JVC-GRD250 Camcorder Manual

8/8/2019 JVC-GRD250 Camcorder Manual

1/48

ENGLISH

GR-D250

LYT1353-001A EN

Dear Customer,Thank you for purchasing this digitalvideo camera. Before use, pleaseread the safety information andprecautions contained in the pages3 4 and 9 to ensure safe use of thisproduct.

Please visit our Homepage on the World Wide Web forDigital Video Camera:

For Accessories:

http://www.jvc.co.jp/english/cyber/

http://www.jvc.co.jp/english/accessory/

INSTRUCTIONS

DIGITAL VIDEO CAMERAGETTING STARTED 6

VIDEO RECORDING &

PLAYBACK 17

ADVANCED FEATURES 22

REFERENCES 38

TERMS

For Customer Use:Enter below the Model No. andSerial No. which is located on thebottom of the camcorder. Retain thisinformation for future reference.Model No.

Serial No.

To deactivate the demonstration,set DEMO MODE to OFF.( pg. 22, 25)

47


2/48

2 EN

Wipe/Fader EffectsYou can use the Wipe/Fader Effects to make

pro-style scene transitions. ( pg. 33)

Program AE with Special EffectsFor example, SPORTS mode allows fast-

moving images to be captured one frame at a

time, for vivid, stable slow-motion. ( pg. 34)

Backlight CompensationSimply pressing the BACK LIGHT buttonbrightens the image darkened by backlight.( pg. 31)

You can also select a spot metering area so

that more precise exposure compensation

is available. ( pg. 31, Spot Exposure

Control)

Data BatteryYou can check the battery status by simply

pressing the DATA button. ( pg. 12)

Major Features of this Camcorder

Fade in

Fade out

MAX TIMELEVEL

LCD

60min

FINDER

80min

100%

50

0

BATTERY CONDITION


3/48

EN 3SAFETY PRECAUTIONS

WARNING: TO PREVENT FIRE OR SHOCKHAZARD, DO NOT EXPOSE THIS UNIT TORAIN OR MOISTURE.

CAUTIONS:

This camcorder is designed to be used withNTSC-type color television signals. It cannot beused for playback with a television of a differentstandard. However, live recording and LCD

monitor/viewfinder playback are possibleanywhere.

This product includes patented and otherproprietary technology and will operate onlywith JVC Data Battery. Use the JVCBN-VF707U/VF714U/VF733U battery packsand, to recharge them or to supply power to thecamcorder from an AC outlet, use the providedmulti-voltage AC Adapter. (An appropriateconversion adapter may be necessary toaccommodate different designs of AC outlets in

different countries.)

Caution on Replaceable lithium batteryThe battery used in this device may present a fireor chemical burn hazard if mistreated.

Do not recharge, disassemble, heat above 100C(212F) or incinerate.

Replace battery with Panasonic (MatsushitaElectric), Sanyo, Sony or Maxell CR2025.

Danger of explosion or Risk of fire if the battery isincorrectly replaced.

Dispose of used battery promptly. Keep away from children. Do not disassemble and do not dispose of in

fire.

CAUTIONRISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within anequilateral triangle, is intended to alert the user to thepresence of uninsulated "dangerous voltage" within theproduct's enclosure that may be of sufficient magnitudeto constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle isintended to alert the user to the presence of importantoperating and maintenance (servicing) instructions inthe literature accompanying the appliance.

NOTES:

The rating plate (serial number plate) andsafety caution are on the bottom and/or theback of the main unit.

The rating information and safety caution of theAC Adapter are on its upper and lower sides.

This product has a fluorescent lamp that containsa small amount of mercury. Disposal of thesematerials may be regulated in your communitydue to environmental considerations.For disposal or recycling information pleasecontact your local authorities, or the ElectronicsIndustries Alliance:


4/48

4 ENIMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install inaccordance with the manufacturers instructions.

8. Do not install near any heat sources such asradiators, heat registers, stoves, or otherapparatus (including amplifiers) that produceheat.

9. Only use attachments/accessories specified bythe manufacturer.

10. Use only with thecart, stand, tripod,bracket, or table

specified by themanufacturer, orsold with theapparatus. When acart is used, usecaution whenmoving the cart/apparatus combination to avoid injury from tip-over.

11. Unplug this apparatus during lightning storms or

when unused for long periods of time.12. Refer all servicing to qualified servicepersonnel. Servicing is required when theapparatus has been damaged in any way, suchas power-supply cord or plug is damaged, liquidhas been spilled or objects have fallen into theapparatus, the apparatus has been exposed torain or moisture, does not operate normally, orhas been dropped.

When the equipment is installed in a cabinet or ona shelf, make sure that it has sufficient space onall sides to allow for ventilation (10 cm (315/16")or more on both sides, on top and at the rear).

Do not block the ventilation holes.(If the ventilation holes are blocked by anewspaper, or cloth etc. the heat may not be ableto get out.)

No naked flame sources, such as lighted candles,should be placed on the apparatus.

When discarding batteries, environmentalproblems must be considered and the local rulesor laws governing the disposal of these batteriesmust be followed strictly.

The apparatus shall not be exposed to dripping orsplashing.

Do not use this equipment in a bathroom orplaces with water.Also do not place any containers filled with wateror liquids (such as cosmetics or medicines, flowervases, potted plants, cups etc.) on top of this unit.(If water or liquid is allowed to enter thisequipment, fire or electric shock may be caused.)

Do not point the lens or the viewfinder directly intothe sun. This can cause eye injuries, as well aslead to the malfunctioning of internal circuitry.There is also a risk of fire or electric shock.

CAUTION!

The following notes concern possible physicaldamage to the camcorder and to the user.

When carrying, be sure to always securely attachand use the provided strap. Carrying or holdingthe camcorder by the viewfinder and/or the LCDmonitor can result in dropping the unit, or in amalfunction.

Take care not to get your finger caught in thecassette holder cover. Do not let children operatethe camcorder, as they are particularlysusceptible to this type of injury.

Do not use a tripod on unsteady or unlevelsurfaces. It could tip over, causing seriousdamage to the camcorder.

CAUTION!

Connecting cables (Audio/Video, S-Video, etc.) tothe camcorder and leaving it on top of the TV isnot recommended, as tripping on the cables willcause the camcorder to fall, resulting in damage.


5/48

EN 5CONTENTS

GETTING STARTED 6

ndex................................................................. 6Provided Accessories .....................................10Power.............................................................. 11Operation Mode.............................................. 13Language Settings..........................................14Date/Time Settings .........................................14Grip Adjustment .............................................. 14Viewfinder Adjustment ....................................15Brightness Adjustment Of The Display ........... 15Tripod Mounting.............................................. 15Loading/Unloading A Cassette .......................16

VIDEO RECORDING & PLAYBACK 17

VIDEO RECORDING ........................................... 17Basic Recording.............................................. 17

Tape Remaining Time ................................17LCD Monitor And Viewfinder ......................18Zooming...................................................... 18Journalistic Shooting ..................................19Time Code .................................................. 19Quick Review.............................................. 19Recording From The Middle Of A Tape...... 19

VIDEO PLAYBACK ............................................. 20Normal Playback............................................. 20

Still Playback .............................................. 20

Shuttle Search ............................................ 20Blank Search .............................................. 20

Connections To A TV Or VCR ........................21

ADVANCED FEATURES 22

MENUS FOR DETAILED ADJUSTMENT.................. 22Changing The Menu Settings .........................22Recording Menus............................................ 23Playback Menus ............................................. 26

FEATURES FOR RECORDING...............................28

5-Second Recording.......................................28Night-Alive ...................................................... 28Snapshot (For Video Recording) ....................29Manual Focus ................................................. 29Exposure Control ............................................ 30Iris Lock .......................................................... 30Backlight Compensation .................................31Spot Exposure Control....................................31White Balance Adjustment..............................32Manual White Balance Adjustment................. 32

Wipe Or Fader Effects ....................................33Program AE With Special Effects ...................34

EDITING............................................................ 35Dubbing To A VCR .........................................35Dubbing To Or From A Video Unit Equipped With

A DV Connector (Digital Dubbing).............. 36Connection To A Personal Computer ............. 37

REFERENCES 38

TROUBLESHOOTING .......................................... 38USER MAINTENANCE.........................................42CAUTIONS ........................................................ 43SPECIFICATIONS................................................ 46

TERMS 47


6/48

6 EN GETTING STARTED

Index

1

R S

B C D E

78

JI K LQ

T

6

N

O

P

VU W X

Y

a

Z

b c M

d


7/48

EN 7GETTING STARTED

ControlsA Stop Button [8] ( pg. 20)

Backlight Compensation Button [BACKLIGHT] ( pg. 31)

B Play/Pause Button [4/9] ( pg. 20)Manual Focus Button [FOCUS] ( pg. 29)

C Rewind Button [3] ( pg. 20)

Menu select Button [] ( pg. 14)Quick Review Button [ ] ( pg. 19)

D Fast-Forward Button [5] ( pg. 20)Menu select Button [+] ( pg. 14)Night Button [NIGHT] ( pg. 28)

E Menu Button [MENU] ( pg. 22)Data Battery Button [DATA] ( pg. 12)

F Dioptre Adjustment Control ( pg. 15)G Snapshot Button [SNAPSHOT] ( pg. 29)H Power Zoom Lever [T/W] ( pg. 18)

Speaker Volume Control [VOL. +, ]( pg. 20)

I Battery Release Button [PUSH BATT.]( pg. 11)

J Recording Start/Stop Button ( pg. 17)K Power Switch [A, M, PLAY, OFF] ( pg. 13)L Lock Button ( pg. 13)M Cassette Open/Eject Switch [OPEN/EJECT]

( pg. 16)

ConnectorsThe connectors are located beneath the covers.N Audio/Video Output Connector [AV]

( pg. 21, 35)O DC Input Connector [DC] ( pg. 11)P Digital Video Connector [DV IN/OUT] (i.Link*)

