Katalogy Control Tech b113 Pubs 1492215

Analog Programmable Controller WiringSystems(Catalog Number 1492-AIFM__-__-__)

Product Data

ContentsThis product data contains:

Section Page

Description 3

Wiring System Features and Benefits 3

Features and Benefits of Pre-wired Cables 4

AIFM Options and Features 4

Feedthrough Modules 5

Fusible Modules 6

Accessories 8

How to Order Pre-wired Cables and AIFMs 9

AIFM Catalog Number Explanation 9

Cable Catalog Number Explanation 10

Pre-wired Cable and AIFM Selection Table for Analog I/O Modules 10

Cable Technical Section 12

Pre-wired Cable Specifications 12

Pre-wired Cable Pinouts 13

AIFM Technical Section 15

Specifications, Application Notes, and Pinouts 16

Dimensions 25

Adhesive Label Cards 26

Field-Side Wiring Diagrams 33

Reference Publications 57

2 Analog Programmable Controller Wiring Systems

The Bulletin 1492 Analog Programmable Controller Wiring SystemProduct Line consists of Analog Interface Modules (AIFMs) and Pre-wiredCables. These products are designed to aid in the installation ofAllen-Bradley Programmable Controller Analog I/O Modules.

AIFMs and pre-wired cables replace the terminal blocks and up to 50% ofthe point-to-point wiring between the programmable controller and fielddevices. They are available for over 20 different 4-, 6-, 8-, and 16-channel1746 SLC 500, 1756 ControlLogix, and 1771 PLC analog I/O modules.AIFMs allow you to conveniently incorporate additional terminations andovercurrent protection into your I/O circuitry.

Faster Installation TimePre-wired cables have the I/O module terminal block or wiring armalready wired-up on one end and a D-shell connector on the other. Noneed to measure, cut, strip, label, and terminate 20 to 40 wires per I/Omodule. Simply attach the wiring arm or removable terminal block end ofthe cable to the I/O module and attach the D-shell connector end of thecable to the AIFM — and you are ready to wire out to field devices.

Successful System Start-upsThe pre-wired cables are 100% tested for continuity. No more crossedwires and loose connections between the I/O module and the terminalblocks on the DIN rail. With the pre-wired cable and AIFM, yourapplication will have a much higher rate of success at initial start-up.

Simplified TroubleshootingFusible AIFMs provide termination for input modules as well as the abilityto incorporate overcurrent protection for transmitters. On-board 24Vblown fuse indicators help to quickly identify which input had the fault —reducing costly troubleshooting and downtime.

Reduced Panel SpaceAll of the AIFMs have field-side wiring terminals for the I/O channels aswell as extra terminals for the I/O device shield connections. Most inputAIFMs also have extra terminals that are internally commoned togetherand can be used as power busses for input devices. No additional terminalblocks are needed to provide power to the 2-, 3-, and 4-wiretransmitters — saving valuable panel/DIN rail space. Just bring in onepower connection per group to the commoned terminals and terminate theother side of your input devices to the power bus. Complete and compactwiring all on one AIFM!

Quality-Looking PanelThe pre-wired cables and AIFMs organize your wiring and terminationsfor a consistent look to your panel. Pre-printed adhesive labels for theterminal wiring neatly identify field-side connections.

Description

Features and Benefits ofAnalog Wiring Systems

3Analog Programmable Controller Wiring Systems

Pre-wired cables have the I/O module removable terminal block or wiringarm already wired up on one end and a D-shell connector on the other toattach to the AIFM. They are available for over 20 different 4-, 6-, 8-, and16-channel 1746 SLC 500, 1756 ControlLogix, and 1771 PLC analog I/Omodules. All of the pre-wired cables are 100% tested for continuity to helpensure a positive connection.

Cables Fit Your PanelAll of the Bulletin 1492 pre-wired analog cables are offered in fourstandard lengths of 0.5m, 1.0m, 2.5m, and 5.0m to fit a variety ofapplications. Custom length cables (made to order) are also available.

Secure ConnectionsAll cables have a 15- or 25-pin D-shell connector with a slide-lockingmechanism for secure connection to the AIFM.

Maintained Signal IntegrityMost cables utilize twisted pairs and all have an overall shield to aid noiseimmunity of low-level analog signals.

Convenient GroundingMost cables have a prepared drain wire with a ring lug at the I/O moduleend of the cable for convenient grounding of the cable shield to thechassis, if desired. Other cables directly terminate the drain wire to aninternally grounded shield terminal on the I/O module connector.

AIFMs, similar to groups of terminal blocks, are available with either 15-or 25-pin D-shell connectors. The number of field-side wiring terminalsvaries with the type of module — from three to five terminals per I/Ochannel. AIFMs are available as feed-through or fusible to customize thewiring system to your application.

All of the AIFMs have the following features:

Polarized D-shell connector for easyinstallation. Pre-wired cable has matingD-shell connector with slide-lockingmechanism for secure connection.

Pre-printed and blank adhesive markingstrips are provided to identify either theprogrammable controller I/O field-sidewiring terminals or your own applicationrequirements.

High-density field-side wiring terminalsallow more connections in less spaceand accommodate #22-12 AWG wire.

Continuous current rating of 2 amps percircuit supports higher-currentprogrammable controller output modules.

Standard DIN #3 rail mounting for quickinstallation.

UL Component Recognized(File E113724 Guide NRAQ2);UL recognized per Canadian SafetyStandards (cUR)(File E113724 Guide NRAQ2);and CE Approved.

Large rectangular write-on area acts asbuilt-in group marking carrier forprogrammable controller rack, modulegroup, and/or slot information.

Features and Benefits ofPre-wired Cables

AIFM Options and Features


Feed-through Modules

Feed-through AIFMs have three terminals per I/O channel to wire the I/Omodule connections and device shield. The shield terminals are internallybussed together and also tied to the D-shell housing to connect with thecable shield. Some feed-through AIFMs also have special features listedbelow.

The 1492-AIFM4-3, when used with the 1771-OFE2 and -OFE3, providesselectable current limiting resistors. Simply flip a DIP switch to add the250 ohms series impedance into the output circuit. As a troubleshootingaid, test point loops access the circuit on either side of the series resistorand can be used to measure output circuit voltage/current. The limitingresistors are configured on a per channel basis.

The 1492-AIFM6TC-3 for the 1756-IT6I provides on-board cold junctioncompensation to allow thermocouples to be connected “remotely” whilestill correcting for temperature at the termination point. The combinationthermistor and isothermal bar acquire temperature data at the AIFM forthe thermocouple module to adjust the input value.

The 1492-AIFM8-3 has 8 extra terminals commoned together in a powerbus that can be used for Module Common connections or power supplyconnections. The extra terminals and internal jumpering eliminate theneed for some terminal blocks for power connections and jumperaccessories.

Below are examples of the field-side connections available on thefeed-through AIFMs.

4-Wire Transmitter Input

Output

AIFM

Pre-wired Cable

AIFM

Pre-wired Cable

Analog Input Module

Analog Output Module

Power Supply Transmitter

Channel 1+

Channel 1–

SHIELD

1+

1–

LOAD

OUT 0

ANL COMC

SH

0


Fusible Modules

Fusible AIFMs are available for analog input modules. These AIFMsenable you to fuse the input device power source on the field-side. Thefield-side power source is distributed through individual on-board5 x 20mm fuse clips. The AIFMs have 24V DC blown fuse indicators toreduce the troubleshooting time to locate and replace a blown fuse.Standard fuse holders reside in the AIFM aiding in the removal of the fusewith a fuse puller (fuses are not included). Isolation switch plugs or“dummy fuses” (see Accessories, page 7) are also available to isolate aninput circuit once power is removed. In addition, once the circuit has beenisolated and power restored, the input loop current can be measured in2-wire transmitter applications.

