
7 3/8"± 1/8"(187mm ± 3mm)
2 1/4"(57mm)
6 1/2"(165mm)
4 3/16"(106mm)
7 5/8"(194mm)
3/4" (19mm)14NPT nipple
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
878EX-E5 12V 50/60 Hz 1.25 15 1.45878EX-G5 24V 50/60 Hz 0.625 15 5.2 97878EX-N5 120V 50/60 Hz 0.13 15 150.0878EX-R5 240V 50/60 Hz 0.065 15.6 580.0
879EX-C1 6V DC 0.70 4.2 1.4879EX-E1 12V DC 0.27 3.2 6.0879EX-G1 24V DC 0.16 3.8 24.0879EX-J1 32V DC 0.13 3.2 40.0 97879EX-K1 48V DC 0.07 3.4 96.0879EX-P1 125V DC 0.025 3.1 600.0
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-20HORNS & SIRENS
The Edwards 878DEX AC & 879DEX DC Series are diode
polarized, heavy-duty, high decibel, vibrating horn signals. They
are intended for use in hazardous locations requiring electrical
supervision of signaling circuit field wiring. May also be used for
unsupervised signaling applications.
Two mounting brackets are provided on either side of the unit for
wall mounting. The housing is tapped on one side for 3/4" (19mm)
conduit to allow for field wiring installation.
For use in dusty, hazardous atmospheres where a distinctive,
urgent signal is required. Typical applications include use in mines,
petroleum plants, gas plants, grain elevators, flour mills, paper
mills, textile plants and tankers.
FEATURES
> Diode polarized
> Corrosion resistant heat flowedepoxy finish
> Low current drain
AGENCY APPROVALS
> UL Listed for Class I, Division 1and 2, Groups B, C, and D; ClassII, Division 1 and 2, Groups E, F,and G; and Class III locations
> UL Listed for outdoor locations
> NEMA Type 4X Rated(Outdoor Type 4x applies togeneral signaling use in non-firealarm applications)
> CSA version available
SPECIFICATIONS
> Wide operating voltage range-20% to +10% of nominal voltage
> Power connection wiresembedded in sealing compound
878DEX & 879DEX Series
AdaptaHorn® Grille TypeHazardous Location HornDiode Polarized,Outdoor Rated, NEMA Type 4X
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-21
Markmounting
holes
(2) Mounting bracketsfor 3/8" (10mm) diameter
maximum fasteners
Explosion-proof conduitoutlet box (not supplied)
3/4" (19mm) conduit(not supplied)
7 3/8"± 1/8"(187mm ± 3mm)
2 1/4"(57mm)
6 1/2"(165mm)
4 3/16"(106mm)
7 5/8"(194mm)
3/4" (19mm)14NPT nipple
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
878DEX-N5 120V AC 0.13 15.6 150.0 97
879DEX-G1† 24V DC 0.16 3.8 20.0 97
† Diode polarized version available in red. Order 889D-AW
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-22HORNS & SIRENS
The Edwards B-N-8546 AC and B-8526 DC Series are designed for
use where a loud and distinctive signal is needed. The sound
mechanism of the signal starts and stops instantly with current im-
pulse. The projector is connected to the heavy duty die cast alumi-
num housing by a cast aluminum, threaded ring.
Two mounting lugs are provided on either side of the unit for wall
mounting. The housing is tapped on one side for 1/2" (13mm) con-
duit to allow for field wiring installation.
Used where directional sound dispersion is required or specified.
Applications include timing, scheduling, paging, and general alarm
at construction sites, textile and paper mills, lumber yards, and
shipping docks.
AdaptaHorn® SingleProjector Horn
B-8526 & B-N-8546 Series
Weatherproof, NEMA Type 4X
FEATURES
> Convenient plug-in assembly
> Corrosion resistant heat flowedepoxy finish
> Completely assembled
> Gasket sealed
> External volume control screw
AGENCY APPROVALS
> UL Listed NEMA Type 4Xenclosure
SPECIFICATIONS
> Heavy duty die cast aluminum
> 7" (178mm) seamless steelprojector
> Vibrating diaphragm
> Tungsten contacts with arcsuppressor (B-8526)
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-23
5 1/2"(140mm)
6 3/8"(162mm)
9 1/2"(241mm)
13/16"(21mm)
2 holes3/8" (10mm) Tap 1/2" (13mm)
5 1/8"(130mm)
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
B-N-8546-E5 12V AC 1.6 19.2 3B-N-8546-G5 24V AC 1.1 26.4 5 97B-N-8546-N5 120V AC .2 24 146B-N-8546-R5 240V AC .1 24 750
B-8526-G1 24V DC 1 24 21.5 95B-8526-P1 125V DC .2 25 103B-8526-S1 250V DC .1 25 600
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-24HORNS & SIRENS
The Edwards B-N-8590 AC & B-8599 DC Series vibrating horns are
designed for use where a loud and distinctive signals are needed.
The sound mechanism of the signal starts and stops instantly with
current impulse. The projector is connected to the heavy duty die
cast aluminum housing by a cast aluminum, threaded ring.
Two mounting lugs are provided on either side of the unit for wall
mounting. The housing is tapped on one side for 1/2" (13mm) con-
duit to allow for field wiring installation.
Used where sound dispersion in opposite directions is required or
specified. Applications include timing, scheduling, paging, and gen-
eral alarm at construction sites, textile and paper mills, lumber
yards, and shipping docks.
AdaptaHorn® DoubleProjector Horn
FEATURES
> Convenient plug-in assembly
> Corrosion resistant heat flowedepoxy finish
> Completely assembled
> Gasket sealed
> External volume control screw
AGENCY APPROVALS
> UL Listed 60 Hz (B-N-8590)
> UL Listed NEMA Type 4Xenclosure
SPECIFICATIONS
> Heavy duty die cast aluminum
> 7" (178mm) seamless steelprojector
> Vibrating diaphragm
> Tungsten contacts with arcsuppressor (B-8599)
B-N-8590 & B-8599 Series
Weatherproof, NEMA Type 4X
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-25
5 1/8"(130mm)
2 holes 3/8" (10mm)
Tap 1/2" (13mm) IP
17 3/4"(451mm)
7 1/8"(181mm)
3/16" (21mm)
5 1/2"(140mm)
DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.
B-N-8590-E5 12V AC 1.6 19.2 3B-N-8590-G5 24V AC 1.1 26.4 5 95B-N-8590-N5 120V AC .2 24 146
B-8599-E1 12V DC 1.5 18 3B-8599-G1 24V DC 1 24 21.5 93B-8599-P1 125V DC .2 25 103B-8599-S1 250V DC .1 25 600
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-34ELECTRONIC SIGNALS
Adaptatone® MillenniumSystem Master
The Edwards 5541M Millennium System Master is a fully super-
vised personnel notification control system for both emergency fa-
cility evacuation, and non-emergency process control and plant-
wide signaling communications.
The System Master may be used for ancilliary Fire Alarm evacua-
tion by tying into an existing fire alarm system.
The 5532M Series Speaker/Amplifier is used for sound output. Up
to 200 speaker/amplifiers can be connected to the system master.
The System Master is simple to program and operate using a nine-
button keypad and an easy-to-read, 40-character LCD display, with
Dynamic Zone Control (DZC™). DZC enables zone reconfiguration
through a series of simple keystrokes without the need for expen-
sive system rewiring. The System Master may be remotely pro-
grammed from a PC using available software.
Employing both voice and tone to alert, warn and communicate, the
System master features 68 built-in tones, hand-held microphone
operation, and stores up to four, five-second, field-recordable voice
messages for playing over remote speakers. PBX phone paging is
included, so no separate telephone paging system is required. The
Millennium System Master meets all OSHA self-monitoring,
prioritization and standby power requirements, plus the latest UL
standards for evacuation signaling.
MEDI compatible. See page 4-10.
5541M Series
Evacuation & Plant-wideSignaling, RS485 Activation
FEATURES
> 68 tones
> 4 zone control with zone paging
> Audio, voice & power supervision
> Microphone & external inputsupervision
> Up to 4 5-second voice messagesor one 20-second message
> Remote programming anddiagnostics
> Phone paging from PBX systems
> Up to 64 satellite units addressablethrough RS485
> Output and trouble relays designedfor fail-safe operation
> Top, side and bottom knockoutsfor easy wire entry
> LED alarm, standby power &status indications
> Activates LED text displays
> Easy to adjust audio output
AGENCY APPROVALS
> OSHA approved
> UL 2017 Listed for Emergency SelfMonitored Use
> UL 864 and UL 1711 Listed
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-35
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5541M-Y6 120V AC 60 Hz .14 .37240V AC 50 Hz .10 .22
18 1/4"(464mm)
4 5/8"(117mm)
14"(356mm)
Typical Adaptatone System Master Configuration
D-04
Up to 64 RS-485 devices(satellite panels or Adaptatone Millennium Units)
Up to 25 Multiple5542RPU's Input
(see manual)
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-28ELECTRONIC SIGNALS
Adaptatone® MillenniumCentral Tone Generator
The Edwards 5540M Millennium Central Tone Generator has been
designed for applications where simultaneous signaling of a high
decibel, heavy duty signal is required. The tone generator assures a
synchronous signaling sound from all remote speakers. The Millen-
nium Central Tone Generator produces the 27 standard Adaptatone
sounds. Four tones may be activated from field-wired, normally
open contacts, or a 24VDC or 120VAC external voltage source
such as an output of a PLC.
Normally open contacts can be obtained from the Cat. No. 5538-4 or
Cat. No. 5538-4R Adaptatone Signal Actuator. See page 4-49. The
tones are selected by setting miniature dip switches within the unit.
The programmed tones operate on a pyramid-type priority system.
For more information on priority tone operation and a complete list-
ing of all 27 tones, see page 4-55.
On-site volume control is accomplished by adjusting the conve-
niently located volume control inside the unit.
The 5540M-485Y6 is designed to be connected to RS485 networks,
allowing full serial signaling communication control.
Adaptatone Signaling Systems are designed for industrial applica-
tions calling for high decibel output and microprocessor reliability
combined with simultaneous signal delivery over all speakers in-
cluded in the system. Typical applications include: emergency
warning systems, plant evacuation alarms, security intrusion si-
rens, process monitoring, shift start-and-dismissal horns, and pag-
ing signals.
RS485 units are MEDI compatible. See page 4-10.
5540M Series
Synchronized System Signaling,Four Outputs, RS485 Activation
FEATURES
> 27 tone capability - No additionaltone modules needed
> PLC Compatible
> Captive Components
> Centralized programmable toneselection
> System-wide priority toneselection
> RS485 models available
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL Listed for indoor and outdoorapplications in Class I, Div. 2,Groups A, B, C & D; Class II, Div.2, Groups F & G; and Class IIIhazardous locations
> cUL C22.2 No. 205 (24AQ, 24N5& 24Y6 models)
> TUV Rheinland Certified
> CE Marked - Cenelec LV & EMCDirectives (24Y6 AC only &24AQ models)
SPECIFICATIONS
> 24V DC battery backup terminals
> Short Circuit protectedD-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-29
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5540M-24AQ 24V DC 24VDC 0.10 0.7424V AC 50/60 Hz 0.10 1.3
5540M-24N5 120V AC 50/60 Hz 24VDC 0.10 0.365540M-120N5 120V AC 50/60 Hz 120VAC 0.10 0.38
5540M-24Y6 120V AC 50/60 Hz 24V DC 0.10 0.32240V AC 50/60 Hz 0.10 0.20
125V DC 0.10 0.21250V DC 0.02 0.10
5540M-120Y6 120V AC 50/60 Hz 120VAC 0.10 0.31240V AC 50/60 Hz 0.10 0.20
125V DC 0.10 0.20250V DC 0.02 0.10
5540M-485Y6 120V AC 50/60 Hz RS485 0.10 0.31240V AC 50/60 Hz 0.10 0.20
125V DC 0.10 0.20250V DC 0.02 0.10
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5540M-24AQ 24V DC only 2 740 8/4
5540M-24N5 120V 60 Hz 2 360 2.82/4
5540M-120N5 120V 60 Hz 5 380 2.82/4
5540M-24Y6 120V 60 Hz 2 320 2.82/4
5540M-120Y6 120V 60 Hz 5 310 2.82/4
24VDC Input Board 24V DC (each input) 2 6 —
120VAC Input Board 120VAC 60 Hz (each input) 5 13 —
Mounting flange4 holes (2 each side)
2 1/2"(64mm)
6"(152mm)
4"(102mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
3 1/2"(89mm)
D-04
© Copyright 2004 Edwards
3-11
0VISUAL SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
The Edwards 867STR AdaptaBeacon series is a bright, low current,
high decibel, surface mount, combination electronic horn/strobe for
indoor use. It has been designed for mounting with the supplied
back box. Strobe and horn may be operated independently.