( pg. 36, 37)i.Link refers to the IEEE1394-1995 industryspecification and extensions thereof. The logois used for products compliant with the i.Link

standard.

ndicatorsQ POWER/CHARGE Lamp ( pg. 11, 17)

Other PartsR Monitor Latch ( pg. 18)S LCD Monitor ( pg. 18, 19)T Viewfinder ( pg. 15)U Battery Pack Mount ( pg. 12)V Shoulder Strap Eyelet ( pg. 11)W Speaker ( pg. 20)

X Grip Strap ( pg. 14)Y LensZ Camera Sensor

(Be careful not to cover this area, a sensornecessary for shooting is built-in here.)

a Stereo Microphoneb Stud Hole ( pg. 15)c Tripod Mounting Socket ( pg. 15)d Cassette Holder Cover ( pg. 16)


8/48

GETTING STARTED8 ENLCD Monitor/Viewfinder IndicationsDuring Video Recording

a Operation Mode ( pg. 13)B : Night-Alive Indicator ( pg. 28): Gain Up Mode ( pg. 23)

C White Balance Indicator ( pg. 32)D : Spot Exposure Control Indicator

( pg. 31): Backlight Compensation Indicator

( pg. 31): Exposure Adjustment Indicator ( pg. 30)

E Selected Program AE With Special Effects

Indicator ( pg. 34)F Iris Lock Indicator ( pg. 30)G SOUND 12BIT/16BIT: Sound Mode Indicator

( pg. 23) (Appears for approx. 5 secondsafter turning on the camcorder.)

H Digital Image Stabilizer (DIS) ( pg. 24)I Approximate Zoom Ratio ( pg. 18)J Zoom Indicator ( pg. 18)K Selected Wipe/Fader Effect Indicator

( pg. 33)

L Tape Running Indicator ( pg. 17)(Rotates while tape is running.)

M Selected Wide Mode Indicator ( pg. 24)N Recording Speed Mode (SP/LP) ( pg. 23)O Tape Remaining Time ( pg. 17)P REC: (Appears during recording.) ( pg. 17)

PAUSE: (Appears during Record-Standbymode.) ( pg. 17)O: (Appears when taking Snapshot.)( pg. 29)

Q 5S/Anim.: Displays the 5-Second Recordingmode or Animation recording mode.( pg. 24)

R Wind Cut Indicator ( pg. 24)S Battery Remaining Power Indicator

( pg. 40)T Date/Time ( pg. 14)

U Brightness Control Indicator (LCD monitor/Viewfinder) ( pg. 15)

V Manual Focus Adjustment Indicator( pg. 29)

W Time Code ( pg. 26, 27)

50m

O

V

0

1

0

0

0

'0

A

5

M:

25

x

W

T

BRIGHT

1

SOUND 12BI T

1h40m

N15:55

REC

456

12

3

9 0

pas

8

q we t

y

u

i

o

r

7

d


9/48

EN 9GETTING STARTED

During Video Playback

a Sound Mode Indicator ( pg. 26)B Blank Search Indicator ( pg. 20)

C Tape Speed ( pg. 23)D4: Playback5: Fast-Forward/Shuttle Search3: Rewind/Shuttle Search9: Pause9U: Forward Frame-By-Frame Playback/Slow-MotionY9: Reverse Frame-By-Frame Playback/Slow-Motion

E Battery Remaining Power Indicator

( pg. 40)F Date/Time ( pg. 26, 27)G VOLUME: Volume Level Indicator ( pg. 20)

BRIGHT: Brightness Control Indicator (LCDmonitor/Viewfinder) ( pg. 15)

H Time Code ( pg. 26, 27)

Before Using This Camcorder

Make sure you only use cassettes with the MiniDV mark .This camcorder is designed exclusively for thedigital video cassette. Only cassettes marked can be used with this unit.

Remember that this camcorder is notcompatible with other digital video formats.Remember that this camcorder is intended forprivate consumer use only.Any commercial use without proper permission isprohibited. (Even if you record an event such as ashow, performance or exhibition for personalenjoyment, it is strongly recommended that youobtain permission beforehand.)

Before recording important video, be sure tomake a trial recording.

Play back your trial recording to make sure thevideo and audio have been recorded properly.

We recommend cleaning your video headsbefore use.If you havent used your camcorder for a while, theheads may be dirty. We recommend periodicallycleaning the video heads with a cleaning cassette(optional).

Be sure to store your cassette tapes andcamcorder in the proper environment.Video heads can become dirty more easily if your

cassette tapes and camcorder are stored in a dustyarea. Cassette tapes should be removed from thecamcorder and stored in cassette cases. Store thecamcorder in a bag or other container.

Use SP (Standard) mode for important videorecordings.LP (Long Play) mode lets you record 50% morevideo than SP (Standard) mode, but you mayexperience mosaic-like noise during playbackdepending on the tape characteristics and theusage environment.

So, for important recordings, we recommend usingSP mode.

It is recommended that you use JVC brandcassette tapes.Your camcorder is compatible with all brands ofcommercially available cassette tapes complyingwith the MiniDV standard, but JVC brand cassettetapes are designed and optimized to maximize theperformance of your camcorder.

Also read CAUTIONS on pages 43 45.

1

L2

2

0

:

/

2

M

V

1

I

O

:

X

L

2

B I T

U

5

M

E

N

O

1

V

0

1

00

0 ' 0

A

5

M:

1 2 43

5

78 6

BLANK SEARCH

PUSH "STOP" BUTTONTO CANCEL

50m


10/48

GETTING STARTED10 EN

a AC Adapter AP-V16U or AP-V14Ub Battery Pack BN-VF707Uc Audio/Video Cable (3.5 mini-plug to RCA

plug)d Shoulder Strap ( pg. 11 for attachment)e Lens Cap (see the right column for

attachment)

NOTES: In order to maintain optimum performance of the

camcorder, provided cables may be equipped withone or more core filter. If a cable has only one corefilter, the end that is closest to the filter should beconnected to the camcorder.

Make sure to use the provided cables forconnections. Do not use any other cables.

How To Attach The Lens CapTo protect the lens, attachthe provided lens cap to thecamcorder as shown in theillustration.

NOTE:

To confirm the lens cap is oncorrectly make sure the cap isflush to the camcorder.

Provided Accessories

OR

Place here duringshooting.


11/48

EN 11GETTING STARTED

How To Attach The Shoulder StrapFollow the illustration.

1 Thread the strap through the eyelet.

2 Fold it back and thread it through the strapguide and the buckle.

To adjust the length of the strap, loosen and then

tighten the strap in the buckle.3 Slide the strap guide fully towards the eyelet.

This camcorders 2-way power supply systemlets you choose the most appropriate source ofpower. Do not use provided power supply unitswith other equipment.

Charging The Battery Pack

1 Set the Power Switch to OFF.

2 With the arrow on the battery pack pointingdownward, push the battery pack slightly againstthe battery pack mount a.

3 Slide down the battery pack until it locks inplace b.

4 Connect the AC Adapter to the camcorder.5 Plug the AC Adapter into an AC outlet. ThePOWER/CHARGE lamp on the camcorderblinks to indicate charging has started.

6 When the POWER/CHARGE lamp goes out,charging is finished. Unplug the AC Adapterfrom the AC outlet. Disconnect the AC Adapter

from the camcorder.

1

2

2

3

Strap guide

Buckle

Eyelet

Power

POWER/CHARGE

PLAYOFFM A POWER/CHARGE lamp

Battery pack

PUSH BATT.

Open the cover.

Power switch

mark

Arrow

Battery pack mount

To DC connector

To AC outletAC Adapter


12/48

GETTING STARTED12 ENTo detach the battery packSlide the battery pack upward while pressingPUSH BATT. to detach it.

* Provided

NOTES: It is recommended that only genuine JVC

batteries are used in this camcorder. Usinggeneric non-JVC batteries can cause damage tothe internal charging circuitry.

If the protective cap is attached to the batterypack, remove it first.

During charging, the camcorder cannot beoperated. Charging is not possible if the wrong type of

battery is used. When charging the battery pack for the first time

or after a long storage period, the POWER/CHARGE lamp may not light. In this case, removethe battery pack from the camcorder, then trycharging again.

If the battery operation time remains extremelyshort even after having been fully charged, the

battery is worn out and needs to be replaced.Please purchase a new one.

Since the AC Adapter processes electricityinternally, it becomes warm during use. Be sure touse it only in well-ventilated areas.

Using the optional AA-VF7 Battery Charger, youcan charge the BN-VF707U/VF714U/VF733Ubattery pack without the camcorder.

After 5 minutes has elapsed in Record-Standbymode with the cassette inserted, the camcorderwill automatically turn off its power supplied fromthe AC adapter. In this case, the battery chargestarts if the battery is attached to the camcorder.

Using The Battery Pack

Perform steps 2 3in Charging The BatteryPack.

Maximum continuous recording time

* Provided

NOTES: Recording time is reduced significantly under the

following conditions: Zoom or Record-Standby mode is engaged

repeatedly. The LCD monitor is used repeatedly. The playback mode is engaged repeatedly.

Before extended use, it is recommended that youprepare enough battery packs to cover 3 times theplanned shooting time.

ATTENTION:Before detaching the power source, make sure thatthe camcorders power is turned off. Failure to do socan result in a camcorder malfunction.

Data Battery SystemYou can check the remaining battery power andthe recordable time.1) Make sure the battery is attached and thePower Switch is set to OFF.2) Open the LCD monitor fully.3) Press DATA, and the battery status screenappears. It can be displayed on the viewfinder when the

LCD monitor is closed. It is displayed for approx. 5 seconds if the

button is pressed and released quickly, and forapprox. 15 seconds if the button is pressedand hold for several seconds.

If COMMUNICATION ERROR appearsinstead of the battery status even though youtried to press DATA several times, there maybe a problem with your battery. In such a case,consult your nearest JVC dealer.