The fusible AIFMs have five terminals per input channel (except theAIFM16-F-3 which has three terminals per channel) to wire the inputmodule connections, device shield, and power connections for 2-, 3-, and4-wire transmitters. The shield terminals are internally bussed together andalso tied to the D-shell housing to connect with the cable shield. There aretwo separate power busses (from 4 to 16 terminals depending on theAIFM) that can be used for +V and DC COM connections and/or ModuleCommon. The extra terminals and internal connections eliminateadditional terminal blocks and jumpers — reducing spare parts inventory,saving panel space, and simplifying installation.

All of the fusible AIFMs have on-board DIP switches to easily connectunused inputs to module common — reducing wiring on the field-side.You no longer need extra jumper wires or comb-style jumpers to properlyterminate unused inputs as recommended on many 1746 and 1771 analoginput modules. Inputs are jumpered via DIP switch on a per channel basis.


The 1492-AIFM4I-F-5 and 1492-AIFM4C-F-5 both have test point loopson either side of the fuse clips for easier access and connection ofmetering equipment. Metering equipment can also be attached to the fuseclips on other AIFMs for measuring input loop current.

Below are examples of the field-side connections for 2- and 4-wiretransmitters available on the fusible AIFMs.

2-Wire Transmitter

4-Wire Transmitter

AIFM

Pre-wired Cable

AIFM

Pre-wired Cable

Analog Input Module

Analog Input Module

Power Supply

Transmitter

+V

V1

1+

SHIELD

1–

VCOM

Channel 1+

Channel 1–

Power Supply

Transmitter

+V

V1

1+

1–

SHIELD

VCOM

Channel 1+

Channel 1–

Fusible Modules, continued


Accessories

Cat. No. 1492-IFMFH1Fuse Holder

Cat. No. 1492-SJM5-10Insulated Side Jumper

Cat. No. 1492-ISOSW-1Isolation Switch Plug

Replacement Fuse Holders

The 1492-IFMFH1 fuse holders accommodate a 5 x 20mm fuse or the1492-ISOSW-1 isolation switch plug and reside in the AIFM under normaloperation. All of the fusible 1492 AIFMs come standard with the fuseholders (10 fuse holders with the 1492-AIFM4C-F-5, -AIFM4I-F-5, and-AIFM8-F-5; 20 fuse holders with the 1492-AIFM16-F-3, and-AIFM16-F-5). Replacement fuse holders are available in packages of 20.

Isolation Switch Plugs

The 1492-ISOSW-1 is an isolation switch or “dummy fuse” in a 5 x 20mmfuse form factor. The isolation switch plugs will fit into the 1492-IFMFH1fuse holders. If fusing is not desired on a fusible AIFM, the1492-ISOSW-1 can be used to provide feed-through functionality undernormal operation and isolation switch functionality once power has beenremoved from the circuit. The isolation switch can then be opened formaintenance and troubleshooting. Metering equipment can also be insertedinto a 2-wire transmitter circuit to measure input loop current. The1492-ISOSW-1 isolation switch plugs are available in packages of 4.

Insulated Side Jumpers

The 1492-SJM5-10 is a 10-pole “comb-style” insulated side jumper. Aside cutter can be used to cut the 10-pole jumper into smaller poleassemblies. The jumper fits the field-side terminal spacings on all of the1492-AIFMs and is a convenient means of connecting unused inputstogether on the feed-through AIFMs. The 1492-SJM5-10 insulated sidejumpers are available in packages of 10.


To order the proper pre-wired cable and AIFM, you need to know:

1. The catalog number(s) of the analog I/O modules.

2. The desired cable length (0.5m, 1.0m, 2.5m, 5.0m or custom length).

3. If fusing for inputs is needed.

4. If additional terminals for field devices are needed.

Refer to the pre-wired cable and AIFM selection table on page 10.For more information, refer to the technical section on pre-wired cables onpage 11, and to the technical section on AIFMs on page 15.

AIFM Catalog NumberExplanation

Important: The following AIFM catalog number breakdown is for explanationpurposes only. It is not a product configurator. All combinations of fieldsare not valid product catalog numbers. First, select the desired AIFM usingthe steps in How to Order Pre-wired Cables and AIFMs. Then use thisbreakdown for verification and explanation only.

BulletinNumber

Product TypeIFM Digital Interface Module

AIFM Analog Interface Module Input Fuse Clips &Blown Fuse Indication

Blank No Fuse Clips

F 5 x 20mm Fuse Clips with 24V DCBlown Fuse Indicators

Number of Analog I/O Channels4 Four Channels: Input, Output, or 2-In/2-Out

Combination

4C Four Channels: 2-In/2-Out Combination

4I Four Channels: Input

6S Six Channels: Isolated Input or Output

6TC Six Channels: Thermocouple Input

8 Eight Channels: Input or Output

16 Sixteen Channels: Input

Number ofField-Side Terminals

3 Three per I/O Channel

5 Five per Input Channel

How to Order Pre-wiredCables and AIFMs


The following cable catalog number explanation may be used as a productconfigurator. All combinations of fields indicated produce valid productcatalog numbers.

Cable TypeA, B, C, D, L Pre-wired cables for 1746

Analog & RTD I/O Modules ➊

E, F, G, H, J Pre-wired cables for 1771Analog & RTD I/O Modules ➊

X, Y, Z Pre-wired cables for 1756Analog, RTD, & ThermocoupleI/O Modules ➊

➊ Refer to cable selection table on page 10 for proper AIFM and I/O module compatibility.

BulletinNumber

Product TypeACABLE Analog Interface Cable

Standard Cable Length005 0.5 meter (1.64 feet)

010 1.0 meter (3.28 feet)

025 2.5 meter (8.20 feet)

050 5.0 meter (16.40 feet)

Custom Cable Length001–020 0.1–2.0 meter (0.328–6.56 feet)

0.1 meter (0.328 feet) increments

020–100 2.0–10.0 meter (6.56–32.8 feet)0.5 meter (1.64 feet) increments

100–990 10.0–99.0 meter (32.8–374.72 feet)1.0 meter (3.28 feet) increments

To use:

• Locate your I/O Module in one of the shaded areas.

• Follow down the selected column to the cable selection code that indi-cates the compatible AIFMs. If the space is blank, the I/O Module andAIFM are not recommended for use together.

• Select the catalog number of the desired AIFM. Refer to the page num-ber indicated for technical information on the AIFM.

Note: To configure a cable catalog number, order 1492-ACABLE➊➋ .

➊ Cables are available in 0.5, 1.0, 2.5, and 5.0m lengths. Insert the cablelength code into the catalog number. Cable length codes are as follows:“005” = 0.5m, “010” = 1.0m, “025” = 2.5m, and “050” = 5.0m.

All 1492 cables are also available in custom lengths. Contact yourlocal Allen-Bradley distributor or sales office for availability.

Custom Cable Lengths

Length Increment Size Cable Length Codes Examples0.1m–2.0m 0.1m 001–020 1492-ACABLE015A

2.0m–10.0m 0.5m 020–100 1492-ACABLE075B

10.0m–99.0m 1.0m 100–990 1492-ACABLE150F

Note: Some I/O modules may have recommended maximum cable lengths.Refer to the appropriate I/O module Product Data Publication for moreinformation.

➋ Insert cable selection code (see table on next page).Example: 1492-ACABLE005A is a 0.5m cable for the 1746-NI4 inputmodule.

Cable Catalog NumberExplanation

Pre-wired Cable and AIFMSelection Table for AnalogI/O Modules


Pre-wired Cable and AIFMSelection Table for AnalogI/O Modules, continued

I/O Module Catalog Number

Typeof

IFM DescriptionCat. No.

1492- Page 1746

-FIO

4I

1746

-FIO

4V

1746

-NI4

1746

-NI8

1746

-NIO

4I

1746

-NIO

4V

1746

-NO

4I

1746

-NO

4V

1746

-NR

4

1771

-IFE

(Diff

eren

tial)

1771

-IFE

(Sin

gle-

Ende

d)

1771

-IL

1771

-IR

1771

-OFE

1

1771

-OFE

2

1771

-OFE

3

1756

-IF6I

(Cur

rent

)

1756

-IF6I

(Vol

tage

)

1756

-IR6I

1756

-IT6I

1756

-OF6

CI

1756

-OF6

VI

ough

4-Channel with 3terminals per channeland selectable 250Ωcurrent limit resistorsfor 1771-OFE.

