Kettenkrad - Zoukei-mura Official WebsiteProceed with the Kettenkrad kit assembly after attaching...
1
Photo-Etched Set ¥1,800 (税込 ¥1,890 ) These parts are made of metal. Please handle with care. These parts cannot be glued with plastic model kit cement. Instant glue should be used instead. The 1/32 “Kettenkrad” is sold separately. The kit is not included in this set. ©ZOUKEI-MURA INC. All Rights reserved. Photo-Etched Set ©ZOUKEI-MURA INC. All Rights reserved. ¥1,800 ( 税込¥1,890 ) This set consists of 1 sheet of photo-etched parts, 4 turned metal parts (3 different kinds) and 1 film for reproducing the meters. http://www.zoukeimura.co.jp/ 4 518992 503684 ●This item is meant for hobbyists 15 years of age or older. Please do not give this item to children under 15. ●This item is intended for use with the Zoukei-mura 1/32 "Kettenkrad". ●The polyethylene bags that contain the parts and assembly manual present a suffocation risk. Please do not drop the parts or bend them in unintended ways, as they may be damaged. ●In order to properly express the shape of the sculpts, it was unavoid- able for some parts to have sharp edges. Please be careful. Attention! How to assemble the“Photo-Etched Set”with the“Kettenkrad”kit ■Photo-Etched parts × 1 sheet ■Film × 1 sheet ■Stay × 2 ■Stay ■Stay ■Lever (short) ■Lever (short) ■Lever (long) ■Lever (long) ◆Turned metal parts (3 kinds) × 4 Chart of Included Parts ◆◆Important Points for Assembly◆◆ ■Please carefully read this assembly manual prior to opening, and make sure that everything is included. When using these parts, please read these instructions as well as the “Kettenkrad Instruction Manual”. ■To use this item, tools such as ●nippers (or scissors) for photo-etched ●tweezers ●pin vise and 0.5mm drill blade ●0.3mm diameter brass rod ●instant glue etc. are required, so please prepare them. ■The photo-etched and metal parts of this kit are used to replace the original plastic parts. Depending on where to use the parts, sharpening, cutting or altering the original plastic parts are required before attaching them. Please double check before assembly. When assembling, adjust the orientation of each part while checking the balance and pose of the entire kit. ■ Use instant glue to cement the parts. Please be careful that these parts cannot be glued with plastic model kit cement. A coat of metal primer is required before painting. (Otherwise the paint will peel off.) ■The recommended brand for painting your kit is the latest line of paint from Vallejo Color. While referring to historical resources on the Luftwaffe and Heer, you may paint the model with the coloring of your choice. ※Please use caution when handling the tools and solvents used for assembly and painting by referring to their instruction manuals. Add this photo-etched set while assembling your Kettenkrad kit. Please carefully refer to the “Kettenkrad Instruction Manual”. 1 Engine SWPS01-M03 SWPS01-M03 ZOUKEI-MURA INC. PRESENTS SUPER WEAPON SERIES No.01 ZOUKEI-MURA INC. PRESENTS SUPER WEAPON SERIES No.01 SUPER WEAPON OPTIONS SUPER WEAPON OPTIONS Marks Used in the Instructions Colors Used in the Instructions B-5 A-14 B-2 Make a hole. Replace the default part. Work on this original part and attach. Bend by adjusting to the original part of the kit. This attaches to part A-13. Cut off this mold and replace it by the photo-etched part. Part A-14 is not needed. It will replaced by photo-etched parts 1 and 2. Part A-14 will be replaced by photo-etched parts 1 and 2. Attach 12pcs of photo-etched parts 23 to each driving wheel (parts B-11 and B-12). Attach the photo-etched parts instead of parts B-1 and B-2. Bend slightly to imitate mudguards. The molded surfa should be on the ou Bend by adjusting to the original part of the kit. Prepare a 0.3mm diameter slip of brass rod, and then use it as shown. Prepare a 0.3mm diameter slip brass rod, and use it as shown. Bend as shown. Cut these levers off. Drill two 0.5mm diameter holes. Cut off. Scrape away. Bend. Do the same for right and left. Parts from the original kit. Photo-etched parts. Show metal parts. 1/32“Kettenkrad Instruction Manual” 2 Chassis 1/32“Kettenkrad Instruction Manual” 3 Body 1/32“Kettenkrad Instruction Manual” 6 Front fork 1/32“Kettenkrad Instruction Manual” 45Caterpillar 1/32“Kettenkrad Instruction Manual” B-5 Work on the molds. Work on the molds. Photo-etched part 19 reproduces the concave molds. Please press the molds with a burnisher, an old ballpoint pen or a spatula. Please choose and use a tool which size fits the molds. Proceed as for photo-etc by working on the mold ( Please process on a soft surface (sheet of rubber, thick magazine etc.). Attach by adjusting to the original part of the kit. Attach to part A-1. As shown, cut off these sections of parts A-1 and A-2, and attach the stay and the photo-etched parts 19. Adjust to part A-2. Adjust to part A-1. Attach to part A-2. A-1 A-1 A-2 A-14 Attach by adjusting to the original part of the kit. Bend by adjusting to