Battery pack Charging time

BN-VF707U* Approx. 1 hr. 30 min.

BN-VF714U Approx. 2 hr. 40 min.

BN-VF733U Approx. 5 hr. 40 min.

Battery packLCD monitor

onViewfinder on

BN-VF707U* 1 hr. 5 min. 1 hr. 25 min.

BN-VF714U 2 hr. 20 min. 3 hr.

BN-VF733U 5 hr. 25 min. 7 hr. 5 min.


13/48


Using AC PowerPerform step 4in Charging The Battery Pack.

NOTE:The provided AC Adapter features automaticoltage selection in the AC range from 110 V to40 V.

About BatteriesDANGER! Do not attempt to take the batteriesapart, or expose them to flame or excessiveheat, as it may cause a fire or explosion.WARNING! Do not allow the battery or itserminals to come in contact with metals, as thisan result in a short circuit and possibly start are.

To resume the original function of the

accurate battery power indicationf the battery power indication differs from theactual operating time, fully charge the battery,and then run it down. However this function maynot turn back if the battery was used for a longperiod of time under extremely high/lowemperature condition or charged too manymes.

To turn on the camcorder, set the Power Switchto any operation mode except OFF whilepressing down the Lock Button located on theswitch.

Choose the appropriate operation modeaccording to your preference using the PowerSwitch.

Operation Mode

Power Switch Position

A (Full Auto Recording):Allows you to record using NO special effectsor manual adjustments. Suitable for standardrecording.

The A indicator appears on the display.M (Manual Recording):Allows you to set various recording functionsusing the Menus. ( pg. 22)If you want more creative capabilities than FullAuto Recording, try this mode.

OFF:Allows you to switch off the camcorder.

PLAY:

Allows you to play back a recording on thetape.Allows you to set various playback functions

using the Menus. ( pg. 22)

POWER/CHARGE

M A

POWER/CHARGE lamp

Power Switch

Lock Button

MENU/DATA


14/48

GETTING STARTED14 ENPower-Linked OperationWhen the Power Switch is set to A or M, youcan also turn on/off the camcorder by opening/closing the LCD monitor or pulling out/pushing inthe viewfinder.

INFORMATION:

The following explanations in this manualsupposes the use of LCD monitor in youroperation. If you want to use the viewfinder,close the LCD monitor and pull out theviewfinder fully.

The language on the display can be changed.( pg. 22, 26, 27)

1 Set the Power Switch to M while pressingdown the Lock Button located on the switch.

2 Open the LCD monitor fully. ( pg. 18)

3 Press MENU. The Menu Screen appears.4 Press + or to selectn, and press MENU.The CAMERA DISPLAYMenu appears.

5 Press + or to selectLANGUAGE, and pressMENU.

6 Press + or to selectthe desired language, andpress MENU.

7 Press + or to selectBRETURN, and pressMENU twice. The Menu

Screen closes.

The date/time is recorded onto the tape at alltimes, but its display can be turned on or offduring playback. ( pg. 22, 27)

1 Perform steps 1 4 in Language Settings

on the left column.2 Press + or to select CLOCK ADJ., andpress MENU. The parameter for Month ishighlighted.

3 Press + or to inputthe month, and pressMENU. Repeat to inputthe day, year, hour andminute.

4Press + or to selectBRETURN, and press

MENU twice. The Menu Screen closes.

1 Adjust the velcro strip.

2 Pass your right handthrough the loop and graspthe grip.

3 Adjust your thumb andfingers through the grip toeasily operate theRecording Start/StopButton, Power Switch andPower Zoom Lever. Besure to fasten the velcro strip to your preference.

Language Settings

NRETUR

LADA SERAC M I YPBRIGHT

LC T/DAUMET / T IDA E OTOFDEM COT I E F

V

O KCL CJAD .

NCREON S E

LANGUAGE ENGLISHDEC 02

: 0 0 5' 0 5PM

LADA SERAC M I YP

ENGLISHESPAOL

LANGUAGE

Date/Time Settings

Grip Adjustment

LADA SERAC M I YP

O KCL CJAD .

DEC 02: 0 0 5

' 0 5PM


15/48


1 Set the Power Switch to A or M whilepressing down the Lock Button located on thewitch.

2 Make sure the LCD monitor is closed andocked. Pull out the viewfinder fully and adjust itmanually for best viewability.

3 Turn the Dioptre Adjustment Control until thendications in the viewfinder are clearly focused.

CAUTION:When retracting the viewfinder, take care not to

inch your fingers.

1 Set the Power Switchto M or PLAY whilepressing down the Lock

Button located on theswitch.

2 Open the LCD monitorfully. ( pg. 18) To adjust the brightness of

the viewfinder, pull out theviewfinder fully and setPRIORITY to FINDER( pg. 22, 25).

3 Press MENU. TheMenu Screen appears.4 Press + or to select n, and press MENU.The CAMERA DISPLAY Menu appears.

5 Press + or to select BRIGHT, and pressMENU. The Menu Screen closes and thebrightness control indicator appears.

6 Press + or until the appropriate brightnessis reached.

7 Press MENU to clear the brightness controlindicator from the display.

To attach the camcorderto a tripod, align thedirection stud and screwto the mounting socketand stud hole on the

camcorder. Then tightenthe screw clockwise.Some tripods are not

equipped with studs.

Viewfinder Adjustment

PAUSE

Dioptre Adjustment Control

Example:

Brightness Adjustment Of TheDisplay

Tripod Mounting

BRIGHT

MENU

+


16/48

GETTING STARTED16 EN

The camcorder needs to be powered up to loador eject a cassette.

1 Slide and hold OPEN/EJECT in the directionof the arrow, then pull the cassette holder coveropen until it locks. The cassette holder opensautomatically. Do not touch internal components.

2 Insert or remove a tape and press PUSHHERE to close the cassette holder. Be sure to press only the section labelled PUSH

HERE to close the cassette holder; touchingother parts may cause your finger to get caught inthe cassette holder, resulting in injury or productdamage.

Once the cassette holder is closed, it recedesautomatically. Wait until it recedes completelybefore closing the cassette holder cover.

When the battery packs charge is low, you maynot be able to close the cassette holder cover. Do

not apply force. Replace the battery pack with afully charged one or use AC power beforecontinuing.

3 Close the cassette holder cover firmly until itlocks into place.

To protect valuable recordingsSlide the erase protection tab on the back of thetape in the direction of SAVE. This prevents thetape from being recorded over. To record on thistape, slide the tab back to REC before loadingit.

NOTES: If you wait a few seconds and the cassette holder

does not open, close the cassette holder coverand try again. If the cassette holder still does notopen, turn the camcorder off then on again.

If the tape does not load properly, open thecassette holder cover fully and remove thecassette. A few minutes later, insert it again.

When the camcorder is suddenly moved from acold place to a warm environment, wait a shorttime before opening the cassette holder cover.

Loading/Unloading A Cassette

Make sure the window sideis facing out.

Cassette holdercover

Cassette holder

PUSH HERE

OPEN/EJECTEraseprotection tab


17/48

EN 17VIDEO RECORDING

NOTE:Before continuing, perform the procedures listedelow:Power ( pg. 11)Loading A Cassette ( pg. 16)

1 Remove the lens cap. ( pg. 10)

2 Open the LCD monitor fully.3 Set the Power Switch to A or M whilepressing down the Lock Button located on thewitch.The POWER/CHARGE lamp lights and thecamcorder enters the Record-Standby mode.PAUSE is displayed.

To record in LP (Long Play) mode,

pg. 23.4 To start recording, press the Recording Start/Stop Button. T REC appears on the displaywhile recording is in progress.

5 To stop recording, press the Recording Start/Stop Button again. The camcorder re-enters theRecord-Standby mode.

Approximate recording time

NOTES:If the Record-Standby mode continues for5 minutes, the camcorders power shuts offautomatically. To turn the camcorder on again,

push back and pull out the viewfinder again orclose and re-open the LCD monitor.When a blank portion is left between recordedscenes on the tape, the time code is interruptedand errors may occur when editing the tape. Toavoid this, refer to Recording From The Middle OfA Tape ( pg. 19).To turn the beep sounds off, pg. 22, 25.

Tape Remaining TimeApproximate tape remainingtime appears on the display. h m means thecamcorder is calculating theremaining time. When theremaining time reaches 2 minutes, the indication

starts blinking. The time required to calculate and display the

remaining tape length, and the accuracy of thecalculation, may vary according to the type of tapeused.

Basic Recording

Tape

Recording mode

SP LP

30 min. 30 min. 45 min.

60 min. 60 min. 90 min.

80 min. 80 min. 120 min.

POWER/CHARGE Lamp

Recording Start/Stop Button

Power Switch

Lock Button

Power Zoom Lever


18/48

VIDEO RECORDING18 ENLCD Monitor And ViewfinderWhile using the LCD monitor:Make sure the viewfinder is pushed back in. Pullon the end of the LCD monitor and open theLCD monitor fully. It can rotate 270 (90downward, 180 upward).

While using the viewfinder:Make sure the LCD monitor is closed andlocked. Pull out the viewfinder fully.

NOTES: The image will not appear simultaneously on the

LCD monitor and the viewfinder. When theviewfinder is pulled out while the LCD monitor isopened, you can select which one to use. SetPRIORITY to the desired mode in SYSTEMMenu. ( pg. 22, 25)

Colored bright spots may appear all over the LCDmonitor or the viewfinder. However, this is not a

malfunction. ( pg. 39)

ZoomingProduces the zoom in/out effect, or aninstantaneous change in image magnification.

Zoom InSlide the Power Zoom Lever towards T.

Zoom OutSlide the Power Zoom Lever towards W. The further you slide the Power Zoom Lever, the

quicker the zoom action.

NOTES: Focusing may become unstable during Zooming.

In this case, set the zoom while in Record-Standby, lock the focus by using the manual focus( pg. 29), then zoom in or out in Record mode.