AIFM4-3 16 L L A L L B B G G G

Feed

thro

6-Channel isolatedwith 3–4 terminals perchannel.

AIFM6S-3 17 D J X Y Z Y Y

8-Channel with 3terminals per channel. AIFM8-3 18 C E F H

Ther

moc

oupl

e

6-Channel with 3terminals per channel. AIFM6TC-3 19 Y

2-Channel with 24VBlown Fuse Indicators,test points, 5 terminalsper input, and 3terminals per output.

AIFM4C-F-5 20 L L L L

4-Channel with 24VBlown Fuse Indicators,test points, and 5terminals per input.

AIFM4I-F-5 21 A

Fusi

ble 8-Channel with 24V

Blown Fuse Indicatorsand 5 terminals perinput.

AIFM8-F-5 22 C E

16-Channel with 24VBlown Fuse Indicatorsand 3 terminals perinput.

AIFM16-F-3 23 F

16-Channel with 24VBlown Fuse Indicatorsand 5 terminals perinput.

AIFM16-F-5 24 F

All channels in 1492-ACABLE_ _ _X are configured for current mode. For each voltage channel, a jumper wire must be removed. All channels in 1492-ACABLE_ _ _Y are configured for voltage mode. For each current channel, a user-supplied jumper wire must be

installed. All channels in 1492-ACABLE_ _ _Y are configured for 0–550 ohm loads. For each channel with 551–1000 ohm load, a wire must be

moved to a different terminal.


Bulletin 1492 Pre-wired Cables are designed to minimize control wiring ina panel. When used with an AIFM, the cables replace the point-to-pointwiring between Allen-Bradley programmable controller I/O modules andindividual terminal blocks. The pre-wired cables have a 1746 or 1756Removable Terminal Block or 1771 Wiring Arm on one end and a D-Shellconnector on the other to connect to the AIFM. The broad offering ofpre-wired cables supports over 20 different SLC 500, ControlLogix, andPLC analog, RTD and thermocouple I/O modules.

Refer to the Selection Table on page 10 for proper I/O module, AIFM, andpre-wired cable coordination.

Analog Pre-wired Cable Specifications

Cat. No. andLength ➊ I/O Module Connector

AIFMConnector

GeneralDescription ➋

InsulationRating

ConductorSize

Nominal OuterDiameter

1492-ACABLE➊ A 1746-RT28 12-Position Removable Terminal Block 15-pin D-Shell 5 Twisted Pairs 300V 80C #22 AWG .293 in. (7.44mm)

1492-ACABLE➊ B1746-RT26 2-Position and 1746-RT27 8-PositionRemovable Terminal Block 15-pin D-Shell 5 Twisted Pairs 300V 80C #22 AWG .293 in. (7.44mm)

1492-ACABLE➊ C 1746-RT25G Green Removable Terminal Block 25-pin D-Shell 9 Twisted Pairs ➌ 300V 80C #24 AWG .267 in. (6.78mm)1492-ACABLE➊ D 1746-RT25G Green Removable Terminal Block 25-pin D-Shell 20 Conductors ➍ 300V 80C #22 AWG .332 in. (8.43mm)1492-ACABLE➊ E 1771-WG (21 terminal) Wiring Arm 25-pin D-Shell 9 Twisted Pairs 300V 80C #24 AWG .267 in. (6.78mm)1492-ACABLE➊ F 1771-WG (21 terminal) Wiring Arm 25-pin D-Shell 20 Conductors 300V 80C #22 AWG .332 in. (8.43mm)1492-ACABLE➊ G 1771-WC (10 terminal) Wiring Arm 15-pin D-Shell 5 Twisted Pairs ➌ 300V 80C #22 AWG .293 in. (7.44mm)1492-ACABLE➊ H 1771-WF (18 terminal) Wiring Arm 25-pin D-Shell 9 Twisted Pairs ➌ 300V 80C #24 AWG .267 in. (6.78mm)1492-ACABLE➊ J 1771-WF (18 terminal) Wiring Arm 25-pin D-Shell 20 Conductors ➎ 300V 80C #22 AWG .332 in. (8.43mm)1492-ACABLE➊ L 1746-RT28 12-Position Removable Terminal Block 15-pin D-Shell 5 Twisted Pairs ➏ 300V 80C #22 AWG .293 in. (7.44mm)1492-ACABLE➊ X 1756-TBNH 20-Position Removable Terminal Block 25-pin D-Shell 9 Twisted Pairs ➐ 300V 80C #24 AWG .267 in. (6.78mm)1492-ACABLE➊ Y 1756-TBNH 20-Position Removable Terminal Block 25-pin D-Shell 9 Twisted Pairs ➑ 300V 80C #24 AWG .267 in. (6.78mm)1492-ACABLE➊ Z 1756-TBNH 20-Position Removable Terminal Block 25-pin D-Shell 20 Conductors ➎ 300V 80C #22 AWG .332 in. (8.43mm)

➊ Cables are available in lengths of 0.5m, 1.0m, 2.5m and 5.0m. To order, insert the desired cable length code into the catalog number(“005” = 0.5m, “010” = 1.0m, “025” = 2.5m, and “050” = 5.0m). Example: Cat. No. 1492-ACABLE005A is for a 0.5m cable forthe 1746-NI4 I/O Module. See also Custom Cable Lengths table on page 9.

➋ All pre-wired analog cables have an overall shield. On 1492-ACABLE➊ C and 1492-ACABLE➊ D, the drain wire is connected tothe shield terminal on the I/O module connector. All other 1492-ACABLEs have a ring lug on the 7.87″ (200mm) exposed drainwire at the I/O module end of the cable.

➌ 1 pair not wired to I/O module connector.➍ 7 conductors not wired to I/O module connector; 1 additional conductor not used.➎ 1 conductor not wired to I/O module connector; 1 additional conductor not used.➏ 1 pair not used.➐ 1 pair not wired to I/O module connector; 2 additional pairs not used.➑ 2 pairs not used.

0.7″17mm

1.6″39mm

2.3″58mm

2.9″73mm

1.8″44mm

1.6″39mm

0.7″17mm

2.4″60mm

D-Shell Connector Dimensions

15-Pin D-Shell 25-Pin D-Shell

Cable Technical Section


The following diagrams indicate how the analog pre-wired cables are“pinned out” on both ends. The description listed first is the wire color ofthe conductor connected to the screw terminal on the respective WiringArm or Removable Terminal Block. The number that follows inparentheses is the corresponding pin number in the D-Shell connector onthe other end.

For example:

No Connection

Twisted Pair Jumper Wire

Individual Conductor

Base Color Stripe Color

1492-ACABLE_ _ _A

➊ Twisted pair.

1492-ACABLE_ _ _C

1492-ACABLE_ _ _L

1492-ACABLE_ _ _G

1492-ACABLE_ _ _B

1492-ACABLE_ _ _D

Blue (24)

Black (23)

White/Green (22)

White/Red (19)

NC

Red (8)

NCBlack (15)

White (14)

Yellow (2) ➊Black (13)

Green (12)

NCBlack (11)

Blue (10)

Black (1) ➊Black (9)

Yellow (2)Black (1)

White (14)Black (13)

Red (8)Black (15)

Blue (10)Black (9)

Green (12)Black (11)

Red (8)

Black (15)

White (14)Black (13)

NC

NC

Green (11)Black (2)

NC

NCBlue (9)Black (1)

Red (3)Black (2)

NC

White (1)Black (14)

Green (15)Black (16)

Blue (17)Black (18)

Yellow (12)Black (13)

Brown (25)Black (24)

Orange (23)Black (22)

Red (20)White (21)

Drain

White (14)

Black (13)

Red (8)

Black (15)

Blue (10)

Black (9)

Green (12)

Black (11)

NC

NC

012

345

678

91011

012

345

678

91011

01

01

23

45

67

A

0

1

2

3

4

5

6

7

B

D-Shell Connector Pin Number

White/Violet (25)