The 867STR mounts to the gray, corrosion resistant surface box
supplied with the unit. The box measures 5 5/8" (143mm) square by
3 5/16" (84mm) deep.
The 867STR AdaptaBeacon is for indoor wall mounting in
manufacturing sites. Used where a distinctive visual or audible
signal is required for timing, scheduling, paging, process control,
and general alarm applications.
AdaptaBeacon®
Electronic Horn/Strobe
867STR Series
Indoor, Surface Mount
FEATURES
> Low current draw
> High dB output
> Terminals for easy wiring
> Gray flame resistant housing
> Five lens colors
> 150 candela strobe (clear lens)
> Complete with gasket and surfaceback box
> Engineered thermoplastichousing
> 1,000 hour strobe tube
AGENCY APPROVALS
> Strobe - UL 1638 Listed
Horn - UL 464 Listed
D-0
4
© Copyright 2004 Edwards
TECHNICAL INFORMATION
3-111VISUAL SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
CatalogNumber 867STR(*)-N5 867STR(*)-AQ
Operating Voltage** 120V AC 24V AC 24V DCOperating Current - Horn*** 21 mA 60 mA 20 mAOperating Current - Strobe*** 90 mA (RMS) 158 mA (RMS) 219 mA (AVG)Operating Environment Indoor: 85% relative humidity at 86F (30C); 32F to 120F (0 to 49C) variable ambientStrobe Flash Rate 1 flash per secondSound Level Output 90 dBA at 10 ft. (3.05 m) in an Anechoic ChamberMounting Indoor Surface MountLight Output Clear Lens - 150 cd
UL 1638 Amber Lens - 90 cdGreen Lens - 70 cdRed Lens - 21 cdBlue Lens - 20 cd
*Insert lens color: C - clear, R - red, G - green, B - blue or A - amber**Operating voltage: -20% to +10% of nominal voltage***Horn and strobe currents are additive when connected in parallel.
5 1/2"(140mm)
5 1/2"(140mm) 5/8"
(16mm)
3 5/16"(84mm)
Mounting Plate(supplied)
5 5/8"(143mm)
5 5/8"(143mm)
Surface Box(supplied)
D-04
© Copyright 2004 Edwards
3-11
2VISUAL SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
The Edwards 868STR AdaptaBeacon series is a bright, low current,
high decibel, surface mount, combination electronic horn/strobe for
indoor or outdoor use. It has been designed for mounting with the
supplied back box. Strobe and horn may be operated independently.
The 868STR mounts to the gray, corrosion resistant weatherproof
surface box supplied with the unit. The box measures 5 59/64"
(150mm) square by 3 13/32" (87mm) deep.
The 868STR AdaptaBeacon is for outdoor wall mounting in
manufacturing sites. Used where a distinctive visual or audible
signal is required for timing, scheduling, paging, process control,
and general alarm applications.
AdaptaBeacon®
Electronic Horn/Strobe
868STR Series
Outdoor, Surface Mount
FEATURES
> Low current draw
> High dB output
> Terminals for easy wiring
> Gray flame resistant housing
> Five lens colors
> 150 candela strobe (clear lens)
> Complete with gasket andweatherproof surface back box
> Engineered thermoplastichousing
> 1,000 hour strobe tube
AGENCY APPROVALS
> Strobe - UL 1638 Listed
Horn - UL 464 Listed
D-0
4
© Copyright 2004 Edwards
TECHNICAL INFORMATION
3-113VISUAL SIGNALS
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
CatalogNumber 868STR(*)-N5 868STR(*)-AQ
Operating Voltage** 120V AC 24V AC 24V DCOperating Current - Horn*** 21 mA 60 mA 20 mAOperating Current - Strobe*** 90 mA (RMS) 158 mA (RMS) 219 mA (AVG)Operating Environment Indoor: 85% relative humidity at 86F (30C); 32F to 120F (0 to 49C) variable ambient
Outdoor: 95% relative humidity at 86F (30C); -31F to 150F (-35C to 66C) variable ambientStrobe Flash Rate 1 flash per secondSound Level Output 90 dBA at 10 ft. (3.05 m) in an Anechoic ChamberMounting Outdoor Surface MountLight Output Clear Lens - 150 cd
UL 1638 Amber Lens - 90 cdGreen Lens - 70 cdRed Lens - 21 cdBlue Lens - 20 cd
*Insert lens color: C - clear, R - red, G - green, B - blue or A - amber**Operating voltage: -20% to +10% of nominal voltage***Horn and strobe currents are additive when connected in parallel.
5/8"(16mm)
5 59/64"(150mm)
Mounting Plate(supplied)
5 59/64"(150mm)
3 13/32"(87mm)
5 1/2"(140mm)
5 1/2"(140mm)
WeatherproofSurface Box
(supplied)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-16ELECTRONIC SIGNALS
Adaptatone® MillenniumMultiple Tone Signal
The Edwards 5530MHV Adaptatone Millennium is a heavy-duty,
high volume, 30 watt, industrial signaling device capable of produc-
ing volume-controlled, high-decibel tones. It uses a microprocessor
circuit to create 27 distinctive tones. A single tone may be selected
by setting a miniature switch within the unit. For a complete listing
of all 27 tones, see page 4-55.
The Adaptatone Millenium can be activated from field-wired, nor-
mally open contacts, or a 24VDC or 120VAC external voltage
source such as an output of a PLC. Normally open contacts can be
obtained from the 5538-4 and/or 5538-4R Adaptatone Signal Actua-
tors. See page 4-49.
The 5530MHV-485Y6 is designed to be connected to RS485 net-
works, allowing full serial signaling communication control.
Designed for industrial applications. Typical applications include
emergency warning systems, plant evacuation and security intru-
sion alarms, process monitoring, shift start-and-dismissal horns,
and paging signals.
The 5530MHV is designed for either 1/2" (13mm) conduit or surface
mounting. See Adaptatone Signaling Installation, pages 4-56.
30 Watt High Volume, SingleOutput, RS485 Activation5530MHV Series
FEATURES
> 27 tone capability - No additionaltone modules needed
> Output up to 113 dB @ 10 ft
> PLC compatible
> Suitable for Division 2 Locations
> Captive Components
> RS485 model available
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL Listed for indoor and outdoorapplications in Class I, Division2, Groups A, B, C & D; Class II,Division 2, Groups F & G; andClass III Hazardous Locations
> cUL C22.2 No. 205 (24AQ, 24N5& 24Y6 models)
> TUV Rheinland Certified
> CE Marked, LV & EMC Directives,(24Y6 AC only & 24AQ models)
SPECIFICATIONS
> Speaker can be rotated andlocked in any horizontal direction
> 24V DC battery backup terminalsprovided
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-17
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5530MHV-24AQ 24V DC 24VDC 0.10 1.2224V AC 50/60 Hz 0.10 2.21
5530MHV-24Y6 120V AC 50/60 Hz 24VDC 0.10 0.635530MHV-120Y6 240V AC 50/60 Hz 120VAC 0.07 0.30
125V DC 0.04 0.37250V DC 0.02 0.17
5530MHV-485Y6 120V AC 50/60 Hz RS485 0.10 0.63240V AC 50/60 Hz 0.07 0.30
125V DC 0.04 0.37250V DC 0.02 0.17
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5530MHV-24AQ 24V DC only 2 740 8/4
24VDC Input Board 5V DC to 24V DC 2 6 —
120VAC Input Board 120VAC 50/60 Hz 5 13 —
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
11 1/2"(292mm)
9 3/4"(248mm)
15"(381mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
9 3/4"(248mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-4ELECTRONIC SIGNALS
Low current, high performance, high decibel signaling appliance de-
signed to function as either a horn or siren by setting an internal,
tamper proof switch. The 5520D is primarily intended for use in ap-
plications requiring electrical supervision of signaling circuit field
wiring. These signals may also be used for unsupervised signaling
applications.
The signal's universal Adaptaplate® mounts directly on walls, or on
any single-gang opening. Adaptaplate speeds installation by allow-
ing the installer to connect all field wiring to the plate and then fin-
ishing the installation by snapping the horn onto the plate. It also
mounts to 3 1/4" (83mm), 3 1/2" (89mm), 4" (102mm) octagon, 4"
(102mm) square boxes, or equivalent fittings. The signal may be
weatherproofed using the Edwards Cat. No. 349 back box (see page
5-10).
Used for schools, factories, lumber yards, and commercial installa-
tions. The horn signal is often used for timing, paging, and burglar
and fire alarms. The siren signal is particularly suitable for alarm
and evacuation in high noise areas.
Duotronic®
Horn/Siren
5520D Series
Diode Polarized, High dB
FEATURES
> Diode polarized for supervisorycircuits
> Weatherproofed by adding 349back box
> Switchable horn or sirenoperation
> Easy Adaptaplate installation
AGENCY APPROVALS
> UL 464 Listed
> FM Approved Audible NotificationAppliances Standard 3151-3152
SPECIFICATIONS
> Speaker swivels 180° horizontallyand 90° vertically
> Horn frequency - 1.1KHz
> Siren frequency - rises and fallsfrom 600 to 1300 Hz every 3seconds
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-5
11"(279mm)
8 3/4"Dia.(222)
14"(356mm)
7" Dia.(178mm)
5 1/2"(140mm)
13 1/2"(343mm)
11"(279mm)
90°
Speaker can bepositioned anywherewithin 90° vertically
and 180° horizontallyMay be weatherproofed using Cat. No. 349 back box (not supplied)
dB atCat. No. Volts Amps VA 10 ft (3.05m)
5520D-N5 120V AC .35 42.0 11450/60 Hz (Horn)
5520D-AW 20-24V DC .35 8.4 112(Siren)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-4HORNS & SIRENS
AdaptaHorn®
Electronic Horn
The Edwards 868 series is a low current, high decibel, weatherproof
surface mount, electronic horn for outdoor or indoor use. It has
been designed for mounting with the supplied weatherproof back
box.
The 868 mounts, using the supplied gasket, to the gray, corrosion
resistant weatherproof surface box supplied with the unit. The box
measures 5 59/64" (150mm) square by 3 13/32" (87mm) deep.
The 868 electronic horn is for indoor and outdoor use wherever a
distinctive, audible signal is required for timing, scheduling, general
alarm, and emergency warning applications.
868 Series
Outdoor Surface Mount
FEATURES
> Low current draw
> High dB output
> Terminals for easy wiring
> Gray Flame resistant housing
> Complete with gasket andweatherproof surface back box
> Engineered thermoplastichousing
AGENCY APPROVALS
> UL 464 Listed
SPECIFICATIONS
> Operating voltage: -20% to +10%of nominal voltage
> Outdoor Operating Environment:98% relative humidity at 104ºF(40ºC); -31ºF to 150ºF (-35º to66ºC) variable ambient
D-0
4
HORNS & SIRENS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
6-5
Weatherproof BackBox (supplied)
5/8"(16mm)
5 59/64"(150mm)
Mounting Plate(supplied)
5 59/64"(150mm)
3 13/32"(87mm)
5 1/2"(140mm)
5 1/2"(140mm)
dB atCat. No. Volts Amps 10 ft (3.05m)
868-AQ 24V AC 60mA 90 dBA (Anechoic chamber)24V DC 20mA
868-N5 120V AC 21mA 90 dBA (Anechoic chamber)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-28
Motor DrivenIndustrial Siren
Heavy duty, industrial design, motor driven siren that emits a con-
tinuous loud piercing wail.
Mounts to any solid surface using two bolts. May be swiveled
through 180°, vertically or horizontally, depending on orientation of
bracket.
Used for initial installation and MRO applications in factories, lum-
ber yards, security installations, and score boards.
315A-AH
Heavy Duty, Outdoor
FEATURES
> Fully enclosed motor
> Weatherproof
> Adjustable siren direction
> AC or DC operation
AGENCY APPROVALS
> UL Listed for continuous duty
SPECIFICATIONS
> 2.5 amp motor
> Heavy gauge aluminumconstruction
> Frequency 1100 Hz
8 1/4"(210mm)
4"(102mm)
6 7/8"(175mm)
15 11/32"(390mm)
Two 9/32"(7mm)
mountingholes
7 1/2" dia.(191mm)
8 1/2" dia.(216mm)Two nuts. Loosen
to adjust siren direction
dB atCat. No. Volts Amps V A 10 Ft.
315A-AH 120V AC/DC 2.5 300 110
HORNS & SIRENSD
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
6-29
Klaxon®
Klaxet Signals
The Edwards KLAX series is an indoor, projector type signal. The
KLAX sounds the unique Klaxon tone. The sound is produced by
the revolution of a serrated rotor against a hardened steel stud riv-
eted to the center of a diaphragm.