Zooming is possible to a maximum of 800X, or itcan be switched to 25X magnification using theoptical zoom. ( pg. 23)

Zoom magnification of over 25X is done throughDigital image processing, and is therefore calledDigital Zoom.

During Digital zoom, the quality of image maysuffer.

Macro shooting (as close as approx. 5 cm (2") tothe subject) is possible when the Power ZoomLever is set all the way to W. Also see TELEMACRO in MANUAL Menu on page 24.

When shooting a subject close to the lens, zoomout first. If zoomed-in in the auto focus mode, thecamcorder may automatically zoom outdepending on the distance between the

camcorder and the subject. This will not occurwhen TELE MACRO is set to ON. ( pg. 24)

180

90

10 x W T

1xW T

10 xW T

20xW T40xW T

Digital zoom zone

Zoom in (T: Telephoto)

Zoom out (W: Wide angle)

25X (optical) zoom zone

Approximate zoom ratio


19/48

EN 19VIDEO RECORDING

ournalistic Shootingn some situations,different shootingangles may providemore dramatic results.Hold the camcorder inhe desired position

and tilt the LCDmonitor in the mostonvenient direction. Itan rotate 270 (90

downward, 180pward).

Time CodeDuring recording, a time code is recorded on the

ape. This code is to confirm the location of theecorded scene on the tape during playback.

Frames are not displayed during recording.f recording starts from a blank portion, the timeode begins counting from 00:00:00minute:second:frame). If recording starts fromhe end of a previously recorded scene, the timeode continues from the last time code number.f during recording a blank portion is left partwayhrough the tape, the time code is interrupted.

When recording is resumed, the time code startsounting up again from 00:00:00. This means

he camcorder may record the same time codesas those existing in a previously recorded scene.To prevent this, perform Recording From TheMiddle Of A Tape ( pg. 19) in the followingases;When shooting again after playing back arecorded tape.When power shuts off during shooting.When a tape is removed and re-inserted duringshooting.

When shooting using a partially recorded tape.When shooting on a blank portion located partwaythrough the tape.When shooting again after shooting a scene thenopening/closing the cassette holder cover.

NOTES: The time code cannot be reset. During fast-forwarding and rewinding, the time

code indication does not move smoothly. The time code is displayed only when TIME

CODE is set to ON. ( pg. 26)

Quick ReviewEnables to check the end of the last recording.1) Press during the Recording-Standbymode.2) Tape is rewound for about several secondsand played back automatically, then pauses inthe Recording-Standby mode for the next shot. Distortion may occur at start of playback. This is

normal.

Recording From The Middle Of A Tape1) Play back a tape or use Blank Search( pg. 20) to find the spot at which you want tostart recording, then engage the Still Playbackmode. ( pg. 20)2) Set the Power Switch to A or M whilepressing down the Lock Button located on theswitch, then start recording.

12 : 34 : 24

Minutes

Seconds

Frames*(30 frames = 1 second)

Display


20/48

20 EN VIDEO PLAYBACK

1 Load a cassette. ( pg. 16)

2 Set the Power Switch to PLAY whilepressing down the Lock Button located on the

switch.3 To start playback, press4/9.

4 To stop playback, press 8. During Stop mode, press3 to rewind, or5

to fast-forward the tape.

To control the speaker volumeSlide the Power Zoom Lever (VOL. +/) towards+ to turn up the volume, or towards to turndown the volume.

NOTES: The playback picture can be viewed in the LCD

monitor, viewfinder or on a connected TV.( pg. 21)

If Stop mode continues for 5 minutes when poweris supplied from a battery, the camcorder shuts offautomatically. To turn on again, set the PowerSwitch to OFF, then to PLAY.

When a cable is connected to the AV connector,the sound is not heard from the speaker.

Still PlaybackPauses during video playback.1) Press4/9 during playback.2) To resume normal playback, press4/9again. If still playback continues for more than about

3 minutes, the camcorders Stop mode isautomatically engaged.

Shuttle SearchAllows high-speed search in either directionduring video playback.1) During playback, press5 for forwardsearch, or3 for reverse search.2) To resume normal playback, press4/9.

During playback, press and hold5 or3. Thesearch continues as long as you hold the button.Once you release the button, normal playbackresumes.

A slight mosaic effect appears on the displayduring Shuttle Search. This is not a malfunction.

ATTENTION:

During Shuttle Search, partsof the picture may not beclearly visible, particularly onthe left side of the screen.

Blank Search

Helps you find where you should start recordingin the middle of a tape to avoid time codeinterruption. ( pg. 19)

1 Load a cassette. ( pg. 16)

2 Set the Power Switch to PLAY whilepressing down the Lock Button located on theswitch.

3 Press MENU. The Menu Screen appears.

4 Press MENU to select t. The VIDEOMenu appears.

5 Press + or to select BLANK SRCH, andpress MENU. The Sub Menu appears.

6 Press + or to select EXECUTE, and pressMENU. The BLANK SEARCH indication appears and

the camcorder automatically starts reverse orforward search, then stops at the spot which isabout 3 seconds of tape before the beginning ofthe detected blank portion.

To cancel Blank Search, press8

.NOTES: Before starting Blank Search, if the current

position is at a blank portion, the camcordersearches in the reverse direction. If the currentposition is at a recorded portion, the camcordersearches in the forward direction.

If the beginning or end of the tape is reachedduring Blank Search, the camcorder stopsautomatically.

A blank portion which is shorter than 5 seconds oftape may not be detected. The detected blank portion may be located

between recorded scenes. Before you startrecording, make sure there is no recorded sceneafter the blank portion.

Normal Playback

M ASpeaker

4/9Lock Button

3

PowerSwitch

8

MENU

5 VOL. +/


21/48

EN 21VIDEO PLAYBACK

A Yellow to VIDEO IN (Connect when your TV/VCR has only A/V input connectors.)

B Red to AUDIO R IN*C White to AUDIO L IN*

Not required for watching still images only.

1 Make sure all units are turned off.

2 Connect the camcorder to a TV or VCR asshown in the illustration.

If using a VCR, go to step 3.If not, go to step 4.

3 Connect the VCR output to the TV input,referring to your VCRs instruction manual.

4 Turn on the camcorder, the VCR and the TV.

5 Set the VCR to its AUX input mode, and setthe TV to its VIDEO mode.

6 Start playback on the camcorder. ( pg. 20)

To choose whether or not the followingdisplays appear on the connected TV Date/Time

Set DATE/TIME to AUTO, ON or OFF.

( pg. 22, 27) Time Code

Set TIME CODE to ON or OFF.( pg. 22, 27)

Indications other than date/time and time codeSet ON SCREEN to OFF, LCD or LCD/TV.( pg. 22, 27)

NOTES: It is recommended to use the AC Adapter as

the power supply instead of the battery pack.

( pg. 13) To monitor the picture and sound from the

camcorder without inserting a tape, set thecamcorders Power Switch to A or M, then setyour TV to the appropriate input mode.

Make sure you adjust the TV sound volume to itsminimum level to avoid a sudden burst of soundwhen the camcorder is turned on.

Connections To A TV Or VCR

21 3

TV

VCR

Open the cover.

To AVconnector

Audio/Videocable

(provided)


22/48

22 EN MENUS FOR DETAILED ADJUSTMENT

This camcorder is equipped with an easy-to-use,on-screen menu system that simplifies many ofthe more detailed camcorder settings.( pg. 23 27)

1 For Video Recording Menus:Set the Power Switch to M while pressingdown the Lock Button located on the switch.

For Video Playback Menus:Set the Power Switch to PLAY while pressingdown the Lock Button located on the switch.

2 Open the LCD monitor fully. ( pg. 18)

3 Press MENU. The Menu Screen appears.4 Press + or to select the desired function,and press MENU. The selected function menuappears.

5 Setting procedure hereafter depends on theselected function.

Menus without Sub MenusvWIPE/FADER( pg. 33)r PROGRAM AE( pg. 34)p EXPOSURE( pg. 30)uW. BALANCE( pg. 32)

1) Press + or to selectthe desired parameter. Example:r PROGRAM

AE Menu2) Press MENU. Selection is complete. TheMenu Screen returns. Repeat the procedure if you wish to set other

function menus.

3) Press MENU. The Menu Screen closes.

Menus with Sub Menusm CAMERA ( pg. 23)q MANUAL( pg. 24)s SYSTEM ( pg. 25)n CAMERA DISPLAY( pg. 26)

t VIDEO ( pg. 26)n VIDEO DISPLAY( pg. 27)1) Press + or to selectthe desired function,and press MENU. TheSub Menu appears. Example: m CAMERA

Menu2) Press + or to select

the desired parameter.3) Press MENU.Selection is complete. Repeat the procedure if

you wish to set otherfunction menus.

4) Press MENU. TheMenu Screen returns. Repeat the procedure if

you wish to set otherfunction menus.

5) Press MENU. The Menu Screen closes.

Changing The Menu Settings

M A

Power Switch

Lock Button

MENU

+

H IDE FA R ETLADE FA R KC.WDE FA R RNPE CWI RENDE WI WOI DP SWI E

ORPE DWI ROPE SWI LL

WBBOIL

OC

R/ F DI PEW A E

UTPE SWI RETH

FOF

PWE

I D OV E

OFONR AT INA R FEC MODRERCA K SBL N H

NRETUR

DU D MSO N EO ST RE EO

Screen for VideoRecording Menu

Screen for VideoPlayback Menu

ERAROGP M A

OR SSP T

OWSN OT ISP

L GHTTWILIGHT

SEPIA MONOTONECLASSIC FILMSTROBE

Selected menu iconblinks.

Selectedparameter

ME ACA R

1 2ODU D MSO N E TIB

2 5O ZO M x FUSNAP SHOT LL

AGI UPGA N C

NRETUR

C MODRE E

Selected menu iconblinks.