NC

Blue (13)

White/Orange (21)

Orange (9)

Green (12)

White/Yellow (22)

NC

NC

White/Blue (24)

White/Green (23)

Yellow (11)

NC

White/Red (19)

White/Brown (18)

Red (6)

Drain

NC

Pre-wired Cable Pinouts


Pre-wired Cable Pinouts,continued

Black (18)

1492-ACABLE_ _ _E

1492-ACABLE_ _ _J

1492-ACABLE_ _ _F

1492-ACABLE_ _ _X 1492-ACABLE_ _ _Z1492-ACABLE_ _ _Y

Red (3)

Black (2)

NC

White (1)

Black (14)

Green (15)

Black (16)

Blue (17)

Black (18)

Yellow (12)

Black (13)

Brown (25)

Black (24)

Orange (23)

Black (22)

Red (20)

White (21)

NC

NC

Red (6)

Green (19)

1492-ACABLE_ _ _H

Red (3)

Brown (2)

Black (1)

White (14)

Orange (4)

White/Black (15)

White/Brown (16)

White/Red (17)

White/Orange (18)

Blue (10)

Violet (12)

Gray (13)

White/Black/Brown (25)

White/Gray (24)

Green (8)

White/Violet (23)

White/Blue (22)

White/Yellow (20)

White/Green (21)

Yellow (6)

NC

Blue (24)

Black (23)

Yellow (19)

Black (18)

NC

Orange (15)

Black (14)

Red (13)

Black (25)

White (22)

Black (21)

NC

Green (17)

Black (16)

Blue (24)

NC

Black (23)

Yellow (19)

Brown (6)Black (20)

Orange (15)

NC

Black (14)

Red (13)

NC

Black (25)

White (22)

NC

Black (21)

Green (17)

NC

Black (16)

NC

White/Blue (24)

Yellow (11)

White/Green (23)

White/Red (19)

Red (6)

White/Brown (18)

NC

Gray (15)

Black (2)

Violet (14)

Blue (13)

Green (12)

White/Violet (25)

White/Yellow (22)

Orange (9)

White/Orange (21)

NC

White/Black (17)

Brown (4)

White (16)

NCNC

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

18

16

14

12

10

8

6

4

2

18

16

14

12

10

8

6

4

2

2 1

20 19

2 1

20 19

2 1

20 19

Red (3)Black (2)White (1)Black (14)Green (15)Black (16)Blue (17)Black (18)

Yellow (12)Black (13)Brown (25)Black (24)Orange (23)Black (22)Red (20)White (21)

White/Violet (25)Green (12)Blue (13)White/Green (23)Yellow (11)White/Blue (24)White/Orange (21)Orange (9)White/Yellow (22)White/Brown (18)Red (6)White/Red (19)White (16)Brown (4)White/Black (17)Violet (14)Black (2)Gray (15)


AIFM Technical Section

AIFM Cat. No.Page No. for Specifications,Application Notes & Pinout

Page No. forAdhesive Label Card

1492-AIFM4-3 15 27

1492-AIFM6S-3 16 29

1492-AIFM8-3 17 30

1492-AIFM6TC-3 18 29

1492-AIFM4C-F-5 19 28

1492-AIFM4I-F-5 20 28

1492-AIFM8-F-5 21 31

1492-AIFM16-F-3 22 31

1492-AIFM16-F-5 23 32

For all AIFM dimensions, see page 24.For general Adhesive Label Card information, see page 26.For Field-Side Wiring Diagrams per I/O module, see pages 33–56.

Symbology Used Throughout Pinout and Wiring Sections= 1492-AIFM Field-Side Terminal ➊

= 1492 Pre-wired Cable

= I/O Module Connection

= Fuse and Blown Fuse Indicator

= 1-Pole DIP Switch

= 2-Pole DIP Switch

= 1492-AIFM and Cable Connection (D-shell pin)

= Test Point

➊ Field-Side Terminal Identification Convention:

B1 B2 B3 B4 B5 . . .

A1 A2 A3 A4 A5 . . .

C1 C2 C3 C4 C5 . . .

B1 B2 B3 B4 B5 . . .

A1 A2 A3 A4 A5 . . .


1492-AIFM4-3Specifications

Approvals UL Component Recognized (File E113724 Guide NRAQ2)UL Recognized per Canadian Safety Standards (cUR)

(File E113724 Guide NRAQ2)CE Approved

Voltage Rating 0–132V AC/DC

Maximum Peak Voltage ➊ 600Vp

Maximum Current (per Circuit) 2A

Maximum Current (per Module) 12A

Indicator Circuit Current (Nominal) –

No. of Terminals per Shield Common 4

Wire Range (Rated Cross Section) ➋ #22–#12 AWG (0.2–4mm2)

Wire Strip Length 0.32″ (8mm)

Recommended Tightening Torque 3.5–4.5 lb.-in. (0.38–0.50 Nm)

Operating Temperature Range 0C to +60C

➊ For transients >600Vp, use a UL recognized suppression device rated at 2.5kVwithstand.

➋ Maximum number of the same gauge stranded copper conductors allowed perwire funnel:

AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1

Application Notes1. Compatibility – To ensure proper operation with the

I/O module, do not exceed the voltage and currentratings of the AIFM.

2. Wiring – Refer to the Label Section on page 26 andthe Field-Side Wiring Diagrams on page 33.

3. DIP Switches – Selectable resistors are available tocurrent limit the 1771-OFE2 and -OFE3 output cir-cuits. By opening the switch (off or down position),250Ω series impedance is inserted into the outputcircuit. Default switch position is on/closed/no seriesimpedance. Do not exceed maximum loop impedanceof output module (1200Ω for -OFE2; 450Ω for-OFE3).

4. Test Points – With optional 250Ω series impedancein output circuit (see DIP Switches), test points canbe used to measure loop voltage/current. Refer to thePinout for test point circuit location.

5. Shield Terminals – Four field-side terminals arejumpered together on the AIFM and internally con-nected to the D-shell housing.

6. Dimensions – See page 24.

PinoutA32B3

A7B7

A1

A2

A5

A6

B1

B2

B5

B6

A4A8B4B8

1

8

15

14

13

12

11

10

9

TP1 TP2

TP3 TP4

TP5 TP6

TP7 TP8

D-Shell Housing


1492-AIFM6S-3Specifications















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1




3. Shield Terminals – Six field-side terminals arejumpered together on the AIFM and internally con-nected to the D-shell housing.


Pinout

B113

A1

B2

B3

A3

B4

B5

A5

B6

B7

A7

B8

B9

A9

B10

B11

12

25

24

11

23

22

9

21

19

D-Shell Housing

A11

B12

A2A4

A6A8A10A12

6

18

17

4

16

15

2

14


1492-AIFM8-3Specifications















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1




3. Extra Terminals – Eight field-side terminals arejumpered together on the AIFM. For some I/O mod-ules, the terminals are also internally connected to“module common” through the pre-wired cable. Re-fer to the AIFM and ACABLE pinouts.

4. Shield Terminals – Eight field-side terminals arejumpered together on the AIFM and internally con-nected to the D-shell housing.


Pinout

B13

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

B12

B13

B14

B15

B16

2

1

14

15

16

17

18

12

13

D-Shell Housing

A9A10A11A12A13A14A15A16

25

24

23

22

20

21

A1A2A3A4A5A6A7A8

468

10

19


1492-AIFM6TC-3Specifications















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1




3. Shield Terminals – Six field-side terminals arejumpered together on the AIFM and internally con-nected to the D-shell housing.

4. Cold Junction Compensation – This AIFM containson-board cold junction compensation through athermistor and isothermal bar mounted to the field-side terminals. Do NOT install the additional coldjunction sensor (provided with the 1756-IT6I thermo-couple input module) on the removable terminalblock of the pre-wired cable.