The KLAX is designed for bracket mounting using the supplied
bracket. Field wiring is connected through the 1/2" (13mm) conduit
connection.
Designed for use in high noise environments such as machine and
heavy equipment areas. Uses include equipment start and stop,
general warning, and equipment breakdown.
KLAX Series
Motor Driven
3 1/16"(78mm)
10 25/32"(274mm)
3 3/16"(81mm)
4 3/8"(111mm)
1 hole13/32" (10mm)
1/2" (13mm) - 14 NPTconduit opening (both sides)
2 holes3/8" (10mm)
Adjustingarm
and capnut
Cat. No. Volts Current
KLAX-G5 24V AC 50/60 Hz 2.5A
FEATURES
> Completely assembled
> Rugged, heavy-duty design
> Complete with mounting bracket
> Automatic resettable overloadprotection
AGENCY APPROVALS
> UL Listed
SPECIFICATIONS
> 101dB at 10 ft
> Frequency - 470 Hz
> Rated for intermittent use -1 minute on, 5 minutes off
HORNS & SIRENSD
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com6-30
Klaxon®
Motor Driven Siren
The MONO series is a small weatherproof motor driven siren. This
siren’s unique output signal may be pulsed on and off to achieve a
wailing tone. The siren's sound is produced by a multi-bladed, nylon
impeller which pulls air through openings located on the front of the
unit and pushes the air out through radially positioned vents.
The MONO is designed for bracket mounting using the housing
bracket. The signal is supplied with wire leads for connection in an
appropriate electrical box.
Designed for outdoor use. Applications include local weather and
emergency warning, and area evacuation.
MONO Series
Weatherproof
KLAXON is a registered trademarkof Klaxon Signals Ltd.
1 1/2(38)
1 1/2(38)
3 (76)
2 1/2"(64mm)
2 Holes 9/32" (7mm) Dia.
3 3/4" Dia.(95mm)
1/2" - 14NPT
3 3/4"(95mm)
1 37/64"(40mm)
2 23/64"(60mm)
1 13/16"(46mm)
7 1/8"(181mm)
3 1/4"(83mm)
3 15/64"(82mm)
1 1/4"(32mm)1 3/4"
(44mm)
Cat. No. Volts Current
MONO-AQ 24V AC 50/60 Hz 4.6A24V DC 3.6A
MONO-AH 120V AC 50/60 Hz 1.0A120V DC 0.9A
FEATURES
> Completely assembled
> May be pulsed for wailing tone
> Complete with mounting bracket
> Automatic resettable overloadprotection
SPECIFICATIONS
> 106dB at 10 ft
> Frequency - 1800 Hz
> Rated for continuous use
HORNS & SIRENSD
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
6-33
The MTS-Y1 is a durable, multi-application DC audible signal de-
signed for indoor applications requiring on site tone modification.
This signal has nine selectable sound patterns: continuous tone,
slow warble, fast warble, low shriek, high shriek, slow pip, fast pip,
slow two tone and fast two tone.
The MTS-Y1 is designed for mounting using the knockouts in the
high impact, ABS case. See illustration below.
The MTS-Y1 is designed for indoor applications requiring on site
tone modification.
Klaxon®
Multi-Tone Signal
MTS-Y1FEATURES
> Small compact design
> Completely assembled
> Choice of 9 field selectable tones
> Complete with mounting bracket
SPECIFICATIONS
> 90dB at 10 ft (3.05m)
> Frequency - 700-950Hz
> Rating - Continuous
KLAXON is a registered trademarkof Klaxon Signals Ltd.
3 11/32"(85mm)
4 1/10"(104mm)
1 31/32"(50mm)
2 11/32"(60mm)4 knockouts
3/16" (5mm)
2 slots forcountersunk
screw mounting3/16" (5mm)
minor diameter
2 11/32"(60mm)
1 31/32"(50mm)
Cat. No. Volts Current
MTS-Y1 12/24V DC 8 mA
HORNS & SIRENSD
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-24ELECTRONIC SIGNALS
Adaptatone®
Electronic Signal
The Edwards 5533M Adaptatone Signal is an explosionproof,
heavy-duty industrial, tone-selectable, signaling device capable of
producing volume-controlled, high-decibel tones. The signal ac-
cepts up to two contact closures and delivers two audible output
signals selected from the 55 tones available. The two tones may
be selected by setting miniature switches within the unit. One of
the tones can be assigned a priority status to override the other
tone. For more information on priority tone operation and a complete
listing of all 55 tones, see page 4-55.
The electrical inputs activating the Adaptatone Signal are received
from field-wired, normally open contacts or from the Cat. No. 5538-4
Adaptatone Signal Actuator. (Not suitable for hazardous locations.)
See page 4-49.
The 5533M Adaptatone mounts on any surface using three bolts.
See Adaptatone Signaling Installation, pages 4-56.
For use where a high decibel sound is required for alert or evacua-
tion in hazardous locations. Typical applications include signaling
use in mining, granaries, flour mills, tankers, refineries, laboratories,
spray booths, and other hazardous locations.
5533M SeriesFEATURES
> 55 tone capability - No additionaltone modules needed
> Internal volume control
> Corrosion resistant heat flowedepoxy finish
> Supplied with factory sealed 1/2"(13mm) threaded fitting for quickinstallation
AGENCY APPROVALS
> UL 464 and 1203 Listed
> UL Listed for Class I, Division 1and 2, Groups B, C, and Dhazardous locations
SPECIFICATIONS
> Speaker swivels 180° vertically orhorizontally depending onorientation of mounting bracket
> 30" (762mm) numbered wireleads
> Heavy duty zinc cast construction
Explosionproof, Two Outputs
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-25
Horn pivots one way 180°
11 1/4"(286mm)
11 1/4"(286mm)
18 3/8"(467mm)
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5533M-AQ 24V DC 0.061 0.47036V DC 0.077 0.600
24V AC 50/60 Hz 0.250 1.320
5533M-Y6 120V AC 50/60 Hz 0.088 0.260240V AC 50/60 Hz 0.091 0.190
125V DC 0.031 0.130250V DC 0.019 0.070
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-26ELECTRONIC SIGNALS
Adaptatone®
Electronic Signal
The Edwards 5533MD Adaptatone Signal is an explosionproof,
heavy-duty industrial, tone-selectable, signaling device capable of
producing volume-controlled, high-decibel tones. The signal deliv-
ers one audible output signal selected from the 55 tones available.
The tone may be selected by setting a miniature switch within the
unit. For more information on priority tone operation and a complete
listing of all 55 tones, see page 4-55.
The 5533MD Adaptatone mounts on any surface using three bolts.
See Adaptatone Signaling Installation, pages 4-56.
The 5533MD Adaptatone is designed hazardous location applica-
tions requiring electrical supervision of signaling circuit field wiring.
The signal may also be used for unsupervised signaling applica-
tions. Typical applications include signaling use in mining, grana-
ries, flour mills, tankers, refineries, laboratories, spray booths, and
other hazardous locations.
5533MD
Explosionproof, DiodePolarized, Single Output
FEATURES
> Stand-alone. 55 tone capability -No additional tone modulesneeded
> Diode polarized for supervisedsignaling circuits
> Internal volume control
> Corrosion resistant heat flowedepoxy finish
AGENCY APPROVALS
> UL 464 and UL1203
> UL Listed for Class I, Division 1and 2, Groups B, C, and Dhazardous locations
SPECIFICATIONS
> Speaker swivels 180° vertically orhorizontally depending onorientation of mounting bracket
> 30" (762mm) numbered wireleads
> Supplied with factory sealed 1/2"(13mm) threaded fitting for quickinstallation
> Heavy duty zinc cast construction
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-27
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5533MD-AW 20-31 VDC 0.061 0.400
Horn pivots one way 180°
11 1/4"(286mm)
11 1/4"(286mm)
18 3/8"(467mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-42ELECTRONIC SIGNALS
Adaptatone®
Remote Speaker/Amp
The Edwards 5545M Hazardous Location Adaptatone Remote
Speaker/Amplifier has been designed for high decibel system opera-
tion when connected to the 5540M Central Tone Generator or 5541M
System Master Panel. See Adaptatone Tone Generator page 4-28.
Each Speaker/Amplifier operates directly from local power sources,
making it possible in a single system to connect the remote
Speaker/Amplifiers to local power sources of different voltages. The
unit mounts on any surface using three bolts. See Adaptatone Sig-
naling System Installation, pages 4-56.
Typical applications include signaling use in mining, granaries, flour
mills, tankers, refineries, laboratories, spray booths, and other haz-
ardous locations.
5545M SeriesFEATURES
> Corrosion resistant electrostaticheat flowed epoxy finish
> Individual volume control
AGENCY APPROVALS
> UL 464 and UL 1203 Listed
> UL Listed for Class I, Division 1and 2, Groups B, C, and Dhazardous locations
SPECIFICATIONS
> Speaker swivels 180° vertically orhorizontally depending onorientation of mounting bracket
> 30" (762mm) numbered wireleads
> Supplied with factory sealed 1/2"(13mm) threaded fitting for quickinstallation
> Heavy duty zinc cast construction
Explosionproof
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-43
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5545M-AQ 24V DC 0.061 0.47024V AC 50/60 Hz 0.250 1.320
5545M-Y6 120V AC 50/60 Hz 0.088 0.260240V AC 50/60 Hz 0.091 0.190
125V DC 0.031 0.130250V DC 0.091 0.070
Horn pivots one way 180°
11 1/4"(286mm)
11 1/4"(286mm)
18 3/8"(467mm)
D-04
ELECTRIC CHIMES
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com9-4
© Copyright 2004 Edwards
Edwards Builders Chime Kits consist of an Edwards two entrance
chime, a16V transformer, and two pushbuttons (option of either illu-
minated or non-illuminated).
For use in new or existing single or two entrance homes, apart-
ments, condominiums, and offices.
Builders Chime Kits
C212 SeriesFEATURES
> Complete installation kit
> Two entrance models
> Illuminated pushbuttons available
> Available in white or beige
Complete Installation Kit
D-0
4
ELECTRIC CHIMES
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
9-5© Copyright 2004 Edwards
2"(51mm)
3°(4 sides)
4 3/8"(111mm)
7 1/4"(184mm)
Slots top & bottom
TexturedFront
Number ofCat. No. Color Entrances Volts AC Amps V A Contents of Kit
C212 Beige Two 16V .625 10 (1) Beige Chime, (1) 16V Transformer, (2) Push Buttons
C212-W White Two 16V .625 10 (1) White Chime, (1) 16V Transformer, (2) Push Buttons
C212-2L Beige Two 16V .625 10 (1) Beige Chime, (1) 16V Transformer, (2) Lighted Push Buttons
C212W-2L White Two 16V .625 10 (1) White Chime, (1) 16V Transformer, (2) Lighted Push Buttons
D-04
www.edwards-signals.com 2 0 3 . 6 9 9 . 3 3 0 0
Schedule signals for events asmundane as lunch or deliveremergency voice communications –all without leaving your desk – with the Millennium Event Driver Interface(MEDI™). This windows-based softwarepackage provides command and
control of remote signaling devicesthroughout your facility. With a fewsimple clicks, MEDI can automaticallysignal work start and stop times,break times, or any other timedevent. You can also manually command MEDI to initiate tones,
wav files, or real-time voice. Anytime.It integrates with either conventionalor RS485 signaling components.
Put the facilities communicationshub where it belongs – in youroffice. When you Signal Responsibly™
with Edwards.
Signal ResponsiblyTMfrom your desktop or laptop.
EDW-1128 MEDI Ad (no bar) - Trim 8.5 X 11, Bleed 8.75 x 11.25 Pub: A-D Today
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
The Cat. No. 725 is a low cost, fully insulated, non adjustable
buzzer. The Cat. No. 730 is a low cost, non adjustable combination
bell and buzzer with grounded frame. May be operated using AC
power supplied by a 590 transformer or from DC power. See Trans-
former Catalog Page 11-2.
Universal economy buzzer or bell and buzzer combination widely
used in homes, apartment houses, plants, and OEMs.
Dixie BuzzerTM &Dixie BuzabelTM
725 & 730 Series
Low voltage
FEATURES
> Low voltage
> Attractive snap on covers
> Fully enclosed
> Satin aluminum finish
> Cat. No. 725 - enclosed bindingposts
> Cat. No. 730 - enclosed terminals
A 1"(25mm)
B
DC Coil dB atCat. No. Volts Amps VA Res. (Ohms) 1m / 10 ft A B
725 6V AC 1.20A 7.2 1.0 88 / 82 1 3/4" 2 3/4"(45mm) (69mm)
730 6V AC 0.7A 4.2 3 88 / 82 3" 5 1/4"3-6V DC 1.4A 8 3 (76mm) (133mm)
6-8V AC 60 Hz 1.4A 8 3
5-36
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
Edwards Lumatone signals are designed to demand attention in
quiet and moderate noise areas. The signal’s output can be varied
by controlling the applied voltage. The signal’s low power consump-
tion makes them suitable for battery operated equipment and allows
them to be turned on and off by integrated circuits, SCRs and tran-
sistors.