Selected function

ME ACA R

C MODRE E

Sub Menu

ME ACA R

1 2ODU D MSO N E TIB

2 5O ZO M x

FU LL

AGI UPGA N C

C MODRE E

NRETUR

SNAP SHOT


23/48

EN 23MENUS FOR DETAILED ADJUSTMENT

CAMERAThe m CAMERA settings are effective whenhe Power Switch is set to both A and M.However, the menu settings can be changed

only when the Power Switch is set to M.] = Factory-preset

SP]: To record in the SP (Standard Play) modeLP: Long Playmore economical, providing 1.5mes the recording time.

NOTES:If the recording mode is switched, the playbackpicture will be blurred at the switching point.It is recommended that tapes recorded in the LPmode on this camcorder be played back on thiscamcorder.During playback of a tape recorded on anothercamcorder, blocks of noise may appear or theremay be momentary pauses in the sound.

12BIT]: Enables video recording of stereoound on four separate channels, and is

ecommended for use when performing AudioDubbing. (Equivalent to the 32 kHz mode ofprevious models)

6BIT: Enables video recording of stereo soundon two separate channels. (Equivalent to the48 kHz mode of previous models)

25X: When set to 25X while using digital zoom,he zoom magnification will reset to 25X since

digital zoom will be disengaged.100X]: Allows you to use the Digital Zoom. By

digitally processing and magnifying images,ooming is possible from 25X (the optical zoommit), to a maximum of 100X digital

magnification.800X: Allows you to use the Digital Zoom. Bydigitally processing and magnifying images,ooming is possible from 25X (the optical zoommit), to a maximum of 800X digital

magnification.

[FULL]: Snapshot mode with no frameNEGA: Nega modePIN-UP: Pin-Up modeFRAME: Snapshot mode with frame

For details on the procedure, refer to Snapshot(For Video Recording) ( pg. 29).

OFF: Allows you to shoot dark scenes with nopicture brightness adjustment.[AGC]: The overall appearance may be grainy,

but the image is bright.AUTO : The shutter speed is automaticallyadjusted. Shooting a subject in low or poorlighting at slow shutter speed provides a brighterimage than in the AGC mode, but the subjectsmovements are not smooth or natural. Theoverall appearance may be grainy. While theshutter speed is being automatically adjusted, is displayed.

Recording Menus

REC MODE

SOUND MODE

ZOOM

SNAP SHOT

GAIN UP

[FULL] PIN-UP FRAMENEGA


24/48

MENUS FOR DETAILED ADJUSTMENT24 ENMANUAL

The q MANUAL settings are effective onlywhen the Power Switch is set to M.[ ] = Factory-preset

OFF: Disables the function.

[ON ]: To compensate for unstable imagescaused by camera-shake, particularly at highmagnification.

NOTES: Accurate stabilization may not be possible if hand

shake is excessive, or depending on the shootingcondition.

The indicator blinks or goes out if theStabilizer cannot be used.

Switch off this mode when recording with thecamcorder on a tripod.

[OFF]: Disables 5-Second Recording.5S: Enables 5-Second Recording. ( pg. 28)Anim.: Allows you to record a few frames only.By using an inanimate object and changing itsposition between shots, you can record thesubject as though it is moving.

[OFF]: Disables the function.ON: When the distance to the subject is lessthan 1 m (3.3 ft), set TELE MACRO to ON.You can shoot a subject as large as possible at adistance of approx. 40 cm (1.4 ft).

NOTE:Depending on the zoom position, the lens may go outof focus.

[OFF]: Records with no change in the screenratio. For playback on a TV with a normal screenratio.CINEMA : Inserts black bands at the top andbottom of the screen. The indicator appears.During playback on wide-screen TVs, the black

bands at the top and bottom of the screen arecut and the screen ratio becomes 16:9. Whenusing this mode, refer to your wide-screen TVsinstruction manual. During playback/recordingon 4:3 TVs/LCD monitor/viewfinder, black bandsare inserted at the top and bottom of the screenand the image appears like a letter boxed 16:9movie.SQUEEZE : For playback on TVs with anaspect ratio of 16:9. Naturally expands the

image to fit the screen without distortion. Theindicator appears. When using this mode,

refer to your wide-screen TVs instructionmanual. During playback/recording on 4:3 TVs/LCD monitor/viewfinder, the image is elongatedvertically.

[OFF]: Disengages the function.ON : Helps cut down on noise created bywind. The indicator appears. The quality ofthe sound will change. This is normal.

DIS

5S

TELE MACRO

WIDE MODE

WIND CUT


25/48

EN 25MENUS FOR DETAILED ADJUSTMENTSYSTEM

The s SYSTEM functions which are set whenhe Power Switch is set to M are also appliedwhen the Power Switch is set to PLAY.

] = Factory-preset

OFF: Even though not heard while shooting,hutter sound is recorded on the tape.

BEEP: The beep sounds when the power isurned on or off, and at the beginning and end ofecording. It also activates the shutter sound

effect. ( pg. 29)MELODY]: Instead of a beep, a melody sounds

when any operation is performed. It alsoactivates the shutter sound effect. ( pg. 29)

OFF: Disables the remote control operations.ON]: Enables the remote control operations.t is recommended that this function be set toOFF to prevent improper operation.

OFF: Automatic demonstration will not takeplace.

ON]: Demonstrates certain functions such asProgram AE with special effects, etc., and canbe used to confirm how these functions operate.Demonstration starts in the following cases:

When the Menu Screen is closed after DEMOMODE is turned ON.With DEMO MODE set to ON, if there is nooperation for about 3 minutes after the PowerSwitch is set to A or M.Performing any operation during thedemonstration stops the demonstration

temporarily. If no operation is performed for morethan 3 minutes after that, the demonstration willresume.

NOTES:If a cassette is in the camcorder, thedemonstration cannot be turned on.DEMO MODE remains ON even if thecamcorder power is turned off.If DEMO MODE remains ON, some functionswill not be available. After viewing demo, set to

OFF.

[LCD]: The image is displayed on the LCDmonitor when the viewfinder is pulled out whilethe LCD monitor is opened.FINDER: The image is displayed in theviewfinder when the viewfinder is pulled outwhile the LCD monitor is opened.

EXECUTE: Resets all settings to the factory-preset.[RETURN]: Does not reset all settings to thefactory-preset.

BEEP

REMOTE

DEMO MODE

PRIORITY

CAM RESET


26/48

MENUS FOR DETAILED ADJUSTMENT26 ENCAMERA DISPLAY

The n (CAMERA DISPLAY) settings areeffective even when the Power Switch is set toA. However, the menu settings can be changedonly when the Power Switch is set to M.

The n (CAMERA DISPLAY) settings exceptBRIGHT are effective only for shooting.

[ ] = Factory-preset

pg. 15, Brightness Adjustment Of TheDisplay

LCD: Keeps the camcorders display (except thedate, time and time code) from appearing on theconnected TV screen.

[LCD/TV]: Makes the camcorders displayappear on screen when the camcorder isconnected to a TV.

OFF: The date/time does not appear.[AUTO]: Displays the date/time for approx. 5seconds when the Power Switch is set fromOFF to A or M.ON: The date/time is always displayed.

[OFF]: Time code is not displayed.ON: Time code is displayed on the camcorderand on the connected TV. Frame numbers arenot displayed during recording. ( pg. 19)

[ENGLISH]/ESPAOLThe language setting can be changed.( pg. 14)

pg. 14, Date/Time Settings

VIDEO[ ] = Factory-preset

SOUND MODE and NARRATIONDuring tape playback, the camcorder detects thesound mode in which the recording was made,and plays the sound back. Select the type ofsound to accompany your playback picture.According to the menu access explanation onpage 22, select SOUND MODE orNARRATION from the Menu Screen and set itto the desired parameter.

[STEREO ]: Sound is output on both L andR channels in stereo.SOUND L : Sound from the L channel isoutput.SOUND R : Sound from the R channel isoutput.

[OFF]: Original sound is output on both L andR channels in stereo.

ON: Dubbed sound is output on both L and Rchannels in stereo.MIX: Original and dubbed sounds are combinedand output in stereo on both L and Rchannels.

Allows you to set the video recording mode (SPor LP) depending on your preference. It isrecommended you use REC MODE in VIDEO

Menu when using this camcorder as a recorderduring dubbing. ( pg. 35, 36)

pg. 20, Blank Search

SYSTEMEach setting is linked with s SYSTEM, whichappears when the Power Switch is set to M.( pg. 22) The parameters are the same as in the

description on page 25.

BRIGHT

ON SCREEN

DATE/TIME

TIME CODE

LANGUAGE

CLOCK ADJ.

Playback Menus

SOUND MODE

NARRATION

REC MODE [SP]/LP

BLANK SRCH


27/48

EN 27MENUS FOR DETAILED ADJUSTMENTVIDEO DISPLAY

The n (VIDEO DISPLAY) settings areeffective only for video playback exceptBRIGHT.The parameters (except OFF in ON SCREENsettings) are the same as in the description(CAMERA DISPLAY) on page 26.

] = Factory-preset

pg. 15, Brightness Adjustment Of TheDisplay

When set to OFF, the camcorders displaydisappears.

When set to AUTO, the date/time are displayedn the following cases:

When playback starts. The camcorder displaysthe date/time when scenes are recorded.When the date is changed during playback.

pg. 19, Time Code

ENGLISH]/ESPAOLThe language setting can be changed. pg. 14)

BRIGHT

ON SCREEN OFF/[LCD]/LCD/TV

DATE/TIME [OFF]/AUTO/ON

TIME CODE [OFF]/ON

LANGUAGE


28/48

28 EN FEATURES FOR RECORDING

Record a vacation or an important event in 5-second clips to keep the action moving. Thisfunction is available only for video recording.

1 Set 5S to 5S. ( pg. 24)

The 5S indicator appears.2 Press the Recording Start/Stop Button tostart recording, and after 5 seconds thecamcorder enters Record-Standby modeautomatically. Even if you press the Recording Start/Stop Button

again within 5 seconds after recording starts,Record-Standby mode is not engaged.

