KIT 5624 JUNKERS Ju 52 / 3m TRANSPORTmanuals.hobbico.com/rmx/85-5624.pdfJUNKERS Ju 52 / 3m TRANSPORT...

Black Green

Dark Green

Flat Black

Light Gray

Light Olive Green

Yellow

Flat White

Gray

Gunmetal

Steel

Flesh

Tan

Light Blue

* REPEAT SEVERAL TIMES* A REPETER PLUSIEURS FOIS

* CEMENT TOGETHER* A COLLER

* ALTERNATIVE ASSEMBLY* ENSEMBLAGE ALTERNATIVE

* REMOVE AND THROW AWAY* A RETIRER ET JETER

* DO NOT CEMENT* NE PAS COLLER

* OPTIONAL PARTS* PIECES EN OPTION

* DECAL * DECAL COMANIE

This paint guide is provided to complete this kit as shown on the box.

Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte.

Vert noir

Vert foncé

Noir mat

Gris clair

Gris vert

Jaune

Blanc mat

Gris

Bronze

Acier

Chair

Havane

Bleu clair

* Study the assembly drawings.* Each plastic part is identified by a number.* In the assembly drawings, some parts will be

marked by a star (★) to indicate chrome plated plastic.

* For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry.

* Check the fit of each piece before cementing in place.

* Use only cement for polystyrene plastic.* Scrape plating and paint from areas

to be cemented.* Allow paint to dry thoroughly before

handling parts.* Any unused parts may be discarded.

DECAL APPLICATION INSTRUCTIONS

1. Cut desired decal from sheet.2. Dip decal in water for a few seconds.3. Place wet decal on paper towel.4. Wait until decal is movable on paper backing.5. Place decal in position on model, face up and

slide backing away.6. Press out air bubbles with a soft damp cloth.7. Milkiness that may appear is for better decal

adhesion and will dry clear. Wipe away any excess adhesive.

8. Do not touch decal until fully dry.9. Allow the decals 48 hours to dry before

applying clear coat.

NOTE: Decals are compatible with setting solutions or solvents.

READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER

* Etudier les schémas de montage.* Chaque pièce en plastique est identifiée par un numéro.* Sur les schémas de montage, certaines pièces sont

marquées d'une étoile (★) pour indiquer qu'elles sont en plastique chromé.

* Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air.

* Vérifier que chaque pièce s'ajuste bien avant de la coller en place.

* N'utiliser que de la colle pour polystyrène.* Gratter les parties à coller pour enlever le chrome et la peinture.* Laisser la peinture bien sécher avant de manipuler les pièces.* Toute pièce inutilisée peut être jetée.

DIRECTIVES D'APPLICATION DES AUTOCOLLANTS

1. Découper l'autocollant désiré de la feuille.2. Tremper l'autocollant dans de l'eau pendant quelques secondes.3. Placer l'autocollant mouillé sur une serviette en papier.4. Attendez que l'autocollant puisse être déplacé sur son support

en papier.5. Mettre l'autocollant en position sur le modèle face sur

le dessus et faire glisser le support pour l'enlever.6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.7. La substance laiteuse qui peut apparaître est destinée à

améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif.

8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.9. Laisser l'autocollant sécher pendant 48 heures avant

d'appliquer une couche transparente.

REMARQUE: Les autocollants sont compatibles avec les solutions de fixage ou les solvants.

KIT 5624 85562400200

If you have any questions or comments, call our hotline at: (800) 833-3570or, please write to:

Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007Be sure to include the plan number (85562400200), part number, description, your return address and phone number.

Visit our website: www.revell.com

Revell Inc Elk Grove Village, IL. Copyright © 2009. All rights reserved.

