KADCAXXUSBA

USER MANUAL

USB Analogue to Digital Video Converter User Guide -

2

User’s Notice No part of this manual, including the products and software described in it, may be

reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of Kogan.

WE PROVIDE THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL KOGAN, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS), EVEN IF WE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by us; or (2) the serial number of the product is defaced or missing.

Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent infringe. Windows, MS-DOS, and DirectX are registered trademarks of Microsoft Corporation. Adobe and Acrobat are registered trademarks of Adobe Systems Incorporated. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number. Manual updates are represented by the third digit in the manual revision number.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATION USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY US. WE ASSUME NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Copyright © 2013. All Rights Reserved.

3

Contents: Chapter 1: Introduction ...................................................................................................................... 4

1.1 - Package Contents ............................................................................................................... 4

1.2 - System Requirements ........................................................................................................ 4

Chapter 2: Getting Started ................................................................................................................. 5

2.1 - Hardware Installation ........................................................................................................ 5

2.2 - Device Driver Installation ................................................................................................. 5

2.3 - Install the DirectX® ........................................................................................................ 10

2.4 - Install the Utility software. .............................................................................................. 11

Chapter 3: Launch the Program ....................................................................................................... 16

3.1 - Running the for the first time .......................................................................................... 16

3.2 - Recorder Video ................................................................................................................ 18

3.3 - Playback Video ................................................................................................................ 18

3.4 - Browse Image .................................................................................................................. 20

Chapter 4: Technical Support ........................................................................................................... 21

4

Chapter 1: Introduction

1.1 - Package Contents The following items are included in the package. CD Setup Disc (includes Software Driver and Utility Software) USB Analogue to Digital Video Converter USB Cable

1.2 - System Requirements Intel Pentium IV 2.0.GHz CPU or better processor Minimum 256 MB memory Minimum 1GB hard disk space available VGA and with DirectDraw® driver supporting 16 bit color or higher One free USB host USB 2.0 compliant interface Microsoft Windows® XP/ Windows Vista™ / Windows 7 CD-ROM drive for driver and software installation

5

Chapter 2: Getting Started 2.1 - Hardware Installation Refer to the device connection diagram below for port connections:

1. Connect the Device to PC USB Hub.

2.2 - Device Driver Installation Place the CD software that comes with the Video Converter in the CD-ROM drive. (Assuming that the. Video Converter is properly installed to the computer’s USB host), then follow the on-screen installation guide below.

Device driver installation for Windows® XP Home/Professional Edition/x64 Edition 1. When the computer is powered-on for the

very first time during the setup, amessage “Found New Hardware Wizard”dialogue box will appear on the screen.Click “Cancel” button to close “Found New Hardware Wizard” window.

6

2. Insert the Video Converter setup CD intothe CD-ROM or DVD-ROM, “Driver &Utilities” setup screen will appear. Click“Setup Driver” button.

3. Wait Installation Wizard copyingnecessary driver files onto your system.

4. Click “Finish” button

7

5. To make sure the driver is installed andstarted open the “Device Manager” Utility right after the installation. Go to “Control Panel”, double-click “System”, click on “Hardware” tab, click on “Device Manager”, double-click the “Sound, video and game controller”

8

Device driver installation for Windows Vista™ 1. When the computer is powered-on for the

very first time during the setup, amessage “Found New Hardware”dialogue box will appear on the screen.Click “Cancel” button to close “Found New Hardware” window.

2. Insert the USB TV box setup CD into theCD-ROM or DVD-ROM, “Driver & Utilities” setup screen will appear. Click “SetupDriver” button.

3. Wait Installation Wizard copyingnecessary driver files onto your system.

9

4. Click “Finish” button.

5. To make sure the driver is installed andstarted open the “Device Manager” Utilityright after the installation. Go to “ControlPanel”, double-click “System”, click on“Hardware” tab, click on “DeviceManager”, double-click the “Sound, videoand game controller”

10

2.3 - Install the DirectX® Microsoft DirectX® allows 3D hardware acceleration support in Windows® XP/64 bit and Windows Vista™ 32bit/64bit. Follow the installation steps below to install MS DirectX®.

1. Insert the installation CD into theCD-ROM drive. The setup screen willautomatically appear.

2. Click the “DirectX” button.

3. Click “Accept the agreement” radio buttonthen click “Next”

4. Click “Next” to confirm the installation ofDirectX

11

5. Click “Finish”

NOTE: The computer will automatically restart. Please close all programs if any and save files if needed before hitting the “Finish” button.

