Kiwifruit Propagation.pdf

download Kiwifruit Propagation.pdf

of 2

Transcript of Kiwifruit Propagation.pdf

  • 7/27/2019 Kiwifruit Propagation.pdf

    1/2

    9/21/13 Kiwifruit Propagation

    fi le:///C:/Users/H P/Desktop/home group/BM SINGH/crops/kiwi/propagation/Kiwifrui t Propagation.htm

    FN-98-

    Kiwifruit PropagationArlie A. Powell

    Horticulturist-Fruits, Auburn University

    June, 1998

    Kiwifruit propagation is most easily achieved using softwood cuttings taken in June and July and possibly August

    Budding of seedling plants also works fine, but this method is not recommended because of freeze problems.

    Make 2-to 3- node cuttings (2 to 3 leaves) from mature, current season shoots (usually 3 to 6 inches long). The

    leaves should be full size and buds evident at base of leaf petiole. Less mature wood such as the ends of shoots

    will not work.

    In preparing cuttings, cut just below the lowest bud on each stem piece and remove all leaves but the upper one.

    The blade portion of the remaining leaf should be cut in half (removing the outer half). The top part of the cutting

    should be trimmed such that only 1/2 inch or less of stem projects beyond point of attachment of remaining leaf.

    Trim away the bark tissue (with a knife) on two sides of the lower part of the cutting (stem base) for a distance

    of 1/2 to 3/4 inch. This cutting action should just barely slice into both sides of the basal bud. This is referred to

    as wounding.

    The bottom half of cuttings should be immersed in a plant hormone solution for five seconds and then placed into

    a rooting bed or small pots for 60 days or more. During this initial period of callous and root development,

    cuttings should be in a greenhouse (or shadehouse) that only allows about 50% light penetration. Shade cloth

    etc., can be used on greenhouses if necessary. Cuttings must be maintained under intermittent mist (usually 5

    seconds of mist every 5 minutes during daylight hours). If soil (or any media that may be contaminated with soil

    borne fungi) is used in the rooting bed, all the media should be sterilized before use.

    Rooting hormones can be purchased from any number of horticultural supply houses and some farm supply

    stores. Work done in South Carolina indicates a concentration of 6000 ppm of indole - 3- butryic acid (IBA)

    works better than other hormone treatments. However, some of the commercial brand products on the market

    usually contain naphthaleneacetic acid (NAA) or indole acetic acid (IAA) along with IBA. Although not ideal,

    these products usually suffice for kiwi propagation on a small scale. Liquid solutions are best for dipping cuttings

    but powdered forms of commercial products are fine for doing small numbers of cuttings.

    One of the most damaging problems growers in Alabama have experienced in rooting and growing kiwifruit

    plants is dieback of young cuttings (or plants) in the nursery. This is generally caused by soil borne fungi.

    Sterilization of rooting media helps but additional treatments with fungicides may be needed.

    Once cuttings have developed some roots and initiated shoot development, they should be transferred into gallon

    size pots for further development into three- to five-foot plants ready for field planting. Five- to six-foot bamboo

  • 7/27/2019 Kiwifruit Propagation.pdf

    2/2

    9/21/13 Kiwifruit Propagation

    fi le:///C:/Users/H P/Desktop/home group/BM SINGH/crops/kiwi/propagation/Kiwifrui t Propagation.htm

    stakes will be needed for each container for growing straight trunk plants. As plants continue growing in the

    summer months the terminal of each shoot must be pinched when it begins to wind around itself. A new shoot

    must be selected near the point where the terminal was cut and all others removed. Allow this shoot to grow

    upward and continue tying to bamboo stake to form a straight trunk (don't allow stem to wrap around the

    bamboo). Continue to pinch the terminal when it winds around itself and repeat the training process.

    When rooted cuttings are placed in gallon size containers it is usually best to apply a slow release fertilizer (such

    as osmocote or equivalent) at recommended rates usually two times during the growing season (March and July

    are best). Generally 1 teaspoon of slow release fertilizer per gallon pot is adequate. Most of the slow release

    fertilizers being used have analyses such as 18-6-12, 17-7-12 or others with similar ratios.

    Kiwifruit plants have a high water requirement. Plants grown in gallon sized pots should be watered at least daily,

    depending upon potting media used.

    When growing plants in gallon containers there are several options the grower has regarding potting media.

    Standard premix nursery potting media usually works fine. Mixes which some nurseries have used in past years

    such as 1/3 peat, 1/3 soil and 1/3 sand or perlite are quite satisfactory. If soil is used in the mix (or any other

    component which may be contaminated with soil borne fungi), sterilization of the media is recommended beforepotting rooted cuttings.

    Recently nurseries have begun using less costly potting media such as pine bark for growing many plant types.

    This works fine for kiwifruit also. The addition of a small amount of peat moss improves the mix and is

    recommended. Usually 4 or 5 parts bark and 1 part peat is satisfactory. Kiwifruit tolerate low pH, but lime

    should be added to the mix (6 to 10 lbs of agricultural lime per cubic foot of mix is usually adequte) to attain a

    pH of 6 to 6.5. A starter fertilizer such as Pro Start II (or equivalent) should be added at a rate of 6 lbs per cubic

    yard of mix.

    Apply pesticides on an as needed basis. A spray of Benlate plus Captan has worked well on controlling adisease of mature leaves (thought to be alternaria) that usually becomes evident in June and July. Some 2 to 4

    sprays may be needed at 10 to 14 day intervals. A rate of 1/2 lb of Benlate 50W plus 2 lbs Captan 50W per

    100 gallons of water (for dilute spray) works well.

    Brand names used in this publication are for clarity only. The mention of a brand name in no way

    constitutes endorsement of this brand or product by the Cooperative Extension Service. Nor is there

    intended any discrimination against similar unnamed products or brands which may be just as effective.

    Return toFruit Crops

    http://www.aces.edu/http://www.aces.edu/dept/peaches/index.html