* eDP Connector (on the Backside of PCB)

15 : Backlight Control Level (CON_LBKLT_CTL) (BLT_PWM1) 1-2: From eDP PWM to CON_LBKLT_CTL 2-3: From LVDS PWM to CON_LBKLT_CTL

16 : Panel Power Select (LCD_VCC) (PNL_PWR1) 1-2: LCD_VCC: +3V 2-3: LCD_VCC: +5V 4-5: LCD_VCC: +12V

17 : Backlight Volume Control (BLT_VOL1)

18 : SATA Power Output Connector

19 : USB2.0 Headers (USB2_11_12, USB2_8_9) (USB2_11_12 is for IMB-1222 / IMB-1222-WV / IMB-X1222-WV Only)

20 : CPU FAN Connector (+12V)

11 : COM Port PWR Setting Jumpers PWR_COM1 (For COM Port1) PWR_COM2 (For COM Port2) PWR_COM3 (For COM Port3) PWR_COM4 (For COM Port4) 1-2: +5V 2-3: +12V

12 : Backlight Power Select (LCD_BLT_VCC) (BKT_PWR1) 1-2: LCD_BLT_VCC: +5V 2-3: LCD_BLT_VCC: +12V 4-5: LCD_BLT_VCC: DC_IN

13 : Inverter Power Control Wafer (BLT_PWR1)

14* : LVDS Panel Connector

1 : USB3.2 Gen1 Header (USB3_3_4)

2 : Battery Connector4 : MCU Connector

5 : LPC Header (For IMB-1222 / IMB-1222-WV / IMB-X1222-WV Only)

6 : SATA3 Connectors (SATA3_1, SATA3_2)

7 : Digital Input / Output Default Value Setting (JGPIO_SET1) 1-2: Pull-High 2-3: Pull-Low

8 : Digital Input / Output Power Select (JGPIO_PWR1) 1-2: +12V 2-3: +5V

9 : Digital Input/Output Pin Header (JGPIO1)

10 : COM Port Headers (COM1, 2, 3, 4)

Jumpers and Headers Setting Guide

IMB-1222IMB-1222-WVIMB-1223IMB-1223-WVIMB-X1222-WV PIN Signal Name1 NA

2 GND

3 eDP_TX#3_CON

4 eDP_TX3_CON

5 GND

6 eDP_TX#2_CON

7 eDP_TX2_CON

8 GND

9 eDP_TX#1_CON

10 eDP_TX1_CON

11 GND

12 eDP_TX#0_CON

13 eDP_TX0_CON

14 GND

15 eDP_AUX_CON

16 eDP_AUX#_CON

17 GND

18 LCD_VCC

19 LCD_VCC

20 LCD_VCC

21 LCD_VCC

22 NA

23 GND

24 GND

25 GND

26 GND

27 eDP_HPD_CON

28 GND

29 GND

30 GND

31 GND

32 CON_LBKLT_EN

33 CON_LBKLT_CTL

34 SMB_DATA

35 SMB_CLK

36 LCD_BLT_VCC

37 LCD_BLT_VCC

38 LCD_BLT_VCC

39 LCD_BLT_VCC

40 NA

The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

PIN Signal Name PINSignal Name PIN

Signal Name PIN

Signal Name PIN

Signal Name

1 DDCD# 3 TTXD 5 GND 7 RRTS# 9 PWR2 RRXD 4 DDTR# 6 DDSR# 8 CCTS#

2

1

PIN RS232 RS422 RS4851 DCD TX- RTX-2 RXD RX+ N/A3 TXD TX+ RTX+4 DTR RX- N/A5 GND GND GND6 DSR N/A N/A7 RTS N/A N/A8 CTS N/A N/A9 PWR PWR PWR

* This motherboard supports RS232/422/485 on COM1, 2 ports. Please refer to below table for the pin definition. In addition, COM1, 2 ports (RS232/422/485) can be adjusted in BIOS setup utility > Advanced Screen > Super IO Configuration. You may refer to our user manual for details.

1

IntA_PB_D+

Dummy

IntA_PB_D-

GND

IntA_PB_SSTX+

GND

IntA_PB_SSTX-

IntA_PB_SSRX+

IntA_PB_SSRX-

VbusVbus

Vbus

IntA_PA_SSRX-

IntA_PA_SSRX+

GND

IntA_PA_SSTX-

IntA_PA_SSTX+

GND

IntA_PA_D-

IntA_PA_D+

1

GN

D

SM

B_

DA

TA

_M

AIN

LA

D2

LA

D1

GN

D

S_

PW

RD

WN

#

SE

RIR

Q#

GN

D

PC

ICLK

PC

IRST#

LA

D3

+3

V

LA

D0

+3

VSB

GN

D

FR

AM

ESM

B_

CLK

_M

AIN

PIN Signal Name PINSignal Name PIN

Signal Name PIN

Signal Name PIN

Signal Name

2 SIO_GP71 4SIO_GP72 6

SIO_GP73 8

SIO_GP74 10 GND

1 SIO_GP75 3SIO_GP76 5

SIO_GP77 7

SIO_GP80 9

JGPIO_PWR

COM1, 2 Port Pin Definition

1

PIN Signal Name6 LCD_BLT_VCC

5 LCD_BLT_VCC

4 CON_LBKLT_EN

3 CON_LBKLT_CTL

2 GND

1 GND

* PD (Panel Detection): Connect this pin to LVDS Panel’s Ground pin to detect Panel detection.

