#JF540—War Bonnet Wall Hanging

Materials Included in Kit 18—#1 Safety Pins—Silver 131—#3 Safety Pins—Silver 134—Rondell Beads—Christmas Red 150—6mm Faceted Beads—Christmas Red 226—8mm Faceted Beads—Opaque Black 132—8mm Faceted Beads—Christmas Red 98—Oval Beads—Opaque White 44—Pony Beads—Christmas Red 16—Pony Beads—Opaque Black 8—Pony Beads—Opaque White 210” - 20 Gauge Beading Wire—Silver 36”—Satin Rattail Cord—Black 1 Pkg.—Fluffie Feathers—Red 1 Pkg.—Fluffie Feathers—White Materials Needed Glue or Glue Gun Wire Cutters Ruler

Directions Creating Pins: To add beads to the safety pins, hold one opened safety pin with the point facing away and up. Add beads as shown in the table at the bottom. Begin putting beads on the pin, starting with the beads listed on the bottom and working your way to the head of the pin. PLEASE NOTE: Beads should appear in the same order as shown below. (Make sure to create the number of pins needed of each type, & keep pins separate. 149 Pins Total.) Step 1. Cut your wire into 2—9”, 1—24”, 1—36”, 1—60” and 1—72”

Row 1: Using 2—9” pieces of wire, hold wires together and go through the bottom loop of 1- “A” Pin. Loop

around and go through the bottom loop again to secure, leaving 1 1/2” tail. Keeping both wires together, * add 1—6mm Faceted Bead (Christmas Red). Then thread wire through the bottom loop of 1– “A” Pin. Repeat from * until 18- “A” Pins and 17—6mm Faceted Beads (Christmas Red) have been used. Go through the bottom loop of the last “A” Pin again to secure (same as before), leaving a 1 1/2” tail. Cut off excess wire and form each wire end into a loop for later use.

Due to product availability, we reserve the right to substitute materials used in this kit.

Copyright ©2006 Bolek’s Craft Supplys, Inc. all rights reserved

“A” Pin (#1) (Make 18)

1—6mm Faceted

Bead (Christmas Red)

2—Rondell

Beads (Christmas Red)

“B” Pin (#3) (Make 34)

1—6mm Faceted Bead

(Christmas Red)

1—8mm Faceted Bead

(Opaque Black)

1—Oval Bead (Opaque White)

“C” Pin (#3) (Make 33)

4—8mm Faceted Beads

(Christmas Red)

“D” Pin (#3) (Make 64)

2—8mm Faceted Beads (Opaque Black)

1—Oval Bead (Opaque White)

1

#JF540—War Bonnet Wall Hanging Row 2: Using a 24” piece of wire, thread wire through the head of 1- “A” Pin from the previous row (either Left or Right Side of War Bonnet). Note: Slide pin to center point of wire, twist both sides together to secure. Using twisted wire as one piece, * thread wire through the bottom loop of 1- “B” Pin, add 1—6mm Faceted Bead (Christmas Red). Then thread wire through the bottom loop of 1- “B” Pin. Then thread wire through the head of the next “A” Pin from the previous row. Repeat from * until all 34- “B” Pins and 17—6mm Faceted Beads (Christmas Red) have been used. Note: Before adding last “A” Pin, separate wire, thread one piece of wire through the bottom loop of pin. Twist both ends together to secure. Cut off excess wire. Row 3: Using a 36” piece of wire, thread wire through the head of 1- “B” Pin from the previous row (either Left or Right Side of War Bonnet). Note: Slide pin to center point of wire, twist both wires together to secure. Using twisted wire as one piece, * add 1—Rondell Bead (Christmas Red). Then thread wire through the bottom loop of 1- “C” Pin, add 1—Rondell Bead (Christmas Red). Then thread wire through the head of the next “B” Pin from the previous row, add 1—6mm Faceted Bead (Christmas Red). Then thread wire through the bottom loop of 1- “C” Pin, add 1—6mm Faceted Bead (Christmas Red). Then thread wire through the head of the next “B” Pin from the previous row. Repeat from * until 33- “C” Pins, 34—Rondells (Christmas Red) and 32—6mm Faceted Beads (Christmas Red) have been used. Note: Before adding last “B” Pins, separate wire, thread one piece of wire through the bottom loop of pin. Twist both ends together to secure. Cut off excess wire. Row 4: Using a 60” piece of wire, thread wire through the head of 1- “C” Pin from the previous row. Note: Slide pin to center point of wire, twist both wires together to secure. Using twisted wire as one piece, * add 1—Rondell Bead (Christmas Red). Then thread wire through the bottom loop of 1- “D” Pin, add 1—6mm Faceted Bead (Christmas Red). Then thread wire through the bottom loop of 1- “D” Pin, add 1—Rondell Bead (Christmas Red). Then thread wire through the head of the next “C” Pin from the previous row. Repeat from * until all 64- “D” Pins, 64—Rondell Beads (Christmas Red) and 32—6mm Faceted Beads (Christmas Red) have been used. Note: Before adding last “C” Pins, separate wire, thread one piece of wire through the bottom loop of pin. Twist both ends together to secure. Cut off excess wire. Row 5: Using a 72” piece of wire, thread wire through the head of 1- “D” Pin from the previous row. Note: Slide pin to center point of wire, twist both wires together to secure. Using twisted wire as one piece, * add 1—8mm Faceted Bead (Opaque Black). Then thread wire through the head of the next “D” Pin from the previous row. Repeat from * until 63—8mm Faceted Beads (Opaque Black) have been used. Note: Before adding last “D” Pin, separate wire, thread one piece of wire through the bottom loop of pin. Twist both ends together to secure. Cut off excess wire. TO FINISH: Step 2: To form hanging loop: Cut 1—9” piece of Rattail Cord (Black). Go under center bead of Row 5 and knot ends together. Step 3: Cut remaining Rattail Cord (Black) in half. Using 1 piece of Rattail Cord, thread through loop formed in Row 1. Center Rattail Cord. Thread 17 Pony Bead on each strand in the following order: 3—Christmas Red, 1—Opaque Black, 1—Opaque White, 1—Opaque Black, 5—Christmas Red, 1—Opaque Black, 1—Opaque White, 1—Opaque Black and 3—Christmas Red. Knot ends to secure. Glue feathers to bottom bead (2-3 red/white). Repeat step 3 for 2nd piece of Rattail Cord. Step 4: Glue 1—White Feather to the back of every other Black Bead in Row 5. Glue 1—Red Feather to the back of each remaining black bead in row 5. Copyright ©2006 Bolek’s Craft Supplys, Inc. all rights reserved

2