PinoutB113

B2

B3

B4

B5

B6

B7

B8

B9

B10

B11

B12

A7

A1

A3

A5

25

24

23

22

21

19

18

17

16

D-Shell Housing

15

14

6

20

12

11

A2A4A6A8A10A12

A9

A11

9

4

2

T


1492-AIFM4C-F-5Specifications



Voltage Rating 10–30V DC




Indicator Circuit Current (Nominal) 2mA








AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1




3. Fusing – Ten fuse holders are included with theAIFM. Fuses (5 x 20mm) are not included. Do notexceed 2A per input, 12A per AIFM.

4. Isolation – The fuse clips and blown fuse indicatorsare internally connected to one power source field-side terminal. All inputs must reference the samepower source.

5. DIP Switches – For ease of wiring, unused inputscan be jumpered to module common by closing theDIP switches (ON position). Default switch positionis OPEN/OFF/NOT jumpered together.

6. Test Points – When using a 2-wire transmitter, testpoints can be used to measure input loop current.Refer to the Pinout for test point circuit location.

7. Extra Terminals – Four field-side terminals are in-ternally jumpered on the AIFM. They can be used forpower source common connections.

8. Shield Terminals – Four field-side terminals arejumpered together on AIFM and internally connectedto the D-shell housing.


Pinout

B18

A8

B2

A5

B3

B4

B5

B6

B7

B8

B9

B10

B11

A2

A1

B12

15

14

13

12

11

2

10

9

1

TP1 TP2

TP3 TP4

D-Shell Housing

A12

A9

....

....


1492-AIFM4I-F-5Specifications















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1







6. Test Points – When using a 2-wire transmitter, testpoints can be used to measure input loop current.Refer to the Pinout for test point circuit location.

7. Extra Terminals – Four field-side terminals are in-ternally jumpered on the AIFM. They can be used forpower source common connections.

8. Shield Terminals – Four field-side terminals arejumpered together on the AIFM and internally con-nected to the D-shell housing.


Pinout

B18

A8

B2

A5

B3

B4

B7

B5

B6

B8

B9

B10

B11

A4

A1

B12

15

14

13

2

12

11

10

9

1

TP1 TP2

TP7 TP8

D-Shell Housing

A12

A9

.....

.....

.....


1492-AIFM8-F-5Specifications















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1






5. DIP Switches – For ease of wiring on the 1771-IFE,unused inputs can be jumpered to module commonby closing the DIP switches (ON position). Defaultswitch position is OPEN/OFF/NOT jumperedtogether.

6. Extra Terminals – Nine field-side terminals are in-ternally jumpered on the AIFM. They can be used forpower source common connections.

7. Shield Terminals – Eighteen field-side terminals arejumpered together on the AIFM and internallyconnected to the D-shell housing.


PinoutC1

C16

C2

C15

C3

C4C5

C6C7

C8C9

C10C11

C13C12

C14

D-Shell Housing

B2

B1

B9

B10

B18

A1

A18

3

21

1415

1617

1812

1325

2423

2220

21

6

19

.....

.....

.....

















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1




3. Fusing – Twenty fuse holders are included with theAIFM. Fuses (5 x 20mm) are not included. Do notexceed 2A per input, 12A per AIFM.



6. Shield Terminals – Eighteen field-side terminals arejumpered together on the AIFM and internallyconnected to the D-shell housing.


PinoutB2

B16

B3

B15

B4

B5

B6

B7

B8

B9

B10

B11

B13

B12

B14

D-Shell Housing

B18

B17

B1

C1

C16

A1

A18

3

2

1

14

15

16

17

18

12

13

25

24

23

22

20

21

468

10

19 .....

.....

















AWG #22 #20 #18 #16 #14 #12

No. of Wires 3 3 3 2 1 1




3. Fusing – Twenty fuse holders are included with theAIFM. Fuses (5 x 20mm) are not included. Do notexceed 2A per input, 12A per AIFM.

4. Isolation – The fuse clips and blown fuse indicatorsare internally connected to two separate power sourcefield-side terminals. All inputs within a group mustreference the same power source.


6. Extra Terminals – Sixteen field-side terminals(C9–C16 on TB1 and TB2) are internally jumperedon the AIFM and connected to module common.Eighteen field-side terminals (B10–B18 on TB1 andTB2) are internally jumpered on the AIFM and canbe used for power source common connections.There are two field-side terminals (A17 and A18 onTB1) which can be externally jumpered to connectthe two groups of field-side terminals.

7. Shield Terminals – Sixteen field-side terminals arejumpered together on the AIFM and internally con-nected to the D-shell housing.


TB1

TB2

Pinout

C1

B10

C2

B9

C3

C4

C5

C6

C7

C8

C9

C16

B1

A17

B2

D-Shell Housing

A18B18

A1

A8

3

2

1

14

15

16

17

18

C1

B10

C2

B9

C3

C4

C5

C6

C7

C8

C9

C16

B1

B2

B18

A1

12

13

25

24

23

22

20

21

TB1 TB2

468

10

19 .....

.....

...

...

........

...

A8

...


Dimensions

3.27″(83mm)

2.74″(69.5mm)

2.19″(55.5mm)

1.67″(42.5mm)

3.27″(83mm)

2.74″(69.5mm)

2.19″(55.5mm)

1.67″(42.5mm)

3.27″(83mm)

2.74″(69.5mm)2.19″

(55.5mm)1.67″

(42.5mm)

3.27″(83mm)

2.74″(69.5mm)2.19″

(55.5mm)1.67″

(42.5mm)

3.27″(83mm)

2.74″(69.5mm)

2.19″(55.5mm)

1.67″(42.5mm)

1492-AIFM4-3

1492-AIFM6S-31492-AIFM6TC-3

1492-AIFM4C-F-51492-AIFM4I-F-5

1492-AIFM8-3

1492-AIFM8-F-51492-AIFM16-F-3

1492-AIFM16-F-5

2.36″(60mm)

3.15″(80mm)

3.15″(80mm)

4.33″(110mm)

4.72″(120mm)

8.27″(210mm)

3.27″(83mm)

2.74″(69.5mm)2.19″

(55.5mm)1.67″

(42.5mm)


All Bulletin 1492 AIFMs come with an adhesive label card. The label cardprovides the field-side connection descriptions for the programmablecontroller I/O module. The label cards list all of the compatibleI/O modules and their respective wiring descriptions. Depending on theI/O module that is used, the label strip(s) are simply peeled from the labelcard and applied to the field-side terminals on the AIFM. The label stripsbasically copy the wiring descriptions from the I/O module in the chassisdown to the AIFM terminals on the DIN rail.

Fusible AIFMs come with the fuse clips/blown fuse indicatorspre-numbered on the AIFM circuit board. Conversion label strip(s) areprovided on the label card to change the numbering on the AIFM, ifdesired. The conversion labels would be placed directly on the circuitboard of the AIFM. For example, if the fuse clips and blown fuseindicators were pre-numbered “0–3”, a conversion label for “1–4” isprovided.

For AIFMs with extra terminals, pre-printed labels are provided to identifythe shield connections (“SH” or “SHIELD”), module commons(“MODULE COM”, “COM”, or “C”), and power source commons (“+V”,“–V”, “COM”, and “VCOM”).

In addition, if generic numbering of the field-side terminals is desired,“Numeric” labels are provided. Examples: “1–20”, “1–52”, and evens andodds. For write-on identification, the label cards contain blank label strips(for field-side terminals) and rectangular boxes (for the large groupmarking area on each AIFM).

The six different labels are shown actual size on pages 26–31. Thisinformation is helpful for determining field-side wiring layouts prior toinstallation.

AIFM Cat. No. Adhesive Label Card Page No.