1

39 40

2

PIN Signal Name PIN Signal Name39 LCD_BLT_VCC 40 LCD_BLT_VCC

37 CON_LBKLT_CTL 38 LCD_BLT_VCC

35 GND 36 CON_LBKLT_EN

33 LVDS_B_CLK# 34 LVDS_B_CLK

31 LVDS_B_DATA3 32 GND

29 DPLVDD_EN 30 LVDS_B_DATA3#

27 LVDS_B_DATA2# 28 LVDS_B_DATA2

25 LVDS_B_DATA1 26 GND

23 GND 24 LVDS_B_DATA1#

21 LVDS_B_DATA0# 22 LVDS_B_DATA0

19 LVDS_A_CLK 20 GND

17 GND 18 LVDS_A_CLK#

15 LVDS_A_DATA3# 16 LVDS_A_DATA3

13 LVDS_A_DATA2 14 GND

11 GND 12 LVDS_A_DATA2#

9 LVDS_A_DATA1# 10 LVDS_A_DATA1

7 LVDS_A_DATA0 8 PD (Panel Detection)

5 LDDC_DATA 6 LVDS_A_DATA0#

3 +3.3V 4 LDDC_CLK

1 LCD_VCC 2 LCD_VCC

1

PIN Signal Name PINSignal Name PIN

Signal Name PIN

Signal Name PIN

Signal Name PIN

Signal Name PIN

Signal Name

7 GND 6 GND 5 BLT_DW 4 BLT_UP 3 PWRDN 2 GPIO_VOL_DW 1GPIO_

VOL_UP

GND

+5V

+12V

1

GND

FAN_SPEED

FAN_SPEED_CONTROL

+12V

GND

4

2

3

1

EDP1

40

1

P/ N: 15G06M090000AK V1.0*15G06M090000AK*

34 : SPDIF Header

35 : DC Jack (DC_JACK1) 36 : Audio Jack: Pink - Mic In38 : Audio Jack: Green - Line Out

37 : Front Panel Audio Header

39 : 3W Audio AMP Output Wafer

40 : RJ45 LAN Port (LAN2)42 : RJ45 LAN Port (LAN1)

41 : VGA Header (For IMB-1223 / IMB-1223-WV Only)

43 : DisplayPort (DISPLAY3) (For IMB-1222 / IMB-1222-WV / IMB-X1222-WV Only)

44 : ThunderBolt Header

45 : Top: DisplayPort (DP2) Bottom: HDMI Port (HDMI1)46 : USB3.2 Gen1 Ports (USB_5_6) (IMB-1222 / IMB-1222-WV / IMB-X1222-WV) USB2.0 Ports (USB_5_6) (IMB-1223 / IMB-1223-WV)47 : USB3.2 Gen1 Ports (USB3_1_2)

21 : System Panel Header

22 : SMBUS_TEST1

23 : Chassis Intrusion Header (CI1) Close: Active Case Open Open: Normal

24 : Clear CMOS Header (CLRMOS1) 1-2: Normal 2-3: Clear CMOS

25 : SIO_AT1 Open: ATX Mode Short: AT Mode

26 : Chassis FAN Connector (+12V)

27 : EDP_LVDS_SWITCH1 Open: LVDS Short: EDP

28 : AC PWR LOSS Header (AC_PWR_LOSS1) Short: AC Power Loss Open: no AC Power Loss

31 : Power Adapter (For IMB-1222-WV / IMB-X1222-WV Only)

32 : 4-pin ATX PWR Connector 1-2: GND 3-4: DC Input

33 : 2-pin UPS Module Power Input Connector Pin1: GND Pin2: DC Input

+5V

4

2

3

1

GND

RESET#

PWRBTN#PLED-

PLED+

GNDHDLED-

HDLED+

1

GND

1

SignalGND

GND+12V

CHA_FAN_SPEEDFAN_SPEED_CONTROL

1 PIN Signal Name1 GND

2 5VA_CONTROL

3 5VA

4 GND

1

J_SENSE

OUT2_L

MIC_RET

PRESENCE#

GND

OUT2_R

MIC2_R

MIC2_L

OUT_RET

1

1

PIN Signal Name4 OUTRN

3 OUTRP

2 OUTLP

1 OUTLN

1

PIN Signal Name PIN Signal Name9 DDC_CLK 10 DDC_DATA

7 HSYNC 8 VSYNC

5 BLUE 6 GND

3 GREEN 4 GND

1 RED 2 GND

1

30 : M.2 Key-E Socket (M2_KEYE1)

29 : M.2 Key-M Socket (M2_KEYM1)

M.2 Socket Pin Definition3 : M.2 Key-B Socket (M2_KEYB1)

Back Side :SIM Card Socket (SIM1) (For IMB-1222-WV / IMB-X1222-WV / IMB-1223-WV Only)eDP Connector (EDP1, refer to No. 14)

PIN Signal Name5 GND

4 TBT_SLP_S5_S4#

3 SLP_S3#

2 TBCIO_PLUG_EVENT

1 TB_FRC_PWR

Installation of ROM Socket

* Do not apply force to the actuator cover after ic inserted.* Do not apply force to actuator cover when it is opening over 120 degree, Otherwise, the actuator cover may be broken.

* The yellow dot (Pin1) on the ROM must be installed at pin1 position of the socket (white arrow area).* Make sure the white dot on the ROM is installed outwards of the socket.* For further details of how to install ROM, please refer to ASRI website.Warning: If the installation does not follow as the picture, then it may cause severe damage to chipset & MB.