the original part of the kit. Assemble 2 sets. Bend photo-etched parts 5 and 8, while inserting part 6 between them. Assemble left and right sides in the same way. As shown, assemble the Kettenkrad kit while inserting the photo-etched parts to complete your build. Build the pivot by wrapping the 0.3mm diameter slip of brass rod. This side has a convex mold. A-2 This side has a convex mold. Prepare a 0.3mm diameter slip of brass rod, and then use it as shown. A-11 B-31 A-3 B-11 B-12 Prepare a 0.3mm diameter slip of brass rod, and then use it as shown. Prepare a 0.3mm diameter slip of brass rod, and then use it as shown. In case you would like to attach a hood, tie some rolled up tissue paper, and affix in 3 points with photo-etched part 24 and a slip of brass rod. Hold these two parts together and insert the brass rod. Be careful: do not put too stress on the parts. Proceed with the Kettenkrad kit assembly after attaching each photo-etched part. Attach to 2 points on part A-3. ※ ※ ※ Assemble left and right sides in the same way. B-23 B-24 B-1 Kettenkrad Kettenkrad These are extra parts to be used with the “Kettenkrad” kit. These are extra parts to be used with the “Kettenkrad” kit. 1/32 Kettenkrad 1/32 Kettenkrad These are extra parts to be used with the “Kettenkrad” kit. These are extra parts to be used with the “Kettenkrad” kit. 1/32 Kettenkrad 1/32 Kettenkrad These are extra parts to be used with the “Kettenkrad” kit. These are extra parts to be used with the “Kettenkrad” kit. 1/32 1/32 ■Plan & Design : Zoukei-Mura Inc. ■Manufacturer : ABER ■Distributor : VOLKS Inc. http://www.volks.co.jp/en/index.aspx 60 Goshonouchi Nakamachi Shichi-jo, Shimogyo-ku, Kyoto Japan 600-8862 Please note that items which have been opened, or worked with, can't be exchanged.Thank you for your understanding. We take the utmost of care when overseeing manufacturing, but if your kit is among the very small percentage that contains a defective part, please contact customer service within two weeks of your purchase with your full name and order number. Purchasers from VOLKS Japan International Web Site : Please contact [email protected]. Purchasers from VOLKS USA : Please contact [email protected].
Transcript of Kettenkrad - Zoukei-mura Official WebsiteProceed with the Kettenkrad kit assembly after attaching...
Photo-Etched Set
¥1,800 (税込¥1,890)
These parts are made of metal. Please handle with care.These parts cannot be glued with plastic model kit cement. Instant glue should be used instead.The 1/32 “Kettenkrad” is sold separately. The kit is not included in this set.
©ZOUKEI-MURA INC. All Rights reserved.
Photo-Etched Set
©ZOUKEI-MURA INC. All Rights reserved.
¥1,800 (税込¥1,890)
This set consists of 1 sheet of photo-etched parts, 4 turned metal parts (3 different kinds) and 1 film for reproducing the meters.
http://www.zoukeimura.co.jp/
4 518992 503684
●This item is meant for hobbyists 15 years of age or older. Please do not give this item to children under 15.
●This item is intended for use with the Zoukei-mura 1/32 "Kettenkrad".
●The polyethylene bags that contain the parts and assemb ly manua l present a suffocation risk. Please do not drop the parts or bend them in un intended ways, as they may be damaged.
●In order to proper ly express the shape of the sculpts, it was unavoid-able for some parts to have sharp edges. Please be careful.
Attention!
How to assemble the “Photo-Etched Set” with the “Kettenkrad” kit
■Photo-Etched parts × 1 sheet■Film × 1 sheet
■Stay × 2
■Stay■Stay
■Lever (short)
■Lever (short)
■Lever (long)
■Lever (long)
◆Turned metal parts (3 kinds) × 4
Chart of Included Parts ◆◆Important Points for Assembly◆◆
■Please carefully read this assembly manual prior to opening, and make sure that everything is included. When using these parts, please read these instructions as well as the “Kettenkrad Instruction Manual”.
■To use this item, tools such as ●nippers (or scissors) for photo-etched ●tweezers ●pin vise and 0.5mm drill blade ●0.3mm diameter brass rod ●instant glue etc. are required, so please prepare them.
■The photo-etched and metal parts of this kit are used to replace the original plastic parts. Depending on where to use the parts, sharpening, cutting or altering the original plastic parts are required before attaching them. Please double check before assembly. When assembling, adjust the orientation of each part while checking the balance and pose of the entire kit.
■ Use instant glue to cement the parts. Please be careful that these parts cannot be glued with plastic model kit cement. A coat of metal primer is required before painting. (Otherwise the paint will peel off.)
■The recommended brand for painting your kit is the latest line of paint from Vallejo Color. While referr ing to histor ical resources on the Luftwaffe and Heer, you may paint the model with the coloring of your choice.
※Please use caution when handling the tools and solvents used for assembly and painting by referring to their instruction manuals.