Simply unscrew front housing and insert threaded portion through a
1 5/32" (29mm) panel hole. Screw front housing back on. Signal can
accommodate panel thickness up to 3/16" (5mm).
Used for security systems, computers, appliances and industrial,
process control, communication and restaurant equipment.
Lumatone®
Electronic Signals
E100 Series
Audio or Audio/Visual
1.44"(37mm)
1.75"*(44mm)
1.31"(33mm)
1.64"(42mm)
*Does not includepanel thickness
Max. Operating Pulsating LEDCat No. Description Voltage Current VA Rate IntensityE102A Steady audio 12V DC 10 mA 0.12 N/A N/A
24V DC 18 mA 0.44 N/AE103A Pulsating audio 12V DC 10 mA 0.12 90 N/A
24V DC 18 mA 0.44 60E104A Steady visual/audio 12V DC 16 mA 0.20 N/A 1.3 mcd
24V DC 30 mA 0.75 N/AE105AE Pulsating visual/audio 12V DC 16 mA 0.20 90 1.3 mcd
24V DC 30 mA 0.75 60
FEATURES
> Low cost and size
> Solid state, long life
> High impact polystyrene case
> Pulsating audio or audio/visualmodels available
> Terminal connections
SPECIFICATIONS
> Operating temperature range:-32° to 131°F (-0 to 55°C)
> Frequency: 2.8 kHz
6 8 10 12 14 16 18 20 22 24
DECIBELS VS. VOLTAGE FOR LUMATONE AUDIO SIGNALSTypical at Normal Temperature
100
90
80
70
60
Volts DC
dB a
t 1
foot
5-38
D-0
4
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-14ELECTRONIC SIGNALS
Adaptatone® MillenniumMultiple Tone Signal
The Edwards 5530MD-24AW Adaptatone Millennium is a heavy-
duty industrial, tone-selectable, signaling device intended primarily
for use in fire alarm systems and other applications requiring electri-
cal supervision of signaling circuit field wiring. It uses a micropro-
cessor circuit to create 27 distinctive tones A single tone may be
selected by setting a miniature dip switch within the unit. For a
complete listing of all 27 tones, see page 4-55. The Adaptatone Mil-
lennium can be activated from field-wired, normally open contacts,
or a 24VDC external voltage source such as an output of a PLC or
Fire/Security panel. Normally open contacts can be obtained from
the Cat. No. 5538-4 and/or Cat. No. 5538-4R Adaptatone Signal Ac-
tuators. See page 4-49.
1/2" (13mm) conduit or surface mounting. See Adaptatone Signal-
ing Installation, pages 4-56.
The signal may also be used for unsupervised signaling applica-
tions. Typical applications include fire alarm emergency warning
systems, plant evacuation and security intrusion alarms, process
monitoring, shift start-and-dismissal horns, and paging signals.
FEATURES
> 27 tone capability - No additionaltone modules needed
> Output up to 110 dB
> Suitable for Division 2 Locations
> Diode polarized for supervisorycircuits
> Captive Components
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and UL 1604 Listed forindoor and outdoor applications
> CSFM
> CE Marked
> ULC S525
> UL Listed for use in Class I,Division 2, Groups A, B, C & D;Class II, Division 2, Groups F &G; and Class III HazardousLocation applications
> TUV Rheinland Certified
SPECIFICATIONS
> Speaker can be rotated andlocked in any horizontal direction
5530MD-24AW
Diode Polarized for Fire AlarmCommunication, Single Output
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-15
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5530MD-24AW 20-31V DC 0.10 0.80
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
8 47/64"(222mm)
8"(203mm)
13 3/4"(349mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
8"(203mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-16OUTDOOR WARNING SYSTEMS
Airchime® Air Horns
C Series
These air horns are for general signaling services. They generate
sound by means of a vibrating diaphragm that modulates the flow of
compressed air into a resonating projector. All horn shapes are
mathematically calculated to amplify sound while closely retaining
its fundamental frequency and natural harmonics. All horn frequen-
cies are designed to give balance to any combination of horn tones.
These horns can be used in indoor/outdoor applications, ideal for
hazardous location use, individual equipment and plant warnings.
Volume is adjustable by regulating air pressure.
Designed for mounting on air supply piping, supplying between 50
and 150 PSIG (3.5 and 10.5 kg/sq cm). May be bracket mounted
using the AC30106 post bracket.
Typical applications include: emergency signaling applications such
as mines, refineries and industrial facilities. They can also be used
for signaling activities such as shift start/stop, blast warning and
equipment stop/starts.
Cat. No. C-12
Cat. No.CA-4
Cat. No. C-1E
FEATURES
> Corrosion resistant cast bronzebody
> Stainless steel diaphragm
> Machined or spun bell
> Effective range - 1/4 mile (.4 km)*
> Single or dual tone frequency
Cat. No. CA
Air Consumption Air PressureFreq. dB(c) dB(c) Cu. Ft. /Sec. PSI Inlet Net
Cat. No. Description (Hz) at 10 ft. at 100 ft. (Liters/Sec.) (Kg/Sq Cm) NPT Length Weight
CA Single tone 745 124 104 .25 3/8" 4 3/4" 3 lbmachined bell (7.1) (9.5mm) (120mm) (1.3 kg)
CA-4 Omni-directional 745 124 104 1 1/2" 11 1/4" 12 lb4 model CA horns (28.4) (13mm) (286mm) (5.2 kg)
CB Single tone 523 117 97 .25 50 - 150 3/8" 7 3/8" 2 3/4 lbSpun bell (7.1) (5.3 - 10.5) (9.5mm) (187mm) (1.2 kg)
C-1E Single tone 246 117 97 .25 3/8" 15 3/4" 3 lbSpun bell (7.1) (9.5mm) (400mm) (1.3kg)
C-12 Dual tone 246/311 118 98 .50 3/8" 15 3/4" 8 lbSpun bell (14.2) (9.5mm) (400mm) (3.6 kg)
AC30106 Post bracket for Air Horn Cat. No's. CB, C-1E, C-12 and CA
* Subject to environmental and geographical conditions, these models have a typical effective range of 1/4 mile (.4 km) assuming an ambient background level of 60dB, a line pressure of 100 psi(7.03 kg/sq cm) and temperature of 60°F (15.6°C). Derated per FEMA guidelines @ 10 dB per distance doubled.D
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-18OUTDOOR WARNING SYSTEMS
Airchime® Air Horns
* Subject to environmental and geographical conditions, these models have a typical effective range of 3/4 mile (1.2 km) assuming an ambient background level of 60dB, aline pressure of 100 psi (7.03 kg/sq cm) and temperature of 60°F (15.6°C). Derated per FEMA guidelines @ 10 dB per distance doubled.
The K series is designed for general signaling services. They gen-
erate sound by means of a vibrating diaphragm that modulates the
flow of compressed air into a resonating projector. All horn shapes
are mathematically calculated to amplify sound while closely retain-
ing its fundamental frequency and natural harmonics.
These horns can be used for indoor/outdoor applications and are
ideal for hazardous location use. Volume is adjustable by regulating
air pressure.
Designed for mounting on air supply piping, supplying between 50
and 150 PSIG (3.5 and 10.5 kg/sq cm).
Typical applications include emergency signaling applications in
mines, refineries and industrial facilities. Ideal for individual equip-
ment and plant warnings.
Cat. No.K-1
Cat. No.K-12
K SeriesCat. No.K-25R25
FEATURES
> Die cast aluminum construction
> Adjust volume via air pressure
> Hermetically sealed diaphragm
> Effect. range - 3/4 mile (1.2 km)*
SPECIFICATIONS
> .5 - 2 cu ft /sec(14.2 - 5.6 liters/sec)
> Operating range - 50 to 150 PSIG(3.5 to 10.5 kg/sq cm)
Air ConsumptionFreq. dB(c) dB(c) Cu. Ft. /Sec. Inlet Net Weight
Cat. No. Description (Hz) at 10 ft. at 100 ft. (Liters/Sec.) NPT Length lbs. (kg)
K-1 Single tone, cast base, die cast alu- 311 134 114 .50 (14) 1/2" (13mm) 16 1/2" (419mm) 7 1/2 (3.4)minum body, 3 piece hermeticallysealed stainless steel diaphragm
K-2 Same as above 370 130 110 .50 (14) 1/2" (13mm) 12 7/8" (327mm) 6 1/2 (2.9)K-3 Same as above 470 133 113 .50 (14) 1/2" (13mm) 10 1/4" (260mm) 6 1/4 (2.8)K-5 Same as above 622 132 112 .50 (14) 1/2" (13mm) 7 1/2" (191mm) 5 (2.2)
K-12 Dual tone incorporating 311/370 134 114 1 (28) 1/2" (13mm) 16 1/2" (419mm) 14 1/2 (6.5)K1 & K2 with base
K-25 Dual tone incorporating 370/622 135 115 1 (28) 1/2" (13mm) 12 7/8" (327mm) 12 (5.4)K2 & K5 with base
K-12R12 Dual tone incorporating 311/370 135 115 2 (56) 3/4" (19mm) 16 1/2" (419mm) 24 1/2 (11.1) 2 K-12 Air Horns reversedfor 180° coverage with base
K-25R25 Dual tone incorporating 370/622 136 116 2 (56) 3/4" (19mm) 12 7/8" (327mm) 55 (24.9 )2 K-25 Air Horns reversed
for 180° coverage with base
Single or Dual Tone
D-0
4
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-40ELECTRONIC SIGNALS
Adaptatone® MillenniumRemote Speaker/Amp
The Edwards 5532MHV Adaptatone Millennium Remote Speaker/
Amplifier has been designed for high decibel system operation
when connected to the 5540M Central Tone Generator or 5541M
System Master Panel. See Adaptatone Tone Generator, page 4-28.
Each Speaker/Amplifier operates directly from local power sources,
making it possible in a single system to connect the remote
Speaker/Amplifiers to local power sources of different voltages. De-
signed for either 1/2" (13mm) conduit or surface mounting.
The 5532MHV-485Y6 is designed to be connected to RS485 net-
works, allowing full signaling communication control.
Adaptatone Signaling Systems are designed for industrial applica-
tions calling for high decibel output and microprocessor reliability
combined with simultaneous signal delivery over all speakers in-
cluded in the system. Typical applications include: emergency
warning systems, plant evacuation alarms, security intrusion si-
rens, process monitoring, shift start-and-dismissal horns, and pag-
ing signals.
RS485 units are MEDI compatible. See page 4-10.
5532MHV Series
30 Watt, High Volume SystemSpeaker, RS485 Activation
FEATURES
> Output up to 113 dB at 10 ft
> Corrosion resistant electrostaticheat flowed epoxy finish
> Individual volume control
> Suitable for Division 2 Locations
> Captive Components
> RS485 models available
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> cUL 22.2 No. 205
> UL & cUL Listed for indoor andoutdoor applications for use inClass I, Division 2, Groups A, B,C & D; Class II, Division 2,Groups F & G; and Class IIIHazardous Locations
> TUV Rheinland Certified
> CE Marked, LV & EMC Directives(Y6 AC only and AQ models)
SPECIFICATIONS
> 24V DC battery backup terminalsprovided
> Speaker can be rotated andlocked in any horizontal direction
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-41
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5532MHV-AQ 24V DC 0.10 1.2224V AC 50/60 Hz 0.10 2.21
5532MHV-Y6 120V AC 50/60 Hz 0.10 0.48240V AC 50/60 Hz 0.10 0.28
125V DC 0.10 0.32250V DC 0.10 0.15
5532MHV-485Y6 120V AC 50/60 Hz 0.10 0.48240V AC 50/60 Hz 0.10 0.28
125V DC 0.10 0.32250V DC 0.10 0.15
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
11 1/2"(292mm)
9 3/4"(248mm)
15"(381mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
9 3/4"(248mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-44ELECTRONIC SIGNALS
Adaptatone® MillenniumLocal/System Signal
The Edwards 5536M Adaptatone Millennium accepts three electri-
cal inputs from the closing of three normally open contacts, or a
24VDC external voltage source such as an output of a PLC, and
delivers three tones from the 27 tones available. One of these in-
puts is a priority signal. The 5536M can also work within an
Adaptatone System, sounding the central tone or voice signal or its
own tone signals. The Adaptatone Millennium System has priority
over the locally initiated contacts. See Adaptatone Signaling Sys-
tem Installation, page 4-56.