1492-AIFM4-3 26

1492-AIFM4C-F-5, -AIFM4I-F-5 27

1492-AIFM6S-3, -AIFM6TC-3 28

1492-AIFM8-3 29

1492-AIFM8-F-5, -AIFM16-F-3 30

1492-AIFM16-F-5 31

An example of how the labels are applied is shown below:

Adhesive Label Cards


Adhesive Label Card forCatalog Number 1492-AIFM4-3

I/O CAT. NO. MODULE LABEL LEVEL

1746-NI4 2+ 2- C SH 3+ 3- C SH UPPER

0+ 0- C SH 1+ 1- C SH LOWER

1746-NIO4I, O/0 C SH O/1 C SH UPPER1746-NIO4I,-NIO4V, -FIO4I,-FIO4V 0+ 0- C SH 1+ 1- C SH LOWER

1746-NO4I, 2 C +V SH 3 C -V SH UPPER-NO4V,

0 C +V SH 1 C -V SH LOWER

2 C SH 3 C SH UPPER

0 C SH 1 C SH LOWER

1771-OFE 3+ 3- SH 4+ 4- SH UPPER

1+ 1- SH 2+ 2- SH LOWER

NUMERIC 1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16

1 3 5 7 9 11 13 15

2 4 6 8 10 12 14 16

45006-034-01 (A)


Adhesive Label Card for CatalogNumbers 1492-AIFM4C-F-5 and1492-AIFM4I-F-5

I/0 CAT. NO. MODULE LABEL LEVEL

1746-NI4 0+ 0- 1+ 1- 2+ 2- 3+ 3- +V VCOM UPPER

V0 V1 V2 V3 VCOM SHIELD LOWER

1746-NIO4I, 0+ 0- 1+ 1- O/0 C O/1 C +V VCOM UPPER1746-NIO4I,-NIO4V, -FIO4I,-FIO4V V0 V1 VCOM SHIELD LOWER

LED 1 2 3 4

NUMERIC 1 2 3 4 5 6 7 8 9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

1 3 5 7 9 11 13 15 17 19 21 23

2 4 6 8 10 12 14 16 18 20 22 24

45006-021-02 (B)


Adhesive Label Card forCatalog Numbers 1492-AIFM6S-3and 1492-AIFM6TC-3


1756-IT6I, 0 R0 1 R1 2 R2 3 R3 4 R4 5 R5 UPPER1756-IT6I,-OF6CI, -OF6VI,-IF61 SH SH SH SH SH SH LOWER

1756-IR6I A0 R/C0 A1 R/C1 A2 R/C2 A3 R/C3 A4 R/C4 A5 R/C5 UPPER

B0 SH B1 SH B2 SH B3 SH B4 SH B5 SH LOWER

1746-NR4 I0 S0 I1 S1 I2 S2 I3 S3 UPPER

R0 SH R1 SH R2 SH R3 SH LOWER

1771-IR A1 C1 A2 C2 A3 C3 A4 C4 A5 C5 A6 C6 UPPER

B1 SH B2 SH B3 SH B4 SH B5 SH B6 SH LOWER

NUMERIC 1 2 3 4 5 6 7 8 9 10 11 12

13 14 15 16 17 18 19 20 21 22 23 24

1 3 5 7 9 11 13 15 17 19 21 23

2 4 6 8 10 12 14 16 18 20 22 24

45006-021-01 (B)


Adhesive Label Card forCatalog Number 1492-AIFM8-3


1771-IFE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UPPERSINGLE ENDED

SHIELD MODULE COM LOWER

1771-IFE 1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- 8+ 8- UPPER DIFFERENTIAL

SHIELD MODULE COM LOWER

1771-IL 1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- 8+ 8- UPPER

SHIELD COM LOWER

1746-NI8 0+ 0- 1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- UPPER

SHIELD COM LOWER

NUMERIC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 UPPER

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 LOWER

1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 UPPER

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 LOWER

45006-019-01 (A)


Adhesive Label Card for CatalogNumbers 1492-AIFM16-F-3 and1492-AIFM8-F-5

I/O CAT. NO. MODULE LABEL LEVEL

1771-IFE V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16 Upper

1771-IFE SINGLE ENDED +V 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 COM Middle

SHIELD Lower

1771-IFE1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- 8+ 8- Upper

1771-IFEDIFFERENTIAL +V V1 V2 V3 V4 V5 V6 V7 V8 V COM Middle

SHIELD Lower

0+ 0- 1+ 1- 2+ 2- 3+ 3- 4+ 4- 5+ 5- 6+ 6- 7+ 7- Upper1746-NI8

+V V0 V1 V2 V3 V4 V5 V6 V7 V COM Middle

SHIELD Lower

LED LABEL 0 1 2 3 4 5 6 7

NUMERIC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

44006-274-01 (D)


Adhesive Label Card for CatalogNumber 1492-AIFM16-F-5


1771-IFE 1 2 3 4 5 6 7 8 MODULE COM UPPER LFSINGLE ENDED

+V V1 V2 V3 V4 V5 V6 V7 V8 V COM MIDDLE LF

SHIELD 1J-1 1J-2 LOWER LF

9 10 11 12 13 14 15 16 MODULE COM UPPER RT

+V V9 V10 V11 V12 V13 V14 V15 V16 V COM MIDDLE RT

SHIELD LOWER RT

NUMERIC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 TB1

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 TB2

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86

87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104

17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50

51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68

LED LABEL 0 1 2 3 4 5 6 7 LEFT

8 9 10 11 12 13 14 15 RIGHT

45006-018-01 (A)


Field-Side Wiring DiagramsI/O Module Cat. No. AIFM Cat. No. Page No.

1746-FIO4I, -FIO4V, -NIO4I, -NIO4V 1492-AIFM4-3 33

1746-FIO4I, -FIO4V, -NIO4I, -NIO4V 1492-AIFM4C-F-5 35

1746-NI4 1492-AIFM4-3 37

1746-NI4 1492-AIFM4I-F-5 38

1746-NI8 1492-AIFM8-3 39

1746-NI8 1492-AIFM8-F-5 40

1746-NO4I, -NO4V 1492-AIFM4-3 41

1746-NR4 1492-AIFM6S-3 42

1756-IF6I 1492-AIFM6S-3 43

1756-IR6I 1492-AIFM6S-3 45

1756-IT6I 1492-AIFM6TC-3 46

1756-OF6CI, -OF6VI 1492-AIFM6S-3 47

1771-IFE Differential 1492-AIFM8-3 48

1771-IFE Differential 1492-AIFM8-F-5 49

1771-IFE Single-ended 1492-AIFM8-3 50

1771-IFE Single-ended 1492-AIFM16-F-3 51

1771-IFE Single-ended 1492-AIFM16-F-5 52

1771-IL 1492-AIFM8-3 53

1771-IR 1492-AIFM6S-3 54

1771-OFE1, -OFE2, -OFE3 1492-AIFM4-3 55

Symbology Used Throughout Pinout and Wiring Sections= 1492-AIFM Field-Side Terminal ➊

= 1492 Pre-wired Cable

= I/O Module Connection

= Fuse and Blown Fuse Indicator

= 1-Pole DIP Switch

= 2-Pole DIP Switch

= 1492-AIFM and Cable Connection (D-shell pin)

= Test Point

➊ Field-Side Terminal Identification Convention:

B1 B2 B3 B4 B5 . . .

A1 A2 A3 A4 A5 . . .

C1 C2 C3 C4 C5 . . .

B1 B2 B3 B4 B5 . . .

A1 A2 A3 A4 A5 . . .


Field-Side Wiring Diagrams,continued

1746-FIO4I, -FIO4V, -NIO4I, -NIO4V Inputswith 1492-AIFM4-3

Single-Ended Signal Source or 2-Wire Transmitter

3-Wire Transmitter

Differential Signal Source or 4-Wire Transmitter

Unused Inputs

➊ Shield terminals on AIFM are connected to pre-wired cable shield through D-shell housing.

➋ Optional: 1492-SJM5-10.