3 To exit the 5S mode, select OFF in step 1.

To take a snapshot in the 5-second recordingmodeInstead of pressing the Recording Start/StopButton in step 2, select the desired Snapshotmode in CAMERA Menu ( pg. 23), then pressSNAPSHOT. The camcorder records a 5-second still. When 5S is set to Anim., thisfunction is not available.

NOTE:When 5S is set to Anim., the 5-Second

Recording mode is not available. Animationrecording of a few frames only is taken instead.

Makes dark subjects or areas even brighter thanthey would be under good natural lighting.Although the recorded image is not grainy, it maylook as if it is strobing due to the slow shutterspeed.

1 Set the Power Switch to M.

2 Press NIGHT so that the Night-Alive indicator appears. The shutter speed is automatically adjusted to

provide up to 30 times sensitivity. appears beside while the shutter speed

is being automatically adjusted.

To deactivate Night-AlivePress NIGHT again so that the Night-Aliveindicator disappears.

NOTES: During Night-Alive, the following functions or

settings cannot be activated and its indicatorblinks or goes out: Some modes of Program AE With Special

Effects ( pg. 34). GAIN UP in CAMERA Menu ( pg. 23). DIS in MANUAL Menu ( pg. 24).

During Night-Alive, it may be difficult to bring thecamcorder into focus. To prevent this, use of atripod is recommended.

5-Second Recording Night-Alive


29/48

EN 29FEATURES FOR RECORDING

This feature lets you record still images that lookke photographs onto a tape.


2 Set SNAP SHOT to the desired mode. pg. 22, 23)

3 Press SNAPSHOT.There is the sound effect of a shutter closing.The O indication appears and a still imagewill be recorded for approx. 6 seconds, then thecamcorder re-enters the Record-Standby mode.You can perform Snapshot also during recording.A still image will be recorded for approx.6 seconds, then the normal recording resumes.Regardless of the Power Switch position (A or

M), Snapshot recording takes place using theselected Snapshot mode.

Motor Drive ModeKeeping SNAPSHOT pressed in step 3providesan effect similar to serial photography. (Intervalbetween still images: approx. 1 second)

The camcorders Full Range AF system offerscontinuous shooting ability from close-up (asclose as approx. 5 cm (2") to the subject) toinfinity.However, correct focus may not be obtained

depending on the shooting condition. In thiscase, use the manual focus mode.

1 Set the Power Switch toM.

2 Press FOCUS. Themanual focus indicatorappears.

3 Press + or to focus on

a subject. When the focus levelcannot be adjusted anyfurther or closer, or will blink.

4 Press MENU. Focus adjustment is complete.

To reset to Auto FocusPress FOCUS twice or set the Power Switch toA.

Manual focus is recommended in situations

listed below. When two subjects overlap in the same scene. When illumination is low.* When the subject has no contrast (difference in

brightness and darkness), such as a flat, one-color wall, or a clear, blue sky.*

When a dark object is barely visible in the LCDmonitor or the viewfinder.*

When the scene contains minute patterns oridentical patterns that are regularly repeated.

When the scene is affected by sunbeams or light

reflecting off the surface of a body of water. When shooting a scene with a high-contrast

background.* The following low-contrast warnings appear

blinking: , , and .

Snapshot (For Video Recording) Manual Focus

Manual focusindicator


30/48

FEATURES FOR RECORDING30 EN

Manual exposure control is recommended in thefollowing situations:When shooting using reverse lighting or when the

background is too bright.When shooting on a reflective natural background

such as at the beach or when skiing.When the background is overly dark or the subject

is bright.


2 Set p to MANUAL. ( pg. 22) The exposure control indicator appears.

3 To brighten the image, press +. To darken theimage, press . (maximum 6) +3 exposure has the same effect as the backlight

compensation. ( pg. 31) 3 exposure has the same effect as when r is

set to SPOTLIGHT. ( pg. 34)

4 Press MENU. Exposure adjustment iscomplete.

To return to automatic exposure controlSelect AUTO in step 2. Or, set the PowerSwitch to A.

NOTES: You cannot use the manual exposure control at

the same time when r is set to SPOTLIGHTor SNOW ( pg. 34), or with the backlightcompensation.

If the adjustment does not cause any visiblechange in brightness, set GAIN UP to AUTO.( pg. 22, 23)

Like the pupil of the human eye, the iriscontracts in well-lit environments to keep toomuch light from entering, and dilates in dimenvironments to allow in more light.Use this function in the following situations:

When shooting a moving subject.When the distance to the subject changes (so its

size in the LCD monitor or the viewfinderchanges), such as when the subject is backingaway.

When shooting on a reflective natural backgroundsuch as at the beach or when skiing.

When shooting objects under a spotlight.When zooming.


2 Set p to MANUAL. ( pg. 22) The exposure control indicator appears.

3 Adjust zoom so that the subject fills the LCDmonitor or the viewfinder, then press and holdMENU for over 2 seconds. The exposure controlindicator and the indication appear.

4 Press MENU. The indication changes to and the iris is locked.

To return to automatic iris controlSelect AUTO in step 2. Or, set the PowerSwitch to A. The exposure control indicator and

disappear.

To lock the exposure control and the irisAfter step 2, adjust the exposure by pressing +or . Then lock the iris in steps 3 and 4. Forautomatic locking, select AUTO in step 2. Theexposure control and the iris become automatic.

Exposure Control Iris Lock


31/48


Backlight compensation brightens the subjectquickly.With simple operation, backlight compensationeature brightens the dark subject portion byncreasing the exposure.


2 Press BACK LIGHT so that the BacklightCompensation indicator appears.

To cancel Backlight CompensationPress BACK LIGHT twice so that the ndicator disappears.

NOTE:Using Backlight Compensation may cause the light

around the subject to become too bright and theubject to become white.

Selection of a spot metering area enables moreprecise exposure compensation. You can selectone of the three metering areas on the LCDmonitor/viewfinder.

1 Set the Power Switch to M.2 Press BACK LIGHT twice so that the SpotExposure Control indicator appears.A spot metering area frame appears at the

centre of the LCD monitor/viewfinder.

3 Press + or to select the desired spotmetering area frame.

4 Press MENU.Spot Exposure Control is engaged.

Exposure is adjusted to make the brightness ofthe selected area most appropriate.

To lock the irisAfter step 3, press and hold MENU over 2seconds. The indication appears and theiris is locked.

To cancel Spot Exposure ControlPress BACK LIGHT once so that the indicator disappears.

NOTES: You cannot use the Spot Exposure Control at the

same time with following functions. SQUEEZE in WIDE MODE ( pg. 24) STROBE in PROGRAM AE ( pg. 34)Digital Zoom ( pg. 18)Manual Exposure Control

Depending on the shooting location and condition,optimum result may not be attained.

Backlight Compensation Spot Exposure Control


32/48


The white balance refers to the correctness ofcolor reproduction under various lighting. If thewhite balance is correct, all other colors will beaccurately reproduced.The white balance is usually adjusted

automatically. However, more advancedcamcorder operators control this functionmanually to achieve a more professional color/tint reproduction.

To change the settingSet u to the desired mode. ( pg. 22) The selected mode indicator except AUTO

appears.

[AUTO]: White balance is adjusted

automatically.MWB: Adjust the white balance manually

when shooting under various types of lighting.( Manual White Balance Adjustment)

FINE: Outdoors on a sunny day.CLOUD: Outdoors on a cloudy day.HALOGEN: A video light or similar type of

lighting is used.[ ] = Factory-preset

To return to automatic white balanceSet u to AUTO. ( pg. 22)Or, set the Power Switch to A.

Adjust the white balancemanually when shootingunder various types oflighting.

1 Set the Power Switchto M.

2 Select MWB inuW.BALANCE menu. ( pg. 22) The indication blinks slowly.

3 Hold a sheet of plain white paper in front ofthe subject. Adjust zoom or position yourself sothat the white paper fills the screen.

4 Press and hold MENU until begins

blinking rapidly.When the setting is completed, resumes

normal blinking.

5 Press MENU twice. The Menu Screen closesand the Manual White Balance indicator isdisplayed.

NOTES: In step 3, it may be difficult to focus on the white

paper. In such a case, adjust focus manually.( pg. 29)

A subject can be shot under various types oflighting conditions indoors (natural, fluorescent,candlelight, etc.). Because the color temperatureis different depending on the light source, thesubject tint will differ depending on the whitebalance settings. Use this function for a morenatural result.

Once you adjust white balance manually, thesetting is retained even if the power is turned off orthe battery removed.

White Balance Adjustment Manual White Balance Adjustment

White paper


33/48


These effects let you make pro-style sceneransitions. Use them to spice up the transitionrom one scene to the next.

Wipe or Fader works when video recording istarted or stopped.

1 Set the Power Switch to M.2 Set v to the desired mode. ( pg. 22)

The WIPE/FADER menu disappears and theeffect is reserved.The selected effect indicator appears.

3 Press the Recording Start/Stop Button toactivate the Fade-in/out or Wipe-in/out.

To deactivate the selected effect

Select OFF in step 2. The effect indicatordisappears.

NOTES:You can extend the length of a Wipe or Fader bypressing and holding the Recording Start/StopButton.Some Wipe/Fader Effects cannot be used withcertain modes of Program AE with special effects.( pg. 34) In this case, the selected indicatorblinks or goes out.

WIPE/FADER

OFF: Disables the function. (Factory-preset)

FADERWHITE: Fade in or out with a whitecreen.

FADERBLACK: Fade in or out with a blackcreen.

FADERB.W: Fade in to a color screen

rom a black and white screen, or fade out fromolor to black and white.

WIPECORNER: Wipe in on a black screenrom the upper right to the lower left corner, or

wipe out from lower left to upper right, leaving ablack screen.