Programming the signal for the tones selected is accomplished
through setting internal dipswitches. On-site volume control is also
available by adjusting the internal volume control.
The programmed tones on the 5536M operate on a pyramid-type
priority system in which a switch with a programmed tone takes pri-
ority over all switches that follow it. For more information on priority
tone operation and a complete listing of all 27 tones, see page 4-55.
Designed for either 1/2" (13mm) conduit or surface mounting. See
Adaptatone Signaling System Installation, pages 4-56.
The 5536M Adaptatone is designed for industrial applications call-
ing for high decibel output and microprocessor reliability combined
with simultaneous signal delivery over all speakers included in the
system. Typical applications include: emergency warning systems,
plant evacuation alarms, security intrusion sirens, process monitor-
ing, shift start-and-dismissal horns, and paging signals.
5536M Series
Three Outputs & Priority
FEATURES
> Output up to 110 dB at 10 ft
> 27 tone capability - No additionaltone modules needed
> PLC Compatible
> Suitable for Division 2 locations
> Corrosion resistant electrostaticheat flowed epoxy finish
> Individual volume control
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL & cUL Listed for indoor andoutdoor applications in Class I,Division 2, Groups A, B, C & D;Class II, Division 2, Groups F &G; and Class III HazardousLocation applications
> TUV Rheinland Certified
> CE Marked, LV & EMC Directives(24Y6 AC only & 24AQ models)
SPECIFICATIONS
> 24V DC battery backup terminals
> Speaker can be rotated andlocked in any horizontal direction
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-45
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5536M-24AQ 24V DC 24VDC 0.10 0.6424V AC 50/60 Hz 0.10 1.22
5536M-24N5 120V AC 50/60 Hz 24VDC 0.10 0.28
5536M-24Y6 125V DC 24VDC 0.10 0.15250V DC 0.10 0.77
120V AC 50/60 Hz 0.10 0.24240V AC 50/60 Hz 0.10 0.15
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)Operating Max. off state Continuous on Surge (inrush/duration)
Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5536M-24AQ 24V DC only 2 740 8/4
5536M-24N5 120V 50/60 hz 2 360 2.82/4
24VDC 5V DC to 24V DC 2 6 —Input Board (each input)
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
8 47/64"(222mm)
8"(203mm)
13 3/4"(349mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
8"(203mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-22ELECTRONIC SIGNALS
Adaptatone® MillenniumMultiple Tone Signal
The Edwards 5531MV Adaptatone Millennium Voice unit is a heavy-
duty industrial, tone-selectable, signaling device capable of produc-
ing volume-controlled, high-decibel tones and up to 20 seconds of
field recorded voice messages. The Adaptatone Millennium Voice
unit can be activated from field-wired, normally open contacts, or a
24VDC or 120VAC external voltage source such as an output of a
PLC. Normally open contacts can be obtained from the Cat. No.
5538-4 and/or Cat. No. 5538-4R Adaptatone Signal Actuators. See
page 4-49.
The unit uses a microprocessor circuit to create 27 distinctive
tones and store 20 seconds of field recorded voice messages. Mes-
sages and tones may be selected by setting miniature dip switches
within the unit. A total of four messages and tones programmed op-
erate on a pyramid-type priority system. For more information on
priority tone operation and a complete listing of all 27 tones, see
page 4-55.
The 5531MV is designed for either 1/2" (13mm) conduit or surface
mounting. See Adaptatone Signaling Installation, pages 4-56.
Designed for industrial applications including emergency warning,
plant evacuation and security alarms, process monitoring, shift noti-
fication horns, paging and process control.
PLC CompatibleVoice Capability5531MV Series
FEATURES
> Stand-alone, 27 tone capability -No additional tone modulesneeded
> Output up to 110 dB @ 10 ft
> PLC compatible
> 20 sec. of field recorded VoiceMessages
> Suitable for Division 2 Locations
> Captive Components
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL Listed for indoor and outdoorapplications in Class I, Division2, Groups A, B, C & D; Class II,Division 2, Groups F & G; andClass III Hazardous Locations
> cUL C22.2 No. 205 (24N5 model)
SPECIFICATIONS
> Built-in cascading priority system
> Speaker can be rotated andlocked in any horizontal direction
> 24V DC battery backup terminals
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-23
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5531MV-24N5 120V AC 50/60 Hz 24VDC 0.10 0.23
5531MV-120N5 120V AC 50/60 Hz 120VAC 0.10 0.23
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5531MV-24N5 120V 50/60 hz 2 360 2.82/4
5531MV-120N5 120V 50/60 hz 5 380 2.82/4
24VDC 5V DC to 24V DC 2 6 —Input Board (each input)
120VAC 120VAC 50/60 Hz 5 13 —Input Board (each input)
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
8 47/64"(222mm)
8"(203mm)
13 3/4"(349mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
8"(203mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-46ELECTRONIC SIGNALS
Adaptatone® MillenniumLocal/System Signal
The Edwards 5536MHV high output Adaptatone Millenium accepts
three electrical inputs from the closing of three normally open con-
tacts, or a 24VDC or 120VAC external voltage source such as an
output of a PLC, and delivers three tones from the 27 tones avail-
able. One of these tones is a priority signal. The 5536MHV can also
work within an Adaptatone System, sounding the central tone or
voice signal or its own tone signals. The Adaptatone System has
priority over the locally initiated contacts. See Adaptatone Signaling
System Installation, page 4-56.
Programming the signal for the tone or tones selected is accom-
plished through setting internal dipswitches. On-site volume control
is also available by adjusting the internal volume control.
The programmed tones on the 5536MHV operate on a pyramid-type
priority system in which a switch with a programmed tone takes pri-
ority over all switches that follow it. For more information on priority
tone operation and a complete listing of all 27 tones, see page 4-55.
Designed for either 1/2" (13mm) conduit or surface mounting.
The 5536MHV Adaptatone is designed for industrial applications
calling for high decibel output and microprocessor reliability com-
bined with simultaneous signal delivery over all speakers included
in the system. Typical applications include: emergency warning
systems, plant evacuation alarms, security intrusion sirens, pro-
cess monitoring, shift start-and-dismissal horns, and paging sig-
nals.
5536MHV Series
30 Watt, High VolumeThree Outputs & Priority
FEATURES
> 30 Watt Output to 113 dB @ 10 ft
> 27 tone capability - No additionaltone modules needed
> PLC compatible
> Suitable for Division 2 locations
> Corrosion resistant electrostaticheat flowed epoxy finish
> Individual volume control
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL & cUL Listed for indoor andoutdoor applications in Class I,Division 2, Groups A, B, C & D;Class II, Division 2, Groups F &G; and Class III HazardousLocation applications
> cUL C22.2 No. 205
> TUV Rheinland Certified
> CE Marked, LV & EMC Directives(Y6 AC only & AQ models)
SPECIFICATIONS
> 24V DC battery backup terminals
> Speaker can be rotated andlocked in any horizontal directionD
-04
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-47
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5536MHV-24AQ 24V DC 24VDC 0.10 1.1424V AC 50/60 Hz 0.10 1.73
5536MHV-24Y6 125V DC 24VDC 0.03 0.34250V DC 0.02 0.17
120V AC 50/60 Hz 0.10 0.53240V AC 50/60 Hz 0.07 0.30
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5536MHV-24AQ 24V DC only 2 1500 8/4
24VDC Input 5V DC to 24V DC 2 6 —Board Circuit (each input)
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
11 1/2"(292mm)
9 3/4"(248mm)
15"(381mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
9 3/4"(248mm)
2 1/2"(64mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-32ELECTRONIC SIGNALS
Adaptatone® MillenniumCentral Tone Generator
The Edwards 5540MP Millennium Central Tone Generator, when
used with the 5542RPU Remote Paging Unit, is designed for appli-
cations where voice paging and other audio output are desired. The
paging/voice signal is inputed into the Remote Paging Unit via ei-
ther an audio pair or the 5542MIC series microphone.
The Millennium Central Tone Generator produces the 27 standard
Adaptatone sounds. The tone generator assures a synchronous sig-
naling sound from all remote speakers. Three tones may be pro-
grammed into the Tone Generator at any time. The tones may be
selected by setting miniature dip switches within the unit. The tones
operate on a pyramid-type priority system. The input from the Re-
mote Page Unit has priority over all three tones. The three signals
may be activated from field-wired, normally open contacts or a
24VDC external voltage source such as an output from a PLC. Nor-
mally open contacts can be obtained from the Cat. No. 5538-4 or
Cat. No. 5538-4R Adaptatone Signal Actuator. See page 4-49.
Adaptatone Signaling Systems are designed for industrial applica-
tions calling for high decibel output, voice paging, and microproces-
sor reliability combined with simultaneous signal delivery over all
speakers included in the system. Typical applications include: emer-
gency warning systems, plant evacuation alarms, security intrusion
sirens, process monitoring, shift start-and-dismissal horns, and
paging signals.
5540MP Series
Synchronized SystemPaging & Signaling
FEATURES
> Voice paging
> 27 tone capability - No additionaltone modules needed
> Suitable for Division 2 Locations
> Centralized programmable toneselection
> System-wide priority toneselection
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL Listed for indoor and outdoorapplications in Class I, Div. 2,Groups A, B, C & D; Class II, Div.2, Groups F & G; and Class IIIhazardous locations
> cUL C22.2 No. 205
SPECIFICATIONS
> 24V DC battery backup terminalsprovided
> Short Circuit protected
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-33
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5540MP-24Y6* 120V AC 50/60 Hz 24V DC 0.10 0.32240V AC 50/60 Hz 0.10 0.20
125V DC 0.10 0.21250V DC 0.02 0.10
* Must be connected to 5542RPU to operate
HazardousLocationSpeaker/AmplifierCat. Nos. 5545B
Speaker/AmplifierCat. No. 5532MHV
Speaker/AmplifierCat. No. 5532M Local/System Signal
Cat. No. 5536M3 Local Tones
Central ToneGenerator with pagingCat. No. 5540MP
ReentrantSpeakerCat. No. 5547
Cone SpeakerCat. No. 5551B
Remote AmplifierCat. No. 5535
Remote Signal ActuatorCat. No. 5538-4
for local inputs 2, 3, 4
4 wires5 wires
Cat. No. 5542RPU-M1V peak to peak audiosource or telephone systemaudio converted usingBogen Telephone AccessModule or equivalent
*Local Power 3 wires
Typical Adaptatone Paging System Configuration
Mounting flange4 holes (2 each side)
2 1/2"(64mm)
6"(152mm)
4"(102mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
3 1/2"(89mm)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-18ELECTRONIC SIGNALS
Adaptatone® MillenniumMultiple Tone Signal
The Edwards 5531M Series Adaptatone Millennium is a heavy-duty
industrial, tone-selectable, signaling device capable of producing
volume-controlled, high-decibel tones. four tones can be activated
from field-wired, normally open contacts, or a 24VDC or 120VAC
external voltage source such as the output of a PLC. Normally open
contacts can be obtained from the Cat. No. 5538-4 and/or Cat. No.
5538-4R Adaptatone Signal Actuators. See page 4-49.
The unit uses a microprocessor circuit to create 27 distinctive
tones, by setting miniature dip switches within the unit. The pro-
grammed tones operate on a pyramid-type priority system. For
more information on priority tone operation and a complete listing of
all 27 tones, see page 4-55.
Designed for industrial applications. Typical applications include
emergency warning systems, plant evacuation and security alarms,
process monitoring, shift notification horns, and paging signals.
The 5531M is designed for either 1/2" (13mm) conduit or surface
mounting. See Adaptatone Signaling Installation, pages 4-56.