JUNKERS Ju 52 / 3m TRANSPORT

Originally developed and used as a peacetime commer-cial airliner, the Ju52 made its maiden flight in 1932. At the start of World War II, when Germany invaded Poland, the Luftwaffe's Transportverband had an inventory of 547 Ju52/3ms. The Ju52 was taylor-made to supply fast moving troops and advanced paratrooper deployment, the Ju52 was a real "workhorse".

floor / cockpit ASSEMBlY1

Kit 5624 -

47FUSELAGE

FLOORGRAY

67CONTROL

YOKEFLAT BLACK

66COLUMN

GRAY

66CONTROL COLUMN

GRAY

70RIGHT

ADJUSTMENT HANDLE

GRAY

71LEFT

ADJUSTMENT HANDLE

GRAY

65CONSOLEGRAY WITHFLAT BLACK

DETAILS

64INSTRUMENT

PANELFLAT BLACK WITH

GRAY INSTRUMENTS AND WHITE DETAILS

48BULKHEAD

GRAY

50BULKHEAD

GRAY

49BULKHEAD

GRAY25

HANDRAILGRAY

62RIGHT

CABIN DOORGRAY

60PILOT'S SEAT

GRAY WITH WHITE STRAPS AND

STEEL BUCKLES

61CO-PILOT'S SEAT

GRAY WITH WHITE STRAPS AND

STEEL BUCKLES

68LEFT

CABIN DOORGRAY

135WINDOW

CLEAR

1DECAL

48ATABLE

GRAY

uSE thE point of A ModEling knifE to opEn up All holES which ArE indicAtEd on thE BottoM of thE pArt. thErE ArE A totAl of

ElEvEn holES to BE opEnEd.

LEFT FUSELAGE ASSEmbLy2

Kit 5624 -

105AFT

BULKHEADGRAY

113LEFT

SIDE WINDOWSCLEAR

114CIRCULAR WINDOW

CLEAR

1LEFT FUSELAGE

HALFGRAY

(INTERIOR ONLY)

45LEFT INTERIOR FRAMEWORK

GRAY51BULKHEAD

GRAY

55SEAT

LIGHT GRAYWITH WHITE BELTS

AND STEEL BUCKLES

53BENCH SEATS


ANDSTEEL BUCKLES

120GUNNER'S LADDER

GRAY

54HANDRAIL

GRAY

58SEAT


AND STEEL BUCKLES

56SEAT LEGSGRAY

59SEAT LEGS

GRAY

52GUNNER'S

FLOORGRAY

CAREFULLy REmOVE ALL OVERFLOW

TAbS

NOTE: GLUE FUSELAGE FLOOR ASSEmbLy TO THE FUSELAGE

SIDE FIRST, THEN ATTACH HANDRAIL. LADDER AND SEATS

APPLy GLUE TO THE

GUNNER'S FLOOR ONLy

right FUSELAgE SiDE ASSEMBLY3

FUSELAgE BottoM4

Kit 5624 -

NotE: oPEN UP thE hoLES iN thE

FUSELAgE BottoM For thE MiLitArY AND AMBULANCE

VErSioNS AS iNDiCAtED iN thiS DrAWiNg. oPEN UP thE tWo

PANELS AS iNDiCAtED For thE MiLitArY VErSioN oNLY.

SEE StEPS #9 AND #10 For oPtioNAL LANDiNg gEAr

ASSEMBLiES

CArEFULLY rEMoVE ALL oVErFLoW

tABS

112RIGHT

SIDE WINDOWSCLEAR

46RIGHT

INTERIOR FRAMEWORKGRAY

53BENCH SEATS

GRAY

26TAIL WHEEL

FLAT BLACK TIRE,GLOSS BLACK

WHEEL

3FUSELAGE BOTTOM

MILITARYAND

AMBULANCE

REMOVE THESE TWO PANELS FOR THE MILITARY

VERSION ONLY

MILITARY

MILITARY

AMBULANCE

AMBULANCE

AMBULANCE

134CRANK

GRAY

63HANDLE

GRAY

2RIGHT

FUSELAGE HALFGRAY

(INTERIOR ONLY)

FUSELAGE TOP ASSEMBLY6

FUSELAGE BOTTOM ASSEMBLY5

Kit 5624 -

TOP HATCH CAN BE OPENED UP TO SHOW

THE FUSELAGE ITERIOR

UNDERSIDE VIEW SHOWING COLLECTOR IN

PLACE

FUSELAGE ASSEMBLY

OPEN HOLE

OPEN HOLE

4FUSELAGE TOP

GRAY(INTERIOR ONLY)