1492-AIFM4-3

1492-ACABLE_ _ _L

1746-FIO4I, -FIO4V,-NIO4I, -NIO4V

Power Supply

Transmitter 0+

SH

0–

C

0+

SH

0–

C

Power Supply

Transmitter

1492-AIFM4-3

1492-ACABLE_ _ _L


IN 0+

IN 0+

IN 0–

IN 0–

1492-AIFM4-3

1492-ACABLE_ _ _L


1492-AIFM4-3

1492-ACABLE_ _ _L



SH

C

0+

SH

0–

C

IN 0+

IN 0–

IN 0+

IN 0–

1492-AIFM4-3

O/0 C SH O/1 C SH

C SH 1+ 1– C SH

➋

0+

0–

0+ 0–

➊

➊

➊

➊



1746-FIO4I, -FIO4V, -NIO4I, -NIO4V Outputswith 1492-AIFM4-3

Outputs

O/0

1492-AIFM4-3

1492-AIFM4-3

1492-ACABLE_ _ _L


LOAD

OUT 0

ANL COMC

SH

O/0

C SH O/1 C SH

C SH 1+ 1– C SH

Unused Outputs – Do not jumper unused outputs

0+ 0–


➊



1746-FIO4I, -FIO4V, -NIO4I, -NIO4V Inputswith 1492-AIFM4C-F-5

O/0


3-Wire Transmitter


V1

1492-AIFM4C-F-5

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM4C-F-5

1492-ACABLE_ _ _L


IN 0+

IN 0–0–

VCOM

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM4C-F-5

1492-ACABLE_ _ _L


IN 0+

IN 0–0–

VCOM

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM4C-F-5

1492-ACABLE_ _ _L


IN 0+

IN 0–0–

VCOM

VCOM SHIELD

1+ 1– C O/1 C +V VCOM0+ 0–

V0


➊

➊

➊



1746-FIO4I, -FIO4V, -NIO4I, -NIO4V Outputswith 1492-AIFM4C-F-5

V1

Outputs

O/0

1492-AIFM4C-F-5VCOM SHIELD

1+ 1– C O/1 C +V VCOM

1492-AIFM4C-F-5

1492-ACABLE_ _ _L


LOAD

OUT 0

ANL COMC

SHIELD

O/0

V0


0+ 0–


➊



1746-NI4with 1492-AIFM4-3


3-Wire Transmitter


Unused Inputs


➋ Optional: 1492-SJM5-10.

1492-AIFM4-3

1492-ACABLE_ _ _A

1746-NI4

Power Supply

Transmitter 0+

SH

0–

C

0+

SH

0–

C

Power Supply

Transmitter1492-AIFM4-3

1492-ACABLE_ _ _A1746-NI4

IN 0+

IN 0+

IN 0–

IN 0–

1492-AIFM4-3

2+ C SH C SH

C SH 1+ 1– C SH

2– 3+ 3–

1492-AIFM4-3

1492-ACABLE_ _ _A

1746-NI4

1492-AIFM4-31492-ACABLE_ _ _A

1746-NI4


SH

C

0+

SH

0–

C

IN 0+

IN 0–

IN 0+

IN 0–

➊

0+

0–

0+ 0–

➋

➊

➊

➊



1746-NI4with 1492-AIFM4I-F-5


3-Wire Transmitter


V1 VCOM SHIELD

1+ 1– +V VCOM

V0

2+ 2– 3+ 3–

V2 V3

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM4I-F-5

1492-ACABLE_ _ _A1746-NI4

IN 0+

IN 0–0–

VCOM

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM4I-F-5

1492-ACABLE_ _ _A1746-NI4

IN 0+

IN 0–0–

VCOM

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM4I-F-5

1492-ACABLE_ _ _A1746-NI4

IN 0+

IN 0–0–

VCOM

1492-AIFM4I-F-5

0+ 0–


➊

➊

➊



1746-NI8with 1492-AIFM8-3


3-Wire Transmitter


0+

SHIELD COM

0– 1+ 1– 2+ 2– 3+ 3– 4+ 4– 5+ 5– 6+ 6– 7+ 7–

0+

SHIELDPower Supply


1492-ACABLE_ _ _C1746-NI8

Channel 0+

Channel 0–0–

COM

0+

SHIELDPower Supply


1492-ACABLE_ _ _C1746-NI8

Channel 0+

Channel 0–0–

COM

0+

SHIELD


1492-AIFM8-3

1492-ACABLE_ _ _C1746-NI8

Channel 0+

Channel 0–0–

COM

1492-AIFM8-3


➊

➊

➊



1746-NI8with 1492-AIFM8-F-5


3-Wire Transmitter


1492-AIFM8-F-5

SHIELD

VCOM+V V0 V1 V2 V3 V4 V5 V6 V7

0+ 0– 1+ 1– 2+ 2– 3+ 3– 4+ 4– 5+ 5– 6+ 6– 7+ 7–

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM8-F-5

1492-ACABLE_ _ _C1746-NI8

Channel 0+

Channel 0–0–

VCOM

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM8-F-5

1492-ACABLE_ _ _C1746-NI8

Channel 0+

Channel 0–0–

VCOM

+V

V0

0+

SHIELD

Power Supply

Transmitter

1492-AIFM8-F-5

1492-ACABLE_ _ _C1746-NI8

Channel 0+

Channel 0–0–

VCOM


➊

➊

➊



1746-NO4I, -NO4Vwith 1492-AIFM4-3

1746-NO4I, -NO4Vwithout External Power

With External Power

Without External Power


1746-NO4I, -NO4Vwith External Power

2 +V SH C –V SH

+V SH 1 C –V SHC

SH SH

SH 1 C SHC

C 3 3 C2 C

1492-AIFM4-3

1492-ACABLE_ _ _B

1746-NO4I, -NO4V

LOAD

OUT 0

ANL COMC

SH

0

+V

–V

ExternalPowerSupply

+24V DC

DC COM

1492-AIFM4-3

1492-ACABLE_ _ _B

1746-NO4I, -NO4V

LOAD

OUT 0

ANL COMC

SH

0

1492-AIFM4-3

0 0


➊

➊



1746-NR4with 1492-AIFM6S-3

2-Wire Potentiometer or RTD

3-Wire Potentiometer or RTD

4-Wire RTD

I0 S0 I1 S1 I2 S2 I3 S3

R0 SH R1 SH R2 SH R3 SH

1492-AIFM6S-31492-ACABLE_ _ _D

1746-NR4I0

R0

S0

SH

Channel 0RTD

Channel 0Sense

Channel 0Return


1746-NR4

SH


1746-NR4

SH

Leave One SensorWire Opened

1492-AIFM6S-3

Channel 0RTD

Channel 0Sense

Channel 0Return

I0

R0

S0

Channel 0RTD

Channel 0Sense

Channel 0Return

I0

R0

S0


➊

➊

➊



1756-IF6Iwith 1492-AIFM6S-3

Current Input (1492-ACABLE_ _ _X)

Current Input (1492-ACABLE_ _ _Y) ➋


➋ Important: Install “IN-V” to “IN-I” Jumper on RTB for each current input.

1 R1 2 R2 3 R3

SH SH SH SH

4 R4 5 R5

SH SH

1492-AIFM6S-3

IN-0/V

IN-0/I

RET-0

IN-2/V

IN-2/I

RET-2

Not UsedIN-4/V

IN-4/I

RET-4

1492-AIFM6S-3

1492-ACABLE_ _ _X1756-IF6I

SH

0

AnalogSource

+

–R0

IN-0/V

IN-0/I

RET-0

IN-2/V

IN-2/I

RET-2

Not UsedIN-4/V

IN-4/I

RET-4

1492-AIFM6S-3

1492-ACABLE_ _ _Y1756-IF6I

SH

AnalogSource

+

–

R00

➊

0

R0➋

➊



1756-IF6Iwith 1492-AIFM6S-3, continued

Voltage Input (1492-ACABLE_ _ _Y)

Voltage Input (1492-ACABLE_ _ _X) ➋


➋ Important: Remove “IN-V” to “IN-I” Jumper on RTB for each voltage input.