Four Outputs
5531M SeriesFEATURES
> 27 tone capability - No additionaltone modules needed
> Output up to 110 dB @ 10 ft
> PLC compatible
> Suitable for Division 2 Locations
> Captive Components
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604
> UL Listed for indoor and outdoorapplications in Class I, Division2, Groups A, B, C & D; Class II,Division 2, Groups F & G; andClass III Hazardous Locations
> cUL C22.2 No. 205 (24AQ, 24N5& 24Y6 models)
> CE Marked, LV & EMC Directives,(24Y6 AC only & 24AQ models)
> TUV Rheinland Certified
SPECIFICATIONS
> Built-in cascading priority system
> Speaker can be rotated andlocked in any horizontal direction
> 24V DC battery backup terminals
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-19
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5531M-24AQ 24V DC 24VDC 0.10 0.5724V AC 50/60 Hz 0.10 0.98
5531M-24N5 120V AC 50/60 Hz 24VDC 0.10 0.235531M-120N5 120VAC 0.10 0.23
5531M-24Y6 120V AC 50/60 Hz 24VDC 0.10 0.285531M-120Y6 240V AC 50/60 Hz 120VAC 0.08 0.15
125V DC 0.10 0.15250V DC 0.02 0.08
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5531M-24AQ 24V DC only 2 740 8/4
5531M-24N5 120V 50/60 hz 2 360 2.82/4
5531M-120N5 120V 50/60 hz 5 380 2.82/4
24VDC 5V DC to 24V DC 2 6 —Input Board (each input)
120VAC 120VAC 50/60 Hz 5 13 —Input Board (each input)
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
8 47/64"(222mm)
8"(203mm)
13 3/4"(349mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
8"(203mm)
2 1/2"(64mm)
D-04
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-48
Adaptatone® RemoteAmplifier and AudioSignal Converter
The Edwards 5535 Remote Amplifier has been designed to power
remote speakers in Adaptatone system operation. The amplifier
output is 70V line with a maximum of 15 watts.
The 5510M Audio Signal Converter allows signaling flexibility
through the integration of Adaptatone signals into installed paging
systems. The 5510M-25Y6 converts a 25V RMS input into a 10
VRMS output. The 5510M-70Y6 converts a 70V RMS input into a
10V RMS output.
All units are designed for either 1/2" (13mm) conduit or surface
mounting in industrial applications calling for high decibel output
and microprocessor reliability combined with simultaneous signal
delivery over all speakers included in the system. Typical applica-
tions include: emergency warning systems, plant evacuation
alarms, security intrusion sirens, process monitoring, shift start-
and-dismissal horns, and paging signals.
5535 & 5510M SeriesFEATURES
> 15 Watts
> Weatherproof
> Corrosion resistant electrostaticheat flowed epoxy finish
AGENCY APPROVALS
> UL 464 Listed
> NEMA Type 3R
> IP 44
SPECIFICATIONS
> Heavy duty zinc cast construction
> 24V DC battery backup terminalsprovided
Cat.No.5535
Cat.No.5510
Signal Off Signal OnCat. No. Volts Standby Current (Amps) Operating Current (Amps)5535-N5 120V AC 50/60 Hz 0.110 0.3105510M-25Y6 125V DC 0.10 0.155510M-70Y6 250V DC 0.10 0.77
120V AC 50/60 Hz 0.10 0.24240V AC 50/60 Hz 0.10 0.15
3 1/2"(89mm)
6 3/8"(162mm)
(2) Mounting holesfor wall mounting
1/2" (13mm)conduitmounting
6 3/8"(162mm) 3 1/2"
(89mm)
Mounting flange4 holes (2 each side)
1/2" (13mm)conduit mounting
6"(152mm)
2 1/2"(64mm)
6"(152)
2"(51mm)
8"(203mm)
Cat. No. 5535 Remote Amplifier Cat. No. 5510 Audio Signal Converter
D-0
4
© Copyright 2004 Edwards
90 F ie ldstone Cour t ||||| Cheshi re , CT 06410Ph : 203 .699 .3300 ||||| Fx : 203 .699 .3108
www.edwards-s ignals.com
BELLS & BUZZERS
The Edwards B-8140-M & B-8141-M Mineguard series are quality,
heavy duty buzzers suitable for use on permissible mining equip-
ment. They are available in AC and DC voltages. The sound is pro-
duced by the hammer action of a vibrating armature against the cast
aluminum cover. A one piece cast aluminum cover provides an effec-
tive explosion-proof seal; the seal is secured by a hex screw in the
cover. For power connections, the unit features an installed 33"
(84mm) power cord and conduit hose constructed of flame retardant
neoprene. The buzzer is provided with two mounting lugs for wall
mounting.
For use in all mining applications. Designed to withstand the con-
stant vibration associated with mining equipment such as loaders,
carriers, and conveyors.
MineguardTM
Mine Buzzers
B-8140-M & B-8141-M
MSHA Certified
FEATURES
> Heavy duty cast aluminumhousing and cover
> Corrosion resistant heat flowedpowder epoxy finish
AGENCY APPROVALS
> MSHA Certified No. X/P-3116-1
> Conforms with MSHA 30 CFR,Part 18 for methane and airmixtures
2 holes3/8" (10mm) dia.
5 1/2"(140mm)
6 3/8"(162mm)
Tap 1/2" (13mm) IP
5 3/8"(137mm)
3"(76mm)
DC Coil dB atCat No. Volts Amps VA Res (ohms) 1m / 10 ft.
B-8140-M-G5 24V AC 60 Hz 1.1 19.2 5.0B-8140-M-N5 120V AC 60 Hz 0.2 24 146 95 / 89B-8140-M-R5 240V AC 60 Hz 0.1 24 740
B-8141-M-G1 24V DC 0.8 19.2 21.5 95 / 89B-8141-M-S1 250V DC 0.1 25 600
5-31D
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-4OUTDOOR WARNING SYSTEMS
Lots of power in a small package. Great versatility - whether you
are supplying a large industry, small community, or filling “dead
spots,” the 107 dB rated omni-directional EWS-V1 Series is the an-
swer. The non-corrosive, cast aluminum fan is powered by a 5 Hp
motor in your choice of single or three phase power, and produces a
port tone frequency of 460 cycles per second.
All exposed siren components are made of zinc plated, steel con-
struction, which are “powder coated” for the most durable finish
available. The fan and housing are both made of non-corrosive cast
aluminum.
Maximum diameter of the Cat. No. EWS-V1 Series is 34" (86.4 cm),
maximum height is 34" (86.4 cm), and the maximum dimensions of
mounting base are 19" (48.3 cm) square. Shipping weight of the si-
ren alone is 250 lbs (113.4 kg).
Omni-DirectionalEdwards Warning Siren
EWS-V1 SeriesFEATURES
> 107 dB @ 100 ft. (30.5 m)
> Omni-directional
> Continuous duty motor
> Skirted horn design
> Powder coated exterior
SPECIFICATIONS
> Three phase motor:- 5 HP 208/230/460 V 60 Hz.- Starting amps: 66- Running amps: 12
> Single phase motor:- 5 HP 230 V 60 Hz.- Starting amps: 127- Running amps: 23
> Port tone frequency: 460 cps
> Weight: 250 lbs. (113.4 kg)
> Max. diameter: 34" (86.4 cm)
> Max. height: 34" (86.4 kg)
> Max. mounting base: 19" (48.3cm) sq.
> Estimated sound circle:3200 ft. (975.4 m) continuous
107 dB, Skirted Horn Design
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V1-3 Outdoor warning siren - three phase motorEWS-V1 Outdoor warning siren - single phase motor
EWS-MS-V1-3 Remote magnetic motor starter - 3 phaseEWS-MS-V1-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V1 Remote magnetic motor starter - 1 phaseEWS-MS-V1-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 Single Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.
D-0
4
OUTDOOR WARNING SYSTEMS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
8-5
See page 8-13 for additional accessory information.
Edwards EWS-V2 Series combine large siren functions with cost
effectiveness making it ideal for small towns or volunteer fire de-
partments. Utilizing the same effective design and construction as
the EWS-V1, the EWS-V2 Series uses projectors to distribute and
organize sound. Rated at 109 dB, the EWS-V2 is an omni-direc-
tional siren that produces continuous 360° coverage.
The EWS-V2 Series is available in either single or three phase
power. It is a single tone siren, producing 460 cycles per second. All
exposed siren components are of zinc plated steel construction,
which are “powder coated” for the most durable finish available. The
fan and housing are made of non-corrosive cast aluminum.
Maximum diameter of the Model EWS-V1 Series is 34" (86.4 cm),
maximum height is 34" (86.4 cm), and the maximum dimensions of
mounting base are 19" (48.3 cm) square. Shipping weight of the si-
ren alone is 250 lbs (113.4 kg).
Omni-DirectionalEdwards Warning Siren
FEATURES
> 109 dB @ 100 ft. (30.5 m)
> Omni-directional
> Continuous duty motor
> 8 horn, equal length, single row
> Powder coated exterior
SPECIFICATIONS
> Three phase motor:- 5 HP 208/230/460 V 60 Hz.- Starting amps: 66- Running amps: 12
> Single phase motor:- 5 HP 230 V 60 Hz.- Starting amps: 127- Running amps: 23
> Port tone frequency: 460 cps
> Weight: 250 lbs. (113.4 kg)
> Max. diameter: 34" (86.4 cm)
> Max. height: 34" (86.4 cm)
> Max. mounting base: 19" (48.3cm) sq.
> Estimated sound circle: 4,000 ft.(1,219.2 m) continuous
EWS-V2 Series
109 dB, 8 Horn, EqualLength, Single Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V2-3 Outdoor warning siren - three phase motorEWS-V2 Outdoor warning siren - single phase motor
EWS-MS-V1-3 Remote magnetic motor starter - 3 phaseEWS-MS-V1-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V1 Remote magnetic motor starter - 1 phaseEWS-MS-V1-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish D
-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-6OUTDOOR WARNING SYSTEMS
Employing carefully designed horns to project sound over long dis-
tances, the EWS-V3 Series is Edwards newest model. The Cat. No.
EWS-V3 is rated at 112 dB and like most of Edwards outdoor warn-
ing sirens, is Omni-Directional. The EWS-V10 is a battery powered
version of the EWS-V3. The EWS-V10 includes a motor starter,
charging system and battery box.
The EWS-V3 is available in single phase or three phase and is a
single tone siren, producing 460 cycles per second, for optimal
sound penetration. All exposed siren components are of metal con-
struction, which are “powder coated” for the most durable finish
available. The fan and housing are made of non-corrosive cast alu-
minum. Maximum diameter of the EWS-V3 and EWS-V10 is 56"
(142.2 cm), maximum height is 41" (104.1 cm), and the maximum
mounting base dimension is 19" (48.3 cm) square. Shipping weight
of the siren is 350 lbs (158.8 kg).
Omni-DirectionalEdwards Warning Siren
EWS-V3 & EWS-V10 SeriesFEATURES
> AC model 112 dB @ 100 ft.(30.5m)DC model 118 dB @ 100 ft.(30.5m)
> Continuous duty motor
> 8 horn, equal length, single row
> Powder coated exterior
SPECIFICATIONS
> Three phase motor (EWS-V3):- 7.5 HP 208/230/460 V 60 Hz.- Starting amps: 105- Running amps: 19
> Single phase motor (EWS-V3):- 7.5 HP 230 V 60 Hz.- Starting amps: 204- Running amps: 37
> Port tone frequency: 460 cps
> Weight: 350 lbs. (158.8 kg)
> Max. diameter: 56" (142.2 cm)
> Max. height: 41" (104.1 cm)
> Max. mounting base: 19" (48.3cm) sq.
> Estimated sound circle:5,000 ft. (1524 m) continuous(AC Model)
> Estimated sound circle:7,000 ft. (2133.6 m) continuous(DC Model)
112 & 118 dB, 8 Horn, EqualLength, Single Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V3-3 Outdoor warning siren - three phase motorEWS-V3 Outdoor warning siren - single phase motorEWS-V10 Outdoor warning siren - Battery Powered
EWS-MS-V3-3 Remote magnetic motor starter - 3 phaseEWS-MS-V3-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V3 Remote magnetic motor starter - 1 phaseEWS-MS-V3-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.D-0
4
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-12OUTDOOR WARNING SYSTEMS
Featuring the industry’s largest drive motor, this 8 HP, battery pow-
ered rotating siren delivers all the features one expects from a pre-
mium warning device.
Utilizing a 460 Hz tone, the EWS-11's low pitch is designed to pen-
etrate structures and obstacles, making the warning area more
complete. The EWS-11 features the same bullet-proof design and
construction as other Edwards sirens. The EWS-11 uses top of the
line, maintenance free rotating mechanisims and hand rolled, cus-
tom formed projectors.
All exposed siren components are of heavy gauge aluminum alloy
and electro-plated, galvanized steel construction, which are "powder
coated" for the most durable finish available.
The entire mass of the siren is centered over the pole so no stabi-
lizing wires are required. Total shipping weight of the EWS-11 is 385
lbs. (174.6 kg).
RotatingEdwards Warning Siren
EWS-11 SeriesFEATURES
> 127 dB @ 100 ft. (30.5 m)
> Maintenance free siren & rotatingmechanism
> Self-contained electricalconnections (battery not included)
> Powder coated exterior
SPECIFICATIONS
> 8 HP motor
> Port tone freq.: 460 & 920 cps
> Weight: 385 lbs. (174.6 kg)
> Recommended batteries:
- Group 27 sealed lead acidmaintenance free (minimum)
- GelCel or AGM Optima Blue TopDeep Cycle Marine
127 dB
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-11 Outdoor warning siren
EWS-H-1 Siren heater w/ thermostat
EWS-CDP-3 Three function siren control centerEWS-CDP-1 Two function siren control centerEWS-T-1 One function siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.