WIPEWINDOW: The scene starts in theentre of a black screen and wipes in toward theorners, or comes in from the corners, gradually

wiping out to the centre.WIPESLIDE: Wipe in from right to left, or

wipe out from left to right.

WIPEDOOR: Wipe in as the two halves ofa black screen open to the left and right,evealing the scene, or wipe out and the blackcreen reappears from left and right to cover thecene.

WIPESCROLL: The scene wipes in fromthe bottom to the top of a black screen, or wipesout from top to bottom, leaving a black screen.

WIPESHUTTER: Wipe in from the centreof a black screen toward the top and bottom, orwipe out from the top and bottom toward thecentre leaving a black screen.

Wipe Or Fader Effects


34/48



2 Set r to the desired mode. ( pg. 22) The PROGRAM AE menu disappears and the

selected effect is activated. The selected effect indicator appears.

To deactivate the selected effectSelect OFF in step 2. The effect indicatordisappears.

NOTES: Program AE with special effects can be changed

during recording or during Record-Standby. Some modes of Program AE with special effects

cannot be used during Night-Alive.When a subject is too bright or reflective, a vertical

streak may appear (smear phenomenon). Smearphenomenon tends to occur when SPORTS orany mode of SHUTTER 1/250 1/4000 isselected.

Some modes of Program AE with special effectscannot be used with certain Wipe/Fader effects.( pg. 33) In this case, the selected indicatorblinks or goes out.

PROGRAM AE

OFF: Disables the function. (Factory-preset)

SHUTTER 1/60: The shutter speed is fixedat 1/60th of a second. Black bands that usuallyappear when shooting a TV screen becomenarrower.

SHUTTER 1/100: The shutter speed isfixed at 1/100th of a second. The flickering thatoccurs when shooting under a fluorescent lightor mercury-vapour lamp is reduced.

SHUTTER 1/250/ SHUTTER 1/500/SHUTTER 1/1000/ SHUTTER 1/2000/SHUTTER 1/4000: These settings allow fast-moving images to be captured one frame at atime, for vivid, stable slow-motion playback byfixing shutter speed variables. Use thesesettings when an automatic adjustment does notwork well, using SPORTS mode. The faster theshutter speed, the darker the picture becomes.Use the shutter function under good lighting

conditions.

SPORTS(Variable Shutter Speed: 1/250 1/4000):This setting allows fast-moving images to becaptured one frame at a time, for vivid, stableslow-motion playback. The faster the shutterspeed, the darker the picture becomes. Use theshutter function under good lighting conditions.

SNOW: Compensates for subjects that mayotherwise appear too dark when shooting inextremely bright surroundings such as in thesnow.

SPOTLIGHT: Compensates for subjectsthat may otherwise appear too bright whenshooting under extremely strong direct lightingsuch as spotlights.

TWILIGHT: Makes evening scenes lookmore natural. White Balance ( pg. 32) is

automatically set to , but can be changed toyour desired setting. When Twilight is chosen,the camcorder automatically adjusts the focusfrom approx. 10 m (32 ft) to infinity. From lessthan 10 m, adjust the focus manually.

SEPIA: Recorded scenes have a brownishtint like old photos. Combine this with theCinema mode ( pg. 24, WIDE MODE ) for aclassic look.

MONOTONE: Like classic black and whitefilms, your footage is shot in B/W. Used togetherwith the Cinema mode ( pg. 24, WIDEMODE ), it enhances the classic film effect.

CLASSIC FILM: Gives recorded scenes astrobe effect.

STROBE: Your recording looks like a seriesof consecutive snapshots.

MIRROR: Creates a mirror image on theright half of the screen, juxtaposed to the normalimage on the other half.

Program AE With Special Effects


35/48

EN 35EDITING

A Yellow to VIDEO INB Red to AUDIO R INC White to AUDIO L IN

1 Following the illustrations, connect thecamcorder and the VCRs input connectors.

2 Start playback on the camcorder. ( pg. 20)

3 At the point you want to start dubbing, startrecording on the VCR. (Refer to the VCRsinstruction manual.)

4To stop dubbing, stop recording on the VCR,then stop playback on the camcorder.


the power supply instead of the battery pack.( pg. 13)

To choose whether or not the following displaysappear on the connected TVDate/time

Set DATE/TIME to AUTO, ON or OFF.

(

pg. 22, 27)Time code

Set TIME CODE to OFF or ON.( pg. 22, 27)

Indications other than date/time and time codeSet ON SCREEN to OFF, LCD or LCD/TV. ( pg. 22, 27)

Dubbing To A VCR

21 3TV

VCR

Open the cover.Audio/Videocable

(provided)

To AV connector


36/48

EDITING36 EN

It is also possible to copy recorded scenes fromthe camcorder onto another video unit equippedwith a DV connector. Since a digital signal issent, there is little if any image or sounddeterioration.

To use this camcorder as a player


2 Connect this camcorder to a video unitequipped with a DV input connector using a DVcable as shown in the illustration.

3Start playback on the camcorder. (

pg. 20)4 At the point you want to start dubbing, startrecording on the video unit. (Refer to the videounits instruction manual.)

5 To stop dubbing, stop recording on the videounit, then stop playback on this camcorder.


the power supply instead of the battery pack.( pg. 13)

If a blank portion or disturbed image is playedback on the player during dubbing, the dubbingmay stop so that an unusual image is not dubbed.

Even though the DV cable is connected correctly,sometimes the image may not appear in step 4. Ifthis occurs, turn off the power and makeconnections again.

When using a DV cable, be sure to use theoptional JVC VC-VDV204U DV cable.

To use this camcorder as a recorder


2 Connect this camcorder to a video unit

equipped with a DV output connector using a DVcable as shown in the illustration.

3 Set REC MODE to SP or LP. ( pg. 23)4 Set the camcorders Power Switch to PLAY.

5 Press the Recording Start/Stop Button toengage the Record-Pause mode. The indication appears on the screen.

6 Start playback on the player.7 At the point you want to start dubbing, pressthe Recording Start/Stop Button to startdubbing. The indication rotates.

8 Press the Recording Start/Stop Button againto stop dubbing. The indication stopsrotating.

9 Press 8 to return to the normal playbackmode.

NOTE:

Digital Dubbing is performed in the sound moderecorded on the original tape, regardless of thecurrent SOUND MODE setting. ( pg. 23)

Dubbing To Or From A Video UnitEquipped With A DV Connector(Digital Dubbing)

Core filter

To DV IN/OUT

DV cable (optional)

To DV IN/OUT

Video unit equipped with DV connector

DV IN


37/48


38/48

38 EN TROUBLESHOOTINGIf, after following the steps in the chart below, theproblem still exists, please consult your nearestJVC dealer.

Power

The power is not connected properly.

HConnect the AC Adapter securely. (

pg. 13) The battery pack is not attached firmly.HDetach the battery pack once again and re-attach

it firmly. ( pg. 11) The battery is dead.HReplace the dead battery with a fully charged

one. ( pg. 11)

Video Recording

The tapes erase protection tab is set to SAVE.HSet the tapes erase protection tab to REC.

( pg. 16) TAPE END appears.HReplace with new cassette. ( pg. 16) The cassette holder cover is open.HClose the cassette holder cover.

This is not a malfunction.

This is not a malfunction.

DATE/TIME is set to OFF.HSet DATE/TIME to ON. ( pg. 22, 26)

Certain Wipe/Fader effects, certain modes ofProgram AE with special effects, DIS and otherfunctions that cannot be used together areselected at the same time.HRe-read the sections covering Wipe/Fader

effects, Program AE with special effects andDIS. ( pg. 22, 24, 33, 34)

25X optical zoom is selected.HSet ZOOM to 100X or 800X. ( pg. 23)

Video Playback

Your TV has AV input terminals, but is not set toits VIDEO mode.HSet the TV to the mode or channel appropriate for

video playback. ( pg. 21) The cassette holder cover is open.HClose the cassette holder cover. ( pg. 16)

HClean the video heads with an optional cleaningcassette. ( pg. 44)

Advanced features

Focus is set to the Manual mode.HSet Focus to the Auto mode. ( pg. 29) The lens is dirty or covered with condensation.HClean the lens and check the focus again.

( pg. 42)

The 5-Second mode is set to Anim. in MANUALMenu.HSet 5S to 5S in MANUAL Menu.

( pg. 22, 28)

The Squeeze mode (SQUEEZE) is selected.HDisengage the Squeeze (SQUEEZE) mode.

( pg. 22, 24)

The camcorder is a microcomputer-controlleddevice. External noise and interference (from aTV, a radio, etc.) might prevent it fromfunctioning properly. In such cases, first

disconnect its power supply unit (battery pack,AC Adapter, etc.) and wait a few minutes; andthen re-connect it and proceed as usual fromthe beginning.

No power is supplied.

Recording cannot be performed.

When shooting a subject illuminated bybright light, vertical lines appear.

When the screen is under direct sunlightduring shooting, the screen becomes red orblack for an instant.

During recording, the date/ time does notappear.

The LCD monitor or viewfinder indicationsblink.

Digital Zoom does not work.

The tape is moving, but there is no picture.

Blocks of noise appear during playback, orthere is no playback picture and the screenbecomes blue.

The focus does not adjust automatically.

In the 5-Second mode, recording endsbefore 5 seconds have elapsed.

Snapshot mode cannot be used.


39/48

EN 39TROUBLESHOOTING

The light source or the subject does not includewhite. Or there are various different light sourcesbehind the subject.HFind a white subject and compose your shot so

that it also appears in the frame. ( pg. 29)

Shooting was performed under backlit conditions.HPress BACK LIGHT. ( pg. 31)

The subject is too bright.HSet r to SPOTLIGHT. ( pg. 34)

The Sepia (SEPIA) or Monotone (MONOTONE)mode is activated.HDisengage the Sepia (SEPIA) or Monotone

(MONOTONE) mode before setting WhiteBalance. ( pg. 34)

The Sepia (SEPIA) or Monotone (MONOTONE)mode is activated.