1 R1 2 R2 3 R3

SH SH SH SH

4 R4 5 R5

SH SH

1492-AIFM6S-3

IN-0/V

IN-0/I

RET-0

IN-2/V

IN-2/I

RET-2

Not UsedIN-4/V

IN-4/I

RET-4

1492-AIFM6S-3

1492-ACABLE_ _ _Y1756-IF6I

SH

0

AnalogSource

+

–R0

IN-0/V

IN-0/I

RET-0

IN-2/V

IN-2/I

RET-2

Not UsedIN-4/V

IN-4/I

RET-4

1492-AIFM6S-3

1492-ACABLE_ _ _X1756-IF6I

SH

0

AnalogSource

+

–R0

R00

➊

➋

➊



1756-IR6Iwith 1492-AIFM6S-3

3-Wire RTD

4-Wire RTD

A0

B01492-AIFM6S-3

R/C0 A1 R/C1A2 R/C2 A3 R/C3 A4 R/C4 A5 R/C5

SH B1 SH B2 SH B3 SH B4 SH B5 SH

IN-0/A

IN-0/B

RTN-0/C

IN-2/A

IN-2/B

RTN-2/C

Not usedIN-4/A

IN-4/B

RTN-4/C

1492-AIFM6S-3

1492-ACABLE_ _ _Z1756-IR6I

SH

B0

A0

R/C0

IN-0/A

IN-0/B

RTN-0/C

IN-2/A

IN-2/B

RTN-2/C

1492-AIFM6S-3

1492-ACABLE_ _ _Z1756-IR6I

SH

B0

A0

R/C0

Not usedIN-4/A

IN-4/B

RTN-4/C


➋ Important: Leave sensor wire open.

➋

➊

➊



1756-IT6Iwith 1492-AIFM6TC-3

IN-0

Not Used

RTN-0

IN-2

Not Used

RTN-2

Not UsedIN-4

Not Used

RTN-4

1492-AIFM6TC-3

1492-ACABLE_ _ _Y1756-IT6I

SH

0

+

– R0

0

1492-AIFM6TC-3

R0 1 R1 2 R2 3 R3 4 R4 5 R5

SH SH SH SH SH SH


➊



1756-OF6CI and -OF6VIwith 1492-AIFM6S-3

1756-OF6CI (0–550Ω)

1756-OF6CI (550–1000Ω) ➋

1756-OF6VI


➋ Important: Move “RTN” wire in 1492-ACABLE_ _ _Y to “ALT” terminal for each output 550–1000Ω.

OUT-0

ALT-0

RTN-0

OUT-2

ALT-2

RTN-2

Not UsedOUT-4

ALT-4

RTN-4

1492-AIFM6S-3

1492-ACABLE_ _ _Y1756-OF6CI

SH

0AnalogOutputDevice

+

–R0

0

1492-AIFM6S-3

R0 1 R1 2 R2 3 R3 4 R4 5 R5

SH SH SH SH SH SH

i 12

1920

OUT-0

ALT-0

RTN-0

OUT-2

ALT-2

RTN-2

Not UsedOUT-4

ALT-4

RTN-4

1492-AIFM6S-3

1492-ACABLE_ _ _Y1756-OF6CI ➋

SH

0

AnalogOutputDevice

+

–R0

i 12

1920

➊

OUT-0

Not Used

RTN-0

OUT-2

Not Used

RTN-2

Not UsedOUT-4

Not Used

RTN-4

1492-AIFM6S-3

1492-ACABLE_ _ _Y1756-OF6VI

SH

0

AnalogOutputDevice

+

–R0

12

1920

➋

➊

➊



1771-IFE Differentialwith 1492-AIFM8-3

2-Wire Transmitter

4-Wire Transmitter

1492-AIFM8-3

1492-ACABLE_ _ _E1771-IFE

Power Supply

Transmitter 1+

SHIELD

1–

Channel 1+

Channel 1–

1492-AIFM8-3



1+

SHIELD

1–

Channel 1+

Channel 1–

SHIELD MODULE COM

1+ 1– 2+ 2– 3+ 3– 4+ 4– 5+ 5– 6+ 6– 7+ 7– 8+ 8–1492-AIFM8-3


➊

➊



1771-IFE Differentialwith 1492-AIFM8-F-5

2-Wire Transmitter

4-Wire Transmitter

1492-AIFM8-F-5

SHIELD

VCOM+V V1 V2 V3 V4 V5 V6 V7

1+ 1– 2+ 2– 3+ 3– 4+ 4– 5+ 5– 6+ 6– 7+ 7–

+V

V1

1+

SHIELD

Power Supply

Transmitter

1492-AIFM8-F-5


Channel 1+

Channel 1–1–

VCOM

+V

V1

1+

SHIELD

Power Supply

Transmitter

1492-AIFM8-F-5


Channel 1+

Channel 1–1–

VCOM

8+ 8–

V8


➊

➊



1771-IFE Single-Endedwith 1492-AIFM8-3

2-Wire Transmitter

4-Wire Transmitter

1

SHIELD MODULE COM

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

1

SHIELDPower Supply


1492-ACABLE_ _ _F1771-IFE

Channel 1

Module ComMODULE COM

1492-AIFM8-3

1492-ACABLE_ _ _F


1

SHIELD

MODULE COM

Channel 1

Module Com

1771-IFE

1492-AIFM8-3


➊

➊



1771-IFE Single-Endedwith 1492-AIFM16-F-3

2-Wire Transmitter

1492-AIFM16-F-3

SHIELD

COM+V 1 2 3 4 5 6 7

V1 V2 V3 V4 V5 V6 V7 V8 V9 V10 V11 V12 V13 V14 V15 V16

8

+V

V1

1

SHIELD

Power Supply

Transmitter

1492-AIFM16-F-3


Channel 1

Module ComCOM

9 10 11 12 13 14 15 16


➊



1771-IFE Single-Endedwith 1492-AIFM16-F-5

2-Wire Transmitter

4-Wire Transmitter

1492-AIFM16-F-5

1

TB1 TB2

2 3 4 5 6 7 8 MODULE COM 9 10 11 12 13 14 15 16 MODULE COM

SHIELD 1J-11J-2 SHIELD

VCOM VCOM+V V1 V2 V3 V4 V5 V6 V7 V8 +V V9 V10 V11V12 V13V14 V15V16

+V

V1

1

SHIELD

Power Supply

Transmitter

1492-AIFM16-F-5


Channel 1


+V

V1

1

SHIELD

Power Supply

Transmitter

1492-AIFM16-F-5


Channel 1


VCOM


➊

➊



1771-ILwith 1492-AIFM8-3

SHIELD COM

1+ 1– 2+ 2– 3+ 3– 4+ 4– 5+ 5– 6+ 6– 7+ 7– 8+ 8–1492-AIFM8-3

1492-AIFM8-3

1492-ACABLE_ _ _H

1771-IL

SHIELD

1+

AnalogSource

+

–1– Channel 1

18

16

14

12

10

8

6

4

2


➊



1771-IRwith 1492-AIFM6S-3

1492-AIFM6S-31492-ACABLE_ _ _J

1771-IR

C1

B1Channel 1

18

16

14

12

10

8

6

4

2

1492-AIFM6S-3

A1 C1 A2 C2 A3 C3 A4 C4 A5 C5 A6 C6

SH SH SH SH SH SH

A1

SH

Channel 2

Channel 3

Channel 4

Channel 5

Channel 6

181716

151413

12

1110

9

876

5

432

1

CBA

CBA

C

BAC

BAC

B

ACB

A

B1 B2 B3 B4 B5 B6


➊



1771-OFE1, -OFE2, -OFE3with 1492-AIFM4-3

1492-AIFM4-3

3+ SH SH

SH 2+ 2– SH

3– 4+ 4–

1+ 1–

1492-AIFM4-3

1492-ACABLE_ _ _G

1771-OFE1,-OFE2, -OFE3

SH

1+

LOAD 1–Channel 1(+)

Channel 1(–)

A

0

1

2

3

4

5

6

7

B


➊


Publication 1492–2.15 September 1997 Copyright 1997 Rockwell International Corporation Printed in USA

Reference Publications1746-2.34 1746 Analog Input and Output Modules

1746-2.37 1746 RTD/Resistance Input Modules

1756-6.5.9 1756 Analog Input and Output Modules

1771-2.183 1771 Analog Input and Output Modules

Katalogy Control Tech b113 Pubs 1492215

Documents

Transcript of Katalogy Control Tech b113 Pubs 1492215