D-0
4
OUTDOOR WARNING SYSTEMS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
8-7
Edwards most popular mid-sized siren is a proven performer.
Staged horn projectors help organize sound for even distribution
over a large radius. Rated at 115 dB, the EWS-V4 Series is an
omni-directional siren which produces continuous 360° coverage,
making it a superior alternative to a directional beam siren.
The perfect siren for small communities, the EWS-V4 is available in
either single or three phase power and is a single tone siren, pro-
ducing 460 cycles per second. All exposed siren components are of
metal construction, which are “powder coated” for the most durable
finish available. The fan and housing are made of non-corrosive
cast aluminum.
Maximum diameter is 78" (198.1 cm), maximum height is 56"
(142.2 cm), and the maximum mounting base dimension is 19"
(48.3 cm) square. Shipping weight of the siren alone is 325 lbs
(147.4 kg).
Omni-DirectionalEdwards Warning Siren
FEATURES
> 115 dB @ 100 ft. (30.5 m)
> Omni-Directional
> Continuous duty motor
> 8 horn, staggered length,single row
> Powder coated exterior
SPECIFICATIONS
> Three phase motor:- 10 HP 208/230/460 V 60 Hz.- Starting amps: 132- Running amps: 24
> Single phase motor:- 10 HP 230 V 60 Hz.- Starting amps: 258- Running amps: 47
> Port tone frequency: 460 cps
> Weight: 325 lbs (147.4 kg).
> Max. diameter: 78" (198.1 cm)
> Max. height: 56" (142.2 cm)
> Max. mounting base: 19" (48.3cm) sq.
> Estimated sound circle:6,000 ft. (1828.8 m) continuous
EWS-V4 Series
115 dB, 8 Horn, StaggeredLength, Single Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V4-3 Outdoor warning siren - three phase motorEWS-V4 Outdoor warning siren - single phase motor
EWS-MS-V4-3 Remote magnetic motor starter - 3 phaseEWS-MS-V4-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V4 Remote magnetic motor starter - 1 phaseEWS-MS-V4-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-8OUTDOOR WARNING SYSTEMS
Our most affordable dual tone siren, the EWS-V5 Series is de-
signed to excel in almost any application. Its staged horn projectors
provide a large, even coverage area. Rated at 122 dB, the Model
EWS-V5 is an omni-directional siren which produces continuous
360° coverage, a clear advantage over rotating sirens.
The EWS-V5 is available in either single or three phase power. It is
a dual tone siren, employing two rotors with different numbers of
ports to produce a greater range of frequency. One rotor produces
460 cycles per second, and the other produces 920.
All exposed siren components are of zinc plated, steel construc-
tion, which are “powder coated” for the most durable finish available.
The fan and housing are made of non-corrosive cast aluminum.
Maximum diameter of the siren is 78" (198.1 cm), maximum height
is 65" (165.1 cm), and the maximum mounting base is 19" (48.3
cm) square. Shipping weight of the siren alone is 600 lbs (272.2 kg).
Omni-DirectionalEdwards Warning Siren
EWS-V5 SeriesFEATURES
> 120 dB @ 100 ft. (30.5 m)
> Omni-Directional
> Continuous duty motor
> 8 horn, staggered length,dual row
> Powder coated exterior
SPECIFICATIONS
> Three phase motor:- 10 HP 208/230/460 V 60 Hz.- Starting amps: 132- Running amps: 24
> Single phase motor:- (2) 7.5 HP 230 V 60 Hz. motors- Starting amps: 400- Running amps: 74* NOTE: Uses two starters
> Port tone freq.: 460 & 920 cps
> Weight: 600 lbs. (272.2 kg)
> Max. diameter: 78" (198.1 cm)
> Max. height: 66" (167.6 cm)
> Max. mounting base: 19" (48.3cm) sq.
> Estimated sound circle:8,000 ft. (2438.4 m) continuous
120 dB, 8 Horn, StaggeredLength, Dual Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V5-3 Outdoor warning siren - three phase motorEWS-V5 Outdoor warning siren - single phase motor
EWS-MS-V4-3 Remote magnetic motor starter - 3 phaseEWS-MS-V4-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V4 Remote magnetic motor starter - 1 phaseEWS-MS-V4-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.D-0
4
OUTDOOR WARNING SYSTEMS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
8-9
Designed for medium or small, growing communities this siren is a
true workhorse. It is also our most popular dual tone siren. Rated at
122 dB, the Cat. No. EWS-V6 is an omni-directional siren which pro-
duces continuous 360° coverage, making it a superior alternative to
a rotating siren. The Cat. No. EWS-V9 is a battery powered version
of the EWS-V6. The EWS-V9 includes a motor starter, charging
system and battery box.
The EWS-V6 is available in either single or three phase power. Both
the EWS-V6 and EWS-V9 are dual tone sirens, employing two ro-
tors with different numbers of ports to produce a greater range of
frequency. One rotor produces 460 cycles per second, and the other
produces 920 cycles per second. All exposed siren components are
of metal construction, which are “powder coated” for the most du-
rable finish available. The fan and housing are made of non-corro-
sive cast aluminum.
Omni-DirectionalEdwards Warning Siren
FEATURES
> AC model 122 dB @ 100 ft.(30.5 m)DC model 125 dB @ 100 ft.(30.5 m)
> Omni-Directional> Continuous duty motor> 8 horn, equal length, dual rowSPECIFICATIONS
> Three phase motor:- 15 HP 208/230/460 V 60 Hz.- Starting amps: 198- Running amps: 36
> Single phase motor:- (2) 7.5 HP 230V 60 Hz. motors- Starting amps: 360- Running amps: 72* NOTE: Uses two starters
> Port tone frequency: 460 cps> Weight: 750 lbs.> Max. diameter: 78" (198.1 cm)> Max. height: 65" (165.1 cm)> Max. mounting base: 19" (48.3
cm) sq.> Estimated sound circle:
9,400 ft. (2865.1 m) continuous(AC model)11,000 ft. continuous (3352.8 m)(DC model)
EWS-V6 & EWS-V9 Series
122 & 125 dB, 8 Horn, EqualLength, Dual Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V6-3 Outdoor warning siren - three phase motorEWS-V6 Outdoor warning siren - single phase motorEWS-V9 Outdoor warning siren - DC motor
EWS-MS-V6-3 Remote magnetic motor starter - 3 phaseEWS-MS-V6-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V6 Remote magnetic motor starter - 1 phaseEWS-MS-V6-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com8-10OUTDOOR WARNING SYSTEMS
The Edwards EWS-V7 Series is large enough to tackle almost any
application. Taking advantage of a continuous duty industrial motor
and rated at 124 dB, the EWS-V7 is an omni-directional siren which
produces continuous 360° coverage, making it a superior alternative
to a directional beam type siren.
The EWS-V7 is available in either single or three phase power, and
is a dual tone siren, employing two rotors with different numbers of
ports to produce a greater range of frequency. One rotor produces
460 cycles per second, and the other produces 920 cycles per sec-
ond. All exposed siren components are of metal construction, which
are “powder coated” for the most durable finish available. The fan
and housing are made of non-corrosive cast aluminum. Maximum
diameter is 78" (198.1 cm), maximum height is 56" (142.2 cm), and
the maximum mounting base dimension is 19" (48.3 cm) square.
Shipping weight of the siren alone is 750 lbs (340.2 kg).
Omni-DirectionalEdwards Warning Siren
EWS-V7 SeriesFEATURES
> 124 dB @ 100 ft.m (30.5 m)
> Omni-Directional
> Continuous duty motor
> 8 horn, staggered length,dual row
> Powder coated exterior
SPECIFICATIONS
> Three phase motor:- 20 HP 208/230/460 V 60 Hz.- Starting amps: 258- Running amps: 47
> Single phase motor:- (2) 10 HP 230 V 60 Hz. motors- Starting amps: 510- Running amps: 94* NOTE: Uses two starters
> Port tone freq.: 460 & 920 cps
> Weight: 750 lbs. (340.2 kg)
> Max. diameter: 78" (198.1 cm)
> Max. height: 56" (142.2 cm)
> Max. mounting base: 19" (48.3cm) sq.
> Estimated sound circle:10,500 ft. (3200.4 m) continuous
124 dB, 8 Horn, StaggeredLength, Dual Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V7-3 Outdoor warning siren - three phase motorEWS-V7 Outdoor warning siren - single phase motor
EWS-MS-V7-3 Remote magnetic motor starter - 3 phaseEWS-MS-V7-3-W Remote magnetic motor starter - 3 phase, weatherproofEWS-MS-V7 Remote magnetic motor starter - 1 phaseEWS-MS-V7-W Remote magnetic motor starter - 1 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.D-0
4
OUTDOOR WARNING SYSTEMS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
8-11
The largest omni-directional siren in existence. Taking advantage of
a continuous duty, industrial motor and rated at 127 dB, the EWS-
V8-3 produces continuous 360° coverage, making it a superior alter-
native to directional beam type siren.
The EWS-V8-3 is available in three phase power only, and is a dual
tone siren, employing two rotors with different numbers of ports to
produce a greater range of frequency. One rotor produces 600
cycles per second, and the other produces 850 cycles per second.
All exposed siren components are of galvanized steel construction,
which are powder coated for the most durable finish available. The
fan and housing are made of non-corrosive cast aluminum. Maxi-
mum diameter of the siren is 78" (198.1 cm), maximum height is
67" (170.2 cm), and the maximum mounting base size is 24" (61
cm) square. Shipping weight of the siren is 1,200 lbs. (544.3 kg).
Omni-DirectionalEdwards Warning Siren
FEATURES
> 127 dB @ 100 ft. (30.5 m)
> Omni-directional
> Continuous duty motor
> 5 horn, equal length, dual row
> Powder coated exterior
SPECIFICATIONS
> Three phase motor:- 40 HP 208/230/460 V 60 Hz.- Starting amps: 500- Running amps: 96(using 230V power)
> Port tone freq.: 600 & 850 cps
> Weight: 1,200 lbs. (544.3 kg)
> Max. diameter: 78" (198.1 cm)
> Max. height: 67" (170.2 cm)
> Max. mounting base: 24" (61 cm)sq.
> Estimated sound circle:12,800 ft. (3901.4 m) continuous
EWS-V8-3
127 dB, 5 Horn, EqualLength, Dual Row
ORDERING INFORMATION & ACCESSORIESCat. No. DescriptionEWS-V8-3 Outdoor warning siren - three phase motor
EEWS-MS-V8-3-W Remote magnetic motor starter - 3 phase, weatherproof
EWS-CDP-3 Three Function Siren control centerEWS-CDP-1 Two Function Siren control centerEWS-T-1 One Function Siren control center
ENC-H Radio control - hand heldENC-D Radio control - desk mount
EWS-PMB Utility pole mounting bracket - powder coat finishEWS-PMB-SS Utility pole mounting bracket - stainless steel finish
See page 8-13 for additional accessory information.
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
6-27
Edwards®
Backup Alarms
The Edwards 8000 Series heavy duty backup alarms answers all
your needs with its convenient, compact size, rugged housing and
high decibel output. The 8001-EG die-cast alarm automatically
adjusts its output volume to 10 dB above ambient to compensate
for background noise. Range is 87 to 102 dB.
The 8002-EU has an ABS plastic housing and outputs 97 dB. Long
Term reliability is ensured as a result of its durable and versatile
construction. The alarm mounts in the rear of the vehicle with the
sound opening outward into the hazardous area.
Designed for indoor and outdoor application in a wide variety of
vehicles that operated in populated areas. This alarm is perfect for
heavy equipment such as forklifts, bulldozers, graders, tractors,
dump trucks, and waste disposal vehicles as well as emergency
and maintenance vehicles, buses, firetrucks, and general utility
vehicles. The Edwards 8000 Series Backup Alarm is an economical
life-safety device designed to prevent accidents.
8001-EG & 8002-EU
Heavy Duty
HORNS & SIRENS
FEATURES
> Solid state, epoxy-sealedelectronics
8001-EG> Auto Adjusts from 87 - 102dB
> Rugged Weatherproof Die-CastConstruction
8002-EU> 97dB Output
> Rugged Weatherproof ABSPlastic Housing
AGENCY APPROVALS
> Conforms to SAE J994 soundlevel Type C requirements
SPECIFICATIONS
8001-EG> 12 - 24VDC
> 87 - 102 dB rating based on "A"weighted scale (tolerance +/- 4dB)
8002-EU> 12 - 36VDC
> 97dB rating based on "A"weighted scale (tolerance +/- 4dB)
3"(76mm)
4.5"(114mm)
2"(51mm)
Cat. No.8001-EG
Cat. No.8002-EU
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-2ELECTRONIC SIGNALS
Duotronic®
Horns and Sirens
The 5520 and 5521 Series are low current, high performance, high
decibel signals which may be coded or used as a continuous alarm.