HDisengage the Sepia (SEPIA) and Monotone(MONOTONE). ( pg. 34)

When shooting in the dark, the unit becomeshighly sensitive to light when GAIN UP is set toAUTO.H If you want the lighting to look more natural, set

GAIN UP to AGC or OFF. ( pg. 22, 23)

Other problems

Charging is difficult in places subject to extremelyhigh/low temperatures.HTo protect the battery, it is recommended to

charge it in places with a temperature of 10C to35C (50F to 90F). ( pg. 43)

The battery pack is not attached firmly.HDetach the battery pack once again and re-attach

it firmly. ( pg. 11)

The date/time is not set.HSet the date/time. ( pg. 14) The built-in clock battery has run out and the

previously set date/time has been erased.HConsult your nearest JVC dealer for replacement.

This is not a malfunction.HBy recording with DIS activated ( pg. 22, 24)

this can be avoided.

The DV cable was plugged/unplugged with powerturned on.HTurn the camcorders power off and on again,

then operate it.

In places subject to low temperature, imagesbecome dark due to the characteristics of theLCD monitor. This is not a malfunction.

HAdjust the brightness and angle of the LCDmonitor. ( pg. 15, 18)

When the LCD monitors fluorescent light reachesthe end of its service life, images on the LCDmonitor become dark.HConsult your nearest JVC dealer.

The LCD monitor and the viewfinder are made

with high-precision technology. However, blackspots or bright spots of light (red, green or blue)may appear constantly on the LCD monitor or theviewfinder. These spots are not recorded on thetape. This is not due to any defect of the unit.(Effective dots: more than 99.99 %)

The batterys charge is low.H Install a fully charged battery. ( pg. 11)

The color of Snapshot looks strange.

The image taken using Snapshot is toodark.

The image taken using Snapshot is toobright.

White Balance cannot be activated.

The Black & White Fader does not work.

The image looks like the shutter speed istoo slow.

The POWER/CHARGE lamp on thecamcorder does not light during charging.

SET DATE/TIME! appears.

When the image is printed from the printer,a black bar appears at the bottom of thescreen.

When the camcorder is connected via theDV connector, the camcorder does notoperate.

Images on the LCD monitor appear dark orwhitish.

Colored bright spots appear all over theLCD monitor or the viewfinder.

The cassette will not load properly.


40/48

TROUBLESHOOTING40 EN

The viewfinder is pulled out and PRIORITY isset to FINDER.HPush the viewfinder back in or set PRIORITY to

LCD. ( pg. 18, 22, 25) The LCD monitors brightness setting is too dark.

HAdjust the brightness of the LCD monitor.( pg. 15)H If the monitor is tilted upward 180 degrees, open

the monitor fully. ( pg. 18)

A malfunction of some kind has occurred. In thiscase the camcorders functions becomeunusable.H pg. 41.

Warning Indications

Displays the battery remaining power.Remaining power level

As the battery power comes close to nil, thebattery remaining power indicator blinks.When the battery power is exhausted, powerturns off automatically.

Appears when no tape is loaded. ( pg. 16)

Appears when the erase protection tab is set toSAVE while the Power Switch is set to A orM. ( pg. 13)

Appears if dirt is detected on the heads duringrecording. Use an optional cleaning cassette.( pg. 44)

Appears if condensation occurs. When thisindication is displayed, wait more than 1 houruntil condensation disappears.

Appears if a tape is not loaded when theRecording Start/Stop Button or SNAPSHOTButton is pressed while the Power Switch is setto A or M.

Appears when the tape ends during recording orplayback.

Appears when the date/time is not set.( pg. 14)The built-in clock battery has run out and the

previously set date/time has been erased.Consult your nearest JVC dealer forreplacement.

Picture does not appear on the LCDmonitor.

An error indication (01 04 or 06) appears.

CHECK TAPES ERASE PROTECTION TAB

USE CLEANING CASSETTE

CONDENSATION, OPERATION

PAUSED PLEASE WAIT

TAPE!

TAPE END

SET DATE/TIME!

ExhaustedHigh


41/48

EN 41TROUBLESHOOTING

Appears for 5 seconds after power is turned on ifhe lens cap is attached or when it is dark.

Appears when pictures recorded in the HDVormat are detected. The pictures in the HDVormat cannot be played back with thisamcorder.

The error indications (01, 02 or 06) show whatype of malfunction has occurred. When an errorndication appears, the camcorder turns offautomatically. Remove the power supply

battery, etc.) and wait a few minutes for thendication to clear. When it does, you canesume using the camcorder. If the indicationemains, consult your nearest JVC dealer.

The error indications (03 or 04) show what typeof malfunction has occurred. When an errorndication appears, the camcorder turns off

automatically. Eject the cassette once and re-nsert it, then check if the indication clears.When it does, you can resume using theamcorder. If the indication remains, consultour nearest JVC dealer.

LENS CAP

HDV

UNIT IN SAFEGUARD MODEREMOVE AND REATTACH BATTERY

UNIT IN SAFEGUARD MODEEJECT AND REINSERT TAPE


42/48

42 EN USER MAINTENANCE

Before cleaning, turn off the camcorder andremove the battery pack and AC Adapter.

To clean the exteriorWipe gently with a soft cloth. Put the cloth in

diluted mild soap and wring it well to wipe offheavy dirt. Then wipe again with a dry cloth.

To clean the LCD monitorWipe gently with a soft cloth. Be careful not todamage the monitor. Close the LCD monitor.

To clean the lensBlow it with a blower brush, then wipe gentlywith lens cleaning paper.

NOTES: Avoid using strong cleaning agents such as

benzine or alcohol. Cleaning should be done only after the battery

pack has been removed or other power units havebeen disconnected.

Mould may form if the lens is left dirty.When using a cleaner or chemically treated cloth

refer to the cautions of each product. To clean the viewfinder, please consult your

nearest JVC dealer.

Cleaning The Camcorder


43/48

EN 43CAUTIONS

AC AdapterWhen using the AC Adapter in areas other thanhe USA

The provided AC Adapter features automaticvoltage selection in the AC range from 110 V to240 V.

USING HOUSEHOLD AC PLUG ADAPTERn case of connecting the units power cord to anAC wall outlet other than American NationalStandard C73 series type use an AC plug adapter,alled a Siemens Plug, as shown.

For this AC plug adapter, consult your nearest JVCdealer.

Battery PacksThe supplied batterypack is a lithium-ionbattery. Before using theupplied battery pack or

an optional battery pack,be sure to read theollowing cautions: To avoid hazards..do not burn...do not short-circuit the terminals. When

transporting, make sure the provided battery capis attached to the battery. If the battery cap ismisplaced, carry the battery in a plastic bag.

..do not modify or disassemble.

..do not expose the battery to temperaturesexceeding 60C (140F), as this may cause thebattery to overheat, explode or catch fire.

..use only specified chargers. To prevent damage and prolong service

life..do not subject to unnecessary shock...charge in an environment where temperatures

are within the tolerances shown in the chartbelow. This is a chemical reaction type battery cooler temperatures impede chemical reaction,while warmer temperatures can preventcomplete charging.

..store in a cool, dry place. Extended exposure tohigh temperatures will increase natural dischargeand shorten service life.

..fully charge and then fully discharge the batteryevery 6 months when storing the battery packover a long period time.

... remove from charger or powered unit when not inuse, as some machines use current even whenswitched off.

NOTES: It is normal for the battery pack to be warm after

charging, or after use.Temperature Range Specifications

Charging: 10C to 35C (50F to 95F)Operation: 0C to 40C (32F to 104F)Storage: 20C to 50C (4F to 122F)

The lower the temperature, the longer rechargingtakes.

Charging times are for a fully discharged batterypack.

CassettesTo properly use and store your cassettes, be

sure to read the following cautions: During use...make sure the cassette bears the Mini DV mark....be aware that recording onto prerecorded tapes

automatically erases the previously recordedvideo and audio signals.

...make sure the cassette is positioned properlywhen inserting.

...do not load and unload the cassette repeatedlywithout allowing the tape to run at all. Thisslackens the tape and can result in damage.

...do not open the front tape cover. This exposesthe tape to fingerprints and dust.

Store cassettes...away from heaters or other heat sources....out of direct sunlight....where they wont be subject to unnecessary

shock or vibration....where they wont be exposed to strong magnetic

fields (such as those generated by motors,transformers or magnets).

...vertically, in their original cases.

Plug adapter

Terminals

The Benefits Of Lithium-Ion BatteriesLithium-ion battery packs are small but have alarge power capacity. However, when one isexposed to cold temperatures (below 10C/

50F), its usage time becomes shorter and itmay cease to function. If this happens, placethe battery pack in your pocket or other warm,protected place for a short time, then re-attach it to the camcorder.


44/48

CAUTIONS44 ENLCD Monitor To prevent damage to the LCD monitor, DO

NOT...push it strongly or apply any shocks....place the camcorder with the LCD monitor on the

bottom. To prolong service life...avoid rubbing it with coarse cloth. Be aware of the following phenomena for

LCD monitor use. These are notmalfunctions

...While using the camcorder, the surface aroundthe LCD monitor and/or the back of the LCDmonitor may heat up.

... If you leave power on for a long time, the surfacearound the LCD monitor becomes hot.

Main Unit For safety, DO NOT...open the camcorders chassis....disassemble or modify the unit....short-circuit the terminals of the battery pack.

Keep it away from metallic objects when not inuse.

...allow inflammables, water or metallic objects toenter the unit.

... remove the battery pack or disconnect the power

supply while the power is on.... leave the battery pack attached when thecamcorder is not in use.

Avoid using the unit...in places subject to excessive humidity or dust.... in places subject to soot or steam such as near

JVC-GRD250 Camcorder Manual

Documents

Transcript of JVC-GRD250 Camcorder Manual