137HOISTGRAY

82EXHAUST COLLECTOR

STEEL

132CONTROL BOX

GRAY

138GENERATOR

BRACKETGRAY

69RADIO

FLAT BLACK

136CABIN LIGHT

CLEAR136

CABIN LIGHTCLEAR

136CABIN LIGHT

CLEAR

133RUDDER

CONTROL ROD

WING ASSEMBLY7

STABLIZER ASSEMBLY8

Kit 5624 -

WINGS TO FUSELAGE

103LEFT

ELEVATOR

20LEFT

HORIZONTAL STABILIZER

TOP

22RIGHT

HORIZONTAL STABILIZER

TOP

23RIGHT

HORIZONTAL STABILIZERBOTTOM

21LEFT

HORIZONTAL STABILIZERBOTTOM

104RIGHT

ELEVATOR

6LEFT

WING TOP

7RIGHT

WING TOP

8LEFT

WING BOTTOM

9RIGHT

WING BOTTOM

LEFT RIGHT

STABLIZER ASSEmBLy CONTINUED8

mILITARy LANDING GEAR ASSEmBLy9

AmBULANCE LANDING GEAR ASSEmBLy10

Kit 5624 -

24STRUT

24STRUT

33OUTER

MAIN WHEEL

33OUTER

MAIN WHEEL

33OUTER

MAIN WHEEL33OUTER

MAIN WHEEL

32INNER

MAIN WHEEL

32INNER

MAIN WHEEL

32INNER

MAIN WHEEL32INNER

MAIN WHEEL

95LEFT INNER

WHEEL COVER

93RIGHT INNER

WHEEL COVER

101LEFT MAIN

GEAR STRUT

102RIGHT MAINGEAR STRUT

107LEFT

REAR STRUT97

RIGHT REAR STRUT

94LEFT OUTER

WHEEL COVER

92RIGHT OUTERWHEEL COVER

29LEFT

MAIN STRUT

30RIGHT

MAIN STRUT

31LEFT

AFT STRUT106

RIGHT AFT STRUT

30ABRACKET29A

BRACKET

101ABRACKET

102ABRACKET

LEFT

LEFT

LEFT

RIGHT

RIGHT

RIGHT

MILITARY VERSION DUST BIN ASSEMBLY11

RIGHT ENGINE ASSEMBLY12

Kit 5624 -

RETRACTED POSITION EXTENDED POSITION

MARK THESE LOCATIONS ON THE BACK SIDE OF THE CYLINDERS BEFORE ASSEMBLING THE

ENGINE.

NOTE: THE OPEN SPACE ON THE COVER FITS TO THE BOTTOM OF THE CYLINDERS.

FRONT BACK

36COVER

FLAT BLACK GRAY CRANKCASE

GRAY CRANK-

CASE

37CRANKCASE AND

PUSH RODSFLAT BLACK

57CYLINDERS

(FRONT SIDE)STEEL

98GUN MOUNT

GRAY

78MACHINE GUN

GUNMETAL

79MAGAZINEFLAT BLACK

118DUST BIN WINDOW

CLEAR

99RIGHT

DUST BIN CLEAR

(SAME COLOR AS THE FUSELAGE)

100LEFT

DUST BIN CLEAR

(SAME COLOR AS THE FUSELAGE)

96BUCKET

96BUCKET

LEFT ENGINE ASSEMBLY13

RIGHT ENGINE ASSEMBLY CONTINUED12

Kit 5624 -

MARK THESE LOCATIONS ON THE BACK SIDE OF THE CYLINDERS BEFORE ASSEMBLING THE

ENGINE.


FRONT BACK

142INTAKE MANIFOLD

STEEL

141LEFT

INTAKE MANIFOLDSTEEL

109RIGHT

UPPER EXHAUST MANIFOLD

STEEL

43LEFT

UPPER EXHAUST MANIFOLDSTEEL

108RIGHT

LOWER EXHAUST MANIFOLD

STEEL

42LEFT

LOWER EXHAUST MANIFOLD

STEEL

17COWLING

INNER HALFGRAY

(INTERIOR ONLY)

15INNER HALF

COWLING GRAY

(INTERIOR ONLY)

16COWLING

OUTER HALFGRAY

(INTERIOR ONLY)

14OUTER HALF

COWLING GRAY

(INTERIOR ONLY)

36COVER

FLAT BLACK

GRAYCRANKCASE

37CRANKCASE AND

PUSH RODSFLAT BLACK

57RIGHT

CYLINDERS(REAR SIDE)

140LEFT

CYLINDERS(REAR SIDE)

140LEFT

CYLINDERS(FRONT SIDE)

STEEL

ENGINEs TO WING AssEMBLY14

CENTER ENGINE AssEMBLY15

Kit 5624 -


MARK THESE LOCATIONS ON THE BACK SIDE OF THE CYLINDERS BEFORE ASSEMBLING

THE ENGINE.