The 5520 Series is designed to function as either a horn or siren by
setting an internal, tamper proof switch. The signal's universal
Adaptaplate® mounts directly on walls, or on any single-gang open-
ing. Adaptaplate speeds installation by allowing the installer to con-
nect all field wiring to the plate and then finishing the installation by
snapping the horn onto the plate. It also mounts to 3 1/4" (83mm), 3
1/2" (89mm), 4" (102mm) octagon, 4" (102mm) square boxes, or
equivalent fittings. The signal may be weatherproofed using the
Edwards Cat. No. 349 back box (see page 5-10).
The 5521 operates as a horn only. It is intended for weatherproof
applications and must be mounted on the supplied Edwards Cat.
No. 349 backbox (see page 5-10) using the universal Adaptaplate®
(supplied).
The 5520 and 5521 Series are used for schools, factories, lumber
yards, and other industrial and commercial installations. The horn
signal is often used for timing, paging, and alarms. The siren signal
is particularly suitable for high noise areas and often used for alert-
ing an evacuation.
5520 & 5521 SeriesFEATURES
> 114 dB audible signal
> 5520 Series is weatherproofed byadding 349 back box
> 5521 Series is weatherproof assupplied
> Horn and siren or horn models
> Easy Adaptaplate installation
AGENCY APPROVALS
> UL 464 Listed
> FM Approved Audible NotificationAppliances Standard 3151-3152
SPECIFICATIONS
> Horn frequency - 1.1KHz
> Siren frequency - rises and fallsfrom 600 to 1300 Hz every 3seconds
> Speaker swivels 180° horizontallyand 90° vertically
High dB, Electronic Sound
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-3
*Uses separately mounted 598Y Transformer.
11"(279mm)
8 3/4"Dia.(222)
14"(356mm)
7" Dia.(178mm)
5 1/2"(140mm)
13 1/2"(343mm)
11"(279mm)
90°
Speaker can bepositioned anywherewithin 90° verticallyor 180° horizontally5520 Series may be weatherproofed using Cat. No. 349 back box (purchased separately.)
5521 is supplied with Cat. No. 349 weatherproof back box
dB atCat. No. Volts Amps VA 10 ft (3.05m)
5520-AS 12V AC 60 Hz 1.3 15.612V DC .7 8.4
5520-AQ 24V AC 60 Hz .85 20.4 11424V DC .35 8.4 (Horn)
5520-N5 120V AC 60 Hz .35 42 112
5520-P1 125V DC .1 12.5 (Siren)
5520-R5* 240V AC 60 Hz .1 24.0
5521-S1 250V DC .065 16.3 114 (Horn only)
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-8ELECTRONIC SIGNALS
The 5522D Horn and 5523D Siren are low current, high perfor-
mance, high decibel signals for hazardous locations. They are pri-
marily intended for use in hazardous location applications requiring
electrical supervision of signaling circuit field wiring. These signals
may also be used for unsupervised signaling applications.
They may be mounted on any surface using three bolts.
For use where a high decibel sound is required for alert or evacua-
tion in hazardous locations. Typical applications include signaling for
security, fire, power failure, and danger. Ideal for use in factories,
flour mills, refineries and paint shops.
Duotronic® ElectronicHorns and Sirens
5522D & 5523D
Explosionproof, DiodePolarized
FEATURES
> Diode polarized for supervisorycircuits
> Corrosion resistant electrostaticheat flowed powder epoxy grayfinish
> Fitted with factory sealed 1/2"(13mm) threaded pipe nipple forquick installation
AGENCY APPROVALS
> UL Listed for Class I, Division 1and 2, Groups B, C, and Dhazardous locations
> UL 464 and 1604 Listed
SPECIFICATIONS
> Speaker swivels 180° vertically orhorizontally depending onorientation of mounting bracket
> 30" (762mm) wire leads
> Horn frequency - 9.82 Hz
> Siren frequency - rises and fallsfrom 600 to 1250 Hz every 8seconds
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-9
11 1/4"(286mm)
11 1/4"(286mm)
18 3/8"(467mm)
Speaker pivots 180°
Signal Off Signal On dB atCat. No. Description Volts Standby Current (Amps) Operating Current (Amps) 10 ft (3.05m)
5522D-AW Horn 20-31V DC 0.061 0.400 109
5523D-AW Siren 20-31V DC 0.061 0.400 105
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-38ELECTRONIC SIGNALS
Adaptatone® MillenniumRemote Speaker/Amp
The Edwards 5532M Adaptatone Millennium Remote Speaker/
Amplifier has been designed for high decibel system operation
when connected to the 5540M Central Tone Generator or 5541M
System Master Panel. See Adaptatone Millennium Tone Generator,
page 4-28.
Each Speaker/Amplifier operates directly from local power sources,
making it possible in a single system to connect the remote
Speaker/Amplifiers to local power sources of different voltages. De-
signed for either 1/2" (13mm) conduit or surface mounting.
The 5532M-485Y6 is designed to be connected to RS485 networks,
allowing full signaling communication control.
The 5532MD-25AW and 5532MD-70AW are diode polarized units
designed for use in applications requiring electrical supervision of
signaling circuit field wiring. The 25AW utilizes a 25 VRMS coupler
board; the 70AW utilizes a 70 VRMS coupler board.
Adaptatone Signaling Systems are designed for industrial applica-
tions calling for high decibel output and microprocessor reliability
combined with simultaneous signal delivery over all speakers in-
cluded in the system. Typical applications include: emergency warn-
ing systems, plant evacuation alarms, security intrusion sirens, pro-
cess monitoring, shift start-and-dismissal horns, and paging sig-
nals.
RS485 units are MEDI compatible. See page 4-10.
5532M & 5532MD SeriesFEATURES
> Output up to 110 dB at 10 ft
> Corrosion resistant electrostaticheat flowed epoxy finish
> Individual volume control
> Suitable for Division 2 Locations
> Captive Components
> RS485 model available
> Diode Polarized models
AGENCY APPROVALS
> NEMA Type 3R
> IP 44
> UL 464 and 1604 Listed
> UL & cUL Listed for indoor andoutdoor application in Class I,Division 2, Groups A, B, C & D;Class II, Division 2, Groups F &G; and Class III HazardousLocations
> cUL C22.2 No. 205
> TUV Rheinland Certified
> CE Marked, LV & EMC Directives(Y6 AC only and AQ models)
SPECIFICATIONS
> 24V DC battery backup terminals
> Speaker can be rotated andlocked in any horizontal direction
System Speaker OperationRS485 Activation
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-39
Operating Signal Off Signal OnCat. No. Voltage Standby Current (Amps) Operating Current (Amps)
5532M-AQ 24V DC 0.10 0.6424V AC 50/60 Hz 0.10 1.22
5532M-N5 120V AC 50/60 Hz 0.10 0.23
5532M-Y6 120V AC 50/60 Hz 0.10 0.28240V AC 50/60 Hz 0.10 0.15
125V DC 0.10 0.15250V DC 0.02 0.08
5532M-485Y6 120V AC 50/60 Hz 0.10 0.28240V AC 50/60 Hz 0.10 0.15
125V DC 0.10 0.15250V DC 0.02 0.08
5532MD-25AW 20 - 24V DC 0.10 0.64
5532MD-70AW 20 - 24V DC 0.10 0.64
Nut to adjustspeakerdirection
Mountingflange4 holes(2 each side)
3 1/2"(89mm)
6"(152mm)
8 47/64"(222mm)
8"(203mm)
13 3/4"(349mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
4"(102mm)
8"(203mm)
2 1/2"(64mm)
D-04
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
4-49
FEATURES
5538-4
> Allows remote activation of up tofour tones
5538-4R
> Allows remote activation of up tofour tones
> Allows the Adaptatone MultipleTone System to be interfaced tolocal/system units for priorityoverride
Adaptatone® RemoteSignal Actuator
The Edwards 5538-4 & 5538-4R Adaptatone Remote Signal Actua-
tors permit an operator to initiate up to four tones from a remote lo-
cation.
Adaptatone signaling systems are designed for industrial applica-
tions calling for high decibel output and microprocessor reliability
combined with simultaneous signal delivery over all speakers in-
cluded in the system. Typical applications include: emergency
warning systems, plant evacuation alarms, security intrusion si-
rens, process monitoring, shift start-and-dismissal horns, and pag-
ing signals. see Adaptatone Signaling System Installation, pg. 4-56.
5538 Series
2 1/8"(54mm)
4 1/8"(105mm)
4 1/2"(114mm)
Provides NormallyOpen Contacts
D-04
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com4-30ELECTRONIC SIGNALS
Adaptatone® MillenniumCentral Tone Generator
The Edwards 5540MV Adaptatone Millennium Central Tone Genera-
tor with Voice messaging has been designed for applications where
simultaneous signaling of a high decibel, heavy duty signal and pre-
recorded voice messaging is required. The tone generator assures
a synchronous signaling sound from all remote speakers. The Mil-
lennium Central Tone Generator produces the 27 standard
Adaptatone sounds and can store 20 seconds of field recorded
voice messages. Four signals may be activated from field-wired,
normally open contacts, or a 24VDC external voltage source such
as an output of a PLC. Normally open contacts can be obtained
from the Cat. No. 5538-4 or Cat. No. 5538-4R Adaptatone Signal Ac-
tuator. See page 4-49.
Messages and tones may be selected by setting miniature dip
switches within the unit. The programmed tones operate on a pyra-
mid-type priority system. For more information on priority tone op-
eration and a complete listing of all 27 tones, see page 4-55.
The 5540MV-485Y6 is designed to be connected to RS485 net-
works, allowing full serial signaling communication control.
Adaptatone Signaling Systems are designed for industrial applica-
tions calling for high decibel output and microprocessor reliability
combined with simultaneous signal delivery over all speakers in-
cluded in the system. Typical applications include: emergency warn-
ing systems, plant evacuation alarms, security intrusion sirens, pro-
cess monitoring, shift start-and-dismissal horns & paging signals.
RS485 units are MEDI compatible. See page 4-10.
5540MV Series
Voice Messaging & SystemSignaling, Four Outputs, RS485
FEATURES
> 27 tone capability - No additionaltone modules needed
> PLC compatible> 20 sec. of field recorded Voice> Suitable for Division 2 Locations> Centralized programmable tone
selection> System-wide priority tone
selection> RS485 model available
AGENCY APPROVALS
> NEMA Type 3R> IP 44> UL 464 and 1604 Listed> UL Listed for indoor and outdoor
applications in Class I, Div. 2,Groups A, B, C & D; Class II, Div.2, Groups F & G; and Class IIIhazardous locations
> cUL Listed C22.2 No. 205> CE Marked - Cenelec LV & EMC
Directives (24Y6 AC model only)
SPECIFICATIONS
> 24V DC battery backup terminals> Built in Presignal tone option on
first message location> Short Circuit protected
D-0
4
ELECTRONIC SIGNALS
© Copyright 2004 Edwards
90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8
www.edwards-s ignals.com
TECHNICAL INFORMATION
4-31
Operating Input Card Signal Off Signal OnCat. No. Voltage Activation Voltage Standby Current (Amps) Operating Current (Amps)
5540MV-24N5 120V AC 50/60 Hz 24VDC 0.10 0.36
5540MV-24Y6 120V AC 50/60 Hz 24VDC 0.10 0.32240V AC 50/60 Hz 0.10 0.20
125V DC 0.10 0.21250V DC 0.02 0.10
5540MV-485Y6 120V AC 50/60 Hz RS485 0.10 0.32240V AC 50/60 Hz 0.10 0.20
125V DC 0.10 0.21250V DC 0.02 0.10
*This device is PLC compatible and may be operated by PLCs with output characteristics that match the input load requirements of this signal.** = Input board designation 24 or 120
SIGNAL INPUT LOAD CHARACTERISTICS* (PLC output to meet following product input parameters)
Operating Max. off state Continuous on Surge (inrush/duration)Cat. No. voltage leakage current (mA) current (mA) Amps/milliseconds
5540MV-24N5 120V 60 Hz 2 360 2.82/4
5540MV-24Y6 120V 60 Hz 2 320 2.82/4
24VDC Input Board 24V DC 2 6 —
Mounting flange4 holes (2 each side)
2 1/2"(64mm)
6"(152mm)
4"(102mm)
1/2" (13mm)conduit mounting
6"(152mm)
8"(203mm)
3 1/2"(89mm)
D-04