Add this photo-etched set while assembling your Kettenkrad kit. Please carefully refer to the “Kettenkrad Instruction Manual”.
1 Engine
SWPS01-M03SWPS01-M03ZOUKEI-MURA INC. PRESENTS SUPER WEAPON SERIES No.01 ZOUKEI-MURA INC. PRESENTS
SUPER WEAPON SERIES No.01
SUPER WEAPON OPTIONS SUPER WEAPON OPTIONS
Marks Used in the Instructions
Colors Used in the Instructions
B-5
A-14
B-2
Make a hole.
Replace the default part.
Work on this original part and attach.
Bend by adjusting to the original part of the kit.
This attaches to part A-13.
Cut of f th is mold and replace it by the photo-etched part.
Part A-14 is not needed. It will be r e p l a c e d b y photo -etched parts 1 and 2.
Part A-14 will be replaced by photo-etched parts 1 and 2.
A t t a c h 1 2 p c s o f photo-etched parts 23 to each driving wheel (parts B-11 and B-12).
A t t ac h t he photo-etched parts instead of parts B-1 and B-2.
Bend s l ight ly to imitate mudguards.
T h e m o l d e d s u r f a c e should be on the outer side.
Bend by adjusting to the or ig inal par t of the kit.
P r e p a r e a 0 . 3 m m diameter slip of brass rod, and then use it as shown.
Prepare a 0.3mm diameter slip of brass rod, and then use it as shown.
Bend as shown.
Cut these levers off.
Drill two 0.5mm diameter holes.
Cut off.
Scrape away.
Bend.
Do the same for right and left.
Parts from the original kit.
Photo-etched parts.
Show metal parts.
1/32“Kettenkrad Instruction Manual”
2 Chassis1/32“Kettenkrad Instruction Manual”
3 Body1/32“Kettenkrad Instruction Manual”
6 Front forks1/32“Kettenkrad
Instruction Manual” 4 5 Caterpillar1/32“Kettenkrad
Instruction Manual”
B-5
Work on the molds.
Work on the molds.
P h o t o - e t c h e d p a r t 19 reproduces the concave molds. Please press the molds with a burnisher, an o l d b a l l p o i n t p e n o r a spatula. Please choose and use a tool which size f its the molds.
Proceed as for photo-etched part 19, by working on the mold (back side).
Please process on a soft surface (sheet of rubber, thick magazine etc.).
Attach by adjusting to the original part of the kit.
Attach to part A-1.
As shown, cut off these sections of parts A-1 and A-2, and attach the stay and the photo-etched parts 19.
Adjust to part A-2.
Adjust to part A-1.
Attach to part A-2.A-1
A-1
A-2A-14
Attach by adjusting to the original part of the kit.
Bend by adjusting to the original part of the kit.
Assemble 2 sets.
Bend photo-etched parts 5 and 8, while inserting part 6 between them.
Assemble left and right sides in the same way.
As shown, assemble the K e t t e n k r a d k i t w h i l e inserting the photo-etched parts to complete your build.
Build the pivot by wrapping the 0.3mm diameter slip of brass rod.
This side has a convex mold.
A-2
This side has a convex mold.
Prepare a 0.3mm diameter slip of brass rod, and then use it as shown.
A-11
B-31
A-3
B-11 B-12
Prepare a 0.3mm diameter slip of brass rod, and then use it as shown.
Prepare a 0.3mm diameter slip of brass rod, and then use it as shown.
In case you would like to attach a hood, tie some rolled up tissue paper, and affix in 3 points with photo-etched part 24 and a slip of brass rod.
Hold these two parts together and insert the brass rod.Be careful: do not put too stress on the parts.
Proceed with the Kettenkrad kit assembly after attaching each photo-etched part.
Attach to 2 points on part A-3.
※
※
※
Assemble lef t and right sides in the same way.
B-23
B-24
B-1
KettenkradKettenkradThese are extra parts to be used
with the “Kettenkrad” kit.These are extra parts to be used
with the “Kettenkrad” kit.
1/32 Kettenkrad1/32 KettenkradThese are extra parts to be used
with the “Kettenkrad” kit.These are extra parts to be used
with the “Kettenkrad” kit.
1/32 Kettenkrad1/32 KettenkradThese are extra parts to be used
with the “Kettenkrad” kit.These are extra parts to be used
with the “Kettenkrad” kit.1/321/32
■Plan & Design : Zoukei-Mura Inc. ■Manufacturer : ABER■Distributor : VOLKS Inc. http://www.volks.co.jp/en/index.aspx 60 Goshonouchi Nakamachi Shichi-jo, Shimogyo-ku, Kyoto Japan 600-8862
Please note that items which have been opened, or worked with, can't be exchanged.Thank you for your understanding.
We take the utmost of care when overseeing manufacturing, but if your kit is among the very small percentage that contains a defective part, please contact customer service within two weeks of your purchase with your full name and order number.Purchasers from VOLKS Japan International Web Site :Please contact [email protected] from VOLKS USA : Please contact [email protected].