FRONT BACK

36COVER

FLAT BLACK

GRAYCRANKCASE

37CRANKCASE AND

PUSH RODSFLAT BLACK

38CYLINDERS

(FRONT SIDE)STEEL

38CYLINDERS(REAR SIDE)

39INTAKE MANIFOLD

STEEL

40LEFT EXHAUST

MANIFOLDSTEEL

41RIGHT EXHAUST

MANIFOLDSTEEL

RIGHT LEFT

CENTER ENGINE assEmbly CoNTINuEd15

uNdERsIdE assEmbly16

Kit 5624 -

ComPlETEd CENTER ENGINE

NoTE: oNE ENd oF THE PaRT (82a) FITs INTo THE boTTom HolE oN THE REaR oF THE CylIINdERs. THE oTHER ENd FITs INTo THE

EXHausT CollECToR WHICH Was GluEd To THE uNdERsIdE oF THE FusElaGE IN sTEP (5). aNy sEPaRaTIoNs IN THE EXHausT PIPEs

CaN bE FIllEd WITH INsTaNT GluE.

uNdERsIdE VIEW

sHoWING PRoPER

loCaTIoN FoR all PaRTs aFTER

assEmbly

82AEXHAUST PIPE

STEEL

EXHAUST COLLECTOR

11LEFT FLAP

10RIGHT FLAP

80PUSH RODS

80PUSH RODS

119LANDING

LIGHTCLEAR

5COWLING

UNDERSIDE ASSEMBLY CONTINUED16

TOpSIDE ASSEMBLY17

Kit 5624 -

44OIL COOLER INTAKE

FILTERS

44OIL COOLER INTAKE

FILTERS12

ANTENNAFLAT BLACK

34PITOT PROBESAME COLOR AS

SURROUNDING WING

PAINT BLADES BLACK-GREENPAINT CENTER SECTIONS

FLAT BLACK

STEEL

130INDICATOR

143INDICATOR

131PUSH ROD

131PUSH ROD

72ANTENNA

35PROPELLERS

73GENERATOR

74RIGHT

LOOP ANTENNA

75LEFT

LOOP ANTENNA

130INDICATOR

13ANTENNASUPPORTFLAT BLACK

final assembly18

paratroopers assembly19

Kit 5624 -

tHe German paratrooper Uniform inClUDeD a tan pUlloVer WitH meDiUm Gray pants anD blaCK boots. tHe Helmets Were a steel Gray, anD tHe paraCHUte paCKs Were UsUally neUtral or

liGHt Gray WitH flat WHite straps anD steel bUCKles. tHe faCes anD HanDs sHoUlD be painteD a flesH Color.

Door may be assembleD open or CloseD.

111CANOPY

CLEAR

79MAGAZINEFLAT BLACK

78MACHINE GUN

GUNMETAL

77 GUN SUPPORT

GRAY

76 GUN RING

GRAY

81 GUN SEAT

GRAY

117SHIELDCLEAR

116WINDOW

CLEAR

27DOORGRAY

(INTERIOR ONLY)

28LADDER

GRAY

91PARACHUTE

87BODY

89RIGHT ARM 90

LEFT ARM

86PARACHUTE

126BODY

84RIGHT ARM

124RIGHT ARM 128

LEFT ARM

129PARACHUTE

83BODY

121BODY

127RIGHT ARM

85LEFT ARM

125PARACHUTE

123LEFT ARM

88LEG

122LEGS

DECAL PLACEMENT20

Kit 5624 -

DECAL PLACEMENT21

Kit 5624 -

decal placement22

Kit 5624 -

KIT 5624 JUNKERS Ju 52 / 3m TRANSPORTmanuals.hobbico.com/rmx/85-5624.pdfJUNKERS Ju 52 / 3m TRANSPORT...

Documents

Transcript of KIT 5624 JUNKERS Ju 52 / 3m TRANSPORTmanuals.hobbico.com/rmx/85-5624.pdfJUNKERS Ju 52 / 3m TRANSPORT...