2.4 - Install the USB TV Box Utility software. 1. Install TV application on Windows XP Home/Professional Edition

1. Insert the installation CD into theCD-ROM drive. The setup screenshould automatically appear.

2. Click the “Setup Utility”

3. Please select installing language,. thenclick "Next"

12

4. Click “Next” button to start the USB TV Box Installation

5. Make sure the “Complete” button isselected then click “Next”

6. Click “Install” button to install thesoftware

13

7. Please wait a moment

6. Click “Finish” button. NOTE: We recommend restarting your computer right after the Installation Wizard.

2. Install TV application on Windows Vista 32bit

1. Click “Setup Utility”

14

2. Please select language ,then click "Next"

3. Click “Next” button to start the USB TV Box Installation

4. Make sure the “Complete” button is selected then click “Next”

15

5. Click “Install” button to install the software

6. Please wait a moment

7. Click “Finish” to restart your computer.

NOTE: We recommend restarting your computer right after the Installation Wizard.

16

Chapter 3: Launch the Video Converter Program 3.1 - Running the USB Video Converter for the first time Click “Start”, move your mouse to “Programs\USB TV Box” then click “USB TV Box”

17

This section lets you view and edit the settings for video recording. You may use both the remote control and the toolbar. Options include: 1. Double click to full screen display. 2. Browse Image 3. Snapshot still image 4. Video format select. 5. Video/Audio record 6. Movie Player 7. Source Switch: click it to select Video In or S-Video In. 8. Volume control: Adjust the Volume or mute.

8.Volume Control

7.Source Switch

6. Movie Player

5. Record

4. Video Format

3. Snapshot

2. Browse Image

1. Double click to full screen

display

18

3.2 Record Video

3.3Playback Video

Click the “Playback” button to Play the recording Video.

1.Select the “Video Source” and “Video Source Standard”. Notes: If you cannot hear any audio, please check the audio device.

2. Select the “Record Format” from drop-down list: MEPG1 MPEG2 VCD DVD HIDVD MPEG4

19

Click “Play List” button to select video file. Choose the video then click “open” button.

Exit：

To exit the video playback window, [Esc] or [ALT]+[F4] on keyboard equalized

Minimize： To minimize the video playback window, click "MoviePlayer" in desktop taskbar to restore display

Hide Control Panel： To hide video control panel, right click video window and select "Control Panel" to restore display

Setting： Click to pop-up setting dialog, you can test the video playback, detailed operation please refer to "Playback Setting" page.

Browse Image： To launch image browse window and browse the snapshot or saved image in your computer, detailed operation please refer to "Image Browse" page

Step Backward： To step backward play video

Step Forward： To step forward play video

Slow Backward： To slow backward play video

Slow Forward： To slow forward play video file

Play/Pause： Click to play the current video file, click again to pause, click once more to

20

continue play

Fast Backward：To fast backward play video file

Fast Forward： To fast forward play video file

Mute：To close sound, click again to restore.

Volume Adjust： Drag the slider to adjust volume, Left and Right arrow on keyboard equalized

Stop Play： Stop playing current video file

Snapshot： Save current video as BMP or JPG image File is default named as snapshot time and saved into C:\My Pictures folder. You also can open "Snap Setting" option in "Options" dialog, set snapshot saving directory, image format, and select rename after snapshot or not, detailed operation please refer to "Playback Setting" page

Play List：Click to pop-up sub panel below main panel, default list the record file under record directory, from which you can select the needed item to play.

3.4 Browse Image

Click the “Browse Image” to retrieve the saved pictures.

You can use the “Browse Image” software to control picture zoom in/out, or rename.

The top toolbar contains many function buttons for you to easily operate:

Refresh:：

To renew display snapshot image in current folder.

Path Panel：

Show/Hide path panel on the left of window, which is for you to easily browse and select folder.

Image Panel：

Show/Hide image panel on the left of window, through which you can easily preview snapshot image.

21

Set Wallpaper：

Set the current image as wallpaper of Windows desktop, click the right dropped arrow you can select wallpaper display mode.

Skin：

To set appearance of image browse window, you can select your favorite panel from the right dropped box.

Zoom out：

To shrink display current image

Zoom in：

To magnify current image

Match Zoom：

You can select the matched display mode in the right dropped box. Full Size: Shows image at 100% magnification; Fit Image: Magnifies image to fit screen or window; Fit Width: Magnifies image to fit width of screen or window; Fit Height: Magnifies image to fit height of screen or window; Lock: Locks the viewer at the current magnificent level.

Chapter 4: Technical Support For Technical Support or Installation Hotline contacts please visit kogan.com.au.